Uploads_downloads_Computer Network Technician, OSS, L-3

JOB SPECIFICATION AND

SKILL TEST

JOB TITLE : Computer Network Technician, L-3 SUB-SECTOR : Computer Networks SECTOR : Computer Engineering

Council for Technical Education and Vocational Training National Skill Testing Board

Sanothimi, Bhaktapur, Nepal May 2006/Baishakh 2063

Revised

2

The National Skill Standard and Test was revised by: No. Name Designation Organization

1. Dr. Subarna Shakya Coordinator Head of Department & Associate Professor Department of Electronics and Computer Engineering Pulchowk Campus, Institute of Engineering (IOE)

2. Mr. Chandra Bhakta Nakarmi Member Director, National Skill Testing Board (NSTB) Council for Technical Education & Vocational Training (CTEVT) Sanothimi, Bhaktapur, Nepal

3. Mr. Nrip Dhoj Khadka Member Senior Instructor Department of Electronics and Computer Engineering Pulchowk Campus, Institute of Engineering (IOE)

4. Mr. Deepak Rauniyar Member First Vice President, Association of Computer Engineers Nepal (ACEN) Pulchok, Lalitpur, Nepal

5. Mr. Raju Shah Member Service Engineer, Hardware Department, Mercantile Communication Pvt. Ltd, Durbar Marg, Ktm.

6. Mr. Narayan Neupane Member Technical Trainer New Horizon Computer Learning Center, Jawalakhel.

7. Mr. Ram Krishna Desar Member Asst. Network Administrator Worldlink Communication Pvt. Ltd, Jawalakhel

8. Mr. Chhabi Bahadur Gurung Member Dy-Director, National Skill Testing Board (NSTB) Council for Technical Education & Vocational Training (CTEVT) Sanothimi, Bhaktapur, Nepal

9. Mr. Shreedhar Mohan Ranjit Member-Secretary Deputy Director, National Skill Testing Board(NSTB) Council for Technical Education & Vocational Training (CTEVT) Sanothimi, Bhaktapur, Nepal

10. Mr. Santosh Kumar Mahaseth Assistant Skill Testing Assistant, National Skill Testing Board (NSTB) Council for Technical Education & Vocational Training (CTEVT) Sanothimi, Bhaktapur, Nepal

Approved By: The Tripartite National Skill Testing Board- May 2006/2063 Baishakh

3

The National Skill Standard and Test was developed by:

1. Mr. Shreeram Nath Regmi Coordinator Director, CIT Department, IOE, Pulchwok

2. Mr. Harihar Thapaliya Member Director, Skill Testing Division, CTEVT

3. Mr. Arjun KC Standard Writer Vice President-Training, College of Software Engineering, Putalisadak

4. Mr. Raju Shrestha Member Computer Officer, National Planning Commission

5. Mr. Krishna Poudel Member Engineer, Nepal telecommunication Corp, Computer Department, Jawalakhel

6. Mr. Deepak Gautam Member Lecturer, MIS Director, IOE, Pulchwok

7. Mr. Nripa Dhoj Khadka Member Sr. Instructor, Dept. of Electronics and Computer Engineering, IOE, Pulchwok

9. Mr. Shreedhar Mohan Ranjit Member-Secretary Dy. Director, Skill Testing Division, CTEVT

Approved By: The Tripartite National Skill Testing Board- 2001 (2057/058)

4

JOB SPECIFICATION

1

JOB TITLE : Computer Network Technician LEVEL : Three

2 JOB DESCRIPTION Computer Network Technician supports and maintains a basic network Systems on Windows and Linux Networking.

3 LIST OF TASKS

1. Identifying and connecting the different Components of Computer Systems including Motherboard, Processor, Storage Devices, Memory, Display Card, Sound Card , NIC and Modem.

2. Laying the LAN and preparing Cables as per requirement. 3. Identifying and connecting the basic Networking Components like Hub, NIC, Switch, Router, Modem, Wireless Components, Cables

and Connectors. 4. Installing the Client-Server based Operating System and Protocols like NetBios, IPX/SPX and TCP/IP. 5. Installing the Client Operating System and connecting to the Server. 6. Creating User and Group Accounts and assigning Rights and Permissions. 7. Sharing the Resources and assigning basic Permissions. 8. Installing and configuring Print Server and Clients. 9. Installing and configuring Email and Internet Client. 10. Troubleshooting and repairing Network and its Devices. 11. Installing Network Utility Software.

