Upload
marcu-traian
View
220
Download
0
Embed Size (px)
Citation preview
8/13/2019 User's Guide for Iptime Ve
1/54
Users Guide
www.zioncom.ne
t
-0-
8/13/2019 User's Guide for Iptime Ve
2/54
Users Guide
www.zioncom.ne
Preface
This document is users manual for IP Router IPTIME VE.This manual consists of IP Router components, installation guide, settings, and
information on how to use IP Router and its functions.
It is recommended that you have a clear understanding of this manual before you
start using the IP Router.
Before you start
First, read Chapter 4, Installation section for installation information before
you install the IP Router.
Second, read Chapter 6. IP Router Setup section to setup the IP Router to
best fit your Internet environment.
t-1-
8/13/2019 User's Guide for Iptime Ve
3/54
Users Guide
www.zioncom.ne
TABLE OF CONTENTS1.WARNING3
2.PACKAGE CONTENTS43.SPECIFICATION5
4.INSTALLATION.9
4.1 Before Installation ...9
4.2 Installation 9
4.3 Network Sketch Map 11
5.LOCAL COMPUTER SETUP..13
5.1 Windows 95/98/ME Setup 145.2 Windows 2000 Setup 19
5.3 Windows XP Setup 23
6.ROUTER SETUP28
6.1 Start Internet Explorer to Login 28
6.2 PPPoE User Setup 29
6.3 Dynamic IP User (Cable Modem...) Setup 34
6.4 Static IP User Setup .. .....38
6.5 Status 41
6.5.1 WAN Status 41
6.5.2 LAN Status 42
6.6 Basic Setup 43
6.6.1 LAN/DHCP Setup 43
6.6.2 Link/Info .46
6.6.3 Routing Table 47
6.7 System 48
6.7.1 Password . ......48
6.7.2 Default/Restart ..49
6.7.3 Firmware Upgrade 50
6.7.4 System Time 52
Appendix A. UTP Cable specif ication53
t-2-
8/13/2019 User's Guide for Iptime Ve
4/54
Users Guide
www.zioncom.ne
1.WARNING
1. Use only the power adapter provided with the IP Router for power
connection. Using other power adapter may cause an error or damage to the
IP Router.
2. Do not drop or give a physical shock to the IP Router. It may affect internalcircuit.
3. Do not disassemble the IP Router without sufficient understanding of your
action.
4. Avoid direct exposure to the sun.
5. Do not leave the IP Router near moist or fire.
t-3-
8/13/2019 User's Guide for Iptime Ve
5/54
Users Guide
www.zioncom.ne
2.PACKAGE CONTENTS
Package contents of IP Router IPTIME VE are as follows;
2.2 IPTIME VE Router
2.3 Switch DC Power Adapter (5V, 1A)
2.4 Ethernet Cable
2.5 Users guide
t-4-
8/13/2019 User's Guide for Iptime Ve
6/54
Users Guide
www.zioncom.ne
3. SPECIFICATION
This IP Router is a highly integrated IP Router with many functions such as
Gateway, Switch, DHCP Server, Firewall etc
Network Address Transform (NAT) With providing Internet application
this IP Router can allow more than one user to connect with Internet at the
same time by sharing one public IP address; It supports many connectionways xDSL Cable Modem LAN/ Leased Line and so on.4 Ports 10/100M Switch It has 4 Network 10/100M switch ports port
support MDI/MDIX automatic identification function, Switch port can
connect to other switches, so that can support over hundred computers to
go to Internet at the same time.
Support VPN Pass-through Supports VPN Pass-through PPTP
dialogue and also supports users to configure VPN Server and Client in
LAN.
PPPoE(ADSL) Automatic Disconnection/Connection Users can
optionally choose automatic disconnection in idle time and connection in
access time to save Internet access cost.
Firewall Users can randomly refuse or allow data from Internet Support
DDOS protection and Ping forbiddance that can protect users from
Internet un-safety and virus such as shock wave.
DHCP Server All computers, which connect to Internet can get TCP/IP
configuration information from IP Router automatically, so that it can make
sure easy user management.
Static IP Address assign MAC address and IP address band and assign
function can make sure most user management administration in LAN.
