Ultra Flat Wall Mount Computer Station (UFWM Series) Assembly Instructions

Packed By:

__________________________

Checked By:

__________________________

Assembly Instructions Ultra Flat Wall Mount Computer StationVersaTables.com

VersaTables.com 14105 Avalon Blvd. Los Angeles CA 90061 800-416-3961 (310) 353-7100 Fax (310) 353-7109

Proudly Made in the USA. Revised: 7/24/08

FRAME :BLACK RIVER WARM GRAY

BG

How can we improve our assembly instructions? Your comments and suggestions are important to us.

Please email us at: [email protected]

Assembly Instructions Ultra Flat Wall Mount Computer Station


VersaTables.com

Proudly Made in the USA.

QTY: 13

QTY: 2

L Panel

QTY: 1

Back Panel

QTY: 1

LCD Monitor Holder Keyboard Drawer

QTY: 1

Front Panel

QTY: 1

QTY: 6 QTY: 4 QTY: 13

10-32 Carriage Bolt 50mm Furniture Bolt8mm Machine Screw 2” Phillips Head Lag Bolt

QTY: 13

Toggler

Wall L Panel

QTY: 2

QTY: 1

Cable Grommet Adjustment Knob

QTY: 6

1/4 “ WasherQTY: 6

1/4” 20 mm Furniture Bolt QTY: 9



VersaTables.com


Step 1

Step 2 Step 3

Drill 1/2" (Ø13mm) hole. Hold metal channel flat alongside plastic straps and

slide channel through hole. Minimum clearance behind wall: 1 7/8" (48mm).

Remove the 1/4” Bolts and take apart the Front and Back Panels

Use Back Panel to premark the places where holes will be drilled to use toggler and bolts to

secure it to the wall.

1/4” 20 mm Furniture Bolt



VersaTables.com


Step 4 Step 5

Step 6 Step 7

Hold ends of straps between thumb and forefinger and pull toward you until channel rests flush behind wall. Slide plastic cap along straps with

other hand until flange of cap is flush with wall.

Snap straps at wall by pushing side to side, snapping off straps

level with flange of cap.

Place Back Panel over flange. Insert 50mm Furniture Bolt through item

and tighten until flush against item, then stop.

Use machine screw or bolt to match threadin channel: BA (3/16"-24), BB (1/4"-20), BM5 (M5),

or BM6 (M6).Bolt length = item thickness + wall or ceiling thickness + 1/2" (13mm)

Use 50 mm Furniture Bolts to secure Back Panel to the wall.

50 mm Furniture Bolt



VersaTables.com


Step 8

Step 9

Remove Bracket from the Wall Mount sliding it up and forward to

attach the LCD Monitor to it.

Attach LCD Monitor using (4) 8mm machine screw.

8mm Machine Screw

Step 10



VersaTables.com


Secure LCD Holder Bracket back to the Wall Mount

Make sure tabs have gone through the holes , then tIghted bolt to secure the

LCD Holder.

Tab

1/4” 20 mm Bolt

Step 11

Step 12

Mount the slide Mechanism

Allign Wall L panels and L Panels and secure them.

Allign Upper and Lower Panel Mechanisms and secure them.



VersaTables.com


Use 10-32 Carriage Bolt,

Rivets and Knobs

Use 10-32 Carriage Bolt,

Rivets and Knobs

10-32 Carriage Bolt

Step 13 Secure CPU Holder to the Wall.



VersaTables.com


Adjust LCD Monitor, Keyboard and CPU Holder as needed.

How can we improve our assembly instructions? Your comments and suggestions are important to us.

Please email us at: [email protected]

50 mm Furniture Bolt

Documents

Ultra Flat Wall Mount Computer Station (UFWM Series) Assembly Instructions