Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
CHICK-FIL-A Cut Sheet Manual
UNIVERSITY OF MARY HARDIN - BAYLOR
04/08/13
ITEM NO.: 116 QUANTITY: 1
DESCRIPTION: DUMP CART
MANUFACTURER: BKI
MODEL: WS-15STC
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 9.2 AMPS, 120V, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Item No. ___________________
BKI’s WS-15STC Warming Station with Cart
Agency Approvals:
Warming Station Model: WS-15ST
Compact Unit for Holding and Warming Fried Foods The Warming Station uses radiant heat
technology (top and lower heat) to extend
freshness for a variety of fried foods including
nuggets, fingers, fries, wedges, etc. Keep fried
foods moist and delicious and “presentation
ready” for a longer hold time. Features include
a rotating top that allows user to swivel the top
heat 90° for easier dumping and to eliminate
chance of burn. Also, a full-size, 2 ½” deep
steam table pan fits into the dump bin; this
along with the design of flat surfaces provides
easy cleaning of unit. Unit is designed to fit
into countertop opening (WS-15ST) or custom
designed cart (WS-15STC).
Standard Features: 10lb. Holding Capacity
Removable Parts and Flat Surfaces for
Easy Cleaning
BKI North America PO Box 80400 Simpsonville, SC 29680-0400 USA Telephone: (864) 963-3471 Toll Free: (800) 927-6887
BKI Europe Theale Technology Centre Station Road • Theale Reading • West Berkshire • RG7 4AA Telephone: 0870 9904242 • Fax: 0870 9904243
© BKI LI0045/032006 Specifications subject to change without notice. Printed in the U.S.A.
Warming Station (WS-15STC)
Equipment Dimensions: WS-15STC
Mechanical Specifications: Height Width Depth Weight WS-15ST 22.25” (56.5 mm) 15 3/8” (390.5 mm) 26 3/4” (679.5 mm) 58 lbs. (26.3 kg.) WS-15STC 55 3/8” (1406.5 mm) 18” (457.2 mm) 32.5” (825.5 mm) 82 lbs. (37.2 kg.)
Electrical Options: Model Volts Amps Breaker KW Wires Phase WS-15ST (C) 120 9.2 15 1.1 2 1
BKI North America PO Box 80400 Simpsonville, SC 29680-0400 USA Telephone: (864) 963-3471 Toll Free: (800) 927-6887
BKI Europe Theale Technology Centre Station Road • Theale Reading • West Berkshire • RG7 4AA Telephone: 0870 9904242 • Fax: 0870 9904243
© BKI LI0045/032006 Specifications subject to change without notice. Printed in the U.S.A.
ITEM NO.: 131 QUANTITY: 1
DESCRIPTION: SANDWICH MERCHANDISER (38’’) TWO TIER
MANUFACTURER: BKI
MODEL: 2TSM-3824
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 9.18 AMPS, 1.73 KW, 208V, 1 PHASE, PLUG PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: CORD LEFT PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Item No. _________________
Pictured: 2TSM-6224
Agency Approvals:
Sandwich Merchandiser Model: 2TSM-2624, 2TSM-3824,
2TSM-5024, 2TSM-6224
Countertop Sandwich Warmer with Ceramic Infrared Top Heat BKI’s Sandwich Merchandising equipment
offers you flexibility and extended holding
time. Designed with your unique
environment in mind, this unit is available in
a variety of lengths: 26, 38, 50, and 62 inch
models.
Standard Features: Ceramic infrared top heat Individual thermostatic controls Slot dividers
BKI North America PO Box 80400 Simpsonville, SC 29680-0400 USA Telephone: (864) 963-3471 Toll Free: (800) 927-6887
BKI Europe Theale Technology Centre Station Road • Theale Reading • West Berkshire • RG7 4AA Telephone: 0870 9904242 • Fax: 0870 9904243
© BKI LI0046/03-06 Specifications subject to change without notice. Printed in the U.S.A.
2TSM-2624, 2TSM-3824, 2TSM-5024, 2TSM-6224
Equipment Dimensions:
Mechanical Specifications: Dimension 2TSM-2624 2TSM-3824 2TSM-5024 2TSM-6224
Height 29 ¾” (444.5mm) 29 ¾” (444.5mm) 29 ¾” (444.5mm) 29 ¾” (444.5mm) Width 26” (660.4mm) 38” (965.2mm) 50” (1270.0mm) 62” (1574.8mm) Depth 24” (609.6mm) 24” (609.6mm) 24” (609.6mm) 24” (609.6mm)
Floor Space 4.33 sq.ft. (0.40 sq.m) 6.33 sq.ft. (0.59 sq.m) 8.33 sq.ft. (0.77 sq.m) 10.33 sq.ft. (0.96 sq.m)
Electrical Options: 2TSM-2624 2TSM-3824 2TSM-5024 2TSM-6224
Volts 120 120/208 120/208 120/208 Amps 9.13 9.18 9.66 13.02
Breaker 15 20 20 20 kW 1.090 1.730 1.830 2.460
Wires 2 3 3 3 Phase 1 1 1 1
Options
Direct sealed counter mount or 4” table legs Right or Left side mounted power cord Slot dividers
BKI North America PO Box 80400 Simpsonville, SC 29680-0400 USA Telephone: (864) 963-3471 Toll Free: (800) 927-6887
BKI Europe Theale Technology Centre Station Road • Theale Reading • West Berkshire • RG7 4AA Telephone: 0870 9904242 • Fax: 0870 9904243
© BKI LI0046/03-06 Specifications subject to change without notice. Printed in the U.S.A.
ITEM NO.: 150 QUANTITY: 1
DESCRIPTION: FRENCH FRY HOLDING UNIT
MANUFACTURER: BKI
MODEL: FW15-L PC#312008D
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 15 AMPS, 1.91 KW, 120V, 1 PHASE, PLUG, 5-20R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
ITEM NO.: 153 QUANTITY: 1
DESCRIPTION: HEAT LAMP
MANUFACTURER: BKI
MODEL: WS-15ST
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 9.7 AMPS, 120V, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Item No. ___________________
BKI’s WS-15STC Warming Station with Cart
Agency Approvals:
Warming Station Model: WS-15ST
Compact Unit for Holding and Warming Fried Foods The Warming Station uses radiant heat
technology (top and lower heat) to extend
freshness for a variety of fried foods including
nuggets, fingers, fries, wedges, etc. Keep fried
foods moist and delicious and “presentation
ready” for a longer hold time. Features include
a rotating top that allows user to swivel the top
heat 90° for easier dumping and to eliminate
chance of burn. Also, a full-size, 2 ½” deep
steam table pan fits into the dump bin; this
along with the design of flat surfaces provides
easy cleaning of unit. Unit is designed to fit
into countertop opening (WS-15ST) or custom
designed cart (WS-15STC).
Standard Features: 10lb. Holding Capacity
Removable Parts and Flat Surfaces for
Easy Cleaning
BKI North America PO Box 80400 Simpsonville, SC 29680-0400 USA Telephone: (864) 963-3471 Toll Free: (800) 927-6887
BKI Europe Theale Technology Centre Station Road • Theale Reading • West Berkshire • RG7 4AA Telephone: 0870 9904242 • Fax: 0870 9904243
© BKI LI0045/032006 Specifications subject to change without notice. Printed in the U.S.A.
Warming Station (WS-15STC)
Equipment Dimensions: WS-15STC
Mechanical Specifications: Height Width Depth Weight WS-15ST 22.25” (56.5 mm) 15 3/8” (390.5 mm) 26 3/4” (679.5 mm) 58 lbs. (26.3 kg.) WS-15STC 55 3/8” (1406.5 mm) 18” (457.2 mm) 32.5” (825.5 mm) 82 lbs. (37.2 kg.)
Electrical Options: Model Volts Amps Breaker KW Wires Phase WS-15ST (C) 120 9.2 15 1.1 2 1
BKI North America PO Box 80400 Simpsonville, SC 29680-0400 USA Telephone: (864) 963-3471 Toll Free: (800) 927-6887
BKI Europe Theale Technology Centre Station Road • Theale Reading • West Berkshire • RG7 4AA Telephone: 0870 9904242 • Fax: 0870 9904243
© BKI LI0045/032006 Specifications subject to change without notice. Printed in the U.S.A.
ITEM NO.: 165 QUANTITY: 2
DESCRIPTION: REFRIGERATOR (TWO SECTION)
MANUFACTURER: TRAULSEN
MODEL: RHT232WUT-FHS
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 10.4 AMPS, 120V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Project Quantity Item #
Model Specified: CSI Section 11400
SECTION1-1
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
Standard Product Features• R-Series: Stainless Steel Exterior & Interior• A-Series: Stainless Steel Exterior/Anodized Aluminum Interior• INTELA-TRAUL® Microprocessor Control System• Balanced, Self-Contained Refrigeration System Using R-134a• Scroll Blower Type Evaporator Fan• Biased Return Air Duct• Full or Half Length Stainless Steel Doors With Locks• Self-Closing Doors With Stay Open Feature At 120 Degrees• Guaranteed For Life Cam-Lift Hinges• Guaranteed For Life Horizontal Work Flow Door Handle• Standard Door Hinging: 132W = Right, 232W = Left/Right,
332W = Left/Right/Right (other hingings available)• Automatically Activated Incandescent Lights• Stainless Steel Breaker Caps• Three Chrome Plated Adjustable Shelves Per Section,
Supported On Shelf Pins (installed at the factory)• Automatic Non-Electric Condensate Evaporator• Magnetic Snap-In Door Gaskets• Gasket Protecting Metal Door Liner• Controllable Anti-Condensate Door Perimeter Heaters• Thermostatic Expansion Valve Metering Device• Stainless Steel One-Piece Louver Assembly• 9' Cord & Plug Attached• Set of Four (4) 6" High Adjustable Stainless Steel Legs• One Year Parts And Labor Warranty• Two Year Control Warranty (parts and labor)• Five Year Compressor Warranty
Options & Accessories• Stainless Steel Finished Back With Rear Louvers• Re-Hinging Feature For Door(s)• No. 1 Type Tray Slides To Accommodate either (1) 18" x 26"
or (2) 14" x 18" Sheet Pans, Adjustable To 2" O.C.• No. 2 Type Tray Slides To Accommodate (1) 18" x 26" Sheet
Pans, Adjustable To 2" O.C.• No. 3 Type Tray Slides To Accommodate (2) 12" x 20" Steam
Table Pans, Adjustable To 2" O.C.• No. 4 Type Tray Slides To Accommodate (1) 18" x 26" Sheet
Pans (chrome rod type, equips 1/2 section)• Universal Type Tray Slides To Accommodate Either (1)
18" x 26" or (2) 14" x 18" Sheet Pans, or (2) 12" x 20" SteamTable Pans, Adjustable To 4" O.C.
• Additional Chrome Plated Shelves• Locking Hasps (padlocks supplied by others)• Export 220/50/1 Voltage• 208/115/60/1 Voltage In Lieu Of Standard 115/60/1• Stainless Steel Shelves In Lieu of Standard Chrome Plated• Kool Klad Exterior Laminate Decor• Set of Four (4) 6" High Casters In Lieu of Legs• Set of Four (4) 4-7/16" High Casters In Lieu of Legs• 4-1/2" High Stainless Steel Base In Lieu of Legs• 6" High Stainless Steel Kickplate (for use with standard legs)• Prison/Correctional Facilities Options• Remote Applications (see spec sheet 12-2 for more details)• Clear Glass Door(s) In Place Of One Or More Solid Door(s)• Modification For Use As A Dough Retarder• Two Year Service/Labor Warranty Available
"W-Width" Reach-In Refrigerator Models/Self-Contained
Listed by Underwriters Laboratories Inc., toU.S. and Canadian safety standards andListed by NSF International. Approval: ___________________________________
Model RHT132WUT-FHS
One, Two & Three Section Models, 32" Deep1-Section Full Length Door Model RHT132WUT-FHS2-Section Full Length Door Model RHT232WUT-FHS3-Section Full Length Door Model RHT332WUT-FHS1-Section Half Length Door Model RHT132WUT-HHS2-Section Half Length Door Model RHT232WUT-HHS3-Section Half Length Door Model RHT332WUT-HHS
RSERIES
ASERIES
1-Section Full Length Door Model AHT132WUT-FHS2-Section Full Length Door Model AHT232WUT-FHS3-Section Full Length Door Model AHT332WUT-FHS1-Section Half Length Door Model AHT132WUT-HHS2-Section Half Length Door Model AHT232WUT-HHS3-Section Half Length Door Model AHT332WUT-HHS
(shown with optional casters)
INTELA-TRAUL®
Equipped!
Stainless Exterior& Interior
Stainless Exterior,Anodized
Aluminum Interior
The R & A Series represent Traulsen's Top-of-the-Line product offering. The“W-Width” reach-in refrigerator models are all designed to offermaximum interior storage capacity. Each is supplied standard with such highquality features as balanced refrigeration systems, microprocessor controls,communications ability and stainless steel exteriors. Additionally, they offerthe widest range of optional accessories to choose from, and can bespecified for use with many different applications, including: Foodservice,Correctional, Institutional, Export, etc.
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
SECTION1-1
DIMENSIONAL DATA R/AHT132WUT R/AHT232WUT R/AHT332WUT
Net capacity cu. ft. 24.2 (686 cu l) 51.6 (1462 cu l) 79.0 (2238 cu l)
Length - overall in. 297⁄8 (75.9 cm) 58 (147.3 cm) 861⁄8 (218.8 cm)
Depth - overall in. 35 (88.8 cm) 35 (88.8 cm) 35 (88.8 cm)
Depth - less handle in. 333⁄4 (84.4 cm) 333⁄4 (84.4 cm) 333⁄4 (84.4 cm)
Depth - over body in. 32 (81.3 cm) 32 (81.3 cm) 32 (81.3 cm)
Depth - door open 90° in. 5711⁄16 (146.5 cm) 5711⁄16 (146.5 cm) 5711⁄16 (146.5 cm)
Clear door width in. 211⁄8 (53.6 cm) 211⁄8 (53.6 cm) 211⁄8 (53.6 cm)
Clear half-door height in. 271⁄2 (69.9 cm) 271⁄2 (69.9 cm) 271⁄2 (69.9 cm)
Clear full-door height in. 575⁄8 (146.3 cm) 575⁄8 (146.3 cm) 575⁄8 (146.3 cm)
Height - overall on 6" legs 831⁄4 (211.5 cm) 831⁄4 (211.5 cm) 831⁄4 (211.5 cm)
No. Standard Shelves 3 6 9
Shelf area sq. ft.1 18.8 (1.75 sq m) 37.6 (3.49 sq m) 56.4 (5.23 sq m)
ELECTRICAL DATA
Voltage 115/60/1 115/60/1 115/60/1
Feed wires with Ground 3 3 3
Full load amperes 8.0 10.4 10.9
REFRIGERATION DATA
Refrigerant R-134a R-134a R-134a
BTU/HR H.P.2 2220 (1⁄3 HP) 4200 (1⁄2 HP) 4200 (1⁄2 HP)
SHIPPING DATA3
Length - crated in. 35 (89 cm) 63 (160 cm) 91 (231 cm)
Depth - crated in. 43 (109 cm) 43 (109 cm) 43 (109 cm)
Height - crated in. 831⁄2 (212 cm) 831⁄2 (212 cm) 831⁄2 (212 cm)
Volume - crated cu. ft. 71 (2011 cu l) 131 (3711 cu l) 189 (5354 cu l)
RHT Net Wt. lbs. 380 (172 kg) 630 (286 kg) 880 (399 kg)
RHT Gross Wt. lbs. 470 (213 kg) 770 (349 kg) 1060 (481 kg)
AHT Net Wt. lbs. 330 (150 kg) 550 (249 kg) 760 (345 kg)
AHT Gross Wt. lbs. 420 (191 kg) 690 (313 kg) 940 (426 kg)
NOTE: When ordering please specify: Voltage, Hinging, Door Size, Options and anyadditional warranties.
Continued product development may necessitate specification changes without notice.Part No. TR35755 (revised 4/04)
Construction, Hardware and InsulationCabinet exterior front, one piece sides, louver assembly and doors are constructedof 20 gauge stainless steel with #4 finish. Cabinet interior and door liners areconstructed of stainless steel (anodized aluminum in the A-Series). The exterior cabinettop, back and bottom are constructed of heavy gauge aluminized steel. A set of four(4) adjustable 6" high stainless steel legs are included.
Doors are equipped with a gasket protecting metal door pan, removable plugcylinder locks and guaranteed for life cam-lift, gravity action, self-closing metal, glidehinges with stay open feature at 120 degrees. Hinges include a concealed switch toautomatically activate the interior incandescent lighting. Guaranteed for life, workflow door handles are mounted horizontally over recess in door which limitsprotrusion from door face into aisleways. Doors have seamless, polished metalcorners.
Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal.Anti condensate heaters are located behind each door opening.
Both the cabinet and door(s) are insulated with an average of 2" thick high density,non-CFC, foamed in place polyurethane.
Refrigeration SystemA top mounted, self-contained, balanced refrigeration system using R-134arefrigerant is conveniently located behind the one piece louver assembly. It featuresan easy to clean front facing condenser, thermostatic expansion valve, air-cooledhermetic compressor, plenum effect blower coil, large, high humidity evaporator coillocated outside the food zone and a top mounted non-electric condensateevaporator. Biased return air duct protects against introduction of warm kitchen air,promoting even temperature maintenance and efficient operation. A 9' cord andplug is provided. Standard operating temperature is 34 to 38°F.
ControllerThe easy to use water resistant INTELA-TRAUL® microprocessor control system issupplied standard. Unit is NAFEM Data Protocol communication (NDP) ready.Optional hardware required to be NDP compliant. Third party software required fornetwork connection. It includes a 3-Digit LED Display, Fahrenheit or CelsiusTemperature Scale Display Capability, and an RS485 data port. In addition itincludes audio/visual alarms for: Hi/Lo Cabinet Temperature, Door Open, CleanCondenser, Evaporator Coil and Discharge Line Sensor Failures, and Power SupplyInterruption.
