TR20EH3V-LINE® High-Cycle Compact Precision Injection Molding Machine

Electric hybrid direct pressure mold clampingUltra-high cycle molding Equipped with V-LINE® &

"LDDV"Developed the latest high-cycle compact precision injection molding machine, aiming for the world's fastest direct pressure mold clamping machine.Realized a reduction in the dry cycle time by 50% (compared with our existing product), and a re-duction in the molding cycle time, by weight sav-ing, low inertia, reduction of hydraulic fluid amount, and standardization of simultaneous op-eration.

Equipped with an electric hybrid direct pressure mold clamping system, combined with the advan-tages of the electric system and the hydraulic sys-tem. A symmetric mechanism was also adopted, which equalizes the expansion and contraction by the pressing force and the thermal expansion of the mold from the center.Realizes the latest high-cycle by maintaining high rigidity which maintains an accurate mold clamp-ing position, and smooth and quick transfer from mold closing to mold clamping.

Equipped with the unique V-LINE® and ultra-high response control injection valve LDDV* (Linear Direct

Double Valve), further enables molding of ultra-small precision components, and responds to various needs.Demonstrates outstanding performance in high added value molding across a wide range, in-cluding ultra-thin, fine shapes, and less strain.

(* When LP specification is selected)

New generation V-LINE® high-cycle injection molding machine in coexistence with the latest high-cycle and

stable molding greatly improved the yield rate for compact precision molded products

　● V-LINE is a registered trademark of Sodick Co., Ltd.Recycle Friendly Maintenancefree

Reducewaste

Create your future

Clamping Unit

Max. clamping force kN 196

Tie bar distance mm 310 × 260

Open daylight(Min. mold thickness + Max. stroke)

mm 400

Min. mold thickness mm 150

Ejector stroke mm 50

TR20EH3V-LINE® High-Cycle Compact Precision Injection Molding Machine

■ Machine Dimensions & Installation Drawing

■ Mold Installation Dimensions Drawing

■ Spec. Screw injection unit

Screw diameter mm 14 18

Plunger diameter mm 12 16

Max. injection pressure MPa 288 262

Theoretical injection volume cm3 4.5 14

Max. injection speed mm/s 500

Plasticization capacity kg/h 3.5 6.5

Machine dimensions / Weight

Machine dimensions(L x W x H)

mm 2629 x 925 x 1681

Machine weight kg 2100

400

10-φ12H7 Depth22

8-M6Tap Depth12

72-M12Tap Depth24

350300250200150100

201

Eject start position

Max. Mold open stroke Min. Mold thickness

Fixed platen

72-M12Tap Depth24

M10Tap Depth208-M6Tap Depth12

10-φ12H7 Depth22

400Movable platen

Safety door 350300250200150

100

430500

375375

B-

150250

100

205

260

410

300

250

200

150

100

180

360

332

φ54

φ40H

7

φ60H

7

φ22

φ16

150

200

250

300

310430B A

230st 0～50

Ejector stroke Unit stroke

85

85φ57

4-M12Resin feed, Bolt hole for hopper Bolt hole for take off robot6-M12Tap Depth20

30

30

20

120 120 Mold mounting surface

Main Spec of Nozzle

φ30.4φ23.2φ30.4φ23.2φ30.4φ23.2φ30.4φ23.2

φ1.5

φ2.0

φ2.5

φ3.0

Diameter ofNozzle Gate

Extension Spher R Outside Diamaterof Cover

3060306030603060

10

10

10

10

Unit: mm

92

5

46

04

65

75

0 37

53

75

1363 1237

2629Mold instalation face

34

0

40

04

05

34

53

40

34

5

Mounting layout drawing

1280

Mold instalation face

1155

52

14

09

15

36

Air supply Rc1/2OUTIN

Water supply Rc1/2

39

12

04

15

71

11

0

16

81

34

0 14

55

.5

422

Power supply socket

Power Cable Area More Than 8mm2

400

10-φ12H7 Depth22

8-M6Tap Depth12

72-M12Tap Depth24

350300250200150100

201

Eject start position

Max. Mold open stroke Min. Mold thickness

Fixed platen

72-M12Tap Depth24

M10Tap Depth208-M6Tap Depth12

10-φ12H7 Depth22

400Movable platen

Safety door 350300250200150

100

430500

375375

B-

150250

100

205

260

410

300

250

200

150

100

180

360

332

φ54

φ40H

7

φ60H

7

φ22

φ16

150

200

250

300

310430B A

230st 0～50

Ejector stroke Unit stroke

85

85φ57

4-M12Resin feed, Bolt hole for hopper Bolt hole for take off robot6-M12Tap Depth20

30

30

20

120 120 Mold mounting surface

Main Spec of Nozzle

φ30.4φ23.2φ30.4φ23.2φ30.4φ23.2φ30.4φ23.2

φ1.5

φ2.0

φ2.5

φ3.0

Diameter ofNozzle Gate

Extension Spher R Outside Diamaterof Cover

3060306030603060

10

10

10

10

Printed in Japan

3-12-1, Nakamachidai, Tsuzuki-ku, Yokohama, Kanagawa224-8522 JapanTEL: 81-45-942-3111 FAX: 81-45-943-7880

●�The export of Sodick's products and its related technologies (including software applications) is regulated under Japan's Foreign Exchange and Foreign Trade Control Law. In addition, because some of these products may be subject to re-export controls under the Export Administration Regulations (EAR) of the United States; please contact Sodick before offering or exporting these products overseas.

●This catalogue contains a photographic image that has been generated from 3DCG.●��Due to ongoing research, specifications are subject to change without prior notice.●The contents of this catalog is current as of October, 2015.

http://www.sodick.jp

R1014101.2015.11<01>