VOLUME III Price Bid/Bill of Quantity - Engineering … Bid/Bill of Quantity . NIT No. DLI/CON/684A/579 Dt. 02.08.2017 In figures In words In figures In words 1 Civil Works ( As per

AN ISO 9001 & 14001 COMPANY

TENDER DOCUMENT

TENDER No: DLI/CON/684A/579

FOR

Construction of Balance Work for Institute Building and Fire Fighting

System for New Polytechnic Institute (PKG– I) at Gumla, Jharkhand

VOLUME – III

Price Bid/Bill of Quantity

NIT No. DLI/CON/684A/579 Dt. 02.08.2017

In figures In words In figures In words

1Civil Works ( As per SR JHARKHAND-

2008)5,21,12,105

2Civil Works ( As per DSR 2007+10%

CI)80,91,510

3 Civil Works ( NON SCH) 5,43,126

4Sanitary, water supply & swerage works

(As per SR JHARKHAND-2008)13,29,064

5Sanitary, water supply & sewerage

works (DSR 2007+10% CI)5,86,437

6Sanitary, water supply & sewerage

works (NON SCH)5,040

7

Electrical( internal, external & sub

station), Elevators and other ysytem

Works ( NS/JR-2008 ITEM)

18,04,422

8

Electrical( internal, external & sub

station), Elevators and other sytem

Works (CPWD 2007 ITEM+CI-10%)

27,02,382

9Fire fighting and Prevention

system(NON SCH) 9,93,935

Total: 6,81,68,021

BIDDER'S FINANCIAL OFFER : `

In Figures

`In Words

SEAL

SIGNATURE

Note-The Rate in BOQ are Jharkhand Schedule of rate 2008 for Jharkhand Schedule Items, DSR-2007+10%CI for DSR Items and market rate for NS items

ENGINEERING PROJECTS (INDIA) LTD.

PRICE BID

S.No. ITEM ESTIMATED

COST (in `)

BIDDER'S PRICE AMOUNT IN ` After adding percentage above/ below/ at par

% QUOTE ABOVE / BELOW / AT PAR

Construction of Balance Work for Institute Building and Fire Fighting System for New Polytechnic Institute (PKG– I) at Gumla, Jharkhand

Sl. No. PARTICULARS REVISED

ESTIMATE

1 Civil Works ( As per SR JHARKHAND-2008) 5,21,12,105

2 Civil Works ( As per DSR 2007+10% CI) 80,91,510

3 Civil Works ( NON SCH) 5,43,126

4Sanitary, water supply & swerage works ( As per SR

JHARKHAND-2008)13,29,064

5Sanitary, water supply & sewerage works (As per DSR 2007+10%

CI)5,86,437

6 Sanitary, water supply & sewerage works (NON SCH) 5,040

7Electrical( internal, external & sub station), Elevators and other

sytem Works ( NS/JR-2008 ITEM)18,04,422

8Electrical( internal, external & sub station), Elevators and other

sytem Works (CPWD 2007 ITEM+CI-10%)27,02,382

9 Fire fighting and Prevention system(NON SCH) 9,93,935

10 Sub total 6,81,68,021

GENERAL ABSTRACT

NAME OF WORK : CONSTRUCTION OF BALANCE WORK OF NEW

POLYTECHNIC INSTITUTE AT GUMLA (PKG-I), JHARKHAND

( Based on Schedule of rate of 2008 and D.S.R 2007 + 10 CI)

JSR DSR NON

SCH

JSR DSR NON SCH

EARTH WORK

A1 JR.5.1.1 Earthwork in excavation in foundation trenches in

ordinary soil (vide classification of soil item A) and

disposal of excavated earth as obtained to a distance

upto 50M including all lifts, levelling, ramming the

foundation trenches, removing roots of trees, shrubs all

complete as per approved design, building

specification and direction of E/I

0 Per M³ 39.67 0.00 0.00 0.00

A2 JR. 5.1.2 Extra for earthwork in hard soil as per specification

and direction of E/I (vide classification of soil item B)

480 Per M³ 4.05 1944.00 0.00 0.00

A3 JR.5.1.7 Filling in foundation trenches and plinth in layers not

exceeding 150mm thick well watered, rammed, fully

compacted and fine dressed with earth obtained from

excavation of foundation trenches within a lead of 50

M and lift of 1.5M all complete as per building

specification and direction of E/I (Mode of

measurement compacted volume)

1371 Per M³ 14.56 19961.76 0.00 0.00

A4 JR. 5.1.8 Filling in foundation trenches and plinth in layers not

exceeding 150mm thick well watered, rammed, fully

compacted and fine dressed with earth obtained after

cutting within a lead of 50 M and lift of 1.5M all

complete as per building specification and direction of

E/I (Mode of measurement compacted volume)

680 Per M 33.79 22977.20 0.00 0.00

A5 JR. 5.1.9 Extra for each subsequent lead upto 25M beyond the

initial lead of 50M (Maximum upto 150M lead by

head load) as per specification and direction of E/I

200 Per M³ 3.50 700.00 0.00 0.00

A6 JR.5.1.10 Providing coarse clean sand in filling in foundation

trenches or in plinth including ramming and watering

in layers not exceeding 150 mm thick with all leads

and lifts including cost of all materials, labour, royalty

and taxes all complete as per builiding specification

and direction of E/I (Mode of measurement compacted

volume)

697 Per M³ 112.27 78252.19 0.00 0.00

A7 JR 10.1.3 Jungle clearence including weeding out shrubs, small

trees upto 150mm dia ( girth) and their removal as per


5200 Per sqm 2.41 12532.00 0.00 0.00

A8 DSR 2.33 Felling trees of the girth (measured at a height of 1m

above ground level) including cutting of trunks and

branches removing the roots and stacking of

serviceable material and disposal of unserviceable

material.

a) DSR

2.33.1

Beyong 30cm girth upto and including 60 cm girth 3 each 81.70 0.00 245.10 0.00

b) DSR

2.33.2

Beyong 60cm girth upto and including 120 cm girth 3 each 359.80 0.00 1079.40 0.00

A9 DSR

2.34.1

Supplying chemical emulsion in sealed container

including delivery as specified: Chlorpyriphos/

Lindane emulsifiable concentrate of 20%.

600 litre 174.30 0.00 104580.00 0.00

A10 DSR 2.35 Diluting and injecting chemical emulsion for post

constructional anti-termide treatment (excluding the

cost of chemical emulsion):

a) DSR

2.35.1.1

Along external wall where the apron is not provided

using chemical imulsion @ 7.5 litre / sqm of the

vertical surface of the substructure to a depth of 300m

including excavation channel along the wall and

rodding etc. complete: with Chlorpyriphos/ Lindane

EC 20% with 1% concentration

285 meter 6.75 0.00 1923.75 0.00

b) DSR

2.35.2.1

Along external wall below concrete or masonry apron

using chemical imulsion @ 2.25 litre per linear meter

including drilling and plugging holes etc.with

Chlorpyriphos/ Lindane emulsifiable concentrate of

20% with 1% concentration.

100 meter 10.45 0.00 1045.00 0.00

CIVIL

REVISEDTotal

Quantity

Sl. No Item No Description of Items Unit Rate (in ` )

CIVIL Page 2 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity

Sl. No Item No Description of Items Unit

c) DSR

2.35.3.1

Treatment of soil under existing floors using chemical

emulsion @ one liter per hole, 300mm apart including

drilling 12mm diameter holes and plugging with

cement mortar 1: 2 (1 cement : 2 coarse sand) to match

the existing flooring.with Chlorpyriphos/ Lindane

EC 20% with 1% concentration

2512 sqm 48.70 0.00 122334.40 0.00

MASONRY WORK

A11 JR.5.2.6 Providing designation 75B brick work in C.M. (1:6) in

foundation and plinth with approved quality of clean

coarse sand of F.M. 2 to 2.5 including providing 10

mm thick mortar joints, cost of screening materials,

raking out joints to 15 mm depth, curing taxes and

royalty all complete as per building specification and

direction of E/I

178 Per M³ 1817.70 323550.60 0.00 0.00

A12 JR.5.2.14 Providing designation 75B Brick work in C.M. (1:6) in

superstructure and plinth with approved quality of

clean coarse sand of F.M. 2 to 2.5 including providing

10 mm thick mortar joints, cost of screening materials,

scaffolding raking out joints to 15 mm depth, curing

taxes and royalty all complete as per building


1616 Per M³ 1858.48 3003303.68 0.00 0.00

A13 JR.5.2.23 Providing designation 125 mm thick reinfored

designation 75A brick work in C.M (1:4) in

superstructure with approved quality of clean coarse

sand of F.M. 2 to 2.5 including the cost of screening,

carriage of materials, scaffolding raking out joints to

15 mm depth, curing taxes and royalty (but excuding

the cost of reinforcement) all complete as per building

specification and direction of E/I)

1325 Per M² 262.46 347759.50 0.00 0.00

A14 JR.5.2.24 Providing 75mm thick reinforced designation 75A

Brick work in cement mortar (1:4) in superstructure

with approved quality of clean coarse sand of F.M. 2

to 2.5 including the cost of screening, carriage of

materials, scaffolding raking out joints to 15 mm

depth, curing taxes and royalty (excuding the cost of

reinforcement all complete as per building

specification and direction of E/I)

60 Per M² 157.46 9447.60 0.00 0.00

CONCRETE WORK

A15 DSR 4.1 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering- all work up to plinth level:

a) DSR 4.1.3 1:2:4 (1 cement : 2 coarse sand: 4 graded stone

aggregate 20mm nominal size)

20 cum 3257.45 0.00 65149.00 0.00

A16 JR.5.3.3 Providing P.C.C. M.100 with nominal mix of (1:3:6)

in foundation with approved quality of stone metal

grade III (50 mm to 25 mm size) clean coarse sand of

F.M. 2.5 to 3 including screening, shuttering , mixing

cement concrete in mixer and placing in position,

vibrating, striking, curing taxes and royalty all


Engineer-in-charge

293 Per M³ 2184.21 639973.53 0.00 0.00

A17 JR.5.3.4 Providing P.C.C. M.75 with nominal mix of (1:4:8) in

foundation with approved quality of stone metal grade

III (50 mm to 25 mm size) clean coarse sand of F.M.

