Us 180 NUMTools P Under Windows7

7/17/2019 Us 180 NUMTools P Under Windows7

http://slidepdf.com/reader/full/us-180-numtools-p-under-windows7 1/17

NUM CorporationEngineering Department

Axium PowerSoftware under OS

Windows 7

NUM INFORMATION

US N° 180 1/17

Date:12/23/10

NUM Corporation Phone: 630-505-7722 603 East Diehl Road, Suite 115 Fax: 630-505-7754Naperville, IL 60563-1477 USA Web: www.num.com

Windows 7 – Professional and Home Premium – 32 Bit Version

NUMTools Workshop (ver. P) Installation

Windows 7 generally supports 32- and 64-bit architectures (x86 and x64). ForNUMTools version “P” a 32-Bit OS is definitely required, because the Vista32X_Waydrivers will ONLY work with a 32-bit operating system.

The Vista32 X_Way drivers rev. 2.6 are not part of the NUM Tool Workshoppackage. They could be obtained separately either from:

NUM FTP Download Scheneider drivers v2.6or

Schneider Electric - Driver Pack V2.6 The Schneider communication drivers pack V2.6 have to be installed before the NUMTool Workshop is loaded. If the drivers are not loaded prior to attempting to load NUMTool Workshop then the following error is displayed:

Installing Unitelway and XIP Windows VISTA/7 Drivers

1. Run the _installdrivers.html file on the installation CD.This will display the following screen:-

ftp://NUMC505:[email protected]/Schneider_Drivers_Pack_V26.zip

http://www.global-download.schneider-electric.com/852575620060F38B/all/C125713F005265E2C12574960036F229?OpenDocument&L=RU~RU&

http://www.global-download.schneider-electric.com/852575620060F38B/all/C125713F005265E2C12574960036F229?OpenDocument&L=RU~RU&

ftp://NUMC505:[email protected]/Schneider_Drivers_Pack_V26.zip



Axium Power

Software under OSWindows 7

NUM INFORMATION

US N° 180 2/17

Date:12/23/10


2. Select required driver to load (under Windows VISTA32) :-

a) UNI-TELWAY – Port Com Setup V2.0 IE10 and/or

b) XIP – X_WAY on TCP/IP Setup V2.0 IE10

Note: Selecting either of the above will load in the Drivers Manager before the driver.

3. On the message “Pending Schneider Driver Manager for Vista32” – ClickInstall

4. Follow the on screen prompts

5. Drivers will install with no Finish notification! – Restart PC

Installing NUM Tool Workshop (Ver. P00)

1. Insert CD into PC – AutoPlay displays the below message.Click on Run setup.exe



Axium Power


NUM INFORMATION

US N° 180 3/17

Date:12/23/10


2. “Do you want to allow the following program from an unknownpublisher to make changes to this computer?”

Message posted - click Yes to continue – Install shield runs.

3. NUM Tool welcome screen page: click Next to continue.

4. License Agreement screen page: click Yes to continue.

5. Information screen page:click Next to continue.

6. Choose Destination Location screen page: click Next if Location is OK orbrowse to desired location.

7. Selection of Software installation package screen page: Leave Install NUM

Tool and HMI selected - click Next to continue



Axium Power


NUM INFORMATION

US N° 180 4/17

Date:12/23/10


8. Selection of the Human Machine Interface screen page: click Next tocontinue.(PC Panel MMI and PC Standard MMI (Apex screens) can be selected if required)

9. Setup Type screen page: Leave Complete selected then click Next tocontinue.

10. Licence message page: click OK to continue

11. User Licence PLCTool and SETTool page: lease enter User Name /Company Name / User Licence – click Next to continue.

12. Select Program Folder screen page: click Next for default location(Location can be changed if necessary).

13. Select communication and driver installation screen page: Please selectthe desired communication – (Com – serial link is default). Then click Next tocontinue.



Axium Power


NUM INFORMATION

US N° 180 5/17

Date:12/23/10


14. Select language screen page: select Desired Language – click Next tocontinue.

15. Information of installation screen page: click Next to continue.

16. Setup Status screen page: leave as software is configured.

17. “DllRegisterServer in C:\Program Files\CommonFiles\microsoftshared\DAO\dao350.dll succeeded”.

