UM VIPRO VP7710 v1

VIPRO VP7710

USER’S MANUAL

Version 1.09

April 2, 2018

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

Copyright Copyright © 2013 VIA Technologies Incorporated. All rights reserved.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated

into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise without the prior written permission of VIA Technologies, Incorporated.

Trademarks All trademarks are the property of their respective holders.

Disclaimer No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA

Technologies makes no warranties, implied or otherwise, in regard to this document and to the products

described in this document. The information provided in this document is believed to be accurate and reliable as

of the publication date of this document. However, VIA Technologies assumes no responsibility for the use or

misuse of the information (including use or connection of extra device/equipment/add-on card) in this document

and for any patent infringements that may arise from the use of this document. The information and product

specifications within this document are subject to change at any time, without notice and without obligation to

notify any person of such change.

VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time

without prior notice.

Regulatory Compliance FCC-A Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference, in which case the user will be required to correct the interference at his personal expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

Notice 3

The product described in this document is designed for general use, VIA Technologies assumes no responsibility

for the conflicts or damages arising from incompatibility of the product. Check compatibility issue with your

local sales representatives before placing an order.

SAFETY INSTRUCTIONS � Lay this equipment on a reliable flat surface before setting it up.

� Always unplug the power cord before inserting any add-on card or module.

� Make sure the voltage of the power source and adjust properly 110/220V

before connecting the equipment to the power inlet.

� Place the power cord in such a way that people cannot step on it. Do not

place anything over the power cord.

� Wear a grounded wrist strap when installing components.

� Hold components by the edges to prevent damage to the components.

� Do not flex or stress the components.

� Use the correct screws with the correct threading. Do not over tighten

screws.

� If any of the following situations arises, get the equipment checked by a

service personnel:

� The power cord or plug is damaged.

� Liquid has penetrated into the equipment.

� The equipment has been exposed to moisture.

� The equipment has not worked well or you cannot get it work

according to User's Manual.

� The equipment has dropped and damaged.

� If the equipment has obvious sign of breakage.

� The openings on the enclosure are for air convection hence protects the

equipment from overheating. Do not cover the openings.

� Never pour any liquid into the opening. Liquid can cause damage or

electrical shock.

� Keep this equipment away from humidity.

� Do not leave this equipment in an environment unconditioned or in a

storage temperature above 60oC (140

oF). The equipment may be damaged.

� Keep the original packaging and anti-static bag in case the unit has to be

returned.

� Do not attempt to power-on the system if there is damage to any of its

components.

Caution:

Only use the appropriate battery specified for this product.

Do not reuse, recharge, or reheat an old battery.

Do not attempt to force open the battery.

Do not discard used batteries with regular trash.

Discard used batteries according to local regulations.

PACKAGE CHECK LIST � VIPRO VP7710 system unit x 1

� SATA data cable x 1

� IDE data cable x 1

� Power Cable, DIN-jack to DC-plug x 1

� Panel mounting plate

TABLE OF CONTENTS

VIPRO VP7710 Overview ................................................................................................ 1 Specifications ................................................................................................................. 2

Processor System .................................................................................................... 2 Graphics ...................................................................................................................... 3 LCD Display ............................................................................................................... 3 Touch Screen ............................................................................................................ 3 Ethernet ....................................................................................................................... 4 Audio ............................................................................................................................ 4 Serial ............................................................................................................................. 4 Storage ........................................................................................................................ 4 System Indicator...................................................................................................... 5 Watchdog Timer...................................................................................................... 5 System I/O ................................................................................................................. 5 Power Supply ............................................................................................................ 6 Environmental Specification ............................................................................... 7 Mechanical ................................................................................................................. 8

Layout ............................................................................................................................... 9

Installation .......................................................................................................................... 11 Removing the back plate ....................................................................................... 11 Installing Memory ..................................................................................................... 12 Installing the Hard Drive ........................................................................................ 14 Installing the CF Memory ...................................................................................... 16 Installing the WLAN Module (optional) ........................................................... 18

Mounting Options .......................................................................................................... 21 VESA Mounting Holes ............................................................................................. 21 Desktop Stand (optional) ....................................................................................... 22 Panel Mounting Kit................................................................................................... 23 Wall Mounting Kit (optional)................................................................................ 26

VIPRO VP7710 BIOS SETUP ......................................................................................... 27 Main Menu ................................................................................................................... 27 Standard CMOS Features ...................................................................................... 29 IDE Drives ..................................................................................................................... 30 Advanced BIOS Features ........................................................................................ 31 CPU Feature ................................................................................................................. 34 Hard Disk Boot Priority ........................................................................................... 35 Advanced Chipset Features .................................................................................. 36 AGP & P2P Bridge Control .................................................................................... 37 CPU & PCI Bus Control ........................................................................................... 39 TV Output Connector .............................................................................................. 40

Integrated Peripherals ............................................................................................. 41 VIA OnChip PCI Device ........................................................................................... 42 USB Device Setting ................................................................................................... 43 Power Management Setup ................................................................................... 45 Wakeup Event Detect .............................................................................................. 48 PnP/PCI Configurations .......................................................................................... 50 IRQ Resources ............................................................................................................ 52 PC Health Status ........................................................................................................ 53 Frequency / Voltage Control ................................................................................ 54 DRAM Clock/Drive Control ................................................................................... 55 Load Optimized Defaults ....................................................................................... 58 Set Supervisor / User Password .......................................................................... 59 Save & Exit Setup ...................................................................................................... 60 Exit Without Saving .................................................................................................. 61