2.5 to 3 including screening, shuttering , mixing


vibrating, striking, curing taxes and royalty all


Engineer-in-charge

0 Per M³ 1943.81 0.00 0.00 0.00

A18 JR

5.3.16.1

Providing and laying damp proof course 40mm thick

with cement concrete 1:2:4 (1cement :2coarse sand: 4

graded stone aggregate 12.5mm nominal size)

195 sqm 100.87 19669.65 0.00 0.00

CIVIL Page 3 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A19 JR.5.3.17 Providing 35mm, thick precast R.C.C.M. 150 with

nominal mix of (1:2:4) shelves with approved quality

of stone chips of 12mm to 6 mm size graded and clean

coarses sand of F.M. 2.5 to 3 with 1.5mm cement

punning at top and side and 6mm. Cement plaster (1:4)

at bottom including screening, curing and placing the

slab in position (but excluding the cost of

reinforcement) taxes and royalty all complete as per

building specification and direction of E/I

100 Per M² 209.00 20900.00 0.00 0.00

A20 JR.5.3.24 Providing 75X125mm R.C.C.M 150 with nominal mix

of (1:2:4) Hand rail over brick railing with approved

quality of stone chips 20mm to 6mm, size graded and

clean coarse sand of F.M 2.5 to 3 finished with cement

plaster (1:4) with punning including

screening,shuttering, mixing the concrete properly and

placing in position striking, curing and finished with

rounded edges (but excluding the cost of

reinforcement) and taxes all complete as per


693 Per M 67.23 46590.39 0.00 0.00

A21 JR.5.3.25 Providing G.I. pipe hand rails with 40mm G.I pipe of

I.T.C or equivalent make properly fitted and fixed in

position to rail posts with all necessary accessories and

taxes all complete, as per building specification and

direction of E/I

472 Per M 239.80 113185.60 0.00 0.00

A22 JR.5.3.27 Providing 50mm thick precast R.C.C.M 150 with

nominal mix of (1:2:4) jali with approved quality of

stone chips 12mm and down well graded and clean

coarse sand of F.M 2.5 to 3 finished with1.6mm thick

M.S wire as per approved drawing and design and

placing the same in position true to plumb and level

with 6mm dia M.S. rods placed at regular intervals

both horizontally and vertically as required properly

grouted with C.M (1:3) including cost of curing,

scaffolding and finishing all complete as per building

specifications and direction of E/I

96 Per M² 244.06 23429.76 0.00 0.00

A23 JR. 5.3.5.1 Providing R.C.C.M-200 with nominal mix of (1:1:5:3)

in foundation and plinth with approved quality stone

chips 20mm to 6 mm size graded and clean coarse

sand of F.M 2.5 to 3 including screening, shuttering

mixing cement concrete in mixer and placing in

position, vibrating, striking, curing, (but excluding the

cost of reinforcement) taxes and royalty all complete as

per building specification and direction of Engineer-in-

charge

0 Per M³ 3384.98 0.00 0.00 0.00

A24 JR. 5.3.6.1 Providing R.C.C.M-200 in band plinth level with

approved quality stone chips 20mm to 6 mm size

graded and clean coarse sand of F.M 2.5 to 3 including

screening, shuttering mixing cement concrete in mixer

and placing in position, vibrating, striking, curing, (but

excluding the cost of reinforcement, taxes and royalty

all complete as per building specification and direction

of Engineer-in-charge)

26 Per M³ 3739.49 97226.74 0.00 0.00


lintel with approved quality stone chips 20mm to 6 mm

size graded and clean coarse sand of F.M 2.5 to 3

including screening, shuttering mixing cement

concrete in mixer and placing in position, vibrating,

striking, curing, (but excluding the cost of

reinforcement, taxes and royalty all complete as per

building specification and direction of Engineer-in-

charge

88 Per M³ 4294.15 377885.20 0.00 0.00


in roof slab with approved quality stone chips 20mm to

6 mm size graded and clean coarse sand of F.M 2.5 to

3 including screening, shuttering mixing cement





charge)

1191 Per M³ 4337.19 5165593.29 0.00 0.00

CIVIL Page 4 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A27 JR. 5.3.11 Providing R.C.C.M-200 with nominal mix of (1:1½:3)

in beam of all types with approved quality stone chips

20mm to 6 mm size graded and clean coarse sand of

F.M 2.5 to 3 including screening, shuttering mixing


vibrating, striking, curing, (but excluding the cost of



charge)

687 Per M³ 4707.53 3234073.11 0.00 0.00

A28 JR. 5.3.14 Providing R.C.C.M-200 with nominal mix of (1:1½:3)

in columns with approved quality stone chips 20mm to

6 mm size graded and clean coarse sand of F.M 2.5 to

3 including screening, shuttering mixing cement





charge

262 Per M³ 3904.11 1022876.82 0.00 0.00

A29 JR.

5.3.15.1

Providing av 63mm thick R.C.C.M - 200 with nominal

mix of (1:1:5:3) chajja with approved quality of stone

chips 20mm to 6 mm size graded and clean coarse

sand of F.M 2.5 to 3 including screening, shuttering

mixing cement concrete in mixer and placing in

position, vibrating, striking, 6mm cement plaster (1:4)

in ceiling and sides of chajja with sand of F.M. 1.5

curing (but excluding the cost of reinforcement) taxes

and royalty all complete as per building specification

and direction of Engineer-in-charge)

35 Per M² 501.90 17566.50 0.00 0.00

A30 JR.

5.3.18.1

Providing R.C.C.M -200 with nominal mix of

(1:1:5:3)in stair case with approved quality of stone

chips 20mm to 6mm size graded and clean coarses

sand of F.M. 2.5 to 3 including centering, shuttering,

screening, mixing cement concrete in mixer, placing in

position, vibrating, striking, curing taxes and royalty all

complete, as per buildin specification and direction of

Engineer-in-charge)

116 Per M³ 6647.10 771063.60 0.00 0.00

A31 DSR 5.11 Extra for additional height in centering, shuttering

where ever required with adequate bracing, propping

etc. including cost of de-shuttering and decentering at

all levels, over a height of 3.5 m for every additional

height of 1 metre or part thereof (plan area to be

measured)

2400 sqm 70.20 0.00 168480.00 0.00

WOOD WORK

A32 JR.5.4.13 Supplying, fitting and fixing 38 mm thick good quality

well dressed well seasoned wood fully paneled shutters

(frame made of sal wood and panels of sisum wood) in

doors and windows with 25mmthick panels including

wedge over all clamps complete including application

of two coats of wood preservative of approved quality

on the surface butting walls and lintels all complete as

per building specification and direction of E/I

157 Per M² 2075.16 325800.12 0.00 0.00

A33 JR.5.4.38 Supplying, fitting and fixing 35mm thick solid core

type non decorative single leaf flush shutters in doors

and windows with black board core blended with high

quality phenol format dehyde synthetic resin both side

commercial veneered of standard make with oxidised

iron fittings such as hinges, sliding doors, tower bolts,

handles, cleats, sand blocks and taxes all complete as

per building specification and direction of Engineer -

in- charge

93 Per M² 885.45 82346.85 0.00 0.00

A34 JR.5.4.39 Supplying, fitting and fixing 35mm thick solid core

type non decorative double leaf flush shutters in doors

and windows with black board core blended with high

quality phenol format dehyde synthetic resin both side

commercial veneered of standard make with oxidised

iron fittings such as hinges, sliding doors, tower bolts,

handles, cleats, sand blocks and taxes all complete as

per building specification and direction of Engineer -

in- charge

189 Per M² 942.33 178100.37 0.00 0.00

CIVIL Page 5 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A35 DSR 9.24 Extra for providing vision panel not exceeding 0.1 sqm

in all type of flush doors, (cost of glass

excluded)(overall area of door shutter to be measured)

: Rectangular or square.

8 sqm 99.90 0.00 799.20 0.00

A36 non-

schedule

Supplying, fitting and fixing glass panes including

supplying putty beads and nails etc all complete as per

building specification and direction of E/I: 4mm plain

glass.

8 sqm 400.00 0.00 0.00 3200.00

A37 DSR 9.76 Providing and fixing bright finished brass 100mm

mortice latch and lock with 6 levers and a pair of lever

handles with necessary screws etc complete (best make

of approved quality).

90 Each 332.65 0.00 29938.50 0.00

A38 DSR

9.62.2

Providing & fixing ISI marked oxidised MS sliding

door bolts with nuts & screws etc. complete

250 x 16 mm 26 each 69.65 0.00 1810.90 0.00

STEEL WORK

A39 JR.5.5.1 Providing reinforcement of 6mm dia rods as per

approved design and drawing excluding carriage of

Rods (straight or in coils) to work site, cutting,

bending, and binding with annealed wire with cost of

wire, removal of rust, placing the rods in position all


E/I a) 6mm dia Gr. A

2 Per MT 48732.30 85281.53 0.00 0.00

A40 JR.5.5.4 Providing Tor Steel reinforcement of 8mm dia rods as

per approved design and drawing excluding carriage of

Rods (straight or in coils) to work site, cutting,

bending, and binding with annealed wire with cost of

wire, removal of rust, placing the rods on position all


E/I TMT Fe 500.8 to 10 Tor

202 Per MT 54744.31 11058350.62 0.00 0.00

A41 JR.5.5.5 Providing Tor Steel reinforcement of 10mm,12mm &

16mm dia rods as per approved design and drawing

excluding carriage of Rods (straight or in coils) to

work site, cutting, bending, and binding with annealed

wire with cost of wire, removal of rust, placing the

rods on position all complete as per building

specification and direction of E/I 12mm (TMT coil Fe

500).

12mm (TMT bar Fe500) 56 Per MT 55431.39 3104157.84 0.00 0.00

16mm (TMT bar Fe500) 96 Per MT 53822.99 5167007.04 0.00 0.00

A42 JR.5.5.6 Providing Tor Steel reinforcement of 20mm & 25mm

dia bars as per approved design and drawing excluding

carriage of Rods (straight or in coils) to work site,

cutting, bending, and binding with annealed wire with

cost of wire, removal of rust, placing the rods on

position all complete as per building specification and

direction of E/I

a) TMT bar 20/25mm Fe 500 66 Per MT 52448.81 3461621.46 0.00 0.00

b) TMT bar 28/32 mm Fe 500 0 Per MT 82935.96 0.00 0.00 0.00

A43 JR.5.5.12 Supplying, fittings and fixing M.S. grill made of

20X6mm M.S. flat as per approved design and

drawing, properly fabricated with joints continous fillet

welded & finished smoth, carriage of grill to work site,

hoisting as per building specification and direction of

E/I.( where materials is not supplied by the deptt.)

15250 Kg 51.19 780647.50 0.00 0.00

A44 JR.5.5.13 Providing and fixing fan hook of 16mm dia M.S. bar 1

metre long bent to required size and shape, placed in

position and fixed in R.C.C slab/beam at the time of

casting all complete as per building specification and

direction of E/I (where material is not supplied by

deppt.)

416 Each 89.60 37273.60 0.00 0.00

CIVIL Page 6 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A45 JR.5.5.14 Supplying, fitting and fixing collapsible gate of

approved size and make properly fabricated with

vertical double channels 20X10X2mm at 100mm

centres and braced with M.S. flat diagonals

20X3mm,with top and bottom rails of T iron

40X40X6mm with 38mm dia steel pulleys complete

with bolts, nuts, locking arrangements, stoppers,

handles, including applying a priming coat of red lead

paint, carriage, hoisting and taxes all complete as per

building specification and direction E/I

8 Per M² 2301.36 19331.42 0.00 0.00

A46 JR.5.5.27 Supplying, fitting and fixing 40mm dia G.I pipe fitted

and fixed in floor outlet to drain out water, in cement

concrete including cutting hole, making good the wall

and finishing, all complete as per building


250 Each 70.31 17577.50 0.00 0.00

A47 JR.5.5.18 Supplying, fitting and fixing fully glazed steel door

windows or ventilations of standard rolled 'Z' and

mullion steel sections and size as per IS 1038 joints

met and welded with 100X16X3mm, M.S lugs fixed in

cement concrete (1:2:4)blocks 15X10X10mm

sizeincluding cost of oxidised iron fittings, with

hings,handles per steps,catchsprings, 3mm thick plain

glass panes with Aluminium beads and inner frame

fixed with lugs with 20mm long 6.3mm G.I counter

sunk machine screw and nuts and applying a coat of

red lead paint carriage to work site hoisting and

placing in all storeys and taxes all complete as per


1200 Per M² 1886.07 2263284.00 0.00 0.00

A48 DSR 9.12 Extra for providing frosted glass panes 4mm thk.

instead of ordinary glass panes 4mm thk indoors,

windows, clerestory window shutters.

68 Sqm 10.45 0.00 710.60 0.00

A49 D.S.R.

10.23

Providing and fixing bright finished brass casement

window fastners or peg stays to windows / ventilators

with necessary welding and machine screws etc.

complete

500 Kg 226.05 0.00 113025.00 0.00

A50 D.S.R.