Note: Every year, the standard needs to be revised in line with the changes in Computer technology.

4 QUALIFYING NOTES (entry requirements)

1. Educational requirements: Should be able to read and write English and Nepali language. 2. Others: Should have 3 years of work experience and have completed 48 hrs of training on Networking. OR As per National Skill Testing Board (NSTB) rules with literate on English

5

TASK SPECIFICATION

5 TASK NO : 1 TASK TITLE : Identifying and connecting the different Components of Computer Systems including Motherboard, Processor, Storage Devices, Memory, Display Card, Sound Card , NIC and Modem. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

1.1 Identifies the Peripherals Components of the Computer Systems like Motherboard, Processor, Storage Devices, Memory, Display Card, Sound Card, NIC and Modem and connects them in the appropriate slot of Motherboard.

1.2 Supplies Power to the CPU and Peripheral Devices and confirms the initialization of the Computer Systems. 1.3 Set up basic Configuration from the CMOS Setup Menu.

6

7

TASK PERFORMANCE REQUIREMENTS

Power Supplies One set of Tool kit. One set Computer including Monitor, Motherboard, Processor, Harddisk, CD/DVD Drive, Display Card, RAM, Sound

Card, NIC, Modem

8

TASK PERFORMANCE STANDARDS

1.1 Identified the Peripherals Components of the Computer Systems like Motherboard, Processor, Storage Devices, Memory, Display Card, Sound Card, NIC and Modem and connected them in the appropriate slot of Motherboard.

1.2 Supplied Power to the CPU and Peripheral Devices and confirmed the initialization of the Computer Systems. 1.3 Set up basic Configuration from the CMOS Setup Menu.

7

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE

APPLIED CALCULATIONS

GRAPHIC INFORMATION

SAFETY AND HYGINE

1

1.1

1.2

1.3 1.4

Basic knowledge of different Components of Computer Systems. Concept of basic operation of Computer Systems.

Basic knowledge of Processors. Working concepts of Computer Memory and Storage

Devices.

8

TASK PERFORMANCE TEST (Skill Assessment)

11

TASK TITLE: Identifying and connecting the different Components of Computer Systems including Motherboard, Processor, Storage Devices, Memory, Display Card, Sound Card , NIC and Modem.

TASK NO : 1

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12

TEST FACTORS AND ITEMS

STANDARD MET

STANDARD NOT MET (comments)

DID THE CANDIDATE? 1.1 Identify the Peripherals Components of the Computer

Systems like Motherboard, Processor, Storage Devices, Memory, Display Card, Sound Card, NIC and Modem and connect them in the appropriate slot of Motherboard.

1.2 Supply Power to the CPU and Peripheral Devices and confirm the initialization of the Computer Systems.

1.3 Set up basic Configuration from the CMOS Setup Menu.

9

TASK SPECIFICATION

5

TASK NO : 2 TASK TITLE : Laying the LAN and preparing Cables as per requirement. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

2.1 Prepares the Layout of LAN. 2.2 Selects the location of Network Components like Server, Hubs, Switches, Wireless Components, Routers and Workstations. 2.3 Identifies the different Cables and Connectors. 2.4 Identifies the structure of UTP Cables. 2.5 Identifies the types of UTP Cables. 2.6 Identifies the RJ-45 Connector and UTP Clamper. 2.7 Connects the RJ-45 Connector in the UTP Cable. 2.8 Checks the Cable against Short-Circuit and Continuity using LAN Meter (Cable Tester).

10

7


Power Supplies One set of Tool kit. Cables & Connector, NIC, Hub, Switch, Router, Modem, Wireless Components Clamper: RJ-45, RJ-11

8


2.1 Prepared the Layout of LAN. 2.2 Selected the location of Network Components like Server, Hubs, Switches, Wireless Components, Routers and Workstations. 2.3 Identified the different Cables and Connectors. 2.4 Identified the structure of UTP Cables. 2.5 Identified the types of UTP cables. 2.6 Identified the RJ-45 Connector and UTP Clamper. 2.7 Connected the RJ-45 Connector in the UTP Cable. 2.8 Checked the Cable against Short-Circuit and Continuity using LAN Meter (Cable Tester)

11

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

2

2.1

2.2

2.3

Concept of different Network Topology. Knowledge of advantage and disadvantages of different Network Topologies.

