Upload
phamkhue
View
219
Download
2
Embed Size (px)
Citation preview
AwningDouble HungSliding
135º Bay Window
90º Bay Window
Sliding Fixed Lite
Transom Window
Casement
Louvre Bi-fold
Rake Circle Arch
Window and Door Information
n All diagrams shown as viewed from the exterior
n Non standard frame sizes are available on request
n All measurements are in millimetres and are coded for ordering purposes
n Height is always indicated first – sizes are finished sizes and do not include building-in fin
n Higher wind and water rating available on products subject to confirmation of structural performance
n Windows and doors with hi lites are subject to confirmation of structural performance
n When ordering, please state left or right hand opening as viewed from the exterior of the building
n Timber reveal lining is available
n Timber reveal lining is not fitted to the door sill
n Building in and prepared opening ties are available for both window and door products
n Black hardware standard
n Mesh vent windows do not comply with AS2047 and the Building Code of Australia
n All doors are fitted with safety glass and motif
Designer Bar Options
Designer Bar Options available for double hung, awning, fixed lite windows, sliding windows, sliding doors, casements, bi-fold doors and french doors.
XO1218 Traditional Colonial
XO1218 Australian Colonial
XO1218 Traditional Federation
XO1218 Australian Federation
XO1218 Highlander
Hinged
WINDOWS AND DOORS
Design Styles
WINDOWS AND DOORS
Product Care Guide
Maintenance of Powder Coated Aluminium Finishesn In a rural atmosphere, cleaning may not be needed more
frequently than every 6 months.
n In industrial and marine environments, more frequent cleaning (e.g. monthly, every 3 months is necessary).
n It is important that non-abrasive mild detergent solution is used for cleaning.
n Add the non-abrasive mild detergent solution to a bucket of warm water.
n Wet a clean soft rag then wipe the aluminium.
n Make sure that the surfaces are thoroughly rinsed after cleaning to remove all residues.
Maintenance of Window and Door Glassn All glass surfaces should be kept clean by prompt removal
of all dirt.
n Use clean water and soft clean rag as buttons or grit can scratch the glass.
n In some instances, a small amount of mild detergent may be of some benefit. However, DO NOT use any form of abrasive cleaner or household cleaners.
n When using detergent make sure that the surfaces are rinsed well after cleaning to remove any detergent residue.
Special instructions for Solar Comfort glass, and other Low-E coated glass products
n The special coating on these types of glass is generally more difficult to clean.
n Use only soft, clean cloth, free from grit or buttons with a mild soap or detergent and water or recommended glass cleaner solution.
n Make sure to dry off excess water.
n DO NOT use abrasive cleaning agents.
Refer to our Solar Comfort Cleaning Recommendations document for more information.
Maintenance of Hardwaren General periodic maintenance is required on all hardware
supplied such as locks, hinges, catches, closers and the like.
n The external finish of hardware must be kept clean by removing any harmful residue (especially salt spray) from the surface using a non-abrasive cleaning agent.
n Internal mechanisms of locks, catches, etc should be kept in good working order by applying a light spray of lubricant (WD40, RP7 or similar).
n Care should be taken during maintenance of internal mechanisms that any finished surface (eg. paint etc) is well protected to avoid damage.
Maintenance of Window and Door Rollersn Remove the sliding panel of the product from the inside
of the house. With the window or door partly open, lift the sliding panel up into the head while tilting the bottom of the panel towards you, out over the sill. Slide the panel downwards to remove it from the frame.
n Use a vacuum cleaner with a narrow nozzle to clean the track thoroughly.
n Use a soft rag and water mixed with mild detergent to wipe the track and rollers.
n It is important that rollers are cleaned 3-4 times a year.
Maintenance of Insect and Safety Screensn Clean screens 3-4 times a year.
n Add a small amount of mild detergent to a bucket of warm water.
n Remove the screen from the window.
n Hose the screen down thoroughly. Dip a soft nylon brush into the bucket of water and gently brush the screen.
n Hose down well.
n Allow the screen to dry before replacing in the window.