10.13

Providing and fixing T-iron frames for doors, windows

and ventilators of mild steel Tee-sections, joints mitred

and welded with 15x3mm lugs 10cm long embedded

in cement concrete blocks 15x10x10 cm. Of 1:3:6 (1

cement : 3 coarse sand: 6 graded stone aggregate

20mm nominal size) or with wooden plugs and screws

or rawl plugs and screws or with fixing clips or with

bolts and nuts as required including fixing of necessary

butt hinges and screws and applying a priming coat of

approved steel primer.

4800 kilogram 51.15 0.00 245520.00 0.00

A51 DSR 10.25 Steel work welded in built up section /framework

including cutting, hoisting , fixing in position and

applying a priming coat of approved steel primer using

structural steel etc. as required.

DSR

10.25.2

In gratings, frames, guard bar, ladders, railings,

brackets, gates and similar works

16500 kg 51.20 0.00 844800.00 0.00

A52 DSR 10.6 Supplying and fixing rolling shutters of approved

make, made of required size M.S. laths interlocked

together through their entire length and jointed

together at the end by end locks mounted on specially

designed pipe shaft with brackets, side guides and

arrangements for inside and outside locking with push

and pull operation complete including the cost of

providing and fixing necessary 27.5 cm long wire

springs grade No. 2 and M.S. top cover of required

thickness for rolling shutters.

DSR

10.6.2

80 x 1.20mm M.S. laths with 1.20 mm thick top cover 20 sqm 965.35 0.00 19307.00 0.00

A53 DSR 10.7 Providing and fixing ball bearings for rolling shutters 4 each 356.50 0.00 1426.00 0.00

CIVIL Page 7 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A54 D.S.R.

9.84

Providing and fixing IS : 3564 marked aluminium

extruded section body tubular type universal hydraulic

door closer with double speed adjustment with

necessary accessories and screws etc. complete

90 each 911.00 0.00 81990.00 0.00

FLOORING WORK

A55 JR.5.6.1 Providing designation 75A one brick flat soling joints

filled with local sand including cost of watering taxes


direction of E/I

2563 Per M² 110.62 283519.06 0.00 0.00

A56 JR.5.6.9 Providing 50mm thick cement concrete flooring

(1:2:4) with 20mm to 6mm, size graded stone chips

finished with flooring coat of neat cement in panels

including cost of curing finishing the surface smooth

by rubbing with carborandum stone, taxes and

royalality with all complete as per building


153 Per M² 193.15 29551.95 0.00 0.00

A57 JR 5.6.10 Providing 12mm cement plaster (1:3) with clean

coarse sand of F.M 1.5 with floating coat of neat

cement in skirting including rounding of junctions with

floor, curing, taxes and royalty all complete as per

building specification and direction of E/I.

10 Per M² 87.89 878.90 0.00 0.00

A58 DSR.11.20 Chequered precast cement concrete tiles 22mm thick

in footpath and courtyard jointed with neat cement

slurry mixed with pigment to match the shade of tiles

including rubbing and cleaning etc. complete on 20mm

thick bed of cement mortar 1:4(1 cement: 4 coarse

sand)

DSR

11.20.3

Dark shade using ordinary cement 890 Sqm 480.95 0.00 428045.50 0.00

A59 DSR.11.4 52 mm thick cement concrete flooring with concrete

hardener topping under layer 40 mm thick cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm nominal size) and top layer 12

mm thick cement hardener of mix 1:2 (1 cement

hardener mix : 2 graded stone aggregate 6 mm

nominal size) by volume hardening compound is

mixed @ 2 litre per 50 kg of cement or as per

manufacturers specifications. This includes cost of

cement slurry, but excluding the cost of nosing of steps

etc. complete

1480 sqm 286.55 0.00 424094.00 0.00

A60 JR

5.6.23.1

Providing and laying 6mm precast white glazed tiles in

walls over 12mm cement mortar (1:3) and jointed with

grey cement slurry flush pointed with white cement

including rubbing polishing and cost of curing, taxes

and royalty all complete as per building specification

and direction of E/I - with "A" grade white 15x15cm

tiles

960 sqm 561.57 539107.20 0.00 0.00

A61 JR5.6.19 Providing and laying 15 to 23mm thick Kotah stone

slab flooring of approved size texture and colour over

19mm thick base of lime mortar (1:1:1) ( lime putty:

surkhi:coarse sand) laid over and jointed with grey

cement slurry mixed with pigement to match the shade

of slab including rubbing and polishing to granolithic

finish with approved quality of carborandom stone

including cost of curing taxes and royalty all complete

as per building specification and direction of E/I

iii) 450x 450 size 3225 Per M² 855.22 2758084.50 0.00 0.00

A62 JR 5.6.20 Providing and laying 15 to 23mm thick Kotah stone

tiles in risers of steps skirting and pillers of approved

size texture and colour laid over 12mm thick cement

mortar (1:3) and jointed with grey cement slurry mixed

with pigement to match the shade of the slab including

rubbing to grnolithic finish with approved quality of

carborandom stone including cost of curing taxes and


direction of E/I-

475 Per M² 807.03 383339.25 0.00 0.00

CIVIL Page 8 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A63 JR

5.6.14.2

Providing and laying hydraulically machine pressed

terrazo tiles 20mm thick of approved texture with

down marble chips of approved shade size and quality,

laid on 19mm thick bed of lime mortar (1:1:1) ( lime:

surki : sand) with neat cement slurry mixed with

pigment to match the shade of tiles between joints,

including rubbing and polishing to granolithic finish

with approved quality of carborandom stone including

cost of curing taxes and roality all complete as per

building specification and direction of E/I.

Other colour excluding grey with 100% ordinary

cement

2940 Per M² 517.47 1521361.80 0.00 0.00

A64 JR

5.6.16.2

Providing and laying hydraulically machine pressed

precast terrazo tiles 20mm thick in skirting of

approved texture with 4mm down marble chips of

approved shade size and quality, over 12mm thick

cement plaster (1:3) base with neat cement slurry

mixed with pigment to match the shade of tiles

between joints, including rubbing and polishing to

granolithic finish with approved quality of

carborandom stone including cost of curing taxes and

roality all complete as per building specification and

direction of E/I.

Other colour excluding grey with 100% ordinary

cement

205 Per M² 551.52 113061.60 0.00 0.00

A65 Non sch Providing and fixing homogeneous Polyvinyl chloride

sheet/tile in flooring and skirting in approved pattern

on a smooth and damp proof base using rubber base

adhesives of approved quality and manufacturer like

Dunlop S-758, Fevicol SR 998 or equivalent in

Non sch 2.0mm thick Tile. 171 Sqm 650.00 0.00 0.00 111150.00

A66 DSR.11.41

.2

Providing and laying polished vitrified floor tiles in

different sizes (thickness to be specified by the

manufacturer) with water absorption's less than 0.08%

and conforming to IS : 15622 of approved make in all

colours and shades, laid on 20 mm thick cement

mortar 1:4 (1 cement : 4 coarse sand) including

grouting the joints with white cement and matchsing

pigments etc. complete

Size of tile 60 x 60 cm 1508 Sqm 1031.86 0.00 1556044.88 0.00

PLASTER WORK

A67 JR.5.7.3 Providing 12mm thick cement plaster (1:6) with clean

coarse sand of F.M 1.5 including screening, curing

with all leads and lifts of water, scaffolding taxes and


direction of E/I.

15000 Per M² 53.40 801000.00 0.00 0.00

A68 JR.5.7.7 Providing cement deep rulled pointing (1:3) with clean

coarse sand of F.M 1.5 including screening, curing

with all leads and lifts of water, scaffolding taxes and


direction of E/I.

3000 Per M² 51.21 153630.00 0.00 0.00

A69 JR.5.7.11 Providing 1.5mm cement punning including curing,

carriage of water with all leads and lifts as per building


260 Per M² 20.26 5267.60 0.00 0.00

A70 JR.5.7.14 Providing 12mm thick water proof cement plaster (1:3)

with clean coarse sand of F.M. 1.5 with 5% cico or any

other approved water proofing compound including

scrrening, curing with all leads and lifts of water,

scaffolding taxes and royalty all complete as building


350 Per M² 72.58 25403.00 0.00 0.00

A71 JR.5.7.15 Providing 19mm thick water proof cement plaster (1:3)

with clean coarse sand of F.M. 1.5 with 5% cico or any

other approved water proofing compound including

scrrening, curing with all leads and lifts of water,

scaffolding taxes and royalty all complete as building


8200 Per M² 103.60 849520.00 0.00 0.00

CIVIL Page 9 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A72 JR 5.7.6 Providing 6mm thick cement plaster (1:4) in celling

with clean coarse sand of F.M 1.5 including screening,

curing with all leads and lifts of water, scaffolding

taxes and royalty all complete as per building

specification and direction of E/I.

11500 Per M² 53.71 617665.00 0.00 0.00

A73 JR 5.7.20 Extra for plaster work over exterior surface for each

consequetive floors above first floor includding cost of

scaffolding etc. complete as per direction of E/I.

11800 Per M² 5.68 67024.00 0.00 0.00

FINISHING WORK

A74 JR.5.8.3 White washing three coats over new surface with

approved quality lime including cost of cleaning

surface thoroughly and removing the scales of smoke

and mosh marks with jhama rubbing, scaffolding

washing, of floors and taxes all complete as per


12700 Per M² 5.16 65532.00 0.00 0.00

A75 JR.5.8.6 Colour washing twocoats over a coat of white wash

over new surface with approved quality lime including

cost of cleaning surface thoroughly and removing the

scales of smoke and mosh marks with jhama rubbing,

scaffolding washing, of floors and taxes all complete

as per building

6200 Per M² 8.87 54994.00 0.00 0.00

A76 DSR.13.26 Providing and applying plaster of paris putty of 2 mm.

thickness over plastered surface to prepare the surface

even and smooth complete

6500 sqm 47.20 0.00 306800.00 0.00

A77 JR.5.8.18 Providing two coats of oil bound distemper of

approved shade and make over a coat of cement primer

over new surface including preparing the plastered

surface by rubbing smooth with pumice stone or fine

sand paper applying putty wherever required

scaffolding washing of floors and taxes all complete as

per building specification and direction of E/I

6500 Per M² 42.68 277420.00 0.00 0.00

A78 JR.5.8.21 Providing two coats of plastic emulsion paint of

approved shade and make over a coat of cement primer

over new surface including preparing plastered surface

by rubbing smooth with pumice stone or fine sand

paper, applying putty wherever required scaffolding

washing of floors and taxes all complete as per


1000 Per M² 77.64 77640.00 0.00 0.00

A79 JR.5.8.29 Providing two coats of painting with ready mixed paint

over a coat of primer of approved shade and make over

new wooden surface including preparing the surface

after cleaning, removing dirt scales, smokes, grease

and sand preparing, including cost of scaffolding and

taxes all complete as per building specification and

direction of E/I

1200 Per M² 58.49 70188.00 0.00 0.00

A80 JR.5.8.43 Providing two coats of painting with ready mixed paint

of approved shade and make over steel surface

including cleaning the surface thoroughly, scaffolding

and taxes all complete as per building specification

and direction of E/I

3250 Per M² 33.69 109492.50 0.00 0.00

A81 JR.5.8.46 Providing one coat of aluminium paint over steel

srface including cleaning the surface thoroughly,

scaffolding and taxes all complete as per building


50 Per M² 42.15 2107.50 0.00 0.00

A82 13.48 Finishing walls with Deluxe Multi surface paint system

for interiors and exteriors using Primer as per

manufacturers specifications:

10200 sqm 62.25 0.00 634950.00 0.00

13.48.1 Two or more coats applied @ 1.25 ltr/10 sqm. Over

and including one coat of Special primer applied @

0.75 ltr / 10 sqm

MISCELLANEOUS WORK

CIVIL Page 10 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A83 DSR 22.7 Providing and laying integral cement base waer

proofing treatment including preparation of surface as

required for treatment of roofs, balconies, terraces etc

consisting of following operations: a) Applying a

slurry coat of neat cement using 2.75 kg/sqm of

cement admixed with watr proofing compound

conforming to IS : 2645 and approved by Engineer - in

- charge over the RCC slab including adjoining walls

up to 30 mm height including cleaning the surface

before treatment. b) Laying brick bats with mortar

using broken bricks/brick bats 25 mm to 115mm size

with 50% of cement mortar 1:5 (1 cement : 5 coarse

sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer - in

- charge to require slope and treating similarly the

adjoining walls upto 300 mm height including

rounding the junctions of walls and slabs c) After two

days of proper curing applying a second coat of cement

slurry using 2.75 kg /sqm of cement admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineer - in charge.

d) Finishing the surface with 20 mm thick jointless

cement mortar of mix 1:4 (1cement : 4 coarse sand)

admixed with water proofing compound conforming to

IS:2645 and approved by Engineer - in -charge

including laying glass fibre cloth of approved quality in

top layer of plaster and finally finishing the suface with

trowel with neat cement slurry and making pattern of

300X300mm square 3mm deep. e) The whole terrace

so finished shall be flooded with water for a minimum

period of two weeks for curing and for final test. All

above operations to be done in order and as directed

and specified by the Engineer-in-Charge:

DSR

22.7.1

With average thickness of 120 mm and minimum

thickness at khurra as 65 mm.

