Table of Contents Page 1

Legal Info and Returns Page 1A5 Buffer System Page 2The BCMGunfighter Charging Handle Page 3M14/M1A Modstock Page 4Improved Modstock Kits (IMOD) Page 5-6MUR Upper Receiver Page 7-8Enhanced Modstock (EMOD) Page 9-10VIS Upper Receiver System Page 11-12Scout Mount (Flash Light Mount) Page 13Single Attachment Sling Endplate Page 13Receiver Extensions and Adapters Page 14CASV Rail Systems Page 15-16Low-Profile Gas Blocks Page 17Sight Assemblies Page 18Accessories Page 19Rifle Modstock Kits Page 20ModPod (Bipod) Page 20Flash Suppressors Page 21Clothing and Collectibles Page 22

1

Vltor Weapon Systems3735 N. Romero RoadTucson, Arizona 85705Phone 520.408.1944

Fax 520.293.8807www.vltor.com

NOTE: The assembly or installation of firearm parts and components should only be performed by a qualified gunsmith or certified armorer.Vltor Weapons Systems is not responsible for any injury or damage resulting from the improper installation or use of our products.

Vltor Weapons Systems strongly supports your 2nd Amendment Right! We promote the safe handling and responsible ownership of firearms, andencourage everyone (no matter your level of experience) to participate in firearms training and education programs.

While the Federal Crime Bill of 1994 expired in 2004, some State and Local laws still prohibit the installation of collapsible stocks, flash suppressorsand possibly other items sold by Vltor Weapon Systems. It is the responsibility of the purchaser to ensure that the installation of any product is notprohibited in your area. All items defined by the National Firearms Act of 1934 (machine guns, short barreled rifles/shotguns, suppressors,destructive devices and any other weapon) will only be sold to a government agency or a properly licensed manufacturer or dealer. Sales of machineguns to an FFL/SOT holder require a Letter of Demonstration. Vltor will not manufacture or rebuild any firearm, receiver or serialized part foranother manufacturer, without a BATFE approved Letter of Variance.

Our Warranty and Return Policy is available on our website: www.vltor.comAll photos by Military Moron (www.militarymorons.com) or Stickman

Shop our online web store at

WWW.VLTORSTORE.COM

Find us on facebook at:www.facebook.com/vltorweaponsystems

And

Our complete catalog is available online, with real time inventory!

2

Vltor A5 Buffer& Recoil SystemThe unique design of the newbuffer and receiver extensiontube allow the A5 System toadapt a MilSpec EMOD Stock toany M16/AR15 rifle.

Tests show that the A5 Systemreduces the cyclic rate of the M4Carbine and lowers bolt carriervelocity; and recently, extensivetesting conducted on the M16A4proved that the A5 System was themost reliable and consistent stocksystem available for that platform!

The A5 Buffer and Recoil Assembly was developed byVltor Weapons for the specific needs of the U.S.Military. As the M16/AR15 series of rifles haveevolved into specialized configurations, such as theSPR, M4 and Mk 18, each of these designs uses a newcombination of barrel and gas-systems. Attempts touniversally use the standard collapsible stock on allplatforms - from M16A4 to the Mk18 - have provenunreliable at best.

The A5 Buffer and Recoil System takes a newapproach to this problem, providing a singlecollapsing stock and buffer system that can be usedon all current configurations of direct impingementsystems. The A5 System reduces cyclic rate on theshorter barreled rifles and maintains a much moreconsistent bolt velocity and rate of fire across allcurrent issue weapons based on the M16.

All models include a Vltor EMOD Stock. $235.95AEBK-A5B, Black EMOD AEBK-A5G, Foliage Green EMODAEBK-A5T, FDE/Tan EMOD

Note: In some applications, such as severely overpressured rifles, piston operated guns and normallysuppressed guns, a heavier buffer may be required.Please contact us for more information on these.A5H3, 6oz, Specialty Buffer $49.95A5H4, 7oz, Specialty Buffer $59.95

Government Agencies and Military Organizations areencouraged to contact Vltor regarding test data, contractpricing and availability of the A5 System.