When message is displayed just click click OK to continue

18. SYSTEM UPGRADEMachine Manager required Borland Database Engine

Would you like to install Borland components?

When message is displayed just click Yes to continue

19. Registry Editor message page: click Yes to continue.

20. Second Registry Editor message page: click OK to continue

21. Install Shield Wizard Complete screen page: click Finish to continue

22. Remove installation CD and reboot PC.



Axium Power


NUM INFORMATION

US N° 180 6/17

Date:12/23/10


XIP-Driver Setup

Setup the CNC Parameters with PC Standard MMI (Apex).

The XIP driver uses the following NC parameters:P100 – N1 - XIP Xway address = 3F (Hex)P124 – CNC TCP/IP Address = 192.168.0.254P125 – CNC Subnet Mask = 255.255.255.0

P100 N1 corresponds to the Station Address in Step 3 below. Range is 0 to 3F Hex (0to 63 decimal)

Setting of the PC Network Adaptor:IP address = 192.168.0.150Subnet Mask = 255.255.255.0

Remark: The above values for parameters and Network settings are example values only.

1. Power up CNC – Connect PC to CNC TCP/IP adaptor with a Cross (X) network cable.

2. Set-up the Network Adaptor Settings(Control Panel > Network and Internet > Network and Sharing Centre > Change AdaptorSettings)In the below example IP Version 4 is modified.

At this point it is possible to ping the CNC from the PC – i.e. ping 192.168.0.254 andcheck response.



Axium Power


NUM INFORMATION

US N° 180 7/17

Date:12/23/10


3. Open Communication & Language parameter program

(Start -> All Programs -> NUM Tool Win Vista32 -> Communication -> Communication &Language parameter).

Ensure Station under NUM Tool andNUMpass CNC configuration, if NumPass isloaded, is set to CNC P100 N1 value. 3F(hex) in this example

(CNC Parameter 100 value - Range is 0 to 3FThis equal 0 to 63 decimal)

4. Ensure XIP is selected in Type of Communication box.

5. Enter Station Value in NUM Tool Box and NUMpass CNC configuration Box (ifNumpass is loaded).This value equals CNC parameter P100 – N1 . (Set to 3F Hex in this example)

6. Click Validate - “Communication is now set to XIP01” is displayed in the LOADINGwindow.(on subsequent running of the program the loading window will several references to XIP01)

7. Click Configuration – This will display Schneider Drivers Management Properties :-

Select XIP Driver Tab.



Axium Power


NUM INFORMATION

US N° 180 8/17

Date:12/23/10


8. Click Configuration (Answer Yes to any questions allowing program to makechanges)

IF no XIP has been previously been set-up on the PC then the following warning will bedisplayed :

Click OK to continue

This will then display New XIP profile creation



Axium Power


NUM INFORMATION

US N° 180 9/17

Date:12/23/10


Under TCP/IP – Network Adaptor drop down box select the required Adaptor and click

OK (Note TCP/IP Address of PC as set in Step 2. – in this example 192.168.0.150)

This displays the following:

9. Click Bind (not necessary if already performed above).

Under TCP/IP – Network Adaptor Drop down box select the required Adaptor andclick OK (Note TCP/IP Address of PC as set in Step 2. – in this example 192.168.0.150)

10. Enter New Remote Host data as shown belowE.g. Station = CNC / XWAY address = 0 . 63 / IP Address = 192.168.0.254XWAY address = 0 . 63 - P100 N1 = 3F

Deselect Enable automatic detection.Ensure DNS is not selected

Enter Local host XWAY Address = 0.63Note Local Host and New remote host XWAY addresses must have a differentvalue.

11. Click Add button



Axium Power


NUM INFORMATION

US N° 180 10/17

Date:12/23/10


12. Click Save – Message “The new configuration has been saved successfully” – click OK

13. Under XIP menu bar– Select Reset – This Resets the XIP driver.(or Stop then Start)

14. Under Test menu select ICMP Ping > Select Ping

15. Close all windows and reboot PC and CNC – Important to do this.



Axium Power


NUM INFORMATION

US N° 180 11/17

Date:12/23/10


Testing XIP Communication

1. Open Communication & Language parameter program

2. Select Configuration > Select XWAY Test Tab

3. Under Driver box - Name: – Drop down menu - Select XIP

4. Change Remote address: to 0.63.0

5. Select Connect State in request box becomes Connected – icon is active.(there may be a slight delay)

6. Select Start - The request will flash red / yellow and the number will increment.

Com Port Set-up with Unitelway Driver

1. Run Communication & Language parameter program(Start -> All Programs -> NUM Tool Win Vista32 -> Communication ->Communication & Language parameter).