Basic knowledge of different Transmission Media.

12


11

TASK NO : 2 TASK TITLE : Laying the LAN and preparing Cables as per requirement. JOB TITLE : Computer Network Technician, L-3

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12

TEST FACTORS AND ITEM

STANDARD MET


DID THE CANDIDATE?

2.1 Prepare the Layout of LAN. 2.2 Select the location of Network Components like Server, Hubs,

Switches, Wireless Components, Routers and workstations. 2.3 Identify the different Cables and Connectors. 2.4 Identify the structure of UTP Cables. 2.5 Identify the types of UTP Cables. 2.6 Identify the RJ-45 Connector and UTP Clamper. 2.7 Connect the RJ-45 Connector in the UTP Cable. 2.8 Check the Cable against Short-Circuit and Continuity using LAN

Meter (Cable Tester).

13

TASK SPECIFICATION

5 TASK NO : 3 TASK TITLE : Identifying and connecting the basic Networking Components like Hub, NIC, Switch, Router, Modem, Wireless Components, Cables and Connectors. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

3.1 Identifies the basic Network Components; Network Cables, NIC, Hub, Switch, Router, Modem, Wireless Components and Connectors.

3.2 Clamps the Connectors into the Cable & checks the Connectivity. 3.3 Connect Network Components in Peer to Peer connection. 3.4 Makes physical connection of Network Components.

14

7


Power Supplies One set of Tool kit. Cables & Connector, NIC, Hub, Switch, Router, Modem, Wireless Components Clamper: RJ-45, RJ-11

8


3.1 Identified the basic Network Components; Network Cables, NIC, Hub, Switch, Router, Modem, Wireless Components and Connectors.

3.2 Clamped the Connectors into the Cable & checked the Connectivity. 3.3 Connected Network Components in Peer to Peer connection. 3.4 Made physical connection of Network Components.

15

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

3

3.1

3.2

3.3 3.4

3.5

Concept of Computer Networks including Layer Architecture of Networks.

Basic concepts of different Network Components.

Basic working principle of Hubs, Switches and Routers. Basic knowledge of Routing

Concept of different Network Computing Models (Client-Server, Distributed, Centralized and Peer to Peer)

16


11

TASK TITLE : Identifying and connecting the basic Networking Components like Hub, NIC, Switch, Router, Modem, Wireless Components, Cables and Connectors.

TASK NO : 3

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE? 3.1 Identifiy the basic Network Components; Network Cables, NIC, Hub,

Switch, Router, Modem, Wireless Components and Connectors. 3.2 Clamp the Connectors into the Cable & check the Connectivity. 3.3 Connect Network Components in Peer to Peer connection. 3.4 Make physical connection of Network Components.

17

TASK SPECIFICATION

5

TASK NO : 4 TASK TITLE : Installing the Client-Server based Operating System and Protocols like NetBios, IPX/SPX and TCP/IP. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

4.1 Prepares a Systems with minimum Hardware requirements for installation of Server. 4.2 Collects required Software. 4.3 Creates necessary Disk partition and formats. 4.4 Starts installation. 4.5 Selects the Disk partition, Drive and Folder name to install the Operating System. 4.6 Installs the Driver files for necessary hardware Devices. 4.7 Accepts the License Agreement. 4.8 Enters the Computer Name. 4.9 Selects the number of Users of license required. 4.10 Adds and configure the necessary Protocol like NetBios, IPX/SPX and TCP/IP. 4.11 If the DHCP Sever already exists in the Network, it selects the option to obtain the IP address from DHCP Server. 4.12 If there is no DHCP Server, it plans for IP addressing scheme and accordingly enter the IP address and Subnet mask. 4.13 Sets the Password for Server Administrator 4.14 Selects the different Components of Operating System as required 4.15 Makes settings for Time zone and Display Adaptor. 4.16 Completes the installation Process.