3

5.56mm, AR15 Style Rifles $47.32BCM-GFH3 (Long Latch)BCM-GFH4 (Medium Latch)BCM-GFH5 (Short Latch)

BCMGUNFIGHTER CHaRGING HaNdlE

7.62mm, AR10 Style Rifles $57.95BCM-GFH3-762 (Long Latch)BCM-GFH4-762 (Medium Latch)BCM-GFH5-762 (Short Latch)

The AR15 platform has undergone some significant changes; and so has how we use it. The manualof arms and immediate action drills we use today, stress the conventional charging handle latch ina way the original designers could have never imagined. Think about it... “Mortor Drills” or “KickStarting” the charging handle for an FTE? Eventually, the latch or its roll pin will fail.

Vltor developed the Gunfighter charging handle for Bravo Company, specifically to address thisproblem. The Patent Pending design protects the latch from these forces, while offering the optionof a medium or long latch extension. Go ahead and put it to the test, you’ll find that the new BCMGunfighter series certainly lives up to the name.

4

Both the M14/M1A and the Mk14/EBR stocksare adjustable to five lengths of pull and thestock’s receiver extension is adjustable forelevation. The total elevation adjustment isup to one inch in height: in its lowest positionthe stock will allow the use of iron sights orthe stock can be raised up to one inch higherfor use with mounted optics.

Also available is a Vltor Stock Adapter for theMk14 Enhanced Battle Rifle. Kit includes aneasy to install adapter, grip and EMOD Stock.

All Models $414.95RE-EBR, Black KitRE-EBRT, FDE/Tan KitRE-EBRG, Foliage Green Kit

Note: The M14 Modstock Kit includes only themodified stock, pistol grip, stock extension tube andEMOD assembly.

The Mk14 EBR Stock Kit includes a replacementadapter, pistol grip, stock extension tube, EMOD Stockand all mounting hardware.

The cluster rail offered on the Springfield SOCOMrifles is made exclusively for Springfield Armory - allinquiries regarding the SOCOM Cluster Rail should beaddressed to Springfield at 800-680-6866.

All Models $514.95M1S-1E, Black with EMODM1S-1ET, FDE/Tan with EMOD

M1S-1EG, Foliage Green with EMODSome special application M14s may have difficultyfitting the Modstock. These models include: Match,Heavy Barrel, Additional/Improved Bedding Lug, M21and M25 type rifles. Please contact Vltor or a qualifiedGunsmith before purchasing. For select-fire guns,please specify this at time of order.

M14 & M1A

Modstocks

New Stock Adapterfor the Mk14 EBR!

The evolution of the original; after years of reliableservice, the Vltor Modstock has undergone designchanges prompted by feedback from real world use onranges, battlefields and patrols around the world.

Taking features from the Enhanced Modstock, the IMODhas been beefed up to be even stronger than theoriginal, the ergonomics have been improved and snaghazards even further minimized. The IMOD also featuresan integral rubber buttpad with increased negativecamber to make shouldering and holding the weaponmore positive; all while adding only a couple of ouncesto the design.

IMOD color options include current military colors suchas: Foliage Green, Flat Dark Earth (Tan) and Black. Allcolors are available in the original “Standard” model orour unique and battle proven “Clubfoot” configuration.

MilSpec Vs. CommercialNote: There are two common sizes of carbine receiver extensions on the market. The VltorImproved Modstock (IMOD) and the Enhanced Modstock (EMOD) are available for either size. Makesure that your stock and extension tube are the correct size:

MilSpec – The tube diameter for a military specification extension tube is 1.150 inch.

Commercial – The diameter of the commercial tubes is 1.170 inch.

Know the difference betweenClubfoot and Standard

Clubfoot version (left) has asquared off portion of thestock’s toe. This “Clubfoot”portion assists the shooterduring prone position shooting,using the support hand tosecure the stock against theshooter’s shoulder.