Appendix A ........................................................................................................................ 62 Introduction of VIPRO VP7710 External I/O Connectors ......................... 63 VIPRO VP7710 Bottom System External I/O Connectors ......................... 64

Power Input Connector ..................................................................................... 64 Power ON/OFF Switch Button ........................................................................ 64 Audio Connector .................................................................................................. 65 5V/12V switch for COM 2 and COM4 ......................................................... 65 RS-422/485 switch for COM1 ......................................................................... 65 LED indicators ........................................................................................................ 65 COM2 and COM4 Connector ......................................................................... 66 COM1 Connector ................................................................................................. 67 VGA Connector ..................................................................................................... 68

VIPRO VP7710 Side System External I/O connectors ................................ 69 PS/2 Keyboard and PS/2 Mouse Connector............................................. 69 USB Connectors .................................................................................................... 70 Ethernet Connector (LAN) ................................................................................ 71

VIPRO VP7710 User’s Manual

1

VIPRO VP7710 Overview The VIPRO VP7710 Fanless Panel PC is an embedded panel computer

with a 10.4” TFT LCD and resistive touch screen. The VIPRO VP7710 has

a NanoBGA2 central processor (VIA Eden ULV 1.6 GHz or C7 1.0 GHz) —

making it an ideal solution for applications that require low power

consumption, fanless and noise-free operation, and multiple IO ports.

It accepts a wide range of DC power input voltages (from DC 7V – 30V).

The VIPRO VP7710 Panel PC is equipped with one DDR2 533 MHz

SODIMM socket that supports up to 1 GB of memory, three COM ports

(one RS-422/485 and two RS-232 with a 5V/12V selector), one Gigabit

LAN, and two USB 2.0 ports.

The VIPRO VP7710 has an external VGA port that enables dual

independent displays and high definition audio ports that makes it good

for multimedia applications. Storage can be integrated into its internal

Compact Flash socket and 2.5" internal HDD drive bay. It also includes a

variety of mounting options that make it a flexible system to install.

These features make the VIPRO VP7710 Fanless Panel PC suitable for a

wide variety of embedded, multimedia, and industrial HMI (Human

Machine Interface) applications including factory automation systems,

precision machinery, production process control, terminal information

systems, entertainment management systems, and car park automation

systems…etc. The VIPRO VP7710 is a reliable, cost-effective solution that

can shorten your application development time.


2

Specifications

Processor System Processor

• VIA Eden ULV 1.6 GHz (for VP-7710-R1E16A1)

o 800 MHz FSB

o 128 KB L2 cache

o NanoBGA2 package

• VIA C7®

1.0 GHz (for VP-7710-R1C10A1)

o 400 MHz FSB

o 128 KB L2 cache

o NanoBGA2 package

Chipset

• VIA CX700M Unified Digital IGP chipset

BIOS

• Award 4-Mbit Flash BIOS

System Power Management

• Timer Power On

• ACPI Support

System Memory

• 1 x 200-pin DDR2 533 SDRAM SODIMM socket

• Supports up to 1 GB of DDR2 SDRAM


3

Graphics Controller

• Integrated VIA C-Pro II 3D/2D AGP graphics with MPEG-2 and

WMV9 video decoding acceleration

Display Memory

• Optimized Shared Memory Architecture, supports up to 128

MB frame buffer using system memory

LCD Display LCD Type

• 10.4” Color TFT LCD panel

Resolution/Color

• Up to 800 X 600 @ 262K

Pixel pitch (mm)

• 0.264 x 0.264

Viewing angle

• 70° (right), 70° (left), 50° (up) and 60° (down)

Luminance

• 230 cd/m2

Backlight MTBF

• 30,000 hours (typical)

Touch Screen Type

• Analog Resistive, continuous resolution

(up to 1 million touches)

Light Transmission

• 82.5% (Typical)

Controller

• USB interface


4

Ethernet Controller

• VIA VT6122 Gigabit Ethernet

Interface

• Supports one RJ45 connector

• Supports Wake On LAN (WOL)

• Supports Pre-boot Execution Environment (PXE)

Audio Controller

• VIA VT1708A High Definition Audio Codec

Interface

• Supports Line-in, Speaker-out, and Mic-in connectors

Serial USB

• 2 x USB ports, USB 2.0 compliant

Serial Ports

• 3 x COM ports consisting of 2 x RS-232 and 1 x RS-422/485

• 5V/12V selectable

Storage HDD

• 1 x 2.5 inch drive bay

Compact Flash

• 1 x Type I socket


5

System Indicator Power Status LED

• 1 x orange color LED

HDD Activity LED

• 1 x blue color LED

Watchdog Timer Output

• System reset

Interval

• Programmable 1~255 seconds

System I/O Bottom I/O ports

• 1 x VGA connector

• 1 x RS-422/485 serial port (COM1)

• 2 x RS-232 serial ports (COM2 and COM4)

• 1 x 5V/12V selectable switch for COM2 and COM4

• 3 x Audio jacks consisting of Line-out, Line-in, and Mic-in

• 1 x ATX power button

• 1 x 2-pole, DC DIN jack power input connector

• 1 x antenna hole for the optional WLAN

Side I/O ports

• 1 x PS/2 mouse connector

• 1 x PS/2 keyboard connector

• 2 x USB 2.0 connectors

• 1 x RJ45 connector

Note:

Refer to Appendix A for the pin assignments of the system I/O ports.


