97
UHF P25 TRANSCEIVER TK-5310 © 2006-12 PRINTED IN JAPAN B51-8779-00 (S) 570 SERVICE MANUAL GENERAL ............................................................... 2 SYSTEM SET-UP ................................................... 2 REALIGNMENT ...................................................... 3 INSTALLATION .................................................... 10 DISASSEMBLY FOR REPAIR .............................. 11 CIRCUIT DESCRIPTION ....................................... 16 SEMICONDUCTOR DATA ................................... 22 COMPONENTS DESCRIPTION ........................... 24 PARTS LIST .......................................................... 26 EXPLODED VIEW ................................................. 39 Does not come with antenna. Antenna is available as an option. PACKING .............................................................. 41 ADJUSTMENT ..................................................... 42 TERMINAL FUNCTION ........................................ 62 PC BOARD TX-RX UNIT (X57-7250-XX) ........................... 66 SCHEMATIC DIAGRAM ....................................... 74 INTERCONNECTION DIAGRAM ......................... 86 BLOCK DIAGRAM ................................................ 87 LEVEL DIAGRAM ................................................. 90 SPECIFICATIONS .............................. BACK COVER Helical Antenna (KRA-23: Option) Main cabinet (A02-3875-01) Knob (16CH) (K29-9323-03) Knob (Volume) (K29-9322-03) TK-5310 K, K4 TK-5310 K2, K5 TK-5310 K3, K6 CONTENTS Knob (PTT) (K29-9328-02) Key top (EMG) (K29-9319-03) Main cabinet (4key) (A02-3877-11) Knob (16CH) (K29-9323-03) Knob (Volume) (K29-9322-03) Knob (PTT) (K29-9328-02) Key top (EMG) (K29-9319-03) Main cabinet (DTMF) (A02-3879-11) Knob (16CH) (K29-9323-03) Knob (Volume) (K29-9322-03) Knob (PTT) (K29-9328-02) Key top (EMG) (K29-9319-03) Helical Antenna (KRA-23: Option) Helical Antenna (KRA-23: Option) Key top (DTMF) (K29-9321-13) Key top (4key) (K29-9320-03)

UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

Page 1: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

UHF P25 TRANSCEIVER

TK-5310© 2006-12 PRINTED IN JAPANB51-8779-00 (S) 570

SERVICE MANUAL

GENERAL ............................................................... 2

SYSTEM SET-UP ................................................... 2

REALIGNMENT ...................................................... 3

INSTALLATION .................................................... 10

DISASSEMBLY FOR REPAIR .............................. 11

CIRCUIT DESCRIPTION ....................................... 16

SEMICONDUCTOR DATA ................................... 22

COMPONENTS DESCRIPTION ........................... 24

PARTS LIST .......................................................... 26

EXPLODED VIEW................................................. 39

Does not come with antenna. Antenna is available as an option.

PACKING .............................................................. 41

ADJUSTMENT ..................................................... 42

TERMINAL FUNCTION ........................................ 62

PC BOARD

TX-RX UNIT (X57-7250-XX) ........................... 66

SCHEMATIC DIAGRAM....................................... 74

INTERCONNECTION DIAGRAM ......................... 86

BLOCK DIAGRAM ................................................ 87

LEVEL DIAGRAM ................................................. 90

SPECIFICATIONS ..............................BACK COVER

Helical Antenna(KRA-23: Option)

Main cabinet(A02-3875-01)

Knob (16CH)(K29-9323-03)

Knob (Volume)(K29-9322-03)

TK-5310 K, K4 TK-5310 K2, K5 TK-5310 K3, K6

CONTENTS

Knob (PTT)(K29-9328-02)

Key top(EMG)(K29-9319-03)

Main cabinet(4key)(A02-3877-11)

Knob (16CH)(K29-9323-03)

Knob (Volume)(K29-9322-03)

Knob (PTT)(K29-9328-02)

Key top(EMG)(K29-9319-03)

Main cabinet(DTMF)(A02-3879-11)

Knob (16CH)(K29-9323-03)

Knob (Volume)(K29-9322-03)

Knob (PTT)(K29-9328-02)

Key top(EMG)(K29-9319-03)

Helical Antenna(KRA-23: Option)

Helical Antenna(KRA-23: Option)

Key top(DTMF)(K29-9321-13)

Key top(4key)(K29-9320-03)

Page 2: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

2

GENERAL / SYSTEM SET-UP

Document CopyrightsCopyright 2006 by Kenwood Corporation. All rights

reserved.No part of this manual may be reproduced, translated,

distributed, or transmitted in any form or by any means,electronic, mechanical, photocopying, recording, or other-wise, for any purpose without the prior written permissionof Kenwood.

DisclaimerWhile every precaution has been taken in the preparation

of this manual, Kenwood assumes no responsibility forerrors or omissions. Neither is any liability assumed for dam-ages resulting from the use of the information containedherein. Kenwood reserves the right to make changes to anyproducts herein at any time for improvement purposes.

INTRODUCTION

SCOPE OF THIS MANUALThis manual is intended for use by experienced technicians

familiar with similar types of commercial grade communicationsequipment. It contains all required service information for theequipment and is current as of the publication date. Changeswhich may occur after publication are covered by either ServiceBulletins or Manual Revisions. These are issued as required.

ORDERING REPLACEMENT PARTSWhen ordering replacement parts or equipment information, the

full part identification number should be included. This applies to allparts : components, kits, or chassis. If the part number is not known,include the chassis or kit number of which it is a part, and a sufficientdescription of the required component for proper identification.

PERSONAL SAFETYThe following precautions are recommended for personal safety:

• DO NOT transmit until all RF connectors are verified se-cure and any open connectors are properly terminated.

• SHUT OFF and DO NOT operate this equipment near elec-trical blasting caps or in an explosive atmosphere.

• This equipment should be serviced by a qualified technician only.

SERVICEThis transceiver is designed for easy servicing. Refer to

the schematic diagrams, printed circuit board views, andalignment procedures contained within.

NOTEYou must use KPG-95D version 5.00 or later for this trans-ceiver. KPG-95D versions earlier than version 5.00 will notwork properly.

SYSTEM SET-UP

Merchandise received

License and frequency allocated by FCC

Choose the type of transceiver

Transceiver programming

Are you using the optional antenna?

Are you using the speaker microphone?

A personal computer (IBM PC or compatible), programming interface (KPG-36/36A), USB adapter(KCT-53U), and programming software (KPG-95D) are required for programming.(The frequency, and signaling data are programmed for the transceiver.)

Frequency range (MHz) RF power Type LCD 4-key DTMF keypad

TX/RX 450~520 4W TK-5310 K No No No

NoTX/RX 450~520 4W TK-5310 K2 Yes Yes

TX/RX 450~520 4W TK-5310 K3 Yes Yes Yes

NoTX/RX 380~470 4W TK-5310 K4 No No

TX/RX 380~470 4W TK-5310 K5 Yes Yes No

YesTX/RX 380~470 4W TK-5310 K6 Yes Yes

YESKRA-23 or KRA-27

Helical antennaNO

NO

(Option)

(Option)

YESKMC-25

Speaker microphoneor

KMC-38GPSGPS speaker microphone

Are you using the voice guide & storage unit?

NO (Option)

YESVGS-1

Delivery

See page 10

Model & Unit X57-725X-XXFrequency range Remarks LCD 4-key

DTMFDestination (Market code) 0-10 0-11 0-12 0-13 0-14 0-15 keypad

K - - -K2 450~520 MHz -

TK-5310K3 1st IF:49.95MHz

K4 LOC:50.4MHz - - -K5 380~470 MHz -K6

Page 3: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

3

REALIGNMENT

1. Modes 2. How to Enter Each Mode

Mode Operation

User mode Power ON

Panel test mode ∗2 Press and hold the [Side3] and [PTT] keys

while turning the transceiver power ON and

then release the [PTT] key first.

PC mode Received commands from PC

Panel tuning Press the [Side3] key, in Panel test mode

mode ∗2

Firmware Press and hold the [Side3] and [PTT] keys

programming mode while turning the transceiver power ON and

then release the [Side3] key first.

Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

while turning the transceiver power ON and

then release the [Side2] key first.

Self programming Press and hold the [Side2] and [PTT] keys

mode ∗2 while turning the transceiver power ON and

then release the [PTT] key first.

Firmware version Press and hold the [Side3] key while turning

information ∗2 the transceiver power ON.

Clock adjustment Press and hold the [Orange] and [PTT] keys

mode ∗2 while turning the transceiver power ON and

then release the [Orange] key first.

Transceiver Press and hold the [Side1] and [PTT] keys

information mode ∗2 while turning the transceiver power ON and

then release the [PTT] key first.

3. Panel Test Mode

(K2, K3, K5 and K6 models only)

Setting method refer to ADJUSTMENT.

4. Panel Tuning Mode

(K2, K3, K5 and K6 models only)

Setting method refer to ADJUSTMENT.

User mode

Panel test mode ∗1

Firmware version information ∗1

Panel tuning mode ∗1

Data programming mode

PC test mode PC tuning mode

PC mode

Clone mode ∗1

Firmwareprogramming mode

Clock adjustment mode ∗1

Transceiver information mode ∗1

Self programming mode ∗1

Mode Function

User mode For normal use.

Panel test mode ∗1 Used by the dealer to check the fundamen-

tal characteristics.

Panel tuning mode ∗1 Used by the dealer to tune the transceiver.

PC mode Used for communication between the

transceiver and PC (IBM compatible).

Data programming Used to read and write frequency data and

mode other features to and from the transceiver.

PC test mode Used to check the transceiver using the PC.

This feature is included in the FPU.

See panel tuning.

Firmware Used when changing the main program of

programming mode the flash memory.

Clone mode ∗1 Used to transfer programming data from

one transceiver to another.

Self programming Frequency, signaling and features write to

mode ∗1 the transceiver.

Firmware version Used to confirm the internal firmware

information ∗1 version.

Clock adjustment Used by the dealer to adjust date and time.

mode ∗1

Transceiver Used to confirm the transceiver firmware

information mode ∗1 version.

∗1 : K2, K3, K5 and K6 models only

∗2 : K2, K3, K5 and K6 models only

Page 4: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

4

REALIGNMENT

5. PC Mode

5-1. PrefaceThe transceiver is programmed by using a personal com-

puter, programming interface (KPG-36/36A), USB adapter(KCT-53U) and programming software (KPG-95D).

The programming software can be used with an IBM PCor compatible. Figure 1 shows the setup of an IBM PC forprogramming.

5-2. Connection procedure1. Connect the transceiver to the computer using the inter-

face cable and USB adapter (When the interface cable isKPG-36A, the KCT-53U can be used.).

Notes:• You must install the KCT-53U driver in the computer to use

the USB adapter (KCT-53U).• When using the USB adapter (KCT-53U) for the first time,

plug the KCT-53U into a USB port on the computer withthe computer power ON.

2. When the POWER switch on, user mode can be enteredimmediately. When PC sends command the transceiverenter PC mode, and “PROGRAM” is displayed on the LCD.When data transmitting from transceiver, the red LED is lights.When data receiving to transceiver, the green LED is lights.

Notes:• The text message are displayed for K2, K3, K5 and K6 mod-

els only.• The data stored in the computer must match the "Model

Name and Market Code" when it is written into theEEPROM and flash memory.

5-3. KPG-36/KPG-36A description

(PC programming interface cable: Option)The KPG-36/36A is required to interface the transceiver to

the computer. It has a circuit in its D-sub connector (KPG-36: 25-pin, KPG-36A : 9-pin) case that converts the RS-232Clogic level to the TTL level.

The KPG-36/36A connects the universal connector of thetransceiver to the RS-232C serial port of the computer.

5-4. KCT-53U description (USB adapter : Option)The KCT-53U is a cable which connects the KPG-36A to a

USB port on a computer.When using the KCT-53U, install the supplied CD-ROM

(with driver software) in the computer. The KCT-53U driverruns under Windows 2000 or XP.

5-5. Programming software KPG-95D descriptionThe KPG-95D is the programming software for the trans-

ceiver supplied on a CD-ROM. This software runs under MS-Windows 98, ME, Windows 2000 or XP on an IBM-PC orcompatible machine.

The data can be input to or read from the transceiver andedited on the screen. The programmed or edited data can beprinted out. It is also possible to tune the transceiver.

6. Firmware Programming Mode

6-1. PrefaceFlash memory is mounted on the transceiver. This allows

the transceiver to be upgraded when new features are re-leased in the future. (For details on how to obtain the firm-ware, contact Customer Service.)

6-2. Connection procedureConnect the transceiver to the personal computer (IBM

PC or compatible) using the interface cable (KPG-36/36A) andUSB adapter (KCT-53U : when the interface cable is KPG-36A, the KCT-53U can be used.). (Connection is the same asin the PC Mode.)

6-3. Programming1. Start up the firmware programming software (Fpro.exe).2. Set the communications speed (normally, 115200 bps)

and communications port in the configuration item.3. Set the firmware to be updated by File name item.4. Press and hold the [Side3] and [PTT] keys while turning

the transceiver power ON and then release the [Side3] keyfirst. Then, the orange LED on the transceiver lights andthe baud rate is displayed as follows according to the posi-tion of the Concentric switch.

A: PROGRAM 115200 bpsB: PROGRAM 57600 bpsC: PROGRAM 19200 bps

Since the baud rate is normally set to 115200 bps, changethe Concentric switch to "A".

5. Check the connection between the transceiver and thepersonal computer, and make sure that the transceiver isin the Program mode.

6. Press “write” button in the window. When the trans-ceiver starts to receive data, the [PG] display lights.

Fig. 1

IBM-PC

KPG-95D

KPG-36 or KPG-36A orKPG-36A + KCT-53UIllustration is KPG-36.

KPG-36

Transceiver

PC

D-SUB(25-pin)

Transceiver

PC

KPG-36A

D-SUB(9-pin)

Transceiver

PC

KPG-36A

KCT-53U

USB

Page 5: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

5

REALIGNMENT

7. If writing ends successfully, the checksum is calculatedand a result is displayed.

8. If you want to continue programming other transceivers,repeat steps 4 to 7.

Notes:• This mode cannot be entered if the Firmware Program-

ming mode is set to Disable in the Programming software.• The text message are displayed for K2, K3, K5 and K6

models only.• These transeivers use firmware versions F4.00 or later.

When using firmware versions earlier than version F4.00, a“Check connection” error message will appear on theLCD. Firmware versions earlier than version F4.00 will notwrite to the transceiver.

6-4. Baud rate change1. Change baud rate by changing the Concentric switch posi-

tion. The baud rates are assigned to positions of the Con-centric switch as follows:

A: PROGRAM 115200 bps (The LED lights orange)B: PROGRAM 57600 bps (The LED blinks orange)C: PROGRAM 19200 bps (The LED blinks green)

2. If you press the [Side1] switch (top of left side) while thebaud rate (such as “PROGRAM 115200 bps") is displayed,the checksum is calculated, and a result is displayed. Ifyou press the [Side1] switch again while the checksum isdisplayed, the baud rate (such as “PROGRAM 115200bps") is redisplayed.

Notes:• Normally, write in the high-speed mode.• The text message are displayed for K2, K3, K5 and K6

models only.

7. Clone Mode (K2, K3, K5 and K6 models only)

Programming data can be transferred from one transceiverto another by connecting them via their external universal con-nectors. The operation is as follows (the transmit transceiveris the source and the receive transceiver is a target).

The following data cannot be cloned.• Tuning data• Embedded message with password• Model name data• ESN (Electronic Serial Number) data• Network file data (P25)

Key guide on the "INPUT PASSWORD" display.• CNF([A] key): The password confirmation• DEL([B] key): Delete the least digit from the current pass-

word number (Press and hold to delete allpassword numbers)

• SET([D] key): Determine the least digit of the password number

1. Press and hold the [Side2] and [PTT] keys while turning thetransceiver power ON and then release the [Side2] key first.If the Read authorization password is set to the transceiver,the transceiver displays “CLONE LOCK”. If the password isnot set, the transceiver displays “CLONE MODE”.

2. When you enter the correct password, and “CLONE MODE”is displayed, the transceiver can be used as the cloningsource. The following describes how to enter the password.

3.• How to enter the password using the keypad (K3 and

K6 models only);If the [D] key is pressed while "CLONE LOCK" is displayed,the Read authorization password input screen (INPUTPASSWORD) is displayed.If one of keys 0 to 9 is pressed while "INPUT PASSWORD"is displayed, the pressed number is displayed on the LCD.Each press of the key shifts the display in order to the left.When you enter the password and press the [A] or []key, “CLONE MODE” is displayed if the entered pass-word is correct. If the password is incorrect, “CLONELOCK” is redisplayed.

• How to enter the password using the [Side2] and[Side3] keys (K2, K3, K5 and K6 models);If the [D] key is pressed while "CLONE LOCK" is displayed,the Read authorization password input screen (INPUTPASSWORD) is displayed.If the [Side2] key or [Side3] key is pressed while "INPUTPASSWORD" is displayed, the number (0 to 9) flashes onthe LCD. When you press the [D] key, the currentlyselected number is determined. If you press the [A] keyafter entering the password in this procedure, “CLONEMODE” is displayed if the entered password is correct. Ifthe password is incorrect, “CLONE LOCK” is redisplayed.

4. Power ON the target transceiver.5. Connect the cloning cable (part No. E30-3325-05) to the

universal connectors on the source and target.6. Press the [Side1] or [A] key on the source while the source

displays “CLONE MODE”. The data of the source is sentto the target. While the target is receiving the data, “PRO-GRAM” is displayed. When cloning of data is completed,the source displays “END”, and the target automaticallyoperates in the User mode. The target can then be oper-ated by the same program as the source.

7. The other target can be continuously cloned. When the[Side1] or [A] key on the source is pressed while thesource displays “END”, the source displays “CLONEMODE”. Carry out the operation in step 4 to 6.

Notes:• Cannot be cloned if the password (overwrite password) is

programmed to the target.• Cannot be cloned if the checksum in the Network File area of

the source transceiver and the target transceiver is different.• "Model Name and Market Code" must be same to clone

the transceiver. However, it may be unable to clone thetransceiver depending on the enhanced features settings.(Refer to the FPU for the enhanced features details.)

• Under certain conditions, clone mode cannot be activatedeven if the clone mode of the source transceiver is set toenable. Refer to the FPU for more details.

Cloning cable(E30-3325-05)

Fig. 2

Page 6: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

6

REALIGNMENT

8. Self Programming Mode(K2, K3, K5 and K6 models only)

Write mode for frequency data and signaling etc. To beused ONLY by the authorized service person maintaining theuser's equipment. After programming, reset the FPU to the"Self- Programming" disabled mode. Transceivers CANNOTbe delivered to the end-user in the self-programming mode.

The following setup items in the channels programmed bythe FPU can be changed using the self-programming mode.The addition of new channel and the deletion of channel thathas already been programmed by the FPU cannot beperformed using the self-programming mode.• RX frequency• TX frequency• Channel type• TX mode (When the channel type is selected "MIXED".)• Channel spacing• RX signaling• TX signaling• RX NAC• TX NAC• Talkgroup list number

Note:The personality will be also changed when the above-mentioned items is changed. (Refer to the FPU for thepersonality details.)

Key guide on the "INPUT PASSWORD" display.• CNF([A] key): The password confirmation• DEL([B] key): Delete the least digit from the current pass-

word number (Press and hold to delete allpassword numbers)

• SET([D] key): Determine the least digit of the passwordnumber

8-1. Enter to the self programming modePress and hold the [Side2] and [PTT] keys while turning

the transceiver power ON and then release the [PTT] keyfirst. Ignoring whether the Read authorization password isset or not, "INPUT PASSWORD" appears.

If the Read authorization password is not set to the trans-ceiver, "SELF PROG MODE" is displayed on the LCD when the[A] key is pressed while "INPUT PASSWORD" is displayed.

If the password is set to the transceiver, "SELF PROGMODE" is displayed on the LCD when you enter the correctpassword while "INPUT PASSWORD" is displayed.

For the password input method, see "7.Clone Mode”step 3 described on page 5.

Note :This mode (self programming mode) cannot be set whenit has been disabled with the FPU.

8-2. Data WritingIf the [Side3] key is pressed while Zone/Channel mode is

displayed, new data is written into memory. "Writing" is dis-played while the transceiver is writing data.

No. Setup item Display Remarks1 Select ZONE [**] -CH *** Zone : 1~50

Zone/Channel ZONE ** -CH [***] CH : 1~2502 RX frequency RX Freq Receive frequency3 TX frequency TX Freq Transmit frequency4 Channel type CH Type ANALOG/P25/MIXED5 TX mode TX Mode ANALOG/P256 Channel spacing CH Space 25.0kHz/12.5kHz (When the Channel type is selected "ANALOG" or "MIXED".)

P25 12.5kHz/12.5kHz (When the Channel type is selected "P25".)7 RX Signaling RX Sig Receive QT/DQT8 TX Signaling TX Sig Transmit QT/DQT9 RX NAC RX NAC *** 000~FFF (Hexadecimal) Note : “F7F” cannot be set.10 TX NAC TX NAC *** 000~FFF (Hexadecimal) Note : “F7E” and “F7F” cannot be set.11 Talkgroup list number TG List No. *** 1~250

The setup items for self programming mode are as follows.

Page 7: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

7

Item Zone-Channel RX Frequency TX Frequency Channel Type TX Mode Channel Spacing RX Signaling TX SignalingKey

[A] Go to the next item

[B]Zone/Channel 5kHz/6.25kHz/1MHz

UnusedQT/DQT(N)/DQT(I)/OFF

switching step switching switching

[C] Zone/Channel 1 step down ANALOG/P25/MIXED ANALOG/P25 Channel spacing Signaling downdown switching(Back) switching(Back) switching(Back)

[D] Zone/Channel 1 step up ANALOG/P25/MIXED ANALOG/P25 Channel spacing Signaling upup switching(Forward) switching(Forward) switching(Forward)

[Side3] Data Unused ON/OFF Unused 1 step/Standardwriting switching switching

Keypad[0]~[9]

Unused Go to the direct enter mode UnusedGo to the direct enter mode

(K3 and K6 (After selecting signaling type)models only)

Key operation

Item RX NAC TX NAC TG List No.Key

[A] Go to the next item

[B] Delete the least digit from the current number Unused (Press and hold to delete all numbers.)

[C] Unused TG Listnumber down

[D] Determine the least digit TG Listnumber up

[Side2] Increment a number in the specified digit Unused[Side3] Decrement a number in the specified digit UnusedKeypad Add a digit to the current number

(K3 and K6 How to enter the “A” ~ “F” is follows.Unused

models only) A : Press [2] with PTT B : Press [5] with PTT C : Press [8] with PTTD : Press [0] with PTT E : Press [#] with PTT F : Press [*] with PTT

REALIGNMENT

• Direct enter mode

Item RX Frequency TX Frequency RX Signaling TX SignalingKey

[A] Return to non-direct enter mode

[B] UnusedChange the type of signaling andreturn to non-direct enter mode

[C] Unused

[D] Delete the least digit from the current number(Press and hold to delete all numbers.)

[Side3] ON/OFF switching at TX Frequency UnusedKeypad

Add a digit to the current number[0] ~ [9]Keypad

Return to non-direct enter mode[*]

Keypad Delete the least digit from the current number[#] (Press and hold to delete all numbers.)

Page 8: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

8

REALIGNMENT

Self programming mode flow chart

TX NAC

[A]

RX NAC

[A]

TX signaling

[A][A]

RX signaling

[A]

[A] [A]

[A]*1

*2

[A]

TX frequency

RX frequency

[A] When the [Side3] key is pressed, new data is written into memory.

[A]

Zone/Channel

[A]

Read authorization password entry (6 digits)[A]

[Side2] + [PTT] + POWER ON Release [PTT]

[TX frequency] : Other than "OFF"[Channel type] : "MIXED"

[TX frequency] : Other than "OFF"[Channel type] : "ANALOG" or "MIXED"[TX mode] : "ANALOG"

[TX frequency] : "OFF" [TX frequency] : Other than "OFF"[Channel type] : "P25" or "MIXED"If [Channel type] is set to "MIXED", [TX mode] must be set to "P25".

[Channel type] : "ANALOG" or "MIXED"[A][Channel type] : "P25"

[TX frequency] : "OFF"[Channel type] : "ANALOG" or "P25"

[TX frequency] : "OFF"[Channel type] : "P25" or "MIXED"

[A][TX frequency] : "OFF"[Channel type] : "ANALOG"

[A][Channel type] : "ANALOG"

[A][TX frequency] : "OFF"Talkgroup ID List Amount : 0or[TX frequency] : Other than "OFF"[Channel type] : "MIXED"[TX mode] : "ANALOG"Talkgroup ID List Amount : 0

[A]Talkgroup ID List Amount : 0

[Channel type] : "P25" or "MIXED"

[Channel type] : "P25" or "MIXED"Talkgroup ID List Amount must not be 0.

Self programming mode

Input Password

OFF QT

OFF

Zone selection

P25

Channel selection

Talkgroup list number

[A]

[A]

[A]

[Side 3]

[B]

DQT N

[B]

[B]

DQT I

[B]

[B] [B] [B]

[B]

ANALOGChannel type[C]/[D]

P25ANALOGTX mode[C]/[D]

Channel spacing 12.5kHz25.0kHz[C]/[D]

12.5kHz

*1 [Channel type] : "ANALOG" or "MIXED"

*2 [Channel type] : "P25"

P25 12.5kHz[C]/[D]

[C]/[D]

MIXED[C]/[D]

OFF QT DQT N

[B]

DQT I

Page 9: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

9

11. Transceiver Information Mode

(K2, K3, K5 and K6 models only)

Use this function to confirm the transceiver firmware version.

1. Press and hold the [Side1] and [PTT] keys while turningthe transceiver power ON and then release the [PTT] keyfirst.

2. The transceiver firmware version appears on the LCD.3. To exit the transceiver information mode, turn the trans-

ceiver power OFF.

REALIGNMENT

9. Firmware Version Information(K2, K3, K5 and K6 models only)

Press and hold the [Side3] key while turning the transceiverpower ON and then keep pressing and holding the [Side3] key,the firmware version information appears on the LCD.

10. Clock Adjustment Mode (K2, K3, K5 and K6 models only)

10-1. Flow chart of operation

[Orange] + [PTT] + Power ON Release [Orange]

MINUTE

HOUR

DAY

MONTH

YEAR

[A]

[A]

[A]

[A]

[A]

[Side2] and [Side3] keys or [C] and [D] keys

[Side2] and [Side3] keys or [C] and [D] keys

[Side2] and [Side3] keys or [C] and [D] keys

[Side2] and [Side3] keys or [C] and [D] keys

[Side2] and [Side3] keys or [C] and [D] keys

Completion

Page 10: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

10

5. Insert the VGS-1 connector (CN1) into the connector(CN609) of the TX-RX PCB.

6. Reinstall the cover using the 4 screws removed in step 1.

Note:

You must setup using the KPG-95D.

INSTALLATION

Voice Guide & Storage Unit (VGS-1:Option)

Installing the VGS-1 unit in the transceiver1. Remove the 4 screws from the cover.2. Remove the cover by inserting the tip of a pair of tweezers

into the screw hole of the cover and prying it open.

3. Remove the OPTION PCB from the connector (CN609) ofthe TX-RX PCB.

4. Attach two cushions to the VGS-1 as shown in the figure 3.

Note:

Be sure not to cover the VGS-1 connector (CN1) with thecushion.

Cushion(G13-1995-04)20X30X1.0mm

Cushion(G13-1974-04)21X21X1.0mm

VGS-1

CN609

VGS-1

CN1

CN609

OPTION PCB

Fig. 1

Fig. 2

Fig. 3

Page 11: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

11

DISASSEMBLY FOR REPAIR

Disassembly Procedure

Removing the front case from the chassis.1. Remove the rear panel with a flat-head screwdriver.

Insert the screwdriver between the rear panel (right side)and the chassis (the place next to the """ mark shown onthe chassis), push it in the direction of the arrow z, andremove the right side of the rear panel. Repeat the aboveaction for the left side of the rear panel x.

2. Remove the four screws c and universal connector capv.

3. Lift the battery pack release latch on the bottom of thechassis b and remove the chassis from the front case.

Notes:

• Lift the chassis from the front case slowly and carefully. Ifthe chassis is lifted suddenly, the SP/MIC FPC may bepulled and the connector may become damaged.

• Handle the main packing with care. It is likely to collectdust and dirt.

4. Remove the SP/MIC FPC from the CONTROL PCB con-nector (CN713). n

Removing the CONTROL PCB (X57-725 B/5)from the chassis.

1. Remove the six screws m.

2. On the reverse side of the CONTROL PCB ,, remove thecord ASSY and each FPC from the connectors (CN700,CN800 (K2, K3, K5 and K6 models only), CN803, CN804)of the CONTROL PCB.

Removing the TX-RX PCB (X57-725 A/5) fromthe chassis.

1. Remove the 14 screws ..2. Remove the universal connector FPC from the TX-RX PCB

connector (CN606) /.3. Insert the two tips of a pair of tweezers into the two holes

in the bottom of the shield plate of the TX-RX PCB, firmlysqueeze the tweezers to hold the shield plate, thenremove the TX-RX PCB Ω.

4. Remove the coaxial cables from the two connectors(MAIN (CN204), UNIV (CN205)) of the TX-RX PCB ≈.

z

x

Rear panel""" mark

""" mark

c

c

v

n

bCN713

Chassis

Battery packrelease latch

SP/MIC FPC

Front case

m

m

m

CONTROL PCB

Chassis

CN800

CN700

CN803CN804

Cord ASSY

,

CN606

UNIV(CN205)

MAIN(CN204)

TX-RX PCB

Chassis

Universalconnector FPC

.

Ω

.

..

..

