www.ureach-inc.comthe Expert of Duplicators

SATA DOM DuplicatorUser GuideV1.0

2

Disclaimer of WarrantiesDisclaimer of WarrantiesAll UREACH flash duplicators are made specifically for data backup with legal

authorities from copyright owners. Any unauthorized action of copyright is

strictly prohibited, and UREACH-INC disclaims all warranties or representations

of illegal actions by users.

UREACH-INC also disclaims any liability for any loss or damage due to

not being able to perform its undertakings or provide any of the services

attributable to any events or circumstances beyond our control. Users agree

and accept all statements above as soon as purchasing our products.

This manual contains materials that should be intended for personal use. All

right reserved. No part of this manual may be reproduced, transmitted or

transcribed without the expressed written permission of the manufacturer .The

information present in this manual is subject to change without prior notice.

3

Before you start Important Notice• Read the complete operation instruction carefully contributes to better operation.

• Make sure the source device is correct and workable.

• To guarantee data consistency, it is strongly suggested that the capacity of

source and targets should be the same.

• It is strongly suggest to use “Copy+Compare” to achieve perfect duplication.

Safety Precautions• The warranty will expire if damage is incurred resulting from non-compliance with theses operating instructions.

• Never turn off the power while processing the firmware update.

• Use only approved power sources.

• The product is only suitable for operation in dry, dust free, clean environment.

• Do not allow liquids or foreign objects to enter. Failure to do so may severely damage your duplicator.

4

Index Content▪ Disclaimer of Warranties 2

▪ Before you start 3

▪ Index Content 4

♳ Introduction

1. Overview 5

2. Features 5

3. Package Contents 6

4. Product Overview 7

5. Other adapters that can be

applied 8

♴ Function Table 9

♵ Function Introduction

1. Copy 11

2. Compare 12

3. Copy+Compare 12

4. Erase 12

4.1 Quick Erase 13

4.2 Full Erase 13

4.3 DoD Erase 13

4.4 DoD Erase Comp 14

5. Utility 14

5.1 Show DOM Info. 14

5.2 Update System 15

5.3 System Info. 15

6. Setup 16

6.1 Copy Area 16

6.1.1 System and Files 16

6.1.2 All Partitions 16

6.1.3 Whole HDD 17

6.2 Skip Error 18

6.3 Erase Master 18

6.4 Unknown Format 18

6.4.1 Copy Unknown 18

6.4.2 Skip Unknown 19

6.5 Transfer Rate 19

6.6 Erase Pattern 19

6.6.1 ONE Byte 19

6.6.2 4MB Byte 19

6.7 Language 20

6.8 Restore Default 20

♶ FAQ 21

♷ Specification 22

Introduction 1

5

Introduction1.OverviewThis duplicator series is a high-end industrial standard SATA DOM duplicator that makes DOM duplication fast and easy. There is no computer or additional software required. It supports 1 to 7 targets duplication and high data transfer speed up to 3.9GB per minute. The three different copy modes (System and Files, All Partitions and Whole HDD) can satisfy various needs of duplication; "System and Files" copy mode is a fast copy mode that can copy only data area instead of copying entire source HDD, so it can greatly save elapsing time.

This series supports lots of interfaces including SATA DOM, mSATA, Micro SATA, CF, CFast through suitable adapters, which makes this product applicable on lots of different devices. In addition, it provides smart power control system. When copying is finished, the machine will automatically cut off the power of each port to protect HDD from damage during removal from the duplicator. The power of each port will be only be output when the operation is started. Besides Quick/Full Erase, it provides with DoD Erase and DoD EraseComp, which can completely erase the data from hard drives complying with Department of Defense standard (DoD 5220) and guarantee the data was completely deleted.

2.Features• Support high transmission speed up to 3.9GB/Min.• Support many kinds of interfaces including SATA, mSATA, MicroSATA, CF, and

CFast through adapters.• Automatic power control to protect HDD from the damage during insertion and

removal.• Standalone, no PC or other installation required.• Three duplication modes: “System and Files”, “All Partitions”, and “Whole HDD”

copy modes.• Instant power on and off. Easy to boot up without waiting time.• Easy firmware updating without complex procedure.• Support DoD Erase function which complies with the standard of Department

of Defense.