6

Power Supply Sub-Model VP7710-R1E16A1 VP7710-R1C10A1

Power Consumption Maximum 32w

Typical 24.6W

Maximum 28w

Typical 22.8W

Input Voltage

7VDC ~ 30VDC

Typical

7VDC @ 4.57A

12VDC @ 2.66A

16VDC @ 1.93A

19VDC @ 1.68A

24VDC @ 1.33A

30VDC @ 1.1A

7VDC ~ 30VDC

Typical

7VDC @ 3.25A

12VDC @ 1.9A

16VDC @ 1.42A

19VDC @ 1.2A

24VDC @ 0.95A

30VDC @ 0.76A

Input Power Protection

Support Over Voltage protection

Support Over Current Protection

Support Under Voltage Protection


7

Environmental Specification Operating Temperature

• 0°C ~ 45 °C

Storage Temperature

• -20°C ~ 70 °C

Relative Humidity

• 0 ~ 90% @ 45°C, non-condensing

Vibration Loading during operation

• When the system is only equipped with a Compact Flash Disk:

5 Grms, IEC 60068-2-64, random, 5 ~ 500 Hz, 1 Oct./min, 1

hr/axis

Shock during operation

• When system equipped with 2.5-inch Hard Disk Drive:

20 G, IEC 60068-2-27, half size, 11 ms duration

• When system equipped with Compact Flash Disk:

50 G, IEC 60068-2-27, half size, 11 ms duration

Front Panel Protection

• IP 65 compliant

EMC Approved

• CE/FCC Class B

Safety Approved

• UL/CB


8

Mechanical Construction

• Aluminum mixed with heavy-duty steel

Mounting

• Panel/Wall/Table/VESA mountable

Weight

• 3.6 kg (7.9 lbs)

Dimensions (W x H x D)

• 300.4 mm x 205.9 mm x 55.2 mm (11.82” x 8.1” x 2.17”)

• VESA MIS-D 100 mounting interface (100 mm x 100 mm)

Note:

Specifications are subject to change without prior notice.

Unit: mm


9

Layout


10


11

Installation

Removing the back plate

Remove the screws and lift off the back plate.


12

Installing Memory

Step 1

Locate the memory slot.


13

Step 2

Align the notch on the SODIMM with the memory slot.

Step 3

Insert the SODIMM at a 45 degree angle. Then push the SODIMM down

until it snaps into the locking mechanism.

Note:

Due to certain hardware limitations, DDR2 SDRAM modules

organized as 8 banks of 128 MB are not supported.


14

Installing the Hard Drive

Step 1

Remove the four flat screws and the hard drive mounting plate.

Step 2

Attach the 2.5 inch hard disk to the hard drive mounting plate.


15

Step 3

Align the hard drive mounting plate over the guard plate and fasten the

four flat screws to secure the hard drive.

Step 4

Attach one end of the hard disk data cable to the hard disk. Attach the

other end to the hard disk connector on the mainboard. The VIPRO

VP7710 supports both IDE and SATA hard drives. Depending on the

hard drive, use either the IDE or SATA cable and connect to the

appropriate port.

Note:

Modules in the VIPRO VP7710 Series are very fragile and sensitive.

Should you replace or return any component for repair, consult an

authorized technician to dismantle it.


16

Installing the CF Memory Step 1

Remove the four flat screws and the hard drive mounting plate.

Step 2

Remove the guard plate.

Step 3

Align the CF card with the side rails on the CF slot and insert firmly.

Step 4

Align the guard plate and insert the two flathead screws to the left and

right of the CF card.


17

Step 4

Align the hard drive mounting plate and secure it with the four flat

screws.


18

Installing the WLAN Module (optional)

Step 1

Locate the WLAN mounting holes.


19

Step 2

Align the WLAN module over the mounting hole and secure it with two

screws as shown.

Step 3

Attach the antenna cable to the WLAN module.

Step 4

Attach one end of the USB cable to the IO board and the other end to

the WLAN module.

Caution:

Before closing the VIPRO VP7710, ensure that the FFC cables

connecting the mainboard to the IO board are fully attached.

Otherwise, the VIPRO VP7710 may not function.


20

Step 5

After reattaching the backplate to the VIPRO VP7710, located the WLAN

antenna port. Screw on the WLAN antenna.


21

Mounting Options

VESA Mounting Holes The VIPRO VP7710 has VESA MIS-D 100 mounting holes on the back

plate. The mounting holes are set 10 cm apart (see the figure below).

The VIPRO VP7710 can only be mounted on VESA MIS-D 100

compatible devices.


22

Desktop Stand (optional)

An optional stand is available for enabling the VIPRO VP7710 to be

rested on a flat surface. For details on the assembly of the desktop stand,

refer to the installation guide provided with the desktop stand.


23

Panel Mounting Kit

Panel mounting should be used in situations where only the front and

bezel of the VIPRO VP7710 will be visible. In order to complete a panel

mount, the wall must have a designated space (cutout) for embedding

the VIPRO VP7710.

