Technical ManualSectional Doors for Industry and CommerceSeries 40Issue 1.3.2004

Contents

2

Contents 2-3

STE 40 Single-skinned steel sections 4

TPU 40 Double-skinned steel sections 42/20 mm (625 and 750 mm high) 5

SPU 40 Double-skinned steel sections 42 mm (625 and 750 mm high) 6

SPU 40 with wicket door of double-skinned steel sections (625 and 750 mm high) 7

SPU 40 Double-skinned steel sections (375 and 500 mm high) 8

SPU 40 with wicket door of double-skinned steel sections (375 and 500 mm high) 9

TPU 40/SPU 40 Glazing heights (centre of window from FFL) for door section heights 500, 625 and 750 mm 10

TPU 40/SPU 40 Calculation of glazing heights (centre of window from FFL) 11

APU 40 N/TAP 40 Aluminium extrusions with double-skinned steel bottom section 12

APU 40 B Aluminium extrusions with double-skinned steel bottom section 13

APU 40 N/TAP 40 750 mm high bottom section with wicket door 14

APU 40 N/TAP 40 500 mm high bottom section with wicket door 15

APU 40 N/TAP 40 1000 mm high bottom section with wicket door 16

APU 40 N/TAP 40 1500 mm high bottom section with wicket door 17

ALR 40 N/TAR 40 Standard aluminium extrusions with or without thermal breaks 18

ALR 40 B Standard aluminium extrusions 19

ALR 40 N/TAR 40 with wicket door 20

ALS 40 Standard aluminium extrusions 21

Side doors NT 60 22

Side doors Arrangements and fitting options 23

Track application N Normal tracks 24

Track application ND Normal tracks with inclination 25

Track application NH Normal tracks with minimum high-lift 26

Contents

3

Track application NS Normal tracks with double radius 2 x 45° 27

Track application H High-lift tracks 28

Track application HD High-lift tracks with inclination 29

Track application HS High-lift tracks with double radius 2 x 45° 30

Track application HU High-lift tracks with torsion spring assembly above opening height 31

Track application L Low-headroom tracks 32

Track application LD Low-headroom tracks with inclination 33

Track application V Vertical tracks 34

Track application VU Vertical tracks with torsion spring assembly above opening height 35

Sideroom clearances 36

Headroom details 37

Floor Details 38

Hand chain hoist 39

Hand pulley with rope or round steel chain 40

Track supports 41

Chain drive ITO 400 42

Shaft operator WA 400 as frame-mounted operator 43

Shaft operator WA 400 with chain drive operator 44

Shaft operator WA 400 for central mounting 45-47

Door leaf speeds WA 400 47

Details of door leaf and fitting clearances as well as installation examples are shown in this Technical Manual.

Copyright. No reproduction, even in part, is allowed without our permission.All dimensions in mm.Subject to design alterations.

38,5

500

R60

635

245

56

38,5

500

52

375/

500

56,5

91

76

710

320

Sectional Door STE 40Single-skinned steel sections

Door leaf: Consisting of single-skinned, hot galvanized steel sections with uniform horizontal ribbing, stucco-embossed. Door sections 375 mm and 500 mm high, with an overall thickness of 42 mm. All door sections with finger-trap protection and polyester-primed surface protection. Ventilation slots in the bottom section optional. Standard (NF) window sections of anodized aluminium extrusions or individual vision panels only possible as shown below. Arrangement of vision panels subject to the reinforced sections located internally.

External view

Size range: Within the limits shown below, any door width can be made in 10 mm increments but door heights can only be the ordering heights as quoted (subject to the minimum ceiling height). Intermediate sizes only possible when using aluminium-framed window sections!

Vision panels type AWindow section NF

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2

2

4

3

3

6

4

4

8

5

5

10

6

6

12

7

7

14

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

– 141 132 123 11– 131 122 113 10– 121 112 103 9– 111 102 93 8– 101 92 83 7– 91 82 73 6– 81 72 63 5– 71 62 53 4– 61 52 43 3– 51 42 33 2– 41 3

[ A ]

5

[A] No. of door sections TH = 375 mm and TH = 500 mm

Note: Aluminium window sections with field spacing to B are supplied with broad rails (91 mm).

4

Are

a fo

r w

ind

ow

sect

ions

Are

a fo

r vi

sion

pan

els

On request

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail width 91

2 (up to 3330 mm) 3 (up to 5000 mm) 4 (up to 6670 mm)

No. of infills/fields per section N

No. of infills/fields per section B

Number of vision panelsper sectionNumber of ventilation grilles.Ventilation cross section 40 cm2 per grille

Rail width 52

5

Sectional Door TPU 40Double-skinned steel sections(625 and 750 mm high)

Door leaf: Consisting of double-skinned hot galvanized steel sections with uniform horizontal ribbing, stucco-embossed. Door sections 625 and 750 mm high, with an overall thickness of 42/20 mm. All door sections with finger-trap protection and polyester-primed surface protection. Ventilation grilles optional. Window sections of anodized aluminium extrusions in standard version (NF) or alternatively compound glazing sections, only possible as shown below. Fewer compound windows or different arrangements are possible subject to the minimum distances.

External view

Size range: Within the limits shown below, any door width can be made in 10 mm increments observing the ordering heights in 125 mm modules as quoted (subject to the minimum ceiling height). Intermediate sizes using aluminium-framed window sections or shortened top door section possible.

R60

635

245

710

R5

602

132

38,5

625/

750

R60

370

725680 800

38,5

625/

750

5256,5

625/

750

91

76

210

445

320

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2

4

3

6

4

8

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

[ A ]

*

4 65 5– 91 82 73 64 55 4– 81 72 63 54 45 3– 71 62 53 44 35 2– 61 52 43 34 25 1– 51 42 33 24 15 –– 41 32 23 14 –4 –– 31 22 13 –

5

10

2 (2750-3330 mm) 3

Window section (NF)

2

A, D3452

E345

[A] No. of section TH = 625 mm and TH = 750 mm

When using a shaft operator (installation example 5), the door lock is always on the side opposite the operator

Compound glazing type A

Compound glazing type ECompound glazing type D

Note: Aluminium window sections with field spacing to B are supplied with broad rails (91 mm).