Maintenance of Stainless View™ and Ali-View™ Screensn Stainless View™ and Ali-View™ screens should be cleaned
at frequent intervals as indicated in the table below.
n It is important that non-abrasive mild detergent solution combined with warm water and a clean, soft, non-abrasive cloth, are used for cleaning.
n Hand cleaning is recommended except for multi-storey buildings and large commercial projects where carefully controlled methods to loosen deposits of dirt and grime are required.
n It is essential to finish off the cleaning by thoroughly rinsing all surfaces to remove all residue.
n Fibre brushes may be used to loosen dirt and grime, but abrasive papers such as sand paper or emery paper MUST NOT be used.
Recommended Maintenance Intervals
Type of Environment Definition of Environment
Maximum Maintenance
Intervals
Mild Being rural, away from the coast and remote industry and urban activity
6 Months
Moderate Being mainly urban, inland and away from heavy industrial activity
3 Months
Tropical / Severe
Being coastal/marine, subject to salt deposition and within 15km of the eastern coast or 10km of the western coast of Australia
2-4 Weeks
On Site Protection Guidelines
Bradnam’s recommend that builders follow the instructions below to minimise the risks of damage to windows and doors on site.
n Windows and doors should be handled carefully. Ensure that they are carried in the vertical position with sashes locked.
n If possible store windows and doors under cover to protect against damage. During storage, make sure that they are upright on their sills against a flat, structurally secure, vertical surface such as a shed and that they are off the ground on timber blocks.
n Under no circumstances should windows and doors be placed against a tree or post as they can be subject to permanent damage.
n To prevent strong wind from damaging windows and doors, ensure they are tied firmly in position – but take care that ropes do not rub against the aluminium.
n Windows and doors should never come into contact with acids, mortar, magnesite, wet plaster, paint, welding splatter and the like.
n If contact does occur the contamination must be removed as soon as possible to minimise damage to the glass or aluminium.
n Contamination should be removed using a soft rag, non-abrasive mild detergent and warm water to avoid staining or scratching windows and doors.
It is the responsibility of the builder or owner to ensure that once windows and doors are delivered, that they are adequately protected from site work damage.
STANDARD SIZES
Sliding Windows
Note: Sliding Windows may be subject to local variation or regulatory requirements
X = Sliding Panel O = Fixed Panel (Viewed from exterior)
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
n Also available in OX or OXXO configurations
n OXXO configuration is available in sizes 1810mm in width and larger
O X O X X O
STANDARD SIZES
Double Hung Windows
Note: Double Hung Windows may be subject to local variation or regulatory requirements
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
STANDARD SIZES
Note: Awning Windows may be subject to local variation or regulatory requirements
Awning Windows
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
Note: All Awning Window sashes come standard with a chain winder
STANDARD SIZES
Note: Essential Casement Windows may be subject to local variation or regulatory requirements
Essential Casement Windows
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
Note: Maximum sash width 610mm
STANDARD SIZES
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
Signature Casement Windows
Note: Signature Casement Windows may be subject to local variation or regulatory requirements
STANDARD SIZES
Bi-fold Windows
STUDOPENING
FRAME SIZE1690mm1570mm1330mm
FRAME SIZE
FRAME SIZE3370mm3110mm2690mm
FRAME SIZE5050mm4790mm4310mm
STUD OPENING1750mm1630mm1390mm
STUD OPENING3430mm3170mm2750mm
STUD OPENING6010mm4850mm4370mm