Management Based on Web Page Both network configuration and
t-5-
8/13/2019 User's Guide for Iptime Ve
7/54
Users Guide
www.zioncom.ne
system configuration are based on inside Web Server. The user interface
is clear and usage is easy. By this interface users can also update
software to enhance the system stability and expansibility.Internet Access Control Different administration can be setup for
different users.
Data Package Filtrate Port filtration, IP address filtration, MAC address
filtration, Keywords filtration allow users flexibly setup IP Router and judge
data has been refused/has accessed or not.
Virtual Server Allow other users from Internet access WWW, FTP server
or other servers in LAN.Connection Time Control Setup special connection time to flexibly
control the time for LAN accessing Internet.
DMZ Server Allow one computer to be totally open to Internet to make
sure special application.
Remote Management Users can totally manage office or home network
wherever they are.
DDNS By this function users can setup their own web station.
Remote Wake-up Computers in LAN can be woken up by remote control.
Detailed Specification
ITEM IPTIME VE
StandardIEEE 802.3, IEEE 802.3u, IEEE 802.x, IEEE Fast
Ethernet,
ProtocolTCP/IP, NAT, DHCP, UDP, FTP, PPPoE, PPTP, L2TP,
HTTP, DNS, IPSec/VPN Pass-through
WANOne 10/100Mbps RJ-45 port, automatic
sense cross cable
T e c h ni c
al p
ar am
e t er
External
PortLAN
Four 10/100Mbps speed Ethernet switch
port, auto sense cross cable
t-6-
8/13/2019 User's Guide for Iptime Ve
8/54
Users Guide
www.zioncom.ne
Cable 100Base-T UTP/STP 5 or above standard
Control
interface Based on Web application
Inside
function
10/100Mbps swi tch
LAN/WAN port auto sense cross cable
WAN port static/dynamic IP flexible setting up
PPPoE dial-up and connection time setting up
PPPoE dial-up and automatic/manual connection
Support VPN Pass-through
DHCP Service
DNS relaying
DMZ Server
Static IP address assign
Connection setting up and stat.
Connection time limit
FirewallPort/IP/MAC/Keyword filtration
Remote control
Remote wake up
DDNS
Gateway
Virtual Server
Data forward
NAT NAPT and PAT
CPU ARM9 166MHz
FLASH 2MB Flash
P r o
d u c t
s p c i f i c
a t i
on
Memory 8MB SDRAM
t-7-
8/13/2019 User's Guide for Iptime Ve
9/54
8/13/2019 User's Guide for Iptime Ve
10/54
Users Guide
www.zioncom.ne
be informed. The users please take care of it by themselves.
4. INSTALLATION
4.1 BEFORE INSTALLATION 4.1.1. Firstly please confirm your computer OS (Windows 95,98,NT,ME,2000,
XP, Linux, Mac) and Web browser (Internet Explorer 4.0 with JavaScript function
Netscape Navigator 4.0 or above version) 4.1.2. Make sure there is LAN Card, which has been correctly installed in your
computer.
4.1.3. If you are xDSL user, please remember your user ID and password.
4.1.4. If you connect Internet by LAN or WAN , please get the following
information from your network administrator: IP address is static or dynamic, DNS,
default gateway, account and so on.
If your computer has installed ADSL PPPoE dial-up software before the
installation of IP Router, please backup your installation software and uninstall your
ADSL PPPoE dial-up software by Start->control panel->Add or Remove Programs.
4.2 INSTALLATION4.2.1. Setup WAN connection: connect broadband cable (xDSL, Cable Modem
or LAN/ Leased cable) with WAN port of IP Router.
4.2.2. Setup LAN connection: connect your computer LAN cards port or your
switch UPLINK port with one LAN port of IP Router by a common network cable.
Note: All L AN ports o f IP Router can automatically sense cross cable, so
you can either use through cable or cross cable to connect LAN card or
switch.
4.2.3. Turn on the power: connect and the power supply, turn on it. Then IP
Router comes to self-detect state. During the self-detect: PWR LED will be long
t-9-
8/13/2019 User's Guide for Iptime Ve
11/54
Users Guide
www.zioncom.ne
light, RUN LED will slow flash after correct startup, other four LAN LED and WAN
LED will flash only twice rapidly, then the system will come to normal work state.
