Upload
podariu
View
98
Download
0
Tags:
Embed Size (px)
DESCRIPTION
vrvvvvvvvvvvvvv
Citation preview
User Manual v0.6.0
VRV Xpress Daikin Europe NV Tom Roels Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13 F: (+32) 59 55 83 90 E: [email protected] http://www.daikineurope.com
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
Air conditioning – Refreshes your life
Table of contents 1 Aim of the development ............................................................................1 2 General features .......................................................................................1 3 Logical steps.............................................................................................1 4 Indoor units tab page ................................................................................1
4.1 Add indoor units.................................................................................2 4.1.1 Automatic selection ....................................................................3 4.1.2 Manual selection.........................................................................3
4.2 Preferences screen ...........................................................................4 4.2.1 Units tab page ............................................................................4 4.2.2 Diagrams tab page .....................................................................4
4.3 Save a project....................................................................................5 5 Outdoor units tab page .............................................................................5
5.1 Add an outdoor unit ...........................................................................6 5.1.1 Selecting a heat pump/cooling only VRV outdoor unit................7 5.1.2 Selecting a heat recovery VRV outdoor unit...............................8
6 Piping tab page.........................................................................................9 6.1 Changing the piping diagram...........................................................11
6.1.1 Changing the position of joints .................................................11 6.1.2 Changing the order of the indoor units .....................................11
7 Wiring tab page.......................................................................................12 7.1 Indoor unit remote controller............................................................12 7.2 Indoor unit options ...........................................................................14 7.3 Outdoor unit options ........................................................................14
8 Centralised controller tab page...............................................................14 9 Reports tab page ....................................................................................15
9.1 Print parameters ..............................................................................17
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
1
Air conditioning – Refreshes your life
� ����������� ������• Day to day VRV jobs • Super quick selection tool for VRV systems • Supporting tool for sales people • Fully automated piping and wiring diagram • Size < 3MB means e-mail able • User friendly and self explanatory selection tool
� ���� ��������• No setup or installation is required. Double click the file VRV
Xpress.exe and all necessary settings are done. • The software makes a shortcut on your taskbar in Start > Programs >
Daikin > VRV Xpress • The extension of the software is *.vrv. Double clicking a saved file will
automatically start the VRV Xpress.exe software.
� ������ ������The logical steps in the VRV Xpress are:
1. Add indoor units to a list (Indoor units tab page) 2. Connect indoor units to outdoor units (Outdoor units tab page) 3. Make changes to the piping diagram (Piping tab page) 4. Make changes to the wiring diagram (Wiring tab page) 5. Define the centralised controllers (Centralised controller tab page) 6. Make a report (Reports tab page)
� ���������������������When starting up the software the below screen appears:
Project name Enter the name of the project. The project name is printed
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
2
Air conditioning – Refreshes your life
on the reports. Reference Enter a reference number. The reference number is
printed on the reports. Client name Enter the client name. The client name is printed on the
reports. Client address Enter the coordinates of the client. The coordinates of the
client are printed on the reports. Refrigerant Choose your desired refrigerant.
Add indoor units to the list (see chapter 4.1 Add indoor units)
Edit an indoor unit that has already been added to the list.
Delete an indoor unit from the list.
Move an indoor unit one position up.
Move an indoor unit one position down.
Start a new project. Open an existing project
Save your project (see chapter 4.3 Save a project).
Exit VRV Xpress
Opens the Preferences screen (see chapter 4.2 Preferences screen)
Opens the about box.
4.1 Add indoor units
When clicking the ‘Add indoor units’ button ( ) the below dialog appears:
Name Name of the indoor unit (e.g. bathroom 1, living room 1,
office 1, …) Manual selection With this option the user can switch between manual
selection and automatic selection of the indoor units (see chapters 4.1.1 Automatic selection and 4.1.2 Manual selection)
Design criteria Depending on whether you have selected the manual selection or automatic selection of the indoor units this screen will change (see chapters 4.1.1 Automatic selection and 4.1.2 Manual selection).
Every time you push this button an indoor unit will be added to the list
Close the Edit indoor unit selection dialog.