660mm920mm
1090mm1260mm1430mm1520mm
600mm860mm1030mm1200mm1370mm1460mm
Note: Bi-fold Windows may be subject to local variation or regulatory requirements
Bi-Fold Numberingeg: 321 (View from left to right)
3 2 1
Total panels No of panels No of panels opening to left opening to right
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
STANDARD SIZES
Bay Windows
Note: Bay Windows may be subject to local variation or regulatory requirements
135º Bay Window / Window SetoutWidth of window A = Slab dimension A – 140mm
Width of window B = Slab dimension B – 160mm
Width of window C = Slab dimension C – 160mm
Stud opening D = (2 x Slab dimension B x 0.7071) + Slab dimension A – 130mm where B and C are equal
90º Bay Window SetoutWidth of window A = Slab dimension A – 300mm
Width of window B = Slab dimension B – 150mm
Width of window C = Slab dimension C – 150mm
Slab Setout Dimension160
Bottom Plate
Face of BrickworkFlush with edge of slab
Slab Dimension A
A
135º
Slab Dimension CSlab D
imen
sion B
D Stud Opening
B C
Slab Dimension A
A135º
Slab Dimension C
Slab D
imen
sion B
D Stud Opening
B
C
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
2148mm 2688mm 3228mm 3588mm
2208mm 2748mm 3288mm 3648mm
DOOR SIZE
OPENING
STUD
2130mm 2100mm
XXO2122 XXO2127 XXO2132 XXO2136
4038mm
4098mm
XXO2140
DOOR SIZE
OPENING
STUD
2130mm 2100mm
4266mm
OXXXXO2143
5346mm
4326mm 5406mm
OXXXXO2153
6246mm
6306mm
OXXXXO2162
2148mm 2688mm 3228mm 3588mm
2208mm 2748mm 3288mm 3648mm
DOOR SIZE
OPENING
STUD
2430mm 2400mm
XXO2422 XXO2427 XXO2432 XXO2436
4038mm
4098mm
XXO2440
DOOR SIZE
OPENING
STUD
2430mm 2400mm
4266mm
OXXXXO2443
5346mm
4326mm 5406mm
OXXXXO2453
6246mm
6306mm
OXXXXO2462
FRAME SIZE
OPENING
STUD
1450mm
1510mm
1810mm
1870mm
2170mm
2230mm
2410mm
2470mm
XO2115 XO2118 XO2122 XO2124
2710mm
2770mm
XO2127
XO2427XO2415 XO2418 XO2421 XO2424
2130mm 2100mm
2430mm 2400mm
OXXO2129 OXXO2136 OXXO2143 OXXO2148
OXXO2429 OXXO2436 OXXO2443 OXXO2448
FRAME SIZE
OPENING
STUD
2864mm
2924mm
3584mm
3644mm
4304mm
4364mm
4784mm
4844mm
2130mm 2100mm
2430mm 2400mm
OXXO2154
OXXO2454
5384mm
5444mm
OXO2122 OXO2127 OXO2132 OXO2136
FRAME SIZE
OPENING
STUD
2148mm
2208mm
2688mm
2748mm
3228mm
3288mm
3588mm
3648mm
2130mm 2100mm
OXO2422 OXO2427 OXO2432 OXO2436
2430mm 2400mm
OXO2140
4038mm
4098mm
OXO2440
Also available in OX configuration
Note: Sliding Doors may be subject to local variation or regulatory requirements
X = Sliding Panel O = Fixed Panel (Viewed from exterior)
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
Sliding Doors
STANDARD SIZES
Also available in OXX configuration
2148mm 2688mm 3228mm 3588mm
2208mm 2748mm 3288mm 3648mm
DOOR SIZE
OPENING
STUD
2130mm 2100mm
XXO2122 XXO2127 XXO2132 XXO2136
4038mm
4098mm
XXO2140
DOOR SIZE
OPENING
STUD
2130mm 2100mm
4266mm
OXXXXO2143
5346mm
4326mm 5406mm
OXXXXO2153
6246mm
6306mm
OXXXXO2162
2148mm 2688mm 3228mm 3588mm
2208mm 2748mm 3288mm 3648mm
DOOR SIZE
OPENING
STUD
2430mm 2400mm
XXO2422 XXO2427 XXO2432 XXO2436
4038mm
4098mm
XXO2440
DOOR SIZE
OPENING
STUD
2430mm 2400mm
4266mm
OXXXXO2443
5346mm
4326mm 5406mm
OXXXXO2453
6246mm
6306mm
OXXXXO2462
FRAME SIZE
OPENING
STUD
1450mm
1510mm
1810mm
1870mm
2170mm
2230mm
2410mm
2470mm
XO2115 XO2118 XO2122 XO2124
2710mm
2770mm
XO2127
XO2427XO2415 XO2418 XO2421 XO2424
2130mm 2100mm
2430mm 2400mm
OXXO2129 OXXO2136 OXXO2143 OXXO2148
OXXO2429 OXXO2436 OXXO2443 OXXO2448
FRAME SIZE
OPENING
STUD
2864mm
2924mm
3584mm
3644mm
4304mm
4364mm
4784mm
4844mm
2130mm 2100mm
2430mm 2400mm
OXXO2154
OXXO2454
5384mm
5444mm
OXO2122 OXO2127 OXO2132 OXO2136
FRAME SIZE
OPENING
STUD
2148mm
2208mm
2688mm
2748mm
3228mm
3288mm
3588mm
3648mm
2130mm 2100mm
OXO2422 OXO2427 OXO2432 OXO2436
2430mm 2400mm
OXO2140
4038mm
4098mm
OXO2440
Also available in
STANDARD SIZES
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
Sliding Doors
Non Standard Configurations Availablen Availability subject to local variations or climate requirements.
n Screening not available in these non standard configurations.