A recommended cutout dimension is shown below.

Note:

The cutout shown above is for embedding the VIPRO VP7710

directly into the wall without an additional chassis. If using a chassis

to mount the VIPRO VP7710, ensure the cutout is sufficient for the

chassis.

Unit: mm


24

Once the cutout has been prepared, slide the VIPRO VP7710 backwards

into the panel opening. From the other side of the panel, align the panel

mounting bracket on the rear of VIPRO VP7710 and attach the eight

screws through the mounting bracket into the backplate.


25

Then, secure the VIPRO VP7710 to the panel with four screws.


26

Wall Mounting Kit (optional)

Wall mounting should be used when the VIPRO VP7710 cannot be

embedded into the wall. When wall mounting, the entire system will be

exposed. For details on the assembly of the wall mounting kit, refer to

the installation guide provided with the wall mounting kit.


27

VIPRO VP7710 BIOS SETUP

Main Menu

Standard CMOS Features

Use this menu to set basic system configurations.

Advanced BIOS Features

Use this menu to set the advanced features available on your system.

Advanced Chipset Features

Use this menu to set chipset specific features and optimize system

performance.

Integrated Peripherals

Use this menu to set onboard peripherals features.

Power Management Setup

Use this menu to set onboard power management functions.

PnP/PCI Configurations

Use this menu to set the PnP and PCI configurations.


28

PC Health Status

This menu shows the PC health status.

Frequency/Voltage Control

Use this menu to set the system frequency and voltage control.

BIOS Setup

Load Optimized Defaults

Use this menu option to load BIOS default settings for optimal and high

performance system operations.

Set Supervisor Password

Use this menu option to set the BIOS supervisor password.

Set User Password

Use this menu option to set the BIOS user password.

Save & Exit Setup

Save BIOS setting changes and exit setup.

Exit Without Saving

Discard all BIOS setting changes and exit setup.


29

Standard CMOS Features

Date

The date format is [Day, Month Date Year]

Time

The time format is [Hour : Minute : Second]

Video

Settings: [EGA/VGA, CGA 40, CGA 80, Mono]

Halt On

Sets the system’s response to specific boot errors. Below is a table that

details the possible settings. Setting Description

All Errors System halts when any error is detected

No Errors System does not halt for any error

All, But Keyboard System halts for all non-key errors


30

IDE Drives

The specifications of your drive must match with the drive table. The

hard disk will not work properly if you enter incorrect information in this

category.

Select “Auto” whenever possible. If you select “Manual”, make sure the

information is from your hard disk vendor or system manufacturer.

Below is a table that details required hard drive information when using

the “Manual” mode.

Setting Description

IDE Channel The name of this match the name of the menu.

Settings: [None, Auto, Manual]

Access Mode Settings: [CHS, LBA, Large, Auto]

Capacity Formatted size of the storage device

Cylinder Number of cylinders

Head Number of heads

Precomp Write precompensation

Landing Zone location of the landing zone

Sector Number of sectors


31

Advanced BIOS Features

Virus Warning

This item is used to enable or disable the VIRUS warning feature for IDE

Hard Disk boot sector protection. Setting Description

Enabled Turns on hard disk boot sector virus protection

Disabled Turns off hard disk boot sector virus protection

Quick Power On Self-Test

Shortens Power On Self-Test (POST) cycle to enable shorter boot up

time. Setting Description

Enabled Shorten Power On Self Test (POST) cycle and bootup

time

Disabled Standard Power On Self Test (POST)


32

First/Second/Third Boot Device

Set the boot device sequence as BIOS attempts to load the disk

operating system. Setting Description

LS120 Boot from LS-120 drive

Hard Disk Boot from the HDD

CD-ROM Boot from CD-ROM

ZIP100 Boot from ATAPI ZIP drive

USB-FDD Boot from USB floppy drive

USB-ZIP Boot from USB ZIP drive

USB-CDROM Boot from USB CDROM

Legacy LAN Boot from network drive

VIA Networking Boot from network drive

Disabled Disable the boot device sequence

Boot Other Device

Enables the system to boot from alternate devices if the system fails to

boot from the “First/Second/Third Boot Device” list. Setting Description

Enabled Enable alternate boot device

Disabled No alternate boot device allowed

Boot Up NumLock Status

Set the NumLock status when the system is powered on. Setting Description

On Forces keypad to behave as 10-key

Off Forces keypad to behave as arrow keys

Typematic Rate Setting

Enables “Typematic Rate” and “Typematic Delay” functions.

Settings: [Enabled, Disabled]

Typematic Rate (Chars/Sec)

This item sets the rate (characters/second) at which the system retrieves

a signal from a depressed key.

Settings: [6, 8, 10, 12, 15, 20, 24, 30]

Typematic Delay (Msec)

This item sets the delay between when the key was first pressed and

when the system begins to repeat the signal from the depressed key.

Settings: [250, 500, 750, 1000]


33

Security Option

Selects whether the password is required every time the System boots,

or only when you enter Setup. Setting Description

Setup Password prompt appears only when end users try to

run BIOS Setup

System Password prompt appears every time when the

computer is powered on and when end users try to

run BIOS Setup

APIC Mode

Settings: [Disabled, Enabled]

MPS Version Control for OS

Settings: [1.1, 1.4]

OS Select For DRAM > 64MB

Select OS2 only if you are running OS/2 operating system with greater

than 64MB of RAM on the system.