2. Ensure COM is selected in Type of Communication box.

3. Click Validate (There will be several references to COM in the Loading window)



Axium Power


NUM INFORMATION

US N° 180 12/17

Date:12/23/10


4. Click Configuration – This will display Schneider Drivers ManagementProperties :

5. Select UNITELWAY Driver Tab

6. Select Configuration. (Answer Yes to any questions allowing program tomake changes)

COM1 is the default Com port. An additional Com port may be shown ifusing a USB - RS232 device – in this

case ensure Force Virtual Com Port(shown below) is selected.

7. Select Edit – to display Station Parameters - the 3 tabs are displayed :-Set values as below.



Axium Power


NUM INFORMATION

US N° 180 13/17

Date:12/23/10


The Baud rate can be set from 300 to 115200bps.Ensure Unitelway and NumPLC are selected

8. Click OK to close Station Parameters.

9. Click Apply to Reset Unitelway Driver. Drivers Reset is OK is displayed

10. Click OK to exit Unitelway Configuration11. Click OK to exit Schneider Drivers Management

Testing Unitelway Communication

1. Connect Comms cable from NC to PC. (Port 0 in this case)

2. Configure Comms Port on control – P112 N0 = 00 / N1 = 55 / N2 = 01Port 0 / 115200 baud rate

3. Click Configuration – This will display Schneider Drivers ManagementProperties.

4. Select X_WAY Test tab.

5. Select Connect – State in request box becomes Connected – icon is active.

(there may be a slight delay while the correct baud rate is selected)

6. Select Start - The request will flash red / yellow and the number will increment.

7. Select Stop – Select Disconnect. – State to Disconnected.

8. Select OK to close Drivers Manager.

9. Select Exit to close Communication & Language parameters



Axium Power


NUM INFORMATION

US N° 180 14/17

Date:12/23/10


HSL PCI Set-up – Windows 7

The document details HSL PCI setup – Driver installation - with Windows 7 (32 Bit)

The HSL PCI C101 board is manufactured by MOXA and has a Num part number of0202206297.

Download the Drivers from the MOXA website – C101.EXE (self extracting zip File)

1. With PC Power off – cable disconnected – fit the HSL PCI card to the PC.(Use a wrist strap – antistatic).

2. Power-up PC.

3. Select the C101.EXE - Right Click – Select Troubleshoot compatibility.

The C101.exe file is run in compatibility mode to ensure it loads the drivers in thec:\windows\System32 folder.

4. Select Try recommended Settings



Axium Power


NUM INFORMATION

US N° 180 15/17

Date:12/23/10


5. Test compatibility settings for the program is displayed – Select Start program button

6. When this message appears: “Do you want to allow the following program from anunknown publisher to make changes to this computer ” - Press YES button.

7. A DOS window appears a question displayed “Continue Extraction?”Press Y followed by enter key.

This extracts the necessary files to the C:\Windows\System32 directory (folder).Dos window closes.

8. The Test compatibility settings for the program screen is displayed – Select Cancel button.

9. Go to Device Manager

10. Right Click PCI serial port(Warning symbol on icon – showing a driver problem)



Axium Power


NUM INFORMATION

US N° 180 16/17

Date:12/23/10


11. Select Update driver software.

12. Click Browse my computer for driver software.

13. Browse to C:\Windows\System32 folder - Click Next

Searching message is displayed.



Axium Power


NUM INFORMATION

US N° 180 17/17

Date:12/23/10


14. Windows Security image – acknowledge:

15. Click Install this driver software anyway.

16. Message “Installing Driver software” is displayed.

17. Message “Windows has successfully updated your driver software”

18. Click close

19. Restart PC

Documents

Us 180 NUMTools P Under Windows7