. ≈

/

Page 12: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

12

DISASSEMBLY FOR REPAIR

Removing the top panel from the chassis.1. Remove the volume knob ç and channel knob √.2. Remove the concentric switch knob ∫.3. Remove the volume torque-up packing ~ using a pair of

tweezers.4. Remove the nuts from the volume knob, channel knob

and antenna receptacle.5. Remove the top panel µ.

Notes:

• Before removing the top panel, set the lever switch to the"-" position (circle painted in white) ≤.

• Each of the volume knob, channel knob and antenna re-ceptacle on the top panel has an O-ring. Take care not tolose them after removing the panel.

Removing the TOP PCB (X57-725 C/5) from thechassis.

1. Remove the two screws ≥.2. Lift the TOP PCB and remove the VOL/CH FPC ÷ and

CONTROL-TOP FPC 21 from the two connectors (CN902,CN903) of the TOP PCB.

Precautions for Reassembly Installing the VOL/CH FPC and CONTROL-TOP

FPC on the TOP PCB

1. Remove the volume z and channel switch x from thechassis.

2. Position the coaxial cable connecting the ANT PCB andTX-RX PCB as shown in the figure below.

3. Pass the coaxial cable c of the antenna receptaclethrough the round hole of the hardware fixture v, theninsert it into the coaxial connector (MAIN (CN204)) of theTX-RX PCB.

4. Pass the volume, channel switch, VOL/CH FPC andCONTROL-TOP FPC through hardware fixture holes, thenbring the hardware fixture into contact with the chassisand fix it with a screw b.

Note:

The projections of the volume and channel switch pedes-tals must protrude from the square holes of the hardwarefixture.

5. Fix the antenna receptacle with the two screws n.6. Fix the hardware fixture with a screw m.

O-ring

ç

µ

≤~

CN902

TOP PCB

CN903

÷

21

CONTROL-TOPFPC VOL/CH FPC

The projection of the volume pedestal

The projection of the channelswitch pedestal

Aline the coaxial cable connecting the ANT PCB and TX-RX PCB as shown in the figure.

zx

MAIN(CN204) c

v

b

n

m

Page 13: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

13

2. Fit the two tabs on the right side of the holder c and thetwo tabs on the left side of the holder v into theCONTROL PCB.

Note:

Take care that the FPC is not caught when fitting the twotabs on the right side of the holder.

3. Insert the FPC into the CONTROL PCB connector (CN802)b.

Main Packing (G53-1637-04) Installation Procedure

1. Hook the packing (coated with silicon oil) in the uppergroove of the chassis z, then fit the packing into thelower groove of the chassis x.

Note:

Ensure that the chassis grooves and packing are free fromdirt and dust.

2. Fit the packing into the grooves on both sides of thechassis c. (Fit the packing into the groove in the chassisby tracing it lightly with your fingers.)

Note:

To remove the packing from the chassis groove, use aresin adjustment bar or other such device. If the packingis pried with a sharp metallic tool, such as tweezers, thepacking may become damaged.

3. Verify that the packing fits snuggly into the groove of thechassis.

DISASSEMBLY FOR REPAIR

7. Insert the VOL/CH FPC , and the CONTROL-TOP FPC .into the connectors (CN902, CN903) of the TOP PCB.

8. Fix the TOP PCB with a screw /.9. Fix the TOP PCB with a screw Ω.

TX-RX PCB Installation Procedure1. Insert the coaxial cable of the antenna receptacle into the

coaxial connector (CN204) of the TX-RX PCB z and thecoaxial cable of the ANT PCB into the coaxial connector(CN205) of the TX-RX PCB x.

2. Grasp both sides of the lower part of the TX-RX PCB, tiltthe TX-RX PCB and install the chassis so that the PTT FPCc, CONTROL-TOP FPC v and universal connector FPCb are not caught n.

3. Fix the TX-RX PCB with the 14 screws.

LCD ASSY Installation Procedure (K2, K3, K5 and

K6 models only)

1. Fold the LCD ASSY FPC to the back of the holder z sothat the FPC is between the two tabs on the right side ofthe holder x.

CN902

CN903

,

.

CN205

CN204

Grasp both sides of the lower part of the TX-RX PCB

z

x

c

v

n

b

LCD ASSY FPCtab

tab

zx

CN802

b

Main packing

z

c

c

x

tab

CONTROL PCB

c

vv

c

Page 14: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

14

2. Tighten the two screws from the TX-RX PCB side.

3. Firmly tighten the hexagon screws of the GND terminal.

Installation Procedure during Parts

Replacement

Attaching the Sheet (G10-1338-04, J99-0383-14)to the Front Case Speaker and Installation ofthe Packing (G53-1633-04)

1. Attach a new fiber sheet z (G10-1338-04) so that itsconvex fits the hollow of the front case x.

2. Attach a new pressure sensitive adhesive sheet c (J99-0383-14) so that its convex fits the hollow of the frontcase v.

3. Remove the separation sheet from the pressure sensitiveadhesive sheet with a pair of tweezers b.

4. Fit the packing n (G53-1633-04) into the front casespeaker.

Note:

Fit the packing into the hollow of the case so that the twolow-height places in the convex of the packing are posi-tioned on the lower side m.

5. Verify that the packing does not ride on the rib of the case.

Installing a new LCD ASSY to the holder (K2,K3, K5 and K6 models only)

1. Remove the separation paper (brown) from the new sheetz x, and attach the sheet to the surface of the holder c.

2. Remove the protection sheets attached to both sides ofthe new LCD ASSY.

DISASSEMBLY FOR REPAIR

Top Packing (G53-1638-04) Installation Procedure1. Ensure that the hardware fixture is first secured to the

chassis.2. Hook the packing (coated with silicon oil) in the upper left

groove of the chassis z, then fit the packing into the rightgroove of the chassis. x

Notes:

• Verify that the chassis grooves and packing are free fromdirt and dust.

• To remove the packing from the chassis groove, use aresin adjustment bar or other such device. If the packingis pried with a sharp metallic tool, such as tweezers, thepacking may become damaged.

3. Verify that the packing fits snuggly into the groove of thechassis.

Volume Torque-up Packing (G53-1628-04)Installation Procedure

Insert the packing using a pair of tweezers so that thehollow of the packing fits the convex of the panel z.

Screw sequence for mounting the batteryterminal block to the chassis.

Attach the battery terminal block to the chassis asdescribed in the following procedure.

1. Loosely fix the hexagon screws of the GND terminal tothe chassis (enough so that the hexagon screws do notmove).

Volume torque-up packing z

GND terminal

Two screws

n

c

v bz

m

x

Top packing

Hardware fixture

z

x

Page 15: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

15

3. Remove the separation paper (white) from the sheet instep 1 v, then attach the LCD ASSY b to the sheet.

4. Attach two pieces of double-sided adhesive tape n to theback of the holder and remove the separation paper.

5. Remove the protection sheet (transparent) attached toone side of the new filter m , and remove the protectionsheet (yellow) from the other side ..

6. Attach the filter from step 5 to the back of the holder.7. Attach the new cushion / so that it fits to the corner of

the holder convex.

Preparation when Replacing the Cord ASSY(X42-3270-10)

Cut the tip of the FPC on the side on which "TX-RX" isstamped when replacing the cord ASSY.

Procedures when Replacing the Top Panel1. Insert the O-ring z into the lever switch part of the new

top panel.2. Apply grease to the base of the shaft of the lever knob x

and install the lever knob so that it is in the "-" position(circle painted in white) on the top panel c.

3. Pass the hardware fixture v through the shaft and installit onto the top panel.

4. Apply grease to between the two holes in the hardwarefixture v.

5. Install the hardware fixture b so that it is inserted into thehole on the left side of the hardware fixture v.

z

z

x

c

c

v

n mn

n

,

.

n

b

b/

/

CUT

TX-RX CONT

Cord Assy(X42-3270-10)

6. Fix the two hardware fixtures with the hexagon nut n.7. Apply bond (Three Bond 1401C) to the tip of the lever

knob shaft and the surface of the hexagon nut m.

Volume Knob and Channel Knob Parts Replace-ment

Since the volume knob consists of two components, aknob z and a spacer x, replace and reinstall these twoparts at the same time.Since the channel knob consists of three components, aknob c, a 16CH display seal v and a spacer b, replaceand reinstall these three parts at the same time.

Procedure when replacing the universal connectorFPC (J82-0097-25)

When assembling a new universal connector FPC, insertthe FPC into the chassis hole by gently bending the FPCas shown in the figure.

Apply grease to between the two holes in the hardware fixture.

Apply bond (Three Bond 1401C) to the tip of the lever knob shaft and the surface of the hexagon nut.

Top panel

Inserted into the hole on the left side of the hardware fixture.

Apply grease to the base of the shaft of the lever knob.

z

v

m

b

n

x

c

Volume Knob Channel Knob

zcb

vx

DISASSEMBLY FOR REPAIR

UniversalConnector

Do not bend the FPC at a sharp angle.

Universal connector FPC

Wrong

UniversalConnector

Bend the FPC gently.

Universal connector FPC

Universal connector FPC(J82-0097-25)

Right

Page 16: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

16

CIRCUIT DESCRIPTION

1. OverviewThis transceiver is a UHF/FM/P25 portable transceiver

designed to operate in the frequency range of 450 to520MHz (K, K2, K3) or 380 to 470MHz (K4, K5, K6).

The unit consists of receiver, transmitter, phase-lockedloop (PLL) frequency synthesizer, base band parts, powersupply, and control circuits.

2. Frequency ConfigurationThe receiver is a double-conversion superheterodyne

using first intermediate frequency (IF) of 49.95MHz andsecond IF of 450kHz. Incoming signals from the antenna aremixed with the local signal from the PLL circuit to producethe first IF of 49.95MHz.

This is then mixed with the 50.4MHz second localoscillator output to produce the 450kHz second IF. Thissignal is detected to give the demodulated signal in the DSP.

The transmit signal frequency is generated by the PLLVCO, and modulated by the signal from the DSP. It is thenamplified and fed to the antenna.

3. Receiver System

3-1. Front-end RF AmplifierThe signal is passed through an antenna matching coil,

where the high-frequency components are amplified by aMOS FET(Q301). The signals are then fed into band-passfilter that uses varactor diode tuning to reject unwantedsignal components, and is fed to the 1st mixer.

3-2. 1st MixerThe 1st mixer uses the GaAs IC (IC302). The 1st mixer

mixes the signal with the 1st local oscillator frequency fromthe VCO, and converts it to the 1st IF (49.95MHz).

The signal then passes through monolithic crystal filter(XF300) to remove unnecessary nearby frequencycomponents. The signal from the MCF is used as the 1st IFsignal.

3-3. IF AmplifierThe 1st IF signal is amplified by the IF amplifier (Q302) and

fed into the FM IC (IC304). The IF signal is then mixed withthe 2nd local oscillator frequency of 50.4MHz to generate the

Fig. 1 Frequency configuration

ANTTX/RX : 450~520MHz(K, K2, K3)TX/RX : 380~470MHz(K4, K5, K6)

ANTSW

RFAMP

PAAMP

TXAMP

1st MIX MCF

VCXO

49.95MHz

CF450kHz

MIXIF AMP

AFAMP

SP

16.8MHz

50.4MHz

x3

400.05~470.05MHz(K, K2, K3)330.05~420.05MHz(K4, K5, K6)

450~520MHz(K, K2, K3)380~470MHz(K4, K5, K6)

PLLVCO

FPGAA/DD/ADSP

MICAMP

MIC

2nd IF of 450KHz. The 450KHz signal is then passed througha ceramic filter (CF300) and fed back into IC304 for additionalamplification.

3-4. Wide/ Narrow/ P25 Switching Circuit

Narrow and Wide and P25 settings can be made for eachchannel by switching the ceramic filters CF303 (Wide),CF302 (Narrow), CF301 (P25).

The Wide and Narrow and P25 data is output from pin51(WN) and pin52 (VN) of CPU (IC5).

When a Wide data (VN : low level, WN : high level) isreceived, the 450KHz signal is passed through a ceramic filter(CF303). When a Narrow data (VN : low level, WN : low level)is received, the 450KHz signal is passed through a ceramicfilter (CF302). When a P25 data (VN : high level, WN : highlevel) is received, the 450KHz signal is passed through aceramic filter (CF301).

If the 450kHz signal is a FM signal(Wide, Narrow), thesignal is detected by a ceramic discriminator (CD300). AFsignal is fed to CODEC(IC454), the AF level is adjusted and itis output from 15pin of IC454. Q304 turns on/off with theWide/Narrow data and the IC304 detector output level ischanged to maintain a constant output level during Wide orNarrow signals.

If the 450kHz signal is an P25 signal, the signal is preparedby the buffer amplifier (IC308) and fed to FPGA (IC457). TheP25 signal is A/D-converted by the FPGA and DSP (IC8), andis performed P25 demodulation.

The AF signal is output from 15pin of CODEC (IC454).

1st Local OSC

BPF BPF 1stLNA MIXERQ301

TUNE2

IC302

MCFXF300

49.95MHz

IF AMPQ302

Q303

2nd Local OSC

FM IC

IC304

TriplerX3CF300

TUNE1

X30016.8MHzVCXO

WN WN

VNVNCF303

CF302

CF301P25

Narrow

Wide

IC303 IC305

IC306 IC307CF300

16.8MHz

VCXOX300

x3

Q30350.4MHz

49.95MHz

450kHz

IC304FM IC

DET

P25

CD

CD300AF

VN WN

L

H HL H

LWideNarrow

P25

Filter

Fig. 2 Receiver section

Fig. 3 Wide/Narrow/P25 switching circuit

Page 17: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

17

CIRCUIT DESCRIPTION

3-5. Audio Amplifier Circuit• AF signal

The AF signal from CODEC (IC454) is amplified by IC456and goes through IC458.

The AF signal goes through a DAC (IC462), an AF amplifier(IC705), and an AF switch (IC701), and is routed to audiopower amplifier (IC702), where the signal is amplified andoutput to the internal speaker.

• Audio circuit

CODEC (IC454) extracts the audio signal from the receivesignal in the detection circuit in FM mode. The signal is thendeemphasized and output as a decoded audio signal in P25mode.

LPF (IC456) removes quantization noise from the audiosignal output of the CODEC.

The switch (IC458) stops the audio signal of the CODEC toprevent the mixing of BEEP, voice announcement and audiosignal when the BEEP or voice announcement is output fromthe CPU. If an optional scrambler board is installed, the audiopath is adjusted so that the audio signal goes through thescrambler board.

DAC (IC462) controls the voltage amplitude level of theaudio signal according to the volume position of thetransceiver. This determines the volume level output fromthe speaker.

The amplifier (IC705) amplifies the audio signal so that theaudio signal level at the final stage amplifier is appropriate.

The volume levels of the 8Ω internal speaker and 16Ωexternal speaker are matched using the EXT AFC.

The switch (IC701) adjusts the signal path so that theaudio signal is output to the audio amplifier (IC703) forexternal speakers when optional external speakers areconnected. If no external speakers are connected, the audiosignal is output to the audio amplifier (IC702) for the internalspeaker.

IC702 and IC703 output is BTL (Bridge Tied Load).

• AF control

Speaker switching is performed by the CPU (IC5) usingINT AFC or EXT AFC. First, the logic level at the speakersswitching terminal (SSW) on the universal connector is fed tothe CPU. The CPU then outputs data based on this input.

When there is no SP-MIC installed, this logic levelbecomes high. When the INT AFC is high, the EXT AFC goeslow, so the AF signal is only fed to the amplifier for theinternal speaker (INT SP) of IC702.

However, when a SP-MIC has been connected, this logiclevel becomes low, so the INT AFC goes low and the EXTAFC goes high. In this case, the AF signal is fed only toamplifier for the external speaker (EXT SP) of IC703.

3-6. Squelch CircuitIt amplifies the demodulated noise signal from FM IC

(IC304) after filtering through BPF circuit. Then, the amplifiedsignal is converted to DC signal by the detection circuit. Theconverted signal is fed to the CPU (IC5).

4. Transmitter System

4-1. Audio Band CircuitThe audio band circuit of the transmitter system consists

of the following:• Microphone (Main)• Microphone (Sub)• N/C amplifier (Noise canceling mic amplifier) (IC705)• Switch (Int/ext) (Q455)• Switch (Mic mute) (Q452)• AGC (IC452, D450, D451)• Switch (Scrambler board) (Q454)• Switch (VGS-1) (IC450)

This transceiver has two types of microphones: main andsub. The main microphone is located at the front of thecabinet and the sub microphone is located at the rear of thecabinet. The audio signal input from these microphones issynthesized by the N/C amplifier (IC705). The audio signalfrom the main microphone is synthesized in normal phaseand the audio signal from the sub microphone is synthesizedin opposite phase. So if the same audio signal is applied in thesame phase to the main and sub microphones, it is cancelledby the N/C amplifier. If audio signal is input to only the main orsub microphone, it is not cancelled, but output from the N/Camplifier.

This prevents ambient noise from entering the audio bandcircuit at the next or subsequent stages.

When an optional external speaker microphone isinstalled, the Int/ext switch (Q455) cuts off the audio signalfrom the main and sub microphones and sends only the audiosignal from the external microphone to the next stage.

The microphone mute switch (Q452) cuts off audiosignals from the main, sub and external microphones.

AGC (IC452, D450, D451) is an amplifier that reduces gainautomatically by greatly increasing the attenuation when theaudio signal of a certain level or higher is present. It controlsthe gain so that the audio signal input to the CODEC (IC454)is not clipped.

Fig. 4 Audio circuit diagram

Fig. 5 Squelch circuit

IC451BPF AMP

Q460Noise AMP

D453DET

IC5CPU

BEEPS/SCSW

TX-RX (X57-725 A/5) CONTROL (X57-725 B/5)BEEP/voice announce

EXT AFC EXT AFC

INT SP

IC454CODEC

IC456LPF

IC462DAC

IC705AMP

IC701SW

universal connectorEXT SP

Scrambler board

IC8DSP

INT AFC

IC702AMP

IC703AMP

IC458SW

Page 18: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

18

CIRCUIT DESCRIPTION

If an optional scrambler board is installed, the switch(Q454) adjusts the signal path so that the audio signal is inputto the CODEC through the scrambler board.

If the optional VGS-1 (Voice Guide & Storage unit) isinstalled, the switch (IC450) will adjust the signal path so thatthe audio signal from the microphone is output to the VGS-1and the audio signal from the VGS-1 is input th the CODEC.

The audio signal is input to the CODEC (base band circuit)through the above path.

4-2. Base Band CircuitThe base band circuit of the transmitter system consists

of the following:• CODEC (IC454)• DSP (IC8)• LPF (IC456)• Buffer (IC459)• DAC (IC462)• Amplifier (IC463)

The audio signal output from the base band circuit isconverted to digital data of a sampling frequency of 48 kHzand a quantization resolution of 16 bits by the CODEC(IC454). This digital data is sent to the DSP (IC8), and voicesignals of 300 Hz or lower and frequencies of 3 kHz or higherare cut off and an audio range 300 Hz to 3 kHz is extracted.

The audio signal is then pre-emphasized in FM mode andsynthesized with the signals, such as QT and DQT, asrequired, and is then output from the CODEC. In P25 mode,the audio signal is converted to the C4FM base band signaland output from the CODEC. The DTMF and MSK base bandsignals are also generated by the DSP and output by theCODEC.

LPF (IC456) removes quantization noise from the baseband signal output from the CODEC.

The buffer (IC459) sets the base band signal level to theDAC input range.

The DAC (IC462) assigns the base band signal to the VCO(Q107) and VCXO (X100).

At this time, the level output according to the transmitcarrier is fine-adjusted according to the modulation methodof FM Wide, FM Narrow and P25.

4-3. Transmit Signal Amplification Circuit

(From T/R switch to Final amplifier) The transmit signal passing through the T/R switch

(D200) is amplified to approx. 50 mW by the two transistoramplification circuits (Q200, Q210). The transmit signaloutput from Q210 passes through an attenuator to improvehigh-frequency signal matching is amplified by the driveamplifier (Q202) and applied to the final amplifier (Q205). Thesignal applied to the final amplifier is amplified by the finalamplifier so that the antenna output is 4 W (1 W for LowPower).

4-4. High-Frequency Signal Switch Circuit

(From Antenna switch to ANT output)The transmit signal output from the final amplifier (Q205)

passes through the antenna switch (D202, D203) and LPF,and goes into the SPDT switch (IC202, IC203) which changesthe antenna connector (CN204) and the universal connector(CN205).

The transmit signal passing through the output changeswitch passes through the surge protection HPF andspurious removing LPF and then goes to the antennaconnector (CN204) or the universal connector (CN205),specified by the SPDT switch (IC202, IC203).

4-5. APC CircuitThe APC circuit detects the current of the drive amplifier

(Q202) and final amplifier (Q204) during transmission andcontrols the output power by controlling the current.

It detects the current using R220 and R222 and applies adrop voltage between both resistors during transmission toAPC (IC201). It controls the transmission current of the driveamplifier and final amplifier so that it is constant bycomparing this current with the reference voltage outputfrom pin 7 of IC200. The reference voltage input to pin 5 ofIC200 is output from the DAC (IC462). High/Low poweroutput is set according to the DAC output voltage.

Fig. 6 Audio band and Base band circuit

MIC(MAIN)

EXT.MIC

MIC(SUB)

MSW/CTSMM

IC705 Q455SW

Q452SW AGC-AMP

IC452LPF

D450,D451DET

Scrambler board

SCSW

VGS-1 VATS

MIC

N/CAMP

IC462DAC

Q454SW

IC8DSP

IC454CODEC

IC450SW

IC456LPF

IC459BUFF

IC463AMP

X100VCXO

Q107VCO

Page 19: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

19

CIRCUIT DESCRIPTION

5. PLL Frequency SynthesizerThe PLL Frequency Synthesizer consists of the following

components:• VCXO (X100)• VCO (Q106, Q107)• Doubler (Q110, Q111)• PLL IC (IC101)• Local switch (D200, D308)

5-1. VCXO (X100)VCXO (X100) generates a reference frequency of 16.8

MHz for the PLL frequency synthesizer. This referencefrequency is applied to pin 8 of the PLL IC (IC101).

The VCXO oscillation frequency is fine-adjusted bycontrolling the voltage applied to pin 1 of the VCXO with DAC(IC462). It is also controlled with pin 1 of the VCXO if theoutput from VCXO is modulated.

5-2. VCOThere is a RX VCO and a TX VCO.The TX VCO (Q107) generates a transmit carrier and the

RX VCO (Q106) generates a 1st local receive signal.The oscillation frequency is as follows.K, K2, and K3 types

Q106 : 400.050 ~ 449.995MHzQ107 : 450.000 ~ 520.000MHz

K4, K5, and K6 typesQ106 : 330.050 ~ 379.995MHzQ107 : 380.000 ~ 470.000MHz

The VCO oscillation frequency is determined by onesystem of operation switching terminal "T/R" and twosystems of voltage control terminals "C/V" and "V-assist".

The operation switching terminal, "T/R", is controlled by thecontrol line (T/R) output from the CPU (IC5). When the T/Rlogic is low, the VCO (Q107) outputs the transmit carrier andwhen it is high, VCO (Q106) outputs a 1st local receive signal.

The voltage control terminals, "CV" and "V-assist", arecontrolled by the PLL IC (IC101) and CPU (IC5) and the outputfrequency changes continuously according to the appliedvoltage. “V-assist” is controlled directly by a microcomputerto change the VCO oscillation frequency at high speed.However, its accuracy is low and the VCO frequency cannotbe matched accurately with the desired transmit carrier orthe 1st local receive signal. “CV” is controlled by the PLL andis used to accurately match (look) the desired frequency ofthe VCO oscillation frequency. For the modulation inputterminal, "MOD", the output frequency changes according to

the applied voltage. This is used to modulate the VCO output."MOD" works only when "T/R" is low.

5-3. Doubler (Q110, Q111)The doubler (Q110, Q111) extracts the twice harmonic

component from the signal output from the VCO. This twiceharmonic component is then fed into pin 5 of the PLL IC.

5-4. PLL IC (IC101)PLL IC compares the differences in phases of the VCO

oscillation frequency and the VCXO reference frequency,returns the difference to the VCO CV terminal and realizesthe "Phase Locked Loop" for the return control. This allowsthe VCO oscillation frequency to accurately match (lock) thedesired frequency.

When the frequency is controlled by the PLL, thefrequency convergence time increases as the frequencydifference increases when the set frequency is changed. Tosupplement this, the CPU is used before control by the PLLIC to bring the VCO oscillation frequency close to the desiredfrequency. As a result, the VCO CV voltage does not changeand is always stable at approx. 2.5 V.

The desired frequency is set for the PLL IC by the CPU(IC5) through the 3-line "LE", "DAT", "CLK" serial bus. Whetherthe PLL IC is locked or not is monitored by the CPU throughthe “UL” signal line. If the VCO is not the desired frequency(unlock), the "UL" logic is low.

5-5. Local Switch (D200, D308)The connection destination of the signal output from the

VCO is changed with the diode switch (D200) that iscontrolled by the transmission power supply, 5T, and thediode switch (D308) that is controlled by the receive powersupply, 5R.

If the 5T logic is high, it is connected to a send-side pre-pre-drive (Q200). If the 5T logic is low, it is connected to areceive-side mixer (IC302).

Fig. 8 PLL block diagram

T/R

IC100 V-assistDC AMP

LEDATCLK

Q109 Q112 D200 to pre-pre-driveLPF

Q106,Q107VCO BUFF BUFF SW

UL CV

IC5

IC101 D308 to 1st mixer

(Q200)

(IC302)

CPU

PLLQ110,Q111

Doubler SW

MOD

X100 IC462VCXO DAC

4-6. Temperature Protection CircuitThe temperature protection circuit reduces the APC

voltage when the temperature of Q204 rises, to preventthermal destruction of the final amplifier (Q204). The CPU

D200T/R SW

Q202Drive Amp

Q204Final Amp D202,D203

ANT SW

IC201APCR220

+B

R222APC SW

Q200Pre Pre Drive Amp

Q210Pre Drive Amp

Attenuator

IC203SPDT

IC202SPDT CN204

CN205LPF

(IC5) detects the temperature with a thermistor (TH200) tocontrol the reference voltage to the APC circuit.

Fig. 7 Transmitter circuit

Page 20: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

20

CIRCUIT DESCRIPTION

6. Control CircuitThe control circuit consists of CPU (IC5) and its peripheral

circuits. It controls the TX-RX unit and transfers data to theControl unit. IC5 mainly performs the following;1) Switching between transmission and reception by PTT

signal input.2) Reading system, zone, frequency, and program data from

the memory circuit.3) Sending frequency program data to the PLL.4) Controlling squelch on/off by the DC voltage from the

squelch circuit.5) Controlling the audio mute circuit by decode data input.6) Transmitting tone and encode data.

6-1. Memory CircuitMemory circuit consists of the CPU (IC5) and a flash

memory (IC6). A flash memory has a capacity of 16M bits andcontains the transceiver control program for the CPU. It alsostores the data for transceiver channels and operating param-eter that are written by the FPU. This program can be easilywritten from an external devices.

The EEPROM (IC3) stores the last channel data, the scanon status, and other parameters.

Flash memoryNote : The flash memory stores the data that is written bythe FPU (KPG-95D), and firmware program (User mode, Testmode, Tuning mode, etc.). This data must be rewritten whenreplacing the flash memory.

EEPROMNote : The EEPROM stores tuning data (Deviation, Squelch,etc.).Realign the transceiver after replacing the EEPROM.

Real-time clockThe clock function is based on real-time clock IC (IC2).

When the power supply is off, it is backed up by an internalsecondary lithium battery

6-2. LCD (K2, K3, K5 and K6 models only)The LCD is controlled using the bus lines on the connector

(CN800) of the control unit (X57 B/5).The LCD contrast voltage is corrected using IC800. The

thermometry result used by the temperature IC (IC1) iscorrected by the CPU (IC5), and the contrast voltage is outputas a pulse ripple from the LCDV terminal (pin 28) of the CPU.The filter then smoothens the voltage which in turn is inputinto pin 3 of IC800.

6-3. Temperature Detection CircuitThe temperature detect ion circuit detects the

temperature using a temperature IC (IC1) and corrects thethermal characteristic change of the squelch or LCD.

6-4. Key Detection CircuitKeys are detected using three shift registers (IC801,

IC802, IC803).The KIN signal that is normally pulled down goes high

when any key is pressed.

6-5. Low Battery WarningThe battery voltage is divided using R22 and R23 and is

detected by the CPU (IC5). When the battery voltage fallsbelow the voltage set by the Low battery warningadjustment, the red LED blinks to notify the operator that it istime to replace the battery. If the battery voltage falls evenmore (approx. 5.8V), a beep sounds and transmission stops.

Low battery warning Battery condition

The red LED blinks during The battery voltage is low but

transmission. the transceiver is still usable.

The red LED blinks and The battery voltage is low and

the warning tone beeps while the transceiver is not usable to

the PTT switch is pressed. make calls.

6-6. Battery Type DetectionThe transceiver automatically detects the battery type,

measuring the resistance between the S-terminal and GNDterminal on the battery pack and changes the suppliedvoltage to the S-terminal as below. The microprocessor thendetects the battery type.

6-7. VOXThe VOX function can be used only with an external

microphone.The VOX (Voice Operated Transmission) function detects

voice input to the microphone and automatically switchesbetween transmission and reception. However, if ascrambler board is installed (Extended Function VoiceScrambler is selected with FPU), VOX does not operate.