InteriorStandard interior arrangements include three (3) chrome plated wire shelves persection, mounted on shelf pins. Shelves are full-width, and do not have any largegaps between them requiring the use of "bridge" or "junior shelves." Recommendedload limit per shelf should not exceed 225 lbs. Optional tray slides may bepurchased in combination with, or in lieu of these. Both standard and optionalinterior arrangements are completely installed at the factory.
WarrantiesBoth a one year parts and labor warranty and a five year compressor warranty (self-contained models only) are provided standard. An optional 2nd year extended partsand labor warranty is also available. In addition the INTELA-TRAUL® control iswarranted by a two year parts and labor warranty.
Specifications
NOTESNOTE: Figures in parentheses reflect metric equivalents.1= Area of standard shelf compliment only, does not include storage area of additional shelves or available
on cabinet bottom.2= Based on a 90 degree F ambient and 20 degree F evaporator.3= For approximate remote weights deduct 40 lbs. from respective net or gross weight. For other information
on remote models, please refer to spec sheet 12-2.
Plan - R/AHT132WUT
Elevation -R/AHT132WUT
Section - All Models
Plan - R/AHT232WUT
Elevation -R/AHT232WUT
Plan - R/AHT332WUT
Elevation -R/AHT332WUT
Equipped With One NEMA 5-15 P Plug
NOTE: Full load amps and plug style may vary dependingon electrical options chosen and condensing unit employed.
ITEM NO.: 166 QUANTITY: 1
DESCRIPTION: SALAD PREP TABLE (66”)
MANUFACTURER: TRAULSEN
MODEL: TS066HT-ZCF03
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 9 AMPS, 115V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
Pizza/Salad/Sandwich Prep TablesSelf-Contained
Standard Product Features• "All-Day" Temperature Performance To NSF7 Test Requirements• High Quality Stainless Steel Exterior/Interior Construction• INTELA-TRAUL® Patented Microprocessor Control• 115/60/1V Self-Contained System Using R-404a Refrigerant• Stainless Steel Insulated Lift-Up Rail Covers with Two Convenient Open Positions• Accommodates Industry Standard Full, Half, Third & 6" Deep
Size Pans Without The Use Of Adapter Bars (pans provided by others)• Accommodates Sixth & Ninth Size Pans With The Use Of
Adapter Bars (pans & bars provided by others)• Stainless Steel Field Re-Hingeable Door(s), With Locks• Self-Closing Door(s) with Stay Open Feature • Metal Door Handle with Gasket Guard• Magnetic Snap-In Door Gaskets For Tight Door Seal• Gasket-Protecting Stainless Steel Door Liner• Two (2) Shelves Per Door, Mounted On Shelf Pins (factory installed)• Energy Saving Non-Electric Automatic Condensate Evaporator• Hot Gas Evaporator Defrost• Thermostatic Expansion Valve Metering Device• Large Interior Storage Capacity & Spacious Work Surface• 6" Caster On Adjustable Channel Mounting System• Side, Front & Rear Access Panel For Ease of Service & Maintenance• 9' Cord & Plug Attached• One Year Service Labor & 5 Year Compressor Warranty• Two Year Control Warranty (parts and Labor)• Three Year Drawer Parts Warranty
Options & Accessories• Stainless Steel Finished Back• Additional Standard Shelves • Stainless Steel Shelves In Lieu of Standard Shelves• Set of 3-1/2" & 4-5/8"Casters or set of 6" Legs • Optional Installed Casters• BI-FOLD or LIFT-OFF Rail Covers• Full Length White Plastic Cutting Board, 1/2" H x 18" D • Full Length Composite Cutting Board, 1/2" H x 18" D• Counter Top Garnish Rack• 16 Gauge Stainless Steel Single Over shelf (16-1/4" deep)• Adapter Bar Package (allows the use of fractional equivalent
size pans)• Rail Mount Scale Stand• Rail Mount Ambient Pan Holder• Ticket Rail• Two (2) Drawers In Lieu Of One Or More Doors (accommodates 6" deep pans)• Three (3) Drawers In Lieu Of One Or More Doors (accommodates 4" deep pans)• No. 1 Type Tray Slides To Accommodate either (1) 18" x 26"
or (2) 14" x 18" Sheet Pans, Adj. to 2" OC• Universal Type Tray Slides To Accommodate either (1) 18" x 26" or (2) 12" x 20" or (2) 14" x 18" Sheet Pans, Adj. to
4" OC• Export 220/50/1 Voltage (consult factory)• NAFEM Data Protocol Gateway Package• Two Year Service/Labor Warranty
Approval: __________________________________
Model TS072HT
48", 66", 72" & 90" Wide Models 48" Long Model for 6 x 1/3 Pans TS048HT66" Long Model for 9 x 1/3 Pans TS066HT72" Long Model for 10 x 1/3 Pans TS072HT 90" Long Model for 12 x 1/3 Pans TS090HT
TSSERIES
The #1 complaint about prep tables is pans not being kept cold enough. This can lead to unnecessary food waste, Health Department citations, or even food safety issues. Other problems include frequently frozen product, and the labor required everyday to clean the inevitable ice and water made by traditional cold wall types. If you’ve experienced any of these problems before, then Traulsen's easy to clean prep table (with drain) is what you've been looking for. Also, Traulsen prep table's TempAssure air flow system circulates cold air around and underneath the pans, as well as lofting a protective blanket over the food surface, effectively insulating it from warm kitchen air. For you this means...
✔"All-Day" Temperature Performance To NSF7 Test Requirements ✔Doesn't Freeze Product ✔No Dried Product ✔No Ice To Clean Up
TempAssure air flow system ensures pans are held cold, making them ideal for preparing pizzas, sandwiches, bagels, gyros, burgers, salads, tacos/bur-ritos, sushi, etc. or nearly anything requiring a ready supply of cold ingredients and/or condiments. Traulsen's TS Series prep tables provide the answer to the all too common open top pan dilemma.
✔Holds 6" Deep Pans✔Pans Held Completely Level✔No Pan Stirring
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
Section View - All Models
Plan & Elevation View - TS048HT Plan & Elevation View - TS066HT
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
Plan & Elevation View - TS072HT Plan & Elevation View - TS090HT
Section View - All Models
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
NOTE: When ordering please specify: Voltage, Hinging, Options and any additional warranties. Continued product development may necessitate specification changes without notice. Part No. TR35920 (revised 10/10)
REFRIGERATION SYSTEMThe self-contained refrigeration system cools the cabinet interior, as well as the raised ingredient rail through use of an exclusive TempAssure airflow ducting system which creates a layer of cold air over the pans, as well as all sides and bottom of the pans. This system distributes cold air from top to bottom, keeping the pans cold without freezing product and allows for "all-day" temperature performance to NSF7 test requirements. The condensing unit utilizes a hermetically sealed compressor, which is easily accessible behind the louvers. A 9' cord and plug is supplied standard. Standard interior cabinet operating temperature is 34 to 38°F.WARRANTIESBoth a one year parts and labor warranty and a five year compressor war-ranty are provided standard. Three Year drawer parts warranty. An optional 2nd year extended parts and labor warranty is also available.
CONSTRUCTION, HARDWARE AND INSULATIONUnit exterior top and front sides are constructed of stainless steel, back and bottom is constructed of galvanized steel. Cabinet interior is constructed of stainless steel. Unit is insulated with an average 2" insulation on the top, bottom and all sides.The 12" wide raised ingredient rail is designed to accommodate standard full, half or third size pans (pans supplied by others). Other size pans require use of adapter bars (pans and bars supplied by others). Accom-modates 6" deep pans. Stainless steel insulated lift-up rail cover, with two convenient open positions.Doors are equipped with self-closing hinges and metal door handle with gasket guard. Each includes an easily removable for cleaning, vinyl mag-netic door gasket which assures a tight door seal. INTERIOR ARRANGEMENTS & SUPPORTSUnit includes two (2) shelves per door, mounted on shelf pins. Cabinet is mounted on a set of 6" high heavy-duty casters.
Specifications
Equipped With One NEMA 5-15P Plug
NOTESNOTE: Figures in parentheses reflect metric equivalents.1=TS072HT consists of two drawer pan configurations, left hinged door has a side by side pan configuration & right hinged door has a front to back pan configuration (applies to drawer options only)2= Depth - Overall includes 2" removal stand off bracket located on back of unit. See drawings for detailed dimensions.3=Area of standard shelf compliment only, does not include storage area of additional shelves or area available on cabinet bottom.4=Based on a 90 degree F ambient and 10 degree F evaporator.
DIMENSIONAL DATA TS048HT TS066HT TS072HT TS090HT
Net Capacity cu. ft. 9.5 15.7 17.9 24.4Number of Pans (third size) 6 9 10 12Drawer Option1 Pan Configurations Front to Back Side by Side See Note 1 Side by SideLength - Overall in. 48 (121.9 cm) 66 (167.6 cm) 72 (182.9 cm) 90 (228,6 cm)Depth - Overall in.2 36 (91.4 cm) 36(91.4 cm) 36(91.4 cm) 36(91.4 cm)Clear Door Width in. 23 18.7 23 & 18.7 18.7Clear Door Height in. 20.5 20.5 20.5 20.5Number of Doors 1 2 2 3Standard Door Hinging RH LH/RH LH/RH LH/LH/RH
Number of Shelves 2 4 4 6Shelf Area sq. ft.3 9.2 14.8 16.6 22.2Work Surface Height in. 35-9/16 (90.3 cm) 35-9/16 (90.3 cm) 35-9/16 (90.3 cm) 35-9/16 (90.3 cm)Height - Overall in. 48-3/8 (122.9 cm) 48-3/8 (122.9 cm) 48-3/8 (122.9 cm) 48-3/8 (122.9 cm)ELECTRICAL DATA
Voltage 115/60/1 115/60/1 115/60/1 115/60/1Full Load Amperes 9.8 9.0 9.0 9.0NEMA Plug 5-15P 5-15P 5-15P 5-15PREFRIGERATION DATA
Refrigerant R-404a R-404a R-404a R-404aBTU4 3300 3870 3870 3870Compressor HP 1/2 1/2 1/2 1/2
Listed by Underwriters Laboratories Inc. and the NSF International in accordance with ANSI/NSF7.
ITEM NO.: 171 QUANTITY: 1
DESCRIPTION: CHICK-FIL-A EXPRESS SIGNAGE (20”)
MANUFACTURER: CLAYTON SIGNS
MODEL: CUSTOM
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 120V, 1 PHASE, 10 AMPS, DIRECT PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
PER DRAWING
PER
DRA
WIN
G
ITEM NO.: 212 QUANTITY: 1
DESCRIPTION: TEA BREWER
MANUFACTURER: WILBUR CURTIS
MODEL: TCTT10040 G3
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 14.2 AMPS, 120V, PLUG, NEMA 5-15R 3/8 FW PLUMBING: 48” A.F.F. VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
TCTS(Shown with optional TCO dispenser)
PTT3(With standard Tea Toter Dispenser)
Sweet Tea Control Module
G3 DIGITAL ICED TEA BREWING SYSTEMS
MODELS: PTT310, TCTS10, TCTT10, TCTS10 SWEET TEA
•• GG33 DDiiggiittaall CCoonnttrrooll MMoodduullee – Provides precisecontrol for gourmet fine tuning with pulse-brewing,delay, and all critical brewing functions.
•• GG33 EEnnhhaanncceedd TTeeaa FFllaavvoorr && CCllaarriittyy – With digitalaccuracy, two separate precision valves provideunsurpassed control over concentrate brewingand dilution cycles.
•• ““FFaasstt BBrreeww”” OOppttiioonn – Program selectable.Shortens brew time by allowing concentrate anddilution cycles to run at the same time.
•• ““DDuuaall BBaattcchh”” OOppttiioonn -- Overlay available (OrderSeparately).
•• IInnttuuiittiivvee SSccrroollll--TThhrroouugghh PPrreecciissiioonn PPrrooggrraammmmiinngg– Large, brightly lighted display communicatesfunctions at a glance. Easily adjust time, volume,temperature, brew functions and more.
•• TTwwoo FFaaccttoorryy SSeett RReecciippeess...... RReegguullaarr aanndd TTrrooppiiccaall– For out-of-the-box operation.
•• OOnn--BBooaarrdd SSeellff DDiiaaggnnoossttiiccss – G3 continuallysenses proper brewing operation. A ServicePhone Number and error code will be displayed inthe rare event technical assistance is required...reducing downtime.
•• CCuurrttiiss’’ EExxcclluussiivvee GG33 33--YYeeaarr WWaarrrraannttyy – 3 yearsof protection on the digital control components.
•• CCoolldd WWaatteerr BBrreeww LLoocckk--OOuutt – Prevents brewingwhen water temperature is below set level.
•• SSttaannddaarrdd 112200VVAACC OOppeerraattiioonn – Makes installationquick and simple.
•• CCoolloorrffuull ““IIcceedd TTeeaa”” MMeerrcchhaannddiissiinngg GGrraapphhiiccss
•• ““SSwweeeett TTeeaa”” BBrreewweerr -- Complete with electricpump. Program selectable for regular or sweet tea.
The new Curtis G3 Tea Brewing Systems – incredible tea flavor, simple operation, reduced maintenance.
At the center of the Curtis G3 Tea Brewing Systems is its unique UniversalControl Module. The G3’s oversized LCD display and simple interface makes“scroll-through” programming incredibly easy. Of course, there’s no need toadjust the system, as Curtis’ pre-programmed factory settings deliver ideal resultsright out of the carton. Simply add bulk leaves or flow-thru filter packs andpress the brew button for gallons of cool, flavorful iced tea in just minutes.
Curtis G3 Systems include a host of new features designed to optimize teaquality including... digital temperature and brew-by-volume control, PM alerts,cold water brew lock-out, and much more. The result is perfect tea flavor andclarity, which keeps customers – and profits – returning.
Select from the low-profile Polaris PTT3 with movable “TeaToter” dispenser or theTCTS, TCTT or Sweet Tea for direct-to-dispenser high-volume brewing.
FEATURES AT A GLANCE
ITEM NO
PROJECT
DATE
Revolutionary DesignTWO Ultra-Precision Inlet Valves
and Water Level Sensor System provideunsurpassed tea flavor.
WILBUR CURTIS COMPANY, INC.6913 Acco Street, Montebello, CA 90640-5403Telephone: 800-421-6150 · 323-837-2300Fax: 323-837-2406www.wilburcurtis.com
©2007 Wilbur Curtis Company, Inc. Printed in U.S.A · JUN/08 – 12625 F-3360 rev.E
TCTS10TCTT10Sweet Tea(Dispenser Not Included)
PTT310(TCO 308 DispenserIncluded)
Fits Brewer Model PTT310 PTT310 TCTS10/TCTT10 TCTS10/TCTT10Capacity 3 Gallons n/a 4 Gallons 3.5 GallonsFaucet Clearance n/a n/a 9.875” 8.125”Diameter/Dimensions 9”h x 11.125”w x 13.5”d 10”h x 14”w x 14”d 21”h x 11.125”w x 15”d 9.375” diameterOverall Height 13.5” 14” 21.75” 22.75”Shipping Weight 5 lbs. 8 lbs. 12 lbs. 8.25 lbs.Cube (cu.ft) 1.8 1.1 3.7 1.3
Specifications TCTS10 TCTT10 PTT310
Iced Tea Dispensers TCO-308 (Oval) TCO-RS (Stand) TCO-421 (Oval) TC-3H (Round)
Finished Brew Capacity 3 to 5 Gallons 3 to 5 Gallons 3 Gallons Dimensions (HxWxD) 34” x 10.125” x 20.75” 38.25” x 10.125” x 20.75” 29” x 11.125” x 20.875”Voltage 120VAC/60Hz 120VAC/60Hz 120VAC/60Hz Power Requirements 1700W/14.2A 1700W/14.2A 1700W/14.2A Cord & Plug 6 ft/NEMA 5-15P 6 ft/NEMA 5-15P 6 ft/NEMA 5-15P Water Inlet 1/4” Flare 1/4” Flare 1/4” FlareShipping Weight 38 lbs. 38 lbs. 46 lbs.Cube (cu.ft) 9.7 9.7 7.5
9”(22.9 cm)
TCTT38.25”
(97.2 cm)
TCTS34”
(86.4 cm)
1.125” (2.9 cm)
10.125” (25.7 cm)
TCTT26.625”(67.6 cm)
TCTS22.375”(56.8 cm)
TCTT26.25”
(66.7 cm)
TCTS22.125”(56.2 cm)
13.5”(34.3 cm)
20.75”(52.7 cm)
11.5”(29.2 cm)
1/4” FLARE WATERCONNECTION
16.5”(41.9 cm)
1”(2.5 cm)
2.875” (7.3 cm)
5.25”(13.3 cm)
13.5”
22.5”
ITEM NO.: 216 QUANTITY: 1
DESCRIPTION: COFFEE BREWER
MANUFACTURER: WILBUR CURTIS
MODEL: TP2S10A3140
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 20 AMPS, 4 KW, 220V, 1 PHASE, PLUG, NEMA L14-30R 3/8 FW PLUMBING: 48” A.F.F. VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
ITEM NO.: 220 QUANTITY: 1
DESCRIPTION: LEMONADE DISPENSER
MANUFACTURER: CLELAND
MODEL: S-2
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 4 AMPS, 115V, 1 PHASE, PLUG PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
ITEM NO.: 224 QUANTITY: 1
DESCRIPTION: ICE CREAM MACHINE (AIR COOLED)
MANUFACTURER: TAYLOR
MODEL: 751
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 208V, 3 PHASE, PLUG PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
ITEM NO.: 228 QUANTITY: 1
DESCRIPTION: UNDERCOUNTER REFRIGERATOR (48”)
MANUFACTURER: HOBART/TRAULSEN
MODEL: UHT48
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 5.7 AMPS, 0.48 KW, 1/3 HP, 115V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: NO TOP W/ CASTERS PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Project Quantity Item #
Model Specified: CSI Section 11400
SECTION
9-1
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
Standard Product Features• Stainless Steel Exterior Top, Sides & Door(s)
• Anodized Aluminum Interior
• Front Breathing Self-Contained Refrigeration System
• Environmentally Friendly R-134a Refrigerant
• Self-Closing Stainless Steel Door(s) With Stay Open Feature
At 105 Degrees
• Horizontal Work Flow Door Handle
• Anodized Aluminum Interior Door Liner
• Standard Door Hinging: UHT27 = Left, UHT48 = Left/Right,
UHT60 = Left/Right (other hingings available)
• Interior Mounted Thermometer
• Two (2) Powder Coated Shelves Per Door, Mounted On
Pilasters
• Automatic Non-Electric Condensate Evaporator
• Magnetic Snap-In Door Gasket(s)
• 8' Cord & Plug Attached
• Set of Four (4) 6" High Adjustable Legs (6 for model UHT60)
• One Year Parts And Labor Warranty
• Five Year Compressor Warranty
Options & Accessories• 22 Gauge Stainless Steel Worktop With 4" High Backsplash
• Stainless Steel Finished Back
• Additional Powder Coated Shelves
• 6" Overall Height Casters (for use in lieu of legs)
• 4" Overall Height Casters (for use in lieu of legs)
• 3-1/2" Overall Height Casters (for use in lieu of legs)
• 2-1/2" Overall Height Casters (for use in lieu of legs, 27"models only)
• Two Year Service/Labor Warranty Available
Compact Undercounter Refrigerators/Self-Contained
Listed by Underwriters Laboratories Inc., to
U.S. and Canadian safety standards and
Listed by NSF International. Approval: ___________________________________
Left To Right Models UHT60, UHT48 & UHT27
27", 48" & 60" Wide Models
27" Wide One Door Model UHT27
48" Wide Two Door Model UHT48
60" Wide Two Door Model UHT60UHT
SERIES
(shown with optional casters)
Stainless Exterior,
Anodized
Aluminum Interior
Finally there is a compact undercounter product worthy of the Traulsen name.