2360 Per M² 541.50 0.00 0.00 1277940.00 0.00

A84 DSR 25.5 Providing and laying water proofing treatment in

sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement

compound consisting of applying : a) First layer of

slurry cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/sqm. This

layer will be allowed to air cure for 4 hours.

b) Second layer of slurry of cement @ 0.242 kg/sqm

mixed with water proofing cement compound @ 0.126

kg/sqm. This layer will be allowed to air to air to cure

for 4 hoursfollowed with water curing for 48 hours.

The rate includes preparation of surface, treatment and

sealing of all joints, corners, junctions of pipes and

masonary with polymer slurry.

505 sqm 143.85 0.00 72644.25 0.00

A86 JR.5.10.33 Providing 250mm wide brick drain in cement mortar

(1:6) with av 150mm clear depth and 250mm, apron

including cost of earthwork involved with 75mm

cement concrete (1:4:3) over one brick designation

75A flat soling in proper grade and slope at the base

the drain duly plastered in Cm.(1:3) with punning over

exposed surface all complete as per building


290 Per M 514.21 149120.90 0.00 0.00

A86 DSR

12.40.2

Providing and fixing on wall face unplasticised - rigid

P.V.C rainwater pipes conforming to IS: 13592. Type

A including jointing with seal ring conforming to IS:

5382 leaving 10mm gap for thermal expansion

:110mm diameter

525 metre 163.40 0.00 85785.00 0.00

A87 DSR 12.42 Providing and fixing on wall face unplasticised -

P.V.C moulded fittings / accessories for unplasticised -

Rigid P.V.C rain water pipes conforming to IS :

13592 Type A including jointing with seal ring

conforming to IS : 5382 leaving 10mm gap for thermal

expansion

a) 12.42.1.2 Coupler:110mm 35 each 101.65 0.00 3557.75 0.00

b) 12.42.3.2 Single tee with door: 110x110x110mm 35 each 260.70 0.00 9124.50 0.00

c) 12.42.5.2 Bend 87.5o:110mm bend 35 each 134.20 0.00 4697.00 0.00

d) 12.42.6.2 Shoe(plain):110mm Shoe 35 each 263.10 0.00 9208.50 0.00

CIVIL Page 11 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A88 DSR

12.43.2

Providing and fixing unplasticised -PVC pipe clips of

approved design to unplasticised -PVC rainwater pipes

by means of 50x50x50mm hard wood plugs , screwed

with MS screws of required length including cutting

brickwork and fixing in cement mortar 1:4( 1 cement:

4 coarse sand) and making good the wall etc.

complete.:110mm

525 each 96.90 0.00 50872.50 0.00

A89 DSR 12.44 Providing and fixing to the inlet mouth of rain water

pipe cast iron grating 15 cm diameter and weighing

not less than 440 grams.

35 each 23.40 0.00 819.00 0.00

A90 DSR 19.15 Providing M.S. foot rests including fixing in manholes

with 20X20X10 cm cement concrete blocks 1:3:6 (1

cement : 3 coarse sand : 6 graded stone aggregate 20

mm nominal size) as per standard design.

75 each 149.85 0.00 11238.75 0.00

A91 DSR

8.10.1

Providing and fixing stone slab table rubbed, edges

rounded and polished of size 75 x 50 cm deep and 1.8

cm thick fixed in urinal partitions by cutting a chase of

appropriate width with chase cutter and embedding the

stone in the chase with epoxy grout or with cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 6 mm nominal size) as per direction of

Engineer-in-charge and finished smooth. White Agaria

Mrble Stone

18 sqm 2274.45 0.00 40940.10 0.00

A92 DSR 4.17 Making plinth protection 50mm thick of cement

concrete 1: 3: 6 ( 1 cement: 3 coarse sand :6 graded

stone aggregate 20 mm nominal size) over 75mm bed

of dry brick ballast 40mm nominal size well rammed

and consolidated and grouted with fine sand including

finishing the top smooth.

300 sqm 222.65 0.00 66795.00 0.00

A93 non-

schedule

Providing and laying 40mmx25mm (WxD) two-

compound polysulphide based sealant compound of a

base compound of liquid polysulphide polymer and an

accelerator in expansion joints .The joints shall be

cleaned thoroughly and be completely free from

frost,dirt,dust,oil,grease or any other loose materials

.Appropriate primer suitable for porous surface like

cement shall be applied on side of the joints .Fibre

filler board to be inserted to adjust the joints (The

application shall be strictly done as per specification

and direction of the manufacturer):Gungrade for

horizontal and vertical joints:40mm x25mm(WxD)

340 Rmt 794.00 0.00 0.00 269960.00

A94 DSR: 21.1 Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded built

up standard tubular sections / appropriate Z sections

and other sections of approved make conforming to IS

: 733 and IS : 1285, fixed with rawl plugs and screws

or with fixing clips or with expansion hold fasteners

including necessary filling up of gaps at junctions, at

top, bottom and sides with required PVC / neoprene

felt etc. Aluminium sections shall be smooth, rust free,

straight, mitred and jointed mechanically wherever

required including cleat angle.l Aluminium snap

beading for glazing / panelling, C.P. brass / stainless

steel screws all complete as per architectural drawings

and the directions of Engineer-in-charge. (Glazing and

panelling to be paid for separately)

a) DSR

21.1.1.1

For fixed portion : Anodised aluminium (anodised

transparent or dyed to required shade according to IS :

1868. Minimum anodic coatring of grade AC 15)

300 Kg 290.45 0.00 87135.00 0.00

b) DSR

21.1.2.1

For shutters of doors windows & ventilators includisng

providing and fixing hinges / pivots and making

provision for fixing of fittings wherever required

including the cost of PVC / neoprene gasket required

(Fittings shall be paid for separately). : Anodised

aluminium (anodised transparent or dyed to required

shade according to IS : 1868. Minimum anodic

coatring of grade AC 15)

500 Kg 310.45 0.00 155225.00 0.00

CIVIL Page 12 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


A95 DSR 21.3 Providing and fixing glazing in aluminium

doors,window,ventilator shutters and partitions etc.

with PVC/neoprene gasket etc. complete as per the

architectural drawings and the directions of Engineer-

in-Charge. (Cost of aluminium snap beading shall be

paid in basic item.)

CIVIL Page 13 of 29

JSR DSR NON

SCH

JSR DSR NON SCH

Total

Quantity


a) DSR

21.3.2

With float glass panes of 5.50 mm thickness 50 sqm 673.55 0.00 33677.50 0.00

b) DSR

21.3.1

With float glass panes of 4.0 mm thickness 10 SQM 554.95 0.00 5549.50 0.00

A96 DSR.21.2 Providing and fixing 12 mm thick prelaminated

particle board flat pressed three layer or graded wood

particle board conforming to IS : 12833 Grade L Type

II, in panelling fixed in aluminium doors, windows

shutters and partition frames with C.P.Brass / stainless

steel screws etc. complete as per architectural

drawings and directions of engineer-in-charge

DSR

21.2.2

Prelaminated particle board with decorative lamination

on one side and balancing lamination on both sides.

5 sqm 812.60 0.00 4063.00 0.00

A97 DSR 21.4 Providing and fixing double action hydraulic floor

spring of approved brand and manufacture IS : 6315

marked for doors including cost of cutting floors as

required embedding in floors and cover plates with

brass pivot and single piece M.S. sheet outer box with

side plate etc. complete as per the direction of engineer-

in-charge.

DSR

21.4.1

With stainless steel cover plate 8 each 1733.50 0.00 13868.00 0.00

A98 non sch Supplying and fixing ISI mark flush Aluminium door

lock (75mm ,without handle) with keys 6 levers,

suitable for aluminium doors including fitting and

fixing complete.

4 each 329.00 0.00 0.00 1316.00

A99 non sch Providing and laying terracota brick tile cladding

(Veneer work) of insill,lintel, coping and cladding wall

lining etc (Veneer) works over 25to 30 mmthick bed

of cement mortar of ration 1:2 (1 cement : 2

sand)including pointing in white cement mortar 1:2

(1white cement: 2 stonedust) with an admixture of

pigment matching the brick shade. The worksto

include the dash fasteners and cramps / MS angle

35X35 X5 mm as perdetails and specifications.The

brick tile to be done both in linearsurfaces and curved

surfaces at all heights and depths scaffoldingshuttering

all course patterns. The pointing to be weathered, the

tliesurface to be laquer finished.All complete as called

for as per drgspecs and instructon of EIC (please do

refer to the cladding elevationand detail for quoting for

the works, no extra claims will beentertained in order

to complete the work.Cement will be issued free of

cost from store, Contractor has to maketheir own

arrangement for transportation of the same from

storeto work site.

210 Sqmt 750.00 0.00 0.00 157500.00

A100 DSR 21.7 Providing and fixing machine moulded aluminium

covering of approved pattern & design made out of

machine cut aluminium sheet and machine holed for

receiving screws, over expansion joints on vertical

surfaces / ceilings with full threaded cadmium plated

steel screws 4 mm dia stem, 30 mm long and

aluminium washers 2 mm thick, 15 mm dia at a

staggered pitch of 200 mm centre to centre including

drilling holes in the receiving surface and providing

expandable plastic sleeves in holes etc. complete.