The Standard Version Modstock(right) was designed to mimicthe conventional and moretraditional MilSpec carbine andM4 Enhanced Stock.

5

IMOD: The Modstock Improved

6

IMOD Basic Kit - Includes stock body, buttpadand battery compartments. $99.95

AIB-MCB, MilSpec, Clubfoot, BlackAIB-MCG, MilSpec, Clubfoot, Foliage GreenAIB-MCT, MilSpec, Clubfoot, FDE/TanAIB-MSB, MilSpec, Standard, BlackAIB-MSG, MilSpec, Standard, Foliage GreenAIB-MST, MilSpec, Standard, FDE/TanAIB-CCB, Commercial, Clubfoot, BlackAIB-CCG, Commercial, Clubfoot, Foliage GreenAIB-CCT, Commercial, Clubfoot, FDE/TanAIB-CSB, Commercial, Standard, BlackAIB-CSG, Commercial, Standard, Foliage GreenAIB-CST, Commercial, Standard, FDE/Tan

IMOD Basic Combo Kit - Includes stock body,buttpad, battery compartments, receiverextension tube, buffer, spring, end plate andlock nut. $159.95

AIBK-MCB, MilSpec, Clubfoot, BlackAIBK-MCG, MilSpec, Clubfoot, Foliage GreenAIBK-MCT, MilSpec, Clubfoot, FDE/TanAIBK-MSB, MilSpec, Standard, BlackAIBK-MSG, MilSpec, Standard, Foliage GreenAIBK-MST, MilSpec, Standard, FDE/Tan

AIB-MCG

AIBK-MST

AIBK-MSG

AIB-MCT

1-866-468-5867www.vltor.com

The main benefit of the MUR is that it is dimensionally correct. Vltor ensures reliability andaccuracy of our production process by using precision machining equipment, thorough qualitycontrol inspections, and a 100% final check of all critical dimensions. When you own a Vltor MUR,you have the highest quality upper receiver available on the market today.

The Modular Upper Receiver (MUR) is a rigid MilSpec flat-top upper receiver made to fit allAR15/M16/M4 rifles and carbines. The MUR was developed to give the customer a MilSpeccorrect upper receiver with a thicker wall, making the MUR upper receiver a stronger platform.This more rigid upper receiver will increase accuracy and reliability, while extending the lifeof the interfacing components, such as the bolt carrier group and barrel assembly.

7

The MUR is made from a 7075 aircraft-grade aluminum forging. Prior to machining, the forgingis fully stress relieved, heat treated, aged twice and undergoes a proprietary cryogenictreatment. The MUR is precision machined and each part finished by hand. There is not a betterupper receiver available.

The MUR comes in two models: one with a Bolt-Assist/Shell-Deflector and the second with aShell Deflector only. Vltor offers the selection at the time of purchase, but does not offer aservice to exchange the Bolt Assist or Shell Deflector.

All MURs feature a MilStd-1913 scope mounting rail and come equipped with an Ejection-Port,

Dust Cover Door.

8

MUR-1S (Shell Deflector Only) - $179.95MUR-1A (Forward Assist & Shell Deflector) - $199.95

MUR: Modular Upper Receiver

WWW.VLTOR.COM 1-866-468-5867

9

The EMOD is based on the same rugged and practical design as the original Vltor Modstock withspecific features designed from lessons taken from the modern battlefield. The EMOD is the mostdurable and rugged collapsible stock available.

The EMOD is approximately one inch longer than the original Modstock, and with the rubber buttplate installed, is about a quarter of an inch longer than the CRANE SCB. The increased length of theEMOD is a major benefit when used on scoped rifles (SPR/DMR), increasing the available comb forany given length of pull.

The buttplate of the EMOD is slightly wider and longer at the toe than the regular M4 stock with anoticeable negative pitch, making transitions from the ready position feel much more natural. TheEMOD was given enough weight to help balance out the normally muzzle heavy feel associated withnegative pitch buttstocks.