4.2.4. Start computerLED explanation
RUN System status LED, slow flash after correct startup.
POWER Power LED, long light
WAN WAN port connection LED, flashing refers to data transformation
LANLAN port connection LED (1,2,3,4), flashing refers to data
transformation
POWER (red): power
connection state
RUN: system running
state
WAN (green): WAN
LAN (green): LAN port
Port explanation
WAN port Connect xDSL/Cable Modem or Special cable
LAN port Connect personal computer or hub, switch and so on
Power jack Connect power adapter (5V/1A)
ResetPress Reset button. Switch the power off/on. After
switching the power on, about 5 seconds later RUN
t-10-
8/13/2019 User's Guide for Iptime Ve
12/54
8/13/2019 User's Guide for Iptime Ve
13/54
Users Guide
www.zioncom.ne
4.3 NETWORK SKETCH MAP
DC Adapter: 5V/1A
3. connects with
power adapterModem PC
2. connects with PC1. connects with
xDsl Modem
EXAMPLE 1.
Internet
Cable/xDSL
Modem
ipTime VE Router
Server
t-12-
8/13/2019 User's Guide for Iptime Ve
14/54
Users Guide
www.zioncom.ne
EXAMPLE 2.
ipTime VE Router
Switch
nternetCable/xDSL
Modem
Server
Server
Note During the usage, the sequence of turn on is firstly turn on Modems
power supply 1 minute after Modem startup tu rn on IP Router power supply ,
then turn on th e compu ter .
5. LOCAL COMPUTER SETUP
Users should configure local network to access Internet by IP Router.
Users should know the default configuration of IP Router before installation.
Users must connect with IP Router again after configure computers local
network. Please make sure your computer setting is as follows, Otherwise IP
Router cannot be correctly connected (Linux and Mac users please setup as
t-13-
8/13/2019 User's Guide for Iptime Ve
15/54
Users Guide
www.zioncom.ne
follows by relative conference).
The default configuration of IP Router is:
IP address 192.168.0.1 Subnet Masks 255.255.255.0
Users can setup static or dynamic IP configuration.
5.1 Windows 95/98/ME SETUP
(1) Install IP Router.
(2) Start computer with Windows-95/98/ME, and check the LAN LED is onor off. If off, please confirm the connection between your computer and
IP Router.
(3) Click Start ->Setting -> Control panel .
(4) In Control panel double click Network .
t-14-
8/13/2019 User's Guide for Iptime Ve
16/54
Users Guide
www.zioncom.ne
(5) Click TCP/IP and Properties .
t-15-
8/13/2019 User's Guide for Iptime Ve
17/54
Users Guide
www.zioncom.ne
(6) Click IP address option and choose Obtain an IP address
automatically .
(7) Click Gateway menu and make sure Installed gateways is blank.
(8) Click the DNS Configuration and select Disable DNS , then Click
OK.
(9) During the TCP/IP installation process there will ask you to insert
Window installation CD. After inserting it then click OK.
(10) After TCP/IP configuration has completed, the window of System
Setting Chang will pop-up, select Yes , then restart computer.
t-16-
8/13/2019 User's Guide for Iptime Ve
18/54
Users Guide
www.zioncom.ne
(11) After restart, click start -> run .
(12) Input command then click OK
(13) Input ipconfig in pop-up command window, then Enter .
(14) Please make sure your IP is the same with below. If same then your
configuration is successful, or please redo the above step and restart
your computer.The IP address is between 192.168.0.2 and192.168.0.254 The subnet mask is 255.255.255.0 The default gateway is 192.168.0.1
t-17-
8/13/2019 User's Guide for Iptime Ve
19/54
Users Guide
www.zioncom.ne
(15) Input ping 192.168.0.1 then Enter .
t-18-
(16) If you can see Reply from 192.168.0.1: bytes=32 time=2ms TTL=64 the
connection between your computer and IP Router is completed.
8/13/2019 User's Guide for Iptime Ve
20/54
Users Guide
www.zioncom.ne
5.2 Windows 2000 SETUP(1) Install IP Router.
(2) Start Windows 2000 and check LAN LED is on or off. If off, pleaseconfirm the connection of your computer with IP Router.
