Upgrade Gtmu With Btsm

7/16/2019 Upgrade Gtmu With Btsm

1/18

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

www.huawei.com

Internal

UPDATE THE NODEB

WITH M2000


2/18


Before starting work on site, you need to enter the

following command on the side of BSC

enterSET BTSAUTODLDACTINFO in the Command Input box, and then

click Assist. Set the parameters displayed below the Command Input box as follows:

Index Type: BYNAME(By Name) orBYID(By Index)

Auto Download Active Function Switch: OFF(OFF).

Then, click Exec.


3/18

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 3

Connect your laptop to the Ethernet

port of GTMU


4/18


Setting the IP Address of the Site Maintenance Terminal

PC

Procedure

To set the IP address of the PC, perform the following steps:

Choose Start> Setting > Control Panel.

Double-click Network Connections in the displayed Control Panel window.

Right-click Local Area Connection in the displayed dialog box.

Choose Properties from the shortcut menu. The Local Area Connection

Properties dialog box is displayed.

Select Internet Protocol (TCP/IP), and click Properties. The Internet Protocol

(TCP/IP) Properties dialog box is displayed.

Select Use the following IP address.

Enter the correct IP address, subnet mask. (192.168.0.71 or other in thesame segment)

Ensure that the IP address of the SMT PC is in the same network

segment as the IP addresses (192.168.0.72/255.255.255.0) of the BTS so

that a maintenance channel on the BTS side can be established.

Click OK to complete the settings.


5/18


PING THE BTS

On the command prompt of your computer, runping 192.168.0.72

If the information similar to that in the following example isreturned, the SMT PC and the BBU can communicate normally.

Pinging 192.168.0.72 with 32 bytes of data: Pinging 192.168.0.72with 32 bytes of data:

Reply from 192.168.0.72: bytes=32 time=1ms TTL=253




Ping statistics for 192.168.0.72: Packets: Sent = 4, Received = 4,Lost = 0 (0% loss), Approximate round trip times in milli-seconds:Minimum = 1ms, Maximum = 1ms, Average = 1ms


6/18


OPEN THE SMT


7/18HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

SETTING THE PARAMETERS TO

CONNECT TO THE BTS

To connect to the BTS with

the SMT:

1. Select Network Port

2. Input the ip 192.168.0.72

3. Click ok


8/18


GET THE MANAGEMENT RIGHTS


9/18


CLICK GET


10/18


CONFIRMATION OF THE MANAGEMENT RIGHTS

ACQUIRED


11/18


Checking the Software Versions of the BTS Boards

Click Board in the navigat ion tree, and then double-click

Board Managementin the Function pane on the right


12/18


In the displayed Board Managementwindow, right-click the GTMU and

then choose Board Informationfrom the shortcut menu.

The Board Information dialog box is displayed


13/18


Loading the GTMU Software

On the SMT, click Sitein the navigation tree, and then double-click Forced

Softw are Loadin the Funct ionpane on the right,


14/18


In the displayed Software Download dialog box, set the associated

parameters

File Name: Specify the path and name of the target software package required for the

upgrade.

Send Window Size: 200

Version: Type V100R009C00SP72 in the lower box.

File ID: Select GTMU_MAIN from thedrop-down list.

Click Start.

When the progress bar displays "100%" in the lower corner and the status bar

displays "Loading Software Successfully", click Close


15/18


Activating the GTMU Software

On the SMT, click Site in the navigation tree, and then double-click Software

Activation underFunction.


16/18


In the displayed dialog box, set the associated parameters as follows:

Version: Type V100R009C00SP72 in the lower box.

File ID: Select GTMU_MAIN from thedrop-down list.

Board No.: You are not required to set this parameter.

Click OK..

When the status bar displays "Activation is confirmed and the Site will

be reset in a few minutes", click Close.


17/18


Checking the Software Versions of the BTS Boards

Verify that the software is loaded correctly:

close and restart BTSM

Click Board in the navigation tree, and then double-click Board Management in the Function pane on theright

In the displayed Board Management window, right-click the GTMU and then choose Board Information fromthe shortcut menu.

The Board Information dialog box is displayed


18/18


Documents

Upgrade Gtmu With Btsm