The toe of the buttplate is rolled under, giving the EMOD a superior feel when the weapon is held inthe “out of pocket” heads-up hold. The buttplate is covered with a removable rubber buttpad thatis molded over a metal strike plate. The shape of the buttplate and the rubber buttpad give a solidstock purchase in all situations.

Basic EMOD Combo Kit $196.95EMOD Kit and receiver extension tube (milspeconly), buffer and spring, lock plate and nut.

AEBK-MB, Black, MilSpec shownAEBK-MT, FDE/Tan, MilSpecAEBK-MG, Foliage Green, MilSpec

Basic EMOD Kit $125.95EMOD stock, battery compartments, buttpad & strike plate.

AEB-CB, Black, CommercialAEB-CT, FDE/Tan, Commercial shownAEB-CG, Foliage Green, Commercial

AEB-MB, Black, MilSpecAEB-MT, FDE/Tan, MilSpecAEB-MG, Foliage Green, MilSpec

The EMOD features additional storage in the removable, waterproof side compartments andholds up to four CR123 or three AA batteries. There is also an additional weather proofcompartment in the clubfoot area of the stock, which is easily accessible and holds two AAbatteries or other small parts.

The EMOD is constructed from the finest materials and will stand up to the most ruggeddemands. The EMOD is available for either the standard MilSpec receiver extension tube, orfor the aftermarket “Commercial” size tube. Available colors include Black, Foliage Green and

Flat Dark Earth (Tan). The EMOD is only available in the Clubfoot model.

1-866-468-5867WWW.VLTOR.COM

EMOD: The Enhanced Modstock

10

VIS: Versatile Interface Structure

VIS Receiver SystemFrequently Asked Questions

Can I fit the gas block or a suppressor inside the VIShandguard section? Only a “low-profile” gas block will fit. There areno railed gas blocks or suppressors that will fit.

Does the VIS accept standard AR15-type barrelassemblies? The VIS uses standard AR15/M16 barrels with amodified barrel nut (included).

Can I get an assembled, complete VIS upper? Complete uppers are available through several ofour qualified dealers.

Is Vltor going to offer a VIS in 7.62 NATO?This is currently in development.

Does the VIS work with any of the gas pistonsystems?

This is currently in development.

11

The VIS System at a glance

VIS-1 Standard Carbine (7 inch)

14.5” Overall, 21.5 Ounces

VIS-2 Standard Midlength (9 inch)

16.5” Overall, 25.0 Ounces

VIS-2A Extended Midlength (10 inch)

17.5” Overall, 26.0 Ounces

VIS-3 Standard Rifle (12 inch)

19.875” Overall, 29.0 Ounces

WWW.VLTOR.COM 1-866-468-5867

The VIS features four Mil-Std-1913Picatinny rails: The top rail is onecontinuous rail, from the back of thereceiver section to the front of the VIS.The removable lower section allows forthe attachment of the M-203 grenadelauncher, as well as assists in cleaning andmaintenance.

VIS1 Carbine LengthVIS-1SK, Shell Deflector only - $574.95VIS-1AK, Bolt Assist with Shell Deflector - $599.95

VIS2 MidlengthVIS-2SK, Shell Deflector only - $604.95VIS-2AK, Bolt Assist with Shell Deflector - $629.95

VIS2A Extended MidlengthVIS-2ASK, Shell Deflector only - $624.95VIS-2AAK, Bolt Assist with Shell Deflector - $649.95

VIS3 Rifle LengthVIS-3SK, Shell Deflector only - $654.95VIS-3AK, Bolt Assist with Shell Deflector - $679.95

Each kit contains: Upper and Lower Assembly,Barrel Nut, Wrench and M203 index plate.

12

One of Vltor’s most innovative products is the Versatile Interface Structure (VIS) upper receiverassembly. The VIS is a polylithic upper receiver assembly that ties the normally individual receiverand handguard into a single, aggregate part. This combination overcomes many problems that areassociated with the traditional “two piece” design; most notably the greatly improved structuralstrength and repeatable accuracy. This affords the user all the benefits of a free-floating barrel androck-solid railed forend.