Fig. 9 Memory circuit

CPU EEPROM

FLASH

IC5

IC6

IC3

Fig. 10 Clock diagram

IC454CODEC

IC457FPGA

IC8DSP

IC5CPU

IC453(2/3,3/3)9.216MHz

9.216MHz

18.432MHz

18.432MHz

18.432MHz

IC455X450VCXO

IC453(1/3)

Battery type Input voltage of S-terminal Resistor value

Battery case 0~0.2V Short

Li-ion battery 0.85~1.02V 47 kΩ

Ni-Cd battery 3.23~3.37V Open

Ni-MH battery 1.71~1.95V 150 kΩ

Page 21: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

21

CIRCUIT DESCRIPTION

If the microphone input exceeds a certain level,transmission automatically begins. If the input falls below acertain level, the transceiver automatically returns to receivemode.

The transceiver realizes this function using DSP (IC8).

6-8. DSPThe DSP circuit consists of a DSP (IC8), a CODEC (IC454)

and processes the base band signal. The DSP operates on anexternal clock of 9.216MHz (the same as the CPU), the I/Osection operates at 3.3V and the core section operates at1.5V. The DSP carries out the following processes:• C4FM encoding• Analog FM pre-emphasis/de-emphasis• Vocoder (IMBE) processing between audio codec and

modulation/demodulation• CAI processing, such as error correction encoding• QT/DQT encoding/decoding• DTMF encoding/decoding• MSK encoding/decoding• 2-tone encoding/decoding• Compressor/expander processing• Transmit/receive audio filtering processing• VOX processing• Microphone amplifier AGC processing• Audio mute processing• Modulation level processing

6-9. FPGAThe FPGA(IC457) I/O section operates at 3.3V. and the core

section operates at 2.5V. The FPGA has the following function.• Demodulation (C4FM,CQPSK)• Shift register(8CH)• Level convert Buffer amplifier(5V3.3V)(9CH)• Generates 1.536MHz for the demodulation and CODEC.

7. Power Supply CircuitThe power supply voltage (+B) is supplied from the

battery terminal of the TX-RX unit (X57 A/5) and is thenpassed through the fuse (F600).

If +B voltage is detected by the voltage detection IC(IC706) and it is above 5.6V, then the 3V regulator (IC704) CEpin becomes high and the 3.0V power source turns ON.Additionally, when the VOL SW is ON, the 3.6V DC/DCconverter (IC710) CE pin becomes high and the 3.6V powersource turns ON.

The output from the 3.6V DC/DC converter (IC710)provides the power source for three regulators (IC707,IC708, IC711) and the 1.5V DC/DC converter (IC709).

The voltage output from the 1.5V DC/DC converter(IC709) is detected by the 33A SW (Q712).

When the CE pin of the 3.3V regulator (IC708) is high, the33A power source turns on.

When the 3.6V power source turns on, the 5V regulator(IC712) CE pin becomes high and 5M is supplied with thepower source.

The three regulators (IC707, IC708, IC711) and the DC/DCconverter (IC709) start the CPU, DSP, FPGA, etc. After theCPU starts up, it begins controlling two regulators (IC601,IC600) with the 5CC and PWR signals.

When the Power SW (Q602) is turned on with the PWRsignal, the 15V DC/DC converter (IC713) starts up. IC712,IC601, and IC600 is supplied from +B.

The output from IC600 is switched between 5R (which isturned on while receiving) and 5T (which is turned on whiletransmitting), and is controlled by the CPU.

The output from of the 5V regulator (IC610) is controlled byQ604 and is used as a power source for 5MCS, for an optionalaccessory which is connected to the universal connector.

8. Signaling Circuit

8-1. Encode (QT/DQT/DTMF/2-tone/MSK)Each signaling data signal of QT, DQT, DTMF, 2-tone and

MSK is generated by the DSP circuit, superposed on a modu-lation signal and output from pin 16 of the CODEC (IC406).

The modulation balance of the QT/DQT signal is adjustedby the D/A converter(IC411) and the resulting signal is routedto the modulation input of the VCO and VCXO (X301).

The each deviation of the TX QT, DQT, DTMF, 2-tone andMSK tone is adjusted by changing the output level of theCODEC and the resulting signal is routed to VCO and VCXO.The RX DTMF tone is output from pin 15 of the CODEC,passes through the receive audio signal system, and is out-put from the speaker.

8-2. Decode (QT/DQT/DTMF/2-tone/MSK)The audio signal is removed from the FM detection signal

sent to the DSP circuit and the resulting signal is decoded.

9. Compander CircuitThe term “compander” means compressor and expander.

The compander reduces noise by utilizing a compressor andan expander.

The transceiver contains DSP(IC8) to perform this opera-tion. The transceiver compander can be turned on or off usingthe FPU.

CPU, FlashROM,EEPROM, VCXO,

FPGA (I/O)

DSP (I/O)

RTC

DSP (Core)

FPGA (Core)

LCDVCO

Drive, Final AMPDC/DC, AVR

CE

3.6V

IC704AVR IC

Q713Detect

SW

Q71233A SW

IC710DC/DC

IC706Detect

+B3A FuseF600

BATT

5M

5MCS

5R

5T

33M

33A

28M

15D

25D

+B

15V

5C

5CC

CE

CE

5RC

5TC

5MC

CE

CE

CE

CE

CE

CE

CE

CE

CE

CE

PWR

Q602Power

SWSB

IC5CPU

VOLSW

IC707AVR IC

Q6015R SW

Q6005T SW

Q6045M CS SW

IC708AVR IC

IC709DC/DC

IC711AVR IC

IC601AVR IC

IC610AVR IC

IC600AVR IC

IC712AVR IC

IC713DC/DC

Fig. 11

Page 22: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

22

SEMICONDUCTOR DATA

CPU:30625MGP346HU (TX-RX unit IC5)

Pin Port Name I/O FunctionNo.

Pin Port Name I/O FunctionNo.50 HLDA - No connection51 WN O Wide/Narrow ceramic filter switching

(L:Narrow, H:Wide)52 VN O Wide,Narrow/P25 ceramic filter

switching (L:P25, H:Analog)53 EXTIM I External option control port from

universal connector54 SCSW O When the scrambler board is installed,

the route of AF is changed.(L:Scrambler on, H:off)

55 BCLK O Bus control (Base clock output)56 RD O Bus control (Read)57 BHE - No connection58 WR O Bus control (Write)59 TGL0 I Lever switch input 060 TGL1 I Concentric switch input 161 TGL2 I Concentric switch input 262 CS3 O LCD CS63 CS2 O Flash memory CS64 CS1 O DSP CS65 CS0 O Flash memory CS66 A19 O Address bus 1967 A18 O Address bus 1868 A17 O Address bus 1769 A16 O Address bus 1670 A15 O Address bus 1571 A14 O Address bus 1472 A13 O Address bus 1373 A12 O Address bus 1274 A11 O Address bus 1175 A10 O Address bus 1076 A9 O Address bus 977 INAFC O Internal AF control (L:Off, H:On)78 CH_A I Rotary switch input 179 CH_B I Rotary switch input 280 CH_C I Rotary switch input 381 CH_D I Rotary switch input 482 VCC2 - Power supply input83 A8 O Address bus 884 VSS3 - Power supply input85 A7 O Address bus 786 A6 O Address bus 687 A5 O Address bus 588 A4 O Address bus 489 A3 O Address bus 390 A2 O Address bus 291 A1 O Address bus 192 A0 O Address bus 093 EXAFC O External AF Control (L:Off, H:On)94 HINT I(INT4) DSP HINT interrupt95 INT3 - Not used96 PTT I PTT input97 EXSP I External speaker install check98 DRST O DSP reset output

1 BATT DET I(A/D) Battery detection terminal2 NC(ANEX0) I NC (For expansion A/D)3 ASSIST O(D/A) VCO control4 VOICE O(D/A) Voice output5 SOE O Shift register OE6 UL I PLL unlock input7 DAT O Common data8 CLK O Common clock9 SDA I/O EEPROM data10 BYTE I Use as 8bit data bus (Vcc)11 CNVSS I Use as memory expansion mode (Vss)12 STRB O Shift register CS13 NC - No connection14 RESET I Reset input15 XOUT - No connection16 VSS1 - Power supply input17 XIN - Clock input, 9.216MHz(18.432MHz/2)18 VCC1 - Power supply input19 NMI I NC20 RTCDT I/O RTC data I/O21 PSW I(INT1) Power switch detection

(L:Power on, H:Power off)22 INTRA I(INT0) RTC interrupt input23 LD O DAC LD24 BEEP O(PWM) Beep output25 LE O PLL CS26 BSFT O Beat shift output

(L:Shift, H:Not shift)27 KEY/PLAY I TX key input (for ANI board),

Play Input (for VGS)28 LCDV O LCD contrast adjustment29 INH I Audio inhibit input (for ANI board),30 AUXI I AUX input (for ANI board),31 TCNT I Tone control input (for ANI board),32 BEEPS O Beep switch(L:Unmute, H:Mute)33 TXD1 O(UART) UART(for VGS)34 VCC1 - Power supply input35 RXD1 I(UART) UART(for VGS)36 VSS2 - Power supply input37 BUSY I BUSY input(for VGS)38 RTSM/EXTO O UART(3.3V5V)/External option

output port to universal connector39 TXDM O(UART) UART(3.3V5V)40 RXDM I(UART) UART(5V3.3V)41 DSRM I UART(5V3.3V)42 CTSM I UART(5V3.3V)43 A20 O Flash memory A1944 KES O Key counter CS45 KIN I Key counter return46 MODEL I Model detection47 RDY I Bus control (Ready)48 ALE - No connection49 HOLD I Bus control (Hold)

Page 23: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

23

1 STRB I Latch clock input2 DATA I Serial data input3 CLK I Serial clock input

4-7 Q1-Q4 O Key counter8 VSS - GND9 QS O Serial data output

10 Q’S O NC11-14 Q8-Q5 O Key counter

15 OE I Output enable control input16 VDD - Power supply input

1 STRB I Latch clock input2 DATA I Serial data input3 CLK I Serial clock input

4-7 Q1-Q4 O Key counter8 VSS - GND9 QS O Serial data output

10 Q’4 O NC11-14 Q8-Q5 O Key counter

15 OE I Output enable control input16 VDD - Power supply input

1 STRB I Latch clock input2 DATA I Serial data input3 CLK I Serial clock input

4-7 Q1-Q4 O Key counter8 VSS - GND9 OS O NC

10 NC O NC11 Q8 O Audio amplifier switch12 Q7 O Backlight switch13 Q6 O TX LED switch14 Q5 O Busy LED switch15 OE I Output enable control input16 VDD - Power supply input

99 FRST O Flash memory reset output100 NC O No connection101 D7 I/O Data bus 7102 D6 I/O Data bus 6103 D5 I/O Data bus 5104 D4 I/O Data bus 4105 D3 I/O Data bus 3106 D2 I/O Data bus 2107 D1 I/O Data bus 1108 D0 I/O Data bus 0109 5TC O 5T control (L:Off, H:On)110 5RC O 5R control (L:Off, H:On)111 5CC O 5C control (L:Off, H:On)112 APCSW O APC switch output (L:Off, H:On)113 CAE3 I Man-down switch input114 VU I V/U detection115 MM O MIC mute output (L:Unmute, H:Mute)116 PWR O Power control output

(L:Power off, H:Normal)117 WPA I(A/D) PA temperature compensation118 SQ I(A/D) Analog SQ input119 CV I(A/D) VCO CV input120 RSSI I(A/D) RSSI input121 TEMP I(A/D) Temperature input122 BATT I(A/D) Battery level input123 REM I(A/D) KMC-25 PF1/PF2 key, KVL3000 input124 AVSS - A/D converter power supply input terminal125 VOL I(A/D) Volume level input126 VREF - A/D converter reference voltage input

terminal127 AVCC - A/D converter power supply input

terminal128 T/R O TX/RX switch (L:TX, H:RX)

1 STRB I Latch clock input2 DATA I Serial data input3 CLK I Serial clock input4 Q1 O OPT55 Q2 O OPT46 Q3 O OPT17 Q4 O OP_MAN8 VSS - GND9 QS O Serial data output10 Q'S O NC11 Q8 O OPT612 Q7 O OPT213 Q6 O CHGIO:UNIV 9p I/O Switching14 Q5 O OPT315 OE I Output enable control input16 VDD - Power supply input

SEMICONDUCTOR DATA

Pin Port Name I/O FunctionNo.

Pin Port Name I/O FunctionNo.

Shift Register:BU4094BCFV (TX-RX unit IC606)

Shift Register:BU4094BCF (Control unit IC801)

Pin Port Name I/O FunctionNo.

Shift Register:BU4094BCF (Control unit IC802)

Pin Port Name I/O FunctionNo.

Shift Register:BU4094BCF (Control unit IC803)

Pin Port Name I/O FunctionNo.

Page 24: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

24

COMPONENTS DESCRIPTION

Ref. No. Part name Description

TX-RX unit (X57-7250-XX A/5) Ref. No. Part name Description

IC1 IC Temperature DETIC2 IC RTC ICIC3 IC EEPROMIC4 IC Voltage DETIC5 IC CPUIC6 IC FLASH ROMIC7 IC CS ANDIC8 IC DSP

IC100 IC DC AMP for VCO tuneIC101 IC PLL ICIC200 IC DC AMPIC201 IC Auto Power Control

IC202,203 IC SPDTIC300,301 IC DC AMP for BPF

IC302 IC DBMIC303 IC MultiplexerIC304 IC FM IC

IC305~307 IC MultiplexerIC308 IC BufferIC450 IC Switch (VGS TX I/O)IC451 IC OP AMP (5V reference/SQL AMP)IC452 IC OP AMP (TX AGC AMP/Buffer AMP)IC453 IC D-type flip flopIC454 IC CODECIC455 IC BufferIC456 IC OP AMP (TX LPF/RX LPF)IC457 IC FPGAIC458 IC Switch (RX scrambler SW/BEEP SW)IC459 IC OP AMP (TX buffer AMP/RX buffer AMP)IC460 IC Switch (VGS RX I/O)IC461 IC RX summing AMPIC462 IC D/A ConverterIC463 IC OP AMP (TX MOD AMP/3.3V reference)IC600 IC Voltage regulator (5T/5R)IC601 IC Voltage regulator (5C)IC602 IC MultiplexerIC603 IC Buffer

IC604,605 IC UART switchIC606 IC Shift registerIC607 IC Bus switch (8ch)

IC608,609 IC Bus switch (2ch)IC610 IC Voltage regulator (5MCS)Q100 Transistor Ripple filterQ101 FET S33A switchQ102 FET SwitchQ103 FET Buffer for CVQ104 Transistor Ripple filterQ105 FET T/R switch

Q106,107 Transistor VCO oscillationQ108 FET T/R switch

Q109~112 Transistor Buffer AMPQ200 Transistor RF AMPQ202 FET RF driver AMPQ203 FET APC switchQ204 FET RF final AMP

Q205 Transistor 3.3V5V level converterQ206 FET APC switchQ207 Transistor APC switchQ208 FET APC switchQ209 FET SPDT EXT/INT switchQ210 Transistor RF AMPQ300 Transistor Ripple filterQ301 FET LNA (Low Noise AMP)Q302 FET IF AMPQ303 Transistor 2nd local buffer AMPQ304 Transistor W/N switch

Q450,451 Transistor Auto gain controlQ452 FET MIC mute switchQ453 FET VGS I/O switchQ454 FET TX scrambler switchQ455 FET EXT MIC switchQ456 FET TX scrambler switchQ457 FET EXT MIC switchQ459 FET Beat shift switchQ460 Transistor Noise AMPQ461 FET VGS I/O switchQ600 FET 5T switchQ601 FET 5R switchQ602 FET SB switchQ603 FET 5M switchQ604 FET 5M switchQ605 FET 5V3.3V level converterQ606 FET Switch

D1 Diode Reverse current preventionD102 Variable Frequency control

capacitance diodeD104~112 Variable Frequency control

capacitance diodeD113,114 Diode Feedback filter switch

D115 Variable FM modulationcapacitance diode

D116,117 Diode Feedback filter switchD118 Diode 5C voltage riseD119 Diode Bypass diodeD200 Diode Local switchD201 Zener diode Voltage protection

D202~205 Diode Antenna switchD206,207 Varistor Surge absorptionD301,302 Variable Vari-cap tune

capacitance diodeD304~307 Variable Vari-cap tune

capacitance diodeD308 Diode Local switch

D450,451 Diode DetectionD452 Diode Reverse current preventionD453 Diode Detection

D454,455 Diode Reverse current preventionD600 Diode Reverse current prevention

D601,602 Varistor Surge absorptionD609,611 Diode Surge absorption

Page 25: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

25

COMPONENTS DESCRIPTION

Ref. No. Part name Description

Top Panel unit (X57-7250-XX C/5)

Ref. No. Part name Description

Control unit (X57-7250-XX B/5)

D901 LED TX/RX LEDIC701 IC AF mute switchIC702,703 IC Audio AMP

IC704 IC Voltage regulator (28M)IC705 IC OP AMP (AF Pre-AMP/TX AF AMP)IC706 IC Voltage detector (5.6V)IC707 IC Voltage regulator (33M)IC708 IC Voltage regulator (33A)IC709 IC DC/DC converter (15D)IC710 IC DC/DC converter (36M)IC711 IC Voltage regulator (25D)IC712 IC Voltage regulator (5M)IC713 IC DC/DC converter (15V)IC800 IC DC AMP for LCD voltage

IC801~803 IC Shift registerQ700 FET 5A AVR switchQ701 Transistor 5A AVR switchQ702 Transistor 5A AVR

Q703,704 FET External audio mute switchQ705,706 FET Internal audio mute switch

Q708 FET EXT/INT gain convert switchQ709 Transistor Noise canceler switchQ710 FET Switch (36M DC/DC)Q711 FET Switch (15V DC/DC)Q712 FET DSP power supply timing controlQ713 FET DC/DC converter (36M) control

Q800,801 Transistor switch (backlight)Q802 FET PSW switchQ803 FET Busy LED switchQ804 FET TX LED switch

D700,701 diode Reverse current preventionD702 diode Surge absorptionD703 diode Reverse current preventionD704 diode flywheel (DC/DC)

D705~708 diode Reverse current preventionD800~803 LED Key backlightD804,805 diode Reverse current preventionD806~809 LED Key backlightD810~812 LED LCD backlightD813,814 diode Reverse current prevention

D815 Zener diode AVR for backlight LEDD816~818 diode Reverse current prevention

Page 26: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

2626

PARTS LIST

CAPACITORS

1 = Type ... ceramic, electrolytic, etc.

2 = Shape ... round, square, ect.

3 = Temp. coefficient

4 = Voltage rating

5 = Value

6 = Tolerance

Color*CC45

Capacitor value

010 = 1pF

100 = 10pF

101 = 100pF

102 = 1000pF = 0.001µF

103 = 0.01µF

2 2

Multiplier

2nd number

1st number

0 = 22pF

CC 45 TH 1H J2201 2 3 4 65

Temperature coefficient

Tolerance (More than 10pF)

Voltage rating

Chip capacitors

1

1st Word

Color*

Code D G J K M X Z P No code

LC P R S T U

Black Red Orange Yellow Green Blue Violet

0 -80 -150 -220

+ 40

- 40

+ 80

- 20

+ 100

-0

-330 -470 -750

C(%)

ppm/

0.25 0.5 2 5 10 20 More than 10µF -10 +50

Less than 4.7µF -10 +75

2nd Word HG

Example : CC45TH = -470

J K L

ppm/ 30 60

0.1 0.25 0.5 1 2

120 250 500

60ppm/

Gode C D F GB

(pF)

(Less than 10pF)

1st word2nd word A

0 2.0 2.5 3.15

20 25 31.5

200 250 315

2000 2500 3150

1.0 1.25 1.6

10 12.5 16

100 125 160

1000 1250 1600

1

2

3

B C D E F

4.0

40

400

4000

G

5.0

50

500

5000

H

6.3

63

630

6300

J

8.0

80

800

8000

K

-

35

-

-

V

(EX) C C 7 3 F S L 1 H 0 0 0 JRefer to the table above.

1 = Type

2 = Shape

5 = Voltage rating

4 = Temp. coefficient

3 = Dimension

6 = Value

7 = Tolerance

7654321

(EX) C K 7 3 F F 1 H 0 0 0 Z

7654321

(Chip)(CH,RH,UJ,SL)

(Chip)(B,F)

Chip resistor (Carbon)

(EX) R D 7 3 E B 2 B 0 0 0 J

7654321

RESISTORS

(Chip)(B,F)

Carbon resistor (Normal type)

(EX) R D 1 4 B B 2 C 0 0 0 J

7654321

1 = Type

2 = Shape

5 = Rating wattage

4 = Temp. coefficient

3 = Dimension

6 = Value

7 = Tolerance

Dimension code L W T

Empty

A

B

C

D

E

F

G

H

L

W

T

0.55.0

0.43.2

0.32.0

0.21.25

0.21.6

0.21.25

0.20.8

0.050.5 0.050.5

0.32.5

0.55.6

0.54.5

0.54.5

0.54.5

0.23.0

0.32.0

0.21.6

0.051.0

0.43.2

Less than 2.0

Less than 2.0

Less than 2.0

Less than 1.25

Less than 1.5

Less than 1.25

Less than 1.25

Less than 1.0

Dimension (Chip capacitors)

Dimension (Chip resistor)

Rating wattage

Dimension

Dimension code L W T

E

F

G

H

0.21.6

0.21.25

0.20.8

0.050.5

0.10.5

0.050.35

0.23.2

0.32.0

0.21.6

0.051.0

1.0

1.0

Code

2C

2H2E

Wattage

1/6W

1/2W1/4W

Code

1J

2B2A

Wattage

1/16W

1/8W1/10W

Code

3A

3D

Wattage

1W

2W

Page 27: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

∗ New Parts. indicates safety critical components.Parts without Parts No. are not supplied.Les articles non mentionnes dans le Parts No. ne sont pas fournis.Teile ohne Parts No. werden nicht geliefert.

L: Scandinavia K: USA P: CanadaY: PX (Far East, Hawaii) T: England E: EuropeY: AAFES (Europe) X: Australia M: Other Areas

Parts No. DescriptionAddressNewpartsDestination Destination

TK-5310

Ref. No. Parts No. DescriptionAddressNewparts

TK-5310 (Y50-6060-XX)

Ref. No.

TK-5310PARTS LIST

27

50 2B,2D G53-1631-05 PACKING(LEVER SW O-RING)51 1B,1D G53-1633-04 PACKING(SP)52 1B,1D, G53-1634-14 PACKING(MAIN MIC,NC MIC)

2A,2C

53 2A,2C G53-1637-04 PACKING(CHASSIS-FRONT)54 2B,2D G53-1638-04 PACKING(CHASSIS-TOP)55 3A,3C G53-1640-03 PACKING(BATT)56 3A,3C G53-1649-05 PACKING(BATT- O-RING)57 3A,3C G53-1663-23 PACKING(TERMINAL BLOCK)

59 3F ∗ H52-2174-02 ITEM CARTON CASE60 1C J19-5475-12 HOLDER(LCD) K2,K3,K560 1C J19-5475-12 HOLDER(LCD) K661 2B,2D J19-5477-04 HOLDER(EMG)62 2B,2D ∗ J21-8482-13 MOUNTING HARDWARE(TOP)

63 2B,2D J21-8483-03 MOUNTING HARDWARE(SP)64 3A,3C J21-8484-04 MOUNTING HARDWARE(NC MIC)65 2B,2D ∗ J21-8581-04 MOUNTING HARDWARE(LEVER SW)66 2B,2D J21-8495-04 MOUNTING HARDWARE(LEVER SW PANEL SIDE)67 2E ∗ J29-0730-05 BELT CLIP ACCESSORY

68 2B,2D J39-0646-03 SPACER(VOL)69 2B,2D J39-0647-03 SPACER(16CH)70 2B,2D J82-0096-05 FPC(VOL/CH)71 3A,3C J82-0097-25 FPC(UNIV)72 2B,2D J82-0098-05 FPC(SP/MIC)

73 2A,2C J82-0104-05 FPC(CONTROL-TOP)74 3A,3C J99-0377-14 ADHESIVE SHEET(PTT)75 3A,3C J99-0380-04 ADHESIVE SHEET(ANT PCB)76 2A,2C J99-0381-04 ADHESIVE SHEET(CONTROL-TOP FPC)77 1B,1D J99-0383-14 ADHESIVE SHEET(SP)

78 1C J99-0390-04 ADHESIVE SHEET(LCD FILTER) K2,K3,K578 1C J99-0390-04 ADHESIVE SHEET(LCD FILTER) K680 2B,2D K29-9319-03 KEY TOP(EMG)81 1D K29-9320-03 KEY TOP(4KEY) K2,K582 1C K29-9321-13 KEY TOP(DTMF) K3,K6

83 2B,2D K29-9322-03 KNOB(VOL)84 2B,2D K29-9323-03 KNOB(16CH)85 2B,2D K29-9324-13 KNOB(CONCENTRIC SW)86 2B,2D K29-9325-04 KNOB(LEVER SW)87 1A,1C K29-9327-03 KEY TOP(PTT)

88 1A,1C K29-9328-02 KNOB(PTT)

A 1B,1D,2E N08-0531-14 DRESSED SCREW(CAP) ACCESSORYB 2B,2D N09-2439-25 SPECIAL SCREW(SP)C 3A,3C N09-2440-15 SPECIAL SCREW(CASE)D 3A,3C N09-2441-15 SPECIAL SCREW(COVER ASSY)E 2B,2D N09-2442-15 SPECIAL SCREW(ANT)

F 3A,3C ∗ N09-2443-14 HEXAGON HEAD SCREW(BATT-)H 2B,2D N14-0813-14 CIRCULAR NUT(VOL)I 2B,2D ∗ N14-0814-14 CIRCULAR NUT(CH)J 2B,2D N14-0815-04 CIRCULAR NUT(ANT)K 2B,2D ∗ N14-0817-14 HEXAGON NUT(LEVER SW)

M 2E N30-3008-60 PAN HEAD MACHINE SCREW(BELT CLIP)N 2B,2D N32-2004-48 FLAT HEAD MACHINE SCREW(TOP)P 1A,1C, N83-2005-48 PAN HEAD TAPTITE SCREW(CONT/TXRX)

2A,2C

1 1A A02-3875-01 MAIN CABINET K,K42 1D A02-3877-11 MAIN CABINET(4KEY) K2,K53 1D ∗ A02-3879-11 MAIN CABINET(DTMF) K3,K64 3A,3C ∗ A10-4084-31 CHASSIS5 2B,2D A62-1104-02 PANEL(TOP)

6 3A,3C A82-0057-02 REAR PANEL7 2B,2D B03-3612-04 DRESSING PLATE(16CH)8 1B,1D,2E B09-0682-13 CAP(SP/MIC) ACCESSORY9 2B,2D B11-1821-03 ILLUMINATION GUIDE(TX-BUSY)10 1C B11-1832-04 FILTER(LCD) K2,K3,K5

10 1C B11-1832-04 FILTER(LCD) K611 1C ∗ B38-0891-15 LCD ASSY K2,K3,K511 1C ∗ B38-0891-15 LCD ASSY K612 3A,3C B41-1841-04 CAUTION STICKER(HUMAN BODY PROTECTION)13 1B,1D B43-1171-04 BADGE(FRONT)

14 2B,2D B43-1172-04 BADGE(REAR)15 2E B59-2393-00 SUB-INSTRUCTION MANUAL(QRC/ENGLISH)16 2E ∗ B59-2439-00 SUB-INSTRUCTION MANUAL(QRC/FRENCH)17 2E ∗ B59-2448-00 PAMPHLET(HUMAN BODY PROTECTION)18 2E ∗ B62-1972-00 INSTRUCTION MANUAL(ENGLISH/FRENCH)

20 3A ∗ B72-2418-04 MODEL NAME-PLATE K21 3C ∗ B72-2419-04 MODEL NAME-PLATE K222 3C ∗ B72-2420-04 MODEL NAME-PLATE K323 3A ∗ B72-2421-04 MODEL NAME-PLATE K424 3C ∗ B72-2422-04 MODEL NAME-PLATE K5

25 3C ∗ B72-2423-04 MODEL NAME-PLATE K627 2A,2C E37-0722-05 LEAD WIRE WITH CONNECTOR(UNIV)28 2B,2D E37-1126-15 LEAD WIRE WITH CONNECTOR(ANT)29 2C E37-1128-05 FLAT CABLE(CN613-CN800) K2,K3,K529 2C E37-1128-05 FLAT CABLE(CN613-CN800) K6

30 3A,3C E58-0510-05 RECTANGULAR RECEPTACLE(UNIV)31 3A,3C E72-0420-33 TERMINAL BLOCK(BATT+)32 3A,3C F07-1887-12 COVER ASSY33 2A,2C F10-2499-12 SHIELDING PLATE(TX-RX PCB)34 3A,3C G10-1327-04 FIBROUS SHEET(AIR)

35 1B,1D G10-1338-04 FIBROUS SHEET(SP)36 3A,3C ∗ G10-1366-04 FIBROUS SHEET37 1C G11-4302-04 SHEET(LCD) K2,K3,K537 1C G11-4302-04 SHEET(LCD) K638 3A,3C G11-4303-14 SHEET(PTT)

39 1B,1D,2E G11-4340-04 RUBBER SHEET(CAP) ACCESSORY40 - G11-4346-08 SHEET(UNIV)41 1A,1C G13-2036-04 CUSHION(MIC)42 3A,2C,3C G13-2046-04 CUSHION(UNIV)43 1A,2C, G13-2070-04 CUSHION(CORD ASSY)

3A,3C

44 2A,2C G13-2071-04 CONDUCTIVE CUSHION(CHASSIS/PCB)45 2B,2D G13-2079-04 CUSHION(VOL)46 1C G13-2087-04 CUSHION(LCD) K2,K3,K546 1C G13-2087-04 CUSHION(LCD) K647 2B,2D G53-1628-04 PACKING(VOL TORQ-UP)

