1. AptX Low Latency

Avantree Clipper Pro is a Bluetooth audio receiver incorporating the latest “aptX low latency” technology, for CD-like quality sound and with virtually no audio delay. Ideal for games, watching TV and movies without lip sync delay.

To take advantage of the better performance offered by APTX low latency codec, the other device must also support the same codec (Such as Avantree’sSaturn Pro, Priva II, Leaf, etc). If the transmitter only supports the normal AptX codec, or the SBC one, these codecs will be used instead.

2. Product overview & basic operationBasic operation

3. What’s in the box?

A. Avantree Clipper ProB. Avantree 3.5mm audio splitter *1C. 3.5mm audio cable *1D. Micro USB charging cable *1E. User manual & Quick user guide

4. Pairing and connecting

4.1. Connecting to a mobile phone/tabletStep 1. Ensure Clipper Pro is off.Step 2. Set Clipper Pro to PAIRING MODE - Press and hold MFB for 7 seconds until the LED flashes BLUE and RED alternately and you hear “pairing”.Step 3. Activate Bluetooth on your phone/tablet and select “ Avantree Clipper Pro” , LED flash once per 5 seconds once connected, and you hear “connected”.

Reconnect: Whenever you turn Clipper Pro on again, it will automatically reconnect to your phone.

4.2. Connecting to a Bluetooth transmitter

Step 1. Ensure Clipper Pro is off.Step 2. Set Clipper Pro to PAIRING MODE - Press and hold MFB for 7 seconds until the LED flashes BLUE and RED alternately and you hear “pairing”.Step 3. Set your Bluetooth transmitter to PAIRING MODE**.Step 4. Keep both devices close and wait for 5-30 seconds. Once connected, LEDs on both devices will slow down and you hear “connected”.

Step 4. Connect Clipper Pro to the second Bluetooth device as above.Step 5. Once connected, restart Clipper Pro and the first paired device. It will then automatically reconnect to the two devices simultaneously.Note: Once disconnected over 10 minutes, Clipper Pro will automatically power itself off.

5. How to reset to factory default setting?

Step 1. Turn on the Clipper ProStep 2. Press and hold the V+ and V- button for 7 secondsStep 3. The Blue and Red LED will flashes twice then power off at the same time

**PARING MODE: Discoverable mode for Bluetooth device, normally the LED blinks quickly or flashes between two colors alternately.

4.3. Connecting to two Bluetooth devices simultaneously

Step 1. Connect the first Bluetooth device as above. Then turn off Clipper Pro.Step 2. Turn off the bluetooth on the first paired device. (If it is a transmitter, turn it off)Step 3. Set Clipper Pro to PAIRING MODE again – Press and hold MFB for 6 seconds until the LED flashes BLUE and RED alternately.

6. LED indications

3.5 mm Audio jack

LED indicatorMulti-function button (MFB)

Micro USB port

Microphone

Volume up (Next track)Volume down (Previous track)

Dispose of the packaging andthis product in accordance withthe latest provisions.

Dispose of the packaging andthis product in accordance withthe latest provisions.

Charge from USB charger Charge from PC

www.avantree.comZ-PKMN-AS7L-V5

For a Better Experience

Audio delay by transmitter type -Transmitter support - The audio delay will beaptX Low Latency codec Around 40msaptX codec Around 180msSBC codec (most standard Bluetooth audio) Around 250ms

7. Charging

When the LED flashes RED, you should recharge the device. Please remove the micro-USB protector and charge it. It normally takes around 2 hours to fully charge the battery. The LED will stay RED when charging and will turn off when charging is complete.Charging RequirementYou can connect Clipper Pro via the supplied micro USB cable to your own USB chargers (wall charger/travel charger/car charger, etc.) with 5V/500mA-1A or PC USB port. It’s ok to use most mobile phone chargers on the market.

8. Product Specifications

• BT version: 4.2• BT profile: A2DP, AVRCP, HFP, HSP• Audio codec: aptX Low Latency, aptX, SBC• Operational range: Class II, up to 10 meters• Working time: Up to 6 hours• Standby time: 100 hours• Charging time: 2 hours• Product weight: approx. 15g• Product size: 50.5*26*18mm

Note: The talk and standby times may vary when used with different mobile phones or other devices and also defendent upon different usage styles, settings and operating environment.

9. Declaration of ConformityThis device complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.

FCC ID: BTHS-AS7

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Power on LED flashes BLUE for 2 seconds

Power off LED flashes RED for 2 seconds

Pairing mode

Connected LED flashes BLUE once every 10 seconds

Disconnected

Low battery

Charging LED stays RED

Fully charged

Restore to default setting LED flashes BLUE and RED together twice (appears PINK)

LED flashes BLUE and RED alternately

LED flashes BLUE twice every 10 seconds

Red LED turns off

LED flashes RED once every 30 seconds

Note: Some functions may not work when used with different mobile phones or other Bluetooth devices.

Button

MFB

V+

V–

Function OperationPower on/off Hold MFB for 2-3 seconds to turn Clipper Pro ON/OFF,

you will hear “ Welcome to Avantree” / “ Goodbye”Enter pairing mode From off mode, press & hold for 7 seconds until LED

flashes BLUE and RED fast, you will hear “pairing”. Answer/End a call Press MFB once when a call is incoming or in progressReject a call Press & hold MFB for 2 seconds when a call is incomingLast number redial Double click MFBPlay/Pause Press once MFB when streaming music

Press V+ onceNext track Press and holdVolume up

Volume downPrevious track

Press V- oncePress and hold

Press and hold V+ and V- together for 7 seconds, the LED flashes BLUE and RED together ( appears PINK)

V+& V- Restore to default settings

ConnectPair

Once connected, the LEDs on both devices will slow down.

Use your existing headphonesto listen to the TV wirelessly

Enjoy3

Set Clipper pro to pairingmode

Set transmitter to PAIRING MODE*

Keep them close & wait

Hold MFB 6S, LED flashes BLUE and RED alternately

BluetoothSettings

BluetoothDevices

Avantree Clipper Pro

ConnectPair

From off, hold for 6s, LEDflashes BLUE and RED alternately

Activate Bluetooth, search and select “Clipper Pro” to connect.

Hold MFB 6S

Enjoy3

Stream music wirelessly

A. B. C. D.

E.

Dual Link

- 6 -- 4 -

- 9 - - 10 - - 11 -

- 2 -- 1 -

- 5 - - 7 - - 8 -

- 3 -

Contents1. AptX Low Latency

2. Product overview & basic operation

3. What’s in the box?

4. Pairing and connecting

4.1. Connecting to a mobile phone/tablet

4.2. Connecting to a Bluetooth transmitter

4.3. Connecting to two Bluetooth devices simultaneously

5. How to reset to factory default setting?

6. LED indications

7. Charging

8. Product Specifications

1

11

10

9

7-88

6-7

5-6

5

2

4

Status LED indicator

For a Better Experience

www.avantree.com

User ManualWireless Receiver for Headphones

Clipper Pro

For a Better Experience

www.avantree.com

User ManualWireless Receiver for Headphones

Clipper Pro

Voice Dial (Siri) Press V+ and V- together once

Low batteryWhen connected, RED LED flash once per 5s.

When disconnected, RED LED flash once per 2s.

Any questions? Contact:

Support@avantree.com

Self-service Support:• More FAQs on support.avantree.com• 100+ Step by step video Guide – youtube.com/avantree/playlists

Telephone Support (Mon-Fri): • USA / CANADA +1 800 232 2078 (EN, PST 9am-5pm)• EU / Asia telephone No. refer to http: //www.avantree.com/contact-us