1 Introduction

6

3.Package Contents

Power Adapter/Power Cord

SATA DOM Adapter

SATA DOM Duplicator

User Guide

Introduction 1

7

4.Product OverviewA. System Overview

Back Side

Power Supply

Power Switch

Socket

Yellow: Powering

Green Flashing: ProcessingGreen Remaining: Pass

Red: Fail

LCD

Up Side

B. LCD ConfigurationForward

Backward

Confirm/OK

Cancel/Back

1 Introduction

8

5.Other adapters that can be applied

Adapter

mSATA ↑ SATA MicroSATA ↑ SATA CF ↑ SATA CFast ↑ SATA

Device supported

Function Table 2

9

Function TableFunction Description

1. CopyTo copy source DOM to multiple target DOMs. Refer to function “6.1 Copy Area” for 3 different copy mode selection.

2. Compare To compare data bit for bit between source and copied DOMs.

3. Copy+CompareIt makes copy first and then compare copied DOM with source DOM to ensure copied correctness.

4. EraseNote: Function 6.3 can select to erase source DOM or not

4.1 Quick EraseErase DOM’s index table only, it takes short time to execute this function.

4.2 Full EraseErase the whole DOM content.

4.3 DoD eraseErase DOMs three times complying with USA Department of Defense (DoD) standard.

4.4 DoD EraseCompErase DOMs three times complying with USA Department of Defense (DoD) standard, and compare data bit by bit to check if data is completely erased.

5. Utility

5.1 Show DOM info.Shows DOM’s basic information such as DOM’S model name and capacity.

5.2 Update System

5.2.1 Update BIOSTo update the system firmware via the DOM.

5.2.2 Create Update HDDTo format the DOM with a 2GB FAT partition in order to quickly save firmware in the DOM.

5.3 System Info.This function will show information of the duplicator system, including controller model number and software version.

2 Function Table

10

6. Setup

6.1 Copy AreaSetup copy mode.

6.1.1 System and filesSet to copy source HDD’s data area only.

6.1.2 ALL partitionSet to copy source HDD’s all partitions.

6.1.3 Whole HDDSet to copy the whole source HDD.

6.2 Skip ErrorSet the error volume of source DOM that you want to ignore while copying. (0 - 65535)

6.3 Erase MasterSetup to erase source DOM or not.

6.3.1 DisableDisable erase source DOM.

6.3.2 EnableEnable erase source DOM.

6.4 Unknown Format

6.4.1 Copy unknownCopy unknown area when the device can not identifythe format.

6.4.2 Skip unknownSkip copying unknown area when the device can notidentify the format.

6.5 Transfer RateSelect the proper transfer rate UDMA 2 - 4. 4 is the fastest.

6.6 Erase Pattern

6.6.1 ONE ByteA random character to be written into every byte.

6.6.2 4MB ByteA set of random characters to be written into a set of area.

6.7 LanguageSelect preferred language.

6.8 Restore DefaultBack to original manufacturer setting.

Function Introduction 3

11

Function Introduction1.CopyIt copies data from source DOM to target DOM. Please make sure you have chosen the correct copy mode you would like to use. About the three copy modes, please refer to function [6.1 Copy Area] for details.

DOM Duplicator1.Copy

The default setting of [6.1 Copy Area] is “System and Files”.

Stepsa. Plug in the source DOM and target DOMs, and then select function [1. Copy].

CopySearching Source

Analyzing Source

Copy 21.9G 2 readyTarget

Copy 967M 1 readyTarget

CopySearching Source

Analyzing Source

Copy 21.9G 2 readyTarget

Copy 967M 1 readyTarget

b. After finishing analyzing the source and all the targets are ready, the system will start copying automatically.

