1

Instruction Manual

VBRO WET & DRY COMMERCIAL VACUUM CLEANER

VBRO60 - 60 Litres (Model: BJ141-2000-60)

VBRO80 - 80 Litres (Model: BJ141-2000-80)

VBRO100 - 100 Litres (Model: BJ141-2000-100)

● Please read this Instruction Manual carefully before operation and follow all guidelines before using this vacuum cleaner.

● Please keep this Manual for future reference.

2

*** SAFETY RULES & CAUTIONS *** 1. Check before operation that the local power supply is the same as the specification on the rating label.

2. The machine is not suitable for picking up dusts, objects or liquids which are explosive, flammable,

poisonous, or in any way represent a danger to health.

3. Do not use machine in combustible or explosive areas in case the motor spark causes a fire.

4. Do not jam the air inlet mouth, in case temperature rises and damages the motor.

5. Do not collect sharp objects.

6. Do not collect objects which can easily attach on the filter such as calcareous powder, gesso and

graphite powder, they will block the ventilation and damage the motor.

7. Do not overturn the machine in case water goes into the motor and damages the motor.

8. Warning: If water outflows from air outlet mouth, do not overturn the machine. Water will go into the motor

and cause damage. Do not use this machine as a pump in case you damage the motor.

9. Do not trample or drag the hose.

10. Do not immerse the barrel cap into water or wash with water

11. In case the water goes into the electrophorus parts of the machine as this may cause injury. The correct

way should be: immerse the dishcloth firstly, then dry it. Finally, wipe the dirty part gently.

12. If the power cord needs to be replaced make sure it is replaced by a qualified technician

13. Check the mains cable to ensure it is ok before using the machine. Every care must be taken to avoid

damaging the mains cable. If the cable is broken, damaged or becomes loose in any way, then it must be

repaired or replaced before use. In case of replacement, the same quality of cable must be used.

14. All plugs and sockets used must be water-proof. Use only in 220v/240v plug and points.

15. Turn off the machine and remove the plug each time after using or when being repaired.

16. Keep the machine away from strong sunlight and high temperature places in case its plastic is distorted.

17. Always keep the machine as clean and dry as possible – don’t leave it for a long time with dust or water.

18. This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

19. Children should be supervised to ensure that they do not play with the appliance.

20. WARNING: If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

3

FEATURES & TECHNICAL SPECIFICATIONS Product Features

• Wet and Dry vacuum cleaner

• 2 x 1000 watt motor (motors work at the same time to give you stronger suction)

• Accessory storage on base

• Strong and durable Stainless Steel Tank

ATTACHMENTS & ACCESSORIES: 1 Suction hose

2 Short Connector

3 Long Connector

4 Metal tube

5 Dry floor brush

6 Wet floor brush

7 Crevice tool

8 Dust brush

Using the correct accessories:

• Dusting brush for windows, tables, etc.

• Wet floor nozzle for wet hard floor.

• Crevice nozzle for crevices, corners, etc.

TECHNICAL SPECIFICATIONS Model VBRO60 (BJ141-2000-60)

VBRO80 (BJ141-2000-80)

VBRO100 (BJ141-2000-100)

Power 2000W (twin motor)

Capacity 60L / 80L / 100L

Accessories 38mm

Voltage 220-240V

Hose Length 1.8m

Cable Length 7m

4

OPERATING INSTRUCTIONS 1. Make sure that the power supply is identical to that

shown on the rating label/voltage plate.

2. Insert the hose connector into the air inlet mouth as

picture shows, make sure the connector is tightly

fastened.

3. Connect all the accessories as picture shows.

4. Insert the plug into the supply socket.

5. Press the ON switch button to start the machine.

INSTRUCTIONS FOR DRY VACUUMING Before vacuuming dry dust, make sure that the HEPA filter and cloth filter bag is always fitted, regardless

of whether a paper dust bag is also used or not.

Empty dust from the tank as required.

The HEPA filter and cloth filter bag can be cleaned by beating or brushing it over a rubbish bin (these

must be replaced at regular intervals according to level of use)

In addition, the cloth filter bag can be washed with clean and warm water when it is covered with dust.

Make sure the cloth filter bag is completely dry before putting back in the machine.

When the tank is full of dust, this can cause the suction to decrease. You should turn the machine off and

disconnect the plug from the power socket before cleaning or maintenance.

Clean the dust away from the tank by unfastening the lid and lifting up the top cover. Then remove the

cloth filter bag and clean the dust inside the tank. Install the filter bag back and place the top cover on.

INSTRUCTIONS FOR WET VACUUMING Always ensure that the HEPA filter, cloth filter bag and paper bags are removed before vacuuming water.

When the water in the barrel is full, the float begins to work. The suction power will disappear when the

float is at the top of the barrel and the machine will make a noise which indicates the motor is running at a

high speed because there is no suction.

When the float is working and cutting off suction, you should turn off the machine and drain the dirty

water from the tank via the dump hose. The machine should start to work normally again.