Settings: [Non-OS2, OS2]

Video BIOS Shadow

Enabled copies Video BIOS to shadow RAM Improves performance.


Full Screen Logo Show


Small Logo(EPA) Show


Summary Screen Show



34

CPU Feature

Deplay Prior to Thermal

Settings: [4 Min, 8 Min, 16 Min, 32 Min]

Thermal Management

This item sets CPU’s thermal control rule to protect CPU from overheat. Setting Description

Thermal Monitor

1

On-die throttling

TM2 Bus Ratio

This item sets the frequency (bus ratio) of the throttled performance

that will be initiated when the on die sensor goes from not hot to hot.

TM2 Bus VID

This item sets the voltage of the throttled performance that will be

initiated when the on die sensor goes from not hot to hot.

C7 CMPXCHGB


C7 NoExecute (NX)



35

Hard Disk Boot Priority

This is for setting the priority of the hard disk boot order when the

“Hard Disk” option is selected in the “[First/Second/Third] Boot Device”

menu item.


36

Advanced Chipset Features

Caution:

The Advanced Chipset Features menu is used for optimizing the

chipset functions. Do not change these settings unless you are

familiar with the chipset.

Memory Hole

Settings: [Disabled, 15M – 16M]

System BIOS Cacheable


Video RAM Cacheable


Init Display First

Settings: [PCI Slot, AGP]

Display Device Output 1 / 2

Select from a variety of supported display devices.

Settings: [Disabled, CRT, LCD, TV, DVI, CRT2]

Panel Type

Key in a HEX number.

Settings: [Min = 0000, Max = 00FF]


37

AGP & P2P Bridge Control

AGP Aperture Size

This setting controls how much memory space can be allocated to AGP

for video purposes. The aperture is a portion of the PCI memory address

range dedicated to graphics memory address space. Host cycles that hit

the aperture range are forwarded to the AGP without any translation.

Settings: [32MB, 64MB, 128MB, 256MB, 512MB, 1G]

AGP 3.0 Mode

This mainboard supports the AGP 4x interface. When the AGP 4x is used,

it can transfer video data at 1066MB/s. AGP 4x is backward compatible,

leave the default 4x mode on.

Settings: [8x, 4x]

AGP Driving Control

This item is used to signal driving current on AGP cards to auto or

manual.

Settings: [Auto, Manual]

AGP Driving Value




38

AGP Fast Write

This item is used to enable or disable the caching of display data for the

video memory of the processor.


AGP Master 1 WS Write


AGP Master 1 WS Read


AGP 3.0 Calibration Cycle


VGA Share Memory Size

Settings: [Disabled, 32M, 64M, 128M]

Direct Frame Buffer



39

CPU & PCI Bus Control

PCI Master 0 WS Write


PCI Delay Transaction


DRDY_Timing

Settings: [Slowest, Default, Optimize]


40

TV Output Connector

The TV Output Connector sub-menu gives access to enable or disable

the output connector types listed onscreen.


41

Integrated Peripherals

RS422/485 and Onboard Serial Port

Sets the base I/O port address and IRQ for the onboard serial ports.

Selecting “Auto” allows the BIOS to automatically determine the correct

base I/O port address. Port Settings

RS422/485 Disabled 3F8

IRQ4

2F8

IRQ4

3E8

IRQ4

2E8

IRQ4

Auto

1 Disabled 3F8

IRQ4

2F8

IRQ4

3E8

IRQ4

2E8

IRQ4

Auto

2 Disabled 3F8

IRQ4

2F8

IRQ4

3E8

IRQ4

2E8

IRQ4

Auto

WatchDog Support


WatchDog Timer Select

This item can only be accessed if WatchDog Support is enabled.

Settings: [Second, Minute]

WatchDog Count Value

This item can only be accessed if WatchDog Support is enabled.




42

VIA OnChip PCI Device

Azalia HDA Controller Setting Description

Auto Enables onboard controller if audio device is

detected

Disabled Turn off onboard controller to allow external

controller

OnBoard LAN Boot ROM



43

USB Device Setting

USB 1.0 Controller

Enable or disable Universal Host Controller Interface for Universal Serial

Bus.


USB 2.0 Controller

Enable or disable Enhanced Host Controller Interface for Universal Serial

Bus.


USB Operation Mode

Auto decide USB device operation mode. Setting Description

High Speed If USB device was high speed device, then it operated on

high speed mode. If USB device was full/low speed

device, then it operated on full/low speed mode.

Full/Low Speed All of USB Device operated on full/low speed mode


44

USB Keyboard Function

Enable or disable Legacy support of USB Keyboard


USB Storage Function

Enable or disable Legacy support of USB Mass Storage



45

Power Management Setup

Note:

ACPI is a power management specification that makes hardware

status information available to the operating system. ACPI enables a

PC to turn its peripherals on and off for improved power

management. It also allows the PC to be turned on and off by

external devices, so that mouse or keyboard activity wakes up the

computer.

ACPI Suspend Type Setting Description

S1(POS) S1/Power On Suspend (POS) is a low power state. In

this state, no system context (CPU or chipset) is lost

and hardware maintains all system contexts.