0.00 0.00 0.00

A101 DSR

21.7.1

nodised aluminium sheet 2.5 mm thick (anodised

transparent or dyed to required shade according the IS

1868, minimum anodic coating of grade AC 15)

800 kg 335.85 0.00 268680.00 0.00

CARRIAGE OF MATERIALS

A101 JR III/8 Bricks 8Km(1KM+7P) 840 1000 Nos 412.77 346916.67 0.00 0.00

A102 JR III/ 11 Stone chips 10 Km. 2559 M3 172.61 441788.39 0.00 0.00

A103 JR III/11 Sand 10Km 2417 M3 172.61 417248.43 0.00 0.00

A104 JR III/5 Stone Metal - 10 Km. 0 M3 188.06 0.00 0.00 0.00

52112104.82

DSR AMOUNT 7355918.58

NON DSR AMOUNT in ` 543126.00

JSR AMOUNT in `

CIVIL Page 14 of 29

Sl. No Item No Description of Items Total

Quantity

Unit JSR DSR NS JSR DSR NS

B1 JR.12.1.1.1 Earthwork in excavation (As per I.S.3114/1965 for

laying of different types and sizes of pipe so as to

give one meter average coverover the socket of pipe

with disposal of excavated earth within nitial lead

and lift as per specification and direction of

Engineer -in-charge

a) For classificatin of Soil item -A 85 Per M³ 30.00 2,550.00

b) For classification of soil item -B 20 Per M³ 40.00 800.00

B2 JR 12.1.1.2 Earth work in back filling the trenches after laying

differrent types and size of pipe with earth removed

during excavation within initial lead and lift as per

specification and direction of Engineer -in-Charge

(For Soil item - A & B) 20 Per M³ 25.00 500.00

B3 DSR 18.10 Providing and fixing GI pipes complete with GI

fittings and clamps including cutting and making

good the wall etc. ( internal wall )

Exposed on wall

a) DSR 18.10.1 15mm dia nominal bore 15 mtr 105.85 1,587.75

b) DSR 18.10.2 20mm dia nominal bore 145 mtr 133.85 19,408.25

c) DSR 18.10.3 25mm dia nominal bore 40 mtr 179.65 7,186.00

d) DSR 18.10.4 32mm dia nominal bore 160 mtr 226.10 36,176.00

e) DSR 18.10.5 40mm dia nominal bore 15 mtr 264.05 3,960.75

f) DSR 18.10.6 50mm dia nominal bore 10 mtr 342.90 3,429.00

B4 DSR 18.11 Concealed pipe including painting with anti

corrosive bitumastic paint , cutting chases and

making good the wall

a) DSR 18.11.1 15mm dia nominal bore 120 mtr 144.75 17,370.00

b) DSR 18.11.2 20mm dia nominal bore 250 mtr 170.15 42,537.50

B5 DSR 18.13 Making connection of GI distribution branch with

GI main of following sizes by providing and fixing

tee, including cutting and threating the pipes etc.

complete.

a) DSR 18.13.1 25 to 40 mm nominal bores 6 each 166.05 996.30

b) DSR 18.13.2 40 to 80 mm nominal bores 2 each 423.20 846.40

B6 DSR18.12 Providing and fixing GI pipes complete with GI

fittings including trenching and refilling etc. (

external work )

a) DSR18.12..7 65mm dia nominal bore 190 mtr 356.15 67,668.50

b) DSR18.12.8 80mm dia nominal bore 10 mtr 458.15 4,581.50

B7 NON-SCH. Providing and fixing C.P. Spreader of approved

quality conforming to IS standareds : 15mm

nominal bore 56 each 90.00 5040.00

B8 DSR 18.40 Painting GI pipes and fittings with two coats of anti-

corrosive bitumastic paint of approved quality.

a) 18.40.1 15mm diameter pipes 135 metre 2.60 351.00

b) 18.40.2 20mm diameter pipes 395 metre 3.05 1,204.75

c) 18.40.3 25mm diameter pipes 40 metre 3.90 156.00

d) 18.40.4 32mm dia diameter pipes 160 metre 4.55 728.00

e) 18.40.5 40mm dia diameter pipes 15 metre 5.20 78.00

f) 18.40.6 50mm dia diameter pipes 10 metre 6.10 61.00

g) 18.40.7 65mm dia diameter pipes 190 metre 7.50 1,425.00

h) 18.40.8 80 mm diametre pipe 10 metre 8.65

B9 JR12.1.5.1 Providing and fixing male ended 15mm dia brass

bib cock of approved quality (Wt. not less than

350gms) with extra socket all complete as per

specification and direction of E/I 65 Each 221.86 14,420.90

B10 JR12.1.5.4 Providing and fixing 15mm dia male ended C.I.

Plug cock (Wt. not less than 400gms ) of approved

quality with extra socket all complete as per


B11 JR12.1.5.5 Providing and fixing 15mm dia male ended C.I.

Push cock (Wt. not less than 400gms ) of approved

quality with extra socket all complete as per


B12 JR 12.1.6 Providing and fixing brass/ C.I. Stop cock of

approved quality all complete as per specification

and direction of E/I

Rate (in `) Amount (in `.)

SANITARY

SANITARY Page 15 of 29


Quantity



(A) BRASS STOP COCK

a) 15mm dia 25 Each 177.86 4,446.50

B13 JR 12.1.9 Providing and fixing 15mm dia and 45 cm long

P.V.C. connection pipe with heavy quality brass

coupling at both ends etc. all complete as per

specification and direction of Engineer -in-charge

120 Each 67.86 8,143.20

B14 JR 12.1.11 Providing and fixing 15mm size C.P. brass pillar

cock (Weight not less than 350gms) C.I. body brass

spindle pillar cock of approved quality as per

specification and direction of Engineer -in-charge

b) C.I. body brass spindle 65 Each 177.86 11,560.90

B15 JR 12.1.12 Providing and fixing Gun metal full way valve of

approved quality all complete as per specification

and direction if E/I

a) c) 25mm dia and weight not less than 500gms 2 Each 360.20 720.40

b) d) 32mm dia and weight not less than 700gms 4 Each 505.83 2,023.32

c) f) 50mm dia and weight not less than 1.50Kg 2 Each 1022.12 2,044.24

B16 DSR 18.17 Providing and fixing gun metal gate valve with CI

wheel of approved quality (screwed ends)

DSR 18.17.5 65mm nominal bore 4 each 831.75 3,327.00

DSR 18.17.5 80mm nominal bore 10 each 1369.25 13,692.50

B17 JR 12.1.16 Cutting drain width wise above G.L for laying GI

pipes and restoring with brick in cement mortar

(1:4) 12mm cement plaster in (1:4) with neat

cement punning as per specification and direction of

Engineer-in-charge 2 Each 41.66 83.32

B18 JR 12.1.17 Cutting chajja or cornice for laying G.I. pipe and

restoring the same with R.C.C. (1:2:4) brick work in

cement mortar (1:4) and cement plaster (1:4) as per

specification and direction of Engineer-in-charge

50 Each 40.56 2,028.00

B19 JR 12.1.18 Making holes in walls for laying G.I. pipes and

restoring the same after pipe laying as per


a) 125mm thick wall 75 Each 35.63 2,672.25

b) 250mm thick wall 24 Each 46.46 1,115.04

B20 JR 12.1.21 Supplying, fitting and fixing the following items

complete with all materials as specification and

direction of E/I

a) Glass shelf with C.P brass rail

ii) 450mm X 125mm 65 Each 243.27 15,812.55

b) Mirrors of 6 mm thick plate glass levelled edge

mirror including C.P. brass revolving fittings 3mm

ply wood board and C.P. hinges to fix with mirror

ii) 450mm X 300mm 65 Each 751.96 48,877.40

c)i) C.P. brass towel rail 20mmX600mm with

bracket container 25 Each 366.96 9,174.00

ii) C.P. brass soap dish container medium quality

with screw and hinges etc. 25 Each 109.07 2,726.75

B21 JR RATE OF

MATL. SL

NO.42 ( PAGE

37)

Polythene water storage tank of ISI

mark(e.g.Sintex/Sinter/Himgiri etc.) with cover and

locking system.

20000

per ltr

capacity 4.30 86,000.00

B22 JR 12.1.28 Supplying materials and labour for construction of

600X600X90mm stop cock chamber of brick

masonary with 125mm thick work of designation

75B in cement mortar (1:6) with 12mm thick

cement plaster in C.M. (1:6) on inside only having

50mm thick RCC cover having 12mm dia lifting

rings, 2nos stop cock chamber will rest over 80mm

thick P.C.c. (1:3:6) over one brick flat soling

including cost of earthwork, all complete job, as per

approved design specification and direction of E/I

4 Each 1156.52 4,626.08

SANITARY INSTALLATION



Quantity



B23 12.2.2 Supplying, fitting fixing 40mm high vitreous white

glazed earthen ware E.W.C. with 'p' trap of Parry

Hindustan or any other approved I.S.S. make

including fixing 15 litres C.I. mosquito proof low

down flushing cistern of approved make with

complete fittings with C.I. handle and R.S. or

brackets with telescopic flush pipe with brass

coupling and plumbers joints spindle stop cock of

approved quality weight not less than 450grams

15mm P.V.C. alkathene pipe 45cm long with brass

coupling at both ends and white /black plastic solid

state seal and lead of commander /cuckoo or other

I.S.S. make with hinges or screws etc. painting pipe

and cistern etc. with 2 coats of approved paint over

a coat of red oxide primer etc. all complete as per


(i) With "P" trap

b) 10. litres low level PVC. cistern 29 Each 2505.03 72,645.87

B24 JR 12.2.1 Supplying, fitting fixing vitreous white glazed

earthen ware I.W.C. of Parry Hindustan or any other

I.S.S. approved make with 100mm H.C.I. 'p' trap 15

litres C.I. pull and let go flushing cistern of names

or other I.S.S. equivalent make, complete with all

fittings, C.I. or C.C. brackets 32mm

alkathene/P.V.C. telescope flush, pipe about 2M

long with one brass coupling and clamps G.I. chain

and pull including supplying and fixing a pair of

vitreous white glazed earthenware footrest to be

fixed in floor 15mm CI body brass spindle stop cock

of weight not less than 50gm, 15mm P.V.C

connection pipe 450mm long and the pipe and

cistern with two coats of approved paint over a coat

of red oxide primer etc. all complete as per


(B) 510mm long

b) with 12.5Litre Low level C.I. cistern 16 Each 2604.58 41,673.28

B25 JR 12.2.3. Supplying, fitting and fixing flat back or angular

lipped front vitreous white glazed earthen ware

urinal of Hindustan "Parry" or any other approved

I.S.S. make with 5 litres capacity C.I. automatic

flushing cistern of reliance for any other I.S.S.

approved make with all fittings with C.I. or r.S.

brackets, standard size G.I. flush pipe with fitting

clamps, 15mm C.I. body brass spindle stop cock of

approved quality weight not less than 400grams,

15mm P.V.C. /Alkathene pipe 450mmlongwith

brass coupling at both ends and doing plumber

joints including painting of exposed part with two

coats of approved paint over a priming coat of red

oxide, cutting wall and floor, making good the same

etc. all complete as per specification and direction

of E/I)

a) Flat back or standing corner (600mmX350mm)

56 Each 2169.98 1,21,518.88

B26 JR 12.2.4 Supplying, fitting and fixing vitreous white glazes

earthen ware indian squating type 600 x 350mm

urinal plate of parry, Hindustan or any other I.S.S.

approved make with internal flushing rim, 100mm

white glazed earthenware channel about 1m long 5

litre capacity C.I. automatic flushing cistern of

reliance or any other approved make with fittings

R.S. or C.I. brachets 15mm and 45cm long PVC /

Alkathene pipe standard G.I. flush pipe for back and

front with spreader fittings and brass coupling etc.