On request

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 Width

No. of infills/fields per section N

No. of infills/fields per section B

Number of compound windowsper section (see table 1)

Number of ventilation grilles.Ventilation cross section 40 cm2 per grille

* Top door section shortened to 500 mm

Are

a fo

r w

ind

ow s

ec-

tions

min. 125 min. 80

Are

a fo

r co

mp

ound

glaz

ing

min. 80min. 125

Type No. Door width

2000 to 2500 mm

2510 to 3500 mm

3510 to 4500 mm

4510 to 5000 mm

2000 to 2740 mm

2750 to 3640 mm

3650 to 4530 mm

4540 to 5000 mm

min. 125min. 80

Table 1: number of compound windows per door section

Sectional Door SPU 40Double-skinned steel sections(625 and 750 mm high)

6

Door leaf: Consisting of double-skinned hot galvanized steel sections with uniform horizontal ribbing, stucco-embossed. Door sections 625 and 750 mm high, with an overall thickness of 42 mm. All door sections with finger-trap protection and polyester-primed surface protection. Ventilation grilles optional. Window sections of anodized aluminium extrusions in standard version (NF) or with thermal breaks (WF) (only with field spacing to type N) or alternatively compound glazing sections, only possible as shown below. Fewer compound windows or different arrangements are possible subject to the minimum distances. If a wicket door is included, note the position!

External view

Size range: Within the limits shown below, any door width can be made in 10 mm increments observing the ordering heights in 125 mm modules as quoted (subject to the minimum ceiling height). Intermediate sizes using aluminium-framed window sections or shortened top door section possible.

Compound glazing type C Compound glazing type D Compound glazing type E

R5

602

132

38,5

625/

750

244

38,5

625/

750

370

725

635

R60

245

38,5

625/

750

5256,5

625/

750

710

680 800

76

91

210

320

320

445

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2

4

3

6

4

8

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5

10

*

[ A ]4 65 5– 91 82 73 64 55 4– 81 72 63 54 45 3– 71 62 53 44 35 2– 61 52 43 34 25 1– 51 42 33 24 15 –– 41 32 23 14 –4 –– 31 22 13 –

2 (2750-3330 mm) 3

Window section (NF or WF) Compound glazing type A

[A] No. of door sections TH = 625 mm and TH = 750 mm

2A, C, D 3

452

E 345

When using a shaft operator (installation example 5), the door lock is always on the side opposite the operator

Note: Aluminium window sections with field spacing to B are supplied with broad rails (91 mm).

On request

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 Width

No. of infills/fields per section N

No. of infills/fields per section B**

Number of compound windowsper section (see table 1)

Number of ventilation grilles.Ventilation cross section 40 cm2 per grille

* Top door section shortened to 500 mm** for aluminium frames type NF only

Are

a fo

r w

ind

ow s

ec-

tions

Are

a fo

r co

mp

ound

glaz

ing

min. 125 min. 80

Are

a fo

r co

mp

ound

glaz

ing

min. 125 min. 80min. 125 min. 80

Type No. Door width

2000 to 2500 mm

2510 to 3500 mm

3510 to 4500 mm

4510 to 5000 mm

2000 to 2740 mm

2750 to 3640 mm

3650 to 4530 mm

4540 to 5000 mm

Table 1: number of compound windows per door section

Sectional Door SPU 40with wicket door of double-skinned steel sections(625 and 750 mm high)

7

Wicket door: Only to be installed into the central areas of the sectional door. Cannot be installed into the side areas of the sectional door. Only opening outwards. LH or RH hinged. Window sections (NF or WF) from 625/750 mm above FFL, alternatively compound windows from 625/750 mm (not in the wicket door section housing the lock) above FFL, available on request. Ventilation grilles are not possible in wicket doors. Note: for ordering heights 2000, 2125 and 2250 the structural opening height must not be lower than the door height.

External view

Size range: Within the limits shown below, any door width can be made in 10 mm increments observing the ordering heights in 125 mm modules as quoted (subject to the minimum ceiling height). Intermediate sizes possible using aluminium-framed window sections or shortened door section above wicket door.

625

/750

38,5

625

/750

625

/750

1080

,5

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2

4

3

4

4

6

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5

8

22052205220522052205220522052205220522052205220522052205220522052205220522052080220522052205220520801955220522052205208019551830220522052080195518301830220520801955

[ D ]

*

[ A ]4 65 5– 91 82 73 64 55 4– 81 72 63 54 45 3– 71 62 53 44 35 2– 61 52 43 34 25 1– 51 42 33 24 15 –– 41 32 23 14 –4 –– 31 22 1

[A] No. of door sections TH = 625 mm and TH = 750 mm

[D] Passage heights (DHS) of wicket door to ordening height

When using a shaft operator (installation example 5), the door lock is always on the side opposite the operator

Note on the fitting of compound windows **

For door widths from 2510 - 2640 mm only one compound window can be fitted into the wicket door. Compound windows to the left or right of the wicket door is not possible for this size. Compound windows type E within and next to the wicket door on request!

Clear passage width (LDBS) =

* Rail 52 mm =

Rail 91 mm =

* Also for doors without glazing frame

Door width - 61

number of fields across -137

Door width - 61

number of fields across -98

On request

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 Width

Number of infills/fieldsper section

Number of compound windowsper door section (see table 1) **Number of ventilation grillesVentilation cross section 40 cm2 per grille

* Top door section shortened to 500 mm

Pas

sage

hei

ght

(DH

S)

LZ = Width between frame

LDBS

Windows on request

Threshold height = 200

Sectional Door SPU 40Double-skinned steel sections(375 and 500 mm high)

8

Door leaf: Consisting of double-skinned hot galvanized steel sections with uniform horizontal ribbing, stucco-embossed. Door sections 375 and 500 mm high, with an overall thickness of 42 mm. All door sections with finger-trap protection and polyester-primed surface protection. Ventilation grilles optional. Window sections of anodized aluminium extrusions in standard version (NF) or with thermal breaks (WF) (only with field spacing to type N) or alternatively compound glazing sections, only possible as shown below. Fewer compound windows or different arrangements are possible subject to the minimum distances. If a wicket door is included, note the position!

External view

Size range: Within the limits shown below, any door width can be made in 10 mm increments observing the ordering heights in 125 mm modules as quoted (subject to the minimum ceiling height). Intermediate sizes possible using aluminium-framed window sections or shortened door section above wicket door.

Compound glazing type C Compound glazing type D

244

R5

38,5

500

602

132

38,5

500

5256,5

375/

500

91 76

680

R60

635

245

710

320

320

210

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2

2

4

3

3

6

4

4

8

5

5

10

6

6

12

7

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

7

14

8

16

– 141 132 123 11– 131 122 113 10– 121 112 103 9– 111 102 93 8– 101 92 83 7– 91 82 73 6– 81 72 63 5– 71 62 53 4– 61 52 43 3– 51 42 33 2– 41 3

[ A ]

8

2 (2750-3330 mm) 5

[A] No. of door sections TH = 375 mm and TH = 500 mm

Note: window section (WF) only up to 7000 mm wide

Window section (NF or WF) Compound glazing type A

Note: Aluminium window sections with field spacing to B are supplied with broad rails (91 mm).

