Upload
bishoy-nabil
View
221
Download
0
Embed Size (px)
Citation preview
8/18/2019 very important case
1/16
LCD Colour TV
OWNER'SMANUAL
Owner's Record
You will find the model number and serial number on
the back of the TV. Record these numbers in the spaces
provided below. Refer to them whenever you call upon
your TOSHIBA dealer regarding this product.
Model number:
Serial number:
19HV10 Series
24HV10 Series
32HV10 Series©2011 TOSHIBA CORPORATION
All Rights Reserved VX1A00213500TD/J
8/18/2019 very important case
2/16
– 2 –
Welcome to Toshiba
• Thank you for purchasing this Toshiba LCDColour TV. This manual will help you use theexciting features of your new TV.
• Instructions in this manual are based on usingthe remote control.
• You also can use the controls on the TV if theyhave the same name as those referred to onthe remote control.
• Please read all safety and operatinginstructions in this manual carefully, and keepthis manual for future reference.
Important Safety Instructions
Be sure to observe the following instructions andprecautions to ensure safe use of this TV.
Installation
1) WARNING: To prevent injury, this apparatusmust be securely attached to the floor/wall inaccordance with the installation instructions. Install the TV in a horizontal, stablelocation. Attach the TV to the stand withthe mounting screw (only supplied on32HV10 models).• If the TV is not installed securely, it may lean
or fall over and cause an injury.• To prevent injury, use the exclusive optional
stand or wall-hanging bracket to install
this TV on the oor or wall securely in accordance with a qualied technician.
Top view
Screw hole
2) Never place the TV in an unstabilizedlocation such as on a shaky table, inclineor location subject to vibration.• Only use cabinets or stands recommended
by the TV manufacturer.• Only use furniture that can safely support
the TV.• Ensure that the TV is not hanging over the
edge of the supporting furniture.• Never place the TV on tall furniture (for
example, cupboards or bookcases) withoutanchoring both the furniture and the TV to asuitable support.
• Never stand the TV on cloth or othermaterial placed between the TV andsupporting furniture.
The TV may drop or fall off, which may causean injury or damage.
Contents
Connecting an aerial ..............................5
Exploring your new TV ...........................5
TV panel and remote controls ................6
TV back panel connections ....................7
Connecting HDMI devices ......................7
Turning the TV on ................................... 8
Learning about the menu system ...........8
SETUP menu ....................................... 10
Programming channels into
the TV’s channel memory .....................10
Selecting the video input
source to view ......................................11
Picture adjustment ...............................12
Sound menu ......................................... 13FUNCTION menu .................................13
Changing the position ..........................13
Switching between two positions .........14
Displaying the on-screen information ...14
Selecting stereo/bilingual .....................14
Setting the Sleep Timer menu ..............14
Troubleshooting ....................................15
Broadcast system .................................15
Specications .......................................16
Pedestal stand Assembling
1 Remove two screws (A) on the TV.(Use two screws to attach the pedestal stand.)
A
2 After the TV is installed on the pedestal stand,use two screws (A) to attach the pedestal stand.
A
8/18/2019 very important case
3/16
– 3 –
3) Never stand or climb on the TV.• Educate children about the dangers of
climbing on furniture to reach the TV or itscontrols.
Be especially careful in households with
children to prevent them through climbing on
top of the TV. It may move, fall over, break,
become damaged or cause an injury.
4) Always connect the power plug to anappropriate electrical outlet equipped with110-240 V, AC 50/60 Hz.
Never use the TV outside the specied voltage
range. It may cause a re or an electric shock.
About the fuse (only for E models)
In a three pin earthing-type, the fuse tted
in this plug is approved by ASTA or BSI to
BS1362. It should only be replaced by a
correctly rated and approved type and thefuse cover must be retted.About the use• Make sure to insert the plugs rmly, when
plugging the AC power cord into the TV setend and wall outlet end.
• Make sure to hold the plug, whenunplugging the AC power cord.
• Never use other cord except for suppliedAC power cord, and never use the suppliedpower cord for any other purpose.
5) Never insert or remove the power plug withwet hands.
This may cause an electric shock.
6) Never block or cover the slots andopenings in the cabinet.• Never place the TV so that it is facing
upward or on its side.• Never place the TV in a closet, bookcase or
other similar area where the ventilation ispoor.
• Never drape a newspaper, tablecloth or
curtain on the TV.• When installing the TV against a wall,
always keep the TV at least 10 cm awayfrom the wall.
• Never place the TV on a soft unstablesurface, such as a carpet, or a cushion.
The inside of this TV will overheat if the
ventilation holes are covered, blocked or
sealed, which may result in a re.
7) Never place the TV near a heater or indirect sunlight.
The surface of the cabinet or power cord maymelt and result in a re or an electric shock.
8) Never place the TV in an area exposedto high humidity levels, such as in abathroom or close to a humidifier.
This may cause a re or an electric shock.
9) Never place the TV next to a stove where itwill be exposed to oil, smoke, or steam, or
in a location where there is a large quantityof dust.
This may cause a re or an electric shock.