X = Sliding Panel O = Fixed Panel (Viewed from exterior)
Note: Sliding Doors may be subject to local variation or regulatory requirements
2148mm 2688mm 3228mm 3588mm
2208mm 2748mm 3288mm 3648mm
DOOR SIZE
OPENING
STUD
2130mm 2100mm
XXO2122 XXO2127 XXO2132 XXO2136
4038mm
4098mm
XXO2140
DOOR SIZE
OPENING
STUD
2130mm 2100mm
4266mm
OXXXXO2143
5346mm
4326mm 5406mm
OXXXXO2153
6246mm
6306mm
OXXXXO2162
2148mm 2688mm 3228mm 3588mm
2208mm 2748mm 3288mm 3648mm
DOOR SIZE
OPENING
STUD
2430mm 2400mm
XXO2422 XXO2427 XXO2432 XXO2436
4038mm
4098mm
XXO2440
DOOR SIZE
OPENING
STUD
2430mm 2400mm
4266mm
OXXXXO2443
5346mm
4326mm 5406mm
OXXXXO2453
6246mm
6306mm
OXXXXO2462
Note: Highlighted sizes are site glazed and assembled
FRAME SIZE
OPENING
STUD
1450mm
1510mm
1810mm
1870mm
2170mm
2230mm
2410mm
2470mm
XO2115 XO2118 XO2122 XO2124
2710mm
2770mm
XO2127
XO2427XO2415 XO2418 XO2421 XO2424
2130mm 2100mm
2430mm 2400mm
OXXO2129 OXXO2136 OXXO2143 OXXO2148
OXXO2429 OXXO2436 OXXO2443 OXXO2448
FRAME SIZE
OPENING
STUD
2864mm
2924mm
3584mm
3644mm
4304mm
4364mm
4784mm
4844mm
2130mm 2100mm
2430mm 2400mm
OXXO2154
OXXO2454
5384mm
5444mm
OXO2122 OXO2127 OXO2132 OXO2136
FRAME SIZE
OPENING
STUD
2148mm
2208mm
2688mm
2748mm
3228mm
3288mm
3588mm
3648mm
2130mm 2100mm
OXO2422 OXO2427 OXO2432 OXO2436
2430mm 2400mm
OXO2140
4038mm
4098mm
OXO2440
STANDARD SIZES
Bi-fold Doors
STUDOPENING
FRAME SIZE1690mm1570mm1330mm
FRAME SIZE
FRAME SIZE3370mm3110mm2690mm
FRAME SIZE4210mm3590mm3110mm
STUD OPENING1750mm1630mm1390mm
STUD OPENING3430mm3170mm2750mm
FRAME SIZE2530mm2330mm1810mm
STUD OPENING2590mm2390mm1870mm
STUD OPENING4270mm3650mm3170mm
Note: Bi-fold Doors may be subject to local variation or regulatory requirements
Bi-Fold Numberingeg: 321 (View from left to right)
3 2 1
Total panels No of panels No of panels opening to left opening to right
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
Note: Highlighted sizes are site glazed and assembled
Hinged Doors
The availability of certain sizes and configurations is dependent on the design wind load requirement as per AS2047-2014. Check with your Bradnam’s representative to confirm availability.