On request

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 Width

3 (up to 5000 mm)

No. of infills/fields per section N

No. of infills/fields per section B*

Number of compound windowsper section (see table 1)

Number of ventilation grillesVentilation cross section 40 cm2 per grille

** for aluminium frames type NF only

Are

a fo

r 50

0 m

m

win

dow

sec

tions

min. 125min. 80

Fitt

ing

area

for

com

pou

nd w

ind

ows

min. 125 min. 80

4 (up to 6670 mm)

Rail width 52 Rail width 91

Sectional Door SPU 40with wicket door of double-skinned steel sections(375 and 500 mm high)

9

Wicket door: Only to be installed into the central areas of the sectional door. Cannot be installed into the side areas of the sectional door. Only opening outwards. LH or RH hinged. Window sections (NF or WF) from 500 mm above FFL, alternatively compound glazing from 500 mm (not in the wicket door section housing the lock) above FFL, available on request. Ventilation grilles are not possible in wicket doors. Note: for ordering heights 2000 and 2125 the structural opening height must not be lower than the door height.

External view

Size range: Within the limits shown below, any door width can be made in 10 mm increments observing the ordering heights in 125 mm modules as quoted (subject to the minimum ceiling height). Intermediate sizes possible using aluminium-framed window sections or shortened door section above wicket door.

500

38,5

500

500

500

830,

5

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2

2

4

3

3

4

4

4

6

5

5

8

6

6

10

7

7

12

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

– 141 132 123 11– 131 122 113 10– 121 112 103 9– 111 102 93 8– 101 92 83 7– 91 82 73 6– 81 72 63 5– 71 62 53 4– 61 52 4– 5– 51 42 3– 4– 4

[ A ]

Note on the fitting of compound glazing **

For door widths from 2510 - 2640 mm only one compound window can be fitted into the wicket door. This size does not allow the fitting of compound windows to the left or right of the wicket door.

Passage height (DHS) =

ordering height 2000 = 1955ordering height 2125 = 2080ordering height 2250 = 1830ordering height 2625 = 2080from ordering height 2375 = 1955

[A] No. of door sections TH = 375 mm and TH = 500 mm

Clear passage width (LDBS) =

* Rail 52 mm =

Rail 91 mm =

* Also for doors without glazing frame

Door width - 61

number of fields across-137

Door width - 61

number of fields across-98

Pas

sage

hei

ght

(DH

S)

LZ = Width between frame

LDBS

On request

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 Width

Number of infills/fieldsper section

Number of compound windowsper door section

Number of ventilation grillesVentilation cross section 40 cm2 per grille

Rail width 91Rail width 52

Windows on request

Threshold height = 200 Threshold height = 325

Windows from 625 mm

Glazing Heights for Matching External Appearance(centre of window from FFL)for door section heights 500, 625 and 750 mm

10

7000

6875

6750

6625

6500

6375

6250

6125

6000

5875

5750

5625

5500

5375

5250

5125

5000

4875

4750

4625

4500

4375

4250

4125

4000

3875

3750

3625

3500

3375

3250

3125

3000

2875

2750

2625

2500

2375

2250

2125

2000

1875

1155

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

1280

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

1530

X

X

X

X

X

X

X

X

X

X

X

X

1655

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

1780

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

1905

X

X

X

X

X

X

X

X

2030

X

X

X

X

X

X

X

X

X

X

X

X

X

X

2155

X

X

X

X

X

X

X

X

X

X

X

X

X

X

2280

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

2405

X

X

X

X

X

X

X

X

2530

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

2655

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

Glazing heights with matching external appearance of compound windows type A, C* and D.

* Type C only with SPU 40

Ordering height (RM)

Glazing heights (centre of window from FFL)

Calculation of Glazing Heights(centre of window from FFL)for door section heights 500, 625 and 750 mm

11

Calculation of glazing heights for compound windows type A, type C*, type D and type E.For number of door sections and glazing areas see door type! The figures below correspond to a section with an overall thickness of 42 mm.

750

220

X

750

220

X

750

220

X

750

282,

5X

625

220

X

625

220

X

625

220

X

625

282,

5X

500

220

X

500

220

X

500

220

X

625

1030

750

6022

0

38,5

625

1155

750

6034

5

38,5

Glazing height type A, C, D

O1 = x + 220O2 = x + 220 + 125O3 = x + 220 + 250

Glazing height type E

O1 = x + 282,5O2 = x + 282,5 + 125

Door section height 750 mm(TPU 40 and SPU 40)

X = sum of door section heights + 60 mm

from FFL

* = type C only with SPU 40

Glazing height type A, C, D

O1 = x + 220O2 = x + 220 + 125

Glazing height type E

O1 = x + 282,5

Door section height 625 mm(TPU 40 and SPU 40)

X = sum of door section heights + 60 mm

from FFL

* = type C only with SPU 40

Glazing height type A, C, D

O1 = x + 220

Glazing height type E

Not possible!

Door section height 500 mm(STE 40 and SPU 40)

X = sum of door section heights + 60 mm

from FFL

* = type C only with SPU 40

1st option, in 2nd door section 625 mm at position 1: glazing height = 750+60+220 = 1030 mm from FFL

2nd option, in 2nd door section 625 mm at position 2: glazing height = 750+60+220+125 = 1155 mm from FFL

3rd option, in 3rd door section 625 mm at position 1: glazing height = 750+625+60+220 = 1655 mm from FFL

4th option, in 3rd door section 625 mm at position 2: glazing height = 750+625+60+220+125 = 1780 mm from FFL

etc.

Calculation example

Given: door type TPU 40; ordering height (RM) = 3250 mm; glazing type A; for arrangement see number of door sections below (see table of door types) Door section 625 mm = x 4 Door section 750 mm = x 1

Type A Type C* Type D Type E

FFL

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

Type A Type C* Type D Type E

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

Type A Type C* Typ D

Cen

tre

of w

ind

ow

from

FFL

Cen

tre

of w

ind

ow

from

FFL

1st option 2nd option

FFL

FFL

FFL

12

Sectional Door APU 40 N, TAP 40Door leaf of aluminium extrusionsDouble-skinned bottom section

Door leaf: Bottom section of hot galvanized sections, infilled with polyurethane foam, 750 (standard version) 500, 1000 or 1500 mm high, with uniform horizontal ribbing, stucco-embossed. Polyester primed surface protection. Other door sections with glazing of anodized aluminium extrusions in the standard version (APU 40 N) or with thermal breaks (TAP 40). Overall thickness 42 mm. All door sections with finger-trap protection. Infill: APU 40 N, TAP 40 clear acrylic double panes, 16 mm thick. Ventilation grilles in the bottom section optional.