(3) Click start ->Setting -> Panel Control .
(4) Double click the Netwo rk and Dial-up Connection in control
panel .
t-19-
8/13/2019 User's Guide for Iptime Ve
21/54
Users Guide
www.zioncom.ne
(5) Click Local area connection -> Properties -> Internet protocol
TCP/IP and Properties .
(6) Click General bar, Select Obtain an IP address automatically and Obtain DNS server address automatically
(7) Click OK.
t-20-
8/13/2019 User's Guide for Iptime Ve
22/54
8/13/2019 User's Guide for Iptime Ve
23/54
8/13/2019 User's Guide for Iptime Ve
24/54
Users Guide
www.zioncom.ne
5.3 Windows XP SETUP(1) Install IP Router.
(2) Start Windows XP and check LAN LED is on or off. If off, please confirmthe connection of your computer with IP Router.
(3) Click Start ->Setting -> Panel Control
(4) Double click the Netwo rk and Internet Connections in control
panel .
(5) Click Network connection -> local area
connection -> properties -> Internet protocol TCP/IP and
Properties .(6) Click General ,Select Obtain an IP address automatically and
Obtain DNS server address automatically
(7) Click OK
t-23-
8/13/2019 User's Guide for Iptime Ve
25/54
Users Guide
www.zioncom.ne
t-24-
8/13/2019 User's Guide for Iptime Ve
26/54
8/13/2019 User's Guide for Iptime Ve
27/54
Users Guide
www.zioncom.ne
(8) Click Start ->Run
(9) Input cmd , Click OK
(10) Input ipconfig in the pop-up command window.
(11) Please make sure your IP is the same with below. If same then your
configuration is successful, or please redo the above steps and restart
your computer.The IP address is between 192.168.0.2 and192.168.0.254
The subnet mask is 255.255.255.0 The default gateway is 192.168.0.1
t-26-
8/13/2019 User's Guide for Iptime Ve
28/54
Users Guide
www.zioncom.ne
(12) Input ping 192.168.0.1 , then Enter . (13) If you can see Reply from 192.168.0.1: bytes=32 time=2ms TTL=64 then
the connection between your computer and IP router is completed.
t-27-
8/13/2019 User's Guide for Iptime Ve
29/54
8/13/2019 User's Guide for Iptime Ve
30/54
8/13/2019 User's Guide for Iptime Ve
31/54
Users Guide
www.zioncom.ne
Select PPPoE User (ADSL) radio button.
Key in the User ID and Password provided by your Internet serviceprovider.Click the Apply button.You may see the popup window.
In case Conn. Status is Successfully connected , the configuration is
correct.Click Show Internet connection status and see the 6.5.1.
t-30-
8/13/2019 User's Guide for Iptime Ve
32/54
Users Guide
www.zioncom.ne
If In case Conn. Status is Invalid ID/password , the configuration is
incorrect.
t-31-
Click the close button and check your ID& password.
If Conn. Status keeps unchanged, check whether your service type iscorrect.Confirm the WAN connection status: If WAN connection is successfullyestablished, then by clicking Show Internet Information you can enterWAN status web page; or click Status -> WAN status , as thefollowing.
Connection Type should be PPPoE (ADSL)
Connection Status should be successfully connected Physical Address is shows Router WAN port MAC Address.WAN IP Address , Subnet mask , Default Gateway , Primary DNSserver and Secondary DNS server can be different from thefollowing values. (These addresses are provided by your ISP)
8/13/2019 User's Guide for Iptime Ve
33/54
Users Guide
www.zioncom.ne
Disconnect is manual disconnection button. If you click then
the system will disconnect with Internet
Connect is manual connection button. By clicking it the
system can be connected to Internet again.
Click Save to save current configuration.
t-32-
8/13/2019 User's Guide for Iptime Ve
34/54
Users Guide
www.zioncom.ne
Restart all PCs connect with IP Router.
Notes: Please save IP Router Configuration after completion, otherwise
configuration will lose when power off or restart.
Other Configuration:
MTU: Input MTU value of data package, default value is 1454. Normally
please do not change it.