S3(STR) S3/Suspend To RAM (STR) is a power-down state. In

this state, power is supplied only to essential

components such as main memory and wakeup-

capable devices. The system context is saved to main

memory, and context is restored from the memory

when a "wakeup" event occurs.

S1 & S3 Depends on the OS to select S1 or S3.


46

Power Management Option

Settings: [User Defined, Min Saving, Max Saving]

HDD Power Down

Sets the length of time for a period of inactivity before powering down

the hard disk.

Settings: [Disabled, 1~15(minutes)]

Suspend Mode

Sets the length of time for a period of inactivity before entering suspend

mode.

Settings: [Disabled, 1~15(minutes)]

Video Off Option

Select whether or not to turn off the screen when system enters power

saving mode, ACPI OS such as Windows XP will override this option. Setting Description

Always On Screen is always on even when system enters power

saving mode

Suspend -> Off Screen is turned off when system enters power

saving mode

Video Off Method

Settings: [Blank Screen, V/H Sync+Blank, DPMS Support]

Modem Use IRQ

Settings: [NA, 3, 4, 5, 7, 9, 11]

Soft-off by PWRBTN

This field configures the power button on the chassis. Setting Description

Delay 4 Sec System is turned off if power button is pressed for

more than four seconds

Instant-Off Power button functions as a normal power-on/-off

button


47

Run VGABIOS if S3 Resume

Settings: [Auto, Yes, No]

AC Loss Auto ReStart

The field defines how the system will respond after an AC power loss

during system operation. Setting Description

Off Keeps the system in an off state until the power

button is pressed

On Restarts the system when the power is back

Former-Sts Former-Sts


48

Wakeup Event Detect

PS2KB Wakeup Select

When selecting “Password”, press <Page Up> or <Page Down> to

change password. The maximum number of characters is eight. “PS2MS

Wakeup from S3/S4/S5” and “PS2KB Wakeup from S3/S4/S5” will be

disabled while changing the password.

Settings: [Hot Key, Password]

PS2KB Wakeup Key Select

Sets a Hot Key to restore the system from the power saving mode to an

active state.

Settings: [Disabled, Ctrl+F1, Ctrl+F2, Ctrl+F3, Ctrl+F4, Ctrl+F5, Ctrl+F6,

Ctrl+F7, Ctrl+F8, Ctrl+F9, Ctrl+F10, Ctrl+F11, Ctrl+F12, Power, Wake, Any

Key]

PS2MS Wakeup Key Select

Enables any mouse activity to restore the system from the power saving

mode to an active state.


PS2 Keyboard Power On


PS2 Mouse Power On



49

USB Resume


PowerOn by PCI Card

Settings: [By OS, Enabled]

Wake Up On LAN/Ring

Enables any LAN or Ring-In signals from the LAN or modem to restore

the system from a suspended state to an active state.

Settings: [By OS, Enabled]

RTC Alarm Resume

Sets a scheduled time and/or date to automatically power on the system.


Date (of Month)

The field specifies the date for “RTC Alarm Resume”.

Resume Time (hh:mm:ss)

The field specifies the time for “RTC Alarm Resume”.


50

PnP/PCI Configurations

Note:

This section covers some very technical items and it is strongly

recommended to leave the default settings as is unless you are an

experienced user.

PNP OS Installed Setting Description

Yes BIOS will only initialize the PnP cards used for

booting (VGA, IDE, SCSI). The rest of the cards will be

initialized by the PnP operating system

No BIOS will initialize all the PnP cards

Reset Configuration Data

This field should usually be left “Disabled”. Setting Description

Enabled Resets the ESCD (Extended System Configuration

Data) after exiting BIOS Setup if a newly installed PCI

card or the system configuration prevents the

operating system from loading

Disabled Default setting


51

Resource Controlled By

Enables the BIOS to automatically configure all the Plug-and-Play

compatible devices. Setting Description

Auto(ESCD) BIOS will automatically assign IRQ, DMA and memory

base address fields

Manual Unlocks “IRQ Resources” for manual configuration

PCI/VGA Palette Snoop

Some non-standard VGA display cards may not show colors properly.

This field allows you to set whether MPEG ISA/VESA VGA Cards can

work with PCI/VGA or not. When enabled, a PCI/VGA can work with a

MPEG ISA/VESA VGA card. When disabled, a PCI/VGA cannot work with

a MPEG ISA/VESA Card.


Assign IRQ For VGA/USB

Assign IRQ for VGA and USB devices.


Maximum ASPM supported

Settings: [L0, L0s, L1, L0s&L1]

Maximum Payload Size

Settings: [128, 256, 512, 1024, 2048, 4096]


52

IRQ Resources

Note:

The items are adjustable only when “Resources Controlled By” is set

to “Manual.”

IRQ Resources list IRQ 3/5/7/9/10/11/14/15 for users to set each IRQ a

type depending on the type of device using the IRQ.

Setting Description

PCI Device For Plug-and-Play compatible devices designed for

PCI bus architecture

Reserved The IRQ will be reserved for other requests


53

PC Health Status

This screen displays real-time values for the voltages listed. In addition,

it shows the fan speed of any fan attached to the onboard fan connector.