10) Precautions for moving the TV• When moving the TV, be sure to remove the
plug from the wall outlet and disconnect theaerial cable and audio/video cables, anysteady ties and mounting screw. A re or anelectric shock may result if the power cord isdamaged.
• When carrying the TV, at least two people
are needed. Be sure to carry it upright.• Never carry the TV with the screen facing upor down.
11) Precautions for installing on outdoor aerial
An outside aerial system should not be
located in the vicinity of overhead power lines,
or other electric light or power circuits.
If the aerial falls down or drops, it may cause
an injury or an electric shock.
Use
1) Never place hot objects or open flamesources, such as lighted candles ornightlights, on or close to the TV.
High temperatures can melt plastic and lead to res.
2) The apparatus shall not be exposed todripping or splashing and that no objectsfilled with liquids, such as vases, shall beplaced on the apparatus.
When liquids are spilled or small items are
dropped inside the TV, this may cause a re or
an electric shock.If small objects drop inside the TV, turn off the
TV and remove the power plug from the outlet
immediately and contact a service technician.
3) Never insert objects (metal or paper)or pour water inside the TV throughventilation holes and other openings.
These items may cause a re or an electric
shock. If these objects are inserted inside the
TV, turn off the TV and remove the power plug
from the outlet immediately and contact a
service technician. Be especially careful that
children do not insert objects in the TV.
8/18/2019 very important case
4/16
– 4 –
4) When the TV will not be used for a longperiod of time, such as during vacation ortravel, remove the power plug from the walloutlet for safety.• The TV is not completely disconnected from
the power supply line, as minute current isconsumed even when the 1 Power switch is
turned off.• The Mains plug or an appliance coupler isused as the disconnect device, thereforethe disconnect device shall remain readilyoperable.
5) Never pull on the power cord whenremoving the plug from the wall outlet.
Always hold the plug rmly when removing
it. If the power cord is yanked, the cord may
become damaged and a re or an electric
shock may occur.
6) Never cut, break, modify, twist, bunch up orbent the cord or apply excessive force ortension to it.
Never place heavy objects on the cord or allow
it to overheat as this may cause damage, a
re or an electric shock. Contact a service
technician if the power cord is damaged.
7) If there is thunder or lightning, never touchthe aerial cable or other connected cables.
You may suffer an electric shock.
Service
1) Never repair, modify or disassemble the TVby yourself.
It may cause a re or an electric shock.
Consult a service technician for inspection and repairs.
2) When a malfunction occurs, or if smoke oran unusual odor comes from the TV, turnoff the TV and remove the power plug fromthe outlet immediately.
Make sure that the smoke or smell hasstopped, then contact a service technician.
If the TV is still used in this condition, it may
cause a re or an electric shock.
3) If the TV is dropped or the cabinet isbroken, turn off the TV and remove thepower plug from the outlet immediately.
If the TV has power in this condition, it may
cause a re or an electric shock. If the cabinet
is broken, be careful when handling the TV to
prevent an injury.
Contact a service technician for inspection and repair.
4) When the TV reaches the end of its usefullife, ask a qualified service technician toproperly dispose of the TV.
Note:
The lamp unit contains a small amount of
mercury. Disposal of mercury may be regulated
due to environmental considerations.
Dispose of the used lamp unit by the approvedmethod for your area. For disposal or recyclinginformation, please contact your local authorities.
Cleaning
1) Remove the power plug before cleaning.
Never use solvents such as benzine or thinner
to clean the TV.• These solvents may distort the cabinet or
damage its nish.• If rubber or vinyl products remain in contact
with the TV for a long time, a stain may result.If the cabinet becomes dirty, clean it with a
soft, dry cloth.
When cleaning the surface of the LCD display,
wipe the panel surface gently with a soft, dry
cloth.
2) Periodically disconnect the power plugfrom the outlet and check it.If dust has collected on the power plugconnectors, clean off the dust with a drycloth.
This dust may cause a re due to reduced
insulation on the plug.
Important information
1) About LCD screen• If you have the LCD screen facing to the
sun, the LCD screen will be damaged. Beaware of locating the TV close to a windowor outdoors.
• Never press the LCD screen strongly orscratch it, and never put anything on it.
These actions will damage the LCD screen.
2) About cabinet and LCD screen
Never spray volatile compounds such as
insecticide on the cabinet and LCD screen.
This may cause a discolouration or damage
the cabinet and LCD screen.
3) Some pixels of the screen do not light up
The LCD display panel is manufactured
using an extremely high level of precision
technology, however sometimes some pixelsof the screen may be missing picture elements
or have luminous spots. This is not sign of
malfunction.
8/18/2019 very important case
5/16
– 5 –
4) About Interference
The LCD display may cause interference
in image, sound, etc. of other electronic
equipment that receives electromagnetic
waves (e.g. AM radios and video equipment).
5) About using under the low temperature
placesIf you use the TV in the room of 0°C or less,
the picture brightness may vary until the
LCD monitor warms up. This is not a sign of
malfunction.
6) About afterimage
If a still picture is displayed, an afterimage
may remain on the screen, however it will
disappear. This is not a sign of malfunction.