Their rugged construction and high quality components make these units
capable of standing up to the demanding environment of any foodservice
kitchen. Each unit is built with a high quality stainless steel exterior and
durable anodized aluminum interior.
They are also designed for high performance, providing accurate
temperature maintenance. Fresh, safe food is assured, even under the
most demanding conditions.
Their front breathing design allows for "zero-clearance" installation. As a
result they can be placed right up against the backwall and alongside other
kitchen equipment, saving valuable floor space. Additionally, they offer a
wide range of optional accessories to choose from, and are ideal for use with
many different type applications.
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
SECTION
9-1
Plan - UHT27
Plan - UHT48
Elevation - UHT27
Elevation - UHT48
Project Quantity Item #
Model Specified: CSI Section 11400
SECTION
9-1
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
Plan - UHT60
Elevation - UHT60
Section - 27" & 60" Models Section - 48" Models
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
SECTION
9-1
DIMENSIONAL DATA UHT27 UHT48 UHT60
Net capacity cu. ft. 7.1 13.1 16.7
Length - overall in. 27 48 60
Depth - overall in. 307⁄8 307⁄8 307⁄8
Depth - with door open 90° 545⁄8 50 543⁄8
Clear door height in. 241⁄8 241⁄8 241⁄8
Clear door width in. 223⁄4 181⁄4 223⁄4
Height - overall on 6" legs in. 351⁄2 351⁄2 351⁄2
Number of shelves - total 2 4 4
Shelf area sq. ft. 4.88 10.3 13.2
ELECTRICAL DATA
Voltage 115/60/1 115/60/1 115/60/1
Full Load Amperes 3.3 5.7 5.7
Wattage 225 480 480
REFRIGERATION DATA
Refrigerant R-134a R-134a R-134a
BTU/HR - H.P.1 889 (1⁄6 HP) 1869 (1⁄4 HP) 1869 (1⁄4 HP)
SHIPPING DATA
Length - Crated in. 44 631⁄2 751⁄2
Depth - Crated in. 441⁄4 441⁄4 441⁄4
Height - Crated in. 463⁄4 463⁄4 463⁄4
Volume - Crated cu. ft. 53 76 90
Net Wt. lbs. 250 265 355
Gross Wt. lbs. 275 290 380
NOTE: When ordering please specify: Voltage, Hinging, Optional Accessories and any
additional warranties.
Continued product development may necessitate specification changes without notice.
Part No. TR35819 (revised 3/06)
Construction, Hardware and Insulation
Cabinet exterior front, one piece sides, louver assembly and doors are constructed
of 22 gauge stainless steel. Cabinet interior and door liners are constructed of
anodized aluminum. The exterior cabinet back and bottom are constructed of
galvanized steel.
A stainless steel door with a recessed work-flow handle and anodized aluminum liner
is provided. The door self closes at less than 90 degrees and also includes a stay
open feature at 105 degrees. Easily removable for cleaning, vinyl magnetic door
gasket assures tight door seal.
Both the cabinet and door(s) are insulated with an average of 2" thick high density,
non-CFC, foamed in place polyurethane.
Refrigeration System
A balanced, rear mounted, front breathing, self-contained refrigeration system using
R-134a refrigerant is provided. It features a capillary tube metering device, air-cooled
hermetic compressor, a forced air evaporator coil and a non-electric condensate
evaporator. An 8' cord and plug is provided. Standard operating temperature is 34 to
38°F.
Interior
Standard interior arrangements include two (2) powder coated wire shelves per door,
mounted on pilasters. These are adjustable in 1/2" increments, allowing for a mini-
mum of 1-1/2" spacing between shelves.
Warranties
Both a one year parts and labor warranty and a five year compressor warranty (self-
contained models only) are provided standard. An optional 2nd year extended parts
and labor warranty is also available.
Specifications
NOTE: Freight charges are FOB destination for dock to dock
delivery within the continental USA. Liftgate delivery
charges are additional. For inside delivery charges, please
consult factory.
Equipped With One NEMA 5-15 P Plug
NOTES
1= Based on a 90 degree F ambient and 20 degree F evaporator.
ITEM NO.: 229 QUANTITY: 1
DESCRIPTION: UNDERCOUNTER REFRIGERATOR 27”
MANUFACTURER: HOBART/TRAULSEN
MODEL: UHT27-ZCF
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 3.3 AMPS, 0.23 KW, 1/6 HP, 115V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: NO BSWO OR TOP HGD RIGHT PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Project Quantity Item #
Model Specified: CSI Section 11400
SECTION
9-1
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
Standard Product Features• Stainless Steel Exterior Top, Sides & Door(s)
• Anodized Aluminum Interior
• Front Breathing Self-Contained Refrigeration System
• Environmentally Friendly R-134a Refrigerant
• Self-Closing Stainless Steel Door(s) With Stay Open Feature
At 105 Degrees
• Horizontal Work Flow Door Handle
• Anodized Aluminum Interior Door Liner
• Standard Door Hinging: UHT27 = Left, UHT48 = Left/Right,
UHT60 = Left/Right (other hingings available)
• Interior Mounted Thermometer
• Two (2) Powder Coated Shelves Per Door, Mounted On
Pilasters
• Automatic Non-Electric Condensate Evaporator
• Magnetic Snap-In Door Gasket(s)
• 8' Cord & Plug Attached
• Set of Four (4) 6" High Adjustable Legs (6 for model UHT60)
• One Year Parts And Labor Warranty
• Five Year Compressor Warranty
Options & Accessories• 22 Gauge Stainless Steel Worktop With 4" High Backsplash
• Stainless Steel Finished Back
• Additional Powder Coated Shelves
• 6" Overall Height Casters (for use in lieu of legs)
• 4" Overall Height Casters (for use in lieu of legs)
• 3-1/2" Overall Height Casters (for use in lieu of legs)
• 2-1/2" Overall Height Casters (for use in lieu of legs, 27"models only)
• Two Year Service/Labor Warranty Available
Compact Undercounter Refrigerators/Self-Contained
Listed by Underwriters Laboratories Inc., to
U.S. and Canadian safety standards and
Listed by NSF International. Approval: ___________________________________
Left To Right Models UHT60, UHT48 & UHT27
27", 48" & 60" Wide Models
27" Wide One Door Model UHT27
48" Wide Two Door Model UHT48
60" Wide Two Door Model UHT60UHT
SERIES
(shown with optional casters)
Stainless Exterior,
Anodized
Aluminum Interior
Finally there is a compact undercounter product worthy of the Traulsen name.
Their rugged construction and high quality components make these units
capable of standing up to the demanding environment of any foodservice
kitchen. Each unit is built with a high quality stainless steel exterior and
durable anodized aluminum interior.
They are also designed for high performance, providing accurate
temperature maintenance. Fresh, safe food is assured, even under the
most demanding conditions.
Their front breathing design allows for "zero-clearance" installation. As a
result they can be placed right up against the backwall and alongside other
kitchen equipment, saving valuable floor space. Additionally, they offer a
wide range of optional accessories to choose from, and are ideal for use with
many different type applications.
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
SECTION
9-1
Plan - UHT27
Plan - UHT48
Elevation - UHT27
Elevation - UHT48
Project Quantity Item #
Model Specified: CSI Section 11400
SECTION
9-1
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
Plan - UHT60
Elevation - UHT60
Section - 27" & 60" Models Section - 48" Models
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
SECTION
9-1
DIMENSIONAL DATA UHT27 UHT48 UHT60
Net capacity cu. ft. 7.1 13.1 16.7
Length - overall in. 27 48 60
Depth - overall in. 307⁄8 307⁄8 307⁄8
Depth - with door open 90° 545⁄8 50 543⁄8
Clear door height in. 241⁄8 241⁄8 241⁄8
Clear door width in. 223⁄4 181⁄4 223⁄4
Height - overall on 6" legs in. 351⁄2 351⁄2 351⁄2
Number of shelves - total 2 4 4
Shelf area sq. ft. 4.88 10.3 13.2
ELECTRICAL DATA
Voltage 115/60/1 115/60/1 115/60/1
Full Load Amperes 3.3 5.7 5.7
Wattage 225 480 480
REFRIGERATION DATA
Refrigerant R-134a R-134a R-134a
BTU/HR - H.P.1 889 (1⁄6 HP) 1869 (1⁄4 HP) 1869 (1⁄4 HP)
SHIPPING DATA
Length - Crated in. 44 631⁄2 751⁄2
Depth - Crated in. 441⁄4 441⁄4 441⁄4
Height - Crated in. 463⁄4 463⁄4 463⁄4
Volume - Crated cu. ft. 53 76 90
Net Wt. lbs. 250 265 355
Gross Wt. lbs. 275 290 380
NOTE: When ordering please specify: Voltage, Hinging, Optional Accessories and any
additional warranties.
Continued product development may necessitate specification changes without notice.
Part No. TR35819 (revised 3/06)
Construction, Hardware and Insulation
Cabinet exterior front, one piece sides, louver assembly and doors are constructed
of 22 gauge stainless steel. Cabinet interior and door liners are constructed of
anodized aluminum. The exterior cabinet back and bottom are constructed of
galvanized steel.
A stainless steel door with a recessed work-flow handle and anodized aluminum liner
is provided. The door self closes at less than 90 degrees and also includes a stay
open feature at 105 degrees. Easily removable for cleaning, vinyl magnetic door
gasket assures tight door seal.
Both the cabinet and door(s) are insulated with an average of 2" thick high density,
non-CFC, foamed in place polyurethane.
Refrigeration System
A balanced, rear mounted, front breathing, self-contained refrigeration system using
R-134a refrigerant is provided. It features a capillary tube metering device, air-cooled
hermetic compressor, a forced air evaporator coil and a non-electric condensate
evaporator. An 8' cord and plug is provided. Standard operating temperature is 34 to
38°F.
Interior
Standard interior arrangements include two (2) powder coated wire shelves per door,
mounted on pilasters. These are adjustable in 1/2" increments, allowing for a mini-
mum of 1-1/2" spacing between shelves.
Warranties
Both a one year parts and labor warranty and a five year compressor warranty (self-
contained models only) are provided standard. An optional 2nd year extended parts
and labor warranty is also available.
Specifications
NOTE: Freight charges are FOB destination for dock to dock
delivery within the continental USA. Liftgate delivery
charges are additional. For inside delivery charges, please
consult factory.
Equipped With One NEMA 5-15 P Plug
NOTES
1= Based on a 90 degree F ambient and 20 degree F evaporator.
ITEM NO.: 231 QUANTITY: 1
DESCRIPTION: BREADING TABLE
MANUFACTURER: RANDELL
MODEL: 52365WPRM-CFA
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 12 AMPS, ½ HP, 115V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
RanSpec Self-Contained Recessed Pan Coldwall Refrigerator model 52365WPRM-CFA
model 52365WPRM-CFA
Standard Features:• Lift-assisted stainless cover that doubles as a work surface when closed• Split-hinged louver doors allowing access to the cold well drain and filter while protecting the controllers and on/off switch• Recessed front edge for easy reach and improved ergonomics to pans• Removable pan adaptor frames • Drain in cold well for easy clean-up• Foamed in place urethane insulation providing superior temperature maintenance and structural durability• 4” casters for easy mobility• Foot pulls on doors for hands-free operation• (3) stainless steel wire shelves behind each door• Removable side panel for easy access to compressor housing• Electrical cord bracket for winding up cord during moving• Stainless steel stand-offs to allow unit to breath• Removable filter for condensing unit
Description:Self-Contained refrigerated breading station with a mechanically cooled upper pan prep area with a lift-assist stainless steel cover (work surface). The mechanically cooled pan opening uses Randell’s exclusive design technologies, such as our aluminum heat-transfer plates for more effective cooling. Rail area is water-tight and supplied with a large drain for easy cleaning. Refrigerated base with three self-closing doors . Base and pan area are controlled independently for more precise temperature maintenance.
Specifications:CABINET EXTERIOR: Top to be one piece of die-formed 16 gauge stainless steel with stainless steel 90-degree front nosing. Top has 90-degree turndown at rear. Overall work surface finishes at 39” AFF. Ends are stainless steel with compressor housing end removable for easy access to mechanical compartment. Rear of unit has a stainless steel finished back panel. Door opening frames are ABS and contain a concealed magnetic strip for positive magnet-to-magnet seal with door gaskets. ABS fronts are supplied with stainless steel capping to prevent pans from damaging plastic. Plastic front provide superior thermal break. Unit is mounted on4” casters for mobility.
CABINET BASE/INTERIOR: Base interior to be thermoplastic at ends and door openings. Stainless steel interior floor and back liner to be coved cornered for easy cleaning. Unit insulation to be CFC free foamed in place urethane.
DOORS: Door fronts to be stainless steel with bottom-mounted foot pulls. The interior liner is one-peice formed stainless steel. The gasket is held in place with a ABS retainer and features Randell’s exclusive Press-Fit Gasket System. Doors are mounted on self-closing cam-style hinges.
REFRIGERATION SYSTEM: System is a balanced heavy duty R-404A refrigerant system with an energy efficient hot gas automatic defrost (for base evaporator coil). The base is cooled by an independent blower coil operating on its own expansion valve system and controlled by its own electronic controller. The mechanically cooled coldwall wrapped rail is provided with a pressure control top operate the condensing unit on demand and a second electronic controller is provided to allow independent settings form the base. Both controllers are located in the compressor housing and are visible behind a plexi-glass window in the hinged louver. Controllers are factory set and locked out to meet CFA operating specifications.
ELECTRICAL: 120 volt 15 amp operation, provided with cord and plug and cord wind up bracket.
TEMPERATURE: Unit is designed to maintain 40 degrees or below in the base and 41 degrees or below in the rail in accordance with NSF Standard 7.
Randell Custom, Page 1PP SPEC0155 Rev. A
Created 12/07
Options & Accessories:Export voltage
1055 Mendell Davis Drive, Jackson, MS 39272888-994-7636, unifiedbrands.netInformation contained in this document is known to be current and accurate at the time of printing/creation. Unified Brands recommends referencing our product line websites, unifiedbrands.net, for the most updated product information and specifications.
MODEL 52365WPRM-CFA
L D H DoorsDoor Opening Clearances Storage
(cubic feet)Pan
Capacity HP Volt Amps NEMAShip
Weight(lbs)Left-Right Top-Bottom Depth
65” 33” 42” (3) 18” 13.25” 22.25” 26” 13.2 (4) 12x20”(1) 1/2-long 1/2HP 115 12 5-15p 740
Model 52365WPRM-CFAPP DWG0001 Rev.
1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.netInformation contained in this document is known to be current and accurate at the time of printing/creation. Unified Brands recommends referencing our product line websites, unifiedbrands.net, for the most updated product information and specifications.
* Height is to work-surface; front edge is at 39” with recessed ledge for easy access to the cold well. With cover in open position, overall height is 72”. Depth is 34” overall with 1” bumper (stand-offs).
ITEM NO.: 236 QUANTITY: 1
DESCRIPTION: FREEZER (SINGLE SECTION)
MANUFACTURER: TRAULSEN
MODEL: RLT132WUT-FHS-ZCF01
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 11.5 AMPS, 120 V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: HGD RIGHT, SHELVES PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Project Quantity Item #
Model Specified: CSI Section 11400
SECTION1-8
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
Standard Product Features• R-Series: Stainless Steel Exterior & Interior• A-Series: Stainless Steel Exterior/Anodized Aluminum Interior• INTELA-TRAUL® Microprocessor Control System• Balanced, Self-Contained Refrigeration System Using R-404A• Scroll Blower Type Evaporator Fan• Biased Return Air Duct• Full or Half Length Stainless Steel Doors With Locks• Self-Closing Doors With Stay Open Feature At 120 Degrees• Guaranteed For Life Cam-Lift Hinges• Guaranteed For Life Horizontal Work Flow Door Handle• Standard Door Hinging: 132W = Right, 232W = Left/Right,
332W = Left/Right/Right (other hingings available)• Automatically Activated Incandescent Lights• Stainless Steel Breaker Caps• Three Chrome Plated Adjustable Shelves Per Section,
Supported On Shelf Pins (installed at the factory)• Automatic Non-Electric Condensate Evaporator• Magnetic Snap-In Door Gaskets• Gasket Protecting Metal Door Liner• Controllable Anti-Condensate Door Perimeter Heaters• Thermostatic Expansion Valve Metering Device• Stainless Steel One-Piece Louver Assembly• 9' Cord & Plug Attached• Set of Four (4) 6" High Adjustable Stainless Steel Legs• One Year Parts And Labor Warranty• Two Year Control Warranty (parts and labor)• Five Year Compressor Warranty
Options & Accessories• Stainless Steel Finished Back With Rear Louvers• Re-Hinging Feature For Door(s)• No. 1 Type Tray Slides To Accommodate either (1) 18" x 26"
or (2) 14" x 18" Sheet Pans, Adjustable To 2" O.C.• No. 2 Type Tray Slides To Accommodate (1) 18" x 26" Sheet
Pans, Adjustable To 2" O.C.• No. 3 Type Tray Slides To Accommodate (2) 12" x 20" Steam
Table Pans, Adjustable To 2" O.C.• No. 4 Type Tray Slides To Accommodate (1) 18" x 26" Sheet
Pans (chrome rod type, equips 1/2 section)• Universal Type Tray Slides To Accommodate Either (1)
18" x 26" or (2) 14" x 18" Sheet Pans, or (2) 12" x 20" SteamTable Pans, Adjustable To 4" O.C.