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
3
Air conditioning – Refreshes your life
Select options for the selected indoor unit.
4.1.1 Automatic selection If the checkmark Manual selection is unchecked you can enter an indoor unit using the automatic selection:
Name Name of the indoor unit (e.g. bathroom 1, living room 1,
office 1, …) Family You can select the desired family from the drop down
box. Design criteria You can enter the
- Cooling temperature - Heating temperature - Required total cooling capacity - Required sensible cooling capacity - Required heating capacity
Note: 1. The software tries to cover the worst case
scenario. This means that if you enter total, sensible and heating capacity the software will make an indoor unit selection to cover the worst case scenario.
2. If total, sensible or heating capacity values are not available just leave them blank or enter ‘0’.
Every time you push this button an indoor unit will be added to the list
Close the Edit indoor unit selection dialog.
Select options for the selected indoor unit.
4.1.2 Manual selection If the checkmark Manual selection is checked you can enter an indoor unit using the manual selection (this means that you select the indoor units from a drop down list):
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
4
Air conditioning – Refreshes your life
Name Name of the indoor unit (e.g. bathroom 1, living room 1,
office 1, …) Family You can select the desired family from the drop down
box. Model You can select the desired model from the drop down
box. Design criteria You can enter the Cooling temperature and the heating
temperature. Every time you push this button an indoor unit will be
added to the list Close the Edit indoor unit selection dialog.
Select options for the selected indoor unit.
4.2 Preferences screen Pushing the button will pop up the preferences screen:
4.2.1 Units tab page
The user can select his units to display:
- Temperature (°C;°F) - Short length (mm;inch) - Airflow (l/s;m³/h;m³/s) - Capacity (kW;kcal/h;BTU/h;Ton)
4.2.2 Diagrams tab page
The user can select the colour and representation of:
- Devices – drawing colour - Devices – fill colour - Piping – 2 pipes - Piping – 3 pipes - Piping – Oil equalizing line - Wiring – F1F2 - Wiring – P1P2
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
5
Air conditioning – Refreshes your life
- Wiring – Q1Q2 - Wiring – Power lines
The user can select between below representations: - Solid 1pt - Solid 2pt - Solid 3pt - Dotted - Dashed - Dash-dotted
Note: - To change the colour simply click the colour icon next to the item. - To change the representation simply make your selection from the
dropdown box.
4.3 Save a project Every time you save a project the software will automatically add the date and hour when you started your session of the VRV Xpress:
This feature is very interesting to keep the history of changes to a certain project. A session starts from the moment you started a project with the VRV Xpress or you opened an existing project.
� ����������������������The outdoor unit tab page is only available from the moment an indoor unit has been added:
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
6
Air conditioning – Refreshes your life
Name Tree containing an overview of indoor units and BS boxes connected to outdoor units.
Indoor units not yet attached
This list gives an overview of indoor units not yet attached to an outdoor unit
Add an outdoor unit (see chapter 5.1 Add an outdoor unit for further details)
Edit the selected item in the tree view. The item can be: - an indoor unit - a BS Box - an outdoor unit
Delete the selected item in the tree view. The item can be:
- an indoor unit - a BS Box - an outdoor unit
Note 1. If you delete an outdoor unit with connected indoor
units results in indoor units being moved to the ‘Indoor units not yet attached’ list.
2. The same applies when deleting a BS Box.
5.1 Add an outdoor unit
When clicking the ‘Add an outdoor unit’ button ( ) the below screen appears:
Name Name of the outdoor unit (e.g. Outdoor SE, OU NW,
…) Model Selected outdoor unit model Family Family of the outdoor unit:
- Heat pump - Heat recovery - Cooling only
Combination % Select the maximum allowed combination % from the list (100%, 110%, 120% or 130%)
Capacity index Maximum for model
Displays the maximum capacity index for the selected outdoor unit model.
Capacity index Actual
Displays the sum of indoor unit capacity indexes already connected to this outdoor unit.
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
7
Air conditioning – Refreshes your life
Cooling outdoor temperature
Enter the design outdoor temperature for cooling.
Heating outdoor temperature
Enter the design outdoor temperature for heating
Available capacities Cooling
The available cooling capacity of the outdoor unit.