48 2B,2D G53-1629-05 PACKING(VOL,CH O-RING)49 2B,2D G53-1630-05 PACKING(ANT O-RING)

Page 28: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

28

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

Q 2B,2D N83-2006-43 PAN HEAD TAPTITE SCREW(TOP)

90 3B,3D R31-0654-05 VARIABLE RESISTOR(VOL)91 3B,3D S60-0431-05 ROTARY SWITCH(CH)92 1C S79-0454-05 KEYBOARD ASSY(4KEY,DTMF) K2,K3,K592 1C S79-0454-05 KEYBOARD ASSY(4KEY,DTMF) K693 1B,1D T07-0755-15 SPEAKER

94 2A,2B, T91-0575-05 MIC ELEMENTT(MAIN MIC,NC MIC)2C,2D

95 1C W09-0971-05 LITHIUM CELL96 3A,3C X41-3690-10 SWITCH UNIT(FPC(PTT))97 1A,2C X42-3270-10 CORD ASSY(FPC(50PIN))

D800-803 B30-2171-05 LED K3,K6D800,801 B30-2171-05 LED K2,K5D806-809 B30-2171-05 LED K3,K6D810-812 B30-2261-05 LED K2,K3,K5D810-812 B30-2261-05 LED K6

D901 B30-2019-05 LED(RE/GR)

C1 CK73HB1A104K CHIP C 0.10UF KC2 CK73HB1C103K CHIP C 0.010UF KC3 CK73HB1A104K CHIP C 0.10UF KC5 CK73HB1A104K CHIP C 0.10UF KC6 -8 CK73HB1H471K CHIP C 470PF K

C10 ,11 CK73HB1A104K CHIP C 0.10UF KC12 CK73HB1H471K CHIP C 470PF KC13 CC73HCH1H470J CHIP C 47PF JC14 CK73HB1C103K CHIP C 0.010UF KC15 CK73HB1A104K CHIP C 0.10UF K

C17 CK73HB1A104K CHIP C 0.10UF KC18 ,19 CK73HB1H471K CHIP C 470PF KC20 CK73HB1A104K CHIP C 0.10UF KC22 CK73HB1A104K CHIP C 0.10UF KC23 CK73HB1C103K CHIP C 0.010UF K

C24 CK73GB0J475K CHIP C 4.7UF KC25 -27 CK73HB1C103K CHIP C 0.010UF KC28 CK73GB0J475K CHIP C 4.7UF KC29 ,30 CK73HB1C103K CHIP C 0.010UF KC32 -35 CK73HB1C103K CHIP C 0.010UF K

C38 CK73HB1C103K CHIP C 0.010UF KC101 CK73HB1A104K CHIP C 0.10UF KC102,103 CC73HCH1H470J CHIP C 47PF JC105 CC73HCH1H470J CHIP C 47PF JC106,107 CK73HB1H471K CHIP C 470PF K

C108 CK73HB1A104K CHIP C 0.10UF KC109 CK73GB1E105K CHIP C 1.0UF KC110 CK73HB1H471K CHIP C 470PF KC111 CK73GB1E105K CHIP C 1.0UF KC114,115 CK73HB1A104K CHIP C 0.10UF K

C116,117 CK73HB1C103K CHIP C 0.010UF KC118 CK73HB1H471K CHIP C 470PF KC122 CC73HCH1H470J CHIP C 47PF JC125 CK73GB1C104K CHIP C 0.10UF KC126 C93-0787-05 CERAMIC 0.1UF 50WV

C127 CK73HB1H471K CHIP C 470PF KC128 CC73HCH1H470J CHIP C 47PF JC129 CK73HB1C103K CHIP C 0.010UF KC130 CC73HCH1H470J CHIP C 47PF J

C131 CK73HB1C103K CHIP C 0.010UF K

C132 CK73HB1H471K CHIP C 470PF KC135,136 CK73HB1C103K CHIP C 0.010UF KC137,138 CC73HCH1H101J CHIP C 100PF JC139 CK73HB1C103K CHIP C 0.010UF KC140 C92-0863-05 CHIP TNTL 0.047UF 35WV

C141 CK73HB1H471K CHIP C 470PF KC142 ∗ CS77AA1VR47M CHIP TNTL 0.47UF 35WVC143 CK73HB1H471K CHIP C 470PF KC144 CS77CP0J100M CHIP TNTL 10UF 6.3WVC145 CK73HB1H471K CHIP C 470PF K

C147 CK73GB0J475K CHIP C 4.7UF KC148 CK73HB1H471K CHIP C 470PF KC149 CC73HCH1H150J CHIP C 15PF J K,K2,K3C149 CC73HCH1H390J CHIP C 39PF J K4,K5,K6C150 CC73HCH1H0R5B CHIP C 0.5PF B K,K2,K3

C150 CC73HCH1H010B CHIP C 1.0PF B K4,K5,K6C151 CC73HCH1H220J CHIP C 22PF J K,K2,K3C151 CC73HCH1H270J CHIP C 27PF J K4,K5,K6C152 CC73HCH1H2R5B CHIP C 2.5PF BC153 CK73HB1H471K CHIP C 470PF K

C154 CC73HCH1H0R5B CHIP C 0.5PF BC155 CK73HB1H471K CHIP C 470PF KC156 CC73GCH1H050B CHIP C 5.0PF B K,K2,K3C156 CC73GCH1H060B CHIP C 6.0PF B K4,K5,K6C157 CC73GCH1H020B CHIP C 2.0PF B K,K2,K3

C157 CC73GCH1H050B CHIP C 5.0PF B K4,K5,K6C158,159 CC73HCH1H470J CHIP C 47PF J K4,K5,K6C159 CC73HCH1H470J CHIP C 47PF J K,K2,K3C160,161 CC73GCH1H050B CHIP C 5.0PF BC162 CC73HCH1H100B CHIP C 10PF B K4,K5,K6

C163 CC73HCH1H080B CHIP C 8.0PF B K,K2,K3C163 CC73HCH1H120J CHIP C 12PF J K4,K5,K6C164 CC73GCH1H050B CHIP C 5.0PF B K4,K5,K6C164 CC73GCH1H060B CHIP C 6.0PF B K,K2,K3C165 CC73GCH1H040B CHIP C 4.0PF B

C166-168 CK73HB1H471K CHIP C 470PF KC169,170 CC73HCH1H020B CHIP C 2.0PF B K4,K5,K6C170 CC73HCH1H020B CHIP C 2.0PF B K,K2,K3C171,172 CC73HCH1H0R5B CHIP C 0.5PF BC173 CC73HCH1H090B CHIP C 9.0PF B K4,K5,K6

C174 CC73HCH1H030B CHIP C 3.0PF B K,K2,K3C174 CC73HCH1H060B CHIP C 6.0PF B K4,K5,K6C175 CC73HCH1H040B CHIP C 4.0PF B K4,K5,K6C176 CC73HCH1H020B CHIP C 2.0PF B K,K2,K3C176 CC73HCH1H2R5B CHIP C 2.5PF B K4,K5,K6

C177 CC73HCH1H101J CHIP C 100PF J K4,K5,K6C178,179 CK73HB1H471K CHIP C 470PF KC180 CC73HCH1H040B CHIP C 4.0PF B K,K2,K3C180 CC73HCH1H100B CHIP C 10PF B K4,K5,K6C182-185 CK73HB1H471K CHIP C 470PF K

C186 CK73HB0J105K CHIP C 1.0UF KC187 CC73HCH1H050B CHIP C 5.0PF B K,K2,K3C187 CC73HCH1H150J CHIP C 15PF J K4,K5,K6C188 CK73GB1H471K CHIP C 470PF KC189,190 CC73HCH1H470J CHIP C 47PF J K4,K5,K6

C191 CK73HB1H471K CHIP C 470PF KC200 CK73HB1C103K CHIP C 0.010UF KC201 CK73HB1H471K CHIP C 470PF K K4,K5,K6

TK-5310

TX-RX UNIT (X57-7250-XX)-10 :K -11 :K2 -12 :K3 -13 :K4 -14 :K5 -15 :K6

Page 29: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

29

C201,202 CK73HB1H471K CHIP C 470PF K K,K2,K3C202 CC73HCH1H220J CHIP C 22PF J K4,K5,K6

C203,204 CC73HCH1H070B CHIP C 7.0PF B K4,K5,K6C205,206 CK73HB1H471K CHIP C 470PF KC207 CC73HCH1H070B CHIP C 7.0PF BC209,210 CK73HB1H471K CHIP C 470PF KC215,216 CK73HB1H471K CHIP C 470PF K

C218 CC73HCH1H050B CHIP C 5.0PF B K,K2,K3C218 CC73HCH1H060B CHIP C 6.0PF B K4,K5,K6C219 CK73HB1C103K CHIP C 0.010UF KC220 CK73HB1H471K CHIP C 470PF KC221 CC73HCH1H150J CHIP C 15PF J

C223 CK73HB1H471K CHIP C 470PF KC224 CC73GCH1H270J CHIP C 27PF J K,K2,K3C224 CC73GCH1H390J CHIP C 39PF J K4,K5,K6C225 CK73HB1H471K CHIP C 470PF K K,K2,K3C226 CK73GB1H471K CHIP C 470PF K

C227,228 CK73HB1H471K CHIP C 470PF K K4,K5,K6C228 CK73HB1H471K CHIP C 470PF K K,K2,K3C229 CK73HB1C103K CHIP C 0.010UF KC230 CK73HB1H471K CHIP C 470PF KC231 CC73HCH1H101J CHIP C 100PF J

C232 CC73GCH1H220J CHIP C 22PF J K,K2,K3C234,235 CK73HB1H471K CHIP C 470PF KC237 CK73HB1C103K CHIP C 0.010UF KC238 CK73GB1E105K CHIP C 1.0UF KC239-242 CK73HB1H471K CHIP C 470PF K

C243 ∗ C93-0951-05 CERAMIC 47PF 50WV K,K2,K3C243 ∗ C93-0955-05 CERAMIC 68PF 50WV K4,K5,K6C244,245 CK73HB1H471K CHIP C 470PF K K4,K5,K6C245 CK73HB1H471K CHIP C 470PF K K,K2,K3C246 CK73HB1C103K CHIP C 0.010UF K

C247 CK73HB1H471K CHIP C 470PF KC249 CK73GB1C104K CHIP C 0.10UF KC250 ∗ C93-0945-05 CERAMIC 27PF 50WV K,K2,K3C252 CK73GB1H471K CHIP C 470PF KC253 CK73GB0J475K CHIP C 4.7UF K

C254 CK73HB1H471K CHIP C 470PF KC255 ∗ C93-0941-05 CERAMIC 18PF 50WV K4,K5,K6C256 ∗ C93-0878-05 CERAMIC 2.0PF 100WV K,K2,K3C256 ∗ C93-0989-05 CERAMIC 8.2PF 50WV K4,K5,K6C257 CC73GCH1H101J CHIP C 100PF J K,K2,K3

C257,258 CK73GB1H471K CHIP C 470PF K K4,K5,K6C258 CK73GB1H471K CHIP C 470PF K K,K2,K3C259 CK73HB1C103K CHIP C 0.010UF KC260 CC73GCH1H070B CHIP C 7.0PF B K4,K5,K6C260 CC73GCH1H090D CHIP C 9.0PF D K,K2,K3

C261 CC73GCH1H020B CHIP C 2.0PF B K4,K5,K6C261 CC73GCH1H040B CHIP C 4.0PF B K,K2,K3C262 CK73HB1H471K CHIP C 470PF KC263 CC73HCH1H060B CHIP C 6.0PF B K,K2,K3C263 CC73HCH1H100B CHIP C 10PF B K4,K5,K6

C264 CC73HCH1H010B CHIP C 1.0PF BC265 CC73HCH1H070B CHIP C 7.0PF B K,K2,K3C265 CC73HCH1H150J CHIP C 15PF J K4,K5,K6C266 CC73HCH1H040B CHIP C 4.0PF B K4,K5,K6C267 CC73HCH1H010B CHIP C 1.0PF B

C268 CC73HCH1H0R5B CHIP C 0.5PF B K,K2,K3C268 CC73HCH1H060B CHIP C 6.0PF B K4,K5,K6

C270,271 CK73GB1H471K CHIP C 470PF KC273 CK73HB1H471K CHIP C 470PF KC277 CK73HB1H471K CHIP C 470PF K

C278 CC73GCH1H070B CHIP C 7.0PF B K4,K5,K6C278 CC73GCH1H090D CHIP C 9.0PF D K,K2,K3C280 CK73HB1H471K CHIP C 470PF KC281 CC73GCH1H070B CHIP C 7.0PF B K4,K5,K6C281-283 CC73GCH1H090D CHIP C 9.0PF D K,K2,K3

C282,283 CC73GCH1H150J CHIP C 15PF J K4,K5,K6C284,285 CK73HB1H471K CHIP C 470PF KC288 CC73HCH1H030B CHIP C 3.0PF B K,K2,K3C288 CC73HCH1H060B CHIP C 6.0PF B K4,K5,K6C289 CC73GCH1H050B CHIP C 5.0PF B K4,K5,K6

C289 CC73GCH1H2R5B CHIP C 2.5PF B K,K2,K3C290 CC73HCH1H030B CHIP C 3.0PF B K,K2,K3C290 CC73HCH1H060B CHIP C 6.0PF B K4,K5,K6C291 CC73HCH1H040B CHIP C 4.0PF BC292 CC73GCH1H050B CHIP C 5.0PF B K4,K5,K6

C292 CC73GCH1H2R5B CHIP C 2.5PF B K,K2,K3C293 CC73HCH1H040B CHIP C 4.0PF BC295 ∗ C93-0937-05 CERAMIC 12PF 50WV K,K2,K3C295 ∗ C93-0941-05 CERAMIC 18PF 50WV K4,K5,K6C296 ∗ C93-0989-05 CERAMIC 8.2PF 50WV K,K2,K3

C297 ∗ C93-0947-05 CERAMIC 33PF 50WV K4,K5,K6C299 CK73HB1H471K CHIP C 470PF KC300 CK73GB1C104K CHIP C 0.10UF KC302 CK73GB1E105K CHIP C 1.0UF KC303 CK73GB1C104K CHIP C 0.10UF K

C306,307 CC73GCH1H120G CHIP C 12PF G K,K2,K3C306,307 CC73GCH1H180J CHIP C 18PF J K4,K5,K6C308 CK73HB1H471K CHIP C 470PF KC309 CC73HCH1H150J CHIP C 15PF J K,K2,K3C309 CC73HCH1H470J CHIP C 47PF J K4,K5,K6

C311 CC73GCH1H010B CHIP C 1.0PF B K,K2,K3C311 CC73GCH1H1R5B CHIP C 1.5PF B K4,K5,K6C312 CC73HCH1H040B CHIP C 4.0PF BC313 CK73HB1H471K CHIP C 470PF KC315 CC73GCH1H180J CHIP C 18PF J K4,K5,K6

C315 CC73GCH1H390J CHIP C 39PF J K,K2,K3C316 CC73HCH1H030B CHIP C 3.0PF B K,K2,K3C316 CC73HCH1H040B CHIP C 4.0PF B K4,K5,K6C317 CC73HCH1H150J CHIP C 15PF J K,K2,K3C317 CC73HCH1H470J CHIP C 47PF J K4,K5,K6

C318 CK73GB1H471K CHIP C 470PF KC321-325 CK73HB1H471K CHIP C 470PF KC327 CK73HB0J105K CHIP C 1.0UF KC329,330 CK73HB1H471K CHIP C 470PF KC332 CC73HCH1H220J CHIP C 22PF J K,K2,K3

C332 CC73HCH1H270J CHIP C 27PF J K4,K5,K6C333,334 CK73HB1H471K CHIP C 470PF KC335 CC73HCH1H050B CHIP C 5.0PF B K4,K5,K6C335 CC73HCH1H090B CHIP C 9.0PF B K,K2,K3C336 CC73HCH1H070B CHIP C 7.0PF B K,K2,K3

C336 CC73HCH1H120J CHIP C 12PF J K4,K5,K6C337 CC73HCH1H220J CHIP C 22PF J K,K2,K3C337 CC73HCH1H270J CHIP C 27PF J K4,K5,K6C338 CK73HB1H471K CHIP C 470PF KC339 CC73HCH1H030B CHIP C 3.0PF B K,K2,K3

C339 CC73HCH1H120J CHIP C 12PF J K4,K5,K6

Page 30: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

30

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

C340 CK73HB1H471K CHIP C 470PF KC341 CC73HCH1H070B CHIP C 7.0PF B K,K2,K3C341 CC73HCH1H150J CHIP C 15PF J K4,K5,K6C342 CC73HCH1H220J CHIP C 22PF J K,K2,K3

C342 CC73HCH1H270J CHIP C 27PF J K4,K5,K6C344 CC73HCH1H040B CHIP C 4.0PF B K,K2,K3C344 CC73HCH1H070B CHIP C 7.0PF B K4,K5,K6C345 CK73HB1H471K CHIP C 470PF KC346 CC73HCH1H070B CHIP C 7.0PF B K,K2,K3

C346 CC73HCH1H080B CHIP C 8.0PF B K4,K5,K6C347 CC73HCH1H220J CHIP C 22PF J K,K2,K3C347 CC73HCH1H270J CHIP C 27PF J K4,K5,K6C348 CC73HCH1H050B CHIP C 5.0PF BC349 CC73HCH1H020B CHIP C 2.0PF B

C350 CK73HB1H471K CHIP C 470PF KC351 CC73HCH1H100B CHIP C 10PF B K4,K5,K6C351,352 CC73HCH1H100B CHIP C 10PF B K,K2,K3C352 CC73HCH1H070B CHIP C 7.0PF B K4,K5,K6C354 CK73HB1H471K CHIP C 470PF K

C355 CC73HCH1H0R5B CHIP C 0.5PF BC356 CC73HCH1H060B CHIP C 6.0PF BC357,358 CK73HB1H471K CHIP C 470PF K K4,K5,K6C358 CK73HB1H471K CHIP C 470PF K K,K2,K3C360,361 CK73HB1H471K CHIP C 470PF K

C362 CC73GCH1H150J CHIP C 15PF J K4,K5,K6C362 CK73GB1H471K CHIP C 470PF K K,K2,K3C363 CK73HB1H471K CHIP C 470PF KC365,366 CK73HB1H471K CHIP C 470PF KC367,368 CK73HB1A104K CHIP C 0.10UF K

C370 CK73HB1C103K CHIP C 0.010UF KC372 CC73GCH1H150J CHIP C 15PF JC374 CC73HCH1H270J CHIP C 27PF JC378 CC73HCH1H120J CHIP C 12PF JC379-382 CK73HB1C103K CHIP C 0.010UF K

C383 CC73HCH1H220J CHIP C 22PF JC385 CC73HCH1H470J CHIP C 47PF JC386 CC73HCH1H080B CHIP C 8.0PF BC387 CK73HB1H471K CHIP C 470PF KC388 CK73HB1C103K CHIP C 0.010UF K

C389 CC73HCH1H470J CHIP C 47PF JC390 CC73HCH1H220J CHIP C 22PF JC391 CC73HCH1H820J CHIP C 82PF JC392 CC73HCH1H470J CHIP C 47PF JC393-396 CK73HB1A104K CHIP C 0.10UF K

C397 CC73HCH1H680J CHIP C 68PF JC398 CK73HB1A104K CHIP C 0.10UF KC399 CK73HB1H102K CHIP C 1000PF KC400-404 CK73HB1A104K CHIP C 0.10UF KC405,406 CK73HB1C103K CHIP C 0.010UF K

C407 CK73FB0J106K CHIP C 10UF KC408,409 CK73HB1A104K CHIP C 0.10UF KC410 CC73HCH1H390J CHIP C 39PF JC411,412 CC73HCH1H151J CHIP C 150PF JC413 CK73HB1C223K CHIP C 0.022UF K

C414 CC73HCH1H101J CHIP C 100PF JC415 CK73HB1H102K CHIP C 1000PF KC416 CK73HB1A104K CHIP C 0.10UF KC418,419 CK73HB1A104K CHIP C 0.10UF KC420 CK73GB0J225K CHIP C 2.2UF K

C421,422 CK73HB1A104K CHIP C 0.10UF KC423 CC73GCH1H060B CHIP C 6.0PF BC450 CK73HB0J105K CHIP C 1.0UF KC451,452 CC73HCH1H101J CHIP C 100PF JC453 CK73HB1A104K CHIP C 0.10UF K

C454,455 CK73GB0J475K CHIP C 4.7UF KC456 CK73GB0J225K CHIP C 2.2UF KC457,458 CK73HB0J105K CHIP C 1.0UF KC459 CK73GB0J225K CHIP C 2.2UF KC460,461 CK73HB1A104K CHIP C 0.10UF K

C462 CK73HB1H471K CHIP C 470PF KC463 CK73HB0J105K CHIP C 1.0UF KC464,465 CK73HB1A104K CHIP C 0.10UF KC466,467 CK73HB0J105K CHIP C 1.0UF KC468,469 CK73HB1A104K CHIP C 0.10UF K

C470,471 CC73HCH1H151J CHIP C 150PF JC472 CK73HB1A104K CHIP C 0.10UF KC473 CK73HB1H471K CHIP C 470PF KC474 CK73HB1A104K CHIP C 0.10UF KC475 CK73HB1C103K CHIP C 0.010UF K

C476 CK73HB0J105K CHIP C 1.0UF KC477 CK73HB1A104K CHIP C 0.10UF KC478,479 CK73GB0J475K CHIP C 4.7UF KC480 CK73HB1C103K CHIP C 0.010UF KC481,482 CK73HB1A104K CHIP C 0.10UF K

C483 CK73FB0J106K CHIP C 10UF KC484 CK73HB1A104K CHIP C 0.10UF KC485 CK73HB0J105K CHIP C 1.0UF KC486 CK73HB1H102K CHIP C 1000PF KC487 CK73HB1A104K CHIP C 0.10UF K

C488 CK73HB0J224K CHIP C 0.22UF KC493 CK73HB0J224K CHIP C 0.22UF KC496 CK73HB1A104K CHIP C 0.10UF KC497 CK73FB0J106K CHIP C 10UF KC498 CK73HB1H122K CHIP C 1200PF K

C499 CK73HB1A104K CHIP C 0.10UF KC501 CC73HCH1H101J CHIP C 100PF JC502 CK73HB1A104K CHIP C 0.10UF KC504 CK73GB1A105K CHIP C 1.0UF KC505 CK73FB0J106K CHIP C 10UF K

C506 CK73HB1C103K CHIP C 0.010UF KC507 CK73HB1A104K CHIP C 0.10UF KC508 CK73HB1C103K CHIP C 0.010UF KC509 CK73GB0J475K CHIP C 4.7UF KC510 CK73HB0J105K CHIP C 1.0UF K

C511 CK73HB1C103K CHIP C 0.010UF KC512 CC73HCH1H151J CHIP C 150PF JC513 CK73HB1A104K CHIP C 0.10UF KC515 CK73GB0J475K CHIP C 4.7UF KC517 CK73HB1H272K CHIP C 2700PF K

C519 CC73HCH1H101J CHIP C 100PF JC520 CK73HB1C103K CHIP C 0.010UF KC522,523 CK73HB1C103K CHIP C 0.010UF KC524 CK73HB1A104K CHIP C 0.10UF KC526 CC73HCH1H101J CHIP C 100PF J

C527,528 CK73HB1A104K CHIP C 0.10UF KC529 CK73HB1C103K CHIP C 0.010UF KC530-532 CK73HB1A104K CHIP C 0.10UF KC533 CK73FB0J106K CHIP C 10UF KC534,535 CK73HB1A104K CHIP C 0.10UF K

Page 31: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

31

C536 CK73HB0J105K CHIP C 1.0UF KC537 CK73HB1A104K CHIP C 0.10UF KC538 CK73HB0J105K CHIP C 1.0UF KC539 CC73HCH1H101J CHIP C 100PF JC540 CK73HB1A104K CHIP C 0.10UF K

C541 CK73FB0J106K CHIP C 10UF KC542 CK73HB1A104K CHIP C 0.10UF KC543 CC73HCH1H101J CHIP C 100PF JC602-605 CK73HB1H471K CHIP C 470PF KC606 CK73GB1C104K CHIP C 0.10UF K

C607 CK73HB1H471K CHIP C 470PF KC608 CK73FB0J106K CHIP C 10UF KC609 CK73GB1E105K CHIP C 1.0UF KC610 CK73GB1C104K CHIP C 0.10UF KC612,613 CK73HB1H471K CHIP C 470PF K

C614-617 CK73GB1E105K CHIP C 1.0UF KC619-624 CC73HCH1H101J CHIP C 100PF JC625 CK73HB1H332K CHIP C 3300PF KC626 CK73HB1H471K CHIP C 470PF KC627 CC73HCH1H101J CHIP C 100PF J

C629,630 CC73HCH1H101J CHIP C 100PF JC631 CK73HB1H471K CHIP C 470PF KC632 CC73HCH1H101J CHIP C 100PF JC633,634 CK73HB1H471K CHIP C 470PF KC635 CC73HCH1H101J CHIP C 100PF J

C636-638 CK73HB1H471K CHIP C 470PF KC639 CK73HB1A104K CHIP C 0.10UF KC640 CK73HB1H471K CHIP C 470PF KC641-644 CK73HB1A104K CHIP C 0.10UF KC645 CK73HB1C103K CHIP C 0.010UF K

C646 CK73HB1A104K CHIP C 0.10UF KC648-650 CK73HB1A104K CHIP C 0.10UF KC651 CC73HCH1H101J CHIP C 100PF JC653,654 CC73HCH1H101J CHIP C 100PF JC657 CC73HCH1H101J CHIP C 100PF J

C660,661 CC73HCH1H101J CHIP C 100PF JC664,665 CC73HCH1H101J CHIP C 100PF JC668,669 CC73HCH1H101J CHIP C 100PF JC674 CK73HB1H471K CHIP C 470PF KC675 CK73HB1H102K CHIP C 1000PF K

C677 CK73HB1A104K CHIP C 0.10UF KC700 CK73HB1A104K CHIP C 0.10UF KC701 CK73HB1H471K CHIP C 470PF KC702 CK73FB0J106K CHIP C 10UF KC703 CK73HB1H471K CHIP C 470PF K

C704 CK73FB0J106K CHIP C 10UF KC707 CK73HB1A104K CHIP C 0.10UF KC708,709 CK73GB1A105K CHIP C 1.0UF KC712,713 CK73GB0J225K CHIP C 2.2UF KC716,717 CK73HB1A104K CHIP C 0.10UF K

C718,719 CK73HB1H471K CHIP C 470PF KC724 CK73HB0J105K CHIP C 1.0UF KC725 CK73GB1E105K CHIP C 1.0UF KC726 CK73HB1A104K CHIP C 0.10UF KC727 CK73GB0J225K CHIP C 2.2UF K

C728 CC73HCH1H101J CHIP C 100PF JC729 CK73HB1A104K CHIP C 0.10UF KC730 CK73GB1C474K CHIP C 0.47UF KC731 CK73HB1A104K CHIP C 0.10UF KC732 CK73GB1E223K CHIP C 0.022UF K

C734 CK73HB1H471K CHIP C 470PF KC736,737 CK73GB1C474K CHIP C 0.47UF KC738-741 CK73HB1H471K CHIP C 470PF KC742,743 ∗ CK73EB1E475K CHIP C 4.7UF KC744 CK73HB1C103K CHIP C 0.010UF K

C745,746 ∗ CK73EB1E475K CHIP C 4.7UF KC747 CK73GB1C104K CHIP C 0.10UF KC748 CK73GB1E105K CHIP C 1.0UF KC749,750 CK73GB1C104K CHIP C 0.10UF KC751 CK73FB0J475K CHIP C 4.7UF K

C752,753 CK73GB1E105K CHIP C 1.0UF KC754 CK73HB1C103K CHIP C 0.010UF KC755 ∗ CK73EB1E475K CHIP C 4.7UF KC757 CK73HB1C103K CHIP C 0.010UF KC759 CK73HB1A104K CHIP C 0.10UF K

C760-762 CK73HB1H471K CHIP C 470PF KC763 CK73HB1A104K CHIP C 0.10UF KC764 CC73HCH1H820J CHIP C 82PF JC765 CK73GB1E105K CHIP C 1.0UF KC766 CK73FB0J475K CHIP C 4.7UF K

C767 CC73HCH1E181J CHIP C 180PF JC768 CK73HB1H471K CHIP C 470PF KC769 CK73GB1E105K CHIP C 1.0UF KC770 CK73HB1H471K CHIP C 470PF KC771 CC73HCH1H220J CHIP C 22PF J

C772 CK73HB1H471K CHIP C 470PF KC773,774 CK73GB1E105K CHIP C 1.0UF KC775 CK73HB1A104K CHIP C 0.10UF KC776 C92-0822-05 CHIP TNTL 33UF 10WVC777-779 CK73GB1E105K CHIP C 1.0UF K

C783-785 CK73HB1H471K CHIP C 470PF KC788 CK73FB0J106K CHIP C 10UF KC790 CK73HB1H471K CHIP C 470PF KC795 CK73GB1E105K CHIP C 1.0UF KC800-803 CK73GB1C474K CHIP C 0.47UF K K2,K3,K5

C800-803 CK73GB1C474K CHIP C 0.47UF K K6C805 CK73HB1C103K CHIP C 0.010UF K K2,K3,K5C805 CK73HB1C103K CHIP C 0.010UF K K6C807 CK73HB1H471K CHIP C 470PF K K2,K3,K5C807 CK73HB1H471K CHIP C 470PF K K6