Disconnect PPP session if idle time is longer than Min : If you
choose this option and setup the time T, then the IP router
automatically disconnects from Internet after T idle time.
Connect On Demand: IP Router can automatically connect with
Internet if there is Internet access after disconnection. Note: during
usage if there is disconnection due to external causes, then the IP
Router will try to connect with Internet at once until successful
connection. This function is the IP Router inner function and does
t-33-
8/13/2019 User's Guide for Iptime Ve
35/54
Users Guide
www.zioncom.ne
nothing with Connect On Demand function. Connect On Demand is
only effective to Disconnect PPP session if idle time is longer than
Min .Connect Manually: By this option users have to connect with Internet
manually after disconnection. This option is only effective to Disconnect
PPP session if idle time is longer than Min .
Prevent reconnection although no response from PPP server: This
option is to shut off IP Router inner automatic connection function. By
choosing this option if external network disconnects, IP Router will not
try to connect at once.
6.3 DYNAMIC IP USER (Cable/Modem) SETUP
By this connection way IP Router can get IP address automatically from ISP
(such as: CHINA TELCOM). It is suitable for connection ways such as Cable
Modem, LAN and so on.
Turn on the external Cable Modem and check the WAN LED of IP
Router.
If WAN LED is off, please re-confirm the network cable between
external Modem and WAN port.
Click Basic Setup -> WAN Setup as diagram:
Choose Dynamic IP user (Cable Modem)
Click Apply to complete.
t-34-
8/13/2019 User's Guide for Iptime Ve
36/54
Users Guide
www.zioncom.ne
You will see the following pop-up window
If Conn. status is Successful connected , the configuration is correct.Click Show Internet Information and see the 6.5.1
If connection status keeps to be Connecting to Internet , please do the
following steps:
Close the pop-up window.
t-35-
8/13/2019 User's Guide for Iptime Ve
37/54
8/13/2019 User's Guide for Iptime Ve
38/54
Users Guide
www.zioncom.ne
Connect button is manual WAN port IP address refresh functionbutton. If click it WAN port will re-get dynamic IP address andconnect with Internet.
Click Save button to save current configuration, then restart all PCs
connected with IP Router
Note:
After completed setup , please save IP Router configuration , otherwise
t-37-
8/13/2019 User's Guide for Iptime Ve
39/54
8/13/2019 User's Guide for Iptime Ve
40/54
Users Guide
www.zioncom.ne
Input WAN IP address , Subnet mask , Default Gateway , Primary DNS
Server and Secondary DNS Server provided by ISP.
Click Apply to complete.You will see the following pop-up window:
Check WAN connection status: If it is Configuration is done , click
Show Internet Information to enter WAN status page; or click
Status ->WAN status , as following diagram:
t-39-
8/13/2019 User's Guide for Iptime Ve
41/54
8/13/2019 User's Guide for Iptime Ve
42/54
Users Guide
www.zioncom.ne
6.5 STATUS6.5.1 WAN Status
Click Status -> WAN Status as following:
This page shows current Internet connection status (WAN port), including
Connection Type , Connection Status , WAN IP address, Subnet mask , Default
Gateway and DNS server . If it is dynamic IP way, Disconnect button or
Connect button will be shown above. Click Disconnect button to release
current WAN Port IP Address, then click Connect button to refresh WAN IP
address; If it is PPPoE way, then Connect or Disconnect button will be shown
above. Click Connect button to connect with Internet, click Disconnect button
to disconnect with Internet.
Refresh Refresh current web page. All of the following web pages will
have this button with the same function.
Save Save IP Router current configuration. All of the following web pages
will have this button with the same function.
t-41-
8/13/2019 User's Guide for Iptime Ve
43/54
Users Guide
www.zioncom.ne
6.5.2 LAN StatusClick Status > LAN Status as following:
LAN Information: Display LAN port Physical Address, current LAN
connection status (LAN port) and DHCP server Status, including the IP
address range and quantity to LAN IP address and subnet mask, DHCP
Server.
Allocated IP Informat ion: display the IP address information, which has
been rented by DHCP Server.
Number The location in list
IP address IP address which has been allocated to clients by
DHCP server.
