Vive Maestro Wireless Dimmers and Switches SPEC (369904)syncmagento.grupoabsa.com/.../015619_MRF2S-6ANS-WH.pdf · Features • The Maestro Wireless ® solution provides dimming/ switching

RF Local Controls

® Specif icat ion Submittal page

Job Name:

Job Number:

Model Numbers:

ViveTM Designer-style: Maestro®

369904c 1 03.31.16

ViveT Maestro Wireless® Dimmers and SwitchesThe Maestro Wireless® solution incorporates Maestro Wireless® load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation.Maestro Wireless® dimmers and switches use Lutron® patented Clear Connect® RF Technology, which enables wireless communication with Radio Powr SavrTM sensors and Pico® remote controls for light control and general switched loads.

These products are also compatible with the ViveTM hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all ViveTM devices. The ViveTM hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the ViveTM hub, see specification submittal 369902. Note for Replacement: MRF2S - the “S” model can replace the non-”S” model.

Features• TheMaestroWireless® solution provides dimming/

switching of multiple load types, occupancy/vacancy sensing, daylight harvesting, and high-end trim.

• Lutron® patented Clear Connect® RF Technology works through walls and floors.

• IncorporatesadvancedfeaturessuchasfadeON / fade OFF, high-end trim, and rapid full-ON.

• ControlsincludeFrontAccessibleServiceSwitch(FASSTM) for safe lamp replacement.

• Two-wiredimmersandswitchesavailableforretrofitapplications.

• Powerfailurememory:Ifpowerisinterrupted,thecontrol will return to its previously set level prior to interruption.

Receiving DevicesMaestro Wireless® Controls

Neutral and Non-Neutral Dimmers

Neutral and Non-Neutral Switches

Transmitting DevicesRadio Powr SavrTM Sensors

Pico® Remote Controls

Ceiling-Mounted Occupancy and Vacancy Sensors

Wall-Mounted Occupancy and Vacancy Sensors

Daylight Sensors

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 2 03.31.16

Maestro Wireless® Dimmers

Models AvailableDimmersCFL / LED/Halogen / Incandescent / Magnetic Low-VoltageMRF2S-6CL-XX 1 150 W CFL / LED Dimmer; 600W/600VAIncandescent/MLVDimmer120V~

Electronic Low Voltage DimmerMRF2S-6ELV120-XX1 600 W ELV Dimmer 120 V~ (neutral required)

Companion DimmersClaro® Gloss FinishesMA-R-XX1,2 Companion Dimmer 120 V~

MA-R-277-XX1,2 CompanionDimmer277V~

Satin Colors® Satin FinishesMSC-AD-XX1 Companion Dimmer 120 V~

MSC-AD-277-XX1 CompanionDimmer277V~

1 “XX” in the model number represents color / finish code. See Colors and Finishes at end of document.2 BAA-compliantmodelnumbersavailable.Adda“U”prefixtothemodelnumber.

Dimmer

Companion Dimmer

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 3 03.31.16

Ganging and DeratingWhen combining controls in the same wallbox, derating is required (see Load Type and Capacity tables). Dimmer Load Type and Capacity

No Neutral RequiredA B B B C B

Control Voltage Load Type Minimum LoadMaximum Load

A: Not Ganged B: End of Gang C: Middle of Gang

MRF2S-6CL 1,2 120 V~CFL / LED, Incandescent 50 W (see lamp list) See Mixing Lamp Types, page 4MLV 2 50W/VA 450W/600VA 400W/500VA 300W/400VA

Note: do not mix ELV and MLV load types on a single control.1 DimmerLoadType:

• MRF2S-6CLisdesignedforusewithpermanently-installedincandescent,CFL,LED,ortungstenhalogenonly.2 Low-VoltageApplications:

• UseMRF2S-6CLwithmagnetic(coreandcoil)low-voltagetransformersonly.Notforusewithelectronic(solid-state)low-voltagetransformers.