C808 CK73HB1C103K CHIP C 0.010UF K K2,K3,K5C808 CK73HB1C103K CHIP C 0.010UF K K6C809-812 CK73GB1E105K CHIP C 1.0UF K K2,K3,K5C809-812 CK73GB1E105K CHIP C 1.0UF K K6C814 CK73HB1H471K CHIP C 470PF K K2,K3,K5

C814 CK73HB1H471K CHIP C 470PF K K6C825 CK73HB1H471K CHIP C 470PF K K2,K3,K5C825 CK73HB1H471K CHIP C 470PF K K6C826 CK73HB1C103K CHIP C 0.010UF KC827 CC73HCH1H101J CHIP C 100PF J K2,K3,K5

C827 CC73HCH1H101J CHIP C 100PF J K6C828 CK73HB1A104K CHIP C 0.10UF K K2,K3,K5C828 CK73HB1A104K CHIP C 0.10UF K K6C829 CK73HB1C103K CHIP C 0.010UF KC830-838 CK73HB1E472K CHIP C 4700PF K

C840 CK73HB1C103K CHIP C 0.010UF KC841 CK73HB1E472K CHIP C 4700PF KC842 CK73GB1E223K CHIP C 0.022UF K K2,K3,K5C842 CK73GB1E223K CHIP C 0.022UF K K6

Page 32: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

32

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

CN204,205 E04-0403-05 PIN SOCKETCN301 ∗ E23-0762-05 TERMINALCN601 ∗ E40-6586-05 SOCKET FOR PIN ASSYCN606 E40-6453-05 FLAT CABLE CONNECTORCN609 E40-6357-05 PIN ASSY

CN612 E40-6422-05 SOCKET FOR PIN ASSYCN613 E41-1634-05 FLAT CABLE CONNECTOR K2,K3,K5CN613 E41-1634-05 FLAT CABLE CONNECTOR K6CN700 E40-6421-05 PIN ASSYCN713 ∗ E40-6467-05 FLAT CABLE CONNECTOR

CN800 E41-1634-05 FLAT CABLE CONNECTOR K2,K3,K5CN800 E41-1634-05 FLAT CABLE CONNECTOR K6CN802 E40-6337-05 FLAT CABLE CONNECTOR K2,K3,K5CN802 E40-6337-05 FLAT CABLE CONNECTOR K6CN803 E40-6388-05 FLAT CABLE CONNECTOR

CN804 E40-5664-05 FLAT CABLE CONNECTORCN902 E40-6391-05 FLAT CABLE CONNECTORCN903 ∗ E40-6464-05 FLAT CABLE CONNECTORCN923 E40-6358-05 SOCKET FOR PIN ASSYCN941 E04-0403-05 PIN SOCKET

F600 F53-0372-05 FUSE(3.15A)F601 F53-0360-05 FUSE(0.25A)

CN702 J19-5386-05 HOLDER

CD300 L79-1850-05 TUNING COIL

CF300 L72-1017-05 CERAMIC FILTERCF301 L72-1009-05 CERAMIC FILTERCF302 L72-1021-05 CERAMIC FILTERCF303 L72-1017-05 CERAMIC FILTER

L1 L92-0446-05 BEADS COREL2 -8 L92-0163-05 BEADS COREL9 L92-0446-05 BEADS COREL10 L92-0163-05 BEADS COREL11 L92-0446-05 BEADS CORE

L12 ,13 L92-0162-05 BEADS COREL100 L92-0446-05 BEADS COREL102,103 L40-1001-86 SMALL FIXED INDUCTOR(10UH)L104-106 L40-2285-92 SMALL FIXED INDUCTOR(220NH)L107 L92-0446-05 BEADS CORE

L108,109 L40-2285-92 SMALL FIXED INDUCTOR(220NH)L111-113 L40-2285-92 SMALL FIXED INDUCTOR(220NH)L114 L33-0744-05 SMALL FIXED INDUCTOR K4,K5,K6L114,115 L33-0744-05 SMALL FIXED INDUCTOR K,K2,K3L115 L33-0745-05 SMALL FIXED INDUCTOR K4,K5,K6

L116,117 L40-2285-92 SMALL FIXED INDUCTOR(220NH)L118 L40-3368-71 SMALL FIXED INDUCTOR(3.3NH) K4,K5,K6L119 L40-1868-71 SMALL FIXED INDUCTOR(1.8NH) K4,K5,K6L119 L40-2768-71 SMALL FIXED INDUCTOR(2.7NH) K,K2,K3L120,121 L40-2285-92 SMALL FIXED INDUCTOR(220NH)

L122 L92-0446-05 BEADS CORE K4,K5,K6L123 L40-2275-71 SMALL FIXED INDUCTOR(22NH) K4,K5,K6L124 L40-1875-71 SMALL FIXED INDUCTOR(18NH)L125 L40-1575-71 SMALL FIXED INDUCTOR(15NH) K4,K5,K6L125 L40-2275-71 SMALL FIXED INDUCTOR(22NH) K,K2,K3

L126,127 L40-1075-71 SMALL FIXED INDUCTOR(10NH) K4,K5,K6L127 L40-1075-71 SMALL FIXED INDUCTOR(10NH) K,K2,K3L128 L40-2275-71 SMALL FIXED INDUCTOR(22NH) K,K2,K3L128 L40-2775-71 SMALL FIXED INDUCTOR(27NH) K4,K5,K6L200 ∗ L41-2275-45 SMALL FIXED INDUCTOR(22NH) K,K2,K3

L200,201 ∗ L41-1875-45 SMALL FIXED INDUCTOR(18NH) K4,K5,K6L201 L41-1575-45 SMALL FIXED INDUCTOR(15NH) K,K2,K3L203 L41-1575-45 SMALL FIXED INDUCTOR(15NH) K,K2,K3L203 ∗ L41-1875-45 SMALL FIXED INDUCTOR(18NH) K4,K5,K6L204 L92-0140-05 CHIP FERRITE

L206 ∗ L41-6865-45 SMALL FIXED INDUCTOR(6.8NH) K,K2,K3L208 L92-0149-05 CHIP FERRITEL209 ∗ L41-1875-45 SMALL FIXED INDUCTOR(18NH) K,K2,K3L209 ∗ L41-3975-45 SMALL FIXED INDUCTOR(39NH) K4,K5,K6L210 L41-1575-45 SMALL FIXED INDUCTOR(15NH) K,K2,K3

L211 L34-4566-05 AIR-CORE COILL212 L92-0149-05 CHIP FERRITEL213 L41-8285-14 SMALL FIXED INDUCTOR(820NH)L214-216 L34-4564-05 AIR-CORE COILL217,218 L92-0446-05 BEADS CORE

L219,220 L34-4564-05 AIR-CORE COILL221,222 L34-4563-05 AIR-CORE COILL223 L41-8285-14 SMALL FIXED INDUCTOR(820NH)L225 L40-8265-92 SMALL FIXED INDUCTOR(8.2NH) K4,K5,K6L227 ∗ L41-1075-16 SMALL FIXED INDUCTOR(10NH) K4,K5,K6

L228 ∗ L41-1875-45 SMALL FIXED INDUCTOR(18NH)L300 L41-1878-14 SMALL FIXED INDUCTOR(18NH) K,K2,K3L300 L41-2778-14 SMALL FIXED INDUCTOR(27NH) K4,K5,K6L301,302 L41-3978-14 SMALL FIXED INDUCTOR(39NH)L303 L41-4778-14 SMALL FIXED INDUCTOR(47NH) K,K2,K3

L303 L41-5678-14 SMALL FIXED INDUCTOR(56NH) K4,K5,K6L304 L40-4763-92 SMALL FIXED INDUCTOR(4.7NH) K4,K5,K6L306 L41-1085-45 SMALL FIXED INDUCTOR(100NH) K4,K5,K6L306 ∗ L41-1285-45 SMALL FIXED INDUCTOR(120NH) K,K2,K3L307 L92-0446-05 BEADS CORE

L308 ∗ L41-5675-45 SMALL FIXED INDUCTOR(56NH) K,K2,K3L308 ∗ L41-8275-45 SMALL FIXED INDUCTOR(82NH) K4,K5,K6L309 L41-1878-14 SMALL FIXED INDUCTOR(18NH) K,K2,K3L309-312 L41-2778-14 SMALL FIXED INDUCTOR(27NH) K4,K5,K6L310 L41-2278-14 SMALL FIXED INDUCTOR(22NH) K,K2,K3

L311,312 L41-1878-14 SMALL FIXED INDUCTOR(18NH) K,K2,K3L313 L40-1575-57 SMALL FIXED INDUCTOR(15.0NH)L314 L40-1875-57 SMALL FIXED INDUCTOR(18.0NH)L315 L40-2275-57 SMALL FIXED INDUCTOR(22.0NH) K,K2,K3L316,317 L39-1272-15 TOROIDAL COIL

L318 L92-0163-05 BEADS COREL319 L39-1272-15 TOROIDAL COILL321,322 L41-5685-14 SMALL FIXED INDUCTOR(560NH)L323 L40-6881-37 SMALL FIXED INDUCTOR(0.680UH)L324 L40-1885-92 SMALL FIXED INDUCTOR(180NH)

L325 L40-1091-86 SMALL FIXED INDUCTOR(1.0UH)L326 L41-1585-14 SMALL FIXED INDUCTOR(150NH)L327 L41-1085-14 SMALL FIXED INDUCTOR(100NH)L450-452 L92-0446-05 BEADS COREL600 L92-0136-05 CHIP FERRITE

L601,602 L92-0408-05 CHIP FERRITEL603,604 L92-0163-05 BEADS COREL605 L92-0140-05 CHIP FERRITEL606,607 L92-0446-05 BEADS COREL608 L92-0161-05 BEADS CORE

L609 L92-0138-05 CHIP FERRITEL610 L92-0446-05 BEADS COREL611,612 L92-0408-05 CHIP FERRITEL613 L92-0149-05 CHIP FERRITEL614 L92-0140-05 CHIP FERRITE

If a part reference number is listed in a shaded box, that part does not come with the PCB.

Page 33: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

33

L615 L92-0161-05 BEADS COREL616-628 L92-0446-05 BEADS COREL629 L92-0163-05 BEADS COREL700 L92-0149-05 CHIP FERRITEL701-704 L92-0408-05 CHIP FERRITE

L705,706 L33-1462-05 SMALL FIXED INDUCTORL707 L33-1469-05 SMALL FIXED INDUCTORL708,709 L92-0163-05 BEADS COREL800-805 L92-0446-05 BEADS CORE K2,K3,K5L800-805 L92-0446-05 BEADS CORE K6

L803-805 L92-0446-05 BEADS CORE K,K4L807 ∗ L33-1494-05 SMALL FIXED INDUCTOR

X1 L77-1802-05 CRYSTAL RESONATOR(32768HZ)X100 ∗ L77-3013-05 TCXO(16.8MHZ)X300 L77-1961-05 VCXO(16.8MHZ)X450 L77-1962-05 VCXO(18.432MHZ)

XF300 L71-0551-45 MCF(49.95MHZ)

CP1 R90-0743-05 MULTIPLE RESISTORCP2 R90-0745-05 MULTIPLE RESISTORCP3 -5 R90-0740-05 MULTIPLE RESISTORCP6 ,7 R90-0741-05 MULTIPLE RESISTORCP8 -12 R90-0740-05 MULTIPLE RESISTOR

CP13-16 R90-0743-05 MULTIPLE RESISTORCP100,101 R90-0741-05 MULTIPLE RESISTOR

R3 RK73HB1J473J CHIP R 47K J 1/16WR5 RK73HB1J474J CHIP R 470K J 1/16WR7 RK73HB1J473J CHIP R 47K J 1/16WR8 RK73HB1J103J CHIP R 10K J 1/16WR9 RK73HB1J104J CHIP R 100K J 1/16W

R10 RK73HB1J473J CHIP R 47K J 1/16WR11 -14 RK73HB1J474J CHIP R 470K J 1/16WR15 RK73HB1J104J CHIP R 100K J 1/16WR16 RK73HB1J474J CHIP R 470K J 1/16WR17 RK73HB1J124J CHIP R 120K J 1/16W

R18 ,19 RK73HB1J100J CHIP R 10 J 1/16WR20 RK73GB2A000J CHIP R 0.0 J 1/10WR21 RK73HB1J473J CHIP R 47K J 1/16WR22 RK73HH1J224D CHIP R 220K D 1/16WR23 RK73HH1J104D CHIP R 100K D 1/16W

R24 RK73HB1J103J CHIP R 10K J 1/16WR26 RK73HB1J103J CHIP R 10K J 1/16WR27 RK73HB1J102J CHIP R 1.0K J 1/16WR28 ,29 RK73HB1J473J CHIP R 47K J 1/16WR31 ,32 RK73HB1J474J CHIP R 470K J 1/16W

R33 RK73HB1J473J CHIP R 47K J 1/16WR34 RK73HB1J474J CHIP R 470K J 1/16WR35 RK73HB1J473J CHIP R 47K J 1/16WR38 ,39 RK73HB1J471J CHIP R 470 J 1/16WR40 -45 RK73HB1J101J CHIP R 100 J 1/16W

R46 RK73HB1J473J CHIP R 47K J 1/16WR47 RK73HB1J101J CHIP R 100 J 1/16WR48 RK73HB1J000J CHIP R 0.0 J 1/16WR49 ,50 RK73HB1J101J CHIP R 100 J 1/16WR51 RK73HB1J474J CHIP R 470K J 1/16W

R52 RK73HB1J104J CHIP R 100K J 1/16WR53 -56 RK73HB1J101J CHIP R 100 J 1/16WR57 RK73HB1J474J CHIP R 470K J 1/16WR59 RK73HB1J474J CHIP R 470K J 1/16W

R62 RK73HB1J104J CHIP R 100K J 1/16W

R63 RK73HB1J473J CHIP R 47K J 1/16WR66 RK73HB1J104J CHIP R 100K J 1/16WR67 RK73HB1J473J CHIP R 47K J 1/16WR69 -76 RK73HB1J473J CHIP R 47K J 1/16WR77 RK73HB1J105J CHIP R 1.0M J 1/16W

R101 RK73HB1J474J CHIP R 470K J 1/16WR102 RK73HB1J473J CHIP R 47K J 1/16WR105 RK73HB1J470J CHIP R 47 J 1/16WR106 RK73HB1J101J CHIP R 100 J 1/16WR109 RK73HB1J102J CHIP R 1.0K J 1/16W

R110 RK73HB1J104J CHIP R 100K J 1/16WR111 RK73HB1J101J CHIP R 100 J 1/16WR112 RK73HB1J100J CHIP R 10 J 1/16WR113 RK73HB1J474J CHIP R 470K J 1/16WR114 RK73HH1J184D CHIP R 180K D 1/16W

R115 RK73HB1J100J CHIP R 10 J 1/16WR116 RK73HH1J473D CHIP R 47K D 1/16WR117 RK73HB1J183J CHIP R 18K J 1/16WR118 RK73HB1J332J CHIP R 3.3K J 1/16WR119 RK73HB1J102J CHIP R 1.0K J 1/16W

R120 ∗ RK73HB1J106J CHIP R 10M J 1/16WR121 RK73HB1J122J CHIP R 1.2K J 1/16WR122 RK73HB1J392J CHIP R 3.9K J 1/16WR123,124 RK73HB1J000J CHIP R 0.0 J 1/16WR125 RK73HB1J122J CHIP R 1.2K J 1/16W

R127 RK73HB1J682J CHIP R 6.8K J 1/16WR128 RK73HB1J470J CHIP R 47 J 1/16WR129 RK73HB1J122J CHIP R 1.2K J 1/16WR130 RK73HB1J104J CHIP R 100K J 1/16WR131 RK73HB1J122J CHIP R 1.2K J 1/16W

R132,133 RK73HB1J000J CHIP R 0.0 J 1/16WR134 RK73HB1J332J CHIP R 3.3K J 1/16WR135 RK73HB1J472J CHIP R 4.7K J 1/16WR136 RK73HB1J223J CHIP R 22K J 1/16W K,K2,K3R136 RK73HB1J333J CHIP R 33K J 1/16W K4,K5,K6

R137 RK73HB1J152J CHIP R 1.5K J 1/16WR138 RK73HB1J104J CHIP R 100K J 1/16WR139 RK73HB1J474J CHIP R 470K J 1/16WR140 RK73HB1J473J CHIP R 47K J 1/16WR141 RK73HB1J000J CHIP R 0.0 J 1/16W K,K2,K3

R142,143 RK73HB1J473J CHIP R 47K J 1/16W K4,K5,K6R144 RK73HB1J102J CHIP R 1.0K J 1/16WR145 RK73HB1J104J CHIP R 100K J 1/16WR146 RK73HB1J221J CHIP R 220 J 1/16W K,K2,K3R146,147 RK73HB1J221J CHIP R 220 J 1/16W K4,K5,K6

R147 RK73HB1J271J CHIP R 270 J 1/16W K,K2,K3R148 RK73HB1J220J CHIP R 22 J 1/16WR149 RK73HB1J154J CHIP R 150K J 1/16WR150 RK73HB1J101J CHIP R 100 J 1/16WR151 RK73HB1J560J CHIP R 56 J 1/16W

R152 RK73HB1J220J CHIP R 22 J 1/16W K,K2,K3R153 RK73HB1J101J CHIP R 100 J 1/16WR155 RK73HB1J270J CHIP R 27 J 1/16W K4,K5,K6R155 RK73HB1J390J CHIP R 39 J 1/16W K,K2,K3R156 RK73HB1J151J CHIP R 150 J 1/16W K,K2,K3

R156 RK73HB1J181J CHIP R 180 J 1/16W K4,K5,K6R157,158 RK73HB1J473J CHIP R 47K J 1/16W K4,K5,K6R159 RK73HB1J224J CHIP R 220K J 1/16W K,K2,K3

If a part reference number is listed in a shaded box, that part does not come with the PCB.

Page 34: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

34

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

R160 RK73HB1J151J CHIP R 150 J 1/16W K,K2,K3R160 RK73HB1J181J CHIP R 180 J 1/16W K4,K5,K6

R162 RK73HB1J103J CHIP R 10K J 1/16WR163 RK73HB1J000J CHIP R 0.0 J 1/16W K,K2,K3R164 RK73HB1J103J CHIP R 10K J 1/16W K,K2,K3R164,165 RK73HB1J103J CHIP R 10K J 1/16W K4,K5,K6R166 RK73HB1J331J CHIP R 330 J 1/16W

R167 RK73HB1J221J CHIP R 220 J 1/16WR170 RK73HB1J000J CHIP R 0.0 J 1/16WR172 RK73HB1J222J CHIP R 2.2K J 1/16WR173 ∗ RK73HB1J106J CHIP R 10M J 1/16WR174,175 RK73HB1J271J CHIP R 270 J 1/16W K4,K5,K6

R175 RK73HB1J000J CHIP R 0.0 J 1/16W K,K2,K3R176 RK73FB2B000J CHIP R 0.0 J 1/8WR177 RK73HB1J104J CHIP R 100K J 1/16WR178 RK73HB1J560J CHIP R 56 J 1/16WR200 RK73HB1J332J CHIP R 3.3K J 1/16W

R201 RK73HB1J152J CHIP R 1.5K J 1/16W K,K2,K3R201 RK73HB1J182J CHIP R 1.8K J 1/16W K4,K5,K6R202 RK73HB1J472J CHIP R 4.7K J 1/16WR203 RK73HB1J330J CHIP R 33 J 1/16WR204 RK73HB1J331J CHIP R 330 J 1/16W

R205 RK73HB1J220J CHIP R 22 J 1/16WR211 RK73HB1J331J CHIP R 330 J 1/16WR212,213 RK73HB1J104J CHIP R 100K J 1/16WR214 RK73HB1J181J CHIP R 180 J 1/16W K,K2,K3R214 RK73HB1J271J CHIP R 270 J 1/16W K4,K5,K6

R215 RK73HB1J180J CHIP R 18 J 1/16W K4,K5,K6R215 RK73HB1J330J CHIP R 33 J 1/16W K,K2,K3R216 RK73HB1J181J CHIP R 180 J 1/16W K,K2,K3R216 RK73HB1J271J CHIP R 270 J 1/16W K4,K5,K6R217 RK73HB1J101J CHIP R 100 J 1/16W

R218 RK73HB1J223J CHIP R 22K J 1/16WR219 RK73HB1J103J CHIP R 10K J 1/16WR220 RK73EB2HR22F CHIP R 0.22 F 1/2WR221 RK73GB2A220J CHIP R 22 J 1/10W K4,K5,K6R221 RK73GB2A470J CHIP R 47 J 1/10W K,K2,K3

R222 RK73EB2HR22F CHIP R 0.22 F 1/2WR223 RK73HB1J473J CHIP R 47K J 1/16WR224-226 RK73HH1J154D CHIP R 150K D 1/16WR227 RK73HB1J220J CHIP R 22 J 1/16WR228 RK73HB1J103J CHIP R 10K J 1/16W

R229 RK73HH1J154D CHIP R 150K D 1/16WR230 RK73HB1J333J CHIP R 33K J 1/16WR231,232 RK73HH1J154D CHIP R 150K D 1/16WR233 RK73GB2A000J CHIP R 0.0 J 1/10W K4,K5,K6R233 ∗ RK73GB2A1R0J CHIP R 1.0 J 1/10W K,K2,K3

R234 RK73HB1J103J CHIP R 10K J 1/16WR235 RK73HB1J105J CHIP R 1.0M J 1/16WR236 RK73HB1J473J CHIP R 47K J 1/16WR237 RK73HB1J184J CHIP R 180K J 1/16WR238 RK73HB1J474J CHIP R 470K J 1/16W

R239 RK73HB1J104J CHIP R 100K J 1/16WR240 RK73HB1J222J CHIP R 2.2K J 1/16WR242 RK73FB2B000J CHIP R 0.0 J 1/8W K,K2,K3R243 RK73GB2A271J CHIP R 270 J 1/10WR244 RK73HB1J333J CHIP R 33K J 1/16W

R245 RK73HB1J472J CHIP R 4.7K J 1/16WR246 RK73GB2A271J CHIP R 270 J 1/10W

R247 RK73HB1J272J CHIP R 2.7K J 1/16WR249 RK73GB2A000J CHIP R 0.0 J 1/10W K,K2,K3R251 RK73HB1J104J CHIP R 100K J 1/16W

R252 RK73HB1J183J CHIP R 18K J 1/16WR254,255 RK73HB1J103J CHIP R 10K J 1/16WR256 RK73FB2B102J CHIP R 1.0K J 1/8WR258 RK73GB2A272J CHIP R 2.7K J 1/10WR259,260 RK73GB2A000J CHIP R 0.0 J 1/10W

R261 RK73HB1J101J CHIP R 100 J 1/16WR262 RK73HB1J222J CHIP R 2.2K J 1/16WR263 RK73HB1J822J CHIP R 8.2K J 1/16WR264 RK73HB1J000J CHIP R 0.0 J 1/16WR300 RK73HB1J103J CHIP R 10K J 1/16W

R301 RK73HB1J104J CHIP R 100K J 1/16WR302 RK73HB1J564J CHIP R 560K J 1/16WR303,304 RK73HB1J103J CHIP R 10K J 1/16WR305 RK73HB1J473J CHIP R 47K J 1/16WR306 RK73HB1J104J CHIP R 100K J 1/16W

R307 RK73HB1J274J CHIP R 270K J 1/16WR308 RK73HB1J103J CHIP R 10K J 1/16WR309,310 RK73HB1J105J CHIP R 1.0M J 1/16WR312 RK73HB1J104J CHIP R 100K J 1/16WR313 RK73HB1J473J CHIP R 47K J 1/16W K4,K5,K6

R313 RK73HB1J683J CHIP R 68K J 1/16W K,K2,K3R314 RK73HB1J104J CHIP R 100K J 1/16WR316 RK73HB1J121J CHIP R 120 J 1/16W K,K2,K3R316 RK73HB1J560J CHIP R 56 J 1/16W K4,K5,K6R317 RK73HB1J220J CHIP R 22 J 1/16W K4,K5,K6

R317 RK73HB1J270J CHIP R 27 J 1/16W K,K2,K3R318-321 RK73HB1J104J CHIP R 100K J 1/16WR322 RK73HB1J271J CHIP R 270 J 1/16WR323 RK73HB1J220J CHIP R 22 J 1/16WR324,325 RK73HB1J271J CHIP R 270 J 1/16W

R326 RK73HB1J222J CHIP R 2.2K J 1/16WR327 RK73HB1J332J CHIP R 3.3K J 1/16WR328 RK73HB1J100J CHIP R 10 J 1/16WR329,330 RK73FB2B000J CHIP R 0.0 J 1/8WR333 RK73HH1J104D CHIP R 100K D 1/16W

R334 RK73HH1J473D CHIP R 47K D 1/16WR335 RK73HB1J681J CHIP R 680 J 1/16WR336,337 RK73HB1J470J CHIP R 47 J 1/16WR338 RK73HB1J221J CHIP R 220 J 1/16WR339 RK73GB2A000J CHIP R 0.0 J 1/10W

R340 RK73HB1J822J CHIP R 8.2K J 1/16WR341 RK73HB1J470J CHIP R 47 J 1/16WR342 RK73HB1J684J CHIP R 680K J 1/16WR343,344 RK73HB1J392J CHIP R 3.9K J 1/16WR347 RK73HB1J102J CHIP R 1.0K J 1/16W

R348,349 RK73HB1J220J CHIP R 22 J 1/16WR353 RK73HB1J154J CHIP R 150K J 1/16WR356 RK73HB1J153J CHIP R 15K J 1/16WR357 RK73HB1J563J CHIP R 56K J 1/16WR358 RK73HB1J472J CHIP R 4.7K J 1/16W

R359 RK73HB1J182J CHIP R 1.8K J 1/16WR360 RK73HB1J392J CHIP R 3.9K J 1/16WR361 RK73HB1J332J CHIP R 3.3K J 1/16WR362 RK73HB1J272J CHIP R 2.7K J 1/16WR364 RK73HB1J392J CHIP R 3.9K J 1/16W

R365 RK73HB1J473J CHIP R 47K J 1/16W

Page 35: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

35

R366 RK73HB1J220J CHIP R 22 J 1/16WR368 RK73HB1J104J CHIP R 100K J 1/16WR370 RK73HB1J470J CHIP R 47 J 1/16WR372 RK73HB1J470J CHIP R 47 J 1/16W

R374 RK73HB1J270J CHIP R 27 J 1/16W K,K2,K3R374 RK73HB1J470J CHIP R 47 J 1/16W K4,K5,K6R450 RK73HB1J474J CHIP R 470K J 1/16WR451,452 RK73HB1J223J CHIP R 22K J 1/16WR453 RK73HB1J474J CHIP R 470K J 1/16W

R454 RK73HB1J103J CHIP R 10K J 1/16WR455 RK73HB1J223J CHIP R 22K J 1/16WR456 RK73HH1J154D CHIP R 150K D 1/16WR457 RK73HH1J104D CHIP R 100K D 1/16WR458 RK73HB1J105J CHIP R 1.0M J 1/16W

R459 RK73HB1J103J CHIP R 10K J 1/16WR460 RK73HB1J471J CHIP R 470 J 1/16WR461 RK73HB1J394J CHIP R 390K J 1/16WR462 RK73HB1J333J CHIP R 33K J 1/16WR463 RK73HB1J222J CHIP R 2.2K J 1/16W

R464 RK73HB1J223J CHIP R 22K J 1/16WR465 RK73HB1J472J CHIP R 4.7K J 1/16WR466 RK73HB1J182J CHIP R 1.8K J 1/16WR467 RK73HB1J474J CHIP R 470K J 1/16WR468 RK73HB1J333J CHIP R 33K J 1/16W

R469 RK73HB1J224J CHIP R 220K J 1/16WR470 RK73HB1J474J CHIP R 470K J 1/16WR471 RK73HB1J100J CHIP R 10 J 1/16WR472 RK73HB1J474J CHIP R 470K J 1/16WR473 RK73HB1J000J CHIP R 0.0 J 1/16W

R474 RK73HB1J124J CHIP R 120K J 1/16WR475 RK73HB1J333J CHIP R 33K J 1/16WR476 RK73HB1J474J CHIP R 470K J 1/16WR477 RK73HB1J105J CHIP R 1.0M J 1/16WR478 RK73HB1J224J CHIP R 220K J 1/16W

R479 RK73HB1J474J CHIP R 470K J 1/16WR480 RK73HB1J473J CHIP R 47K J 1/16WR481 RK73HB1J103J CHIP R 10K J 1/16WR482 RK73HB1J104J CHIP R 100K J 1/16WR483 RK73HB1J103J CHIP R 10K J 1/16W

R484 RK73HB1J470J CHIP R 47 J 1/16WR485 RK73HB1J472J CHIP R 4.7K J 1/16WR487 RK73HB1J473J CHIP R 47K J 1/16WR488 RK73HB1J103J CHIP R 10K J 1/16WR489,490 RK73HB1J104J CHIP R 100K J 1/16W

R491 RK73HB1J272J CHIP R 2.7K J 1/16WR492 RK73HB1J100J CHIP R 10 J 1/16WR493 RK73HB1J4R7J CHIP R 4.7 J 1/16WR494 RK73HB1J100J CHIP R 10 J 1/16WR495 RK73HB1J224J CHIP R 220K J 1/16W

R496 RK73HB1J472J CHIP R 4.7K J 1/16WR498 RK73HB1J220J CHIP R 22 J 1/16WR499 RK73HB1J332J CHIP R 3.3K J 1/16WR500 RK73HB1J470J CHIP R 47 J 1/16WR502,503 RK73HB1J100J CHIP R 10 J 1/16W

R505-507 RK73HB1J100J CHIP R 10 J 1/16WR508 RK73HB1J103J CHIP R 10K J 1/16WR509 RK73HB1J470J CHIP R 47 J 1/16WR510-512 RK73HB1J474J CHIP R 470K J 1/16WR515 RK73HB1J000J CHIP R 0.0 J 1/16W