15mm C.I. body brass spindle stop cock weight not

less than 450 grams. all complete including painting

of exposed parts with 2 coats of approved paint over

a coat of red oxide primer and cutting the wall and

floor and making good the same as per specification

and direction of E/I)

a)600 X 350 mm size (Large) 20 Each 2211.33 44,226.60



Quantity



B27 JR 12.2.5 Supplying, fitting and fixing vitreous white glazed

earthen ware wash hand basin of parry or Hindustan

or any other I.S.S. approved make supported on

painted C.I. or R.S. brackets 32mm C.I. brass waste,

15mm dia C.I. body brass spindle stop cock of

approved quality of weight not less than 350grams,

32mm P.V.C. waste pipe 750mm long with brass

coupling at one end and making plumber joints etc.

all complete as per specification and direction of E/I

65 Each 1343.42 87,322.30

B28 DSR18.52.1 Providing and fixing CP brass stop cock ( concealed

) of standard design and of approved make

conforming to IS: 8931 15mm nominal bore 56 each 262.55 14,702.80

B29 DSR18.53.1 Providing and fixing CP brass angle valve for basin

mixer and gyser point of approved quality

conforming to IS:8931 15mm nominal bore 110 each 347.65 38,241.50

B30 DSR 18.62 Providing and fixing PTMT Ball cock of approved

quality, colour and make complete with Epoxy

coated aluminium rod with L.P/H.P. H. D. plastic

ball

DSR 18.62.5 50 mm nominal bore, 242 mm long Weighing not

less than 1240 gms 45 each 1338.30 60,223.50

B31 JR 12.2.7 Supplying, fitting and fixing H.C.I. pipe with ear of

approved make confirming to 1729 incuding

supplying nails and bobins short pieces, cutting

loose collars, lead and yarn for making lead caulked

joints cutting pipes to size including earth work or

scaffolding where necessary etc. all complete as per


a) 100mm dia 750 Per M 538.23 4,03,672.50

b) 75mm dia 50 Per M 399.86 19,993.00

c) 50mm dia 30 Per M 305.62 9,168.60

B32 JR 12.2.8 Supplying and fixing H.C.I fittings of approved

make conforming to I.S.S. 1729 including supplyig

nails and bobines lead and yarn from making lead

caulked joints including earth work or providing

scaffolding as the case may be all complete as per


(A) H.C. I. single junction with door but without ear

except socket

i) 100mm dia (weight 10.5 Kg approx.) 54 Each 796.38 43,004.52

ii) 80mm dia (Weight 7 Kg) 24 Each 652.96 15,671.04

(B) H.C.I heel rest bend


(C) 100mm dia H.C.i "P" trap with anti syphonage

horn 28 Each 549.55 15,387.40

(D) H.C.I. double junction with door and ear


(G) H.C.I. Bend with door and ear


ii) 80mm dia (Weight 4.5 Kg approx) 12 Each 345.42 4,145.04

(J) Floor trap with gratings

a) 100mm dia 113 Each 384.55 43,454.15

(K) Norton patent H.C.I. Cowel


(L) H.C.I. Pass over

a) 100mm dia 24 Each 478.05 11,473.20

B33 JR 12.2.12 Supplying materials and labour for painting the

exposed H.C.I. pipes and fittings with 2 coats of

approved paint over a coat of red oxide primer etc.

all complete as per specification and direction of E/I

a) 50mm dia 30 Per M 12.69 380.70

b) 80mm dia 46 Per M 19.51 901.36

c) 100mm dia 596 Per M 23.41 13,945.34

SEWERAGE AND DRAINAGE



Quantity



B34 JR 12.3.8 Supplying materials and labours for constructing

inspection chamber of designation class 75B bricks

size 750mm deep, 600x450mm internal dimension

having 250mm wall thickness in cement mortar

(1:6) including 12mm cement plaster (1:4) with

punning on inside and cement plaster (1:6) with

600X475mm G.I. Cover with frame (weight not less

than 36kg) alongwith earth work in excavation and

80mm thick P.C.C. (1:3:6) in foundation and

refilling all complete as per specification and

direction of E/I

30 Each 4303.41 1,29,102.30

B35 DSR 19.27.1 Constructing brick masonry road gully chamber

50x45x60 cm with bricks of class designation 75 in

cement mortar 1:5 (1 cement : 5 coarse sand)

including 500x450mm precast R.C.C horizontal

grating with frame complete as per standard

design.With F.P.S. bricks6 each 2248.35 13,490.10



Quantity



B36 DSR-19.1 Providing , laying and jointing glazed stone ware

pipes grade 'A' with stiff mixture of cement mortar

in the proportion of 1:1 ( 1cement :1 fine sand )

including testing of joints etc .complete

19.1.2 150mm dia 250 mtr 151.65 37,912.50

19.1.5 250mm dia 20 mtr 342.85 6,857.00

B37 DSR-19.2 Providing and laying cement concrete 1:5:10 (

1cement : 5 coarse sand : 10 graded stone aggregate

40mm nominal size )all round SW pipes including

bed concrete as per standard design

DSR 19.2.2 150mm diameter SW pipe 170 mtr 405.05 68,858.50

19.2.5 250mm diameter SW pipe 15 mtr 546.00 8,190.00

B38 DSR 19.4 Providing and fixing square mouth SW gully trap

Grade A complete with CI grating brick masonry

chamber with water tight CI cover with frame of

300x300mm size (inside) the weight of cover to be

not less than 4.5kg and frame to be not less than

2.7Kg as per standard design.

DSR 19.4.3.1 180x150mm size P type with FPS bricks class

designation 75 9 each 1036.75 9,330.75

B39 DSR19.6 Providing and laying non pressure NP2 class (light

duty) RCC pipes with collars jointed with stiff

mixture of cement mortar in the proportion of 1:2 (1

cement : 2 fine sand) including testing of joints etc.

complete.

DSR 19.6.2 150mm dia R.C.C. pipe 60 mtr 202.85 12,171.00

B40 DSR 19.7 Constructing brick masonary manhole in cement

mortar masonry manhole in cement mortar 1:4 (1

cement : 4 coarse sand) R.C.C. slab with 1:2:4 mix

(1 cement : 2 coarse sand : 4 graded stone aggregate

20 mm nominal size), foundation concrete 1:4:8 mix

(1 cement : 4 coarse sand : 8 graded stone aggregate

40mm nominal size) inside plastering 12 mm thick

with cement mortar 1:3 (1 cement : 3 coarse sand)

finished with floating coat of neat cement and

making channels in cement concrete 1:2:4 (1 cement

: 2 coarse sand : 4 graded stone aggregate 20mm

nominal size) finished with a floating coat of neat

cement complete as per standard design:

B41 DSR 19.7.1.1 Inside size 90X80 cm and 45 cm deep including C.I.

cover with frame (light duty) 455 X 610 mm

internal dimensions total weight of cover and frame

to be not less than 38 kg (weight of cover 23 kg and

weight of frame 15 kg) 1 each 5383.70 5,383.70

B42 DSR 19.8.1 Extra for depth for manholes. For 90x80 Cm With

FPS bricks class designation 75 6.0 mtr 2654.00 15,924.00

B43 DSR 19.32.1 Making soak pit 2.5m diameter 3.0 m deep with 45

x 45 cm dry brick honey comb shaft with bricks of

class designation 75 and S.W drain pipe 100mm

diameter, 1.8m long complete as per standard

design : with FPS bricks 1 each 9938.60 9,938.60

B44 DSR 19.19.3.1 Providing and fixing in position pre-cast R.C.C.

manhole cover and frame of required shape and

approved quality - HD-20, Circular Shape 560mm

internal dia 3 each 1110.30 3,330.90

B45 DSR 19.15.1 Replacement M.S. foot rests including fixing in

manholes with 20X20X10 cm cement concrete

blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 20 mm nominal size) as per

standard design . With 20x20mm square bar)

12.00 each 149.85 1,798.20

1329063.85

DSR AMOUNT ` 533124.25

NON DSR AMOUNT ` 5040.00

JR SCH AMOUNT `


Sl. No SR CPWD 2007

No.

Description of Item Quantity Unit SR CPWD NON

SCH./JR

NS/JR

AMOUNT

SR CPWD

AMOUNT

C1 1.8 WGPVCP Copper point wiring in PVC conduit: Wiring for

light point/ fan pt./ exhaust fan pt./ call bell pt. with

1.5 sqmm FR PVC insulated copper conductor single

core cable in recessed PVC conduit, with piano type

switch, phenolic laminated sheet, suitable size MS

box and earthing point with 1.5 sqmm FR PVC

insulated copper conductor single core cable etc. as

required:

a. 1.8.1 Group A 300 Pt. 264.00 79,200.00

b 1.8.2 Group B 600 Pt. 305.00 1,83,000.00

c 1.8.3 Group C 350 Pt. 397.00 1,38,950.00

C2 1.14 WGPVCSB Circuit/ Sub-main wiring in PVC conduit: Wiring for

circuit/ sub-main wiring along with earth wire with

the following sizes of PVC insulated copper

conductor, single core cable in surface/ recessed

PVC conduit as required. (for 5 amp plug point

wiring in recessed).

1.14.1 2 x 1.5 sqmm + 1x 1.5 sqmm earth wire 4500 Meter 71.00 3,19,500.00

C3 1.29 LPACCPT Supply and fixing light plug point piano type

accessories: Supply and fixing metal box of

150mm x 75mm x 60mm deep (nominal size) on

surface or in recessed with suitable size phenolic

laminated sheet cover in the front including

providing and fixing 3pin 5/6 amp socket outlet and

5/6 amp piano type switch, connection painting etc.

as required.(For light plugs to be used only in non -

residential buildings)165 each 102.00 16,830.00

C4 1.12

WGPVCPP2

Power plug point wiring in PVC conduit (2 x

4sqmm): wiring for light/power plug with 2x4sqmm

FR PVC insulated copper conductor, single core

cable in surface/ recessed PVC conduit along with

1no.4 sqmm FR PVC insulated copper conductor

single core cable for loop earthing as required.

500 Meter 97.00 48,500.00

C5 1.14 WGPVCSB Circuit/ Sub-main wiring in PVC conduit: Wiring for

circuit/ sub-main wiring along with earth wire with

the following sizes of PVC insulated copper

conductor, single core cable in surface/ recessed

PVC conduit as required. (recessed). Other

than 5 Amps.

1.14.1 2 x 1.5 sqmm + 1x 1.5 sqmm earth wire 3500 Meter 71.00 2,48,500.00

1.14.10 4 x 6 sqmm + 2x 6 sqmm earth wire 350 Meter 207.00 72,450.00

C6 1.30 PPACCPT Supply and fixing metal box of 180mm x 100 mm x

60mm deep (nominal size) on surface or in recessed

with suitable size phenolic laminated sheet cover in

the front including providing and fixing 6pin 5/6 &

15/16 amps socket outlet and 15/16 amps piano type

switch, connection painting etc. as required.