Mixing Lamp TypesMixing lamp types (using a combination of CFL / LED, and Incandescent / Halogen bulbs) and ganging with other dimmers or electronic switches may reduce maximum wattage, as shown.Example:Iffinsfromonesideofdimmer are removed and you have two 24 W bulbs installed (total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

Do not remove outside fins on ends of ganged controls (shaded areas below)

A B B B C B

Total CFL/LED WattageTotal Incandescent/Halogen Wattage


MRF2S-6CL0 W + 50 W – 600 W Or 50 W – 500 W Or 50 W – 400 W1 W – 25 W + 0 W – 500 W Or 0 W – 400 W Or 0 W – 300 W26 W – 50 W + 0 W – 400 W Or 0 W – 300 W Or 0 W – 200 W51W–75W + 0 W – 300 W Or 0 W – 200 W Or 0 W – 100 W76W–100W + 0 W – 200 W Or 0 W – 100 W Or 0 W – 50 W101 W – 125 W + 0 W – 100 W Or 0 W – 50 W Or 0 W126 W – 150 W + 0 W Or 0 W Or 0 W

Maximum LoadTotal MLV Wattage 450W/600VA 400W/500VA 300W/400VA

Example If a dimmer is installed in location “B” above and there are two 24 W CFL bulbs installed (Total CFL Wattage = 48 W), you may add up to 300 W of incandescent or halogen lighting.

Neutral RequiredA B B B C B



MRF2S-6ELV 120 V~ ELV 5 W 600 W 500 W 400 W

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 4 03.31.16

Maestro Wireless® Switches

Models AvailableSwitchesLighting and motor loadsMRF2S-6ANS-XX1,2,4 6ALighting/3AFan(1/10HPmotor), Electronic Switch 120 V~

MRF2S-8ANS120-XX1,2,4 8ALighting,5.8AFan(1/4HPmotor),Spec-Grade Electronic Switch 120 V~

MRF2S-8S-DV-XX 2,3,4 8ALighting,3AFan(1/10HPmotor,120V~ only), Spec-GradeElectronicSwitch120–277V~, no neutral wire required

Companion SwitchesClaro® Gloss FinishesMA-AS-XX2,4 Companion Switch 120 V~

MA-AS-277-XX2,4 CompanionSwitch277V~

Satin Colors® Satin FinishesMSC-AS-XX4 Companion Switch 120 V~

MSC-AS-277-XX4 CompanionSwitch277V~

1 Neutral wire required.

2 BAA-compliantmodelnumbersavailable.Adda“U”prefixtothemodelnumber.

3 MayrequireLUT-MLC(includedwithMRF2S-8S-DVmodels)toensureproperfunctionwithlow-wattageloadtypes. See page 12 for details.

4 “XX” in the model number represents color / finish code. See Colors and Finishes at end of document.

Switch

Companion Switch

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 5 03.31.16

Switch Load Type and Capacity

No Neutral RequiredA B B B C B



MRF2S-8S-DV 1,5

120–277V~ Incandescent/Halogen 25 W 8A 8A/7A4 7A120–277V~ Fluorescent/LED/CFL 40W(LUT-MLC)3 8A 8A/7A4 7A120 V~ Fan Motor 0.4A 1/10HP(3A) 1/10HP(3A) 1/10HP(3A)

1 SwitchLoadType:• MRF2S-8ANS120isdesignedforusewithpermanently-installedlightingloadsandwithfanmotorloadsupto1/4HP(5.8A).

• MRF2S-8S-DVisdesignedforusewithpermanently-installedlightingloadsandwithfanmotorloadsupto1/10HP(3A,120V~ only).

• MRF2-6ANSisdesignedforusewithpermanently-installedlightingloadsandwithfanmotorloadsupto1/10HP(3A).