External view

Size range: Within the limits shown below, any door width and height can be made in increments of 10 mm (subject to the minimum ceiling height).

750

38,5

60

56,5

120

52 7691

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2

4

3

6

4

8

5

10

6

12

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

1875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

7

14

8

16

9

8

7

6

5

4

3

2

[ D ]7000

65406530

57905780

50405030

42904280

35403530

27902780

204020301875

9

8

7

6

5

4

3

2

7000

62906280

55405530

47904780

40404030

32903280

25402530

1875

8

7

6

5

4

3

2

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

1875

8

7

6

5

4

3

2

1

n n n n

[ A ] [ B ] [ C ]

When using a shaft operator installation example 5, the door lock is always on the side opposite the operator

TH =door height - bottom section - 35

No. of window sections

No. of window sections

[A] bottom section

750 mm (standard)

[B] bottom section 500 mm

[C] bottom section 1000 mm

[D] bottom section 1500 mm

THTH

THTH

On request

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail width 91Rail width 52

up to 7000 with TAP 40

n = No. of aluminium sections

Height Height Height HeightNumber of infills/fieldsper section

Number of ventilation grilles Venti- lation cross section 40 cm2 per grille

13

Sectional Door APU 40 BDoor Leaf of aluminium extrusionsDouble-skinned bottom section

Door leaf: Bottom section of hot galvanized sections, infilled with polyurethane foam, 750 (standard version), 500, 1000 or 1500 mm high, with uniform horizontal ribbing, stucco-embossed. Polyester-primed surface protection. Other door sections with glazing of anodised aluminium extrusions in the standard version (NF). Overall thickness 42 mm. All door sections with finger-trap protection. Infill: clear acrylic double panes, 16 mm thick. Ventilation grilles in the bottom section optional.

External view

Size range: Within the limits shown below, any door width and height can be made in increments of 10 mm (subject to the minimum ceiling height).

750

38,5

6012

0

7691

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

6 8 10 12

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

1875

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

14 16

9

8

7

6

5

4

3

2

[ D ]7000

65406530

57905780

50405030

42904280

35403530

27902780

204020301875

9

8

7

6

5

4

3

2

7000

62906280

55405530

47904780

40404030

32903280

25402530

1875

8

7

6

5

4

3

2

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

1875

8

7

6

5

4

3

2

1

n n n n

[ A ] [ B ] [ C ]

5

When using a shaft operator (installation example 5), the door lock is always on the side opposite the operator

TH =door height - bottom section - 35

No. of window sections

No. of window sections

[A] bottom section 750 mm (standard)[B] bottom section 500 mm[C] bottom section 1000 mm[D] bottom section 1500 mm

THTH

THTH

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2750 WidthRail width 91

Height Height Height Height

n = No. of window sections

On request

Number of infills/fields per section

Number of ventilation grilles, ventila-tion cross-section 40 cm2 per grille

2 (up to 3330 mm) 3 (up to 5000 mm) 4 (up to 6670 mm)

14

Sectional Door APU 40 N, TAP 40Bottom section 750 mm highwith wicket door

Wicket door: Depending on the door type, consisting of anodised aluminium extrusions in the standard version or with thermal breaks, installed into the central areas of the door. Cannot be installed into the side areas of the sectional door. Only opening outwards. LH or RH hinged. Ventilation grilles are not possible in wicket doors. Note: if the wicket door has the same number of sections as the sectional door, the structural opening height must not be lower than the door height (RM).

External view:

Size range: Within the limits shown below, any door width can be made in 10 mm increments (subject to the minimum ceiling height).

750

38,5

56,5 52 91

60

120

76

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2

4

3

4

4

6

5

8

6

10

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

2000

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7

12

9

8

7

6

5

4

3

2

2

2

2

2

2

2

2

3

2

n n1

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

20862058219621652134210320712040219521592124208820522016219321522110206820271985219121412091204119911941218821252063200019381875218220962015193218482295217020451920

24302420

Passage height (DHS) =

n1 x TH + (bottom section height - 45)

n1 = No. of window sections in the wicket door

When using a shaft operator installation example 5, the door lock is always on the side opposite the operator

Height of handle on request

Clear passage width (LDBS) =

Rail 52 mm = Door width - 61

No. of fields -137

Rail 91 mm = Door width - 61

No. of fields -98

THTH

THTH

Pas

sage

hei

ght

(DH

S)

LZ = Width between frame

LDBS

Hei

ght

of h

and

le

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail width 52

Height DHS Height

n = No. of window sectionsn1 = No. of window sections in the wicket door

On request

Rail width 91

Threshold height = 200Threshold height

= 325

Number of infills/fieldsper section

Number of ventilation grilles. Ventila- tion cross section 40 cm2 per grille

RM

15

Sectional Door APU 40 N, TAP 40Bottom section 500 mm highwith wicket door

Wicket door: Depending on the door type, consisting of anodised aluminium extrusions in the standard version or with thermal breaks, installed into the central areas of the door. Cannot be installed into the side areas of the sectional door. Only opening outwards. LH or RH hinged. Ventilation grilles are not possible in wicket doors. Note: if the wicket door has the same number of sections as the sectional door, the structural opening height must not be lower than the door height (RM).

External view:

Size range: Within the limits shown below, any door width can be made in 10 mm increments (subject to the minimum ceiling height).

500

38,5

56,5 52

60

91 76

120

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2

4

3

4

4

6

5

8

6

10

7000

65406530

57905780

50405030

42904280

35403530

27902780

20402000

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7

12

9

8

7

6

5

4

3

2

2

2

3

2

3

2

3

2

3

2

3

2

3

2

n n1

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

18921864183618081946191518841853182124581945190918741838180224221943190218601818243823751941189118412459238424721938187518132398230422101932184824202295217020451920

59205910

52505240

45804570

39003890

32303220

25602550

Passage height (DHS) =

n1 x TH + (plinth height - 45)

n1 = No. of window sections in the wicket door

When using a shaft operator installation example 5, the door lock is always on the side opposite the operator

Height of handle on request

Clear passage width (LDBS) =

Rail 52 mm = Door width - 61

No. of fields -137

Rail 91 mm = Door width - 61

No. of fields -98

THTH

THTH

Pas

sage

hei

ght

(DH

S)

LZ = Width between frame

LDBS

Hei

ght

of

hand

le

TH

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail width 52

Height RM DHS Height

n = No. of window sectionsn1 = No. of window sections in the wicket door

On request

Rail width 91

Threshold height = 200

Number of infills/fieldsper section

Number of ventilation grilles. Ventila-tion cross section 40 cm2 per grille

16

Sectional Door APU 40 N, TAP 40Bottom section 1000 mm highwith wicket door

Wicket door: Depending on the door type, consisting of anodised aluminium extrusions in the standard version or with thermal breaks, installed into the central areas of the door. Cannot be installed into the side areas of the sectional door. Only opening outwards. LH or RH hinged. Ventilation grilles are not possible in wicket doors. Note: if the wicket door has the same number of sections as the sectional door, the structural opening height must not be lower than the door height (RM).