Exemptions• Toshiba is not liable for any damage caused
by res, natural disaster (such as thunder,earthquake, etc.), acts by third parties,accidents, owner’s misuse, or uses in otherimproper conditions.
• Toshiba is not liable for incidental damages(such as prot loss or interruption in business,modication or erasure of record data, etc.)caused by use or inability to use of product.
• Toshiba is not liable for any damage causedby neglect of the instructions described in theowner’s manual.
• Toshiba is not liable for any damage caused bymisuse or malfunction through simultaneoususe of this product and the connectedequipment.
Trademark Information• HDMI, the HDMI logo, and High-Denition
Multimedia Interface are trademarks orregistered trademarks of HDMI Licensing LLCin the United States and other countries.
Connecting an aerial
Optimum reception of colour requires a goodsignal and will generally mean that an outdooraerial must be used.The exact type and positioning of the aerial willdepend upon your particular area.
Your Toshiba dealer or service personnel canbest advise you on which aerial to use in yourarea.Before connecting the aerial cable, turn off allmain power switches.
IN
OUT
VHF and/or
UHF aerial
300 7 twin-lead feeder
75 7aerialterminal
Aerial adaptor
(not supplied)
(75 7 coaxial) (not supplied)
Aerial cable
75 7 aerial
terminal
75 7 coaxial cable
Plug
(not supplied)
Media Recorder TV back view
Exploring your new TV
Installing the remote control batteriesRemove the battery cover.Insert two R03 (AAA) batteries matching the –/+polarities of the battery to the –/+ marks insidethe battery compartment.
Cautions: • Dispose of batteries in a designated disposal
area. Batteries must not be exposed toexcessive heat such as sunshine, fire or thelike.
• Attention should be drawn to the environmentalaspects of battery disposal.
• Never mix battery types or combine usedbatteries with new ones.
8/18/2019 very important case
6/16
– 6 –
Notes: • If the remote control does not operate correctly,
or if the operating range becomes reduced,replace both batteries with new ones.
• If the batteries are dead or if you will not usethe remote control for a long time, remove thebatteries to prevent battery acid from leakinginto the battery compartment.
Effective range
within 5 m
TV panel and remote controls
• You can operate your TV using the buttons onthe side panel or the remote control. The backof the panel provide the terminal connections toconnect other equipment to your TV.
• For the use of each control, see the pages inbrackets.
TV front view
Left side view
GREEN / RED
1
2
3
4
2
5
8
0
BACK
SLEEP
1
4
7
MENU
3
6
9
EXIT
OK
CT-90384
10
12
14
15
3
8
6
9
11
13
16
4
7
2
5
1 Power LED — Power indicator.
2 Power on/standby — Press to turn the TVon/standby.
3 Programme position — When no menuis on screen, these buttons select theprogramme position.MENU up/down — When a menu is on-screen, these buttons function as up/down
menu navigation buttons.4 Volume — When no menu is on-screen,
these buttons adjust the volume level. MENU left/right — When a menu is on-screen, these buttons function as left/rightmenu navigation buttons or adjust settings.
5 To set the sleep time
6 Input source selection
7 Number buttons (0-9)
8 To display on-screen information
9 To return to the previous programme10 Stereo/Bilingual selection
11 Picture Size
12 This button turns the sound off/on
13 On-screen Menus
14 To exit menu
15 To return to the previous menu
16 To conrm your selection
8/18/2019 very important case
7/16
– 7 –
TV back panel connections
AC IN
L/ MONO
L/ MONO
AUDIO
AUDIO
VIDEO VIDEO
(1 )
(2)
AUDIO
R
R
Y
HDMI
PR
CR
/
PB
CR /
SERVICEUSE ONLY
COMPONENT/ VIDEO INPUT
VCR (Normal)
DVD video player
(with component video outputs)
Set Top Box
or
TV back view
HDMI device
V ID EO A UD IOL R
IN
OUT
HDMIOUT
Power cord*
Power cord ** Make sure to insert the plugs firmly, when
plugging the AC power cord into the TV set endand wall outlet end.
* Make sure to hold the plug, when unpluggingthe AC power cord.* Never use other cord except for supplied AC
power cord, and never use the supplied powercord for any other purpose.
* The exact power cord will vary according to thecountry.
About connecting an HDMI device• Use for one HDMI cable (type A connector)• For proper operation, it is recommended that
you use a short HDMI cable.• HDMI cable transfers both video and audio.
Connection example
• o HDMI (input terminal) — High-DenitionMultimedia Interface input receives digitalaudio and uncompressed digital video froman HDMI device. Use for one HDMI cable(type A connector) For proper operation, it isrecommended that you use a short HDMI cable.HDMI cable transfers both video and audio.
• A (aerial input terminal) — Analogue aerialsignal input.
• o (2) COMPONENT / VIDEO INPUT (inputterminals) — High-denition component videoand standard (analogue) stereo audio inputs,or standard (composite) video and standardstereo audio inputs.
• o (1) VIDEO (input terminal) — Standardvideo and standard stereo audio input.