Physical address MAC address of client computer.
t-42-
8/13/2019 User's Guide for Iptime Ve
44/54
Users Guide
www.zioncom.ne
6.6 BASIC SETUP
6.6.1 LAN/DHCP SetupClick Basic Setup -> LAN/DHCP SETUP as following:
t-43-
8/13/2019 User's Guide for Iptime Ve
45/54
Users Guide
www.zioncom.ne
LAN port basic parameter and DHCP server parameter can be setup in this
web page.System IP Setup If you want to change IP Router LAN port address, you
can setup as follows:
System IP address IP address in LAN. This IP address is factory
default value 192.168.0.1 , and you can change it.
Subnet Mask Subnet mask in LAN. This value cannot be changed.
TCP/IP protocol configuration includes IP address, subnet mask,
Gateway and DNS server and so on. It is not easy to configure TCP/IP
protocol correctly in all computers in LAN, but it is lucky that DHCP Server
has provided this function. If you choose the DHCP function, you can let
DHCP Server configure TCP/IP protocol in all computers in LAN
automatically.
DHCP Setup : If you want to able or disable DHCP Server, change DHCP
address range, you can choose the following options:
DHCP Server Status Display DHCP Server current status.
DHCP Server Operation Able and disable DHCP Server. The default
value is able DHCP Server.
DHCP IP Pool IP address range automatically allocated by DHCP
Server is address pool.
Manual DNS configuration: Let DHCP Server automatically allocated
the DNS Server to Client PC.
t-44-
8/13/2019 User's Guide for Iptime Ve
46/54
8/13/2019 User's Guide for Iptime Ve
47/54
Users Guide
www.zioncom.ne
6.6.2 Link Setup/InfoClick Basic setup -> Link Setup/Info as follows:
All IP Router ports speed, Link information and port statistics data and so on
can be setup by this web page:
Link Setup Setup every ports connection speed.
t-46-
8/13/2019 User's Guide for Iptime Ve
48/54
8/13/2019 User's Guide for Iptime Ve
49/54
8/13/2019 User's Guide for Iptime Ve
50/54
Users Guide
www.zioncom.ne
6.7.2 Default/RestartClick System -> Default/Restart as follows:
Click Factory default button to restore all configuration of IP Router to
factory default values.
Default username root
Default password none
Default IP address 192.168.0.1
Default subnet mask 255.255.255.0
After restore to factory default values, IP Router will restart automatically.
Click Restart System button, IP Router will restart.
t-49-
8/13/2019 User's Guide for Iptime Ve
51/54
Users Guide
www.zioncom.ne
t-50-
6.7.3 Firmware UpgradeClick System -> Firmware Upgrade as follows
By updating the IP Router software, you can get new functions or
performance.
Software update steps:
1) Login our company homepage www.zioncom.net , download new
version software to your local hard disk.
* Please notice production and software type.
http://www.zioncom.net/http://www.zioncom.net/8/13/2019 User's Guide for Iptime Ve
52/54
Users Guide
www.zioncom.ne
2) Click Browse button to choose you downloaded file.
3) Click Upgrade button to upgrade system software.
t-51-
8/13/2019 User's Guide for Iptime Ve
53/54
Users Guide
www.zioncom.ne
4) After update, IP Router will restart automatically.
5) Please check you firmware version.
Note:
Update phase is about 30 seconds. During the update progress
please do not turn the power off otherwise the IP Router wi ll be damaged.
6.7.4 System TimeClick System -> System Time as follows
Set the time here by entering it manually or use NTP (Network Time Protocol.)
NTP is standard protocol on the Internet that synchronizes the time settings
accurately for all the computers on your network.
Current System Time: Current time of router.
Time Server: Select a Time Server for synchronize the time.
t-52-
8/13/2019 User's Guide for Iptime Ve
54/54
Users Guide Standard Time Zone: Select your time zone from the pull-down menu.
If use that Scheduler in the advanced function can work well. Please setup
correct system time. After choose correct time zone click Apply to update thecurrent time of IP Router; If can not update correctly, please choose other time
server till success.
Appendix A UTP Cable specification
Twisted pair Category-5 straight-through cableTwisted pair Category-5 Cross over cable