• Additional Chrome Plated Shelves• Locking Hasps (padlocks supplied by others)• Export 220/50/1 Voltage• 208/115/60/1 Voltage In Lieu Of Standard 115/60/1• Stainless Steel Shelves In Lieu of Standard Chrome Plated• Kool Klad Exterior Laminate Decor• Set of Four (4) 6" High Casters In Lieu of Legs• Set of Four (4) 4-7/16" High Casters In Lieu of Legs• 4-1/2" High Stainless Steel Base In Lieu of Legs• 6" High Stainless Steel Kickplate (for use with standard legs)• Prison/Correctional Facilities Options• Remote Applications (see spec sheet 12-2 for more details)• Two Year Service/Labor Warranty Available
"W-Width" Reach-In Freezer Models/Self-Contained
Listed by Underwriters Laboratories Inc., toU.S. and Canadian safety standards andListed by NSF International. Approval: ___________________________________
Model RLT132WUT-FHS
One, Two & Three Section Models, 32" Deep1-Section Full Length Door Model RLT132WUT-FHS2-Section Full Length Door Model RLT232WUT-FHS3-Section Full Length Door Model RLT332WUT-FHS1-Section Half Length Door Model RLT132WUT-HHS2-Section Half Length Door Model RLT232WUT-HHS3-Section Half Length Door Model RLT332WUT-HHS
RSERIES
ASERIES
1-Section Full Length Door Model ALT132WUT-FHS2-Section Full Length Door Model ALT232WUT-FHS3-Section Full Length Door Model ALT332WUT-FHS1-Section Half Length Door Model ALT132WUT-HHS2-Section Half Length Door Model ALT232WUT-HHS3-Section Half Length Door Model ALT332WUT-HHS
(shown with optional casters)
INTELA-TRAUL®
Equipped!
Stainless Exterior& Interior
Stainless Exterior,Anodized
Aluminum Interior
The R & A Series represent Traulsen's Top-of-the-Line product offering. The“W-Width” reach-in freezer models are all designed to offer maximuminterior storage capacity. Each is supplied standard with such high qualityfeatures as balanced refrigeration systems, microprocessor controls,communications ability and stainless steel exteriors. Additionally, they offerthe widest range of optional accessories to choose from, and can bespecified for use with many different applications, including: Foodservice,Correctional, Institutional, Export, etc.
NOTE: Full load amps and plug style may vary dependingon electrical options chosen and condensing unit employed.
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302Website: www.traulsen.com
SECTION1-8
DIMENSIONAL DATA R/ALT132WUT R/ALT232WUT R/ALT332WUT
Net capacity cu. ft. 24.2 (686 cu l) 51.6 (1462 cu l) 79.0 (2238 cu l)
Length - overall in. 297⁄8 (75.9 cm) 58 (147.3 cm) 861⁄8 (218.8 cm)
Depth - overall in. 35 (88.8 cm) 35 (88.8 cm) 35 (88.8 cm)
Depth - less handle in. 333⁄4 (84.4 cm) 333⁄4 (84.4 cm) 333⁄4 (84.4 cm)
Depth - over body in. 32 (81.3 cm) 32 (81.3 cm) 32 (81.3 cm)
Depth - door open 90° in. 5711⁄16 (146.5 cm) 5711⁄16 (146.5 cm) 5711⁄16 (146.5 cm)
Clear door width in. 211⁄8 (53.6 cm) 211⁄8 (53.6 cm) 211⁄8 (53.6 cm)
Clear half-door height in. 271⁄2 (69.9 cm) 271⁄2 (69.9 cm) 271⁄2 (69.9 cm)
Clear full-door height in. 575⁄8 (146.3 cm) 575⁄8 (146.3 cm) 575⁄8 (146.3 cm)
Height - overall on 6" legs 831⁄4 (211.5 cm) 831⁄4 (211.5 cm) 831⁄4 (211.5 cm)
No. Standard Shelves 3 6 9
Shelf area sq. ft.1 18.8 (1.75 sq m) 37.6 (3.49 sq m) 56.4 (5.23 sq m)
ELECTRICAL DATA
Voltage 115/60/1 115/60/1 208/115/60/1
Feed wires with Ground 3 3 4
Full load amperes 11.5 14.9 10.8
REFRIGERATION DATA
Refrigerant R-404A R-404A R-404A
BTU/HR H.P.2 2160 (1⁄2 HP) 3790 (3⁄4 HP) 4710 (1 HP)
SHIPPING DATA3
Length - crated in. 35 (89 cm) 63 (160 cm) 91 (231 cm)
Depth - crated in. 43 (109 cm) 43 (109 cm) 43 (109 cm)
Height - crated in. 831⁄2 (212 cm) 831⁄2 (212 cm) 831⁄2 (212 cm)
Volume - crated cu. ft. 71 (2011 cu l) 131 (3711 cu l) 189 (5354 cu l)
RLT Net Wt. lbs. 415 (188 kg) 705 (320 kg) 940 (426 kg)
RLT Gross Wt. lbs. 505 (229 kg) 845 (383 kg) 1120 (508 kg)
ALT Net Wt. lbs. 365 (166 kg) 625 (283 kg) 820 (372 kg)
ALT Gross Wt. lbs. 455 (206 kg) 765 (347 kg) 1000 (454 kg)
NOTE: When ordering please specify: Voltage, Hinging, Door Size, Options and anyadditional warranties.
Continued product development may necessitate specification changes without notice.Part No. TR35762 (revised 4/04)
Construction, Hardware and InsulationCabinet exterior front, one piece sides, louver assembly and doors are constructedof 20 gauge stainless steel with #4 finish. Cabinet interior and door liners areconstructed of stainless steel (anodized aluminum in the A-Series). The exterior cabinettop, back and bottom are constructed of heavy gauge aluminized steel. A set of four(4) adjustable 6" high stainless steel legs are included.
Doors are equipped with a gasket protecting metal door pan, removable plugcylinder locks and guaranteed for life cam-lift, gravity action, self-closing metal, glidehinges with stay open feature at 120 degrees. Hinges include a concealed switch toautomatically activate the interior incandescent lighting. Guaranteed for life, workflow door handles are mounted horizontally over recess in door which limitsprotrusion from door face into aisleways. Doors have seamless, polished metalcorners.
Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal.Anti condensate heaters are located behind each door opening.
Both the cabinet and door(s) are insulated with an average of 2" thick high density,non-CFC, foamed in place polyurethane.
Refrigeration SystemA top mounted, self-contained, balanced refrigeration system using R-404Arefrigerant is conveniently located behind the one piece louver assembly. It featuresan easy to clean front facing condenser, thermostatic expansion valve, air-cooledhermetic compressor, plenum effect blower coil, large, high humidity evaporator coillocated outside the food zone and a top mounted non-electric condensateevaporator. Biased return air duct protects against introduction of warm kitchen air,promoting even temperature maintenance and efficient operation. A 9' cord andplug is provided. Standard operating temperature is 0 to -5°F.
ControllerThe easy to use water resistant INTELA-TRAUL® microprocessor control system issupplied standard. Unit is NAFEM Data Protocol communication (NDP) ready.Optional hardware required to be NDP compliant. Third party software required fornetwork connection. It includes a 3-Digit LED Display, Fahrenheit or CelsiusTemperature Scale Display Capability, Defrost Lockouts, and an RS485 data port.In addition it includes audio/visual alarms for: Hi/Lo Cabinet Temperature, Door Open,Clean Condenser, Evaporator Coil and Discharge Line Sensor Failures, and PowerSupply Interruption.
InteriorStandard interior arrangements include three (3) chrome plated wire shelves persection, mounted on shelf pins. Shelves are full-width, and do not have any largegaps between them requiring the use of "bridge" or "junior shelves." Recommendedload limit per shelf should not exceed 225 lbs. Optional tray slides may bepurchased in combination with, or in lieu of these. Both standard and optionalinterior arrangements are completely installed at the factory.
WarrantiesBoth a one year parts and labor warranty and a five year compressor warranty (self-contained models only) are provided standard. An optional 2nd year extended partsand labor warranty is also available. In addition the INTELA-TRAUL® control iswarranted by a two year parts and labor warranty.
Specifications
NOTESNOTE: Figures in parentheses reflect metric equivalents.1= Area of standard shelf compliment only, does not include storage area of additional shelves or available
on cabinet bottom.2= Based on a 90 degree F ambient and -10 degree F evaporator.3= For approximate remote weights deduct 40 lbs. from respective net or gross weight. For other information
on remote models, please refer to spec sheet 12-2.
Plan - R/ALT132WUT
Elevation -R/ALT132WUT
Section - All Models
Plan - R/ALT232WUT
Elevation -R/ALT232WUT
Plan - R/ALT332WUT
Elevation -R/ALT332WUT
NEMA Plug Chart For Freezer Models
1-SectionModels5-15P
2-SectionModels5-20P
3-SectionModels
L14-20P
ITEM NO.: 238 QUANTITY: 1
DESCRIPTION: REFRIGERATOR 1 SECTION W/ GLASS FRONT
MANUFACTURER: TRAULSEN
MODEL: RHT126WUT-ZCF02
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 9 AMPS, 120V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: HH DRS HGD LEFT PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Project Quantity Item #
Model Specified: CSI Section 11400
SECTION
11-5
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
Standard Product Features• R-Series: Stainless Steel Exterior & Interior
• A-Series: Stainless Steel Exterior/Anodized Aluminum Interior
• INTELA-TRAUL® Microprocessor Control System
• Balanced, Self-Contained Refrigeration System Using R-134a
• Scroll Blower Type Evaporator Fan
• Biased Return Air Duct
• Full or Half Length Hinged Glass Doors With Locks
• Self-Closing Doors With Stay Open Feature At 120 Degrees
• Guaranteed For Life Cam-Lift Hinges
• Stainless Steel Vertical Door Handle(s)
• Standard Door Hinging: 126W = Right, 226W = Left/Right,
(other hingings available)
• Incandescent Lights With Exterior Switch
• Stainless Steel Breaker Caps
• Three Chrome Plated Adjustable Shelves Per Section,
Supported On Shelf Pins (installed at the factory)
• Automatic Non-Electric Condensate Evaporator
• Magnetic Snap-In Door Gaskets
• Gasket Protecting Metal Door Liner
• Controllable Anti-Condensate Door Perimeter Heaters
• Thermostatic Expansion Valve Metering Device
• Stainless Steel One-Piece Louver Assembly
• 9' Cord & Plug Attached
• Set of Four (4) 6" High Adjustable Stainless Steel Legs
• One Year Parts And Labor Warranty
• Two Year Control Warranty (parts and labor)
• Five Year Compressor Warranty
Options & Accessories• Stainless Steel Finished Back With Rear Louvers
• Fluorescent Lights
• Re-Hinging Feature For Door(s)
• Additional Chrome Plated Shelves
• Export 220/50/1 Voltage
• 208/115/60/1 Voltage In Lieu Of Standard 115/60/1
• Stainless Steel Shelves In Lieu of Standard Chrome Plated
• Kool Klad Exterior Laminate Decor
• Set of Four (4) 6" High Casters In Lieu of Legs
• Set of Four (4) 4-7/16" High Casters In Lieu of Legs
• 4-1/2" High Stainless Steel Base In Lieu of Legs
• 6" High Stainless Steel Kickplate (for use with standard legs)
• Remote Applications (see spec sheet 12-2 for more details)
• Two Year Service/Labor Warranty Available
Shallow Depth Hinged Glass Door Reach-InRefrigerators/Self-Contained
Listed by Underwriters Laboratories Inc., to
U.S. and Canadian safety standards and
Listed by NSF International. Approval: ___________________________________
Model RHT126WUT-HHG
One & Two Section Models, 26" Deep
1-Section Full Length Door Model RHT126WUT-FHG
2-Section Full Length Door Model RHT226WUT-FHG
1-Section Half Length Door Model RHT126WUT-HHG
2-Section Half Length Door Model RHT226WUT-HHG
RSERIES
ASERIES
1-Section Full Length Door Model AHT126WUT-FHG
2-Section Full Length Door Model AHT226WUT-FHG
1-Section Half Length Door Model AHT126WUT-HHG
2-Section Half Length Door Model AHT226WUT-HHG
(shown with optional fluorescent lights & casters)
INTELA-TRAUL®
Equipped!
Stainless Exterior
& Interior
Stainless Exterior,
Anodized
Aluminum Interior
The R & A Series represent Traulsen's Top-of-the-Line product offering. These
26" Deep reach-in refrigerator models are equipped with hinged glass doors
in order to maximize product visibility. Each is supplied standard with such
high quality features as balanced refrigeration systems, microprocessor
controls, communications ability and stainless steel exteriors. Additionally,
they offer the widest range of optional accessories to choose from, and can
be specified for use with many different applications, including: Foodservice,
Correctional, Institutional, Export, etc.
NOTE: Full load amps and plug style may vary depending
on electrical options chosen and condensing unit employed.
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN
4401 BLUE MOUND RD. FT. WORTH, TX 76106
PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302
Website: www.traulsen.com
SECTION
11-5
DIMENSIONAL DATA R/AHT126WUT R/AHT226WUT
Net capacity cu. ft. 19.1 (541 cu l) 40.8 (1156 cu l)
Length - overall in. 297⁄8 (75.9 cm) 58 (147.3 cm)
Depth - overall in. 29 (73.6 cm) 29 (73.6 cm)
Depth - less handle in.
Depth - over body in. 26 (66.0 cm) 26 (66.0 cm)
Depth - door open 90° in. 5711⁄16 (146.5 cm) 5711⁄16 (146.5 cm)
Clear door width in. 211⁄2 (54.6 cm) 211⁄2 (54.6 cm)
Clear half-door height in. 271⁄2 (69.9 cm) 271⁄2 (69.9 cm)
Clear full-door height in. 575⁄8 (146.3 cm) 575⁄8 (146.3 cm)
Height - overall on 6" legs 831⁄4 (211.5 cm) 831⁄4 (211.5 cm)
No. Standard Shelves 3 6
Shelf area sq. ft.1 14.6 (1.35 sq m) 29.2 (2.71 sq m)
ELECTRICAL DATA
Voltage 115/60/1 115/60/1
Feed wires with Ground 3 3
Full load amperes2 8.0 10.3
Full load amperes3 9.0 (2 lamps) 12.2 (3 lamps)
REFRIGERATION DATA
Refrigerant R-134a R-134a
BTU/HR H.P.4 2220 (1⁄3 HP) 4200 (1⁄2 HP)
SHIPPING DATA5
Length - crated in. 35 (89 cm) 63 (160 cm)
Depth - crated in. 43 (109 cm) 43 (109 cm)
Height - crated in. 831⁄2 (212 cm) 831⁄2 (212 cm)
Volume - crated cu. ft. 73 (2068 cu l) 131 (3711 cu l)
RHT Net Wt. lbs. 345 (156 kg) 550 (249 kg)
RHT Gross Wt. lbs. 435 (197 kg) 690 (313 kg)
AHT Net Wt. lbs. 305 (138 kg) 480 (218 kg)
AHT Gross Wt. lbs. 395 (179 kg) 620 (281 kg)
NOTE: When ordering please specify: Voltage, Hinging, Door Size, Options and any
additional warranties.
Continued product development may necessitate specification changes without notice.
Part No. TR35830 (revised 4/04)
Construction, Hardware and Insulation
Cabinet exterior front, one piece sides and louver assembly are constructed of 20
gauge stainless steel with #4 finish. Cabinet interior is constructed of stainless steel
(anodized aluminum in the A-Series). The exterior cabinet top, back and bottom are
constructed of heavy gauge aluminized steel. A set of four (4) adjustable 6" high
stainless steel legs are included.
Doors are equipped with removable plug cylinder locks and guaranteed for life cam-
lift, gravity action, self-closing metal, glide hinges with stay open feature at 120
degrees. An external switch is provided to activate the interior incandescent lighting.
Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal.
Anti condensate heaters are located behind each door opening.
The cabinet is insulated with an average of 2" thick high density, non-CFC, foamed in
place polyurethane.
Refrigeration System
A top mounted, self-contained, balanced refrigeration system using R-134a
refrigerant is conveniently located behind the one piece louver assembly. It features
an easy to clean front facing condenser, thermostatic expansion valve, air-cooled
hermetic compressor, plenum effect blower coil, large, high humidity evaporator coil
located outside the food zone and a top mounted non-electric condensate
evaporator. Biased return air duct protects against introduction of warm kitchen air,
promoting even temperature maintenance and efficient operation. A 9' cord and
plug is provided. Standard operating temperature is 34 to 38°F.
Controller
The easy to use water resistant INTELA-TRAUL® microprocessor control system is
supplied standard. Unit is NAFEM Data Protocol communication (NDP) ready.
Optional hardware required to be NDP compliant. Third party software required for
network connection. It includes a 3-Digit LED Display, Fahrenheit or Celsius
Temperature Scale Display Capability, and an RS485 data port. In addition it
includes audio/visual alarms for: Hi/Lo Cabinet Temperature, Door Open, Clean
Condenser, Evaporator Coil and Discharge Line Sensor Failures, and Power Supply
Interruption.