54

Frequency / Voltage Control

Auto Detect PCI Clk


Spread Spectrum

When the mainboard's clock generator pulses, the extreme values

(spikes) of the pulses creates EMI (Electromagnetic Interference). The

Spread Spectrum function reduces the EMI generated by modulating

the pulses so that the spikes of the pulses are reduced to flatter curves.

Settings: [Disabled, 0.20%, 0.25%, 0.35%]


55

DRAM Clock/Drive Control

DRAM Clock

The chipset supports synchronous and asynchronous mode between

host clock and DRAM clock frequency.

Settings: [200MHz, 266MHz, 333MHz, By SPD]

DRAM Timing

The value in this field depends on the memory modules installed in your

system. Changing the value from the factory setting is not

recommended unless you install new memory that has a different

performance rating than the original modules.

Settings: [Manual, Auto By SPD]

SDRAM CAS Latency [DDR/DDR2]

This item is for setting the speed it takes for the memory module to

complete a command. Generally, a lower setting will improve the

performance of your system. However, if your system becomes less

stable, you should change it to a higher setting. This field is only

available when “DRAM Timing” is set to “Manual”.

Settings: [1.5/2, 2/3, 2.5/4, 3/5]


56

Bank Interleave

This item is for setting the interleave mode of the SDRAM interface.

Interleaving allows banks of SDRAM to alternate their refresh and access

cycles. One bank will undergo its refresh cycle while another is being

accessed. This improves performance of the SDRAM by masking the

refresh time of each bank. This field is only available when “DRAM

Timing” is set to “Manual”.

Settings: [Disabled, 2 Bank, 4 Bank, 8 Bank]

Precharge to Active (Trp)

This field is for setting the length of time it takes to precharge a row in

the memory module before the row becomes active. Longer values are

safer but may not offer the best performance. This field is only available

when “DRAM Timing” is set to “Manual”.

Settings: [2T, 3T, 4T, 5T]

Active to Precharge (Tras)

This field is for setting the length of time it a row stays active before

precharging. Longer values are safer but may not offer the best

performance.

This field is only available when “DRAM Timing” is set to “Manual”.

Settings: [05~20T]

Active to CMD (Trcd)



REF to ACT / REF (Trfc)


Settings: [08~71T]

ACT(0) to ACT(1) (TRRD)



Read to Precharge (Trptp)

Settings: [2T, 3T]

Write to Read CMD (Twtr)

Settings: [1T/2T, 2T/3T]


57

Write Recovery Time (Twr)


RDSAIT Mode

Settings: [Manual, Auto]

RDSAIT Selection


Settings: [Min = 0000, Max = 003F]


58

Load Optimized Defaults

This option is for restoring all the default optimized BIOS settings. The

default optimized values are set by the mainboard manufacturer to

provide a stable system with optimized performance.

Entering “Y” loads the default optimized BIOS values.


59

Set Supervisor / User Password

This option is for setting a password for entering BIOS Setup. When a

password has been set, a password prompt will be displayed whenever

BIOS Setup is run. This prevents an unauthorized person from changing

any part of your system configuration.

There are two types of passwords you can set. A supervisor password

and a user password. When a supervisor password is used, the BIOS

Setup program can be accessed and the BIOS settings can be changed.

When a user password is used, the BIOS Setup program can be accessed

but the BIOS settings cannot be changed.

To set the password, type the password (up to eight characters in length)

and press <Enter>. The password typed now will clear any previously set

password from CMOS memory. The new password will need to be

reentered to be confirmed. To cancel the process press <Esc>.

To disable the password, press <Enter> when prompted to enter a new

password. A message will show up to confirm disabling the password.

To cancel the process press <Esc>.

Additionally, when a password is enabled, the BIOS can be set to

request the password each time the system is booted. This would

prevent unauthorized use of the system. See “Security Option” in the

“Advanced BIOS Features” section for more details.


60

Save & Exit Setup

Entering “Y” saves any changes made and exits the program.

Entering “N” will cancel the exit request.


61

Exit Without Saving

Entering “Y” discards any changes made and exits the program.

Entering “N” will cancel the exit request


62

Appendix A

The pin assignments of the external system I/O ports on the bottom and

side of the system are described here.


63

Introduction of VIPRO VP7710 External I/O

Connectors

The following two figures show the external I/O connectors on VIPRO

VP7710. The following sections give you detailed information about the

function of each I/O connector.

Figure A.1: Bottom System I/O connectors

Figure A.2: Side System I/O connectors


64

VIPRO VP7710 Bottom System External I/O

Connectors

Power Input Connector The VIPRO VP7710 comes with a 2-pole DIN-jack that carries external

power input of 7~30 VDC. Please refer to Figure A.3 and Table A.2.1 for

their pin assignments.

Figure A.3: 2-pole, DC DIN-Jack of Power Input connector

Table A.1: Power connector pin assignments

Pin Signal Name

1 +7 ~ 30VDC input voltage

2 GND

Power ON/OFF Switch Button The VIPRO VP7710 comes with a Power On/Off button, that Support

dual function of Soft Power -On/Off (Instant off or Delay 4 Second), and

Suspend.