External view:

Size range: Within the limits shown below, any door width can be made in 10 mm increments (subject to the minimum ceiling height).

1000

38,5

56,5 52 91

60

76

120

2

2

2

2

2

2

2

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2

4

3

4

4

6

5

8

6

10

7000

62906280

55405530

47904780

40404030

32903280

25402530

2000

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7

12

8

7

6

5

4

3

2

n n1

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

24462415238423532321229024452409237423382302226624432402236023182277223524412391234122912241219124382375231322502188212524322348226521822098201524202295217020451920

When using a shaft operator installation example 5, the door lock is always on the side opposite the operator

Passage height (DHS) =

n1 x TH + (plinth height - 45)

n1 = No. of window sections in the wicket door

Clear passage width (LDBS) =

Rail 52 mm = Door width - 61

No. of fields -137

Rail 91 mm = Door width - 61

No. of fields -98

Height of handleLZ ≤ 5500 = 830,5LZ > 5500 = on request

THTH

THTH

Pas

sage

hei

ght

(DH

S)

LZ = Width between frame

LDBS

Hei

ght

of

hand

le

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail width 52

Height RM DHS

n = No. of window sectionsn1 = No. of window sections in the wicket door

On request

Rail width 91

Threshold height = 200

Number of infills/fieldsper section

Number of ventilation grilles. Ventila-tion cross section 40 cm2 per grille

Threshold height = 325

Sectional Door APU 40 N, TAP 40Bottom section 1500 mm highwith wicket door

Wicket door: Depending on the door type, consisting of anodised aluminium extrusions in the standard version or with thermal breaks, installed into the central areas of the door. Cannot be installed into the side areas of the sectional door. Only opening outwards. LH or RH hinged. Ventilation grilles are not possible in wicket doors.

External view:

Size range: Within the limits shown below, any door width can be made in 10 mm increments (subject to the minimum ceiling height).

1500

38,5

56,5 91

120

60

52 76

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375

2

4

3

4

4

6

5

8

6

10

700067906780

60406030

52905280

45404530

37903780

30403030

2290

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7

12

8

7

6

5

4

3

2

1

1

1

1

1

1

1

n n1

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375

21382123220021822164214621292111219921782158213721162095219821732148212320982073219621652134210320712040219321522110206820271985218821252063200019381875

When using a shaft operator installation example 5, the door lock is always on the side opposite the operator

Passage height (DHS)

n1 x TH + (bottom section height - 45)

n1 = No. of window sections in the wicket door

Clear passage width (LDBS) =

Rail 52 mm = Door width - 61

No. of fields -137

Rail 91 mm = Door width - 61

No. of fields -98

Height of handle on request

17

THTH

TH

Pas

sage

hei

ght

(DH

S)

LZ = Width between frame

LDBS

Hei

ght

of h

and

le

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail width 52

Height RM DHS

n = No. of window sectionsn1 = No. of window sections in the wicket door

On request

Rail width 91

Threshold height = 200

Number of infills/fieldsper section

Number of ventilation grilles. Ventila-tion cross section 40 cm2 per grille

Threshold height = 325

18

Sectional Door ALR 40 N, TAR 40Door leaf of standard aluminium extrusionsor aluminium extrusions with thermal breaks

Door leaf: Door sections of anodised aluminium extrusions in the standard version (NF) for door type ALR 40 N or with thermal breaks (WF) for door type TAR 40. Overall thickness 42 mm. All door sections with finger-trap protection. ALR 40 N: bottom door section consisting of polyurethane foam insulated infill with stucco-embossed 16 mm Aluman sheet on both sides, other door sections with 16 mm clear acrylic double panes. Ventilation grilles in the bottom section optional.

External view:

Size range: Within the limits shown below, any door width and height can be made in 10 mm increments (subject to the minimum ceiling height).

38,5

60

56,5 52

120

91 76

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2

4

3

6

4

8

5

10

6

12

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

1875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

10

9

8

7

6

5

4

3

n7

14

8

16

When using a shaft operator installation example 5, the door lock is always on the side opposite the operator

TH = Door height - 35

No. of window sections

THTH

TH

LZ = Width between frame

THTH

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail height 52

Height

n = number of window sections

On request

Rail height 91

up to 7000 width TAR 40

Number of infills/fields per section

Number of ventilation grilles. Ventila-tion cross section 40 cm2 per grille

19

Sectional Door ALR 40 BDoor leaf of standard aluminium extrusions

Door leaf: Door sections of anodised aluminium extrusions in the standard version (NF). Overall thickness 42 mm. All door sections with finger-trap protection. Bottom door section with polyurethane foam insulated infill with stucco-embossed 16 mm Aluman sheet on both sides. Other door sections with 16 mm clear acrylic double panes. Ventilation grilles in the bottom section optional.

External view:

Size range: Within the limits shown below, any door width and height can be made in 10 mm increments (subject to the minimum ceiling height).

38,5

6012

0

7691

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

6 8 10 12

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

1875

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

10

9

8

7

6

5

4

3

n

14 16

5

When using a shaft operator (installation example 5), the door lock is always on the side opposite the operator

TH = Door height - 35

No. of window sections

THTH

TH

LZ = Width between frame

THTH

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2750 WidthRail height 91

Height

n = number of window sections

On request

Number of infills/fields per section

Number of ventilation grilles. Ventila-tion cross section 40 cm2 per grille

2 (up to 3330 mm) 3 (up to 5000 mm) 4 (up to 6670 mm)

20

Sectional Door ALR 40 N, TAR 40with wicket door

Wicket door: Depending on the door type, consisting of anodised aluminium extrusions in the standard version or with thermal breaks, installed into the central areas of the door. Cannot be installed into the side areas of the sectional door. Only opening outwards. LH or RH hinged. Ventilation grilles are not possible in wicket doors. Note: if the wicket door has the same number of sections as the sectional door, the structural opening height must not be lower than the door height (RM).