Notes: • Before connecting any external equipment, turn
off all main power switches.• The unauthorized recording of TV programmes,DVDs, video tapes and other materials mayinfringe upon the provisions of copyright law.
• The COMPONENT VIDEO INPUT consists ofthree component video signals ( Y , P B /C B , P R / C R ) and provides the best picture performance.These terminals can only be used with thecomponent video compatible equipment e.g.DVD video player, etc.
• Additional equipment and cables shown are notsupplied with this TV.
• o (2) COMPONENT / VIDEO INPUT terminals
Red
White
Yellow
Red(Audio)
White
Green
Blue
RedL/
MONO
AUDIO
VIDEO
(2)
AUDIO
R
Y
PRCR
/
PBCR
/
COMPONENT/ VIDEO INPUT
L/ MONO
AUDIO
VIDEO
(2)
AUDIO
R
Y
PRCR
/
PBCR
/
COMPONENT/ VIDEO INPUT
Standard video mode Component video mode
Connecting HDMI devices
• When turning on your electronic components,turn on the TV rst, and then the HDMI device.
• When turning off your electronic components,turn off the HDMI device rst, and then the TV.
• This TV may not be compatible with featuresand/or specications that may be added in thefuture.
• This TV is only operable with L-PCM on
32/44.1/48 kHz and 16/20/24 bits.• This TV is able to connect with HDMI devices.
But it is possible that some HDMI devices maynot operate properly with this TV.
8/18/2019 very important case
8/16
– 8 –
Turning the TV on
Switching on the TV
Connect the power cord to a wall outlet, the1 power indicator lights in red (standby mode).
1 Press on the remote control or on the TVleft side panel, the 1 power indicator lights ingreen.
Note: If you watch black and white programmes whenthe Colour System mode is set to Auto , colournoise may appear on the screen. In this caseselect the appropriate Colour System (For thesystem of each country or region, refer to pages10, 15).
Switching off the TV
1 Press on the remote control or on the TVleft side panel to switch to the standby mode.
Notes: • When the TV will not be used for a long period
of time, such as during vacation or travel,remove the power plug from the wall outlet.
• The TV will automatically turn itself off afterapproximately 15 minutes if it is tuned to avacant channel or a station that completes itsbroadcast for the day. This function does notwork in external input or Blue screen Off mode.
• If power is cut off while you are viewing the TV,the Last Mode Memory function turns on theTV automatically when power is applied again.If power is going to be off for a long time andyou are going to be away from your TV, unplugthe power cord to prevent the TV from turningon in your absence.
Learning about the menu system
We suggest you familiarize yourself with thedisplay charts before using the menu system:
• Press MENU to display menu, then press v orw to select main menu headings.
• Press s or r to select an item.• Press v or w to select or adjust setting.• Press OK to display the next menu.
Connecting an HDMI deviceThe HDMI input on your TV receives digital audioand uncompressed digital video from an HDMIdevice.This input is designed to accept HDCPprogramme material in digital from CEA-861-Dcompliant consumer electronic devices (such asa set top box and DVD player with HDMI output).The HDMI input is designed for best performancewith 1080i (50/60 Hz) and 1080p (50/60 Hz)high-denition video signals, but will also acceptand display 480i, 480p, 576i, 576p, and 720p(50/60 Hz) and VGA (VESA 640 × 480 @ 60 Hz)signals.• HDMI: High-Denition Multimedia Interface• HDCP: High-bandwidth Digital Content
Protection• CEA-861-D compliance covers the
transmission of uncompressed digital videowith high-bandwidth digital content protection,which is being standardized for reception ofhigh-denition video signals. Because this isan evolving technology, it is possible that somedevices may not operate properly with the TV.
• Acceptable PC signal format: S-VGA: VESA 800 5 600 @ 60 Hz XGA: VESA 1024 5 768 @ 60 Hz W-XGA: VESA 1280 5 768 @ 60 Hz W-XGA: VESA 1360 5 768 @ 60 Hz S-XGA: VESA 1280 5 1024 @ 60 HzHowever, these signal formats are converted tomatch the number of pixels of the LCD panel.