SASE-2HK Type Hook SASE-1

Sling Loop

1-866-468-5867WWW.VLTOR.COM

Single Attachment Sling Endplate (Ambidextrous)Made for right and left-handed operators, Vltor now offers an ambidextrous Single Attachment SlingEndplate (SASE). These sling plates are a direct replacement to your existing receiver endplate. Twomodels are available: one accepts a 1 1/4-inch slings and the other accepts an HK-type hook/carabiner.Choosing the right or left hand placement is easy. Simply install the indexing washer and screw whichinterfaces with the rear of the receiver.

Flashlight and Sling Mounts

Models Available:SASE-1 (1 ¼-inch sling)SASE-2 (HK-type Loop)

Retail Price $19.95

Offset Scout Mount. This Scout Mountoffsets sideways by 1.300 inches. Fitsflashlights widths 1.010 to 1.040 inches (CK-series and Nitrolon-series). Also available asa quick release, throw-lever mount.SM-OCG $59.95SMQ-OCG, Quick Release Model $84.95

Standard Scout Mount (shown)SM-E (E-series Scout Mount)Flashlights widths: 0.810 - 0.826 inchesSM-G (Nitrolon Series Scout Mount)Flashlights widths: 1.025 - 1.040 inchesSM-CK (CK-Series Scout Mount)Flashlights widths: 1.010 - 1.026 inchesAll Standard Mounts $34.95

Scout MountThe Scout Mount is a quick detachable rail mount for certain SureFire™ flashlights. Installation issimple and the mounting is solid. Scout Mounts are available for E-series (Executive), G-series(Nitrolon) and CK-series (Classic Knurled) SureFire™ flashlights.

13

14

Adapter and Pistol Gripare not included!

Storage Compartment Receiver ExtensionThis 5-position Receiver Extension was madespecifically for weapon adapters that accept aCAR15/M4 type receiver extension.

This extension features a watertight storagecompartment that is accessible from the rear. Thereceiver extension has a MilSpec outer profile and willonly accept MilSpec dimensioned buttstocks.

RE-2 (Tube and End Cap Only) $49.95

Vltor Five Position Receiver ExtensionsVltor Carbine/Collapsible Buttstocks will only fitMilSpec Receiver Extensions.

RE-1 (for M4 & CAR15 Series) $46.95RE-10 (AR10 Carbine Series) $49.95

AR10 Owners: The RE-10 extension will only work when using theArmalite AR-10B Operation Spring, part# EA1095 and AR10 CarbineBuffer, part# EC0120. The receiver extension has a MilSpec outer

profile and will only accept MilSpec dimensioned buttstocks.

AK47/AKM/AKS Stock Adapter and ExtensionThe Adapter and Extension Combo is a directreplacement for the standard fixed AK-type stock.With this adapter installed the user will have fivestock positions, a watertight storage compartmentaccessible from the rear, and an ambidextroussingle-point sling mount located near the firearm'sreceiver.

RE-47 $89.95

Note: This kit is the adapter/extension only, stockor QD sling-swivel not included. Will fit sheet metalAKM variants only (excluding the Yugo or the IraqiTabuk). The adapter uses a MilSpec extension tube.

Receiver Extensions and Adapters

The CASVThe CASV is one of the simplest railsystems to install, and doesn’t requiresany special installation tools. Eachhandguard assembly has a rigid,continuous rail section along the top, andcomes with a removable lower shield andremovable rail sections that allow theuser to install rail sections where needed.

The CASV-EL fits all M4 style carbines with a flat-top receiver and a carbine-length gas system. TheCASV-EL system will not work with Mid-length or Rifle length gas systems.

The CASV-M is designed for the popular mid-length gas system rifles. The area forward of the top railcan be filled with a short rail, or used to mount the optional flip-up sight assembly (see page 18). TheCASV-M will work with a Carbine Length gas system; however, a low profile gas block must be used.

