Using your Diagnostic StationUsing your Diagnostic Station

ADC by SunTech Adview features

• Overview of the ADC ADC by SunTech by SunTech AdviewAdview• Taking an automated BP measurement• Taking a manual BP measurement• Taking a temperature measurement

• Taking an SpO2 measurement

• Recalling the last reading• Clearing the last reading• Need help?

Contents

Overview of the ADC by SunTech Adview BP Module

Pressure column1 bar = 10mmHg

Automatic button

Manual button

Warning icon

Cuff/Hose Error icon

Systolic BP/Cuff pressure

Diastolic BP

Pulse rate icon

MAP icon

Pulse rate/Mean Arterial Pressure (MAP)

Contents

Overview of the fully configured ADC by SunTech

Adview

TemperatureMode button

Retention clip

Temperature Module

Signal quality

Contents

BP Module

SpO2 Module

Press the auto button to take an automatic measurement

OR

Press and hold the manual button to inflate the cuff, and take a traditional manual reading with a stethoscope

Taking a BP Measurement

Contents

Taking an automated BP measurement

1.1. Wrap cuff snugly around upper arm. Wrap cuff snugly around upper arm. Click here to visit the to visit the ADC website for further details on proper placement.ADC website for further details on proper placement.

2.2. Ask the patient to stay still and quiet, press and release the Ask the patient to stay still and quiet, press and release the automatic button to start an automatic measurement.automatic button to start an automatic measurement.

3.3. A measurement is displayed in about 35-40 secondsA measurement is displayed in about 35-40 seconds

Contents

Taking a manual BP measurement

1.1. Wrap cuff snugly around Wrap cuff snugly around upper arm and position your upper arm and position your stethoscope.stethoscope.

2.2. Press and hold the manual Press and hold the manual button to inflate the cuff to the button to inflate the cuff to the desired pressure.desired pressure.

3.3. Watch the pressure displayed Watch the pressure displayed and quickly release the and quickly release the button to deflate the cuff at button to deflate the cuff at 3mmHg/sec.3mmHg/sec.

1.1. When the measurement is determined, press the auto button to When the measurement is determined, press the auto button to completely deflate the cuff.completely deflate the cuff.

Contents

Taking a temperature measurement

1.1. Place a disposable cover on the blue probe; the display Place a disposable cover on the blue probe; the display shows the type of measurement, (oral). shows the type of measurement, (oral).

2.2. Wait for the device to beep.  Wait for the device to beep. 

3.3. Then, place the probe under the patient’s tongue; the Then, place the probe under the patient’s tongue; the posterior medial sublingual pocket is preferred for accuracy. posterior medial sublingual pocket is preferred for accuracy.

4.4. A “traveling dash” displays for 10-15 seconds until a reading A “traveling dash” displays for 10-15 seconds until a reading is displayed. is displayed.

Contents

Taking an SpO2 measurement

For the reusable finger sensor, insert the patient’s digit into the For the reusable finger sensor, insert the patient’s digit into the sensor; a “traveling dash” displays for 10-20 seconds until a sensor; a “traveling dash” displays for 10-20 seconds until a reading is displayed. The reading is updated every second.reading is displayed. The reading is updated every second.

Contents

Recalling the last reading

Note: Measurements are displayed for 2 minutes after which the display showsNote: Measurements are displayed for 2 minutes after which the display shows - - -

Press and hold the Automatic BP button for 2 - 3 seconds to Press and hold the Automatic BP button for 2 - 3 seconds to display the last measurement values.display the last measurement values.

Contents

Clearing the last reading

Note: If there are privacy concerns with regards to measurements on the display, you Note: If there are privacy concerns with regards to measurements on the display, you can clear the display. Once cleared, they cannot be recalled.can clear the display. Once cleared, they cannot be recalled.

Press and hold the Automatic BP button for 5 - 6 seconds to Press and hold the Automatic BP button for 5 - 6 seconds to clear the last measurement values.clear the last measurement values.

Contents