If the machine becomes overturned you should turn it off, stand up the machine correctly and then turn

on the machine. When the float is working (cutting of suction when the water is full), the motor will be

damaged if you continue to use the machine. Under this circumstance, you should stop using the

machine and clean out the water.

5

ASSEMBLY Handrail Assembly 1. Put the①(handrail upper pipe, 1 pc) into the⑦(handrail under pipe, 2pcs)

2. There are 3 rows of positioning holes (③,④,⑤) in⑦(handrail under pipe, 2pcs), which is used to adjust

the suitable height. Please adjusted the①(handrail upper pipe, 1 pc) to the proper height position of the

positioning hole, then use the②(handrail screw, 2ps) and⑥ (nuts, 2pcs) to fix①and⑦.

3. When use the turnover function to clean the dust in the tank, please adjust the① (handrail upper pipe, 1

pc) to the positioning hole⑤.

Wheel Assembly 1. Put③( 2pcs) into⑤, then fixed②(2pcs) with⑤, put them in position①. Then use the screw to fix the④

(2pcs) and⑥(4pcs),

2. Fix the⑦(2pcs) and⑧(2pcs) into the corresponding position⑨tightly.

6

EXPLODED DIAGRAM

7

Cleanstar Pty Ltd

ABN: 51 121 002 104 ACN: 121 002 104

59 Radford Road, Reservoir VICTORIA 3073

Phone: (03) 9460 5655 Fax: (03) 9460 5666

Email: sales@cleanstar.com.au Web: www.cleanstar.com.au

CONDITIONS OF WARRANTY This document outlines the terms and conditions of warranty for your Cleanstar product. This is an important document that

should be kept with your proof of purchase documents in a safe place for future reference should you require service for your

product.

Thank you for purchasing your new Cleanstar product. We are confident this product will give you trouble-free use and excellent service,

provided the operator uses and maintains the product in accordance with the Instruction Manual. Please read the Instruction Manual

carefully before using the product for correct operation and maintenance procedures, and store it in a safe place for future reference.

1. This is a parts and labour warranty against faulty or defective parts, materials or workmanship in manufacturing, when the product

is used and operated in accordance with the Instruction Manual.

2. This product carries a 12 month (1 year) warranty period that commences from the original date of purchase by the first

user/purchaser, and is not transferable.

3. This warranty only applies to products purchased and used in Australia.

4. At all times during the warranty period, Cleanstar shall, at its sole discretion, determine whether repair, replacement or refund will

apply if the product has a valid warranty claim applicable to it.

5. The repair or replacement of the product under this warranty does not extend the original period of warranty.

6. Please note that this warranty will be voided in the following cases (which are not exhaustive) and the warranty does not apply to

the cost of replacing any parts of the product resulting from:

Accidental damage;

Normal wear and tear;

Neglect, misuse or physical abuse by the operator, including failure to properly maintain or service;

Any alterations, modifications or tampering with the product without the prior written consent of Cleanstar;

Incomplete or improper installation;

Incorrect, improper or inappropriate operation;

Insect or vermin infestation;

Power surges, electrical storm damage or incorrect power supply/voltage;

Excessive use or use for which this product has not been designed;

Vacuuming up toner, powders, glass, hazardous, flammable or corrosive materials, plaster dust, concrete dust and other

similar building or construction materials;

Failure to comply with the operating instructions contained in the Manual supplied with the product;

If the product is rented;

If the product is used outside of Australia;

8

If the product was serviced or repaired by anyone other than Cleanstar, or one of Cleanstar’s Authorised Service Agents

(ASA). Cleanstar is unable to accept any responsibility under this warranty for any repair work not carried out by an ASA or

from the use of non-genuine parts.

7. This warranty does not cover service calls, travelling time or consumable parts such as belts, dust bags, filters, hose or hose parts,

rods and wands, floor tools and accessories, motor brushes and other like consumable items, unless defective in manufacture. In

order to prolong the life of accessories and consumables, regular care and maintenance is recommended.

8. Please retain your original proof of purchase which will be required before you can make a claim under this warranty. If proof of

purchase can not be provided at the time of a warranty claim or service, any work carried out on the cleaner is chargeable.

9. Any transportation and delivery costs involved in the repair of defective parts shall be borne by the claimant. In all instances, unless

the product is transported by Cleanstar or a Cleanstar authorised representative, the product is transported at the owner’s cost and

risk while in transit to and from Cleanstar or its ASA.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or

refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the

goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits

conferred by this warranty are in addition to other rights and remedies under law in respect of the product to which this warranty relates.

TO INQUIRE ABOUT MAKING A CLAIM UNDER THIS WARRANTY, PLEASE FOLLOW THESE STEPS:

a) carefully check the Instruction Manual and the terms of this warranty;

b) have the name and model number of the appliance available;

c) have the proof of purchase available (ie. invoice, receipt, etc) showing where the appliance was purchased from and date of

purchase;

d) call Cleanstar on (03) 9460 5655 to speak to one of our customer service staff.