2 Forloadslargerthan8A(120V~),theMRF2S-8ANS120switchcanbeusedwiththePHPM-SW-DV-WHpowerbooster.

3 TheLUT-MLCensuresproperfunctionwithlow-wattagefluorescent,CFL,andLEDloadtypes.See page 12 for details.

4 Maximumloadfordouble-gangapplicationis8A.Triple-gangapplicationderatesmaximumloadto7A.

5 BAA-compliantmodelnumbersavailable.Adda“U”prefixtothemodelnumber.

Neutral Required

Do not remove outside fins on ends of ganged controls (shaded areas below)

A B B B C B



MRF2S-8ANS1201,2,5 120 V~Lighting 25 W 8A 6.5A 5AFan Motor 0.2A 1/4HP(5.8A) 1/4HP(5.8A) 1/6HP(4.4A)

MRF2-6ANS1 120 V~Lighting 25 W 6A 5A 3.5AFan Motor 0.2A 1/10HP(3A) 1/10HP(3A) 1/10HP(3A)

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 6 03.31.16

SpecificationsRegulatory Approvals

• UL® Listed.• cUL® Listed (MRF2S-6CL only).• CSACertified(exceptforMRF2S-6CL).• FCCApproved.ComplieswiththelimitsforaClassB

digital device, pursuant to Part 15 of the FCC Rules.• IndustryCanadaCertified.• Thefollowingmodelnumbershavebeentestedand

foundcompliantwithUL2043foruseinairhandlingspaces:MRF2S-6CL-GR

PowerOperatingvoltage:

• 120V~ 50/60 Hz (all models)• 277V~ 50/60 Hz (MRF2S-8S-DV)

Environment• Ambientoperatingtemperature:32°Fto104°F

(0 °Cto40°C)• 0%to90%humidity,non-condensing.• Indooruseonly.

Key Design FeaturesDimmers

• Onasingle-tap,lightsfadeUPorDOWN.• Onadouble-tap,lightsgotofullON.• WhenON,pressandholdtoengage20-secondfade

to OFF.• Lightlevelscanbefine-tunedbypressingand

holding the dimming rocker until the desired light level is reached.

• Two-wiredimmersavailable.

Switches• Onasingle-tap,lightsturnONorOFF.• Two-wireswitchesavailable.

All RF Local Controls• Testedtowithstandelectrostaticdischargewithout

damage or memory loss, in accordance with IEC 61000-4-2.

• Testedtowithstandsurgevoltageswithout damage or loss of operation, in accordance with IEEE C62.41-1991 Recommended Practice on SurgeVoltagesinLow-VoltageACPowerCircuits.

• Controlsalwaysoperatelocallyanddonotrequiresystem control.

• Powerfailurememory:shouldpowerbeinterrupted,the control will return to its previously-set level prior to the interruption when power is restored.

• Usesconventional3-wayand4-waywiring.• MultiplelocationcontrolfromDimmer/Switchandup

to nine Companion Dimmers / Switches.• UseLutron® Designer (Claro® and Satin Colors®)

wallplates or designer-style wallplates from other manufacturers. Wallplates are sold separately.

• Lutron® Claro® and Satin Colors® wallplates snap on with no visible means of attachment.

• Requiresaone-gangU.S.wallbox;31⁄2 in (89 mm) deep recommended, 21⁄4in(57mm)deepminimum.

• Greenindicatorlights.

System Communications and Capacity• MaestroWireless® controls communicate with the

Pico® remote controls and Radio Power SavrTM sensors through radio frequency (RF).

•Receiveswirelessinputsfromupto10Pico® remote controls, 10 Radio Powr SavrTM occupancy / vacancy sensors, and 1 Radio Powr SavrTM daylight sensor

• MaestroWireless® local controls must be located within 60 ft (18 m) line-of-sight or 30 ft (9 m) through walls, of Radio Power SavrTM sensors.

• MaestroWireless® local controls must be located within 60 ft (18 m) line-of-sight or 30 ft (9 m) through walls, of a Pico® remote control.