R516 RK73HB1J563J CHIP R 56K J 1/16WR517-519 RK73HB1J470J CHIP R 47 J 1/16WR520 RK73HB1J473J CHIP R 47K J 1/16WR522 RK73HB1J473J CHIP R 47K J 1/16WR524 RK73HB1J473J CHIP R 47K J 1/16W

R525 RK73HB1J184J CHIP R 180K J 1/16WR526 RK73HB1J470J CHIP R 47 J 1/16WR528 RK73HB1J102J CHIP R 1.0K J 1/16WR529 RK73HB1J103J CHIP R 10K J 1/16WR530,531 RK73HB1J102J CHIP R 1.0K J 1/16W

R532 RK73HB1J821J CHIP R 820 J 1/16WR533,534 RK73HB1J104J CHIP R 100K J 1/16WR535 RK73HB1J682J CHIP R 6.8K J 1/16WR537 RK73HB1J333J CHIP R 33K J 1/16WR538 RK73HB1J473J CHIP R 47K J 1/16W

R539 RK73HB1J100J CHIP R 10 J 1/16WR542 RK73HB1J333J CHIP R 33K J 1/16WR544 RK73HB1J100J CHIP R 10 J 1/16WR545 RK73HB1J473J CHIP R 47K J 1/16WR546 RK73HB1J124J CHIP R 120K J 1/16W

R550 RK73HB1J105J CHIP R 1.0M J 1/16WR552 RK73HB1J223J CHIP R 22K J 1/16WR553 RK73HB1J393J CHIP R 39K J 1/16WR554 RK73HB1J470J CHIP R 47 J 1/16WR556 RK73HB1J333J CHIP R 33K J 1/16W

R557 RK73HB1J470J CHIP R 47 J 1/16WR558 RK73HB1J104J CHIP R 100K J 1/16WR559 RK73HB1J470J CHIP R 47 J 1/16WR560 RK73HB1J104J CHIP R 100K J 1/16WR561 RK73HB1J333J CHIP R 33K J 1/16W

R562 RK73HB1J154J CHIP R 150K J 1/16WR563 RK73HB1J124J CHIP R 120K J 1/16WR564,565 RK73HB1J105J CHIP R 1.0M J 1/16WR566 RK73HB1J103J CHIP R 10K J 1/16WR567 RK73HB1J104J CHIP R 100K J 1/16W

R568 RK73HB1J103J CHIP R 10K J 1/16WR570 RK73HB1J332J CHIP R 3.3K J 1/16WR571 RK73HB1J104J CHIP R 100K J 1/16WR572 RK73HB1J472J CHIP R 4.7K J 1/16WR573 RK73HB1J100J CHIP R 10 J 1/16W

R574-576 RK73HB1J474J CHIP R 470K J 1/16WR577 RK73HB1J473J CHIP R 47K J 1/16WR579 RK73HB1J104J CHIP R 100K J 1/16WR580 RK73HB1J100J CHIP R 10 J 1/16WR581 RK73HB1J470J CHIP R 47 J 1/16W

R582 RK73HB1J474J CHIP R 470K J 1/16WR583,584 RK73HB1J470J CHIP R 47 J 1/16WR585,586 RK73HB1J474J CHIP R 470K J 1/16WR587 RK73HB1J102J CHIP R 1.0K J 1/16WR589 RK73HB1J104J CHIP R 100K J 1/16W

R590 RK73HB1J102J CHIP R 1.0K J 1/16WR591 RK73HB1J683J CHIP R 68K J 1/16WR592 RK73HB1J102J CHIP R 1.0K J 1/16WR593 RK73HB1J103J CHIP R 10K J 1/16WR595 RK73GB2A822J CHIP R 8.2K J 1/10W

R596 RK73HB1J124J CHIP R 120K J 1/16WR597 RK73HB1J104J CHIP R 100K J 1/16WR600-604 RK73HB1J474J CHIP R 470K J 1/16WR605 RK73HB1J000J CHIP R 0.0 J 1/16WR606,607 RK73HB1J474J CHIP R 470K J 1/16W

Page 36: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

36

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

R608 RK73HB1J105J CHIP R 1.0M J 1/16WR609 RK73HB1J474J CHIP R 470K J 1/16WR610-612 RK73HB1J102J CHIP R 1.0K J 1/16WR613 RK73HB1J471J CHIP R 470 J 1/16WR614-616 RK73HB1J102J CHIP R 1.0K J 1/16W

R617,618 RK73HB1J471J CHIP R 470 J 1/16WR619 RK73HB1J474J CHIP R 470K J 1/16WR620 RK73HB1J473J CHIP R 47K J 1/16WR621 RK73HB1J104J CHIP R 100K J 1/16WR622 RK73HB1J474J CHIP R 470K J 1/16W

R625 RK73HB1J103J CHIP R 10K J 1/16WR626 RK73HB1J473J CHIP R 47K J 1/16WR628 RK73HB1J470J CHIP R 47 J 1/16WR629 RK73HB1J103J CHIP R 10K J 1/16WR630 RK73HB1J473J CHIP R 47K J 1/16W

R631 RK73HB1J470J CHIP R 47 J 1/16WR632,633 RK73HB1J000J CHIP R 0.0 J 1/16WR634 RK73HB1J103J CHIP R 10K J 1/16WR635 RK73HB1J000J CHIP R 0.0 J 1/16WR636 RK73HB1J183J CHIP R 18K J 1/16W

R637-639 RK73HB1J102J CHIP R 1.0K J 1/16WR640-643 RK73HB1J474J CHIP R 470K J 1/16WR644 RK73HB1J392J CHIP R 3.9K J 1/16WR645 RK73HB1J104J CHIP R 100K J 1/16WR647 RK73HB1J104J CHIP R 100K J 1/16W

R648,649 RK73HB1J392J CHIP R 3.9K J 1/16WR650 RK73HB1J472J CHIP R 4.7K J 1/16WR651 RK73HB1J103J CHIP R 10K J 1/16WR652 RK73HB1J000J CHIP R 0.0 J 1/16WR653 RK73HB1J100J CHIP R 10 J 1/16W

R657 RK73HB1J102J CHIP R 1.0K J 1/16WR658 RK73HB1J471J CHIP R 470 J 1/16WR659 RK73HB1J102J CHIP R 1.0K J 1/16WR661 RK73HB1J102J CHIP R 1.0K J 1/16WR663,664 RK73HB1J102J CHIP R 1.0K J 1/16W

R665 RK73HB1J000J CHIP R 0.0 J 1/16WR666 RK73HB1J102J CHIP R 1.0K J 1/16WR672-682 RK73HB1J101J CHIP R 100 J 1/16W K2,K3,K5R672-682 RK73HB1J101J CHIP R 100 J 1/16W K6R684 RK73HB1J104J CHIP R 100K J 1/16W

R685,686 RK73HB1J474J CHIP R 470K J 1/16WR687,688 RK73HB1J000J CHIP R 0.0 J 1/16WR690 RK73HB1J331J CHIP R 330 J 1/16WR691 RK73HB1J000J CHIP R 0.0 J 1/16WR701 RK73HB1J102J CHIP R 1.0K J 1/16W

R702 RK73HB1J104J CHIP R 100K J 1/16WR705 RK73HB1J102J CHIP R 1.0K J 1/16WR706 RK73HB1J331J CHIP R 330 J 1/16WR707 RK73HB1J104J CHIP R 100K J 1/16WR708 RK73HB1J272J CHIP R 2.7K J 1/16W

R709 RK73HB1J470J CHIP R 47 J 1/16WR710 RK73HB1J333J CHIP R 33K J 1/16WR711 RK73HB1J122J CHIP R 1.2K J 1/16WR713 RK73HB1J105J CHIP R 1.0M J 1/16WR714 RK73HB1J104J CHIP R 100K J 1/16W

R718 RK73HB1J105J CHIP R 1.0M J 1/16WR719 RK73HB1J470J CHIP R 47 J 1/16WR720,721 RK73HB1J105J CHIP R 1.0M J 1/16WR722 RK73HB1J102J CHIP R 1.0K J 1/16WR723 RK73HB1J104J CHIP R 100K J 1/16W

R726 RK73HB1J000J CHIP R 0.0 J 1/16WR728 RK73HB1J222J CHIP R 2.2K J 1/16WR729 RK73HB1J223J CHIP R 22K J 1/16WR730 RK73HB1J102J CHIP R 1.0K J 1/16WR731 RK73HB1J684J CHIP R 680K J 1/16W

R732,733 RK73HB1J154J CHIP R 150K J 1/16WR734 RK73HB1J184J CHIP R 180K J 1/16WR735 RK73HB1J330J CHIP R 33 J 1/16WR737 RK73HB1J470J CHIP R 47 J 1/16WR738 RK73HB1J273J CHIP R 27K J 1/16W

R739 RK73HB1J223J CHIP R 22K J 1/16WR741 RK73HB1J473J CHIP R 47K J 1/16WR742 RK73HB1J182J CHIP R 1.8K J 1/16WR743,744 RK73HB1J223J CHIP R 22K J 1/16WR745,746 RK73HB1J473J CHIP R 47K J 1/16W

R747 RK73HB1J182J CHIP R 1.8K J 1/16WR748 RK73HB1J103J CHIP R 10K J 1/16WR753 RK73GB2A2R2J CHIP R 2.2 J 1/10WR754 RK73HB1J330J CHIP R 33 J 1/16WR758,759 RK73GB2A2R2J CHIP R 2.2 J 1/10W

R762 RK73GB2A100J CHIP R 10 J 1/10WR768 RK73HB1J154J CHIP R 150K J 1/16WR770 RK73HB1J224J CHIP R 220K J 1/16WR771 RK73HB1J123J CHIP R 12K J 1/16WR772 RK73HB1J334J CHIP R 330K J 1/16W

R773 RK73HB1J124J CHIP R 120K J 1/16WR774 RK73HH1J334D CHIP R 330K D 1/16WR775 RK73HH1J223D CHIP R 22K D 1/16WR784 RK73HB1J474J CHIP R 470K J 1/16WR790 RK73HB1J103J CHIP R 10K J 1/16W

R796,797 RK73HB1J104J CHIP R 100K J 1/16WR798 RK73HB1J474J CHIP R 470K J 1/16WR801 ∗ RK73HB1J106J CHIP R 10M J 1/16W K2,K3,K5R801 ∗ RK73HB1J106J CHIP R 10M J 1/16W K6R804 RK73GB2A000J CHIP R 0.0 J 1/10W K2,K3,K5

R804 RK73GB2A000J CHIP R 0.0 J 1/10W K6R805 RK73GH2A104D CHIP R 100K D 1/10W K2,K3,K5R805 RK73GH2A104D CHIP R 100K D 1/10W K6R806 RK73GJ1J333D CHIP R 33K D 1/16W K2,K3,K5R806 RK73GJ1J333D CHIP R 33K D 1/16W K6

R807-810 RK73HB1J102J CHIP R 1.0K J 1/16W K2,K5R807-822 RK73HB1J102J CHIP R 1.0K J 1/16W K3,K6R823,824 RK73HB1J223J CHIP R 22K J 1/16W K2,K3,K5R823,824 RK73HB1J223J CHIP R 22K J 1/16W K6R825,826 RK73HB1J101J CHIP R 100 J 1/16W K2,K3,K5

R825,826 RK73HB1J101J CHIP R 100 J 1/16W K6R827 RK73HH1J223D CHIP R 22K D 1/16W K2,K3,K5R827 RK73HH1J223D CHIP R 22K D 1/16W K6R828 RK73HB1J474J CHIP R 470K J 1/16W K2,K3,K5R828 RK73HB1J474J CHIP R 470K J 1/16W K6

R829,830 RK73HB1J101J CHIP R 100 J 1/16W K3,K6R831-833 RK73HB1J181J CHIP R 180 J 1/16W K2,K3,K5R831-833 RK73HB1J181J CHIP R 180 J 1/16W K6R835 RK73HB1J474J CHIP R 470K J 1/16W K2,K3,K5R835 RK73HB1J474J CHIP R 470K J 1/16W K6

R836 RK73HB1J222J CHIP R 2.2K J 1/16W K2,K3,K5R836 RK73HB1J222J CHIP R 2.2K J 1/16W K6R839 RK73HB1J102J CHIP R 1.0K J 1/16WR840 RK73HB1J474J CHIP R 470K J 1/16WR841 RK73HB1J102J CHIP R 1.0K J 1/16W

Page 37: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

37

R842 RK73HB1J104J CHIP R 100K J 1/16WR843 RK73HB1J474J CHIP R 470K J 1/16WR844 RK73HB1J471J CHIP R 470 J 1/16WR845,846 RK73HB1J474J CHIP R 470K J 1/16WR847-850 RK73HB1J102J CHIP R 1.0K J 1/16W K,K4

R847-852 RK73HB1J102J CHIP R 1.0K J 1/16W K2,K3,K5R847-852 RK73HB1J102J CHIP R 1.0K J 1/16W K6R852 RK73HB1J102J CHIP R 1.0K J 1/16W K,K4R853 RK73HB1J474J CHIP R 470K J 1/16WR854 RK73HB1J471J CHIP R 470 J 1/16W

R855-860 RK73HB1J102J CHIP R 1.0K J 1/16W

S901 S64-0406-05 LEVER SWITCHS902 S70-0496-05 TACT SWITCH

D1 MA2S111-F DIODED102 1SV325F VARIABLE CAPACITANCE DIODED104-109 1SV282-F VARIABLE CAPACITANCE DIODED110 1SV325F VARIABLE CAPACITANCE DIODED111,112 1SV282-F VARIABLE CAPACITANCE DIODE

D113,114 HVC131 DIODE K4,K5,K6D115 1SV278F VARIABLE CAPACITANCE DIODED116,117 HVC131 DIODE K4,K5,K6D118 MA2S111-F DIODED119 DA221 DIODE

D200 HVC131 DIODED201 HZU5CLL ZENER DIODED202-205 HVC131 DIODED206,207 ∗ EZJZ0V50023C VARISTORD301,302 1SV286F VARIABLE CAPACITANCE DIODE

D304-307 1SV286F VARIABLE CAPACITANCE DIODED308 HVC131 DIODED450,451 RB706F-40 DIODED452 MA2S111-F DIODED453 RB706F-40 DIODE

D454,455 1SS388F DIODED600 1SR154-400 DIODED601,602 AVRM1005C270M VARISTORD609 NNCD6.8G-A ZENER DIODED611 NNCD6.8G-A ZENER DIODE

D700,701 1SS388F DIODED702 NNCD6.8G-A ZENER DIODED703 1SS301F DIODED704 HRB0502A DIODED705,706 DA221 DIODE

D707 CUS01 DIODED708 MA2S111-F DIODED710,711 AVRM1005C270M VARISTORD804,805 IMN10 DIODE K2,K3,K5D804,805 IMN10 DIODE K6

D813,814 IMN10 DIODE K3,K6D815 DTZ3.9(B) ZENER DIODE K2,K3,K5D815 DTZ3.9(B) ZENER DIODE K6D816-818 IMN10 DIODE K3,K6D817,818 IMN10 DIODE K,K2,K4

D817,818 IMN10 DIODE K5

IC1 MM1522XURE ANALOGUE ICIC2 RV5C386A MOS-ICIC3 AT2425610TI27 ROM ICIC4 ∗ S-80930CNNB-G MOS-IC

IC5 ∗ 30625MGP346HU MICROPROCESSOR IC

IC6 Note 1 ROM ICIC7 ∗ TC7S08FU-F MOS-ICIC8 Note 1 MICROPROCESSOR ICIC100 LMC7101BIM5 MOS-ICIC101 ADF4111BCP7 MOS-IC

IC200 TC75W51FK(F) MOS-ICIC201 TA75W01FUF MOS-ICIC202,203 ∗ MASWSS0181 ANALOGUE ICIC300,301 LMC7101BIM5 MOS-ICIC302 SPM5001 MOS-IC

IC303 TC7W53FK(F) MOS-ICIC304 ∗ TA31137FNG MOS-ICIC305-307 TC7W53FK(F) MOS-ICIC308 ∗ TC7WU04FK-F MOS-ICIC450 TC7W66FK-F MOS-IC

IC451,452 TC75W51FK(F) MOS-ICIC453 ∗ TC7WH74FK-F MOS-ICIC454 AK4550VTP MOS-ICIC455 ∗ TC7WU04FK-F MOS-ICIC456 TC75W51FK(F) MOS-IC

IC457 EX128TQ64I630C MOS-ICIC458 TC7W66FK-F MOS-ICIC459 TC75W51FK(F) MOS-ICIC460 TC7W66FK-F MOS-ICIC461 TC75S51FE(F) MOS-IC

IC462 M62364FP-F MOS-ICIC463 TC75W51FK(F) MOS-ICIC600 XC6204B502PR MOS-ICIC601 XC6204B502MR MOS-ICIC602 TC7W53FK(F) MOS-IC

IC603 TC74VHCT244AFT MOS-ICIC604,605 TC7SBD384AFU MOS-ICIC606 BU4094BCFV MOS-ICIC607 TC7MB3245FK MOS-ICIC608,609 TC7WB125FK MOS-IC

IC610 TK11250CUCB MOS-ICIC701 TC7W66FK-F MOS-ICIC702,703 LM4906LD ANALOGUE ICIC704 ∗ XC6204B302M MOS-ICIC705 TC75W51FK(F) MOS-IC

IC706 XC61CC5602NR MOS-ICIC707,708 XC6204B332M MOS-ICIC709 ∗ XC9225A15CM MOS-ICIC710 XC6365D103M MOS-ICIC711 XC6204B252M MOS-IC

IC712 TK11250CUCB MOS-ICIC713 XC9101D09AKR ANALOGUE ICIC800 LMC7101BIM5 MOS-IC K2,K3,K5IC800 LMC7101BIM5 MOS-IC K6IC801-803 BU4094BCFV MOS-IC

Q100 2SC4617(S) TRANSISTORQ101,102 SSM6L05FU FETQ103 2SK879(Y)F FETQ104 2SC4617(S) TRANSISTORQ105 SSM6L05FU FET

Q106 2SK508NV(K52) FET K,K2,K3Q106,107 2SK508NV(K52) FET K4,K5,K6Q107 2SK508NV(52K) FET K,K2,K3

Note 1 : This part cannot be replaced. Therefore, this part is not supplied as a service part.

Page 38: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310PARTS LIST

38

Ref. No. Parts No. DescriptionAddressNewpartsRef. No. Parts No. DescriptionAddress

Newparts Destination Destination

TX-RX UNIT (X57-7250-XX)

Q108 2SJ347F FETQ109 2SC5108(Y)F TRANSISTOR K,K2,K3

Q109-112 2SC5108(Y)F TRANSISTOR K4,K5,K6Q111,112 2SC5108(Y)F TRANSISTOR K,K2,K3Q200 2SC5108(Y)F TRANSISTORQ202 RD01MUS1-T113 FETQ203 SSM3K15TE(F) FET

Q204 ∗ RD07MVS2 FETQ205 EMD9 TRANSISTORQ206 SSM3K15TE(F) FETQ207 DTA144EE DIGITAL TRANSISTORQ208 SSM3K15TE(F) FET

Q209 2SJ243-A FETQ210 2SK3077F FETQ300 2SC4617(S) TRANSISTORQ301 3SK318 FETQ302 ∗ 2SK1215-E(E) FET

Q303 2SC5108(Y)F TRANSISTORQ304 EMD9 TRANSISTORQ450 2SC4738(GR)F TRANSISTORQ451 2SA1832(GR)F TRANSISTORQ452,453 SSM3K15TE(F) FET

Q454,455 2SJ347F FETQ456,457 SSM3K15TE(F) FETQ459 SSM3K15TE(F) FETQ460 2SC4617(S) TRANSISTORQ461 SSM3K15TE(F) FET

Q600-602 SSM6L05FU FETQ603 SSM3K15TE(F) FETQ604 ∗ TPC6108-F FETQ605,606 UM6K1N FETQ700 SSM3K15TE(F) FET

Q701 UMG3N TRANSISTORQ702 2SB798(DL,DK) TRANSISTORQ703 SSM3K15TE(F) FETQ704 2SJ243-A FETQ705 SSM3K15TE(F) FET

Q706 2SJ243-A FETQ708 SSM3K15TE(F) FETQ709 UMC4N TRANSISTORQ710 ∗ TPC6108-F FETQ711 SSM5H01TU FET

Q712,713 UM6K1N FETQ800 2SC4617(S) TRANSISTOR K2,K3,K5Q800 2SC4617(S) TRANSISTOR K6Q801 2SB798(DL,DK) TRANSISTOR K2,K3,K5Q801 2SB798(DL,DK) TRANSISTOR K6

Q802 SSM3K15TE(F) FETQ803,804 SSM6L05FU FET

TH200 B57331V2104J THERMISTOR

Page 39: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

39

TK-5310

A B

1

2

3

CF301

XF300

88

41Px2

Px2

Px2

Px2

P

Px3

PP

P

Px2 Px2

Px2

P

8713

1

43

Control PCB(X57 B/5)

97

53

33

44

4374

4

32

12

6

55

36

30

90

91

71

5731

56

34

F

20(K)23(K4)

Dx2Dx2

Cx2

Cx2

38

702

73

96

76

9452

27

7564 42

45

65

48x2

47

50

68

49

8569 7

966

70

61 1480

5

62

54

28

35

77

51

93

52

9472

86

8384

63

B

K

N Q

QQ

A

Ex2

B

H

IJ

700

701

39 8

76 Top PCB(X57 C/5)

ANT PCB (X57 E/5)

TX-RX PCB(X57 A/5)

Option PCB(X57 D/5)

EXPLODED VIEW (TK-5310 K, K4)

Parts with the exploded numbers larger than 700 are not supplied.

A :N08-0531-14B :N09-2439-25C :N09-2440-15D :N09-2441-15E :N09-2442-15

F :N09-2443-14H :N14-0813-14I :N14-0814-14J :N14-0815-04K :N14-0817-14

M :N30-3008-60N :N32-2004-48P :N83-2005-48Q :N83-2006-43

Note: If a part reference number is listed in a box on the

exploded view of the PCB, that part does not come

with the PCB. These parts must be ordered

separately.

Page 40: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

40

TK-5310

C D

1

2

3

CF301

XF300

44

41

60

46

10

11

37

92

78x2

Px2

Px2Px2

Px2

P

Px3

PP

P

Px2 Px2

Px2

P

42x2

82 81

A 2

3

43

97

Control PCB(X57 B/5)

53

33

4

32

12

30

90

91

7134

21(K2)22(K3)24(K5)25(K6)Dx2

Dx2

Cx2Cx2

38

73

96

76

9452

27

7564 42

45

65

48x2

47

50

68

49

8569 7

966

70

61 1480

5

62

54

28

35

77

51

93

52

9472

86

8384

63

B

K

N Q

QQ

Ex2

B

H

IJ

95

29

88

8713

39 8

76

700

701

74

TX-RX PCB(X57 A/5)

Option PCB(X57 D/5)

ANT PCB (X57 E/5)43

Top PCB(X57 C/5)

6

55

36

5731

56

F

702

EXPLODED VIEW (TK-5310 K2,K3, K5, K6)

Parts with the exploded numbers larger than 700 are not supplied.

A :N08-0531-14B :N09-2439-25C :N09-2440-15D :N09-2441-15E :N09-2442-15

F :N09-2443-14H :N14-0813-14I :N14-0814-14J :N14-0815-04K :N14-0817-14

M :N30-3008-60N :N32-2004-48P :N83-2005-48Q :N83-2006-43

Note: If a part reference number is listed in a box on the

exploded view of the PCB, that part does not come

with the PCB. These parts must be ordered

separately.

Page 41: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

41

TK-5310PACKING

E F

1

2

3

Parts with the exploded numbers larger than 700 are not supplied.

18. INSTRUCTION MANUAL (ENGLISH(B62-1972-00) /FRENCH)

15. SUB-INSTRUCTION MANUAL(QRC/ENGLISH) (B59-2393-00)

17. PAMPHLET(B59-2448-00)

16. SUB-INSTRUCTION MANUAL(QRC/FRENCH)(B59-2439-00)

8. CAP(SP/MIC)(B09-0682-13)

A.DRESSED SCREW(CAP)(N08-0531-14)

M. PAN HEAD MACHINE SCREW (N30-3008-60) x2

703

704

39. RUBBER SHEET(CAP)(G11-4340-04)

67. BELT CLIP(J29-0730-05)

59. ITEM CARTON CASE(H52-2174-02)

Page 42: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

42

• Key operation

Key Function Display

[Selector] Test frequency channel up/down Channel No.

[Concentric switch] Channel spacing switching Wide :"W"

(Position "A":Wide, Narrow :"N"Position "B":Narrow, P25 :"A"

Position "C":P25)

[Lever switch] RF output power switching Low power :"LO"

(_:Low power, -:High power) High power :"HI"

[PTT] Transmit -

[Side1] Squelch level change Squelch level 0:"SQ.LV0"(0t1t2t • • • t9t0t1t2t • • • ) Squelch level 1:"SQ.LV1"

Squelch level 9:"SQ.LV9"

[Side1] Hold Squelch off

[Side2] MSK baud rate change 2400bps: icon

(1200bps/2400bps) appears

[Side2] Hold Compander on/off On: icon appears

[Side3] Shifts to the Panel tuning mode -

[Side3] Hold LCD all lights LCD all point appears

[Orange] Beat shift on/off On: icon appears

[A] Unused -

[B] Unused -

[C] Test signaling down Signaling No.

[D] Test signaling up Signaling No.

[0] to [9] and Use as the DTMF keypad. -[#], [*] If a key is pressed during transmission,

the DTMF corresponding to the

key that was presses is sent.

• LED indicatorRed LED Lights during transmission. Blinks at the low

battery voltage warning.Green LED Lights when there is carrier.

• LCD display in the panel test mode

• Filter Mode

Display Condition Key

W WIDE (25kHz) Filter Concentric switch "A"

N NARROW (12.5kHz) Filter Concentric switch "B"

A P25 (12.5kHz) Filter Concentric switch "C"

ADJUSTMENT

A B

C

6

MIC

Volume

Selector

Side 1 key

Side 2 key

PTT switch

Concentric Switch

Lever switchOrange key

Universalconnector

Side 3 key

Controls

Panel Test Mode (K2, K3, K5 and K6 models only)

For the K, K4 models (without LCD), perform "Test mode"using the KPG-95D.

Test mode operation featuresThis transceiver has a test mode. To enter panel test

mode, press and hold the [Side3] and [PTT] keys whileturning the transceiver power on and then the [PTT] keyfirst. Test mode can be inhibited by programming. To exittest mode, switch the power on again.

• When the panel test mode is activated, the channel se-lected with the [Selector] knob and the last used signalingnumber are displayed. When it is activated for the firsttime, the signaling number is 1.

• If test signaling 20 (Tone Test Pattern) is selected, the re-sult of Bit Error Rate (BER) calculation is displayed on theLCD. The BER value is also output from the serial port.

• The P25 and analog modes are switched automatically byselecting test signaling. When P25 mode is effective, “A”is displayed on the LCD.

LOW

1-1 [ None ]SQ.LV1

Channel No. Signaling No.

W: WideN : NarrowA : P25

Page 43: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

43

ADJUSTMENT

Panel Tuning Mode (K2, K3, K5 and K6 models only)

The transceiver is adjusted in this mode.For the K model (without LCD), perform "Tuning mode"

using the KPG-95D.

Preparations for tuning the transceiverBefore attempting to tune the transceiver, connect the

unit to a suitable power supply.Whenever the transmitter is turned, the unit must be con-

nected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with a

8Ω dummy load and connected to an AC voltmeter and anaudio distortion meter or a SINAD measurement meter at alltimes during tuning.

To enter the Panel Tuning ModePress the [Side3] key in the panel test mode.Use the [B] key to write tuning data through tuning modes,

and the [C] and [D] keys to adjust tuning requirements (1 to256 appears on the LCD).

Use the [A] key to select the adjustment item through tun-ing modes. Use the [Side1] key to adjust 3 or 5 reference leveladjustments, and use the [Concentric switch] to switch be-tween Wide/Narrow/P25. (Position "A":Wide, Position"B":Narrow, Position "C":P25)

• LCD display in the panel tuning mode

Frequency and SignalingThe transceiver has been adjusted for the frequencies

shown in the following table. When required, readjust themfollowing the adjustment procedure to obtain the frequenciesyou want in actual operation.