Copy X 2 21.9G15:5 82% (3)18.0G

Function Total data size

Copied data size

Copied time and %

The slowestport

3 Function Introduction

12

c. When finishing copying, the copied result will be showed on the LCD.

Pass: 2 Fail: 0Time 19:19

Quantity of copy pass Quantity of copy fail

Total copied time

2.CompareThis function is used to check the correctness of the copying result. After finishing copying, go to function 2 and press OK to start executing comparingprocess.

DOM Duplicator2.Compare

3.Copy+CompareThis function makes copy first and then compare copied target DOM with the source DOM automatically to ensure the correctness of the copied result.

4.EraseThis function is used to delete the data in your DOM. Please choose the appropriate erase method when you would like to dispose or reuse the DOMs.

DOM Duplicator4. Erase

1.Function [6.3 Erase Master] is to determine if erasing source DOM or not. The default setting is “Disable erase master ”.2.The function can be stopped while processing by pressing [ESC] for about 3~4 seconds.

Function Introduction 3

13

4.1 Quick EraseThe function will ONLY erase the index of the DOM, which is the quickest way to erase it. Quick Erase will damage the data in DOM, please make sure you have backup all important data before using this function.

4.2 Full EraseThe function will erase the whole sectors on the target DOM. It will take longer time than quick erase. Full Erase will damage the data in DOM, please make sure you have backup all important data before using this function.

4.3 DoD EraseDoD Erase is an erasing method that complies with the U.S.A. Department of Defense (DoD) standard. It can guarantee the data was fully deleted by erasing the DOM bit by bit three times. DoD Erase will damage the data in DOM, please make sure you have backup all important data before using this function.

Stepsa. Press OK to execute erasing.

DoD ErasePrepare Pattern

Erasing HDDDoD Erase 5:52

b. The result will be showed on the LCD when DoD Erase is finished.

DoD ErasePass:2 Fail:0

3 Function Introduction

14

4.4 DoD Erase CompBesides DoD erase, this function will also execute compare function to make sure the random bit was correctly written. This way of erase i s t o e rase DOM ove r each sec to r t h ree t imes : t he f i r s t t ime w i t h z e ros (0x00), second t ime with 0xFF and the third t ime with random characters. There is one f inal pass to compare random characters by reading. This function will damage the data in DOM, please make sure you have backup all important data before using this function.

step1. 0x00100GB

20GB

20GB

20GB

40GB

step2. 0xFF step3. Random step4. Compare

※The erasing time of DoD Erase mode is three times longer than Full Erase mode, and the time of DoD Erase Comp is four times longer than Full Erase mode.

5.Utility5.1 Show DOM Info.This function will show DOM's basic information such as DOM capacity and model number.

[01]64GTS1GSDOM22V

Port No.

DOM Capacity

DOM mode No.

Function Introduction 3

15

5.2 Update SystemThis function is used to update the system firmware. Please follow the following steps to execute “Update System”.

a. Select function [5.2.2 Create Update HDD].

[Update System]2.Create Update HDD

b. Format DOM.(Create a 2GB FAT partition)

Do FORMAT HDD#1 Confirm ?

The purpose of formatting DOM before updating system is because creating a 2GB FAT partition can speed up the updating process.

c. Download the BIOS from PC to your DOM.d. Plug in the DOM into the Port#1, and select [Function 5.2.1] to update BIOS.

5.3 System Info.This function shows the information of the duplicator including model name and firmware version.

DOM Dupe 1-7Ver: 2.29.7

3 Function Introduction

16

6.Setup6.1 Copy Area

6.1.1 System and FilesIt will copy source DOM’s System and Files instead of the whole HDD. The system will analyze the source HDD and identify the data area to copy. As long as the source DOM’s data within the target HDD’s space, the copy will be processed.

[Copy Area] System and Files

When choosing “System and Files Copy”,only 20G data will be copied,and it just takes 6.2% time compared to “Whole HDD Copy’.The target HDD will be exactly the same as source HDD after copy.