Interior
Standard interior arrangements include three (3) chrome plated wire shelves per
section, mounted on shelf pins. Shelves are full-width, and do not have any large
gaps between them requiring the use of "bridge" or "junior shelves." Recommended
load limit per shelf should not exceed 225 lbs. Both standard and optional
interior arrangements are completely installed at the factory.
Warranties
Both a one year parts and labor warranty and a five year compressor warranty (self-
contained models only) are provided standard. An optional 2nd year extended parts
and labor warranty is also available. In addition the INTELA-TRAUL® control is
warranted by a two year parts and labor warranty.
Specifications
NOTESNOTE: Figures in parentheses reflect metric equivalents.1= Area of standard shelf compliment only, does not include storage area of additional shelves or available
on cabinet bottom.2= Amp figure shown as supplied with standard incandescent lighting.3= Amp figure shown as supplied with optional fluorescent lighting, note that 2-section models will be
supplied with a NEMA 5-20P plug as a result.4= Based on a 90 degree F ambient and 20 degree F evaporator.5= For approximate remote weights deduct 40 lbs. from respective net or gross weight. For other information
on remote models, please refer to spec sheet 12-2.
NOTE: Freight charges are FOB destination for dock to dock delivery
within the continental USA. Liftgate delivery charges are additional. For
inside delivery charges, please consult factory.
Equipped With OneNEMA 5-15P Plug
2 Section Fluorescent LightModels Are Equipped With OneNEMA 5-20P Plug
Section - All Models
Plan -
R/AHT126WUT
Elevation -
R/AHT126WUT
Plan - R/AHT226WUT
Elevation -
R/AHT226WUT
ITEM NO.: 242 QUANTITY: 1
DESCRIPTION: EVENTHAW REFRIGERATOR W/ SLIDES
MANUFACTURER: TRAULSEN/HOBART
MODEL: RET232N-ZCF01
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 16 AMPS, ½ HP, 115V, 1 PHASE, PLUG, NEMA 5-20R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Project Quantity Item #
Model Specified: CSI Section 11400
Chick-fil-A #3Reach-In Even-ThawRefrigerator Model
TRAULSEN & CO., INC.4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302E-Mail: [email protected]
Standard Features• Stainless Steel Exterior
• Stainless Steel Interior
• Full Length Stainless Steel Doors
• Self-Closing Doors With Stay Open Feature At 120 Degrees
• Guaranteed For Life Cam-Lift Hinges
• Guaranteed For Life Horizontal Work Flow Door Handle
• Stainless Steel Breaker Caps
• Twenty Eight (28) #1 Type Tray Slides 4" O.C. (14 persection)
• Automatic Non-Electric Condensate Evaporator
• Exterior Mounted Dial Thermometer
• Magnetic Snap-In Door Gaskets
• Cord & Plug Attached
• Set Of Four (4) 6" High Casters
• 1 Year Parts And Labor Warranty
• 5 Year Compressor Warranty
The R-Series “N-Width” Even Thaw Refrigerator is de-signed especially to thaw frozen food product under safe,temperature controlled conditions. This model isequipped standard with tray slides to accommodate ei-ther: one (1) 18" x 26" or two (2) 14" x 18" pans per pairof tray slides. It can be used to thaw either full or partialloads of frozen food product.
NOTE: Using this refrigerator for storage of uncoveredproduct is not recommended.
Reach-In Even-Thaw Refrigerator/Self-Contained
Approval: __________________________________
R Models RET232NUT-FHSSERIES Two Section Reach-In Model
Model RET232NUT-FHS
Project Quantity Item #
Model Specified: CSI Section 11400
TRAULSEN & CO., INC.4401 BLUE MOUND RD. FT. WORTH, TX 76106PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302E-Mail: [email protected]
Chick-fil-A #3Reach-In Even-ThawRefrigerator Model
NOTE: When ordering please specify: Voltage, Hinging, Door Size, Options andany additional warranties. For fast order entry: Fax 1 (800) 765-8728.
Continued product development may necessitate specification changes without notice.Part No. Chick-fil-A #3 (revised 4/03)
Uses One NEMA 5-20 P Plug
Construction, Hardware and InsulationCabinet exterior, including front, one piece sides, louver assembly and doors areconstructed of heavy gauge stainless steel. Cabinet interior and door liners are con-structed of stainless steel. Exterior cabinet top, back and bottom are constructed ofheavy gauge aluminized steel. Adjustable 6" high stainless steel legs are included.
Doors are equipped with removable plug cylinder locks and guaranteed for life cam-lift, gravity action, self-closing metal, glide hinges with stay open feature at 120 de-grees. Guaranteed for life, work flow door handle is mounted horizontally over re-cess in door which limits protrusion from door face into aisleways.
Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal.Anti condensate heaters are located behind each door opening.
Cabinet and door contains high density, non-CFC, foamed in place polyurethaneinsulation.
Refrigeration SystemA top mounted, self-contained, balanced refrigeration system using R-134a refriger-ant is conveniently located behind the one piece louver assembly. It features a ple-num effect blower coil, large, high humidity evaporator coil located outside the foodzone, and a top mounted non-electric condensate evaporator. Heaters and fansmounted in the mullion facilitate the Even-Thaw process. Standard operating tem-perature is 37 to 41°F.
InteriorStandard interior arrangements include twenty eight (28) #1 tray slides 4" O.C., four-teen per section. Each pair of tray slides can accommodate either: (1) 18" x 26" or (2)14" x 18" pans.
WarrantiesThe standard warranty includes a five year compressor warranty and a one yearparts and labor warranty on all components and the cabinet.
Specifications
NOTESNOTE: Figures in parentheses reflect metric equivalents.1=Wattage is determined by listed amps X listed volts X an average run timeof 70% for refrigerators and 80% for freezers.2=Based on a 90 degree F ambient and 20 degree F evaporator.
DIMENSIONAL DATA RET232NUT-FHS
Net capacity cu. ft. 46.0 (1303 cu l)Length - overall in. 521⁄8 (132.4 cm)
Depth - overall in. 35 (88.8 cm)Depth - over body in. 32 (81.3 cm)
Depth - with door open 553⁄4 (141.6 cm)90 degrees in.
Clear door width in. 211⁄8 (53.6 cm)
Clear full-door height in. 575⁄8 (146.3 cm)
Height - overall on 6" legs 831⁄4 (211.5 cm)Pan Capacity - 18" x 26" 28
Pan Capacity - 14" x 18" 56ELECTRICAL DATA
Voltage 115/60/1Feed wires with Ground 3
Full load amperes 16.0REFRIGERATION DATA
Refrigerant R-134aBTU/HR H.P.2 5120 (3⁄4 HP)
SHIPPING DATALength - crated in. 63 (160 cm)
Depth - crated in. 43 (109 cm)Height - crated in. 83 1⁄2 (212 cm)
Volume - crated cu. ft. 131 (3711 cu l)Net Wt. lbs. 560 (254 kg)
Gross Wt. lbs. 700 (318 kg)
ITEM NO.: 246 QUANTITY: 1
DESCRIPTION: BUN TOASTER
MANUFACTURER: PRINCE CASTLE INC
MODEL: 297-T12PHH
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 13 AMPS, 1.5 KW, 120V, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
297-0800
297 SERIESSLIM-LINE VERTICALCONTACT TOASTER
SLIM
-LIN
E V
ER
TIC
AL
CO
NT
AC
T T
OA
STE
R297 SE
RIE
S
STANDARD FEATURES
� Delivers higher speeds and temperature whilemaintaining proven reliable design
� Stronger motor and higher temperature platenincreases performance
� 297-T12P model includes passive heat source toincrease internal bun temperature, producing amore appetizing bun
� Unique two-level platen design allows operatorsto toast thicker bun crowns and thinner bunheels at the same time
� Adjustable bun crush controls and thermostatallows precise toasting for various breadproducts
� Compact design requires only 8" (20.3cm) ofcounter space depth
� 12-, 20-, 30- and 40-second toasting models areavailable
� Re-designed conveyor assembly improvesreliability
� Easy to clean and maintain
� Adjustable thermostat for precise toasting
� Two-year parts and labor warranty
Prince Castle's Slim-line Bun Toaster provides perfectcarmelization by contact toasting. These toasters putversatility in your kitchen by using less counter space. Aunique two-level platen design allows operators to toastthicker bun crowns and thinner bun heels at the sametime. A self-adjusting chain assembly provides propertensioning and helps prevent binding. Model 297-T12Ptoasts 2000 buns per hour while also featuring passiveheaters that increase internal bun temperature. Model297-T40 toasts up to 720 buns per hour, and Model297-T20 toasts up to 1400 buns per hour. Stainless-steelconstruction makes this toaster durable and easy-to-clean.
All Prince Castle Slim-line Toasters feature a Teflonâ
coated platen; plus for extra protection against bunsticking, a Teflonâ sheet kit consisting of a stainless-steelclamp and two Teflonâ sheets are included. Thesesheets are used one at a time over the platen to protectthe toasting surface, to eliminate bun sticking, and tokeep the toaster clean and working properly.
Model 297-T12P
02'(/�180%(5 92/76 += :$776 $0363/8*
180%(5
3/8*&21),*�
����+7��
��� �� ���� �� ����3����+7��3
����+7��
����+7��
����+7��)&(
��� �� ���� � &((�������+7��3)&(
����+7��)&(
����+7��)&(
02'(/
180%(5 '(6&5,37,21:,'7+
,1���&0�+(,*+7
,1���&0�'(37+,1���&0�
6+,33,1*�:7
/%�� �.*�
����7�� ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
����
������
����
������
���
������
��
������
����7��3 ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
����7�� ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
����7�� ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
����7��)&( ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
����7��3)&( ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
����7��)&( ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
����7��)&( ���VHF��9HUWLFDO�&RQWDFW�7RDVWHU
SPECIFICATIONS
*Designs and specifications are subject to change without notice.
297
SER
IES
SLIM
-LIN
E V
ER
TIC
AL
CO
NT
AC
T T
OA
STE
RS
297 SERIESSLIM-LINE VERTICALCONTACT TOASTER
DIMENSIONS
ELECTRICAL
*297 units equipped with 6 ft. (182.8cm) line cord.
PRODUCTOUTPUT
02'(/
180%(5 %816�+285
����7�� ���
����7��3 ����
����7�� ����
����7�� ����
8.62(21.9cm)
2.19 (5.56cm) TOCENTER OF POWERCORD
25.67(65.2cm)
25.50(64.77cm)
3.11(7.9cm)
ITEM NO.: 247 QUANTITY: 2
DESCRIPTION: WARMING DRAWER (TWO DRAWER)
MANUFACTURER: TOASTMASTER
MODEL: 3B80A
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 8.7 AMPS, 1 KW, 120V, 1 PHASE, DIRECT WIRE PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
ApplicationHot food servers are designed to holdcooked foods at safe, thermometer veri-fied, serving temperature and propermoisture content. Hot food can beplaced into the drawer(s) either directlyor in separate open pans or containers.Holding temperature and moisture con-tent can be set for the type of food beingheld.
General InformationBuilt in, drawer type hot food serverscome in one, two or three drawer mod-els. Each drawer is furnished withremovable, deep drawn stainless steelpan 221⁄2" W x 51⁄4" H x 133/8" D. Seedimensional data and preheat chart onreverse side.
ConstructionFrame is of welded and reinforced sheetsteel. The body is of aluminized steelwith stainless steel drawer fronts andflange. The integral front flange extendsbeyond the body 1⁄2" at top and bottomand 3⁄8" at sides. Drawers are equippedwith handle operated latching mecha-nism and positive stop. Drawers glide on
third member suspension system rails.Third members have 5 roller bearings(load support) and 5 guide bearings(smooth operation) each (i.e. 20 bear-ings per drawer).
InsulationFully insulated on all six sides, includingdrawer fronts with fiber glass, blankettype insulation.
ElectricalProvided with 48" flexible metal conduitfor electrical connection. Available in120V or 208/240V models. Single phaseonly. CE units available in 230V. Seeelectrical data chart on reverse side.
HeatingHeating is accomplished by preformedtubular heating elements. Model 3A80Ahas one heating element located in thebottom unit. Models 3B80A and 3C80Aeach have two heating elements locatedon the lower sides.
ControlsTemperature is regulated by a hydraulicthermostat adjustable from 100° to
200°F, with “OFF” position. Thermostatcontrol is mounted on the front, belowthe drawer(s) and is equipped with adja-cent signal light. Thermostat controlknob is protected by a knob guard onmodel 3A80A. Models 3B80A and3C80A have a thermostat control knobmounted in a recessed stainless steelmounting cup. Each drawer is fitted witha moisture control slide adjustmentlocated at center front above each draw-er. A thermometer accurately reflects thetemperature at the coolest point insidethe server. This safety feature helpsensure that food products are being heldat a temperature above the bacterialgrowth level, and at temperatures belowthose that may over cook or dry out foodproduct.
CapacityUnit is designed to hold precooked foodsat serving temperature. Ideal for bakedpotatoes, vegetables, ribs, buns androlls. Each drawer holds one 12” x 20” x5” deep pan. Nominal capacities perdrawer:• 40 Baked Potatoes (120 count)• 8 #10 Cans Vegetables• 30 lb. Ribs• 6
1⁄2 doz. Hamburger Buns
• 7 doz. Dinner Rolls
Agency DataHot Food Servers are Underwriters’Laboratories, Inc. listed; NSF and CanadianStandards Association* certified.*CSA listed models are available throughCanadian Distributors only.
No Quibble WarrantyWarranty includes one year parts andlabor, on-site service. (U.S.A. only).
Ordering Information❒ 3A80A - 120V, 1 phase only❒ 3A80A - 208/240V, 1 phase only❒ 3B80A - 120V, 1 phase only❒ 3B80A - 208/240V, 1 phase only❒ 3C80A - 120V, 1 phase only❒ 3C80A - 208/240V, 1 phase only❑ ACCPANALL - extra pans for 80 series ❑ ACRK3B - Drawer Rack❑ ACC3B84GRTE - Grate❑ ACFB201 - Perforated Pan
Foodservice EquipmentJob_________ Item#_________
Hot Food ServersBuilt In Models 3A80A, 3B80A & 3C80A
A MIDDLEBY COMPANY1400 Toastmaster DriveElgin, Illinois 60120 USA1-800-323-2210 • Fax: 1-800-635-4725www.middleby.com
Form 203
3A80A 3B80A 3C80ACONNECTED LOAD AND ELECTRICAL DATA
MODELTOTAL kW NOMINAL AMPERES 1-PHASE
120V 208V 230V 240V 120V 208V 230V 240V
3A80A .45 .40 .47 .54 3.91 1.97 1.96 1.96
3B80A 1.00 .90 1.00 1.2 8.70 4.33 4.35 4.33
3C80A 1.35 1.2 1.35 1.6 11.74 5.87 5.87 5.88
1400 Toastmaster Drive, Elgin, IL 60120-9272 USA • 1-800-323-2210 • Fax: 1-800-635-4725www.middleby.com
Printed in U.S.A. 10/99 Form 203
INTENDED FOR COMMERCIAL USE ONLY. NOT FOR HOUSEHOLD USE.Toastmaster, in line with its policy to continually improve its products, reserves the right to change materials orspecifications without notice. Such revisions do not entitle the buyer to corresponding changes, improvements,
additions, or replacements for previously purchased equipment.
NOTE: All Figures In Parentheses Are In Millimeters.
Hot Food ServersBuilt In Models3A80A, 3B80A & 3C80A
DIMENSION AND PREHEAT DATA
MODELBODY DIMENSIONS DRAWER DIMENSIONS PREHEAT TIME IN MINUTES WEIGHTS
WIDE DEEP HIGH LONG WIDE DEEP 150°F 175°F INSTALLED SHIPPING
3A80A 29.1875" 19.2187" 10.875" 13.4375" 22.5625" 5.25" 18.8 26.2 72 84(741.3625) (488.1549) (276.225) (341.3125) (573.0875) (133.35)
3B80A 29.1875" 19.2187" 21.75" 13.4375" 22.5625" 5.25" 18.8 26.2 125 144(741.3525) (488.1549) (552.45) (341.3125) (573.0875) (133.35)
3C80A 29.1875" 19.2187" 29.3125" 13.4375" 22.5625" 5.25" 20.6 28.2 171 186(741.3625) (488.1549) (744.5375) (341.3125) (573.0875) (133.35)
A. TWO SUPPORTS TO BE PROVIDED. TOPFACE OF SUPPORTS 19.25" (488.95) MIN.,.0625" (1.5875) BELOW BOTTOM EDGE OFOPENING.
B. CROSS BRACE OF WOOD OR METAL TO BEPROVIDED TO HOLD UNIT IN PLACE.
NOTE: IF FLAT PLATFORM IS USED, TOP SUR-FACE SHOULD ALSO BE .0625" (1.5875)BELOW BOTTOM EDGE OF OPENING.
TOP VIEW
CUT-OUT DIMENSIONS andINSTALLATION DATA
SIDE VIEW
3A80A 3B80A 3C80A
3A80A 3B80A 3C80A
NOTE: All Figures In Parentheses Are In Millimeters.
Hot Food ServersBuilt In Models3A80A, 3B80A & 3C80A
Printed in U.S.A. 10/99 Form 203
Two mounting holesare located insidebottom of hot foodserver. See installa-tion data.
FRONT VIEW
3A80A
3B80A
3C80A
Printed in U.S.A. 10/99 Form 203
ID PLATE
ID PLATE
ID PLATE
ID Plate
A. TWO SUPPORTS TO BE PROVIDED. TOPFACE OF SUPPORTS 19.25" (488.95) MIN.,.0625" (1.5875) BELOW BOTTOM EDGE OFOPENING.
B. CROSS BRACE OF WOOD OR METAL TO BEPROVIDED TO HOLD UNIT IN PLACE.
NOTE: IF FLAT PLATFORM IS USED, TOP SUR-FACE SHOULD ALSO BE .0625" (1.5875)BELOW BOTTOM EDGE OF OPENING.