Available capacities Heating
The available heating capacity of the outdoor unit. Note: The calculation takes into account the freeze up correction factor.
(Optional) piping length
You can enter the piping length between the outdoor unit and the indoor unit most far away from the outdoor unit. The software will recalculate the capacities of the indoor units taken into account the capacity correction factor. Note: If you do not want to take into account piping correction factors you just enter ‘0’ as length!
Click this button to select options for the selected outdoor unit.
5.1.1 Selecting a heat pump/cooling only VRV outdoor unit Follow these steps to attach indoor units to the outdoor unit:
1. Highlight the indoor unit that has to be connected to the outdoor unit 2. Drag the indoor unit (= select the indoor unit and hold down the left
mouse button) and drop the indoor unit on the outdoor unit (= while holding down the left mouse button and keep the indoor unit selected you have to move to the outdoor unit).
Note As long as you did not reach the outdoor unit the mouse pointer will look as shown below:
Once you moved upon the outdoor unit the mouse pointer will look as shown below:
Once this icon appears you can release your left mouse button and the indoor unit will be attached to the outdoor unit:
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
8
Air conditioning – Refreshes your life
Note: You can also first multiple select the indoor units that have to be connected to an outdoor unit (= while holding down the shift/ctrl key you select the indoor units). Afterwards you drag and drop the selected indoor units to the outdoor unit. Note: Deselecting an indoor unit from the outdoor unit works in the same way as selecting indoor units, but now you have to move indoor units away from the outdoor unit and drop them into the ‘Available indoor units’ list.
5.1.2 Selecting a heat recovery VRV outdoor unit The difference between a heat pump and a heat recovery unit is the use of BS Boxes. Once you selected heat recovery as outdoor unit family an additional button will appear on your screen:
Follow these steps to add a BX Box:
1. Click the button ‘Add BS Box’ The below screen appears:
Additional button to add BS Boxes
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
9
Air conditioning – Refreshes your life
2. Drag and drop indoor units from the ‘Available indoor units’ list onto the BS Box.
3. Click the OK button The BS Box and its indoor units are connected to the outdoor unit:
� ��������������Once you have selected an outdoor unit the piping tab page becomes available:
Note: As you can see the software tool will generate a fully automated piping diagram. The piping diagrams are generated using joints. To change the order of the indoor units: see chapter 6.1.2 Changing the order of the indoor units. Outdoor unit Select an outdoor unit from the drop down box and
see its corresponding piping diagram.
Clicking this button will pop up the example on how to change the piping diagram (see chapter 6.1.1 Changing the position of joints)
Reset the current piping diagram to its original piping setup. This can be very useful if you change the piping diagram and you notice you have made a
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
10
Air conditioning – Refreshes your life
mistake (see chapter 6.1 Changing the piping diagram)
Full size If this option is checked then the piping diagram will look as follows:
If this option is deselected then the piping diagram will look as follows:
This feature is very useful in case you have more than 10 indoor units connected to an outdoor unit. In this way you can keep track of your actions.
Vertical If this option is checked then the piping diagram will look as follows:
If this option is deselected then the piping diagram will look as follows:
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
11
Air conditioning – Refreshes your life
6.1 Changing the piping diagram The VRV Xpress allows the user to make modifications to the piping diagram. You can:
- change the position of the joints - change the order of the indoor units.
6.1.1 Changing the position of joints To change the position of the joint you simply click on the indoor unit on the piping diagram. The logic to change the position is explained more in detail with below graph:
6.1.2 Changing the order of the indoor units Follow these steps to change the order of the indoor units that are connected to the outdoor unit:
1. Return to the tab page Outdoor unit 2. Expand the outdoor unit that has to be changed 3. Select the indoor unit
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
12
Air conditioning – Refreshes your life
4. Drag and drop the indoor unit to its new position
! "��������������Once you have selected an outdoor unit the wiring tab page becomes available:
Note: As you can see the software tool will generate a fully automated wiring diagram. The wiring diagram follows the piping diagram. All indoor units have by default a remote controller. To remove a remote controller from an indoor unit or interwire indoor units with one remote controller see chapter 7.1 Indoor unit remote controller. To select options for the indoor units see chapter 7.2 Indoor unit options. To select options for the outdoor units see chapter 7.3 Outdoor unit options.