Therefore, the TV may not display small textproperly.If you connect this unit to your PC, thecompressed image is displayed in S-XGA mode,therefore the picture quality may deteriorate andcharacters may not be read.• L-PCM: Linear-Pulse Code Modulation• Supported Audio format: L-PCM sample rate
32/44,1/48 kHz
8/18/2019 very important case
9/16
– 9 –
Displaying the menu chart
PICTURE
BacklightContrastBrightnessColourTintSharpnessColor TemperatureNoise Reduction
OK Enter
OK Enter
OK Enter
PICTURE
BacklightContrastBrightnessColourTintSharpnessColor TemperatureNoise Reduction
Backlight
SOUND
SETUP
LanguageAuto TuningManual TuningManual SettingsReset TVSystem Information
OK Enter
Pos. Lab el
Manual Tuning
0
123456789
OK Enter
FUNCTION
Panel Lock
Blue ScreenSide Panel
OK Enter
Edit
MTSDualBassTrebleBalanceAudio Level Offset
100100
50
5000
CoolLow
CoolLow
Auto
0000
English
SVNxxxx
Off
Off1
FUNCTION
Panel Lock
Blue ScreenSide Panel
Off
Off1
SETUP
LanguageAuto TuningManual TuningManual SettingsReset TVSystem Information
English
SVNxxxx
Dual 1
SOUND
Edit
Edit
FUNCTION
Panel Lock
Blue ScreenSide Panel
Off
Off1
Edit
MTSDualBassTrebleBalanceAudio Level Offset
Auto
0000
Dual 1
SOUND
Edit
Sort
MTSDualBassTrebleBalanceAudio Level Offset
Auto
0000
Dual 1
10050
100100
5000
100
PICTURE
Press MENU ( )
MENU Structure
SOUND
SETUP
FUNCTION
PICTURE
SOUND
SETUP
OK
FUNCTION
Backlight
SOUND
Manual Tuning
FUNCTION
MENU
Notes: • In the video input mode (VIDEO, COMPONENT and HDMI), Auto Tuning and Manual Tuning are not
available. Instead, Manual Setting appears in the SETUP menu.• If you connect external equipment via component video source to external input, Colour System
selection in the Manual Setting menu is not available.• If you do not make a selection for a while, the menu display disappears automatically.
• If you want to close the menu display instantly, press EXIT .• To return to the previous menu, press BACK .• System Information in the SETUP menu is for service use only.
8/18/2019 very important case
10/16
– 10 –
• Most of the picture/sound controls andfunctions are available. However features notavailable will be greyed out.
SETUP menu
Selecting the menu language
Choose from 8 different languages (English,Malay, Thai, Vietnamese, Russian, Arabic,Persian or French) for the on-screen display.
1 From the SETUP menu, press s or r toselect Language.
2 Press v or w to select the desired language.
Programming channels into the TV’schannel memory
• First, use the Auto Tuning function to preset allthe active channels in your area automatically.Then, arrange the preset channels with theManual Tuning function so that you can tuneinto only desired channels.
• Use the Manual Tuning operation if desiredchannels cannot be preset with the AutoTuning or if you would like to preset channelsto specic position numbers one by one.
• If a signal with a different Colour System is received after you have set Auto Tuning,switch to the correct Colour System in theManual Tuning menu.
Auto Tuning
1 From the SETUP menu, press s or r toselect Auto Tuning.
2 Press OK to display the Auto Tuning menu.Auto Tuning
Previous settings will be Lost!
Press EXIT for no change.
3 Press OK to start the automatic search.The search will begin for all available stations.
4 When the automatic search is completed,the TV will automatically appear the rstprogramme position.
5 Press PU or P u to view the programmedposition.
Note: When you preset the channel which soundof broadcast transmission system adopts “M”
system, the sound system may not be tunedcorrectly if the radio waves transmit badly. At thattime, preset the channel by Manual Tuning .
The countries such as Myanmar, Chile, Colombiaapply to this case. See page 15 for more details.
Manual Tuning
1 From the SETUP menu, press s or r toselect Manual Tuning.
2 PressOK
to display theManual Tuning
menu.Press s or r to select the programmeposition you want to arrange.
3 Press OK to display the breakdown menu.Press v or w to select an item, then press s or r to select the item as shown below.
Manual TuningSystem
1 B/G A 0
B D FECA
A. System (Sound) (- page 15)
B. Colour System (- page 15)
A : AUTO (Automatic), P : PAL,S : SECAM, 4 : NTSC 4.43 (MHz),3 : NTSC 3.58 (MHz)
C. Position skip selection
Press s or r to turn the position skipoption on “8” or off “(”.
The position will then be skipped when youselect channels with PU or P u.
The “8” mark will appear beside aposition number when you use theNumber button on the remote control.
D. Channel search operation
Press r to search up the band or s tosearch down the band.
Press s or r repeatedly until your desiredchannel is displayed.
When a station is found, it will be displayed. NEVER PRESS ANY OTHER BUTTONS
WHILE THE SET IS TUNING.
E. Manual Fine Tuning Press s or r until better picture and
sound are obtained.
F. Label
Station labels appear under the programmeposition display each time you turn on theTV, select a channel, or press .
To change or create station labels:
1) Press s or r repeatedly to select acharacter for the rst space, then pressv or w.
*(blank space)
8/18/2019 very important case
11/16
– 11 –
2) Repeat step 1) to enter the rest of thecharacters. If you would like a blankspace in the label name, you mustchoose a blank space from the list ofcharacters.
Press OK to store your settings.
Sorting positions• The TV is capable of receiving a number of
different channels depending upon where youlive.
• Sorting programme position is an easy wayof storing each channel on the programmeposition of your choice.