20 each 161.00 3,220.00

C7 Supplying, fitting and fixing of the following

categories of light fittings.

a) N.Z.C. Rate 4'-40W Single box Fl fitting equivalent to TMC

55/136 of Philips or equivalent including 1 x 40w FL

Tube, starter, choke etc. 401 Each 615.80 246935.80

b) N.Z.C. Rate 2 x 4'-40W double box Fl fitting equivalent to TMC

55/236 of Philips or equivalent including 2 x 40w FL

Tube, starter, choke etc. 384 Each 872.60 335078.40

c) non-schedule 2 x 4'-40W double, FL. street light luminair

equivalent to TRC 33/236 HPF of Philips or

equivalent including 2 x 40w FL Tube, starter, choke

etc. 4 Each 1950.00 7800.00

Rate Amount

ELECTRICAL Page 21 of 29

d) non-schedule 2X18W recess mounting type low glare luminare

with P5 lovre suitable for 2X 18 W PLL lamp

eqivalent to Philips FBS/300/218 P5, including lamp

etc. complete. 3 Each 2740.00 8220.00

e) non-schedule 2X36W recess mounting type low glare luminare

with P5 lovre suitable for 2X 36 W PLL lamp

eqivalent to Philips FBS/300/236 P5 HPF.including

lamp etc. complete. 3 Each 4300.00 12900.00

C7A non-schedule Supplying and fixing decorative ceilling fitting

complete with 10" dia Al base plate, froasted glass

cover, glass batten holder, 60W lamp as required

24 Each 390.00 9360.00

C8 non-schedule Supplying and fixing decorative optical batten for

surface mounting compact TL fitting complete with

2X 18 W TLD lamp equivallent to TMC 500/218 of

Phillips 6 each 1085.00 6510.00

C9 non-schedule Supplying and fixing Decorative wall mounted PL

fittings complete with 11watt PLS lamp and ballast

similar to Phillips type FMC 300/111 (Phillips,

Crompton, Bajaj) 9 each 555.00 4995.00

C10 non-schedule Supplying and fixing street light luminaries similar to

Phillips type SRX 086/150 withn single piece deep

drawn AL housing with acrylic cover complete with

150 watt SV lamp and choke and 1.5m long 40mm

dia GI pipe with suitable bend and two sets of MS

clamp and bolt fixed on wall and painting etc.

complete as required. (Phillips, Crompton, Bajaj)

6 each 5230.00 31380.00

C11 D.G.S.D. Rate Supplying and Transportation of following categories

of ceiling fans/ exhaust fan complete with all

accessories like down rod, regulator etc.

a) D.G.S.D. Rate 56" sweep ceiling fan for AC-230V

operation.(Crompton Greaves, Khaitan, Polar, Usha,

ORTEM) 260 Each 994.14 258476.40

b) D.G.S.D. Rate 48" sweep ceiling fan for AC-230V

operation(Crompton Greaves, Khaitan, Polar, Usha,

ORTEM) 86 Each 917.12 78872.32

c) JSR Supplying of 12" dia 1400 rpm A.C heavy duty

exhaust fan complete with louvers etc. as required

(Polar, Crompton, Calcutta, Usha). 24 Each 1530.00 36720.00

d) non-schedule Supplying of 9" dia 1400 rpm A.C heavy duty

exhaust fan complete with louvers etc. as required

(Polar, Crompton, Calcutta, Usha). 9 Each 1450.00 13050.00

C12 1.38 CALLBELL Supplying & Fixing call bell /buzzer suitable for

DC/AC single phase, 230v complete as reqd. 7 Each 26.00 182.00

C13 non-schedule Supply and fixing 1.1KV grade PVC insulated and

sheathed armoured aluminium conductor cable of

following size cable either in trench or on surface

/recessed by cutting trenches and refiling the same

with shifted soil after laying the cable and providing

bricking protection.

a) 3.5 X 50 sq.mm 100 Metre 462.00 46200.00

b) 3.5X 35 sq.mm 270 Metre 350.00 94500.00

c) 4X 25 sq.mm 325 Metre 315.00 102375.00

d) 4X 16 sq.mm 530 Metre 250.00 132500.00

C14 non-schedule Supplying and fixing compression type brass gland

including finising the ends of PVC cable with AL

lugs with crimping joints along with all accessories

for the following size of PVCA AL cable.

a) 3.5 X 50 sq.mm 2 set 180.60 361.20

b) 3.5X 35 sq.mm 14 set 142.45 1994.30

c) 4X 25 sq.mm 32 set 120.45 3854.40

d) 4X 16 sq.mm 36 set 100.35 3612.60


C15 2.33 TPMCBDB Supplying and fixing following way, three pole and

neutral, sheet steel, MCB distribution board, 415

volts, on surface / recess, complete with tinned

copper busbars, neutral busbar, earth bar, detachable

gland plate, interconnections, phosphatized and

powder painted including earthing etc. as required,

without MCB/ RCCB/ Isolator. ( general LDB)

a) 2.33.4 4 way (4 + 12), double door, horizontal type. 12 Each 1311.00 15,732.00

b) 2.33.5 6 way (4 + 18), double door, horizontal type. 4 Each 1634.00 6,536.00

C15A 2.43

PWVTMCBDB

Supplying, installation, testing and commissioning of

surface / recessed mounting, vertical type, 415V, pre-

wired MCB distribution board of sheet steel,dust

protected, duly phosphetised and powder painted,

inclusive of 200A tinned Cu busbar, eath bar,

common nutral link, dinbar for mounting MCB's,

detachable gland/ knockout plate, and with built in

loose wire box and superior make terminal

connectors for all incoming and out going circuits,

duly pre-wired with adequate size of FR PVC

insulated Cu conductor upto the terminal connectors

/ nutral link and ready for installation of following

ways ( without MCB and incommer) as required

(Inside Lab).

2.43.5 4 way double door 6 Each 6717.00 40,302.00

C16 2.51 MCBB Supply and fixing 5amp. to 32 amp. rating 240V , 'B'

series, miniature circuit breaker forlighting and other

loads of following poles in existing MCB DB

complete with connections, testing and

commissioning etc. as required.

a) 2.51.1 Single pole 210 Each 86.00 18,060.00

C17 2.55 MCBTPIS Supplying and fixing following rating, four pole, 415

volts, isolator in existing MCB DB complete with

connections, testing and commissioning etc. as

required:

a) 2.55.1 40 amps 16 Each 345.00 5,520.00

b) 2.55.2 63 amps 1 Each 362.00 362.00

c) non schedule Tripple pole 63A 6 Each 1204.00 7224.00

d) non schedule Tripple pole 40A 24 Each 1043.00 25032.00

POWER DB & MCB FOR LAB

C18 2.43

PWVTMCBDB

Supplying, installation, testing and commissioning of

surface / recessed mounting, vertical type, 415V, pre-

wired MCB distribution board of sheet steel,dust

protected, duly phosphetised and powder painted,

inclusive of 200A tinned Cu busbar, eath bar,

common nutral link, dinbar for mounting MCB's,

detachable gland/ knockout plate, and with built in

loose wire box and superior make terminal

connectors for all incoming and out going circuits,

duly pre-wired with adequate size of FR PVC

insulated Cu conductor upto the terminal connectors

/ nutral link and ready for installation of following

ways ( without MCB and incommer) as required

(Inside Lab).

a) 2.43.5 4 way double door 11 Each 6717.00 73,887.00

b) 2.43.7 8 way double door 3 Each 10394.00 31,182.00

C18A 2.33 TPMCBDB Supplying and fixing following way, three pole and

neutral, sheet steel, MCB distribution board, 415

volts, on surface / recess, complete with tinned

copper busbars, neutral busbar, earth bar, detachable

gland plate, interconnections, phosphatized and

powder painted including earthing etc. as required,

without MCB/ RCCB/ Isolator. ( general LDB)

2.33.4 4 way (4 + 12), double door, horizontal type. 13 Each 1311.00 17,043.00

2.33.5 6 way (4 + 18), double door, horizontal type. 1 Each 1634.00 1,634.00


C19 non schedule Supplying, installation, testing and commissioning of

surface / recessed mounting vertical type

compartmentalised, 415V TPNMCBDB OF sheet

steel 1.6mm thick, dust protected, duly painted

inclusive of 200A tinned Cu busbar, eath bar, nutral

link, dinbar, detachable gland plate with incoming of

100A TPN MCCB ( 16KA) and out going circuits,

duly wired with adequate size of PVC insulated Cu

wire between busbar & MCBs as well as incommer

and upto the terminal connectors / nutral link of

following ways ( without MCB) (floor DB for Lab

power DB)

a) 4 way 7 Each 5810.00 40670.00

C20 non schedule Supplying, installation, testing and commissioning of

surface / recessed mounting vertical type

compartmentalised, 415V TPNMCBDB OF sheet

steel 1.6mm thick, dust protected, duly painted

inclusive of 200A tinned Cu busbar, eath bar, nutral

link, dinbar, detachable gland plate with incoming of

125A TPN MCCB ( 16KA) and out going circuits,

duly wired with adequate size of PVC insulated Cu

wire between busbar & MCBs as well as incommer

and upto the terminal connectors / nutral link of

following ways ( without MCB) (floor DB for Lab

power DB)

a) 4 way 1 Each 7220.00 7220.00

C21 2.51 MCBB Supply and fixing 5amp. to 32 amp. rating 240V , 'B'

series, miniature circuit breaker forlighting and other

loads of following poles in existing MCB DB

complete with connections, testing and

commissioning etc. as required.

a) 2.51.1 Single pole 288 Each 86.00 24,768.00

b) 2.51.3 Tripple pole 30 Each 273.00 8,190.00

c) non schedule Tripple pole and neutral 63A 28 Each 1575.00 44100.00

d) non schedule Tripple pole 63A 32 Each 1204.00 38528.00

C22 2.62

MCBDPSOC20

S/F 20A, 240V SPN MCB industrial socket outlet :

S/F 20A 240V SPN industrial type socket out let

with two pole and earth metal enclosed plug top

along with 20A C series SP MCB in sheet steel

enclosure on surface or in recess with chained metal

cover for the socket outlet and complete with

connection , testing and commissioning etc. as

required.60 Each 520.00 31,200.00

C23 2.64

MCBTPSOC30

S/F 30A TPN MCB industrial socket outlet : S/F 30A

400V TPN industrial type socket out let with four

pole and earth metal enclosed plug top along with

30A C series TP MCB in sheet steel enclosure on

surface or in recess with chained metal cover for the

socket outlet and complete with connection , testing

and commissioning etc. as required.

32 Each 1294.00 41,408.00

C24 1.5 WGSTLPP2 Wiring for light/power plug with 2x4sqmmFR PVC

insulated copper conductor, single core cable in

surface steel conduit along with 1no.4sqmm FR PVC

insulated copper conductor single core cable for loop

earthing as required3700 Meter 136.00 5,03,200.00

C25 1.30 PPACCPT Supply and fixing metal box of 180mm x 100 mm x

60mm deep (nominal size) on surface or in recessed

with suitable size phenolic laminated sheet cover in

the front including providing and fixing 6pin 5/6 &

15/16 amps socket outlet and 15/16 amps piano type

switch, connection painting etc. as required.

111 each 161.00 17,871.00


C26 1.7 WGSTLSB Copper sub main wiring in steel conduit: wiring for

sub-main wiring with the following size of PVC

insulated, copper conductor, single core cable in

surface steel conduit as required:

a) 1.7.10 4 x 6 sqmm + 2x 6 sqmm earth wire 650 Meter 258.00 1,67,700.00

C27 1.41 ITCFFSUR ITC fluroscent fitting directly on surface with copper

wiring: Installation, testing and commissioning of

prewired, flourescent fittings of all types complete

with all accessories and tube etc. directly on

ceiling/wall including connections with 1.5 sq.mm

FR PVC insulated, copper conductor, single core

cable and earthing etc. as required

208 Each 43.00 8,944.00

C28 1.42 ITCFFDR ITC fluroscent fitting with down rods and copper

wiring: Installation, testing and commissioning of

prewired, flourescent fittings of all types complete

with all accessories and tube etc. including supply

and fixing ball and socket arrangement, 2nos. down

rods of 20mm dia x 1.6mm thick steel conduit upto

30cm. length painting and wiring the down rod and

connection with 1.5sqmmfFR PVC insulated Cu

conducter single core cable and earthing etc. as

required.

600 Each 126.00 75,600.00

C29 1.43 EXTDR P/F extra down rod with copper wiring: Providing

and fixing extra conduit down rod of 20 mm dia. 2 X

10 cm length with 2 X 1.5 sq.mm FR PVC insulated

, copper conductor , single core cable including

painting etc. as required (Note: more than 5 cm

length shall be rounded to the nearest 10 cm. and 5

cm. or less shall be ignored).