TOP VIEW
CUT-OUT DIMENSIONS andINSTALLATION DATA
SIDE VIEW
3A80A 3B80A 3C80A
3A80A 3B80A 3C80A
NOTE: All Figures In Parentheses Are In Millimeters.
Hot Food ServersBuilt In Models3A80A, 3B80A & 3C80A
Printed in U.S.A. 10/99 Form 203
Two mounting holesare located insidebottom of hot foodserver. See installa-tion data.
FRONT VIEW
3A80A
3B80A
3C80A
Printed in U.S.A. 10/99 Form 203
ID PLATE
ID PLATE
ID PLATE
ID Plate
ApplicationHot food servers are designed to holdcooked foods at safe, thermometer veri-fied, serving temperature and propermoisture content. Hot food can beplaced into the drawer(s) either directlyor in separate open pans or containers.Holding temperature and moisture con-tent can be set for the type of food beingheld.
General InformationBuilt in, drawer type hot food serverscome in one, two or three drawer mod-els. Each drawer is furnished withremovable, deep drawn stainless steelpan 221⁄2" W x 51⁄4" H x 133/8" D. Seedimensional data and preheat chart onreverse side.
ConstructionFrame is of welded and reinforced sheetsteel. The body is of aluminized steelwith stainless steel drawer fronts andflange. The integral front flange extendsbeyond the body 1⁄2" at top and bottomand 3⁄8" at sides. Drawers are equippedwith handle operated latching mecha-nism and positive stop. Drawers glide on
third member suspension system rails.Third members have 5 roller bearings(load support) and 5 guide bearings(smooth operation) each (i.e. 20 bear-ings per drawer).
InsulationFully insulated on all six sides, includingdrawer fronts with fiber glass, blankettype insulation.
ElectricalProvided with 48" flexible metal conduitfor electrical connection. Available in120V or 208/240V models. Single phaseonly. CE units available in 230V. Seeelectrical data chart on reverse side.
HeatingHeating is accomplished by preformedtubular heating elements. Model 3A80Ahas one heating element located in thebottom unit. Models 3B80A and 3C80Aeach have two heating elements locatedon the lower sides.
ControlsTemperature is regulated by a hydraulicthermostat adjustable from 100° to
200°F, with “OFF” position. Thermostatcontrol is mounted on the front, belowthe drawer(s) and is equipped with adja-cent signal light. Thermostat controlknob is protected by a knob guard onmodel 3A80A. Models 3B80A and3C80A have a thermostat control knobmounted in a recessed stainless steelmounting cup. Each drawer is fitted witha moisture control slide adjustmentlocated at center front above each draw-er. A thermometer accurately reflects thetemperature at the coolest point insidethe server. This safety feature helpsensure that food products are being heldat a temperature above the bacterialgrowth level, and at temperatures belowthose that may over cook or dry out foodproduct.
CapacityUnit is designed to hold precooked foodsat serving temperature. Ideal for bakedpotatoes, vegetables, ribs, buns androlls. Each drawer holds one 12” x 20” x5” deep pan. Nominal capacities perdrawer:• 40 Baked Potatoes (120 count)• 8 #10 Cans Vegetables• 30 lb. Ribs• 6
1⁄2 doz. Hamburger Buns
• 7 doz. Dinner Rolls
Agency DataHot Food Servers are Underwriters’Laboratories, Inc. listed; NSF and CanadianStandards Association* certified.*CSA listed models are available throughCanadian Distributors only.
No Quibble WarrantyWarranty includes one year parts andlabor, on-site service. (U.S.A. only).
Ordering Information❒ 3A80A - 120V, 1 phase only❒ 3A80A - 208/240V, 1 phase only❒ 3B80A - 120V, 1 phase only❒ 3B80A - 208/240V, 1 phase only❒ 3C80A - 120V, 1 phase only❒ 3C80A - 208/240V, 1 phase only❑ ACCPANALL - extra pans for 80 series ❑ ACRK3B - Drawer Rack❑ ACC3B84GRTE - Grate❑ ACFB201 - Perforated Pan
Foodservice EquipmentJob_________ Item#_________
Hot Food ServersBuilt In Models 3A80A, 3B80A & 3C80A
A MIDDLEBY COMPANY1400 Toastmaster DriveElgin, Illinois 60120 USA1-800-323-2210 • Fax: 1-800-635-4725www.middleby.com
Form 203
3A80A 3B80A 3C80ACONNECTED LOAD AND ELECTRICAL DATA
MODELTOTAL kW NOMINAL AMPERES 1-PHASE
120V 208V 230V 240V 120V 208V 230V 240V
3A80A .45 .40 .47 .54 3.91 1.97 1.96 1.96
3B80A 1.00 .90 1.00 1.2 8.70 4.33 4.35 4.33
3C80A 1.35 1.2 1.35 1.6 11.74 5.87 5.87 5.88
1400 Toastmaster Drive, Elgin, IL 60120-9272 USA • 1-800-323-2210 • Fax: 1-800-635-4725www.middleby.com
Printed in U.S.A. 10/99 Form 203
INTENDED FOR COMMERCIAL USE ONLY. NOT FOR HOUSEHOLD USE.Toastmaster, in line with its policy to continually improve its products, reserves the right to change materials orspecifications without notice. Such revisions do not entitle the buyer to corresponding changes, improvements,
additions, or replacements for previously purchased equipment.
NOTE: All Figures In Parentheses Are In Millimeters.
Hot Food ServersBuilt In Models3A80A, 3B80A & 3C80A
DIMENSION AND PREHEAT DATA
MODELBODY DIMENSIONS DRAWER DIMENSIONS PREHEAT TIME IN MINUTES WEIGHTS
WIDE DEEP HIGH LONG WIDE DEEP 150°F 175°F INSTALLED SHIPPING
3A80A 29.1875" 19.2187" 10.875" 13.4375" 22.5625" 5.25" 18.8 26.2 72 84(741.3625) (488.1549) (276.225) (341.3125) (573.0875) (133.35)
3B80A 29.1875" 19.2187" 21.75" 13.4375" 22.5625" 5.25" 18.8 26.2 125 144(741.3525) (488.1549) (552.45) (341.3125) (573.0875) (133.35)
3C80A 29.1875" 19.2187" 29.3125" 13.4375" 22.5625" 5.25" 20.6 28.2 171 186(741.3625) (488.1549) (744.5375) (341.3125) (573.0875) (133.35)
ITEM NO.: 253 QUANTITY: 1
DESCRIPTION: PRODUCT HOLDING CABINET
MANUFACTURER: DUKE
MODEL: FWM3-22CF5-120
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 6.7 AMPS, 0.80 KW, 120V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Approval Stamp(s):
SpecificationsF.O.B Sedalia, Missouri 65301
OPTIONS:
□ Interchangable plastic lids designed for product flexibility □ Amber pans allows for visibility to easily check on inventory status □ 2-1/2” deep pans □ Single or double handled pans
AGENCY LISTING:
PRODUCT INFORMATION:PROJECT: ____________________________ITEM: ____________________________QUANTITY: ____________________________
MODEL:Product Holding Unit - FWM
■ FWM3-13 1 down, 3 across ■ FWM3-14 1 down, 4 across ■ FWM3-21 2 down, 1 across ■ FWM3-22 2 down, 2 across ■ FWM3-23 2 down, 3 across ■ FWM3-24 2 down, 4 across ■ FWM3-42 4 down, 2 across ■ FWM3-51 5 down, 1 across
BODY: ■ Stainless Steel Exterior construction for durability and ease of
construction ■ Annodized aluminum surface, durable and easily cleaned ■ Fully radiused curved corners that are easily cleaned ■ No removable parts or screws or fasteners to clean around ■ Cool to the touch thermoplastic front panel ■ Interchangable plastic lids designed for product flexibility ■ Amber pans allows for visibility to easily check on inventory status
HEATING: ■ Flexible 300 Watt heaters for 208/ 230/ 240 volt ■ Flexible 200 Watt heaters for 120 volt ■ Individually controlled rows for customized heating solutions ■ Quick heat up appoximately 15 minutes
CONTROLS ■ Ability to control different day parts ■ Web based programming ■ Upload programs through USB port no manager reprogramming
necessary ■ Automatic Pan linkability for product freshness ■ Timer to ensure no expired product is to be served ■ Simplistic system makes it easy for employees to use and
easy to manage ■ Alphanumeric displays are easy to read
SHORT FORM SPECIFICATIONS:Duke Product Holding Units - Thermostatically controlled heaters surround extruded aluminum for consistent heating of pre-cooked food. Body shall be constructed of stainless steel with cool-to-touch thermostatic front panel. Interchangeable, high-temperature lids control the product environment. Alphanumeric displays and web based programming track product hold times and temperatures.
PRODUCT HOLDING UNIT - Catalog No. FW
M3A.I.A. File No. 35-C-13
DUKE MANUFACTURING CO.2305 N. Broadway St. Louis, MO 63102
800.735.3853 Toll Free314.231.5074 Faxwww.dukemfg.com
PHU-01
FWM-22
Cata
log
No. P
HU -
FWM3
A.I.A
. File
No.
35-
C-13 PRODUCT HOLDING UNIT
Model
Height Width Depth Pan Size Cubeft.
crated
Crated ShipWeight
in. cm in. cm in. cmL W H
lbs. kgin. cm in. cm in. cmFWM3-13 7 17.8 29 73.7 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 8.3 75 34.1
FWM3-14 7 17.8 37 94 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 10.2 111 50.5
FWM3-21 12 30.5 14 35.6 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 3.4 67 30.5
FWM3-22 12 30.5 21 53.3 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 6.6 91 41.4
FWM3-23 12 30.5 29 73.7 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 8.3 113 51.4
FWM3-24 12 30.5 37 94.0 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 10.2 141 64.1
FWM3-42 22 55.9 21 53.3 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 7.9 145 65.9
FWM3-51 27 68.6 14 35.6 16 40.2 12.7 42.4 6.9 17.5 2.5 5.1 8.5 125 56.8
DIMENSIONS:
ELECTRICAL SPECIFICATIONS:
Model 100 Volt - HZ 50/60 120 Volt - HZ 50/60 208 Volt - HZ 50/60 230 Volt - HZ 50/60 240 Volt - HZ 50/60
Watts Amps NEMA Watts Amps NEMA Watts Amps NEMA Watts Amps CEE Watts Amps NEMAFWM3-13 - - - 600 5.2 5-15P 900 4.3 6-15P 900 3.9 7/7 900 3.8 6-15P
FWM3-14 - - - 800 6.7 5-15P 1200 5.8 6-15P 1200 5.2 7/7 1200 5.0 6-15P
FWM3-21 600 6.0 5-15P 600 5.0 5-15P 600 2.9 6-15P 600 2.6 7/7 600 2.5 6-15P
FWM3-22 800 8.0 5-15P 800 6.7 5-15P 1200 5.8 6-15P 1200 5.2 7/7 1200 5.0 6-15P
FWM3-23 - - - 1200 10.0 5-15P 1800 8.7 6-15P 1800 7.8 7/7 1800 7.5 6-15P
FWM3-24 1600 16.0 5-15P 1600 13.3 5-15P 2400 11.5 6-15P 2400 10.4 7/7 2400 10.0 6-15P
FWM3-42 1600 16.0 5-15P 1600 13.3 5-15P 2400 11.5 6-15P 2400 10.4 7/7 2400 10.0 6-15P
FWM3-51 1000 10.0 5-20P 1000 8.3 5-15P 1500 7.2 6-15P 1500 6.5 7/7 1500 6.3 6-15P
DUKE MANUFACTURING CO.2305 N. Broadway St. Louis, MO 63102
800.735.3853 Toll Free314.231.5074 Faxwww.dukmfg.com
FREIGHT CLASS: 100
Specification subject to change
05/09Printed in U.S.A
© 2009, Duke Manufacturing Co.
PROD
UCT
HOLD
ING
UNIT
- FW
M
■ FWM3-13 1 down, 3 across ■ FWM3-14 1 down, 4 across ■ FWM3-21 2 down, 1 across ■ FWM3-22 2 down, 2 across ■ FWM3-23 2 down, 3 across ■ FWM3-24 2 down, 4 across ■ FWM3-42 4 down, 2 across ■ FWM3-51 5 down, 1 across
Duke Manufacturing Company2305 N. Broadway • St. Louis, MO 63102
1-800-735-3853 • 314-231-1130 • 314-231-5074www.dukemfg.com
157949A
MOdeL FWM3-22Model No Shipping Weight
CratedVolts AC Amps Watts Hz
FWM3-22-100 91 lbs / 41.4 Kg 100 8.0 800 50/60
FWM3-22-120 91 lbs / 41.4 Kg 120 6.7 800 50/60
FWM3-22-208 91 lbs / 41.4 Kg 208 5.8 1200 50/60
FWM3-22-230 91 lbs / 41.4 Kg 230 5.2 1200 50/60
FWM3-22-240 91 lbs / 41.4 Kg 240 5.0 1200 50/60
ENDFRONT
TOP
11 3/4"29.7cm
[53]20 3/4" 15 7/8"
40.2cm
1 3/8”3.6 cm
2 3/4”6.9 cm
1 ”2.4 cm
Patent Info:US 6175099; US 6262394; US RE 40, 290;
SG 83896; CN ZL00805894.6; SK 0509521; EP 1164852; CA 2,367,679Other U.S. and Foreign Patents Pending
Duke Manufacturing Company2305 N. Broadway • St. Louis, MO 63102
1-800-735-3853 • 314-231-1130 • 314-231-5074www.dukemfg.com
157949A
MOdeL FWM3-22Model No Shipping Weight
CratedVolts AC Amps Watts Hz
FWM3-22-100 91 lbs / 41.4 Kg 100 8.0 800 50/60
FWM3-22-120 91 lbs / 41.4 Kg 120 6.7 800 50/60
FWM3-22-208 91 lbs / 41.4 Kg 208 5.8 1200 50/60
FWM3-22-230 91 lbs / 41.4 Kg 230 5.2 1200 50/60
FWM3-22-240 91 lbs / 41.4 Kg 240 5.0 1200 50/60
ENDFRONT
TOP
11 3/4"29.7cm
[53]20 3/4" 15 7/8"
40.2cm
1 3/8”3.6 cm
2 3/4”6.9 cm
1 ”2.4 cm
Patent Info:US 6175099; US 6262394; US RE 40, 290;
SG 83896; CN ZL00805894.6; SK 0509521; EP 1164852; CA 2,367,679Other U.S. and Foreign Patents Pending
Duke Manufacturing Company2305 N. Broadway • St. Louis, MO 63102
1-800-735-3853 • 314-231-1130 • 314-231-5074www.dukemfg.com
157949A
MOdeL FWM3-22Model No Shipping Weight
CratedVolts AC Amps Watts Hz
FWM3-22-100 91 lbs / 41.4 Kg 100 8.0 800 50/60
FWM3-22-120 91 lbs / 41.4 Kg 120 6.7 800 50/60
FWM3-22-208 91 lbs / 41.4 Kg 208 5.8 1200 50/60
FWM3-22-230 91 lbs / 41.4 Kg 230 5.2 1200 50/60
FWM3-22-240 91 lbs / 41.4 Kg 240 5.0 1200 50/60
ENDFRONT
TOP
11 3/4"29.7cm
[53]20 3/4" 15 7/8"
40.2cm
1 3/8”3.6 cm
2 3/4”6.9 cm
1 ”2.4 cm
Patent Info:US 6175099; US 6262394; US RE 40, 290;
SG 83896; CN ZL00805894.6; SK 0509521; EP 1164852; CA 2,367,679Other U.S. and Foreign Patents Pending
FRONT SIDE
ITEM NO.: 254 QUANTITY: 1
DESCRIPTION: TIMER
MANUFACTURER: INTEGRATED CONTROL
MODEL: 990925
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 120V, PLUG PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Wash MinderTMTemp MinderTM
Kitchen Minder TMProduct Quality TimersTM
Product ManagementTime Hygiene Temperature Integrated Control Corp.
748 Park Avenue Huntington, NY 11743 1.877.ICC.8788 www.goicc.com
TM
®
Chik�fil�A Timer SPECIFICATIONS
Timer Dimensions: 7.5” x 11.3125” x 1.0625 “ Bracket Dimensions: 5” x 2.25” x 2.25 “
Power Requirements: 100-240 V~0.5A Max, 50-60Hz. +12V _ _ _ 1.25 A
Complete shipment includes: Chik-fil-A Timer, Power Supply, Mounting Bracket, ICC Chik-fil-A Timer Quick Start Guide, Programming Instructions , Timer labels, screws and other mounting supplies.
Shipment weighs approximately 3.8 lbs.
Chick-fil-A Timer
Chick-fil-A Timer
ContactTECHNICAL SUPPORT
ICC provides an 12-month factory warranty for the Chick-Fil-A Timer. If a user detects a problem, a call is made to the ICC Hot-line. If an ICC technician determines that hardware must be replaced, ICC will ship a replacement component to the restaurant via overnight delivery.
WARRANTY
For technical support please contact our customer service manager:
John Patti [email protected]: 1.877.ICC.8788 Ex. 325 Fax: 631. 673.6756www.goicc.com
Mounting Bracket
Power Supply Install Accessories
User Manuals & Labels
ITEM NO.: 255 QUANTITY: 2
DESCRIPTION: FRENCH FRYER
MANUFACTURER: HENNY PENNY
MODEL: OFE321.02
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 61 AMPS, 14.4 KW, 208V, 3 PHASE, DIRECT PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
© 2008 Henny Penny Corporation, Eaton, OH 45320 USA 06/08/09
PROJECT QUANTITY ITEM NO
General Information Henny Penny open fryers offer high-
volume frying with programmable operation, oil management functions and fast, easy filtration.
The OFE-321 open fryer is available with a full vat or a split vat configuration. The split vat choice allows you to fry different products in completely separate environments at the same time—a great way to multiply your profits with one fryer.
Henny Penny 320 series open fryers recover temperature very quickly and have earned the ENERGY STAR® mark for energy efficiency. Fast recovery translates into higher throughput, lower energy costs and longer frying oil life.