18

7


Power Supplies One set Computer including Monitor, Motherboard, Processor, Harddisk, CD/DVD Drive, Display Card, RAM,

Sound Card, NIC, Modem Necessary Software

8

TASK PERFORMANCE STANDARD

4.1 Prepared a Systems with minimum Hardware requirements for installation of Server. 4.2 Collected required Software. 4.3 Created necessary Disk partition and formats. 4.4 Started installation. 4.5 Selected the Disk partition, Drive and Folder name to install the Operating System. 4.6 Installed the Driver files for necessary hardware Devices. 4.7 Accepted the License Agreement. 4.8 Entered the Computer Name. 4.9 Selected the number of Users of license required. 4.10 Added and configured the necessary Protocol like NetBios, IPX/SPX and TCP/IP. 4.11 Selected the option to obtain the IP address from DHCP Server if the DHCP Sever already existed in the Network. 4.12 Planned for IP addressing scheme and accordingly entered the IP address and Subnet mask if there is no DHCP Server. 4.13 Set the Password for Server Administrator 4.14 Selected the different Components of Operating System as required 4.15 Made settings for Time zone and Display Adaptor. 4.16 Completed the installation Process.

19

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

4

4.1

4.2

4.3

4.4

4.5 4.6

Knowledge of basic feature of the Client-Server Network Systems. Knowledge of files Systems like FAT16, FAT32 , NTFS and EXT3. Knowledge of Devices Driver files

Working Concept of Network Protocol Knowledge of IP addressing schemes Basic concept of Workgroup and Domain Model.

20


11

TASK TITLE: Installing the Client-Server based Operating System and Protocols like NetBios,IPX/SPX and TCP/IP.

TASK NO : 4

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE? 4.1 Prepare a Systems with minimum Hardware requirements for

installation of Server. 4.2 Collect required Software. 4.3 Create necessary Disk partition and formats. 4.4 Start installation. 4.5 Select the Disk partition, Drive and Folder name to install the

Operating System. 4.6 Install the Driver files for necessary hardware Devices. 4.7 Enter the Computer Name. 4.8 Add and configure the necessary Protocol like NetBios, IPX/SPX and

TCP/IP. 4.9 Select the option to obtain the IP address from DHCP Server if the

DHCP Sever already exist in the Network. 4.10 Plan for IP addressing scheme and accordingly enter the IP address

and Subnet mask if there is no DHCP Server. 4.11 Set the Password for Server Administrator 4.12 Select the different Components of Operating System as required 4.13 Complete the installation Process.

21

TASK SPECIFICATION

5 TASK NO : 5 TASK TITLE : Installing the Client Operating System and connecting to the Server. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

5.1 Identifies the Client Operating System that has to be installed. 5.2 Checks whether the NIC card is plugged in the Clients Computer or not. 5.3 Identifies the NIC, which is going to be installed in the Systems. 5.4 If NIC is not plugged, opens the Casing and plugs the NIC in the appropriate Slot of the Motherboard. 5.5 Closes the Casing tightly and starts the Systems. 5.6 Select the Control Panel and runs the program for Hardware Devices settings. 5.7 Gives the appropriate path for Driver files and proceeds 5.8 Confirms the completion of installation process. 5.9 Installs the Protocol so as to match the Protocol installed in the Server 5.10 Assigns the correct IP address if the server is running TCP/IP protocol. 5.11 Plans whether to Workgroup Model or Domain Model. 5.12 For the Workgroup Model gives the Workgroup Name in Network Settings. 5.13 For the Domain Model, enters the Domain name in which you want to register your Client. 5.14 Restarts the Systems and log on to the Server using the Administrator User Account. 5.15 Confirms connection between Server and Client if the log on process is completed successfully. 5.16 For TCP/IP Networks, uses the PING Command to check the Connectivity.

22

7


Power Supplies One set Computer Systems, NIC. Necessary Software

8


5.1 Identified the Client Operating System that has to be installed. 5.2 Checked whether the NIC card is plugged in the Clients Computer or not. 5.3 Identified the NIC, which is going to be installed in the Systems. 5.4 Opened the Casing and plugged the NIC in the appropriate Slot of the Motherboard if NIC is not plugged. 5.5 Closed the Casing tightly and starts the Systems. 5.6 Selected the Control Panel and run the program for Hardware Devices Settings. 5.7 Gave the appropriate path for Driver files and proceeded. 5.8 Confirmed the completion of installation process. 5.9 Installed the Protocol so as to match the Protocol installed in the Server 5.10 Assigned the correct IP address if the server is running TCP/IP protocol. 5.11 Planed whether to Workgroup Model or Domain Model. 5.12 For the Workgroup Model gave the Workgroup Name in Network Settings. 5.13 For the Domain Model, entered the Domain name in which you want to register your Client. 5.14 Restarted the Systems and log on to the Server using the Administrator User Account. 5.15 Confirmed connection between Server and Client if the log on process is completed successfully. 5.16 For TCP/IP Networks, used the PING Command to check the Connectivity.