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c703.31.16

WallplateAdapter/Wallplatepurchasedseparately

WallplateAdapter Wallplate

Wallbox

Control

AdapterMountingScrews

Control Mounting Screws

Mounting

DimensionsAlldimensionsareshownas:in(mm)

Side View

5/16(8)

1 1⁄8(30)

Front View

4 11⁄16(119)

2 15⁄16(75)

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 8 03.31.16

Operation

Status LEDsIndicate light level; glow softly as night light when light is OFF

Dimming RockerPress to brightenPress to dim

TapswitchTap ON / OFF;Double-tap:lightsgotofullON

FASSTM

FrontAccessibleServiceSwitchFASSTM

FrontAccessibleServiceSwitch

FASSTM Front Accessible Service SwitchImportant Notice: To service load, removepowerbypullingtheFASSTM out completely on either the Dimmer / Switch orCompanionDimmer/Switch.Afterservicingload,pushtheFASSTM back in fully to restore power to the control.

Dimmer

TapswitchTap ON / OFF

SwitchStatus LEDIndicates load status; glows softly as night light when light is OFF

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 9 03.31.16

1 When using controls in single location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring or to ground.

2 UptonineMaestro® Companion Dimmers may be connected to the Maestro Wireless®Dimmer.Totalblueterminalwirelengthmaybeupto250ft(76m).

Wiring DiagramsSingle-Location Dimmer Installation without NeutralMRF2S-6CL

Dimmer

Load

Brass

Black

Line / Hot

Green

Blue 1

Ground

Neutral

120 V~ 60 Hz

Multi-Location Dimmer Installation without Neutral 2MRF2S-6CLwithMA-R/MSC-AD

Companion Dimmer Companion Dimmer Dimmer

BrassBrassBrass

BlackBlackBlack

Line / Hot

GreenGreenGreen

BlueBlueBlue

GroundGroundGround

Neutral

120 V~ 60 Hz Load

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 10 03.31.16

1 When using controls in single location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring or to ground.

2 UptonineMaestro® Companion Dimmers / Switches may be connected to the Maestro Wireless® Dimmer / Switch. Total blue terminal wire length may be up to250ft(76m).

3 Neutral-wire Dimmers / Switches must be connected on the Load side of a multi-location installation.

Wiring Diagrams (continued)

Multi-Location Switch Installation with Neutral 2,3

MRF2S-6ELV120,-8ANS120,and-6ANSwithMA-AS/MSC-AS

Companion Dimmer / Switch

Companion Dimmer / Switch Dimmer / Switch

Brass

Silver

BrassBrass

BlackBlackBlack

Line / Hot

GreenGreenGreen

BlueBlueBlue

GroundGroundGround

Neutral

120 V~ 60 Hz Load

Single-Location Switch Installation with NeutralMRF2S-6ELV120,-8ANS120,and-6ANS

Dimmer/Switch

Load

Brass

Black

Silver

Line / Hot

Green

Blue 1

Ground

Neutral

120 V~ 60 Hz

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 11 03.31.16

1 ALUT-MLCensuresproperfunctionwhenfluorescent,CFL,orLEDloadsareused.InstalltheLUT-MLCinsidealoadfixtureorinaseparateJ-boxwithinthecircuit.

2 When using controls in single-location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring or to ground.

3 UptonineMaestro® Companion Switches may be connected to the Maestro Wireless®Switch.Totalblueterminalwirelengthmaybeupto250ft(76m).4 RequiresMA-AS/MSC-ASfor120V~applications,andMA-AS-277/MSC-AS-277for277V~ applications.

Single-Location Switch Installation with LUT-MLC 1MRF2S-8S-DV

Switch

Load LUT-MLC1

Brass

Black

Line / Hot

Green

Optional *

Blue 2

Ground

Neutral

120 V~ 60 Hz or 277V~ 60 Hz

Multi-Location Switch Installation with LUT-MLC 1,2,3

MRF2S-8S-DVwithMA-AS/MA-AS-277orMSC-AS/MSC-AS-2774

Companion Switch Companion Switch Switch

BrassBrassBrass

BlackBlackBlack

Line / Hot

GreenGreenGreen

BlueBlueBlue

GroundGroundGround

Neutral

120 V~ 60 Hz or 277V~ 60 Hz

Load LUT-MLC1

Optional *


* Optional Procedure: UsingLUT-MLCwithMRF2S-8S-DV-XX

•InstallMRF2S-8S-DV-XXfirstwithoutLUT-MLCtoseeif required. Check for problems with load.