Ex.: To swap channel ABCD (Prog.1) for channelMNOP (Prog.4):
1 From the SETUP menu, presss orr to selectManual Tuning menu, and then press OK.
2 Press s or r to select the channel ABCD,then press w.
10
A B C DE F G HI J K LM N O P
Manual Tuning
Pos. Label
2345678
3 Press s to select the new position “4”, thenpressv.
4 Press r to select the channel MNOP, thenpressw.
5 Press r to select the new position “1”, thenpressv.
6 Conrm new Manual Tuning menu.
Selecting the video input source to view1 Presso on the remote control until the video
input mode list appears on the screen, thenpresss, r oro to select appropriate inputsource.
VIDEO2
TVVIDEO1
Inputs
HDMI
2 Press OK.TV (analogue aerial input),VIDEO1 (o (1), standard video input),VIDEO2 (o (2), standard or componentvideo input)HDMI (HDMI input),
Setting the Manual Setting menu1 From the SETUP menu, press v or w to
select Manual Setting, and then press OK.
2 Pressv orw to select an item, and then presss orr to select the item as shown below.
Manual Setting
Colour System : AUTO
VIDEO1 A
A B
A. Colour System
It may take a while for the colours toappear.
Note: Only standard video signal input, this functionis available.
B. Label
The label allows you to label each inputsource for your TV.
To change or create labels:
1) Press s or r repeatedly to select acharacter for the rst space, then pressv or w.
*(blank space)
2) Repeat step 1) to enter the rest of thecharacters. If you would like a blankspace in the label name, you mustchoose a blank space from the list of
characters.Press OK to store your settings.
Resetting the TVReset TV will reset all TV settings, includingstored channels, to their original factory values.
1 From the SETUP menu, press s or r toselect Reset TV.
2 Press OK to select.A screen will appear warning that all settingswill be lost. Select Yes and press OK tocontinue.
8/18/2019 very important case
12/16
– 12 –
Picture adjustment
Selecting the Picture Size
1 Press until the Picture Size list appearson the screen, then press s or r to selectthe appropriate Picture Size (or press
repeatedly to select the desired Picture Size directly).
Picture Size
Wide4:3Super Live
2 Press OK.
WideUse this setting when watching a wide-screenDVD, widescreen video tape or a 16:9 broadcast(when available). Due to the range of wide-screen formats (16:9, 14:9, 20:9 etc.), you maysee bars on the top and bottom of the screen.
4:3Use this setting to view a true 4:3 broadcast.
Super Live (only analogue aerial and standardvideo input sinal)This setting will enlarge a 4:3 image to t thescreen by stretching the image horizontally,holding better proportions at the centre of theimage. Some distortion may occur.
PC Normal (only HDMI signal input)Use this setting for PC connected via HDMIterminal when receiving PC signal format. Thissetting will display the image correctly withoutdistortion or picture clipping.
PC Wide (only HDMI signal input)Use this setting for PC connected via HDMIterminal when receiving PC signal format. Thissetting will display the image without pictureclipping.
Notes: • Using the special functions to change the size of
the displayed image (e.g. changing the height/ width ratio) for the purpose of public display orcommercial gain may infringe on copyright laws .
• If the aspect ratio of the selected format isdifferent from the one of the TV transmissionor video programme, it can cause a differencein vision. Change to the correct aspect ratio
picture size.
Activating the picture qualityYou can adjust the basic picture quality.
1 From the PICTURE menu, presss orr toselect either Backlight, Contrast, Brightness,Colour, Tint or Sharpness and press OK.
2 Press v or w to adjust the settings.
Selecting the Colour Temperature
You can change the tone of the picture byselecting from three preset colour temperatures:Cool, Natural or Warm.
1 From the PICTURE menu, press s or r toselect Colour Temperature.
2 Press v or w to select mode you prefer. Cool : Lends a blue hue to the picture. Natural : Neutral Warm : Lends a red hue to the picture.
Activating the Noise ReductionIf the receiving signal is weak and the picture isblurry, the picture may be improved when usingthis function.
1 From the PICTURE menu, press s or r toselect Noise Reduction.
2 Press v or w to select Off, Low, Middle orHigh.
Resetting the PICTURE settings
1 From the PICTURE settings menu, press s or r until Reset is selected and press OK.
8/18/2019 very important case
13/16
– 13 –
Sound menu
Setting the MTS (Multi-channel TV Sound)
Auto modeThe MTS Auto mode automatically recognizestereo/bilingual programmes depending on thebroadcast signal.
1 From the SOUND menu, press s or r toselect MTS.
2 Press v or w to select Auto or Mono.
Mono modeIf you experience noise or poor reception of anystereo/bilingual programme, set the MTS modeto Mono.Noise will be reduced and reception mayimprove.
Note: If you experience noise with a particularprogramme on whose channel reception isusually good, try setting MTS mode to Auto ,then switch to e Mono (monaural).
Selecting the Dual 1 or Dual 2 modeYou can hear only Dual 1 or Dual 2 soundselected, whenever bilingual programmes arereceived.
1 From the SOUND menu, press s or r toselect Dual.
2 Press v or w to select Dual 1 or Dual 2.Notes: • When the MTS setting is in Mono mode, the
Dual menu is not selectable.• The Dual menu setting status remains even if
the TV is turned off.
Adjusting the sound qualityYou can adjust the basic sound quality.