External view:

Size range: Within the limits shown below, any door width can be made in 10 mm increments (subject to the minimum ceiling height).

38,5

60

56,5 52 91 76

120

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

2

4

3

4

4

6

5

8

6

10

700067906780

60406030

52905280

45404530

37903780

30403030

22902280

2000

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7

12

10

9

8

7

6

5

4

3

3

3

3

3

3

3

3

4

3

n n1

70006875675066256500637562506125600058755750562555005375525051255000487547504625450043754250412540003875375036253500337532503125300028752750262525002375225021252000

20452007219321522110206820271985219221452098205120041958219021362083202919761922218821252063200019381875218421092034195918841809217920851991189818042295217020451920

25002490

Passage height (DHS) =

n1 x TH - 45

n1 = No. of window sections in the wicket door

When using shaft operator installation example 5, the door lock is always on the side opposite the operator

Height of handle on request

Clear passage width (LDBS) =

Rail 52 mm = Door width - 61

No. of fields -137

Rail 91 mm = Door width - 61

No. of fields -98

THTH

TH

Pas

sage

hei

ght

(DH

S)

LZ = Width between frame

LDBS

Hei

ght

of h

and

le

THTH

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail height 52

On request

Rail height 91

Threshold height = 181

Number of infills/fields per section

Number of ventilation grilles. Ventila-tion cross section 40 cm2 per grille

Threshold height = 306

Height RM DHS

n = No. of window sectionsn1 = No. of window sections in the wicket door

Height

21

Sectional Door ALS 40Door leaf of standard aluminium extrusions

Door leaf: Door sections of anodised aluminium extrusions in the standard version (NF). Overall thickness 42 mm. All door sections with finger-trap protection. All door section infills in 6 mm laminated safety glass. All infill heights are the same.

External view:

Size range: Within the limits shown below, any door width and height can be made in 10 mm increments (subject to the minimum ceiling height).

38,5

6012

0

76

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

400036253620

29302920

22302220

1875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

6

5

4

3

n

When using a shaft operator (installation example 5), the door lock is always on the side opposite the operator

TH =

UTH = TH + 84 ≤ 785OTH = TH + 35

Door height - 115

No. of window sections

THTH

TH

LZ = Width between frame

THTH

Field 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 WidthRail height 91

Number of infills/fields per section

n = number of window sections

Height3 (up to 3330 mm) 4 (up to 5500 mm)

22

Side Door NT 60

120

10

10

120

120

234

114

120

10

120

10

120

10

10 10 10

1050

80,5

120

120

234

80,5

1050

114

10 10

120

120

234

114

1050

80,5

10

185

120

120

234

1050

80,5

10

185

114

E

E

EE

EE

A A

AA

A A

AA

10

120

10

1050

10

151,

5

10

151,

5

120

10

1050

10

750

750

625

625

625

345

345

750

750

625

625

625

220

220

10

151,

5

10

750

750

625

625

625

282,

528

2,5

750

750

625

625

625

282,

528

2,5

10

151,

5

10

1050

1050

120

10

120

10

A

A

A

A A

A

10

1050

7310

170

500

375

500

500

500

500

500

500

375

500

500

500

500

500

500

375

500

500

500

500

500

10

151,

5

10 10 1010

151,

5

10

151,

5

750

750

625

625

625

1050

1050

1050

120

10

120

10

120

10

120

10

* see page 23, LF = Structural opening, RAM = Overall frame size, BH = Fascia panel height, BB = Fascia panel width LDB = Clear passage width, LDH = Clear passage height, TH = Door section height, LZ = Width between frame

LF

RAM: A = min. 1050 C = min. 855D = min. 1000 max.1280

RAM = min. 855max. 1280

LF LF

BH B

H

BH

RA

M =

199

0/21

15

RA

M =

N x

TH

+ 1

33,5

RA

M =

N x

TH

+ 1

33,5

LDH

= R

AM

- 7

3

LDH

= R

AM

- 7

3

LDH

= R

AM

- 7

3

LDB * LDB * LDB *

BB BB BB

LZ LZ LZ

LF LF LF

RAM = min. 855max. 1280

RAM: A = min. 1050 C = min. 855D = min. 1000 max.1280

LF

BH

RA

M =

N x

TH

+ 8

,5LD

H =

RA

M -

73

LDB *

BB

LZ

LF

RAM: A = min. 1050 C = min. 855D = min. 1000 max.1280

LFB

HR

AM

= N

x T

H +

133

,5LD

H =

RA

M -

73

LDB *

BB

LZ

LF

RAM: A = min. 1050 C = min. 855D = min. 1000 max.1280

LFB

HR

AM

= N

x T

H +

8,5

LDH

= R

AM

- 7

3

LDB *

BB

LZ

LF

RAM:min. 1150max. 280

LFB

HR

AM

= N

x T

H +

133

,5LD

H =

RA

M -

73

LDB *

BB

LZ

LF

RAM:min. 1150max. 280

LFB

HR

AM

= N

x T

H +

8,5

LDH

= R

AM

- 7

3

LDB *

BB

LZ

LF

RAM: min. 855max. 1280

LFB

HR

AM

= N

x T

H +

133

,5LD

H =

RA

M -

73

LDB *

BB

LZLF

RAM: min. 855max. 1280

LFB

HR

AM

= N

x T

H +

18,

5LD

H =

RA

M -

73

LDB *

BB

LZLF

RAM:min. 1150max.1280

LF

BH

RA

M =

N x

TH

+ 1

33,5

LDH

= R

AM

- 7

3

LDB *

BB

LZ

LF

RAM:max.280

LF

BH

RA

M =

N x

TH

+ 1

8,5

LDH

= R

AM

- 7

3

LDB *

BB

LZLF

TH -

155,

5TH

-23

4

TH=

750

THTH

THTH

+35

TH -

155,

5TH

-12

0

TH=

750

THTH

THTH

+35

TH -

155,

5TH

-23

4

THTH

THTH

TH+

35

TH -

155,

5TH

-12

0

THTH

THTH

TH+

35

Side Door NT 60ArrangementsFitting options

23

120 x 60160 x 60200 x 60

2010

2010

2010

Clear passage dimensions: Width = RAM – 146 * RAM – 200 (for arrangements 1, 2, 5)Height = RAM – 73