1000 Each 17.00 17,000.00

C30 1.45 ITCCFFC Installation, testing and commissioning of ceiling fan

including wiring the downrod of standard length

(upto 30cm) with 1.5 sq.mm FR PVC insulated,

copper conductor, single core cable including P/F

phenolic laminated sheet cover on the fan box etc. as

reqd. 325 Each 68.00 22,100.00

C31 1.49 EXTPIP20 S/F extra down rod of 10cm length GI pipe 20mm dia

heavy gauge including painting etc. as required.

400 Each 14.00 5,600.00

C32 1.51

NUMFANFT

Numbering of ceiling fan/exhaust fan/FL fitting etc.

362 Each 10.00 3,620.00

C33 1.52 ITCEF450 Installation of exhaust fan upto 450mm sweep in the

existing opening, including making the hole to suit

the size of the above fan, making good the damage,

connections, testing, commissioning etc. as required.

37 Each 223.00 8,251.00

C34 1.54 LOUSHEF Fixing louvres /shutters for exhaust fan:Extra for

fixing the louvres /shutters complete with frames for

exhaust fans of all sizes 37 Each 65.00 2,405.00

C35 non schedule Fixing only out door street light type Fl / MV light

fitting complete with all accessories like S/F 40mm

dia GI pipe Class B 1.5m Av. Length having suitable

bend including S/F MS clamp, PVC Cu wire and

making connection including making good the

damages and painting etc.10 each 405.25 4052.50

C36 1.21pvccon Supply and fixing of following sizes of PVC conduit

along with the accessories in recessed including

painting incase of surface conduit, or cutting the wall

and making good the same in case of recessed

conduit as required:


a) 1.21.1 20 mm 500 Meter 41.00 20,500.00

b) 1.21.2 25 mm 100 Meter 47.00 4,700.00

C37 non schedule Providing and drawing two pair 0.5 ATC telephone

cable in the existing conduit including connection as

required 1000 Meter 25.00 25000.00

C38 non schedule Providing and fixing telephone socket out let in

100x100x 50 MS box recessed in wall with backelite

top cover including connection and making good the

damages 20 set 120.00 2400.00

C39 non schedule Providing and fixing telephone junction box of krone

type with MS enclosure including connection as

required.: 10 pair. 6 set 1000.00 6000.00

C40 non schedule Providing and installing LT (415V) cubical type floor

mounted, front operated with back door panel with

16SWG MS sheet enclosure with suitable rating,

colour coaded Al bus bar, powder coated painting,

interconnected with Cu lead with crimping lugs and

complete with the following equipments:

630A TPN MCCB, 35KA as incomer -1No

630A TPN Al colour coated busbar - 1set

Metering panel complete with 1No. 0 -500A

ammeter,1 No. 0-500V voltmeter, 1 No ASS, 1No

VSS ,3nos 5A slide lock fuse, 3Nos indicator lamp,

1No.96x96 sqmm flush mounted electronic energy

meter with lcd Display and 6 nos. 500/ 5A CTs.

125A TPN MCCB,25KA as outgoing -1No

100A TPN MCCB,25KA as outgoing -8Nos.

32A TPN MCB as outgoing -1Nos.

63A TPN MCB as outgoing -7Nos.

MCCB / MCB make - C&S /HPL- Moeller/ L&T/

meter -AE / CT-KAPPA / ASS /VSS-KAYCEE etc.

1 set 168500.00 168500.00

C41 2.71 DANPLMV Providing and fixing MV Danger notice plate of

200mm x 150mm made of mild steel, atleast 2mm

thick, and vitreous enamelled white on both sides

and with inscription in signal red colour on front side

as required.60 Each 68.00 4,080.00

C42 3.5 EARGIPL GI Earth Plate Electrode : Earthing with GI plate

600mm x 600mm x 6mm thick including accessories

and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc.

(but without charcoal or coke and salt complete) as

required.2 set 1585.00 3,170.00

C43 3.6 EARCUPL Copper Earth Plate Electrode : Earthing with Cu

earth plate 600mm x 600mm x 3mm thick including

accessories and providing masonry enclosure with

cover plate having locking arrangement and watering

pipe etc. (but without charcoal or coke and salt

complete) as required4 set 3263.00 13,052.00

C44 3.7

EARCHARPL

Salt /charcoal for plate earth electrode: Extra for

using charcoal and salt for G.I. copper plate earth

electrode as required 8 set 603.00 4,824.00

C45 3.19

EARGIWRSUR

Providing and fixing 6 SWG dia GI wire on surface

or in recess for loop earthing as required.

200 metre 24.00 4,800.00

C46 3.22

EARCUWRLO

Providing and fixing 4mm dia cu wire on surface or

in recess for loop earthing along with existing surface

/ recessed conduit/ sub-main wiring/ cables as

required 3000 metre 36.00 1,08,000.00


LIGHTNING CONDUCTORS

C47 4.2 LCFGI Providing and fixing of lightning conductor finial,

made of 25mm dia, 300mm long GI tube, having

single prong at top, with 85mm dia 6mm thick GI

base plate including holes etc. complete as required.

16 each 243.00 3,888.00

C48 4.7 LCGITSURH Providing and fixing GI tape 20mm x3mm thick on

parapet or surface of wall for lightning conductors as

required ( for horizontal run) 300 meter 31.00 9,300.00

C49 4.8 LCGITSURV Providing and fixing GI tape 20mm x3mm thick on

parapet or surface of wall for lightning conductors as

required ( for verticall run) 200 meter 43.00 8,600.00

C50 4.12 LCTJGI Providing and fixing testing joints, made of 20mm x

3mm thick GI strip, 125mm long with 4 Nos of GI

bolts nuts check nuts and spring washer complete as

required. 6 each 37.00 222.00

C51 3.5 EARGIPL GI Earth Plate Electrode : Earthing with GI plate

600mm x 600mm x 6mm thick including accessories

and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc.

(but without charcoal or coke and salt complete) as

required.6 set 1585.00 9,510.00

C52 3.7

EARCHARPL

Salt /charcoal for plate earth electrode: Extra for

using charcoal and salt for G.I. copper plate earth

electrode as required 6 set 603.00 3,618.00

SR CPWD AMOUNT Rs. 24,56,711.00

NON DSR AMOUNT Rs. 1804421.92

Total Rs. 42,61,132.92


SL DESCRIPTION UNIT QTY. RATE AMOUNT

No. (Rs.) (Rs.)

a) 9 ltrs. capacity Water CO2 No. 20 1,900.00 38,000.00

b) 5 Kgs. capacity ABC Powder. No. 20 2,500.00 50,000.00

c) 9 ltrs. capacity Foam. No. 2 1,950.00 3,900.00

d) 4.5 Kgs. capacity CO2 No. 4 7,900.00 31,600.00

Set 1 62,000.00 62,000.00

D7 non-schedule S.I.T.C. of Swinging Hose Reel complete with

20mm size X 33 Mtr. long Dunlop or equivalent

make rubber hose and ABS tripple purpose Nozzle

as per IS: 884.

a) Hose Reel Body fabricated from CRCA sheet &

powder coated. No. 11 4,050.00 44,550.00

b) Hose (IS: 12585) & Nozzle. No. 11 7,025.00 77,275.00

D10

non-schedule

S.I.T.C. of 63mm X 15 Mtr. long Hose as per IS:

8423, bounded with pair of Alloy Steel Coupling as

per IS: 903. No. 10 5,600.00 56,000.00

D11 non-schedule S.I.T.C. of C.I. Flanged Gate Valve as per IS: 14846, PN 1.0 :-

a) 50mm Nb. No. 2 6,750.00 13,500.00

(a) 100mm Nb. No. 2 8,640.00 17,280.00

(b) 50mm Nb. No. 2 6,000.00 12,000.00

D12 non-schedule S.I.T.C. of lever operated C.I. Wafer type Butter Fly

Valve as per IS: 13095, PN 1.0.

No. 5 2,540.00 12,700.00

D9 non-schedule S.I.T.C. of Alloy Steel Branch Pipe with 18mm dia

Nozzle as per IS: 903.

D8 non-schedule

No. 1 10,450.00 10,450.00

S.I.T.C. of 3-Way Fire Service Inlet of Alloy Steel

with inbuilt non-return valve as per IS: 904.

No. 5 7,670.00 38,350.00

D6 non-schedule S.I.T.C. of single headed oblique type Hydrant

Valve (Alloy Steel) as per IS: 5290 with PVC blank

cap.

Job 1 35,000.00 35,000.00

D5 non-schedule S.I.T.C. of power / control cabling between pump

motor & pump starter and push button station by

PVC insulated copper armoured cable complete

with all accessories including earthing by G.I. wire.

8,500.00

D4 non-schedule

Set 2 1,900.00 3,800.00

non-schedule

Set 1 8,500.00

D2 non-schedule

non-scheduleD3

D1

FIRE FIGHTING AND PREVENTION SYSTEM

S.I.T.C. (Supply, Installation, Testing &

Commissioning) of Portable Extinguisher, complete

in all respect i.e. with 1st charge of refill, mounting

bracket, etc.

S.I.T.C. of cubical type wall mounted DOL starter

suitable for above 1 no. pump set with one remote

push button station for start-stop and complete in all

respect.

S.I.T.C. of Pressure Gauge (100mm dial & 0 to

15Kg / Sq.cm) including necessary fittings & ball

valve.

S.I.T.C.of Electric Motor Driven Booster Pump set

of capacity 450 Lpm at 25 Mtr. head complete in all

respect i.e. comprising pump, 7.5 HP motor of 2900

rpm, pin bush type coupling, coupling guard,

FIRE Page 28 of 29

D13 non-schedule

S.I.T.C. of C.I. Flanged Non Return Valve as per

IS:5312, PN 1.0.

(a) 50mm Nb. No. 2 6,000.00 12,000.00

D14 non-schedule S.I.T.C.of GM. Screwed Valve.

a) 25mm Nb, Ball Valve as per IS: 778. No. 14 1,350.00 18,900.00

b) 25mm Nb Spring loaded Safety (Air Release) Valve.No. 3 1,510.00 4,530.00

a) 100mm Nb, M.S., Medium. Mtr. 150 1,350.00 2,02,500.00

b) 50mm Nb, M.S., Medium. Mtr. 125 850.00 1,06,250.00

c) 40mm Nb, M.S., Heavy Mtr. 60 800.00 48,000.00

d) 25mm Nb, M.S., Heavy Mtr. 35 600.00 21,000.00

D17 non-schedule S.I.T.C. of Photoluminescence nature board.

a) " EXIT " (150mm X 300mm). No. 12 950.00 11,400.00

b) " Arrow " (150mm X 150mm). No. 12 500.00 6,000.00

TOTAL 9,93,935.00

D18 non-schedule

No. 12 765.00 9,180.00

S.I.T.C. of " Fire Order " on acrylic shet (size 450 X

300mm appx.) by bright lettering.

D16 non-schedule S.I.T.C. of aboveground / underground piping

conforming to IS: 1239 with fitting, support, clamp

and treatment on outer surface by one coat of primer

& two coats of synthetic enamel red paint or by

D15 non-schedule

No. 11 3,570.00 39,270.00

S.I.T.C. of front glassed single door powder coated

M.S.Hose Box (16 X 18 Swg) of standard design to

accommodate one Branch Pipe with nozzle and 2

length of 63mm X 15 Mtr. long Hose.

FIRE Page 29 of 29

Documents

VOLUME III Price Bid/Bill of Quantity - Engineering … Bid/Bill of Quantity . NIT No. DLI/CON/684A/579 Dt. 02.08.2017 In figures In words In figures In words 1 Civil Works ( As per