CASV Mid-Length Handguards

CASV-M, Black $239.95CASV-MX, Black $189.95CASV-MT, FDE/Tan $239.95CASV-MTX, FDE/Tan $189.95CASV-MG, Foliage Green $239.95CASV-MGX, Foliage Green $189.95

CASV Carbine Length Handguards

CASV-EL, Black $239.95CASV-ELX, Black $189.95CASV-ELT, FDE/Tan $239.95CASV-ELTX, FDE/Tan $189.95CASV-ELG, Foliage Green $239.95

CASV-ELGX, Foliage Green $189.95

15

The FAL Rifle CASV - One of the newestadditions to the CASV line of handguards is thesystem designed for the ubiquitous FAL series ofrifles. The new CASV-FAL and CASV-FAS mountsolidly to the standard inch or metric FAL with ashort version for the carbine style FALs.

CASV-FAL, Long $325.95CASV-FALX, Long $275.95CASV-FAS, Short $299.95CASV-FASX, Short $249.95

The Step-Level CASV offers a forward rail that is stepped down to match the height of the standard flattop A4/M4 upper receiver rail, allowing the use of optical sighting devices that would normally sit toohigh for a usable co-witness with the weapon’s iron sights. The Step-Level CASV also allows for the useof a standard rail mounted front sight.

The CASV-S is designed for a Midlength gassystem and will work in any application wherethe weapon uses a MilSpec flat top receiverand 9” handguard system. The CASV-S willwork with a Carbine (7”) gas system, but willrequire the use of our low profile gas block.This system is also available for carbinelength gas systems with a conventional frontsight, as the CASV-ELS. The CASV-S and ELSare available in black only.

CASV-S, Mid-Length, Black $249.95CASV-SX, Mid-Length, Black $199.95CASV-ELS, Carbine, Black $249.95CASV-ELSX, Carbine, Black $199.95

NOTE!All CASV-EL, CASV-ELS, CASV-S and CASV-M kits come with two 2”, two 4” and one 6” rail sectionsand hardware. All “X-Series” CASVs come with only one 2” rail section and hardware!

The installation of this handguard does not require any modifications to the firearm except for theremoval of the sight tower sling swivel when installing the CASV-EL or ELS series of handguards.

The CASV series of handguards is under constant development. Currently, designs are being testedfor the HK 416 and the FN SCAR-L/H. For the latest availability and pricing, please check our website

at www.vltor.com or the web store at www.vltorstore.com.

16

17

Clamp On Models

Set Screw Models

1-866-468-5867www.vltor.com

Clamp On Models $65.95

0.625” BoreGB-1C, blackGB-1CS, silver

0.750” BoreGB-2C, blackGB-2CS, silver

Set Screw Models $58.95

0.625” BoreGB-1S, blackGB-1SS, silver

0.750” BoreGB-2S, blackGB-2SS, silver

Low Profile Gas Blocks

These low-profile gas blocks were designed mainly to be used when a rail system/hand guard ismounted over the entire gas system. These are slim enough to fit within most rail systems. Pleasecheck your application before ordering.

All Vltor Gas Blocks are made from 17-4PH stainless steel and offered with a dark matte black oxidefinish or with a matte silver blasting. Available for the following bore diameters: 0.625 and 0.750inch, and offered in “Clamp On” and “Double Set Screw” versions. Combination set screw and taperpin models are offered exclusively through Noveske Rifleworks.

Special order gas blocks with brand marking and OEM use are available, please contact Vltor directly.

Gas Blocks

Flip-Up Sight for the New CASV-Mshown on page 15 of this catalog.

Completely redesigned for 2010, the VST folding front sight and gas block is an all steel, flip-updesign, with a spring loaded detent. There is no lock; if hit, the sight will fold down rather thandamage a locking mechanism. The VST is precision machined from tool grade steel, yet only weighsabout a half of an ounce more than a standard A2 front sight tower.

The VST is currently available in a cross-bolt clamp or taper-pin design, with or without a stainlesssteel sling swivel insert. All models of the VST use a standard AK front sight post and come with anadjustment tool. Note: The taper pin VST sights require drilling of the sight and barrel to install.