23

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

5

5.1 5.2 5.3

Knowledge of different Client Operating System Knowledge of Client-Server Architecture. Basic working knowledge TCP/IP Utility.

24


11

TASK TITLE: Installing the Client Operating System and connecting to the Server.

TASK NO : 5

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE? 5.1 Identify the Client Operating System that has to be installed. 5.2 Check whether the NIC card is plugged in the Clients Computer or not. 5.3 Identify the NIC, which is going to be installed in the Systems. 5.4 Open the Casing and plug the NIC in the appropriate Slot of the

Motherboard if NIC is not plugged. 5.5 Run the Control Panel and run the program for Hardware Devices

settings. 5.6 Select the appropriate path for Driver files and proceed. 5.7 Confirm the completion of installation process. 5.8 Install the Protocol so as to match the Protocol installed in the Server 5.9 Assign the correct IP address if the server is running TCP/IP protocol. 5.10 Give the Workgroup Name in Network Settings for the Workgroup

Model. 5.11 Enter the Domain name in which you want to register your Client for

the Domain Model. 5.12 Log on to the Server using the Administrator User Account. 5.13 Use the PING Command to check the connectivity for TCP/IP

Networks,.

25

TASK SPECIFICATION

5 TASK NO : 6 TASK TITLE : Creating User and Group Accounts and assigning Rights and Permissions. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

6.1 Plans for creating the Users and Group Accounts as per the requirement. 6.2 Log on to the Server with the appropriate Rights and runs the User Administration Tools. 6.3 Creates a User Template if required to create a large number of User Accounts with same Properties and Rights. 6.4 Makes appropriate Account Policy for Passwords like whether the User can change his password by himself or not. 6.5 Sets the Password Expiry Date as required. 6.6 Creates a Profile and Script for User to customize the Users Desktop. 6.7 Log on using the previously created User Account and verifies that it works as per settings. 6.8 Assigns User into different Groups and defines Permissions.

26

7


Power Supplies One set Computer Systems with Client Operating System. Necessary Software

8


6.1 Planed for creating the Users and Group Accounts as per the requirement. 6.2 Logged on to the Server with the appropriate Rights and run the User Administration Tools. 6.3 Created a User Template if required to create a large number of User Accounts with same Properties and Rights. 6.4 Made appropriate Account Policy for Passwords like whether the User can change his password by himself or not. 6.5 Set the Password Expiry Date as required. 6.6 Created a Profile and Script for User to customize the Users Desktop. 6.7 Logged on using the previously created User Account and verified that it worked as per settings. 6.8 Assigned User into different Groups and defined Permissions.

27

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

6

6.1 6.2 6.3

Knowledge of Users and Group. Knowledge of Defaults User and Group Account. Knowledge of different Permission Level.

28


11

TASK TITLE: Creating User and Group Accounts and assigning Rights and Permissions.

TASK NO : 6

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE?

6.1 Plan for creating the Users and Group Accounts as per the requirement. 6.2 Log on to the Server with the appropriate Rights and run the User

Administration Tools. 6.3 Create a User Template if required to create a large number of User

Accounts with same Properties and Rights. 6.4 Make appropriate Account Policy for Passwords like whether the User

can change his password by himself or not. 6.5 Set the Password Expiry Date as required. 6.6 Create a Profile and Script for User to customize the Users Desktop. 6.7 Log on using the previously created User Account and verify that it

work as per settings. 6.8 Assign User into different Groups and define Permissions.