7.1 Indoor unit remote controller Suppose you have the below wiring diagram:
Ind 2 does not need a remote controller and has to be controlled by the remote controller of Ind 3. Follow these steps to interwire indoor units on one remote controller:
1. Right click the indoor unit that needs no remote controller A pop up menu appears:
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
13
Air conditioning – Refreshes your life
2. Choose select options from the menu The below screen appears:
3. Highlight the Wired Remote controller in the ‘Selected options’ list and
click the ‘Remove’ button. The wired remote controller is removed from the 'Selected options' list. 4. Click the OK button The remote controller is removed from Ind 2.
5. Right click Ind 2 and select ‘Remote Controller previous’ if the current
indoor unit has to be controlled by the previous indoor unit in the list (in this case Ind 1) or ‘Remote Controller next’ if the current indoor unit has to be controlled by the next indoor unit in the list (in this case Ind 3). In this case you have to select ‘Remote Controller next’.
The wiring diagram will change as shown below:
Note: To remove the interwire connection:
1. Right click the Indoor unit that is controlled by another indoor unit 2. Choose ‘No remote controller’ from the pop up menu
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
14
Air conditioning – Refreshes your life
7.2 Indoor unit options Follow these steps to select options for indoor units:
1. Right click an indoor unit on the wiring diagram 2. Choose ‘Select options’ from the pop up menu The Used options screen appears:
3. Highlight an option and click the Select button The selected option will move to the Selected Options screen.
7.3 Outdoor unit options Follow these steps to select options for outdoor units:
1. Right click an indoor unit on the wiring diagram 2. Choose ‘Select options’ from the pop up menu The Used options screen appears:
3. Highlight an option and click the Select button The selected option will move to the Selected Options screen.
# $���� ���������� ����������Once the piping and wiring diagram are finished you can switch to the selection of centralised controllers (if you require them):
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
15
Air conditioning – Refreshes your life
Centralized controllers Select the desired centralised control system or
combination of control systems from the list. VRV Xpress will immediately give you an indication of required number of centralised control systems and will make a proposal of connection.
Management system Select the desired management system from the list.
Example:
% &��������������Once you have finished the project you can switch to the Reports tab page:
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
16
Air conditioning – Refreshes your life
Report contents Select the items that have to be included in the
report: - Material list (= bill of material) - Indoor unit details (= overview of all
indoor units) - Outdoor unit details (= overview of all
outdoor units) - Piping diagrams (= include the piping
diagrams in the report) - Vertical (= if this option is checked then
the piping diagrams are printed in a vertical way. If the option is unchecked the piping diagrams are printed in a horizontal way)
- Wiring diagrams (= overview of wiring diagrams and centralised controllers).
Systems included in the reports
Select the systems for which you need a report.
Export to word
Opens up the Print parameters dialog (see chapter 9.1 Print parameters)
Open in word processor If this option is checked the report will open in Microsoft Word. If this option is unchecked the report will be saved to the hard drive.
Export to excel (the files will be saved as *.csv file). What can be exported as *.csv file?
- Material list - Indoor unit details - Outdoor unit details
Open in spreadsheet If this option is checked the report will open in
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
17
Air conditioning – Refreshes your life
your spreadsheet software. If this option is unchecked the report will be saved to the hard drive.
Project not yet complete Overview of errors/warnings still available in your project. If everything is correct than this box will not appear.
9.1 Print parameters
When clicking the Print parameter button ( ) the Print parameter dialog appears:
In this dialog you can:
- enter three lines of text (e.g. company name, address, telephone number,…)
- upload your distributor logo These parameters will be used when generating the report:
www.forofrio.com
Daikin Europe NV Tom Roels
Zandvoordestraat 300, 8400 Oostende (Belgium) T: (+32) 59 55 84 13, F: (+32) 59 55 83 90, E: [email protected] http://www.daikineurope.com
18
Air conditioning – Refreshes your life
Distributor logo
Text lines
www.forofrio.com