1 From the SOUND menu, press s or r to
select an item you want to adjust.2 Pressv orw to adjust the settings as required.
Selection v Pressing w
Bass weaker stronger
Treble weaker stronger
Balance decreases theright channel
decreases theleft channel
Adjusting Audio Level Offset
Sometimes there can be large changes involume when switching from an ATV channel oran external input. Using this feature reducesthese volume differences.
1 From the SOUND menu, press s or r toselect Audio Level Offset and press OK.
2 Press s or r to select an option and pressv or w to adjust the volume level.
FUNCTION menu
Panel LockPanel Lock disables the buttons on the TV. Allbuttons on the remote control can still be used.
1 From the FUNCTION menu, press s or r toselect Panel Lock .
2 Press v or w to select On or Off.Note: When Panel Lock is On , a reminder will appearwhen the buttons on the TV are pressed.
If the standby button is pressed, the TV willswitch off and can only be brought out of standbyby using the remote control.
Activating Blue ScreenWith the Blue Screen function On, the screenwill automatically turn blue and the sound will bemuted when no signal is being received.
1 From the FUNCTION menu, press s or r toselect Blue Screen.
2 Press v or w to select On or Off.
Adjusting the brightness of Side PanelYou can adjust the brightness of Side Panel in4:3, etc. mode.
1 From the FUNCTION menu, press s or r toselect Side Panel.
2 Press v or w to adjust the settings asrequired.
Changing the position
1 Enter the desired position number using theNumber buttons on the remote control.For positions below 10, use 0 and therequired number e.g., for position 1.
2 You can also change the position by using PUor P u.The position will be displayed on the screenwith the Mono/Stereo/Dual audio status.
Note: Changing positions between different format
channels takes several seconds.
8/18/2019 very important case
14/16
– 14 –
Switching between two positions
You can switch two positions without enteringactual position number each time.
1 Select the rst position you want to view.
2 Select the second position with the Number buttons (0-9).
3 Press . The previous channel will bedisplayed.
2 EFGH
3 IJKL Dual
Each time you press , the TV will switch backand forth between the two positions.
Displaying the on-screen information
1 Press to display the following on-screeninformation.
4 ABCD
The information will disappear in 6 seconds.• Position or external input mode selected• Position skip on/off information• Label (if set)• Mono/Stereo/Dual audio status
2 To erase the display instantly, press again.
Selecting stereo/bilingual
Selecting the stereo programmes1 When a stereo programme is received,d
Stereo appears.
10 ABCD Stereo
2 Press to select the stereo/monauralmode.d Stereo and e Mono appearcyclically on the screen.
Stereo
Selecting the bilingual programmes
1 When a bilingual programme is received,j Dual appears.
2 Press to select the sound to beheard. The sound differs according to thetransmission system: NICAM or German
stereo/bilingual broadcast.
Display
Sound to be heard
NICAMGerman stereo/
bilingual broadcast
j Dual 1 Sub I sound Main sound
J Dual 2 Sub II sound Sub sound
e Mono Main sound —
Note:
These settings are not stored in the TV memory.Selecting the monaural programmesIf sound distortion, interruptions or silencearises in the low sound volume level, setting the e Mono 2 mode will mitigate the problem.
1 When a monaural programme is received, eMono appears.
2 Press to select a monaural mode thatis easy to hear. e Mono 1 and e Mono 2 appear cyclically to the screen.
Note: On some cases, the reception of stereo/bilingualbroadcasts may not be possible after switchingon the e Mono 2 mode.
Setting the Sleep Timer menu
The Timer is especially useful if you want the TVto turn itself off after a selected period of time.
1 Press SLEEP and press v or w (SLEEP)to set the required Sleep Timer (Turn off the
TV).The timer display will set by 10 minutes, up to12 hours.
To cancel the Sleep Timer: Press v or w (SLEEP) until the timers set to00:00.
8/18/2019 very important case
15/16
– 15 –
Troubleshooting
Before calling a service technician, please checkthe following table for a possible cause of thesymptom and some solutions.
Symptom and solution
TV will not turn on• Make sure the power cord is plugged in, and
then press 1.• The remote control batteries may be dead.
Replace the batteries.
No picture, no sound• Check the aerial connections.
No sound, picture OK• The sound may be muted. Press2 +, − orU.
• The station may have broadcast difculties.Try another channel.
Poor sound, picture OK• The station may have broadcast difculties.
Try another channel.
Poor picture, sound OK• Check the aerial connections.• The station may have broadcast difculties.
Try another channel.• Adjust the PICTURE menu.
Poor reception of broadcast channels• Check the aerial connections.• The station may have broadcast difculties.
Try another channel.• Make sure the Colour System is properly set.
The brightness of the screen comesdown, or flickers of the screen arecaused, or some parts of the screen donot light up.
• When you just buy and start to use this TV,a ickering may be caused in the screen. Inthis case, switch off the TV, then switch on itagain to cure the condition.
• The cold cathode uorescent lamp used forthe back light on this TV has longevity. Whenthe brightness of the screen comes down,or the ickers of the screen are caused, orsome parts of the screen do not light up,it may reach the end of its life. Contact aservice technician.