29

TASK SPECIFICATION

5 TASK NO : 7 TASK TITLE : Sharing the Resources and assigning basic Permissions. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

7.1 Plans the Resources Access Controlling Policy for the Users. 7.2 Log on to the Systems as a User with appropriate Rights in the Computer whose Resource is to be shared for Network Users. 7.3 Shares the Storage Resources. 7.4 Enters the Share Name and assigns the appropriate Share Level Permissions to the User 7.5 Log on from another Client Computer and verifies the Resource Access. 7.6 Makes necessary plan for assigning permissions on different files and folders for different users and groups. 7.7 Assigns Read, Write, Modify and full control as per requirement. 7.8 Log on from the Client with those User Account and verifies the Permission.

30

7


Power Supplies One set Computer Systems with Client Operating System. Necessary Software

8


7.1 Planed the Resources Access Controlling Policy for the Users. 7.2 Logged on to the Systems as a User with appropriate Rights in the Computer whose Resource is to be shared for Network Users. 7.3 Shared the Storage Resources. 7.4 Entered the Share Name and assigned the appropriate Share Level Permissions to the User. 7.5 Logged on from another Client Computer and verified the Resource Access. 7.6 Made necessary plan for assigning permissions on different files and folders for different users and groups. 7.7 Assigned Read, Write, Modify and full control as per requirement. 7.8 Logged on from the Client with those User Account and verified the Permission.

31

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

7

7.1

7.2

7.3

Knowledge of Resources Sharing. Knowledge of Share Level Permissions for Resources. Knowledge of Resource Access Policy.

32


11

TASK TITLE: Sharing the Resources and assigning basic Permissions. TASK NO : 7

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE?

7.1 Plan the Resources Access Controlling Policy for the Users. 7.2 Log on to the Systems as a User with appropriate Rights in the

Computer whose Resource is to be shared for Network Users. 7.3 Share the Storage Resources. 7.4 Enters the Share Name and assign the appropriate Share Level

Permissions to the User 7.5 Log on from another Client Computer and verify the Resource Access. 7.6 Make necessary plan for assigning permissions on different files and

folders for different users and groups. 7.7 Assign Read, Write, Modify and full control as per requirement. 7.8 Log on from the Client with those User Account and verify the

Permission.

33

TASK SPECIFICATION

5 TASK NO : 8 TASK TITLE : Installing and configuring Print Server and Clients. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS

8.1 Plans Resources for the Print Server along with the necessary Software and driver. 8.2 If the Vendor supplied Software is not available tries using the Standard Drivers available in the Operating System. 8.3 Performs the Standard installation Procedure. 8.4 Completes the installation process and shares the Printer for Network Users and Groups. 8.5 Assigns the Print Permissions to Users and Groups as required. 8.6 Log on from the Client Computer and installs the Printer Client. 8.7 Installs the Printer Driver in the Client Computer if required. 8.8 Prints a Test Page from the Client using the Print Server. 8.9 Verifies the installation of Server and Client.

34

7


Server, Client, Print Server, Printer, Printer Driver and Utility.

8


8.1 Planed Resources for the Print Server along with the necessary Software and driver. 8.2 Tried using the Standard Drivers available in the Operating System if the Vendor supplied Software is not available. 8.3 Performed the Standard installation Procedure. 8.4 Completed the installation process and shared the Printer for Network Users and Groups. 8.5 Assigned the Print Permissions to Users and Groups as required. 8.6 Logged on from the Client Computer and installed the Printer Client. 8.7 Installed the Printer Driver in the Client Computer if required. 8.8 Printed a Test Page from the Client using the Print Server. 8.9 Verified the installation of Server and Client.

35

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

8

8.1

8.2 8.3

8.5

Knowledge of basic Printer Configuration. Basic concepts of Network Printing.

Knowledge of Printer Server and Queue. Working knowledge of Direct Network Printer

36


11

TASK TITLE: Installing and configuring print server and client

TASK NO : 8

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE?

8.1 Plan Resources for the Print Server along with the necessary Software and driver.

8.2 Try using the Standard Drivers available in the Operating System if the Vendor supplied Software is not available.

8.3 Perform the Standard installation Procedure. 8.4 Complete the installation process and share the Printer for Network

Users and Groups. 8.5 Assign the Print Permissions to Users and Groups as required. 8.6 Log on from the Client Computer and install the Printer Client. 8.7 Install the Printer Driver in the Client Computer if required. 8.8 Print a Test Page from the Client using the Print Server. 8.9 Verify the installation of Server and Client.