The CASV-M Flip-Up Front SightMade exclusively for the New Mid-Length CASVHandguard, the New CASV-M Front Sight can beinstalled on the forward part of the CASV-MHandguard. When folded down, it sits no higherthan the Picatinny rail section. Truly a snag free,out-of-the-way, backup sight.

When deployed, the CASV-M front sight is thesame height as the standard “F Marked” frontsight base. The CASV-M Front Sight uses a stan-dard M16A1 five position front sight pin.

CAS-FS $69.95

Sight Assemblies

18

Vltor VST Front SIghts

VST-1C $225.00Clamp-on with QD Socket

VST-1P $225.00Taper pin with QD Socket

VST-2C $225.00Clamp-on without QD Socket

VST-2P $225.00Taper pin without QD Socket

Note: Taper-pin models do not comewith pins. Clamp-on models comewith all installation hardware.

Accessories & Miscellaneous

Quick Detachable Sling SwivelThis 1 ¼-inch large push-button sling swivel will attach to allModstock variants, the IMOD/EMOD, the AK47 Stock Adapter (RE-47), the M1A/M14 Stock Assembly as well as most commercial“Sling Swivel Sockets”. The QDS is made in the USA and is allstainless steel construction.

QDS $14.95

19

M249 Stock Adapter KitSpecifically designed to allow for theinstallation of a MilSpec collapsiblestock on the M249 and Mk46 series ofmachine guns.

The M249 Stock Adapter worksextremely well with the Vltor EMODstock and provides the operator with amore compact and adjustable stocksystem and the ability to use a quickdisconnect sling swivel at the 10 and 2o’clock positions.

RE-249 $249.00Military contract pricing available on request.

CASV Handguard Rail KitThis is the same MilSpec, Picatinny rail kitthat is included with our CASV Handguards.The kit includes: two 2” rails, two 4” rails,one 5” rail with all mounting hardware.

CASV-RAIL $69.95

20

M16A1 Length ModelsARM-1S, Standard, BlackARM-1C, Clubfoot, BlackARM-1ST, Standard, FDE/TanARM-1CT, Clubfoot, FDE/TanARM-1SG, Standard, Foliage GreenARM-1CG, Clubfoot, Foliage Green

M16A2 Length ModelsARM-2S, Standard, BlackARM-2C, Clubfoot, BlackARM-2CT, Clubfoot, FDE/ Tan ARM-2CG, Clubfoot, Foliage Green

All Models Retail: $119.95

Rifle Modstocks

The Rifle Length Modstock is a dual-purpose stock system which mounts to either a CarbineCollapsible Receiver Extension (MilSpec only) or the Rifle Length Receiver Extension. The stocksare offered in two sizes: M16A1 length and the 5/8-inch longer M16A2 length stock system.

Note: When mounted to an adjustable receiver extension tube the Rifle Modstock is legallyconsidered an adjustable stock!

Side Mounted Bipod (ModPod)Another Vltor innovation is the ModPod, a bipod assembly that mounts to the side of railed forends.The individual bipod leg attaches to the side rails, allowing the user to have an obstructed lowerrail, where most bipods normally mount. This design lowers the weapon’s center of gravity givingthe weapon a more secured stance. The ModPod legs rotate 360 degrees, locking every 90 degrees.The lock is a simple and silent push button for each leg. The ModPod also allows for the use of theM203 Grenade Launcher.

ModPod kits include two legs (left and right) andall of the mounting hardware is self contained.No small parts to lose when the bipod isremoved!

MP-1, Black $189.95

MP-1T, FDE/Tan $189.95

VC-1 Compensator

VC-A1 Compensator

VC-A2 Compensator

Vltor Long Model Compensators - $59.95VC-1, 223, thread 1/2-28VC-301, 308, thread 5/8-24VC-P90, for FN P-90 only

Vltor Short Model Compensators - $54.95VC-A1, 223, thread 1/2-28VC-A2, (closed bottom), 223, thread 1/2-28VC-65, 6.5mm, thread 9/16-24VC-302, 308, thread 5/8-24

Vltor also offers the unique five flute “star” designin a replacement unit for the conventionalAR15/M16. It is exactly the same size and shape asthe standard issue AR15/M16 flash suppressor.