Note: Hinged Doors may be subject to local variation or regulatory requirements
STANDARD SIZES
1810mm MAX
2400
mm
MA
X
2100
mm
MIN
2400
mm
MA
X
2100
mm
MIN
970mm MIN
1810mm MAX
970mm MIN
1200mm MAX
300mm MIN
FIXED
925mm MAX
2400
mm
MA
X
2100
mm
MIN
1810mm MAX
970mm MIN
1200mm MAX
300mm MIN
1200mm MAX
300mm MIN
FIXED FIXED
2400
mm
MA
X
2100
mm
MIN
Hinged Door Informationn Standard door leaf widths are 620, 720, 820
n Maximum leaf size is 870mm
n All doors to be supplied with sills
n Operating sashes are available as Side Lites if required
n Hi lites are available subject to confirmation of structural performance
Bradnam’s Windows and Doors Pty Ltd is a member of the Australian Window Association and as such conforms to an Industry Code of Conduct designed to protect consumers.
Subject to the conditions and limitations below Bradnam’s Windows and Doors Pty Ltd guarantees its products against defects arising from faulty workmanship or materials for six years from the date of delivery or installation.
For the purpose of this warranty “the product” can mean a window, door, insect screen, safety screen, Stainless View™ screen, shower screen, mirror or wardrobe door product ordinarily manufactured and sold by Bradnam’s Windows and Doors Pty Ltd.
Conditions and Limitations
1 The product is installed in accordance with the relevant Australian Standards and building practice. Unless otherwise specifically confirmed in writing, Bradnam’s Windows and Doors Pty Ltd accepts no responsibility for waterproofing and/or re-sealing of penetrations and such remains the responsibility of others.
2 The product has been maintained according to Bradnam’s Windows and Doors Pty Ltd maintenance recommendations and has not been subject to misuse, physical abuse, or neglect.
3 In respect of window and door products, this guarantee is void if Bradnam’s Windows and Doors Pty Ltd insect screens, safety screens or Stainless View screens have not been manufactured and fitted by Bradnam’s Windows and Doors Pty Ltd installers or personnel nominated by Bradnam’s Windows and Doors Pty Ltd;
4 Manufacturing standards and tolerances are not deemed defects, nor are industry variations in the colour of aluminium componentry.
5 Bradnam’s Windows and Doors Pty Ltd accepts no responsibility for glass breakage (except for faulty workmanship or materials). Wire reinforced glass, toughened glass, float glass, laminated glass, mirror glass and framed mirror glass is guaranteed against defects and degradation for one (1) year.
6 Moving parts, where applicable, which wear out as part of normal use are guaranteed for one (1) year.
7 This guarantee is limited to the repair or replacement of the faulty product at the company’s discretion but does not extend to the installation or refurnishing of a replacement product or any other consequential or indirect damage incurred as a result of the defect. Only repairs carried out by Bradnam’s Windows and Doors Pty Ltd personnel or authorised Bradnam’s Windows and Doors Pty Ltd agents are covered by this guarantee.
8 This guarantee is in addition to all other rights and remedies in respect of this product to which you are entitled under the Competition and Consumer Act 2010 (Cth).
Warranty Claims
Claims under this guarantee must be made within one month of the defect arising in the product. Other than as provided by law Bradnam’s Windows and Doors Pty Ltd will repair or replace the product to the extent that it is functionally equivalent to the original product supplied.
Copies of documentation showing the purchase date of the product should be included with your written claim and forwarded to the nearest Bradnam’s Windows and Doors Pty Ltd office. All warranty claims will initially require a deposit to be paid. After inspection by Bradnam’s Windows and Doors Pty Ltd personnel or authorised agents, the customer will be advise if the claim is covered under the warranty. If the claim is under warranty the deposit will be refunded and the product will be repaired or replace by Bradnam’s Windows and Doors Pty Ltd. Otherwise, upon the customer’s request, Bradnam’s Windows and Doors Pty Ltd will provide a quote to rectify the problem.
Victoria Branch Locations
Dandenong
9 Quality Drive Dandenong South VIC 3175 Phone (03) 8795 9666 Fax (03) 8795 9688 Email [email protected]
Point Cook
Unit 7, 22-30 Wallace Avenue Point Cook VIC 3030 Phone (03) 9371 9777 Fax (03) 9931 1723 Email [email protected]
Showrooms also available in Queensland and New South Wales
Bradnam’s 6 Year Guarantee Terms & Conditions
Bradnam’s Windows and Doors, QBCC Act lic 58885 | © Bradnam’s Windows and Doors Jun 2016
For more information call Bradnam’s on
1300 WINDOWS 1300 946369or visit bradnams.com.au