Standard sizes (infilled sections only, no glazing areas, no compound glazing) structural opening Ordering size Clear passage dim. * Overall frame size RAM 875 x 2000 855 x 1990 709 x 1917 875 x 2125 855 x 2115 709 x 2042 1000 x 2000 980 x 1990 834 x 1917 1000 x 2125 980 x 2115 834 x 2042

Special sizes: width: RAM 855 to 1280, height: RAM 1990 to 2525 (specify overall frame size)Doors with 3-point locking: RAM = min. 2025 mm

Arrangement 1Next to main door,opening outwardsRH hinged

Arrangement 2Next to main door,opening outwardsLH hinged

Arrangement 3Next to main door,opening inwards,LH hinged

Arrangement 4Next to main door,Opening inwards,RH hinged

Arrangement 5In the opening,opening outwards,RH hinged orLH hinged

Arrangement 6In the opening,Opening inwardsRH hinged orLH hinged

Arrangement 7Behind the opening,opening inwardsRH hingedor LH hinged

120 x 60160 x 60200 x 60

2010

2010

2010

Standard side dooronly STE 40, TPU 40, SPU 40 without glazing areas, without compound glazing

STE 40, TPU 40, SPU 40, APU 40with fascia panel

ALR 40, TAR 40with fascia panel

RAM RAM

LDB LDB

RAMLDB

LDB LDB

RAM RAM

RAMLDB

LF

LDB

RAM

INSIDE

INSIDE

INSIDE

INSIDE

INSIDE

INSIDE INSIDEINSIDE

Fasc

ia p

anel

hei

ght

= B

H

RA

M =

ord

erin

g si

ze =

LF

- 10

Str

uctu

ral o

pen

ing

= L

F

RA

M =

ord

erin

g si

ze

Str

uctu

ral o

pen

ing

= L

F

Str

uctu

ral o

pen

ing

= L

F

Fasc

ia p

anel

hei

ght

= B

HR

AM

= o

rder

ing

size

INSIDE

Aluminium angle 40 x 40

In the reveal

Behind thereveal

Side door NT 60in line withsectional door

Aluminium angle60 x 40

Post 160 x 60

steel angle82,5 x 35 x 3,75

INSIDE

INSIDE

INSIDE

Plug screw throughframe (on site)

INSIDE

Countersunk screwB6.3 x 70

max. 40

Post:

24

Track Application: NNormal tracks

210

685

550

200

H

• Door weights for roof loads STE 40 = 260 N/m2

TPU 40/SPU40/TAP 40/TAR 40 = 320 N/m2

APU 40 N/APU 40 B/ALR 40 N/ALR 40 B = 280 N/m2

ALS 40 = 560 N/m2

• Note minimum sideroom, see page 36

• LDB = Clear passage width• LDH = Clear passage height• RM = Ordering height• BW = Position of shaft support = = N 1 = RM + 310 = N 2 = RM + 335 = N 3 = RM + 415• ET = Min. distance back = • = N 1 + N 2 = RM + 440• = N 3 = RM + 700• = with shaft operator• N 1 + N 2 = RM + 650• = with shaft operator N 3 = RM + 700• DH = Rear track support = RM + 195• DM = Middle track support = see page 41• WE = Shaft centre from lintel• H = Min. headroom (see table)• DA = Distance to ceiling

N 1

N 2

N 3

ND 1

ND 2

ND 3

NH 1

NH 2

NH 3

NS 1

390

440

550

390

440

550

610-740

660-790

770-900

390

440

200

200

200

200

880

910

950

880

910

NS 2

L 1

L 2

LD 1

LD 2

H 4

H 5

H 8

HD 4

HD 5

950

880

910

1760

1760

HD 8

HS 4

HS 5

HU 4

HU 5

V 6

V 7

VU 6

VU 7

The clearance required for door movement must be free of obstructions, e.g. supply lines, heater fans etc.

Attention:Note the size range limitations for each door type as shown on pages 4-9 and 12-21!

For the version with a wicket door using manual operation, a hand chain hoist is recommended!

* for the version with a wicket door LDH ≈ RM - 100

H WE DA

N 1 390 140 280

N 2 440 160 330

N 3 550 180 440

N 3 760 with double spring assembly

ET

DH

DM

WE

DA

Cei

ling

heig

ht

BW

RM

= L

DH

*

Cle

aran

ce f

or d

oor

mov

e-m

ent

RM

- 2

00

RM

+ 1

10

RM

+ 1

58

RM

+ 3

20

INSIDE

FFL

LZ = Width between frame

Clearance for door movement

min. 125min. 125

INSIDE

Track size Headroom Track size Headroom Track size Headroom

RM + 500

RM + 540

RM + 280

RM + 280 Dimensions in mm

Minimum headroom clearance

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

Track Application: NDNormal tracks with inclinationup to max. 30°

25

H

45°

200

• Door weights for roof loads: STE 40 = 260 N/m2

TPU 40/SPU40/TAP 40/TAR 40 = 320 N/m2

APU 40 N/APU 40 B/ALR 40 N/ALR 40 B = 280 N/m2

ALS 40 = 560 N/m2

• Note min. sideroom, see page 36

• ET = min. distance back = RM + 450 – x 6,5 with shaft operator = RM + 700 – x 6,5• DH = Rear track support = RM + 195 – x 6,5• DM = Middle track support = see page 41• DA = distance to ceiling • For all other fitting dimensions, see normal tracks.

Only for determining the inclination of the roof in degrees (α)

% X (mm) % X (mm)

11 1,75 17,5 16 28,67 286,712 3,49 34,9 17 30,57 305,713 5,24 52,4 18 32,49 324,914 6,99 69,9 19 34,43 343,315 8,75 87,5 20 36,40 364,016 10,41 105,1 21 38,39 383,917 12,28 122,8 22 40,40 404,018 14,05 140,5 23 42,45 424,519 15,84 158,4 24 44,52 445,210 17,63 176,3 25 46,63 466,311 19,44 194,4 26 48,77 487,712 21,26 212,6 27 50,95 509,513 23,09 230,9 28 53,17 531,714 24,93 249,3 29 55,43 554,315 26,79 267,9 30 57,74 577,4

1000X

H F DA

ND 1 390 210 430

ND 2 440 210 450

ND 3 550 210 580

ND 3 760 with double spring assembly

The clearance required for door movement must be free of obstructions, e.g. supply lines, heater fans etc.

Attention:Note the size range limitations for each door type as shown on pages 4-9 and 12-21.

ET

Cei

ling

heig

ht

BW

RM

= L

DH

INSIDE

FFL

LZ = Width between frame

Clearance for door movement

min. 125min. 125

INSIDE

Cle

aran

ce f

or d

oor

mov

emen

t

DA

F

Track inclined up to 30°. To determine degrees,

see table.

