UNIVERSITI KUALA LUMPUR

Module TitleCodeStatusLevelCredit ValuePre-requisite

Assessment

LecturersSemester Taught

Objectives

Final Year ProjectPRJ 3016MajorDegree6 (0,0,6)-

Logbook 35%Presentation 30%Report 35%Total 100%

All Lecturers7&8The objectives of this subject for:

Semester 7 are

1. To guide students in identifying and choosing a suitable

title according to their level and specialization area.

project

2. To guide students in preparing the feasibility studies according to

the identified project.

3. To guide students in preparing their project/ technical

writing and project presentation.

Semester 8 are

1. To guide students in executing their proposed project.

2. To guide students in problem solving.

3. To guide students in preparing their final project/ technical

and project presentation.

report

report

Itt)

J&

UNIVERSITI KUALA LUMPUR

Learning Outcome

At the end of this course in :

Semester 7, students should be able to

1. Recognize the title and scope of research project

2. Identify and apply the methodologies to develop the research

project

3. Carry out the feasibility study and prepare the costing for real

industrial projects

4. Produce literature review of the proposed project.

5. Present and defend their project proposal.

6. Produce a project/technical report.

Semester 8, students should be able to

1. Develop a new system or improve an existing product or prototype.

2. Document and rectify the problems, further redefine and prepare

the complete documentation on the system

3. Execute in sequence the various steps required to

produce/manufacture/test/solve/improve the real life industrial

projects/ problems.

4. Analyze the findings and results of the project.

5. Present and defend their project.

6. Produce a final project/technical report.

Synopsis

In this module students are required to work on a project independently orin a group. The project scope ranges from the identification of industrialneeds to final product, comprising of research & development, designcreativity, teamwork, analysis, prototyping, testing, manufacturing,modification and commissioning. Each student will be assessedindependently. At the end of semester 7, students are given an incompletegrade; full grade will only be given at the end of semester 8.

UNIVERSITI KUALA LUMPUR

Semester 7

Contents

Title

1.0 Introduction1.0 Brief introductory to the title1.1 Purpose and objective of study1.2 The problem stated in general

and the specific way1.3 Rationale for problem solving

and methods available1.4 Limitation of project

2.0 Literature Review2.1 Show thorough knowledge of

the research, theory, concepts,ideology and opinion related tothe title

2.2 Make aware that the review isselective

2.3 Show critical analysis of thereview

2.4 Does the review reveal therelation between what haspreviously been done by othersand what is proposed in thisproject

3.0 Research Method3.1 Explain what was done to

gather the information essentialto problem solving such as userrequirements

3.2 Specific research method used todesign the prototype/ product

3.3 Explain if any control methodsand testing are used

3.4 List all the resources needed andtheir usefulness

3.5 Prepare a budget/ costing

4.0 Seminar 1 and Interim Report4.1 Seminar 14.2 Preparation of Interim Report

HoursEquivalent Credit Hours

HoursL0

00

T0

00

p72

722

Rby

UNIVERSITI KUALA LUMPUR

Semester 8

Contents

Title

5.0 Prototype/Product Development5.1 Describe each stage of prototype

development in detail5.2 Detailed technical materials

(such as coding or scripting,diagrams, flow charts,storyboards and etc.)

5.3 Report unforeseen outcome orlimitation, and how these factorswere eliminated or minimized

6.0 Testing and Results6.1 Explain the testing

method/ approach used to testthe prototype

6.2 Describe the complete prototypeand compare with the initialpurpose and objectives

6.3 Discuss the behavior of thefinished prototype and show itsfunctionality and output

6.4 Highlight the results and doinclude any major variationsfrom the original design

7.0 Conclusion and Suggestion7.1 Explain what has been

accomplished and what are themajor things learned form thisproject

7.2 Describe work still needs to bedone on the prototype and howit can be improved and/ orenhanced to become a completeproduct

7.3 Give details on how this productcan be beneficial for futuredevelopment and research

HoursL T P

144

UNIVERSITI KUALA LUMPUR

Main References

References

8.0 Seminar 2 and Report8.1 Seminar 28.2 Preparation of Final Report

HoursEquivalent Credit HoursTotal HoursTotal Equivalent Credit Hours

00

00

1444

2166

1. UniKL Final Year Project (FYP) Manual For Degree Programmes, 1st ed. 2006

Legend:L - Lecture P - Practical T - Tutorial

>i^