8-Channel

Surveillance DVR with 4 Cameras & Mobile Monitoring Capabilities

Item 61229

FOR ADVANCED USERSInternet Setup for Remote Use

INITIAL SETUPPhysical Connections

Quick Start Guide

PORT FORWARDING

SMARTPHONE ACCESS

Local Area Network (LAN) Setup

Set Date and Time

In DVR Main Menu

Select System

Set Recording Mode

Motion Detection Settings

ManualWhich

Recording mode?

1

2

4

@

Bunker Hill Security®

B1

B2

B3

B4

D2

D3

D4B5

B1

B2

B1

B2

B1

B2

D5

D1

USB Port Video Input

A

B C

B C DA

Connect Monitor

Connect Cameras

Connect Mouse

Power Input

Video Output

Connect Power

D

BNC/RCA VGA

SelectGeneral

Set Date and Time above

Set Date and Time

Click Apply then OK

ScheduledIn DVR

Main Menu select Record

Press REC on front of DVR - red light will

flash

Select Schedule

Select Channel and Day of

Week

Select boxes for Normal and

Motion

On PC, go to Start Menu, click Run. In DOS window

type “cmd”, click OK.type “ipconfig”press ENTER

STOPEnsure you have a Windows® PC with Internet Explorer®

and a Router before proceeding.

NO

Connect DVR to Router via

Ethernet Cable (Sold Separately)

From DVR Main Menu select

Network > NetworkType = Static

Find the Router’s LANWrite down: 1. Subnet Mask 2. Default Gateway (Router’s IP Address)

In DVR Network > Network change settings:

1. Client Port: 30002. HTTP Port: 3001 3. New IP Address4. Subnet Mask you wrote down5. Default Gateway you wrote down6. DNS1 same as Gateway

Change last 3 digits to a number between

200 and 255

Change last 3 digits to a number between

100 and 255

Click Apply then OK to save changes.

Click Exit, DVR will prompt restart. Click OK.

After restart, on DVR go to

Network > Network to view settings.

Open Internet Explorer®. In address bar, type in

DVR’s IP Address and HTTP Port:http://xxx.xxx.xxx.xxx:3001

(where x = IP Address and 3001 = HTTP Port)Press Enter.

Allow ActiveX Control to install.You may need to adjust the settings in Internet Explorer® by adding the http

address to Trusted Sites and modifying ActiveX controls to allow installation.

After ActiveX Control installs, Log in to DVR

with User Name and Password. @

WARNINGThis Quick Start Guide is not intended toreplace the Owner’s Manual & Safety Instructions. To prevent serious injury, read all safety warnings and instructions therein to ensure proper usage.

In DVR Main Menu

Select SystemSelectUsers

Set User Name and Password

Click Apply then OK

3

Repeat for all Days and all

ChannelsClick Apply

then OK

In DVR Main Menu

Select AlarmSelectMotion

Select Channel

Set Sensitivity LevelSelect Area

Select which Channels will record

Click Apply then OK

Set Buzzer for audible alarm

Set Date and Time above

Set Recording Mode above

Wide Area Network (WAN) Setup

REMOTECOMPUTER

ACCESS

E

Mount Cameras

Note: Monitor and Surge Protector sold separately.

Set up LAN according to

instructions above.

Log in to the Router and go to

Port Forwarding or Applications and

Gaming.

Set start port to 3000 and end port to 3002. Set up both UDP and TCP protocols if the

option is given.

Open Internet Explorer®. In address bar, type in

Default Gateway (from LAN Setup above).Example: xxx.xxx.xxx.xxx

Press Enter.

Find theRouter’s IP Address by going to

whatsmyip.com. Write it down.

On remote computer, Open Internet Explorer®. In address bar,

type in Router’s IP Address and HTTP Port (from LAN Setup above):

http://xx.xxx.xxx.xxx:3001 (where x = IP Address and 3001 = HTTP Port)

Press Enter.

Allow ActiveX Control to install.You may need to adjust the settings in Internet Explorer® by adding the http address to Trusted Sites and

modifying ActiveX controls to allow installation.

After ActiveX Control installs, Log in to DVR

with User Name and Password (from LAN Setup above).

Insert supplied CD into computer and look in

Mobile Software folder for instructions.

In DVR Main Menu

Select Network then Mobile

Set User Name and Password

Set Mobile Port to 3002

Click Apply then OK

Do you have a Windows® PC with Internet Explorer®

and a Router?YES

YES

NO

Create New IP Address:

Are last 3 digits of Default Gateway between 0-99?

See Manual - Page 12

See Manual - Page 17

See Manual - Page 18

See Manual - Page 19

See Manual - Page 28

See Manual - Page 30

EthernetConnection