Some pixels of the screen do not light up• The LCD display panel is manufactured
using an extremely high level of precision
technology, however, sometimes somepixels of the screen may be missing pictureelements or have luminous spots. This is nota sign of a malfunction.
The picture brightness varies when youdisplay switch the TV on.
• If you switch the TV on at 0°C and under,wait until the warms up.
Multiple images• The station may have broadcast difculties.
Try another channel.• Aerial reception may be poor. Use a highdirectional outdoor aerial.
• Check if the direction of the aerial has changed.
Poor colour or no colour• The station may have broadcast difculties.
Try another channel.• Adjust the Tint and/or Colour in the
PICTURE menu.
The remote control does not operate• Remove all obstructions between the remote
control and the remote control sensor on the TV.• The remote control batteries may be dead.
Replace the batteries.
Broadcast system
Broadcast transmission systems of eachcountry or region
Asia M.E.
Country or region Colour Sound
Bahrain, Kuwait, Israel,Oman, Qatar,United Arab Emirates,Yemen, etc.Indonesia, Malaysia,Singapore, Thailand, etc.
PAL B/G
China, Vietnam PAL D/K
China Hong Kong PAL I
Iraq, Islamic Republicof Iran, Lebanon, Saudi
Arabia, etc.
SECAM B/G
Russian Federation, etc. SECAM D/K
Myanmar, Republic of thePhilippines, etc.
NTSC M
Oceania
Country or region Colour Sound
Australia, New Zealand, etc. PAL B/G
Africa
Country or region Colour Sound
Republic of South Africa, etc. PAL I
8/18/2019 very important case
16/16
South America
Country or region Colour Sound
Chile, Colombia, etc. NTSC M
Note: PAL, SECAM and NTSC 3.58 (MHz) are differentcolour signal broadcast transmission systemsapplicable to different countries or region. NTSC4.43 (MHz) is used in special VCRs to playbackNTSC recorded video tapes through PAL TVequipment.
Specifications
LCD colour TVModel
19HV10 Series, 24HV10 Series,32HV10 Series
Power source 110-240 V AC, 50/60 Hz
Power consumption 19" : 22 W, 0.5 W24" : 48 W, 0.5 W32" : 85 W, 0.5 W
Dimensions 19" : 454 (W) 320 (H) 95 (D) mm24" : 568 (W) 387 (H) 125 (D) mm32" : 784 (W) 518 (H) 160 (D) mm
Mass (Weight)
19" : 3.0 kg24" : 4.5 kg32" : 8.0 kg
TV system (Aerial input) Channel coverage:
PAL B/G (CCIR) VHF 2 - 12
UHF 21 - 69
CATV X - Z+2, S1 - S41
PAL I (UK) VHF -
UHF 21 - 69
CATV -
PAL D/K (CHINA) VHF 1 - 12UHF 13 - 57
CATV Z1 - Z38
SECAM B/G (CCIR) VHF 2 - 12
UHF 21 - 69
CATV X - Z+2, S1 - S41
SECAM D/K (OIRT) VHF 1 - 12
UHF 21 - 69
CATV X1 - X19
NTSC M (US) VHF 2 - 13
UHF 14 - 69
CATVA6 - A1, A - W, AA -
ZZ, AAA, BBB
NTSC M (JAPAN) VHF 1 - 12UHF 13 - 62
CATV M1 - M10, S1 - S41
Special RF signal:NTSC 4.43 colour system5.5/6.0/6.5 MHz sound system
PAL 60 Hz colour system5.5/6.0/6.5 MHz sound system
COMPONENT VIDEO INPUT terminals (thesignal format)
480i, 480p, 576i, 576p, 720p (50/60 Hz),1080i (50/60 Hz)(These signal formats are converted to matchthe number of pixels of the LCD panel.)
Colour System PAL, SECAM, NTSC 3.58/4.43
Aspect ratio 16 : 9
Visible size (diagonal) 19" : 47.0 cm24" : 59.8 cm
32" : 80.0 cmNumber of pixels
19"/32" : 1366 (H) dots × 768 (V) dots24" : 1920 (H) dots× 1080 (V) dots
Audio power 5 W + 5 W
Speakers 19"/24" : Main 42 5 75 mm 2pcs.32" : Main 40 5 120 mm 2pcs.
Input / Output terminals
o (1) VIDEO Input
Phono jacks A/V
o (2)
COMPONENT /
VIDEO INPUT
Input
Standard video or Y
Component video Y, PB /CB, PR /CR
Phono jacks Audio L /
Mono +R
o HDMI Input (type A)
19 pin A/V Digital
Content type
Operating condition Temperature 0°C - 35°C
Humidity 20% - 80% (No moisturecondensation)
Supplied accessories Owner’s manual (1), Power cord (1),Remote control (1), Batteries (2), Screw (1)(- page 2) (only supplied on 32" models)
• Design and specications are subject tochange without notice.
• Never service or remodel the TV by yourself. Itmay expose you to a re hazard or dangerousvoltages.