Upload
others
View
23
Download
0
Embed Size (px)
Citation preview
ULTRA-CLEAN CCD CRYOSTATS CCD Contamination can be kept under control
S. Deiries, O. Iwert, C. Cavadore, C. Geimer, and E. Hummel European Southern Observatory, Karl-Schwarzschild-Str. 2, D-85748 Garching, Germany
Abstract: A reproducible methodology is given to achieve ultra-clean CCD cryostats: A list of suitable materials and the necessary treatments are presented. In addition to this, the proper handling under clean-room conditions and suitable molecular sieves eliminate contamination on the detector surface in cold cryostats for years. Key words: contamination, cleaning, CCD, cryostat, charcoal, clean-room, out-gassing, zeolith
1. INTRODUCTION
During the last years, ESO’s Optical Detector Team (ODT) developed a comprehensive methodology to achieve ultra-clean CCD cryostats, because
scientific results are insecure, if obtained with dirty systems. Usually, contamination first decreases the ultra-violet and blue spectral response of a CCD sensor. This phase is still invisible for the naked eye. If contamination features are visible, the resulting effect is much higher and obviously affects also the visible spectral range. In order to measure these QE changes at the telescope, the ODT built a
1 Figure 1: Contaminated CCDs
2 S. Deiries, O. Iwert, C. Cavadore, C. Geimer, and E. Hummel portable test bench. A reliable procedure was also developed for the ODT test bench in Garching to measure the exact degree of contamination on detectors, in order to be able to quantify that critical problem. Contamination happens under vacuum conditions because of out-gassing of unsuitable materials. If this occurs near the CCD detector, having the lowest surface temperature, unwanted condensations form at its surface. The two graphs illustrate this QE decrease:
n
2. RE
A reproduciblmaterials usedmaterials havesamples withprocedure useTable 2. Firstsolvent, then pressurized nmaximum pos
Figure 2&3: QE decrease on CCD due to contaminatio
CIPE AGAINST CONTAMINATION
e method to avoid this hazard is now available [1]. The list of in ESO’s cryostats is given in Table 1. Suitable and bad been obtained as a result of ESO’s program of categorizing
a mass-spectrometer [3] and from a NASA list [2]. The d to achieve ultra-clean cryostats component is given below in all components are hand cleaned with paper and a suitable two times washed in an ultrasonic bath, eventually dried with itrogen or paper and later baked in a vacuum oven to the sible temperature. At last the CCD cryostat is assembled with
gloves under clean-room conditions. Moreover investigations of a comparison between zeolith and charcoal, the ingredient of the cryostat's molecular sieve have been done. Coconut charcoal is the better material to prevent organic contamination. Regenerated zeolith absorbs water better. Only if the geometry of the cryostat is unfavor-
Figure 4: Cryostat assembly in clean-room
Ultra-clean CCD Cryostats 3
Material, manufacturer Curing in vacuum
Max. service temperature
Ethanol, propanol, acetone - 40 ºC Cleaning agents Tickopur-soap, Bandelin - 85 ºC
Fiberglass HGW 2372, Ferrozell - 130 ºC
Glue Master Bond EP21TCHT-1 1-2 h / 93 ºC -269 to +204 ºC
Heating resistors
Caddock, MP821, TO-220 power package, 20 W
- 175 ºC
Internal connectors
Harwin connectors, Glass-filled polyester UL94V-0
- 85 ºC
O-ring Viton 70A/80A, Busak & Shamban
- 200 ºC
PCBs Kapton with copper 4 h / 120 ºC 130 ºC (250 ºC)
Ultra high vacuum grease
Fluorinated Fomblin grease: FM 090, Pfeiffer
- 100 ºC
Vacuum connectors
Hermetic connect., HirelcoIntern. connectors, Microdot
- 95 ºC
Zeolith 18 h / 200 ºC 350 ºC Sorption pumps Coconut active charcoal 18 h / 20 ºC 100 ºC (?)
Thermal fuse R&S: 176-9148 - 75 ºC
ZIF-Socket Glass-filled polyphenylene sulfide (PPS), 3M
18 h / 105 ºC 105 ºC
Table 1: Used materials for ultra-clean cryostats in addition to stainless steel, aluminum, glass, INVAR, gold coating, oxygen free copper and electronic SMD components
able, contamination with water ice formation on the CCD is unavoidable. This happens, if a large warm surface “looks” directly at the CCD detector. Finally, a specially designed clean-room was built for the proper handling and assembly of the cleaned parts in order to get a very clean CCD cryostat. With all these measures, we have now for several years in all (kept cold) CCD cryostats at the telescopes been able to avoid contamination.
3. REFERENCES
[1] S. Deiries, E. Hummel: How ESO achieves ultra-clean cryostats, Webpage, http://www.eso.org/projects/odt/contamination/clean.html
4 S. Deiries, O. Iwert, C. Cavadore, C. Geimer, and E. Hummel [2] NASAs: Materials And Processes Technical Information System on the web: http://map3.msfc.nasa.gov/mapweb/page7.html [3] O. Schütz, S. Deiries: Out-gassing of CCD components in the vacuum at http://www.eso.org/projects/odt/contamination/msreport/index.html
Washing Vacuum baking
(10-2 mBar)
Material
Possible solvent
Han
d cl
eani
ng
1. U
ltras
onic
wat
er
bath
with
Tic
kopu
r de
terg
ent a
t 80º
C
2. U
ltras
onic
bat
h w
ith w
ater
(80º
C) o
r no
n ul
tras
onic
bat
h w
ith so
lven
t
Max
imum
tem
p.
Min
. dur
atio
n
Modified epoxy material Acetone no 30 min. 30 min. 120 ºC 16 h
Metals parts (Al and steel) Acetone yes 30 min. 30 min. 180 ºC 16 h
ZIF-sockets Alcohol no 30 min. 30 min. 150 ºC 72 h
Raw boards Alcohol no 30 min. 30 min. 120 ºC 72 h
Electro-nic
boards Soldered PCB Alcohol yes no no 85 ºC 72 h
EEV no yes no no 80 ºC 72 h
Tektronix no no no no 55 ºC 72 h
CCDs
MIT/LL no yes no no 60 ºC 72 h
Vacuum connectors Alcohol no 30 min. 30 min. 85 ºC 16 h
Welded inner tank Acetone yes 30 min. 30 min. 85 ºC 72 h
CFC inner tank structure Alcohol yes 30 min. 30 min. 85 ºC 72 h
Painted shields no no no no 120 ºC 72 h
Glued components Alcohol yes no no 120 ºC 72 h
VITON O-rings Alcohol yes 30 min. 30 min. 120 ºC 16 h
Zeolith (sorption pump) - no - - >180ºC 16 h
Active charcoal Alcohol no - - 100 ºC 16 h
Vacuum pipes Acetone yes 30 min. 30 min. 180 ºC 16 h
Vacuum valve Alcohol yes - - 120 ºC 16 h Fittings
Vacuum gauge Alcohol yes - - 85 ºC 16 h
Table 2: Treatment of components