A built-in filtration system filters and returns hot frying oil in less than four minutes, with no separate pumps or
Single-well split-vat open fryer model OFE-321 with COMPUTRON™ 1000 control
Henny Penny CorporationPO Box 60 Eaton OH 45320 USA
+1 937 456.8400 800 417.8417 +1 937 456.8434 Fax 800 417.8434 Fax
www.hennypenny.com
Standard Features • Stainless steel construction for
easy-cleaning and long life. • Heavy-duty stainless steel
rectangular fry pot with 7-year warranty.
• COMPUTRON™ 8000 control (additional charge.) 12 programmable cook cycles Melt mode Idle mode Load compensation Proportional control Optional filter prompt and customizable filter tracking
Clean-out mode. 16-character digital display with multiple language settings.
• Split vat model available.
• COMPUTRON™ 1000 simple digital control. ▪ Programmable ▪ LED Time/Temp display ▪ Simple UP/DOWN arrows
• Built-in filtration (additional charge.)• Easy basket set and release. • Specially designed cold zone
prevents scorching. • 4 heavy-duty casters, 2 locking.
Accessories shipped with unit • Fry baskets—please select one
1 full basket 2 half baskets
• 1 basket support for each vat
Accessories and options available separately
Direct Connect shortening disposal (filtration equipped units, only)
Shortening shuttle Filter rinse hose Fry well cover
APPROVED APPROVED AS NOTED RESUBMIT
AUTHORIZED SIGNATURE DATE
pans required. Frequent filtering extends frying oil life, improves product quality and reduces oil costs.
The OFE-321 electric open fryer features Henny Penny’s heavy-duty stainless steel rectangular fry pot that promotes fast even cooking and comes with a 7-year warranty—the best in the business.
The COMPUTRON™ 8000 control provides fully automatic, programmable operation, as well as energy-saving, filtration and cook management features.
The COMPUTRON™ 1000 control offers programmability in a simple, easy to use digital control panel with LED display.
Open fryers MODEL OFE-321 electric
© 2008 Henny Penny Corporation, Eaton, OH 45320 USA 06/08/09
Continuing product improvement may subject specifications to change without notice.
PROJECT ITEM NO
www.hennypenny.com
MODEL OFE-321 electric
Open fryers
17 3/8 in. (441 mm)
37 3/8 in. (949 mm)
44 in. (1118 mm)
Dimensions Width 17 3/8 in. (441 mm) Depth 37 3/8 in. (949 mm) Height 44 in. (1118 mm)
Required clearances Sides: 6 in. (152 mm) air flow Back: 6 in. (152 mm) air flow, connections Front: 30 in. (762 mm) filter pan removal
Crated dimensions Length 40 in. (1016 mm) Depth 25 in. (635 mm) Height 52 3/4 in. (1340 mm) Volume 30.5 cu. ft. (0.86 m³)
Net weight N/A Crated weight: 281 lbs. (128 kg)
Heating Immersed elements Max output:14.4 kW
PLAN
FRONT
Electrical connection
Bidding Specifications • Provide Henny Penny model OFE-321
single-well electric open fryer with available built-in filtration system (additional charge.)
• Units can be ordered with full or split vat. • Units shall incorporate either
COMPUTRON™1000 simple digital controls or COMPUTRON™ 8000 control system (additional charge.)
• Materials—cabinet, deck, exhaust stack, filter drain pan and various fittings are stainless steel. Fry pots are heavy duty stainless steel.
• Units qualify for the ENERGY STAR® mark. • Immersed fixed heating elements provide for
a “cold zone” that extends oil life. • Unit’s controller provides for programmable
or manual operation with press-key controls and LED digital display. COMPUTRON™ 8000 control offers idle and melt modes, load compensation, filtration tracking and 7-day history.
• Units will include 4 heavy-duty casters, 2 locking.
• Units with filtration system ship with stainless steel Max filtration screen and 2 PHT filter envelopes. All units ship with choice of full basket or 2 half baskets.
Amps Volts Phase Cycle/Hz Watts Full vat Split vat
Wire
208 3 60 14400 39.9 38.9 3+G
220-240 3 50/60 14400 37.2 3+G
240 3 60 14400 37.2 33.7 3+G
380-415 3 50/60 14400 21.7 3NG
400 3 50-60 14400 20.9 20.4 3NG
480 3 60 14400 17.5 3+G
NOTE: Power cord and plug must be installed on site by a qualified electrician.
Laboratory certifications Oil capacity Full vat: 32 qts. or 65 lbs. (30.3 l or 30 kg)
Split vat: 12.4 qts. or 25 lbs. (11.7 l or 11.4 kg)
Electrical
ITEM NO.: 256 QUANTITY: 3
DESCRIPTION: PRESSURE FRYER
MANUFACTURER: HENNY PENNY
MODEL: PFE500.02
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 38 AMPS, 13.5 KW, 208V, 3 PHASE, NEMA 5-50R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
MODEL PFE-500 Electric
© 2006 Henny Penny Corporation, Eaton, OH 45320 USA Revised 11/11/09
PROJECT QUANTITY ITEM NO
General Information Henny Penny first introduced
commercial pressure frying to the foodservice industry 50 years ago. Today, Henny Penny pressure fryers continue to lead the industry in performance, durability and innovation.
Frying under pressure enables lower cooking temperatures and faster cooking times. The additional pressure also helps seal in the food’s natural juices and reduce absorption of frying oil into product. Results of pressure frying generally produce a product with less fat and more original flavor than other methods of frying.
Henny Penny pressure fryers incorporate several beneficial design features, including rectangular fry pot, cold-zone, color-keyed locking spindle, heavy duty lid hinge, raised edge on fryer deck and more.
PFE-500 4-head electric pressure fryer with COMPUTRON™ 8000 control.
Pressure fryers
Standard Features • Stainless steel cabinet for easy-
cleaning and long life. • Heavy-duty stainless steel
rectangular fry pot with 7 year guarantee.
• Cast aluminum alloy lid is strong but light for easy handling.
• Color-keyed locking spindle engages pressure seal.
• Patented lid-lock system keeps lid locked until pressure reaches 1 psi.
• Built-in filtration. • Raised edge on deck reduces
spills. • Channel under lid helps direct
condensation away from pot when lid is open.
• 4 heavy-duty casters, 2 locking.
• COMPUTRON™ 8000 control (additional charge.) 12 programmable cook cycles Melt mode Idle mode Load compensation Proportional control Optional filter prompt and customizable filter tracking
Clean-out mode. 16-character digital display with multiple language settings.
• COMPUTRON™ 1000 simple digital control. Programmable LED Time/Temp display Simple UP/DOWN arrows
Accessories shipped with unit Max shortening filtration system with choice of standard filtration media:
2 Carbon filter pads 2 Non-woven carbon filter envelopes
2 PHT filter envelopes
Accessories and options available separately
Direct Connect shortening disposal 4-tiered basket Locking basket handle Full-size basket and handle Crumb pan and handle Carbon pad envelope filter media Filter rinse hose attachment Filter pan dolly
The PFE-500 features choice of low or high wattage immersed heating elements. Henny Penny’s high-efficiency heat exchange system produces among the lowest average exhaust gas temperatures in the industry, so you get fast recovery and energy savings. A narrow five square foot footprint also saves floor space and cookline frontage.
Built-in filtration system filters and returns hot oil in less than four minutes with no extra pumps or pans and no handling of hot oil.
The COMPUTRON™ 8000 control provides fully automatic, programmable operation, as well as energy-saving, filtration and cook management features.
The COMPUTRON™ 1000 control offers programmability in a simple, easy to use digital control panel with LED display.
APPROVED APPROVED AS NOTED RESUBMIT
AUTHORIZED SIGNATURE DATE
© 2006 Henny Penny Corporation, Eaton, OH 45320 USA Revised 11/11/09
Laboratory certifications
PROJECT ITEM NO
19 1/8 in. (486 mm) 38 7/8 in. (968 mm)
Capacity Product 14 lbs. (6.4 kg) Oil 48 lbs. (22.4 l)
Electrical
FRONT
PLAN
Dimensions Height: 48 in. (1219 mm) Width: 19 1/8 in. (486 mm) Depth: 38 7/8 in. (968 mm)
Required clearances Top: 16 in. (400 mm) for lid up Sides: 6 in. (152 mm) air flow Back: 6 in. (152 mm) air flow Front: 30 in. (762 mm) filter pan removal
Crated dimensions Length: 44 1/2 in. (1130 mm) Depth: 21 3/4 in. (550 mm) Height: 56 in. (1420 mm) Volume: 31.4 cu. ft. (0.88 m³)
Net weight N/A Crated weight: 325 lbs. (148 kg)
Pressure Operating pressure: 12 psi. Safety valve setting: 14.5 psi.
Heating 3 immersed elements
3750W each (11250W total) 4500W each (13500W total)
Pressure fryers
48 in. (1219 mm)
MODEL PFE-500 Electric
Amps Volts Phase Cycle/Hz
11250W 13500W Wire
190-208 1 50 or 60 54.0 65.0 2+G 190-208 3 50 or 60 32.0 38.0 3+G 208 1 60 54.0 65.0 2+G 208 3 60 32.0 38.0 3+G 220-240 1 50 or 60 52.0 58.0 2+G 220-240 3 50 or 60 30.0 33.0 3+G 220/380 3 50 or 60 17.1 20.5 4+G 240/415 3 50 or 60 18.6 18.8 4+G 380-415 3 50 17.1 18.8 3NG 480 3 60 14.0 16.0 3+G
Optional power cord and plug can be supplied for 3 phase 208V and 220-240V units, only.
Plug type: NEMA 15-50 P
G X
Z Y
Bidding Specifications • Provide Henny Penny Model PFE-500
electric pressure fryer, 15 lbs. (6.4 kg) capacity per load, and built-in filtration system (additional charge.)
• Units shall incorporate either COMPUTRON™1000 simple digital controls or COMPUTRON™ 8000 control system (additional charge.)
• Materials—cabinet, deck, exhaust stack,
spindle, locking mechanism, filter drain pan and various fittings are stainless steel. Fry pot is heavy duty stainless steel. Lid is aluminum alloy.
• Color-keyed locking spindle and lid-lock mechanism engage pressure seal to create 9 psi pressure in cooking chamber.
• Three low-wattage electric elements encircle the inside of the fry pot part-way up the side, and are not located on the bottom or below
the pot. This design produces a “cold zone” that extends suitable oil life.
• Unit’s controller provides for programmable or manual operation with press-key controls and LED digital display. COMPUTRON™ 8000 controloffers idle and melt modes, load compensation, filtration tracking and 7-day history.
• Units will include 4 heavy-duty casters, 2 locking. • Units will be shipped with starter kit of choice of
filtering media.
Electric power
Continuing product improvement may subject specifications to change without notice.
Henny Penny CorporationPO Box 60 Eaton OH 45320 USA
+1 937 456.8400 800 417.8417 +1 937 456.8434 Fax 800 417.8434 Fax
www.hennypenny.com
ITEM NO.: 257 QUANTITY: 1
DESCRIPTION: CHARGRILL
MANUFACTURER: TAYLOR
MODEL: QS-11
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 27 AMPS, 9.6 208V, 3 PHASE, PLUG, NEMA 15-20R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Rockton, Illinois 61072800-255-0626Phone 815-624-8333 Fax 815-624-8000www.taylor-company.come-mail: [email protected]
International OfficeTaylor Company S.r.l.Roma, ItalyTel: +39-06-420-12002 Fax: +39-06-420-12034e-mail: [email protected]
QS11
Item No. _______________________________
QS11
Cook-to-order menu items are served FAST!! With theoptional platen lowered, the top and bottom of the productare cooked simultaneously. Foods maintain natural juiciness,and your customers are served food hot off the grill, in lessthan half the time of standard grills.
Even temperatures across the entire cooking surface assuressafe product integrity and fast recovery. Holding cooked foodproducts for busy times is virtually unnecessary, reducingproduct waste. Multiple grills may be installed side-by-sideto increase cooking surface and capacities.
Lower Cooking Surface One, 12” (305 mm) wide, by 24” (610 mm) deep cooking zone withthree independently controlled heating elements. Assures eventemperatures and quick recovery.
Controls Programmable microprocessor controls make menu selectionsimple. Includes a self-diagnostic feature for serviceability. Clearplastic door protects control from splashes or spills. Separatedurable start button is provided to activate cooking cycle.
Temperature Control Grill surface temperature may be set from 150 to 400ºF (65 to205ºC). Optional upper platen temperature may be set from 150 to425ºF (65 to 218ºC).
Indicator LightsLights illuminate when heaters are on.
Features
Electric Grill
Shown with optional features: grooved lower cooking surface and
grooved upper platen
Optional grooved lower cookingsurface and/or grooved upper
platen
QS11
QS11Electric Grill
32(813)
COOKINGSURFACE
32(813)
COOKINGSURFACE
26(661)
COOKINGSURFACE
26(661)
COOKINGSURFACE
31-7/16 (799)31-7/16 (799)
5(127)
5(127)
36-5/32 (918)36-5/32 (918)
59-11/16(1516)
59-11/16(1516)
11-1/8(283)11-1/8(283)
9-3/4 (248)9-3/4 (248)
12-9/16 (319)12-9/16 (319)
30 -60° °30 -60° °
1-3/16 (30)1-3/16 (30)2-3/4 (70)2-3/4 (70)
1/(13)1/(13)
2
24 (609.6)DEEP COOK SURFACE
24 (609.6)DEEP COOK SURFACE
NOTE: FIGURES IN PARENTHESES INDICATE MILLIMETERS.NOTE: FIGURES IN PARENTHESES INDICATE MILLIMETERS.
38-3/8(975)38-3/8(975)
39-1/2 (1003)39-1/2 (1003)
Electrical One dedicated electrical connection is required. See the Electrical chart forthe proper electrical requirements.
ClearanceGrill clearance must be maintained at least 3” (76 mm) from all combustiblematerials, and 3” (76 mm) of air clearance in the rear.
Taylor Company, a division of Carrier Commercial Refrigeration, Inc.Rockton, Illinois 61072815-624-8333 800-255-0626 Fax 815-624-8000www.taylor-company.com
Printed in U.S.A.
Electrical Total Maximum Minimum Poles (P) Amps Fuse Size Circuit Ampacity Wires (W)208/60/3 27 50 28 3P 4W
This unit may be manufactured in other electrical characteristics. Refer to the local Taylor Distributor for availability. (For exact electrical information, always refer to the data label of the unit.)
Weights lbs. kgs.Net 440 199.6Crated 523 237.2
cu. ft. cu. m.Volume 32.6 0.92
Dimensions in. mm.Width 12-9/16 319Depth 39-1/2 1003Height 38-3/8 975Counter Clearance 5 127*Mounted on standard casters
��Grease Tray Drain��Grooved Lower Cooking Surface��Upper Platen, Grooved Cooking Surface ��Upper Platen, Smooth Cooking Surface ��Utility box for grill scraper & release sheet wiper
Upper Platen The upper platen has a cooking surface of 11” X 20” (279 X 508 mm) withthree individually controlled heaters. An infinite gap adjustment willaccommodate varying product thicknesses from zero to 7/8” (22 mm).
Release Material Completely covers and protects upper platen surface, prevents product fromsticking and minimizes carbon build-up. Attachment method ensures that therelease material stays in place throughout the day for easy cleaning.
Options
Specifications
057930—ADV 01/03
Continuing research results in steady improvements; therefore, thesespecifications are subject to change without notice.
Bidding SpecsElectrical: Volt ___________________ Hz__________ ph _________
Neutral: �� Yes ��No
Options:__________________________________________________________________________________________________________
ITEM NO.: 263 QUANTITY: 1
DESCRIPTION: CONVECTION OVEN
MANUFACTURER: LANG
MODEL: 9PR30CAPF208 CF
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 57.6 AMPS, 19.8 KW, 208V, 3 PHASE, DIRECT WIRE PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: FULL GRIDDLE TOP HGD LEFT PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
LANG MANUFACTURING - A DIVISION OF STAR MANUFACTURING INT’L, INC. • 10 SUNNEN DR. ST. LOUIS, MO 63143
TOLL FREE: 800.264-7827 • FAX: 314-781-3636 • www.langworld.com
Item No.