37

TASK SPECIFICATION

5 TASK NO : 9 TASK TITLE : Installing and configuring Email and Internet Client. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS 9.1 Checks the connectivity. 9.2 Prepares the Email and Internet Client Software for installation. 9.3 Plans to subscribe the service from the ISP. 9.4 Finds the name of SMTP and POP3 Servers to configure in the Mail Client Software and enters it in the appropriate options.

38

7

TASK PERFORMANCE REQUIREMENTS Client Computer, Modem, Modem Drivers, Operating System

8


9.1 Checked the connectivity. 9.2 Prepared the Email and Internet Client Software for installation. 9.3 Planed to subscribe the service from the ISP. 9.4 Found the name of SMTP and POP3 Servers to configure in the Mail Client Software and entered it in the

appropriate options.

39

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

9

9.1 9.2

Basic knowledge of Internet Technology. Basic knowledge of Network and Internet.

40


11

TASK TITLE: Installing and configuring Email and Internet Client.

TASK NO :9

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE?

9.5 Check the connectivity. 9.6 Prepare the Email and Internet Client Software for installation. 9.7 Plan to subscribe the service from the ISP. 9.8 Find the name of SMTP and POP3 Servers to configure in the

Mail Client Software and enter it in the appropriate options.

41

TASK SPECIFICATION

5 TASK NO : 10 TASK TITLE : Troubleshooting and repairing Network and its Devices. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS 10.1 Troubleshoots and repairs the Server Boot Process. 10.2 Troubleshoots and repairs logon problem which may be caused because of Cable, NIC, Hub and Driver files. 10.3 Troubleshoots permissions and solves it. 10.4 Troubleshoots Network Application and performance and solves accordingly. 10.5 Uses the Diagnostic Tools Utility for Self Test in the NIC.

42

7


A Network Systems with Servers, Clients, Cable, NIC, Hub and OS software, NIC Utility, etc

8


10.1 Troubleshooted and repaired the Server Boot Process. 10.2 Troubleshooted and repaired logon problem which may be caused because of Cable, NIC, Hub and Driver files. 10.3 Troubleshooted permissions and solved it. 10.4 Troubleshooted Network Application and performance and solved accordingly. 10.5 Used the Diagnostic Tools Utility for Self Test in the NIC.

43

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

10

10.1

10.2

10.3

10.4

Network Logon Processes

Basic functional knowledge of NIC, Hub, Switch, and Router.

Basic knowledge of Network Diagnostic Tools and Utility.

Basic knowledge of connecting two different Resources.

44


11

TASK TITLE: Troubleshooting Network and its Devices. TASK NO : 10

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE?

10.1 Troubleshoot and repair the Server Boot Process. 10.2 Troubleshoot and repair logon problem which may be caused

because of Cable, NIC, Hub and Driver files. 10.3 Troubleshoot permissions and solve it. 10.4 Troubleshoot Network Application and performance and

solve accordingly. 10.5 Use the Diagnostic Tools Utility for Self Test in the NIC.

45

TASK SPECIFICATION

5 TASK NO : 11 TASK TITLE : Installing Network Utility Software. JOB TITLE : Computer Network Technician, L-3

6

TASK ELEMENTS 11.1 Plans the Drives/Locations for Antivirus Software. 11.2 Plans the Antivirus Software as per requirement including update management. 11.3 Installs the Antivirus Software.

46

7


A Network Systems and Network supporting Antivirus Virus Utility.

8


11.1 Planed the Drives/Locations for Antivirus Software. 11.2 Planed the Antivirus Software as per requirement including update management. 11.3 Installed the Antivirus Software.

47

9 10

TASK TRAINING DATA

TASK No.

T.E. No.

TECHNICAL KNOWLEDGE


GRAPHIC INFORMATION

SAFETY AND HYGINE

11

11.1

11.2

Concept of Network based Applications Knowledge of Antivirus Software.

48


11

TASK TITLE: Installing Network Utility Software. TASK NO : 11

LOCATION OF TEST:

CANDIDATE'S NAME:

EVALUATORS NAME:

1. 2. 3.

12


STANDARD MET


DID THE CANDIDATE?

11.1 Plan the Drives/Locations for Antivirus Software. 11.2 Plan the Antivirus Software as per requirement including

update management. 11.3 Install the Antivirus Software.

Documents

Uploads_downloads_Computer Network Technician, OSS, L-3