Pin 1

Pin 2


65

Audio Connector The VIPRO VP7710 offers High Definition Audio output ports by three

phone jack (3.5φ, 5P, 90D(F)) connectors of Mic_In (Pink color), Line_In

(BLUE color), and Line_Out (GREEN color)

Table A.2: Mic_In connector

Mic-In Connector

Footprint Phone Jack 3.5Ø 5P, 90 Degree, Female, PINK color, with SHIELDED

Table A.3: Line_In connector

Line-In Connector

Footprint Phone Jack 3.5Ø 5P, 90 Degree, Female, BLUE color, with SHIELDED

Table A.4: Line_Out connector

Line-Out Connector

Footprint Phone Jack 3.5Ø 5P, 90 Degree, Female, GREEN color, with SHIELDED

5V/12V switch for COM 2 and COM4 The VIPRO VP7710 comes with a switch that can be configured to carry

the power source of either 5V or 12V for COM 2 and COM4.

RS-422/485 switch for COM1 The COM1 port connector can be configured to operate in either RS-422

or RS-485 mode by setting up this RS-422/485 switch.

LED indicators There are two LEDs on bottom system I/O line of the VIPRO VP7710 for

indicating system status: PWR LED is for power status and Flash in

Orange color; and HDD LED is for hard disk and compact flash disk

status, which flash in Blue color.


66

COM2 and COM4 Connector The VIPRO VP7710 provides two RS-232 ports by two D-sub 9-pin

connectors as COM2 and COM4. Please refer to Figure A.4 and Table A.5

for their pin assignments.

1 5

96

32 4

7 8

Figure A.4: COM 2 and COM 4 Connector

Table A.5: COM2 and COM4 standard serial port pin assignments

Pin Signal Name

1 DCD

2 RxD

3 TxD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI


67

COM1 Connector The VIPRO VP7710 provides a RS-422/485 port, which can be configured

to operate in either RS-422 or RS-485 mode by setting up this RS-

422/485 switch. Please refer to Figure A.5 and Table A.6 for their pin

assignments.

1 5

96

32 4

7 8

Figure A.5: COM1 Connector

Table A.6: COM1 standard serial port pin assignments

Pin RS-422 Signal Name RS-485 Signal Name

1 Tx- Tx-

2 Tx+ Tx+

3 Rx+ NC

4 Rx- NC

5 GND GND

6 NC NC

7 NC NC

8 NC NC

9 NC NC

Note:

NC represents “No Connection”.


68

VGA Connector The VIPRO VP7710 provides a high resolution VGA interface by a D-sub

15-pin connector to support the connection with a VGA CRT monitor

externally. Please refer to Figure A.6 and Table 2.7 for their pin

assignments.

5

15

1

11

10 6

Figure A.6: VGA connector

Table A.7: VGA port pin assignments

Pin Signal Name Pin Signal Name

1 RED 9 NC

2 GREEN 10 GND

3 BLUE 11 NC

4 NC 12 DDC DATA

5 GND 13 H-SYNC

6 GND 14 V-SYNC

7 GND 15 DDC CLOCK

8 GND


69

VIPRO VP7710 Side System External I/O

connectors

PS/2 Keyboard and PS/2 Mouse Connector The VIPRO VP7710 provides a PS/2 keyboard connector and a PS/2

mouse connector. Two 6-pin mini-DIN connectors are located on the

right side of the VIPRO VP7710. Please refer to Figure A.7 and Table A.8

for its pin assignments.

5

3

12

4

6

Figure A.7: PS/2 Mouse and PS/2 Keyboard connector

Table A.8: PS2 Connectors

Pin Keyboard Signals Pin Mouse Signals

1 KB DATA 9 MS DATA

2 NC 10 NC

3 GND 11 GND

4 +5V 12 +5V

5 KB CLOCK 13 MS CLOCK

NC NC


70

USB Connectors The VIPRO VP7710 provides two USB-interface connectors located on

right side of it. These USB-interface connectors give complete Plug &

Play and hot swapping for up to 127 external devices. The USB interface

can be disabled in the system BIOS setup. Please refer to Figure A.8 and

Table A.9 for its pin assignments.

The USB-interface connector is used for connecting any device that

conforms to the USB interface. Many recent digital devices conform to

this standard. The USB interface supports Plug and Play, which enables

you to connect or disconnect a device whenever you want, without

turning off the computer.

Figure A.8: USB connector

Table A.9 USB Connector

Pin Signal Name

1 VCC

2 USB_P0-

3 USB_P0+

4 GND


71

Ethernet Connector (LAN) The VIPRO VP7710 is equipped with a VIA VT6122 Gigabit Ethernet

controller that is fully compliant with IEEE 802.3 (10BASE-T), 802.3u

(100BASE-TX), and 802.3ab (1000BASE-T) standards.

1 81 8

Figure 2.6: RJ-45 Connector

Table A.10: RJ-45 Connector pin assignments

Pin Signal Name

1 Tx+

2 Tx-

3 Rx+

4 Rx-

5 TxA+

6 TxA-

7 RxA+

8 RxA-

The Ethernet port provides a standard RJ-45 jack connector with LED

indicators on the front side to show its Active/Link status, please find the

details from table A.11 below.

Table A.11: LAN LED status indicators

Speed Active Link

10 Base-T Orange Blink N/A

100 Base-T Orange Blink Red

1000 Base-T Orange Blink Green

Documents

UM VIPRO VP7710 v1