[System and Files] only supports FAT, NTFS and LINUX EXT2/EXT3/EXT4 for quick copy.

6.1.2 All PartitionsThis mode will copy all of the partitions bit by bit including the free space. Thecapacity of target HDD has to be larger than all the partitions.

[Copy Area] All Partitions

Function Introduction 3

17

When choosing “All Partitions Copy”,only 120G data will be copied,and it just takes 37.5% time compared to “Whole HDD Copy’.The target HDD will be exactly the same as source HDD after copy.

6.1.3 Whole HDDThis mode will copy the entire HDD, regardless of the content, format, partition, or free space, and it will take much more time to duplicate the source DOM completely.

[Copy Area] Whole HDD

When choosing “Whole HDD Copy”,completed 320G HDD will be copied,and it just takes the longest time. The target HDD will be exactly the same as source HDD after copy.

After copy, the remaining space in the copied DOM can be used by PC for further partitioning.

3 Function Introduction

18

6.2 Skip ErrorThis function can set the number of errors you would like to skip during the copying process.

[Skip Error] 0

If the DOM is very critical for content correctness, it is strongly recommended to keep the Skip Error to be “0”.

6.3 Erase MasterThis function is used to set if erasing the source DOM or not. Please make sure this setting before you execute erase function.

[Erase Master] Disable

[Erase Master] Enable

6.4 Unknown FormatThis function is used to set if copying the unknown format area or not.

6.4.1 Copy UnknownThis setting allows copying the unknown area that the system can’t identify its format.

[Unknown Format] Copy Unknown

Function Introduction 3

19

6.4.2 Skip UnknownThis setting is to skip the unknown area that the system can’t identify its format during the copying process.

[Unknown Format] Skip Unknown

6.5 Transfer RateYou can select the best transfer rate from UDMA 2 to UDMA 4 for your DOMduplication progress. If you are not confident on the DOM quality or you finda high failure rate on copy or compare. It is recommended to slow down theUDMA mode.

[Transfer Rate] UDMA 3

6.6 Erase PatternThis setting is used to select different erase methods.

6.6.1 ONE ByteA random character to be written into every byte.

[Erase Pattern] One Byte

6.6.2 4MB ByteA set of random character to be written into a set of area.

[Erase Pattern] 4MB Byte

3 Function Introduction

20

6.7 LanguageThis setting is to set the system’s language interface.

[Language] English

6.8 Restore DefaultThis setting is to go back to the manufacturer’s default setting.

FAQ 4

21

FAQQ1: Does it need waiting time for boot on and shut down?

A1: This system supports instant power on and off, no need of waiting time.

Thus, you can turn it off when it is not in use.

Q2: Can I interrupt the copy task while it is not finished?

A2: Yes, the program (copy, compare and erase) can be stoop while it is

processing by pressing [ESC] for about 3~4 seconds.

Q3: Will it be safe if I remove the DOM right after copy process?

A3: Yes, the device will automatically cut off power of each port to

protect DOM from damage during removal from the duplicator. The power

of each port will be only be output when the operation is started.

Q4: Except for SATA DOM, can this duplicator copy other HDDs or flash?

A4: Yes, this SATA DOM duplicator can also support SATA HDD, IDE HDD,

mSATA, Micro SATA, CF, and CFast. Most of them need additional

adapters. Please contact your local agent for the accessories.

5 Specification

22

SpecificationProduct Name SATA DOM

Target 1:7

Operation Stand Alone

Interface SATA

Other interfaces supported mSATA/ Micro SATA/ CF/ CFast

Power Supply(Adapter) 12V, 5A

Buffer 128MB

Display Monochrome LCD display

Control Button 4 push buttons ( ▲ , ▼ ,OK, ESC )

LED LED(Yellow/Green/Red) on each slot

Supported Language English, Japanese

Temperature Working 5ºC~45ºC

Storage -20ºC~85ºC

Humidity Working 20%~80%

Storage 5%~95%

Safety FCC, CE, RoHS

www.ureach-inc.com