Available in either A1 (open all around) or A2(closed bottom) designs, the Vltor series ofcompensators are available for all popular calibers.

Based on the M4K Flash Suppressor, the VC-1 is designed tofacilitate the mounting of devices that rely on the rearshoulder of the suppressor as a mounting surface (such as theGemtech HALO Suppressor). With conventional flashsuppressors, the crush/peel washer can interfere with theshoulder surface and cause unstable mounting of muzzledevices, often leading to loosening or improper alignment.The VC-1 provides a dedicated shoulder that is not affectedby the flash suppressor washer. The VC-1 is also manufacturedwith the correct 22 millimeter diameter body to allow for theuse of any NATO standard muzzle attachment. Also available

for 7.62 NATO applications is the VC-301 & 302.

The Vltor series of compensators are unique. During product development, the Vltor designerscompared the various types of flash hiders and compensators on the market, and decided to offer adual purpose product. The unique venting of the Vltor Compensators forms a hybrid muzzle devicethat serves as both a muzzle compensator and a flash suppressor. Muzzle control is greatly enhancedwhile shooting, while flash reduction is comparable to the current issue A2 flash suppressor.

Flash Suppressors

21

Vltor T-Shirts. Made of 100% quality cotton, these t-shirtsfeature the large Vltor “Sword” logo on the rear and theVltor “V” logo on the front. Available in men’s sizes: Mediumthru 3X-Large. Offered in Black, Tan and Green. Pleasespecify size and color when ordering.

Vltor T-Shirts $19.95

Vltor Polo Shirts. Our stylish polo shirts are made by 5.11Tactical. They are as rugged as they are sharp looking andthe embroidered Vltor “V” logo makes these shirts stand outin any situation. Available in Small thru 3X-Large in Black,Red or Grey. Please specify size and color when ordering.

Vltor Polo Shirts $37.99 ($41.79 for 3XL)

Vltor Flex-Fit™ Hats. A quality self-adjusting hat, availablein two sizes, features the large Vltor “V” logo on the frontand the Vltor “Sword” logo on the back. Available inSmall/Medium and Large/Extra-Large. Offered in Black, Tanand Red. Please specify size and color when ordering.

Vltor Flex-Fit™ Hats $24.95

The Vltor & TangoDown Warrior Poster. Vltor andTangoDown teamed together to bring our customers this highquality, full color poster that reflects the true spirit of theProfessional Warrior…

“Only the tools of the Warrior change; not his mindset”

Printed on heavy 18X24 inch poster stock with excellentphotography and art work from Military Morons, this posteris suitable for framing and display anywhere. Proudly displaythe finest tools, pure focus and intrepid nature of the modernwarrior. Poster is shipped in a protective cardboard tube,price includes standard shipping.

VAP-1 Warrior Poster $9.25

Clothing, Art & Collectibles

www.vltor.com 22

Vltor Weapon Systems3735 N. Romero Road

Tucson, AZ 85705866-468-5867

www.vltorstore.comwww.vltor.com

Complete Firearms and OEM Solutionsfrom Vltor Weapon Systems

2011 marks the first time that Vltor Weapons has offered commercialproduction firearms. Vltor’s new line of AR15 based Short Barreled Riflesand Carbines has set new standards for design, function and reliability.Dealers that are interested in handling this exciting new product lineshould contact Vltor directly - we are taking orders now.

Vltor Weapon Systems has once again raised the bar by developingcomplete Technical Data Packages for the foreign small arms that arecurrently being used on battlefields around the World.

Additionally, Vltor Weapons Consulting has partnered with some of thetop names in the firearms industry to assist with the design,development and advancement of the state of the art.

Government Agencies, Military Organizations, and qualified industryentities that are interested in the Vltor Weapon Systems ForeignWeapons Project or small arms consultation can contact Vltor WeaponSystems for more information.