Fiel

d 3

Fiel

d 2

Fiel

d 1

Ord

erin

g he

ight

from 2000 Width

On request

max. 30°

max. 16°

DH

DM

DM

26

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

Track Application: NHNormal trackswith minimum high-lift

300

685

550

250

• Door weights for roof loads STE 40 = 260 N/m2

TPU 40/SPU40/TAP 40/TAR 40 = 320 N/m2

APU 40 N/APU 40 B/ALR 40 N/ALR 40 B = 280 N/m2

ALS 40 = 560 N/m2

• Note minimum sideroom, see page 36

• LDB = Clear passage width• LDH = Clear passage height• RM = Ordering height• BW = Position of shaft support = = NH 1 = LH + 200 = NH 2 = LH + 225 = NH 3 = LH + 305• LH min. = RM + 330 LH max. = RM + 460

• DH = Rear track support = 2 x RM – LH + 645• DM = Middle track support = see page 41• WE = Shaft centre from lintel• H = Min. headroom• DA = Distance to ceiling

WE DA

NH 1 140 280

NH 2 160 330

NH 3 180 440

NH

1 +

2N

H 3

ET = min. distance back

2x RM - LH + 1120

2x RM - LH + 650

2x RM - LH + 880

2x RM - LH + 950

The clearance required for door movement must be free of obstructions, e.g. supply lines, heater fans etc.

Attention:Note the size range limitations for each door type as shown on pages 4-9 and 12-21.

Cei

ling

heig

ht

BW

RM

= L

DH

INSIDE

FFL

LZ = Width between frame

Clearance for door movement

min. 125min. 125

INSIDE

Cle

aran

ce f

or d

oor

mov

emen

t

LH-3

10

Trac

k he

ight

= L

H

ET

DH

DM

WE

DA

Ord

erin

g he

ight

from 2000 Width

On request

Dimensions in mm

DM

Manual operation with long spring buffer (standard)

Manual operation with short spring buffer (special)

Shaft operator with long spring buffer

Manual operation and shaft operator with long spring buffer (standard)

Track Application: NSNormal tracks with double radius2 x 45 °

27

200

• Door weights for roof loads: STE 40 = 260 N/m2

TPU 40/SPU40/TAP 40/TAR 40 = 320 N/m2

APU 40 N/APU 40 B/ALR 40 N/ALR 40 B = 280 N/m2

ALS 40 = 560 N/m2

• Note minimum sideroom, see page 36

• H = Minimum headroom, see page 24• ET = Minimum distance back on request• DH = Middle track support, on request• DM = Rear track support, on request• DA = Distance to ceiling min. 250

700068756750662565006375625061256000587557505625550053755250512550004875475046254500437542504125400038753750362535003375325031253000287527502625250023752250212520001875

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

H B WE BW NS 1 > 390 300 140 RM + 310 NS 2 > 440 350 160 RM + 335

The clearance required for door movement must be free of obstructions, e.g. supply lines, heater fans etc.

Attention:Note the size range limitations for each door type as shown on pages 4-9 and 12-21.

Door height Track height RM LH min. LH max. 5000 5190 5810 4875 5065 5685 4750 4940 5560 4625 4815 5435 4500 4690 5310 4375 4565 5175 4250 4440 5030 4125 4315 4885 4000 4190 4730 3875 4065 4585 3750 3940 4440 3625 3815 4295 3500 3690 4150 3375 3565 4005 3250 3440 3860 3125 3315 3715 3000 3190 3570 2875 3065 3425 2750 2940 3280 2625 2815 3135 2500 2690 2990 2375 2565 2845 2250 2440 2700 2125 2315 2555 2000 2190 2410 1875 2065 2265

NS

1N

S 2

Ob

stru

ctio

n he

ight

BW

RM

= L

DH

INSIDE

FFL

LZ = Width between frame

Clearance for door movement

min. 125min. 125

INSIDE

Cle

aran

ce f

or d

oor

mov

emen

t

RM

- 2

00ET

DH

DM

WE

Trac

k su

pp

ort

heig

ht =

LH

DA

B

Cei

ling

heig

ht =

LH

+ m

in.

250

Ord

erin

g he

ight

from 2000 Width

On request

Dimensions in mm

LH - RM + 387

DM

28

Track Application: HHigh-lift tracks

750

550

250

300

Table 2Demarcation of track height for track application H

Attention:Note the size range limitations of the door types as shown on pages 4-9 and 12-21!

770075757450732572007075695068256700657564506325618559355685543551854935468544354185

2250

2500

2750

3000

3250

3500

3750

4000

4250

4500

4750

5000

5250

5500

5750

6000

6250

6500

6750

7000

7250

7500

7750

8000

• LDB = Clear passage width• LDH = Clear passage height• RM = Ordering height• LH = Track height (see tables 1 + 2)• BW = Position of shaft support = H 4 + 5 = LH + 280, H 8 = LH + 305

• DH = Rear track support = 2 x RM – LH + 645• DM = Middle track support = see page 41• WE = Shaft centre from lintel (see table 1)• H = Min. headroom, see page 24• DA min = H 4 = 420 DA min = H 5 = 450, 625 with double spring assembly

H 8 = 490, 650 with double spring assembly• Other versions on request• Note min. sideroom, see page 36

H 4

+ 5

H 8

ET = min. distance back

2x RM - LH + 1120

2x RM - LH + 650

2x RM - LH + 880

2x RM - LH + 650

2x RM - LH + 950

Note1. Choose the required track

height according to the

door height in table 1

2. For the intersection of

door width and track height

see table 2

3. Check the specifications

below for availability.

The clearance required for door movement must be free of obstructions, e.g. supply lines, heater fans etc.

Explanation of shaded areas

All door types available in any version. All door types available, compound windows and/or wicket door on request.

Door types STE 40, TPU 40, APU 40 N/-B and ALR 40 N/-B available, door types SPU 40, TAP 40 and TAR 40 as well as versions with compound windows and/or wicket door on request.

Door type STE 40 available, other door types in any version on request. All door types in any version on request.

Door height RM LH min. LH max. 7000 7460 9700 6875 7335 9575 6750 7210 9450 6625 7085 9325 6500 6960 9200 6375 6835 9075 6250 6710 8950 6125 6585 8825 6000 6460 8700 5875 6335 8575 5750 6210 8450 5625 6085 8325 5500 5960 8200 5375 5835 8075 5250 5710 7950 5125 5585 7825 5000 5460 7700 4875 5335 7575 4750 5210 7450 4625 5085