Project
Quantity
30” Electric Range with Convection Oven Base Model: R30C Series
CONSTRUCTION FEATURES• One piece heavy duty 430 Series stainless steel exterior, with attractive
No. 4 finish
• Cooking compartment is 430 Series stainless steel
• 2” insulation on six sides of cooking compartment
• Heavy duty compartment door, with large double pane tempered glass window
• Powerful blower centered on side of compartment
• Nine position oven rack slide supports
• Five chrome-plated oven racks provided
• 4” swivel casters standard
• 1” high range–top back stop
• 2-3/4” wide full width front grease trough
• Grease drain in trough with full width & depth spillage drawers
• Griddle configurations include a one piece splash guard, back & sides
PERFORMANCE FEATURES• Compact 30” wide range incorporates half-size convection oven with five
13 X 18” pan capacity
• 150 to 450 F oven operating temperature range
• Solid state oven temperature control accurate to 4 F
• Two speed fan with fan pulse capability
• Door interlock switch cuts power to fan
• Choice of cook top configurations, to include:❏ 4 ea. 8” diameter French Plates
❏ 2 ea. 8” diameter French Plates and 1 ea. 12” wide Hot Top
❏ 2 ea. 12” wide Hot Tops❏ 18” wide 1/2” thick Griddle and 2 ea. 8” diameter French Plates
❏ 18” wide 1/2” thick Griddle and 1 ea. 12” wide Hot Plate
• Full front grease trough, grease drain & spillage drawers speed cleanup
• Separate, independent controls allows simultaneous multi-function cooking
CONTROLS [For Oven] CHOICE OF:❏ Accu-Plus™ Control [-AP]
• Simple knob-set time and temperature controls
• 1-hour timer with non-stop buzzer
• Pulse-fan switch• HIGH-LOW speed fan switch
• Power-ON switch
❏ Platinum Control [-PT]
• Solid state, icon driven, one-touch programmable controls• Up to 99 product programs, with multiple baking tiers
• Time, temperature, heat loss and adjustable shelf compensation
• Cook-n-Hold programming• 2-speed fan & variable-rate pulse-fan control
• PC link programming
• Power-ON switch
❏ Range controls vary by top configuration and will include:[-APA] Four 6-heat level switches [ea. French Plate]
[-APB] One thermostat for Hot Plate & Two 6-heat level switches [ea. French Plate]
[-APC Two thermostats, one for each Hot Plate
[-APD] One thermostat for 18” Griddle & two 6-heat level switches
[ea. French Plate]
[-APE] One thermostat for 18” Griddle & one thermostat for the Hot Plate
SHORT/BID SPECIFICATIONRange shall be a LANG Manufacturing Model R30C___ [Specify one]:
-APA, with 4 ea. 8” diameter French Plates;
-APB, with 1 ea.12” x 24” x 1/4” thick Hot Plate and 2 ea. 8”
diameter French Plates;
-APC, with 2 ea. 12” x 24” x 3/4” thick Hot Plate;
-APD, with 18” wide Griddle and 2 ea. 8” diameter French Plates;
- A P E, with 18” wide Griddle and 1 ea. 12” x 24” x 3/4” thick Hot
P l a t e ;
A 30” wide heavy duty electric heated unit with five half size pan
capacity convection oven base and 15.6-16.8-kW total power
input; all stainless steel exterior; fully insulated oven with
stainless steel interior, heavy duty door hinged left, with double
pane viewing window and five chrome plated oven rack standard;
choice of: -AP [solid state knob-set] or –PT [touch-pad
programmable] oven controls, with individual cook-top
component controls; plus all the features listed and
options/accessories checked:
STANDARD PRODUCT WARRANTY• One year, parts & labor
• Lifetime warranty on oven door mechanism
Sheet No. LSP-R8 (rev. 06/07)
Model R30C-APD shown
LANG MANUFACTURING - A DIVISION OF STAR MANUFACTURING INT’L, INC. • 10 SUNNEN DR. ST. LOUIS, MO 63143
TOLL FREE: 800.264-7827 • FAX: 314-781-3636 • www.langworld.com
© 2005 Lang Manufacturing Company Printed in U.S.A. 9/05-M-13852
Due to continuous improvements, specifications subject to change without notice. Sheet No. LSP-RS (rev. 06/07)
[Front View/Elevation] [Right Side View] [Top View/Plan]
30” Electric Range with Convection Oven Base Model: R30C Series
CAD SYMBOLS & PRICING
Model Has: R30C-APA R30C-APB R30C-APC R30C-APD R30C-APE
Oven Base: Convection Convection Convection Convection Convection
Griddle: - - - 18” wide 18” wide
French Plates: 4 each 2 each - 2 each
Hot Plates: - 1 each 2 each 1 each
Pictogram:[Unit Top View]
CONFIGURATION GUIDE
Model Height x Width x Depth Clearance from Weight Freight(With standard legs) combustible surface Actual Shipping Class
R30C_32” x 30.2” x 30” Sides: 3” (77mm) 362* lbs. 412* lbs.
85812.8mm x 766mm x 762mm Back: 3” (77mm) 165 kg 187 kg
* Depending on configuration.
ModelE Electrical Requirements
Voltage Total kW Phase Amps/Line
208V/60Hz 19.8 1 95.2
240V/60Hz 19.8 1 82.5
R30C_ 208V/60Hz 19.8 3 57.6
240V/60Hz 19.8 3 50.0
480V/60Hz 19.8 3 25.0
OPTIONS & ACCESSORIES
❏ Grooving on [1” thick ONLY] Range Griddle Plate
❏ 480 Volt, 3-phase model
❏ Extra wire pan rack [Five provided as std.]
INSTALLATION REQUIREMENTS
• Unit is shipped in one piece
• E Single 208/240V, 1/ 3-Phase; or 480V, 3-phase electrical connection
• Installation under approved vent hood required. Consult local codes.
[Power connection from bottom. See below]
ITEM NO.: 272 QUANTITY: 1
DESCRIPTION: MIXER – TABLE TOP MODEL
MANUFACTURER: HOBART/TRAULSEN
MODEL: HL200
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 8 AMPS, ½ HP, 115V, 1 PHASE, PLUG PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 11400
F-40089 – Legacy™ HL200 Mixer Page 1 of 4
LEGACY™
HL200 MIXER701 S Ridge Avenue, Troy, OH 453741-888-4HOBART • www.hobartcorp.com
LEG
AC
Y™ H
L200 MIX
ER
STANDARD FEATURES
■ Heavy-Duty 1⁄2 H.P. Motor
■ Gear Transmission
■ Three Fixed Speeds Plus Stir Speed
■ Shift-on-the-Fly™ Controls
■ Patented soft start Agitation Technology
■ 15-Minute SmartTimer™
■ Automatic Time Recall
■ Large, Easy-To-Reach Controls
■ Single Point Bowl Installation
■ Ergonomic Swing-Out Bowl
■ #12 Taper Attachment Hub
■ Open Base
■ Stainless Steel Bowl Guard
■ Metallic Gray Hybrid Powder Coat Finish
ACCESSORY PACKAGES - featuring Hobart Quick Release™ Agitators
❑ Deluxe Accessory Package Includes: - 20 Quart Stainless Steel Bowl - 20 Quart “B” Beater - 20 Quart “D” Wire Whip - 20 Quart Bowl Scraper - 20 Quart Ingredient Chute
❑ Standard Accessory Package Includes: - 20 Quart Stainless Steel Bowl - 20 Quart “B” Beater - 20 Quart “D” Wire Whip
MODELS
❑ HL200 – 20-Quart All Purpose Mixer❑ HL200C – 20-Quart All Purpose Mixer with Maximum Security Correctional Package
OPTIONS
❑ SmartPlus2™ Programmable Recipe Timer
Specifications, Details and Dimensions on Inside and Back.
R
701 S Ridge Avenue, Troy, OH 453741-888-4HOBART • www.hobartcorp.com
LEGACY™
HL200 MIXER
Page 2 of 4 F-40089 – Legacy™ HL200 Mixer
SOLUTIONS/BENEFITS1⁄2 H.P. Motor Durability ■ Heavy-duty to meet the most demanding
operationsGear Transmission Durability, Reliability ■ Ensures consistent performance and minimum
downtime under heavy loadsThree Fixed Speeds plus Stir Speed Flexibility, Reliability, Consistency ■ For incorporating, blending, mixing ingredients ■ Supports consistent results and thorough mixingShift-on-the-Fly™ Controls Flexibility ■ Allows operator to change speeds while mixer is
runningPatented soft start Agitation Technology Sanitation ■ Each speed has a soft transition into a higher
speed to reduce the chances of product splash-out
15-Minute SmartTimer™ Convenience, Ease of Use, Consistency ■ Supports recipe mixing times ■ Provides accurate results and eliminates
overmixingAutomatic Time Recall Productivity, Consistency ■ Remembers the last time set for each speed ■ Great for multiple batchesErgonomic Swing-Out Bowl Ease of Use, Convenience ■ Easy loading and unloading of products ■ Single Point Bowl Installation allows for simple
mounting and removal of bowl ■ Bowl Interlock ensures mixer bowl is properly in
place for mixer to operateStainless Steel Bowl Guard Protection ■ Safety interlock prevents operation when front
portion of guard is out of positionHobart Accessories Durability, Flexibility, Simplicity ■ Hobart Quick Release™ agitators allow for
simple installation and removal from agitator shaft
■ Hobart accessories are designed for long-term usage under heavy-duty conditions
■ Large array of accessories provide multiple uses for recipe and product processing
HL200 MIXER CAPACITY CHART
Recommended Maximum Capacities - dough capaci-ties based on 70°F. water and 12% flour moisture.
AGITATORS PRODUCT SUITABLE FOR HL200 OPERATION CAPACITY OF BOWL (QTS. LIQUID) 20
Egg Whites D 1 qt.
Mashed Potatoes B & C 15 lbs.
Mayonnaise (Qts. of Oil) B or C or D 10 qts.
Meringue (Qts. of Water) D 11⁄2 pts.
Waffle or Hot Cake Batter B 8 qts.
Whipped Cream D or C 4 qts.
Cake, Angel Food (8-10 oz. cake) C or I 15
Cake, Box or Slab B or C 20 lbs.
Cake, Cup B or C 20 lbs.
Cake, Layer B or C 20 lbs.
Cake, Pound B 21 lbs.
Cake, Short (Sponge) C or I 15 lbs.
Cake, Sponge C or I 12 lbs.
Cookies, Sugar B 15 lbs.
Dough, Bread or Roll (Lt.-Med.) 60% AR § ED 25 lbs.■
Dough, Heavy Bread 55% AR § ED 15 lbs.■
Dough Pie B & P 18 lbs.
Dough, Thin Pizza 40% AR (max. mix time 5 min.) §‡ ED 9 lbs.■
Dough, Med. Pizza 50% AR §‡ ED 10 lbs.■
Dough, Thick Pizza 60% AR §‡ ED 20 lbs.■
Dough, Raised Donut 65% AR ED 9 lbs.*
Dough, Whole Wheat 70% AR ED 20 lbs.■
Eggs & Sugar for Sponge Cake B & C or I 8 lbs.
Icing, Fondant B 12 lbs.
Icing, Marshmallow C or I 2 lbs.
Shortening & Sugar, Creamed B 16 lbs.
Pasta, Basic Egg Noodle (max. mix time 5 min.) ED 5 lbs.
NOTE: % AR (% Absorption Ratio) - Water weight divided by flour weight. Capacity depends on moisture content of dough. Above capacities based on 12% flour moisture at 70°F water temperature.■ 1st Speed
* 2nd Speed
† 3rd Speed
§ If high gluten flour is used, reduce above dough batch size by 10%.
‡ 2nd Speed should never be used on 50% AR or lower products.
USE OF ICE REQUIRES A 10% REDUCTION IN BATCH SIZE.1 gallon of water weighs 8.33 lbs.
NOTE: Attachment hub should not be used while mixing.
LEGACY™
HL200 MIXER701 S Ridge Avenue, Troy, OH 453741-888-4HOBART • www.hobartcorp.com
F-40089 – Legacy™ HL200 Mixer Page 3 of 4
SPECIFICATIONS
MOTOR:1⁄2 H.P. high torque motor.
100-120/50/60/1 8.0 Amps 200-240/50/60/1 5.0 Amps
ELECTRICAL:100-120/50/60/1, 200-240/50/60/1 – UL Listed.
CONTROLS:Magnetic contactor with thermal overload protec-tion. Internally sealed “Start-Stop” push buttons. A 15-minute SmartTimer™ is standard. SmartTimer™ includes Automatic Time Recall, which remembers the last time set for each speed. Optional SmartPlus2™ Programmable Recipe Timer allows operators the ability to program up to 4 recipes with 5 steps per recipe. SmartPlus2™ automatically changes speeds and starts timer count-down without operator intervention.
TRANSMISSION:Gear-driven. Gears are constant mesh heat-treated hardened alloy steel along with anti-friction ball bearings. Grease lubricants furnished to all gears and shafts.
SPEEDS:
Agitator(RPM)
Attachment(RPM)
Stir 59 33
First (Low) 107 61
Second (Intermediate) 198 113
Third (High) 365 207
BOWL GUARD:Heavy-duty stainless steel wire front and solid rear portion. Front portion of guard rotates easily to add ingredients and install or remove agitator. It detaches in seconds for cleaning in dishwasher or sink. Rear portion of guard can be quickly cleaned in position. Guard must be in closed position before mixer will operate. Bowl support interlock provides further protection.
BOWL LIFT:Ergonomic style, hand crank operated, self-locking in top and bottom position.
FINISH:Metallic Gray Hybrid Powder Coat finish.
ATTACHMENT HUB:Comes with front-mounted Hobart standard #12 taper attachment hub for use with Hobart #12 size attachments.
ATTACHMENTS AND ACCESSORIES:The following are available at extra cost:
Stainless Steel Bowl“B” Flat Beater“C” Wing Whip“D” Wire Whip“E” Dough Hook“ED” Dough Hook“P” Pastry KnifeBowl Splash CoverBowl ScraperIngredient Chute12 Quart Accessories9" Vegetable SlicerMeat Chopper AttachmentRubber Foot PadsAttachment Tray Support
Listed by Underwriters Laboratories Inc. and certified by NSF International.
Hobart Bowl Scraper
Hobart Ingredient Chute
701 S Ridge Avenue, Troy, OH 453741-888-4HOBART • www.hobartcorp.com
Page 4 of 4 F-40089 – Legacy™ HL200 Mixer
As continued product improvement is a policy of Hobart, specifications are subject to change without notice.
Printed On Recycled Paper
LEGACY™
HL200 MIXER
F-40089 (REV. 7/05) LITHO IN U.S.A. (H-01)
SPECIFICATIONS
DETAILS AND DIMENSIONS
ELECTRICAL SPECIFICATIONS: 100-120/50/60/1, 200-240/50/60/1 – UL Listed.
WEIGHT: 189 lbs. net; 204 lbs. domestic shipping.
WARRANTY: Unit has full one-year warranty on parts, labor and mileage against manufacturer’s defects. Service contracts are available.
ITEM NO.: 283 QUANTITY: 6
DESCRIPTION: FULL HEIGHT MENU LIGHTBOX
MANUFACTURER: EXPOTRANS
MODEL: FH 3EXP031
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 0.55 AMPS, 120V, 1 PHASE, PLUG, NEMA 5-15R PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Mounting Option:
6561
19.63
8973
23.81
X YGraphic:
OD:
VO:
QTY: 66
Color:
Powder Coat RAL 3020
Plexi Glass:
X
X
X 20.63 24.81
19.13 23.31
Hinge Orientation:
Top
Lamps:
Cool White
F20T12 24
0
Qty:
Qty:
3
0
Ballast:
Qty:
Qty:
3
0
LC1420C
0
Voltage:
120vlts 60hz
Wattage:
60
Amperage:
0.55
Locks:
Allen
Angle Hanging Bracket
Quote No.:
SpecSheet No. :
*LI-S-S-B-HD
ANV
8/25/2004 10:16:05AM
1
Strategic Equip & Supply
Client Approval: Date:
Non Glare
Milk
1/8
1/16
*LI-S-S-B-HD
Strategic Equip & Supply
8/25/2004 10:16:05AM
ANV2
Power Placement:
Back Bottom Right
Quote No.: 6561
SpecSheet No. : 8973
Client Approval: Date:
J Box and Power Cord
ITEM NO.: 736 QUANTITY: 2
DESCRIPTION: MILKSHAKE SPINNERS
MANUFACTURER: HAMILTON BEACH
MODEL: HMD300M-220
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 1 AMP, 1/3 HP, 208V CONNECTS HARDWIRE TO ICE CREAM MACHINE PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
HMD300M-220Single Spindle Mixer for Machine Mounting
•Performance1/3 HP motor delivers all the exceptional mixing of the HMD200 •OperationPowers on through a pulse-switch located on the soft-serve ice cream machine. Two- speed sealed rocker switch controls mixing.•Precision MotorEach motor is individually balanced to minimize vibration. Built to last with sealed, permanently lubricated ball bearings.•DurableAll-metal, die cast construction offers durability in a smooth, rounded shape that is easy to clean. Vent-free housing design prevents contaminants from entering the housing and damaging the motor.•DimensionsLength: 6.75”, Width: 6.75”, Height: 19.75”•RatingsNSF, Approved for Commercial Use, 220V, 60Hz, 1A•Warranty1 Year Warranty. All service should be handled by calling Technical Services at 866-285-1087 (or 910-693-4277.)
6.75”
19.75”
6.75”
ITEM NO.: 738 QUANTITY: 1
DESCRIPTION: MILKSHAKE BASE DISPENSER
MANUFACTURER: KAN-PAK
MODEL: CDG211
CONDITIONS: [ X ] NEW EQUIPMENT [ ] EXISTING [ ] SPARE NUMBER [ ] TO BE FABRICATED [ ] NOT IN CONTRACT [ ] BY PURVEYOR [ X ] PROPRIETARY [ ] UTILITY REQUIREMENTS: ELECTRICAL: 3 AMPS, 120V, 1 PHASE, PLUG PLUMBING: VENTILATION: SUPPLEMENTAL INFORMATION: PROJECT: UNIVERSITY OF MARY HARDIN - BAYLOR PROJECT NO: 11092
Kan-Pak CDG 211 Series Liquid DispenserCDG Series liquid dispensers are cost-effective refrigerated liquid dispenser systems capable of dispensing up to two different bag-in-box products.
Features:• Simple product dispensing for various liquid products including milk, cream, cold coffee, juices and many more!
• Manual, lever operated dispensing system ensures maximum ‘up-time’ with no microprocessor issues
• Holds two 9.5 Litre/2.5 Gallon bag-in-box products for refrigerated dispensing
• Best value on the market delivering the fastest return on investment and maximum profitability
• Simple to install and easy to use - remove from carton and power the unit up …that’s all there is to it!
Specifications:• Dispenses two products. Manual, lever operated
• Capacity: 2 x 9.5 Litres/2 x 2.5 Gals
• Weight: 77 lbs
• Dimensions: 22” x 12” x 25 1/2” (L x W x H)
• A/C Supply Voltage: 120VAC/60Hz/1P/4Amp
• Refrigeration: Compressor cold wall evaporation; accurate to 32˚F / 0˚C
• Environmentally friendly 134A refrigerant. CFC-free
• Stainless steel construction with polyurethane insulation
• Shipping Dimensions: 27” x 17” x 30” (L x W x H) Shipping Weight: 84 lbs.
• CDG 211 is certified to NSF/ANSI Standard 20 and certified to UL 471 and CSA C22.2 No. 120
Kan-Pak LLC, 1016 South Summit, Arkansas City, Kansas, 67005
For more information, please contact usvia phone or email at 1-800-378-1265or [email protected] visit us on the web at www.kan-pak.com
Rev.
Feb/
10
CDG-
211
shee
t- P
art n
umbe
r: 50
-000
6-40