• Test Frequency

• Test Signaling

Signaling RX Signaling TX Signaling P25/

No. Analog

1 None None Analog

2 None 100Hz Square wave Analog

3 QT 67.0Hz QT 67.0Hz Analog

4 QT 151.4Hz QT 151.4Hz Analog

5 QT 210.7Hz QT 210.7Hz Analog

6 QT 254.1Hz QT 254.1Hz Analog

7 DQT 023N DQT 023N Analog

8 DQT 445N DQT 445N Analog

9 DQT 754I DQT 754I Analog

10 DTMF Code "159D" DTMF Code "159D" Analog

11 None DTMF Code "9" Analog

12 None 1633Hz Single Tone Analog

13 2-tone: 2-tone: Analog

A : 304.7Hz A : 304.7Hz

B : 3106.0Hz B : 3106.0Hz

14 Single Tone : 979.9Hz Single Tone : 979.9Hz Analog

15 None MSK PN Pattern Analog

16 MSK MSK Analog

Sync : 0x052B Sync : 0x052B

Data : 0x230960C6AAAA Data : 0x230960C6AAAA

CRC : 0xC4D7 CRC : 0xC4D7

17 NAC 293 NAC 293 P25

18 NAC 023 NAC 023 P25

19 NAC 5EA NAC 5EA P25

20 1011Hz Tone Test Pattern 1011Hz Tone Test Pattern P25

21 NAC 293 Silence Pattern P25

22 NAC 293 Calibration Pattern P25

23 NAC 293 Transmitter Test Pattern P25

24 NAC 293 Symbol Rate Pattern P25

25 NAC 293 Low Deviation Pattern P25

26 NAC 293 Fidelity Pattern P25

LOW

NXT SETBalance 256

Adjustmentvalue(1~256)

Adjustmentitem

W: WideN : NarrowA : P25

CHK, K2, K3 K4, K5, K6

RX (MHz) TX (MHz) RX (MHz) TX (MHz)

1 485.05000 485.10000 425.05000 425.10000

2 450.05000 450.10000 380.05000 380.10000

3 519.95000 519.90000 469.95000 469.90000

4 485.00000 485.00000 425.00000 425.00000

5 485.20000 485.20000 425.20000 425.20000

6 485.40000 485.40000 425.40000 425.40000

7~16 - - - -

Page 44: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

44

ADJUSTMENT

• Key operation

Key Function

[Selector] Unused

[Concentric switch] Channel spacing switching (Position "A": Wide,

Position "B": Narrow, Position "C": P25)

[Lever switch] Unused

[PTT] Transmission. When the battery low voltage is

adjusted, the adjustment value is displayed on the LCD.

[Side1] To enter 3, 5 or 7 reference level adjustments

[Side2] Unused

[Side3] Exit the panel tuning mode and shift to the

panel test mode.

[Orange] Unused

[A] Go to the next adjustment item

(The current adjustment data is cleared.)

[A] Hold Back to the last adjustment item

(The current adjustment data is cleared.)

[B] Write the new adjustment value to the transceiver.

[C] Adjustment value down

[D] Adjustment value up

3, 5 or 7 reference level adjustments frequency

• 3 or 5 reference level adjustments frequency

(Adjustment items other than assist voltage)

TX assist voltage

TuningDisplay

K, K2, K3 K4, K5, K6

point RX (MHz) TX (MHz) RX (MHz) TX (MHz)

Low L 450.10000 450.00000 380.10000 380.00000

Low' LC 467.60000 467.50000 402.60000 402.50000

Center C 485.10000 485.00000 425.10000 425.00000

High' CH 502.60000 502.50000 447.60000 447.50000

High H 519.90000 519.95000 469.90000 470.00000

• 7 reference level adjustments frequency

(Assist voltage adjustments)

Tuning point DisplayK, K2, K3 K4, K5, K6

TX (MHz)

Low L 450.10000 380.10000

Low'' L2 461.70000 394.60000

Low' L1 473.40000 409.10000

Center C 485.10000 423.60000

High' H1 496.70000 438.10000

High'' H2 508.30000 452.60000

High H 519.90000 469.90000

RX assist voltage

Tuning point DisplayK, K2, K3 K4, K5, K6

RX (MHz)

Low L 450.05000 380.05000

Low'' L2 458.35000 388.35000

Low' L1 466.65000 396.65000

Center C 474.95000 404.95000

High' H1 483.25000 413.25000

High'' H2 491.55000 421.55000

High H 499.94500 429.94500

Page 45: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

45

• Adjustment item and Display (***: 1~256)

No. Adjustment item Display Wide/Narrow/P25 Tuning point Note

1 RX assist voltage RX Assist *** - 7

2 TX assist voltage TX Assist *** - 7

3 RX front-end RX Front-end *** - 5 AF unmute

4 2nd local frequency 2nd Lo Freq *** - 1

5 Frequency Frequency *** - 1

6 High power High Power *** - 5

7 Low power Low Power *** - 3

8 Mic sensitivity Mic Sense *** - 1

9 Balance Balance *** Wide/Narrow/P25 W:5/N:1/A:1 100Hz Square Wave

10 FM maximum deviation FM Max Dev *** Wide/Narrow W:5/N:1

11 P25 High deviation APCO Hi Dev *** P25 A:5 Symbol Rate Pattern

12 QT deviation QT Dev *** Wide/Narrow W:5/N:1 QT : 67Hz

13 DQT deviation DQT Dev *** Wide/Narrow W:5/N:1 DQT : 023N

14 DTMF deviation DTMF Dev *** Wide/Narrow W:1/N:1 DTMF Code : 9

15 Single tone deviation Tone Dev *** Wide/Narrow W:1/N:1 Single Tone : 1633Hz

16 MSK deviation MSK Dev *** Wide/Narrow W:1/N:1 MSK PN Pattern

17 Squelch (Threshold:1) Squelch (1) *** Wide/Narrow/P25 W:3/N:3/A:3 AF unmute

18 Squelch (Tight:9) Squelch (9) *** Wide/Narrow W:3/N:3 AF unmute

19 RSSI (Reference) RSSI (Ref) *** Wide/P25 W:3/A:3

20 RSSI (-120dBm) RSSI (-120) *** Wide W:3

21 RSSI (-70dBm) RSSI (-70) *** Wide W:3

22 Battery TX inhibit voltage Battery *** - 1

ADJUSTMENT

Page 46: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

46

ADJUSTMENTADJUSTMENT

Flow Chart

RX Assist

[A]

[Side 1] 7 reference leveladjustments

[Side 1] 7 reference leveladjustments

[Side 1] 5 reference leveladjustments

[Side 1] 5 reference leveladjustments

[Side 1] 5 reference leveladjustments

[Side 1] 3 reference leveladjustments

[Side 1] 3 reference leveladjustments

[Side 1] 3 reference leveladjustments

[Side 1] 5 reference leveladjustments

[Side 1] 3 reference leveladjustments

[Side 1] 3 reference leveladjustments

[Side 1] 5 reference leveladjustments

[Side 1] 5 reference leveladjustments

[Side 1] 5 reference leveladjustments

Panel Test Mode

(Panel Tuning Mode)

[Side 3][Side 3]

TX Assist

[A]

[Concentric SW]B

[Concentric SW]B [Concentric SW]C

[Concentric SW]B C

[Concentric SW]A

[Concentric SW]A

[Concentric SW]A

[Concentric SW]B,C[Concentric SW]A

[Concentric SW]C

RX Front-end

[A]

2nd Lo Freq

[A]

Frequency

[A]

High Power

[A]

APCO Hi Dev

[A]

[A] [A] [A]

Low Power

[A]

[Side 1]5 reference leveladjustments

5 reference leveladjustments exit

[Side 1]

L

LC

H[Side 1]

[Side 1]C

[Side 1]CH

Low

Low'

High

Center

High'

[A]

[A]

[A]

[A]

[A]

[Side 1]7 reference leveladjustments

7 reference leveladjustments exit

[Side 1]

L

L2

H[Side 1]

[Side 1]L1

[Side 1]H2

Low

Low''

High

Low'

High''

[A]

[A]

[A][Side 1]

C

[Side 1]H1

Center

High'

[A]

[A]

[A]

[A]

[Side 1]3 reference leveladjustments

3 reference leveladjustments exit

L

H[Side 1]

[Side 1]C

Low

High

Center

[A]

[A]

[A]

Mic Sense

[A]

RSSI(Ref)

[A]

[A] [Side 1][Side 1]

[Side 1]

Balance Wide Balance Narrow

[A] [A]

FM Max Dev Wide FM Max Dev Narrow

[Concentric SW]B,C[Concentric SW]A

[Concentric SW]B[Concentric SW]B

[Concentric SW]A

[Concentric SW]A

[A] [A]

QT Dev Wide QT Dev Narrow

[Concentric SW]A

[Concentric SW]A

[A] [A]

DQT Dev Wide DQT Dev Narrow

[A] [A]

DTMF Dev Wide DTMF Dev Narrow

[Concentric SW]A

[A] [A]

Tone Dev Wide Tone Dev Narrow

[Concentric SW]A

[A] [A]

MSK Dev Wide MSK Dev Narrow

[Concentric SW]A

[A]

[A]

Squelch(1) Wide Squelch(1) Narrow Squelch(1) P25

[A]

[Concentric SW]B,C[Concentric SW]A

[Concentric SW]A

Squelch(9) Wide

Wide

Wide

Wide

Squelch(9) Narrow

Balance P25

RSSI(-120)

[A]

RSSI(-70)

[A]

Battery

[A]

B

B,C

B,C

B,C

B,C

B,C

B,C

B [Concentric SW]B C

B,C

[Side 1] 3 reference leveladjustments

[Side 1][A]

[Concentric SW]B,C[Concentric SW]A

[Concentric SW]A

Squelch(9) P25

B,C

Page 47: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

47

BER (Bit Error Rate) Measurement1. The Panel Test Mode is used to measure the BER (Refer

to "Test mode operation features" described on page 41.).2. Select ”20” for test signaling (Refer to "Test Signaling"

described on page 42.).When "20" is selected for the test signaling, the filter isautomatically selected to "P25".(If there is no RF input signal, the display shows”500000”)

3. Select a filter (Refer to "Filter Mode" described on page41.).

4. Select a test frequency (Refer to "Test Frequency" de-scribed on page 42.).

C4FM (P25) Deviation Adjustment1. The transceiver adjusts the deviation between High Devia-

tion ±1800Hz for the C4FM (P25).2. The Symbol Rate Pattern is used when adjusting the High

Deviation for the C4FM (P25) (Refer to "Test Signaling" de-scribed on page 42.). This test signal has a peak deviationequal to π/2 1800Hz = 2827Hz.

Service Jig

Nut wrenchIn order to turn the volume nut and the channel selector

nut, use a recommendation tool.KENWOOD part No. : W05-1123-00

5. Measure the BER (Bit Error Rate) using the digital radiotester. Enter a standard input signal into the transceiver asa standard tone test pattern.

6. Adjust the input signal level to achieve the standard biterror rate (BER).(For example, if the BER is 5%, the display shows”050000”.)

ADJUSTMENT

Adjustment Points

S

2nd Lo

+

TX-RX UNIT (A/5) : TX-RX section

Foil side

BPF GND

BPF

CVCLKC

32kout

Page 48: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

48

ADJUSTMENT

Test Equipment Required for AlignmentTest Equipment Major Specifications

1. Standard Signal Generator Frequency Range 350 to 520MHz(SSG) Modulation Frequency modulation and external modulation

Output -127dBm/0.1µV to greater than -47dBm/1mV2. Power Meter Input Impedance 50Ω

Operation Frequency 350 to 520MHz or moreMeasurement Range Vicinity of 10W

3. Deviation Meter Frequency Range 350 to 520MHz4. Digital Volt Meter Measuring Range 10mV to 10V DC

(DVM) Input Impedance High input impedance for minimum circuit loading5. Oscilloscope DC through 30MHz6. High Sensitivity Frequency Range 10Hz to 1000MHz

Frequency Counter Frequency Stability 0.2ppm or less7. Ammeter 5A8. AF Volt Meter Frequency Range 50Hz to 10kHz

(AF VTVM) Voltage Range 1mV to 10V9. Audio Generator (AG) Frequency Range 50Hz to 5kHz or more

Output 0 to 1V10. Distortion Meter Capability 3% or less at 1kHz

Input Level 50mV to 10Vrms11. Spectrum Analyzer Measuring Range DC to 1GHz or more12. Tracking Generator Center frequency 50kHz to 600MHz

Output Voltage 100mV or more13. 8Ω Dummy Load Approx. 8Ω, 3W14. Regulated Power Supply 5V to 10V, approx. 3A

Useful if ammeter equipped

The following parts are required for

adjustment

1. Antenna connector adapter

The antenna connector of this transceiver uses an SMAterminal.

Use an antenna connector adapter [SMA(f) – BNC(f) orSMA(f) – N(f)] for adjustment. (The adapter is not provided asan option, so buy a commercially-available one.)

Note :

When the antenna connector adapter touches the knob,draw out the knob to mount the connector.

2. Battery Jig

The optional KBP-6 battery case can be used as a batteryJIG using the following modification (please refer to thefollowing diagram).

<Recommendation for TX inhibit voltage adjustment and itscheck method>

We recommend that you increase the DC power supplyvoltage to about 0.2 V higher than the "TX inhibit voltage" beforepressing the PTT switch. Then press the PTT switch anddecrease the DC power supply voltage to the target level (suchas 5.8 V) for the adjustment check in TX mode.

KBP-6

DC Power Supply

5.80V

+ Battery terminal

- Battery terminal

Sensing line

Notice :

The battery voltage for TX inhibit should be measured atthe "Battery terminal", such as the sensing line, not the DCpower supply terminal. Generally, there is approximately a0.1 to 0.3 V loss through the cable, causing a differencebetween the DC power supply and the Battery terminal.

Page 49: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

49

ADJUSTMENTADJUSTMENT

11 : GREEN (5M)

TUBE

SCREW

8 : YELLOW (PF SW)

2 : RED (RX AF OUTPUT)

3 : BLACK (RX AF OUTPUT)

10 : BROWN (GND)

6 : BROWN (MIC GND)

5 : WHITE (MIC INPUT)

7 : BLUE (PTT SW) GND → ON

RED (2)

BLK (3)

100µ 10V

100µ 10V

WHT(5)

BRN (6)

BLU (7)

BRN (10)

PTT SW

+

+

+

To transceiver

AF Voltmeter

Audio generator10µ 10V

3. Universal connectorUse the interface cable (KPG-36/36A) for PC tuning or the

lead wire with plug (E30-3287-18) and screw (N08-0535-08)for panel tuning. Connect the plug to the universal connectorof the transceiver and tighten the screw.

The lead wire with plug (E30-3287-18) and screw (N08-0535-08) terminals are as follows. Numbers are universalconnector terminal numbers.

Caution1. When connecting the plug to the universal connector of

the transceiver, a short circuit may occur. To prevent this,be sure to turn the transceiver POWER switch off.

2. Since the RX AF output is a BTL output, there is a DCcomponent. Isolate this with a capacitor or transformer asshown in the figure.

3. Do not connect an instrument between red or black and GND.

• Universal connector

• Panel tuning

1 : SSW

3 : SP–

5 : EMC

7 : PTT

9 : OPT

11 : 5M

13 : RXD

2 : SP+

GNDEXT ANTGND

4 : MSW

6 : ME

8 : PF

10 : E

12 : TXD

14 : NC

• PC tuning

Connect the wires to the PCB in the connector case ofinterface cable.

For output the wires out of the connector case, need toprocess the connector case.

Connector case

KPG-36/36A

Remove thescrew

PCB layout

Shield

AF voltmeter

Audio generator

100µ 10V

100µ 10V

10µ 10V

+

+

+

How to Remove the Flat Cable1. Gently draw out both sides of the connector lever uni-

formly in the direction of the arrow with tweezers.(CN606, CN613, CN800, CN802, CN803, CN804)CN613, CN800, CN802:K2, K3, K5 and K6 models only

Tweezers

Flat cable

Lever

Page 50: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

50

Flat-headscrewdriver

Flat cable

Lever

3. Gently depress the connector lever in the direction of thearrow with a flat-head screwdriver or tweezers.(CN902, CN903)

Lever

Flat cable

Flat-headscrewdriver

2. Gently rise up the connector lever in the direction of thearrow with a flat-head screwdriver or tweezers.(CN713)

Note : Gently push both sides of the connector lever, whenput in the flat cable.

ADJUSTMENT

Page 51: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

51

Common Section

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

1. Setting 1) BATT terminal voltage:7.5V2) SSG standard modulation

[Wide] MOD:1kHz,DEV:3kHz[Narrow] MOD:1kHz,DEV:1.5kHz

2. Assist [Panel tuning mode] Power meter Panel ANT Panel [C],[D] Change the 2.7V±0.1Vvoltage 1) Adj item:[RX Assist] DVM TX-RX CV adjustment value

Adjust:[***] (A/5) within the limit When adjusting the assist•RX 2) Adj item:[L RX Assist]t of the specified voltage in PC tuning mode,

[L2 RX Assist]t[L1 RX Assist]t voltage. slide the bar to indicate[C RX Assist]t[H1 RX Assist]t "VCO Lock Voltage" within[H2 RX Assist]t[H RX Assist] 2.7V±0.1V on Meter window.Adjust:[***]

Press [B] to store the adjustmentvalue after adjustment.

•TX 3) Adj item:[TX Assist]Adjust:[***]

4) Adj item:[L TX Assist]t[L2 TX Assist]t[L1 TX Assist]t[C TX Assist]t[H1 TX Assist]t[H2 TX Assist]t[H TX Assist]Adjust:[***]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.

3. RX Front-end 1) Adj item:[RX Front-end] Spectrum Panel ANT Panel [C],[D] Change theadjust Adjust:[***] analyzer TX-RX BPF adjustment values

2) Adj item:[L RX Front-end] Tracking (A/5) BPF GND to get the highestTK-5310 Spectrum analyzer setting generator peak points as(K,K2,K3) Center-f :450.1MHz shown to the right.

Span :400MHzRBW :3MHzVBW :3MHzSWP :20msTG level :-15dBmXdB/div :10dB

Press [B] to store the adjustmentvalue after adjustment.3) Adj item:[LC RX Front-end]

Spectrum analyzer settingCenter-f:467.6MHz

Press [B] to store the adjustmentvalue after adjustment.

4) Adj item:[C RX Front-end]Spectrum analyzer settingCenter-f:485.1MHz

Press [B] to store the adjustmentvalue after adjustment.

ADJUSTMENT

10dB / REF 0dB

1

1: -.7118 dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1450.1 MHz

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1467.6 MHz

1

1: -.0159 dB

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER1485.1 MHz

1

1: .1706 dB

Page 52: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

52

5) Adj item:[CH RX Front-end] Spectrum Panel ANT Panel [C],[D] Change theSpectrum analyzer setting analyzer TX-RX BPF adjustment valuesCenter-f:502.6MHz Tracking (A/5) BPF GND to get the highest

Press [B] to store the adjustment generator peak points asvalue after adjustment. shown to the right.

6) Adj item:[H RX Front-end]Spectrum analyzer settingCenter-f:519.9MHz

Press [B] to store the adjustmentvalue after adjustment.

TK-5310 1) Adj item:[RX Front-end](K4,K5,K6) Adjust:[***]

2) Adj item:[L RX Front-end]Spectrum analyzer setting

Center-f :380.1MHzSpan :400MHzRBW :3MHzVBW :3MHzSWP :20msTG level :-15dBmXdB/div :10dB

Press [B] to store the adjustmentvalue after adjustment.3) Adj item:[LC RX Front-end]

Spectrum analyzer settingCenter-f:402.6MHz

Press [B] to store the adjustmentvalue after adjustment.

4) Adj item:[C RX Front-end]Spectrum analyzer settingCenter-f:425.1MHz

Press [B] to store the adjustmentvalue after adjustment.

5) Adj item:[CH RX Front-end]Spectrum analyzer settingCenter-f:447.6MHz

Press [B] to store the adjustmentvalue after adjustment.

6) Adj item:[H RX Front-end]Spectrum analyzer settingCenter-f:469.9MHz

Press [B] to store the adjustmentvalue after adjustment.

ADJUSTMENT

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1502.6 MHz

1

1: .4359 dB

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1519.9 MHz

1

1: .6187 dB

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1380.1 MHz

1

1: 2.6337 dB

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1402.6 MHz

1

1: 1.2563 dB

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1425.1 MHz

1

1: .5693 dB

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1447.6 MHz

1

1: .3181 dB

10dB / REF 0dB

START 300.0 MHz STOP 700.0 MHz

MARKER 1469.9 MHz

1

1: .5120 dB

Page 53: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

53

4. 2nd local 1) Adj item:[2nd Lo Freq] f.counter TX-RX 2nd Lo Panel [C],[D] Change the 50.400MHz ±50Hzadjust Adjust:[***] (A/5) adjustment value

Press [B] to store the adjustment within the limit ofvalue after adjustment. the specified

frequency.5. RTC 1) CH-Sig:1-1 f.counter TX-RX CLKC Programming Adjust the RTC

oscillation DVM (A/5) 32kout Software: oscillation frequencyfrequency DC power KPG-95D using the PC tuningadjust supply mode. Perform the

procedures below.

1. Apply 5V DC tothe "CLKC" terminalof the TX-RX unit(X57-725) (A/5).

2. Measure the outputfrom the "32kout"terminal of the TX-RXunit (X57-725) (A/5)using the calibratedfrequency counter.

3. Enter the measuredfrequency value to"Crystal OscillationFrequency" of RTCcorrection in the PCtuning mode and thenclick [OK] button.

6. LCD 1) CH-Sig:1-1 Programming Adjust the LCD Note: Because thecontrast Software: contrast using the transceiver has aadjust KPG-95D PC tuning mode. function for revising a

change in temperature,Slide the bar to adjust adjust the LCD contrastthe value. The larger at room temperaturethe value, the darker (18 to 28 degrees).the LCD becomes;the lower the value,the more transparentthe LCD becomes.

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

ADJUSTMENT

Note: It is not necessaryto adjust the RTCoscillation frequency undernormal adjustments.The RTC oscillation frequencymust be checked andadjusted when the 32 kHzcrystal resonator (X1) isreplaced.

(Refer to“AdjustmentPoints” des-cribed onpage 47.)

Page 54: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

54

ADJUSTMENT

1. Frequency [Panel test mode] f.counter Panel ANT Panel [C],[D] K, K2, K3 Note:After replacing theadjust *1 1) CH-Sig:3-1 520.000130~ VCXO(X300) align frequency.

[Panel tuning mode] 520.000182MHz2) Adj item:[Frequency] K4, K5, K6

Adjust:[***] 470.000118~PTT:ON 470.000165MHz

Press [B] to store the adjustmentvalue after adjustment.

2. High power 1) Adj item:[High Power] Power meter 4.0W ±0.1Wadjust Adjust:[***] Ammeter 2.2A or less

2) Adj item:[L High Power]t[LC High Power]t[C High Power]t[CH High Power]t[H High Power]Adjust:[***]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.

3. Low power 1) Adj item:[Low Power] 1.0W ±0.1Wadjust Adjust:[***] 1.4A or less

2) Adj item:[L Low Power]t[C Low Power]t[H Low Power]Adjust:[***]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.

4. MIC 1) Adj item:[Mic Sense] Deviation Panel ANT Adjust AG input 15mV±3.5mVsensitivity Adjust:[129] meter Universal to get a standard Note:The SSW terminalcheck PTT:ON Oscilloscope connector MOD., 3.0kHz. (pin1) of the universal

Press [B] to store the adjustment AG connector must bevalue after adjustment. AF VTVM connected to GND

when checking theMIC sensitivity.

5. DQT balance 1) Adj item:[W Balance] Panel [C],[D] Make theadjust Adjust:[***] demodulation•Wide Deviation meter filter waves into

(Concentric SW:A) LPF:3kHz square waves.HPF:OFF

2) Adj item:[WL Balance]t[WLC Balance]t[WC Balance]t[WCH Balance]t[WH Balance]Adjust:[***]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.

Transmitter Section

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

*1: The reference oscillator frequency may drift due to shock (jarring the radio) or operating conditions. We recommend that the FrequencyAdjustment be checked each time the radio is serviced, or at least once per year. Maintenance should only be performed under normaltemperatures.

Page 55: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

55

ADJUSTMENT

•Narrow 3) Adj item:[N Balance] Deviation Panel ANT Set it to the adjustment(Concentric SW:B) meter Universal value obtained from

Oscilloscope connector the [WC Balance]AG adjustment of stepAF VTVM 2), using the [C] and

•P25 4) Adj item:[A Balance] [D] keys.(Concentric SW:C) After setting the

adjustment value,press [B] key.The adjustmentvalue will be storedin memory.

6. Max DEV 1) Adj item:[W FM Max Dev] Panel [C],[D] 4.0kHz ±50Hzadjust Adjust:[***] (According to the•Wide AG:1kHz/150mV at MIC terminal larger +, -)

(Concentric SW:A) Deviation meter filterLPF:15kHzHPF:OFF

2) Adj item:[WL FM Max Dev]t[WLC FM Max Dev]t[WC FM Max Dev]t[WCH FM Max Dev]t[WH FM Max Dev]Adjust:[***]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.

•Narrow 3) Adj item:[N FM Max Dev] 2.0kHz ±50Hz(Concentric SW:B, C) Adjust:[***] (According to the

PTT:ON larger +, -)Press [B] to store the adjustmentvalue after adjustment.

7. P25 high 1) Adj item:[A APCO Hi Dev] Power meter Panel ANT Panel [C],[D] 2827Hz 2771~2883Hzdeviation Adjust:[***] Deviation Universaladjust Deviation meter filter meter connector

LPF:3kHz OscilloscopeHPF:OFF AG

2) Adj item:[AL APCO Hi Dev]t AF VTVM[ALC APCO Hi Dev]t[AC APCO Hi Dev]t[ACH APCO Hi Dev]t[AH APCO Hi Dev]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

Page 56: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

56

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

8. QT deviation 1) Adj item:[W QT Dev] Power meter Panel ANT Panel [C],[D] 0.75kHz ±50Hzadjust Adjust:[***] Deviation Universal•Wide Deviation meter filter meter connector

(Concentric SW:A) LPF:3kHz OscilloscopeHPF:OFF AG

2) Adj item:[WC QT Dev] AF VTVMAdjust:[***]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.3) Adj item:[WL QT Dev]t Set it to the adjustment

[WLC QT Dev]t[WCH QT Dev]t value obtained from[WH QT Dev] the [WC QT Dev]

•Narrow 4) Adj item:[N QT Dev] adjustment of a step(Concentric SW:B,C) 2), using the [C] and

[D] keys.After setting theadjustment value,press [B] key.The adjustmentvalue will be storedin memory.

9. DQT 1) Adj item:[W DQT Dev] Panel [C],[D] 0.75kHz ±50Hzdeviation Adjust:[***]adjust Deviation meter filter•Wide LPF:3kHz

(Concentric SW:A) HPF:OFF2) Adj item:[WC DQT Dev]

Adjust:[***]PTT:ON

Press [B] to store the adjustmentvalue after adjustment.3) Adj item:[WL DQT Dev]t Set it to the adjustment

[WLC DQT Dev]t[WCH DQT Dev]t value obtained from[WH DQT Dev] the [WC DQT Dev]

•Narrow 4) Adj item:[N DQT Dev] adjustment of a step(Concentric SW:B, C) 2), using the [C] and

[D] keys.After setting theadjustment value,press [B] key.The adjustmentvalue will be storedin memory.

ADJUSTMENT

Page 57: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

57

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

ADJUSTMENT

10.DTMF 1) Adj item:[W DTMF Dev] Power meter Panel ANT Panel [C],[D] 3.0kHz ±50Hzdeviation Adjust:[***] Deviation Universaladjust Deviation meter filter meter connector•Wide LPF:15kHz Oscilloscope

(Concentric SW:A) HPF:OFF AGPTT:ON AF VTVM

Press [B] to store the adjustmentvalue after adjustment.

•Narrow 2) Adj item:[N DTMF Dev] Set it to the adjustment(Concentric SW:B, C) value obtained from

the [W DTMF Dev]adjustment of a step1), using the [C] and[D] keys.After setting theadjustment value,press [B] key.The adjustmentvalue will be storedin memory.

11.Single tone 1) Adj item:[W Tone Dev] Panel [C],[D] 3.0kHz ±50Hzdeviation Adjust:[***]adjust Deviation meter filter•Wide LPF:15kHz

(Concentric SW:A) HPF:OFFPTT:ON

Press [B] to store the adjustmentvalue after adjustment.

•Narrow 2) Adj item:[N Tone Dev] Set it to the adjustment(Concentric SW:B, C) value obtained from

the [W Tone Dev]adjustment of a step1), using the [C] and[D] keys.After setting theadjustment value,press [B] key.The adjustmentvalue will be storedin memory.

Page 58: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

58

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

12.MSK 1) Adj item:[W MSK Dev] Power meter Panel ANT Panel [C],[D] 3.0kHz ±50Hzdeviation Adjust:[***] Deviation Universaladjust Deviation meter filter meter connector•Wide LPF:15kHz Oscilloscope

(Concentric SW:A) HPF:OFF AGPTT:ON AF VTVM

Press [B] to store the adjustmentvalue after adjustment.

•Narrow 2) Adj item:[N MSK Dev] Set it to the adjustment(Concentric SW:B, C) value obtained from

the [W MSK Dev]adjustment of a step1), using the [C] and[D] keys.After setting theadjustment value,press [B] key.The adjustmentvalue will be storedin memory.

13.BATT 1) Adj item:[Battery] Power meter Panel ANT Panel After pressing the BATT terminal voltage:5.8VTX inhibit Adjust:[***] DVM BATT PTT switch, confirmvoltage PTT:ON terminal that one predeterminedadjust *2 numeric in the range

1 to 256 appears andthen press [B] key.That numeric will bestored in memory.

14.BATT [Panel test mode] Check The transceiver canTX inhibit 1) CH-Sig:1-1 transmit and the redvoltage BATT terminal voltage:6.0V LED blinking.Check *2 PTT:ON

BATT terminal voltage:5.8V The transceiver cannotPTT:ON transmit.

ADJUSTMENT

*2: Refer to “2. Batery Jig” described on page 48.

