Instructions for Updating Your Current Hardware Lock to Recognize STAAD.Pro 2003 (For Standalone Locks only) If you are an existing user of STAAD.Pro and are upgrading to STAAD.Pro 2003, your current lock will not work with STAAD.Pro 2003. You need to electronically update the lock to run STAAD.Pro 2003. STAAD.Pro can now automatically update the lock if your machine has an Internet connection, and if you can reach the website http://www.reiworld.com with your Web browser. The procedure for updating the lock is given below: If your machine is connected to the Internet: 1. Install STAAD.Pro 2003 2. Start the STAAD.Pr o 2003 program. Make sure that your hardware lock is attached to your m achine. 3. You shall receive a message notifying you that the current lock will not work with STAAD.P ro 2003. Click “Yes” when prompted with the question, “Are you connected to the Internet now?”. 4. The application will securely retrieve the necessar y informatio n from your existing lock and connect to the REI database system over the Internet. If successful, STAAD.Pro will automatically update your lock and launch STAAD.Pro. 5. If STAAD.Pro can connect to the Internet but cannot automatically update your lock (the information retrieved from your lock does not match the information in our database), it will display an error message. You should contact your local REI office with this message for technical assistance. If your machine is not connected to Internet: 1. Install STAAD.Pro 2003 2. Start the STAAD.Pr o 2003 program. Make sure that your hardware lock is attached to your m achine. 3. You shall receive a message notifying you that the current lock will not work with STAAD.P ro 2003. Click “No” when prompted with the question, “Are you connected to Internet now?”. The STAAD.Pro application will immediately close. 4. Go to Start | Programs | STAAD.Pro 2003 | License Administration to open the License Manager. 5. Go to Tools | G et Hardware Lock Key from the main menu. Write down the Hardware Lock Key displayed in the right-hand window pane. 6. Go to Tools | Get Serial Number from the main menu. Write down the program Serial Number displayed in the right-hand window pane. 7. On a computer that has In ternet access, go to http://www.reiworld.com/UpdateLock . Enter the Hardware Lock Key and the Serial Number (from Steps 5 and 6) when prompted. Alternatively, contact your nearest REI office over phone or email ( [email protected] ) with this information. 8. The Web site will try to generate a license file (.LDF file) as well as a unique password. If the application encounters an error, it will display an error message. If this happens, contact your nearest REI office for manual processing. 9. If the process is successful, the Web site will provide a link to download the license file (.LDF). Click on this link to save the license file (in any directory). Also, write down the password displayed on screen. 10. Take the .LDF file and the password to the machine where you have installed STAAD.P ro 2003. Make sure that the SAME lock is attached in the back of the machine. Copy the .LDF file (in any directory) to this machine. 11. Go to Start | Programs | STAAD.Pro 2003 | License Administration to open the License Manager once again. Go to Update | Update Lock from the main menu. Enter the location of the .LDF file in the first edit box. Enter the password you received in the second edit box. 12. A message box will confirm the lock update if the process was successful. You can now begin to use STAAD.Pro 2003. If you have any questions, please contact REI at [email protected] or call 1-800-FOR-RESE and ask for a STAAD.Pro Customer Service representative.

Update Stand Alone Lock

Download PDF Report

Upload
babu-sundararaman
View
219
Download
0

Embed Size (px)

Citation preview

8/19/2019 Update Stand Alone Lock

http://slidepdf.com/reader/full/update-stand-alone-lock 1/1

Instructions for Updating Your Current Hardware Lock to Recognize STAAD.Pro 2003(For Standalone Locks only)

If you are an existing user of STAAD.Pro and are upgrading to STAAD.Pro 2003, your current lock will not work with STAAD.Pro 2003. You need to electronically update the lock to run STAAD.Pro 2003.

STAAD.Pro can now automatically update the lock if your machine has an Internet connection, and if you can reachthe website http://www.reiworld.com with your Web browser. The procedure for updating the lock is given below:

If your machine is connected to the Internet:

1. Install STAAD.Pro 2003

2. Start the STAAD.Pro 2003 program. Make sure that your hardware lock is attached to your machine.

3. You shall receive a message notifying you that the current lock will not work with STAAD.Pro 2003. Click“Yes” when prompted with the question, “Are you connected to the Internet now?”.

4. The application will securely retrieve the necessary information from your existing lock and connect to theREI database system over the Internet. If successful, STAAD.Pro will automatically update your lock andlaunch STAAD.Pro.

5. If STAAD.Pro can connect to the Internet but cannot automatically update your lock (the informationretrieved from your lock does not match the information in our database), it will display an error message.You should contact your local REI office with this message for technical assistance.

If your machine is not connected to Internet:

1. Install STAAD.Pro 2003

2. Start the STAAD.Pro 2003 program. Make sure that your hardware lock is attached to your machine.

3. You shall receive a message notifying you that the current lock will not work with STAAD.Pro 2003. Click“No” when prompted with the question, “Are you connected to Internet now?”. The STAAD.Pro applicationwill immediately close.

4. Go to Start | Programs | STAAD.Pro 2003 | License Administration to open the License Manager.

5. Go to Tools | Get Hardware Lock Key from the main menu. Write down the Hardware Lock Key displayed inthe right-hand window pane.

6. Go to Tools | Get Serial Number from the main menu. Write down the program Serial Number displayed inthe right-hand window pane.

7. On a computer that has Internet access, go to http://www.reiworld.com/UpdateLock . Enter the HardwareLock Key and the Serial Number (from Steps 5 and 6) when prompted. Alternatively, contact your nearestREI office over phone or email ( [email protected]) with this information.

8. The Web site will try to generate a license file (.LDF file) as well as a unique password. If the applicationencounters an error, it will display an error message. If this happens, contact your nearest REI office formanual processing.

9. If the process is successful, the Web site will provide a link to download the license file (.LDF). Click on thislink to save the license file (in any directory). Also, write down the password displayed on screen.

10. Take the .LDF file and the password to the machine where you have installed STAAD.Pro 2003. Make surethat the SAME lock is attached in the back of the machine. Copy the .LDF file (in any directory) to thismachine.

11. Go to Start | Programs | STAAD.Pro 2003 | License Administration to open the License Manager once again.Go to Update | Update Lock from the main menu. Enter the location of the .LDF file in the first edit box.Enter the password you received in the second edit box.

12. A message box will confirm the lock update if the process was successful. You can now begin to useSTAAD.Pro 2003.

If you have any questions, please contact REI at [email protected] or call 1-800-FOR-RESE and ask for aSTAAD.Pro Customer Service rep resentative.