•Problemscanoccurwhenlow-wattageloadsareused (< 40 W).

•WatchforflickeringloadswhendimmerisinelectronicOFF state.

•Ifrequired,LUT-MLCcanbeinstalledbetweenswitched hot and neutral in wallbox if neutral is present, or in any fixture on the switched circuit.

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 12 03.31.16

1 When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring or to ground.2 UptonineMaestro® Companion Switches may be connected to the Maestro Wireless®Switch.Totalblueterminalwirelengthmaybeupto250ft(76m).3 Neutral-wire Switches must be connected on the Load side of a multi-location installation.


Single-Location Switch Installation with Power Booster Single FeedMRF2S-8ANS120and-6ANSwithPHPM-SW-DV-WH

Switch

Brass Blue 1

Zone In

Black

Silver

Line / Hot

Switched Line / Hot

Line / Hot

NeutralNeutral

Neutral

Ground

Ground

Green

120 V~ 60 Hz

Load

Multi-Location Switch Installation with Power Booster Single Feed 2,3

MRF2S-8ANS120and-6ANSwithMA-AS/MSC-ASandPHPM-SW-DV-WH

Companion Switch Switch

Brass BlueBlue

Zone In

Black

Silver

Line / Hot

Switched Line / Hot

Line / Hot

Brass

Black

NeutralNeutral

Neutral

Ground

Ground

Green

Ground

Green

120 V~ 60 Hz

Load

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 13 03.31.16

Multi-Location Switch Installation with Power Booster Dual Feed 1,2

MRF2S-8ANS120and-6ANSwithMA-AS/MSC-ASandPHPM-SW-DV-WH

Companion Switch Switch

Brass BlueBlue

Zone In

Black

Silver

Line / Hot

Switched Line / Hot

Line / Hot

Brass

Black

NeutralNeutral

Neutral

Neutral

Ground

Ground

Green

Ground

Green

120 V~ 60 Hz or 277V~ 60 Hz

120 V~ 60 Hz

Load


Single-Location Switch Installation with Power Booster Dual FeedMRF2S-8ANS120and-6ANSwithPHPM-SW-DV-WH

Switch

Brass Blue 1

Zone In

Black

Silver

Line / Hot

Switched Line / Hot

Line / Hot

NeutralNeutral

Neutral

Neutral

Ground

Ground

Green

120 V~ 60 Hz or 277V~ 60 Hz

120 V~ 60 Hz

Load

1 When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring or to ground.2 UptonineMaestro® Companion Switches may be connected to the Maestro Wireless®Switch.Totalblueterminalwirelengthmaybeupto250ft(76m).3 Neutral-wire Switches must be connected on the Load side of a multi-location installation.

RF Local Controls


Job Name:

Job Number:

Model Numbers:


369904c 14 03.31.16

Colors and Finishes

Gloss Finishes Satin Finishes

Metal Finish (wallplate only)

Stainless Steel SS

Taupe TP

Turquoise TQ

Plum PL

Merlot MR

Terracotta TC

Sienna SI

Midnight MN

Hot HT

Desert Stone DS

Eggshell ES

Biscuit BI

Snow SW

Palladium PD

Greenbriar GB

Bluestone BG

Mocha Stone MS

Goldstone GS

Stone ST

Limestone LS

White WH

Ivory IV

Almond AL

LightAlmond LA

Gray GR

Brown BR

Black BL

• Duetoprintinglimitations,colorsand finishes shown cannot be guaranteed to perfectly match actual product colors.

• Colorchipkeychainsareavailableformoreprecisecolormatching: GlossFinishes:DG-CK-1 SatinFinishes:SC-CK-1

When using Stainless Steel wallplates, it is recommended that you order the dimmer/switch in Midnight (MN).

Documents

Vive Maestro Wireless Dimmers and Switches SPEC (369904)syncmagento.grupoabsa.com/.../015619_MRF2S-6ANS-WH.pdf · Features • The Maestro Wireless ® solution provides dimming/ switching