Page 59: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

59

1. AF level [Panel test mode] SSG Panel ANT Panel Volume Turn the Volume 0.63V±0.1VSetting 1) CH-Sig:1-1 DVM Universal Knob Knob to obtain

SSG output:-47dBm(1mV) AF VTVM connector 0.63V AF output.(MOD:1kHz/±3kHz) Dummy load

2. Sensitivity 1) CH-Sig:1-1 SSG Check 12dB SINAD or moreCheck SSG output:-118dBm(0.28µV) AF VTVM•Wide (MOD:1kHz/±3kHz) Oscilloscope

(Concentric SW:A) 2) CH-Sig:2-13) CH-Sig:3-1

•Narrow 4) CH-Sig:1-1(Concentric SW:B) SSG output:-118dBm(0.28µV)

(MOD:1kHz/±1.5kHz)5) CH-Sig:2-16) CH-Sig:3-1

3. RSSI [Panel tuning mode] Panel After inputreference 1) Adj item:[W RSSI(Ref)] signal from SSG,adjust Adjust:[***] press [B] key.•Wide 2) Adj item:[WL RSSI(Ref)]t That numeric

(Concentric SW:A) [WC RSSI(Ref)]t[WH RSSI(Ref)] will be storedAdjust:[***] in memory.SSG output:12dB SINAD level -3dB(MOD:1kHz/±3kHz)

•P25 3) Adj item:[AL RSSI(Ref)]t(Concentric SW:B,C) [AC RSSI(Ref)]t[AH RSSI(Ref)]

Adjust:[***]SSG output:12dB SINAD level (Wide)*Set to the SSG output level that 12dB SINAD is obtained at Wide.(MOD:1kHz/±3kHz)

4. Squelch 1) Adj item:[W Squelch(1)] After input After adjusting SQL,(Threshold) Adjust:[***] signal from SSG, check SQL open/close.adjust 2) Adj item:[WL Squelch(1)]t press [B] key. [Panel test mode]

•Wide [WC Squelch(1)]t[WH Squelch(1)] That numeric 1) CH-Sig:1-1(Concentric SW:A) Adjust:[***] will be stored SSG 12dB SINAD level

SSG output:12dB SINAD level -3dB in memory. -1.5dB:Open(MOD:1kHz/±3kHz) SSG -130dBm(0.07µV):Close

2) CH-Sig:2-1SSG 12dB SINAD level

-1.5dB:OpenSSG -130dBm(0.07µV):Close3) CH-Sig:3-1SSG 12dB SINAD level

-1.5dB:OpenSSG -130dBm(0.07µV):Close

ADJUSTMENT

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

Receiver Section

Page 60: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

60

•Narrow 3) Adj item:[N Squelch(1)] SSG Panel ANT Panel After input After adjusting SQL,(Concentric SW:B) Adjust:[***] AF VTVM Universal signal from SSG, check SQL open/Close.

4) Adj item:[NL Squelch(1)]t Oscilloscope connector press [B] key. [Panel test mode]

[NC Squelch(1)]t[NH Squelch(1)] That numeric 1) CH-Sig:1-1Adjust:[***] will be stored SSG 12dB SINAD levelSSG output:12dB SINAD level -4dB in memory. -1.5dB:Open(MOD:1kHz/±1.5kHz) SSG -130dBm(0.07µV):Close

•P25 5) Adj item:[A Squelch(1)] 2) CH-Sig:2-1(Concentric SW:C) Adjust:[***] SSG 12dB SINAD level

6) Adj item:[AL Squelch(1)]t -1.5dB:Open[AC Squelch(1)]t[AH Squelch(1)] SSG -130dBm(0.07µV):CloseAdjust:[***] 3) CH-Sig:3-1SSG output:12dB SINAD level (Wide) SSG 12dB SINAD level*Set to the SSG output level -1.5dB:Open that 12dB SINAD is obtained SSG -130dBm(0.07µV):Close at Wide.(MOD:1kHz/±3kHz)

5. Squelch 1) Adj item:[W Squelch(9)] After adjusting SQL,(Tight) Adjust:[***] check SQL open/close.adjust 2) Adj item:[WL Squelch(9)]t [Panel test mode]

•Wide [WC Squelch(9)]t[WH Squelch(9)] 1) CH-Sig:1-1(Concentric SW:A) Adjust:[***] SSG 12dB SINAD level

SSG output:12dB SINAD level +6dB +8dB:Open(MOD:1kHz/±3kHz) SSG 12dB SINAND level

:Close2) CH-Sig:2-1SSG 12dB SINAD level

+8dB:OpenSSG 12dB SINAD level

:Close3) CH-Sig:3-1SSG 12dB SINAD level

+8dB:OpenSSG 12dB SINAD level

:Close•Narrow 3) Adj item:[N Squelch(9)] After adjusting SQL,

(Concentric SW:B, C) Adjust:[***] check SQL open/close.SSG output:12dB SINAD level +6dB [Panel test mode]

(MOD:1kHz/±1.5kHz) 1) CH-Sig:1-1SSG -112dBm(0.562µV):OpenSSG -116dBm(0.35µV):Close2) CH-Sig:2-1SSG -112dBm(0.562µV):OpenSSG -117dBm(0.32µV):Close3) CH-Sig:3-1SSG -112dBm(0.562µV):OpenSSG -117dBm(0.32µV):Close

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

ADJUSTMENT

Page 61: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

61

6. RSSI 1) Adj item:[RSSI(-120)] SSG Panel ANT Panel After input(-120dBm) Adjust:[***] AF VTVM Universal signal from SSG,adjust 2) Adj item:[L RSSI(-120)]t Oscilloscope connector press [B] key.

[C RSSI(-120)]t[H RSSI(-120)] That numericAdjust:[***] will be storedSSG output:-120dBm(0.22µV) in memory.(MOD:1kHz/±3kHz)

7. RSSI 1) Adj item:[RSSI(-70)](-70dBm) Adjust:[***]adjust 2) Adj item:[L RSSI(-70)]t

[C RSSI(-70)]t[H RSSI(-70)]Adjust:[***]SSG output:-70dBm(70.8µV)(MOD:1kHz/±3kHz)

8. BER [Panel test mode] Digital Check 5% or less(Bit Error Rate) 1) CH-sig:1-20 radiocheck SSG output:-118dBm(0.28µV) tester

(C4FM)(1011Hz Tone Test Pattern)

Measurement Adjustment

Item Condition Test-Unit Terminal Unit Parts Method

Specifications/Remarksequipment

ADJUSTMENT

Page 62: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

62

TERMINAL FUNCTION

TX-RX unit (X57-7250-XX A/5) Pin Name I/O FunctionNo.Pin Name I/O FunctionNo.CN606

1 DSR I Data set ready2 E - GND3 RXD I Serial data input4 TXD O Serial data Output5 5M - 5V6 RTS1 O Request to Send7 REM I Programmable function key input8 PTT I External PTT input9 MICE - External MIC GND10 EMC I External MIC input11 MSW/CTS I EXT/INT MIC switch input12 SP- O BTL output - for external speaker13 SP+ O BTL output + for external speaker14 SSW I EXT/INT speaker switch input

CN609

1 OPT1 O Scramble code output 1 (Scrambler board)O Channel busy (ANI board)I Busy (VGS-1)

2 OPT3 O Scramble code output 2 (Scrambler board)I Key (ANI board)I Play (VGS-1)

3 RXD1 I Serial data input(VGS-1)4 TXD1 O PTT (Scrambler board)

O Serial data output (VGS-1)5 NC - No connection6 OPT4 I/O Echo PTT (Scrambler board)

O PTT (ANI board)O Enable (VGS-1)

7 USEL - GND8 OPT5 O Scramble code output 4 (Scrambler board)

O Emergency (ANI board)O Reset output(VGS-1)

9 DGND - GND10 AGND - GND11 AI I VGS Audio Input (VGS-1)12 AO O VGS Audio Output (VGS-1)13 AGND - GND14 5A - 5V15 STON I Side tone input(ANI board)16 DI/ANI I Data input (ANI board)17 TCONT I Speaker mute signal (ANI board)18 MAN DOWN O Man-down output (ANI board)19 INH I MIC mute signal input (ANI board)20 OPT2 O Scrambler control signal output

(Scrambler board)I Emergency signal input (ANI board)

21 TXO O MIC signal output (Scrambler board)22 RXEO O Audio signal output (Scrambler board)23 RXEI I Audio signal input (Scrambler board)24 TXI I MIC signal input (Scrambler board)25 OPT6 O Scramble code output 3 (Scrambler board)

26 SB2 O Switched B output

CN601 (for production)

1~20

CN612

1 GND - GND2 GND - GND3 MIC I External MIC input4 MICE - External MIC GND5 SP+ I BTL output + for external speaker6 PWR O Power control output7 SP+ I BTL output + for external speaker8 15V - 15V9 SP- I BTL output - for external speaker10 SB1 I Battery level input11 SP- I BTL output - for external speaker12 +B - Power input after passing through the fuse13 AF O Audio Output14 +B - Power input after passing through the fuse15 VOL I Volume level input16 +B - Power input after passing through the fuse17 CLK O Clock data output18 +B - Power input after passing through the fuse19 GND - GND20 LRST O LCD reset output21 KIN I Key input22 28M - 2.8V23 EXAFC O External AF output24 PSW I Power input after power switch25 KES O Key counter clear to send26 INAFC O Internal AF output27 DAT O Data output28 ECSW O Echo cancel MIC switch29 TGL0 I Lever switch input 030 33M - 3.3V31 TGL2 I Concentric switch input 232 33M - 3.3V33 TGL1 I Concentric switch input 134 33A - 3.3V35 CH_A I Rotary switch input 136 33A - 3.3V37 CH_B I Rotary switch input 238 25D - 2.5V39 CH_C I Rotary switch input 340 15D - 1.5V41 CH_D I Rotary switch input 442 15D - 1.5V43 PTT I PTT input44 5M - 5V45 36MD - 3V46 5M - 5V47 oE O Shift register OE48 LCDV - LCD contrast control voltage49 DGND - GND

Page 63: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

63

Pin Name I/O FunctionNo.

TERMINAL FUNCTION

Pin Name I/O FunctionNo.Pin Name I/O FunctionNo.

CN700

1 GND - GND2 GND - GND3 MIC O External MIC output4 MICE - External MIC GND5 SP+ O BTL output + for external speaker6 PWR I Power control input7 SP+ O BTL output + for external speaker8 15V - 15V9 SP- O BTL output - for external speaker10 SB1 O Battery Level output11 SP- O BTL output - for external speaker12 +B - Power input after passing through the fuse13 AF I Audio input14 +B - Power input after passing through the fuse15 VOL O Volume level output16 +B - Power input after passing through the fuse17 CLK I Clock data input18 +B - Power input after passing through the fuse19 GND - GND20 LRST I LCD reset input21 KIN O Key output22 28M - 2.8V23 EXAFC I External AF input24 PSW O Power output after power switch25 KES I Key counter clear to send26 INAFC I Internal AF input27 DAT I Data input28 ECSW I Echo cancel MIC switch29 TGL0 O Lever switch output 030 33M - 3.3V31 TGL2 O Concentric switch output 232 33M - 3.3V

33 TGL1 O Concentric switch output 134 33A - 3.3V35 CH_A O Rotary switch output 136 33A - 3.3V37 CH_B O Rotary switch output 238 25D - 2.5V39 CH_C O Rotary switch output 340 15D - 1.5V41 CH_D O Rotary switch output 442 15D - 1.5V43 PTT O PTT output44 5M - 5V45 36MD - 3V46 5M - 5V47 oE I Shift register OE48 LCDV - LCD contrast control voltage49 DGND - GND50 DGND - GND

CN713

1 INT SP- O BTL output - for internal speaker2 INT SP- O BTL output - for internal speaker3 INT SP+ O BTL output + for internal speaker4 INT SP+ O BTL output + for internal speaker5 INT MIC+ I Internal MIC input6 INT MIC- - Internal MIC GND

CN800 (K2, K3, K5 and K6 models only)

1 A0 I Adrress bus 02 GND - GND3 WR I WR bus4 RD - No connection5 D7 I/O Data bus 76 D6 I/O Data bus 67 D5 I/O Data bus 58 D4 I/O Data bus 49 D3 I/O Data bus 3

10 D2 I/O Data bus 211 D1 I/O Data bus 112 D0 I/O Data bus 013 GND - GND14 LCS I LCD chip select

CN802 (K2, K3, K5 and K6 models only)

1 V4 - LCD drive power supply2 V3 - LCD drive power supply3 V2 - LCD drive power supply4 V1 - LCD drive power supply5 V0 - LCD drive power supply6 VR - V0 voltage adjustment terminal7 NC - No connection8 NC - No connection9 NC - No connection

10 NC - No connection11 NC - No connection12 NC - No connection

Control unit (X57-7250-XX B/5)

50 DGND - GND

CN613 (K2, K3, K5 and K6 models only)

1 LCS O LCD chip select2 GND - GND3 D0 I/O Data bus 04 D1 I/O Data bus 15 D2 I/O Data bus 26 D3 I/O Data bus 37 D4 I/O Data bus 48 D5 I/O Data bus 59 D6 I/O Data bus 610 D7 I/O Data bus 711 RD - No connection12 WR O WR bus13 GND - GND14 A0 O Address bus 0

Page 64: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

64

TERMINAL FUNCTION

Pin Name I/O FunctionNo.13 Vout - Raising voltage output14 VDD - 3.3V15 NC - No connection16 GND - GND17 GND - GND18 D7 I/O Data bus 719 D6 I/O Data bus 620 D5 I/O Data bus 521 D4 I/O Data bus 422 D3 I/O Data bus 323 D2 I/O Data bus 224 D1 I/O Data bus 125 D0 I/O Data bus 026 E/RD I RD bus27 WR O WR bus28 A0 O Adrress bus 029 LRST O LCD reset output30 LCS O LCD chip select

CN803

1 NC - No connection2 L_MIC I Noise canceler MIC3 MICE - MIC GND4 GND - GND5 CH_A I Rotary switch input 16 CH_B I Rotary switch input 27 CH_C I Rotary switch input 38 CH_D I Rotary switch input 49 36M - 3.6V10 S36M - 3.6V11 33M - 3.3V12 TGL0 I Lever switch input 013 TGL1 I Concentric switch input 114 TGL2 I Concentric switch input 215 BLED - Busy LED control16 TXLED - TX LED control17 ORG O Key scan signal output18 VOL I Volume level input19 L_KEY1 O Key scan signal output20 GND - GND

CN804

1 PF2 O Key output (Side2 Key)2 PF3 O Key output (Side3 Key)3 L_KEY1 I Key input4 L_PTTG I PTT GND5 L_PTT I PTT input6 PF1 O Key output (Side1 Key)

Option board unit (X57-7250-XX D/5)

Pin Name I/O FunctionNo.

CN901

1 OPT1 I Scramble code input 1 (Scrambler board)I Channel busy (ANI board)O Busy (VGS-1)

2 OPT3 I Scramble code input 2 (Scrambler board)O Key (ANI board)O Play (VGS-1)

3 RXD1 O Serial Data output(VGS-1)4 TXD1 I PTT (Scrambler board)

I Serial Data input (VGS-1)5 NC - No connection6 OPT4 I/O Echo PTT (Scrambler board)

I PTT (ANI board)I Enable (VGS-1)

7 NC - No connection8 OPT5 I Scramble code input 4 (Scrambler board)

I Emergency (ANI board)I Reset input(VGS-1)

9 DGND - DGND10 AGND - GND11 NC - No connection12 NC - No connection13 AGND - GND14 5A - 5V15 STON O Side tone output(ANI board)16 DI/ANI O Data output (ANI board)17 TCONT O Speaker mute signal (ANI board)18 MAN DOWN I Man-down input (ANI board)19 INH O MIC mute signal output (ANI board)20 OPT2 I Scrambler control signal input (Scrambler board)

O Emergency signal output (ANI board)21 TXO I MIC signal input (Scrambler board)22 RXEO I Audio signal input (Scrambler board)23 RXEI O Audio signal output (Scrambler board)24 TXI O MIC signal output (Scrambler board)25 C3 I Scramble code input 3 (Scrambler board)26 SB2 I Switched B input

Page 65: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

65

TERMINAL FUNCTION

Universal connector

Pin Name I/O FunctionNo.

Pin Name I/O FunctionNo.CN902

1 36M - 3.6V2 S36M - 3.6V3 GND - GND4 VOL I Volume level input5 33M - 3.3V6 CH_A I Rotary switch input 17 TGL2 I Concentric switch input 28 TGL1 I Concentric switch input 19 C - GND10 CH_B I Rotary switch input 211 CH_D I Rotary switch input 412 CH_C I Rotary switch input 3

CN903

1 GND - GND2 CH_A O Rotary switch output 13 CH_B O Rotary switch output 24 CH_C O Rotary switch output 35 CH_D O Rotary switch output 46 36M - 3.6V7 S36M - 3.6V8 33M - 3.3V9 TGL0 O Lever switch output 010 TGL1 O Concentric switch output 111 TGL2 O Concentric switch output 212 BLED - Busy LED control13 TXLED - TX LED control14 ORG I Key scan signal input15 VOL O Volume Level output16 KIN I Key scan signal input17 GND - GND

1 SSW I EXT/INT speaker switch input2 SP+ O BTL output + for external speaker3 SP− O BTL output − for external speaker4 MSW I EXT/INT MIC switch input5 EMC I External MIC input6 ME - External MIC GND7 PTT I External PTT input8 PF I Programmable function key input9 OPT - No connection10 E - GND11 5M - 5V12 TXD O Serial data output13 RXD I Serial data input14 NC - Not used

Top panel unit (X57-7250-XX C/5)

Page 66: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

66

JIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

R610

R366

R249L304

C405

C410

C423

C262C263

C265

D206

C267

D207

C268

C270 C271

D600

C278

L301

L303

L1

L306

L307

C280

L309

C284

C285

C288

L311

L315

L

L122R152 or

L317

C290

L125

L319

C291

C293

L321L323

L324

L325

L327

R309

R310

R312

R316

R318

CN301

R320

R322

R324

R326

R329

R13

R330

R335

R336

R337

R338

R339

R340R341

R342

C306

R343

C307

C

R150

C309

R349

X300

C312C316

R356

C321

C322

C323

C325

R361

C327

C333C334

C338

C340

C341

C345

C346

C348

C350

C351

C354

C356C357 or

C358

C167

C360D304

D305

CC370

C372

XF300

C374

C378

C379

C380

L214

C382

L216

IC30

4

1 121324

L219

C388

C389

L220 C392

C395

C397

C398CF30

0

C400

C404

C406

C407

R251

C413

C260

C261

C264

D20

4

Q301

123 4

D20

5

C266

Q303

C277

L300

L302

L308

C281

IC20

2

1 346

1 346

C282

IC20

3C2

83

L310

C289

L312

L313

L314

C674

L316

C292

L326

R313

R314

R317

R319 R3

21

R323

R325

C308

R347

R348

C311

C313

C315

C317

C318

C324

C329 C3

30

C332C3

35

C336 C3

37

C339

C342

C344

C347

C349

C352

C355

C361

D30

1

C362

D30

2

C363

D30

6 D30

7

L215

IC30

2 134 6

C383

L600

C385

C386

C387

L221

L222

C390

C391

C396

C399

R374

L318

R328

C366

C367

C368

C401

C402

C403

C409

C411

C412

C414

C415

C418

C420

C421

Q302

Q304 13

4 6

L116

L322

R147

R344

R151

R353

R357

R358

R362

R365

R178

C161

C180

C381

IC30

3 145 8

C393

C394

UN

IV.

MA

IN

S

+

DG S

CF301

J79-0042-29 A/5

TK-5310 PC BOARD

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 A/5)

Ref. No. Adress

IC3 4R

IC202 6B

IC203 6B

IC301 8K

IC302 6E

IC303 8I

IC304 6I

IC308 7K

IC450 7N

IC451 8P

IC452 8N

IC454 7M

IC456 7L

Ref. No. Adress

IC457 4N

IC458 6Q

IC459 8M

IC460 5Q

IC461 6P

IC462 6O

IC463 7P

IC602 3P

IC603 4P

IC604 7Q

IC605 7S

IC606 4Q

IC607 7R

Ref. No. Adress

IC608 5S

IC609 4R

Q106 4K

Q107 5K

Q109 4K

Q300 8L

Q301 6C

Q302 4I

Q303 7H

Q304 7J

Q450 8P

Q451 8P

Q452 7O

Ref. No. Adress

Q453 7N

Q454 8N

Q456 8O

Q460 8Q

Q461 5Q

Q605 7Q

D102 5K

D104 5L

D105 5K

D106 4L

D107 4L

D108 6K

D109 6K

Ref. No. Adress

D110 4L

D111 4L

D112 4L

D115 5K

D204 4B

D205 4C

D206 7B

D207 7B

D301 5D

D302 5D

D304 7D

D305 7D

D306 7D

Ref. No. Adress

D307 7E

D450 8O

D451 8O

D452 8Q

D453 7Q

D454 3M

D455 3O

D600 4H

Page 67: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

67

J K L M N O P Q R S

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Q461

L450

R366

R626

R630

R631

R632

R633R634

R636R637 R638R639

0

R640R642

R643

R454

R648

R455

R649

R456

R458

R459

R650R651

C422

R462

R463

R465

R467

R468

R472 R473

R474

R475

R478

R479

R488

C641

C642

C643

C644

Q10

6

C646

Q107

C453

C648

Q109

C649

C457

R493

R688

R496

C650

C460C461

R691

L102

L103

C463

L104

C464

C467

L108

C468

C661

C470C471

C665

L112

C472

C474 C668C669

C476

L117

C477

C478

L120

C481

L121

L122R152 or

C484

L125

IC60

3

IC60

6

1

1

1 458

1 458

45 8

8916

C497

C498

C499

D450

D451

D453R307

R308

R509

IC450

IC451

IC4521

45

8

1

45

8IC45

4

IC4591

4 5

8

R133

IC4611

34

5

R136

IC46

2

IC4631

1

4 5

45

8

8

R522

R528R530

R148 R531R149

C302

C303

R534

R535

IC3

CD300

R150

R539

C501

C504

C505

C506

R10

C508

C511

C512

C513

R550

R20

R361

R556

R26

C520

C138C139

R560

C524

R561

C527

R370

C140

C141

C529

R566 R567C143

R568

C530

C148 C531

C532

R7

C537R574

C538

C151

C152

R577

R579

C156

C157

C540C541

C542

C543

R586

D104

C164 D107

C167

D108

R590

D110

R595

R596

D115

R66

C179

Q6051

3 4

6

R74

3

L610

C398

L616

L617

L618L619

L620L621

L622L623

L624

L625L626

L627L628

L629

Q452

C418

C420

C421

Q304 1

1

1 1 89163

4 4

4

5

5

8

8

6

L109

L114L1

16

R140

R147

R151

R362

R365

R178

C149

C150

C154

C161

D10

9

C180

1 345

Q30

0

L105

L106

L111

L113L1

15

D45

4

R304

R305

R306 IC45

6

IC457

R132

R134

R135

R138

R524

R525

R526

R529

R146

R533

R537

R538

C502

R542

R545

R546

C510

C517

C137

R368

R372

C142

C145

C160

D10

2D10

5

C165

D10

6

C166

D11

1C171 D

112

C172

IC30

1IC

308

Q46

0

L451

CN60

1

R622

R451

R452

R453

R457

R461

R471

R476

R477

R480

C639

R483

R484

R487

C450

C451

C452

C454

R490

C455

C456

R495

R498R4

99

C654

C465

C466

C469

C473

C479

C675

C483

C485

C486

C488

D45

2

D45

5

R500

R520

R552

R553

C519

R558

C522

C523

R562

C526

R563

C533

R581

R583

R584

R587

R593

L606

L607

Q45

0Q

451

Q45

3

Q454 Q45

6

R450C4

82

R544

R554

R557

R559

CN60

9

R635 R6

41

R644

R652C5

C645

IC60

8

IC60

9

IC46

01 4

58

C509C5

15

C534

R571

C535

C536

R575

R576

R580

R582

R585

L608

L609

R625

R628

R645

R647

R653

R485

IC60

4

IC60

5 134 5

C493

IC607

R508

IC45

8 1

134 5

45 8

R515

R516

R532

C507

R564C5

28

R565

R570

R572

R573

C539

R589

R591

R592

R629

IC60

2 145 8

R597

G

S

D

G

S

D

CF301

+

+

164

1617

1

19 20

2

GDS

D

DS SG G

GD

S

1213

3233

E

4849

MAND

1 101120

124

GD

S

1 2

25 OPT6RXEITXOINHTCONTSTONAGNDAIDGNDUSELNCRXD1OPT1

SB2TXI

RXEOOPT2

MAN DOWNDI/ANI

5AAO

AGNDOPT5OPT4TXD1OPT3

26

1

1011

20

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 A/5)

PC BOARD TK-5310

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Page 68: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

J K L M N O P Q R SIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Q461

L450

R610

R366

R626

R630

R631

R249L304

R632

R633R634

C405

R636R637 R638R639

C410

R640R642

R643

R454

R648

R455

R649

R456

R458

R459

R650R651

C422

C423

R462

R463

R465

R467

R468

R472 R473

R474

R475

R478

R479

R488

C641

C642

C643

C644

Q10

6

C646

Q107

C453

C648

Q109

C649

C262C263

C457

R493

R688

C265

D206

R496

C267

D207

C268

C650

C460C461

R691

L102

L103

C463

C270

L104

C464

C271

C467

L108

C468

D600

C278

C661

L301

L303

C470C471

C665

L112

C472

L306

L307

C280

C474 C668C669

L309

C476

L117

C477

C284

C478

C285

C288

L311

L120

L315

C481

L121

L122R152 or

L317

C484

C290

L125

L319

C291

C293

L321

IC60

3

L323

L324

L325

IC60

6

1

1

1 458

1 458

45 8

8916

L327

C497

C498

C499

D450

D451

D453R307

R308

R309

R310

R312

R509

R316

IC450R318

IC451

IC4521

45

8

1

45

8IC45

4

CN301

R320

IC4591

4 5

8

R322

R324

R326

R133

IC4611

34

5

R329

R136

IC46

2

IC4631

1

4 5

45

8

8

R522

R330

R528

R335

R336

R337

R338

R339

R530

R148 R531R149

C302

C303

R534

R340

R535

R341R342

C306

IC3

R343

C307

CD300

R150

R539

C309

R349

C501X300

C504

C505

C506

C312

R10

C508

C316

R356

C511

C512

C513

R550

C321

C322

C323

R20

C325

R361

R556

C327

R26

C520

C138C139

R560

C524

R561

C527

C333

R370

C140

C334

C141

C529

R566 R567C143

R568

C338

C530

C148 C531

C532

R7

C340

C341

C537R574

C538

C151

C345

C152

C346

R577

C348

R579

C156

C157

C540C541

C542

C543

C350

C351

C354

C356

R586

C357 or

C358D104

C164 D107

C167

D108

R590

C360

D110

D304

R595

D305

R596

D115

R66

C179C370

C372

XF300

C374

Q6051

3 4

6

C378

R74

C379

C380

L214

C382

L216

IC30

4

1 121324

L219

C388

C389

L220 C392

L610

C395

C397

C398

L616

L617

L618L619

L620L621

L622L623

L624

L625L626

L627L628

L629

Q452

CF30

0

C400

C404

C406

C407

R251

C413

C260

C261

C264

D20

4

Q301

123 4

D20

5

C266

Q303

C277

L300

L302

L308

C281

IC20

2

1 346

1 346

C282

IC20

3C2

83

L310

C289

L312

L313

L314

C674

L316

C292

L326

R313

R314

R317

R319 R3

21

R323

R325

C308

R347

R348

C311

C313

C315

C317

C318

C324

C329 C3

30

C332C3

35

C336 C3

37

C339

C342

C344

C347

C349

C352

C355

C361

D30

1

C362

D30

2

C363

D30

6 D30

7

L215

IC30

2 134 6

C383

L600

C385

C386

C387

L221

L222

C390

C391

C396

C399

R374

L318

R328

C366

C367

C368

C401

C402

C403

C409

C411

C412

C414

C415

C418

C420

C421

Q302

Q304 1

1

1 1 89163

4 4

4

5

5

8

8

6

L109

L114L1

16

L322

R140

R147

R344

R151

R353

R357

R358

R362

R365

R178

C149

C150

C154

C161

D10

9

C180

C381

IC30

3 1 1 345

45 8

C393

C394

Q30

0

L105

L106

L111

L113L1

15

D45

4

R304

R305

R306 IC45

6

IC457

R132

R134

R135

R138

R524

R525

R526

R529

R146

R533

R537

R538

C502

R542

R545

R546

C510

C517

C137

R368

R372

C142

C145

C160

D10

2D10

5

C165

D10

6

C166

D11

1C171 D

112

C172

IC30

1IC

308

Q46

0

L451

CN60

1

R622

R451

R452

R453

R457

R461

R471

R476

R477

R480

C639

R483

R484

R487

C450

C451

C452

C454

R490

C455

C456

R495

R498R4

99

C654

C465

C466

C469

C473

C479

C675

C483

C485

C486

C488

D45

2

D45

5

R500

R520

R552

R553

C519

R558

C522

C523

R562

C526

R563

C533

R581

R583

R584

R587

R593

L606

L607

Q45

0Q

451

Q45

3

Q454 Q45

6

R450C4

82

R544

R554

R557

R559

CN60

9

R635 R6

41

R644

R652C5

C645

IC60

8

IC60

9

IC46

01 4

58

C509C5

15

C534

R571

C535

C536

R575

R576

R580

R582

R585

L608

L609

R625

R628

R645

R647

R653

R485

IC60

4

IC60

5 134 5

C493

IC607

R508

IC45

8 1

134 5

45 8

R515

R516

R532

C507

R564C5

28

R565

R570

R572

R573

C539

R589

R591

R592

R629

IC60

2 145 8

R597

UN

IV.

MA

IN

S

+

DG S

G

S

D

G

S

D

CF301

+

+

164

1617

1

19 20

2

GDS

D

DS SG G

GD

S

1213

3233

E

4849

MAND

1 101120

124

GD

S

1 2

25 OPT6RXEITXOINHTCONTSTONAGNDAIDGNDUSELNCRXD1OPT1

SB2TXI

RXEOOPT2

MAN DOWNDI/ANI

5AAO

AGNDOPT5OPT4TXD1OPT3

26

1

1011

20

J79-0042-29 A/5

TK-5310 PC BOARD

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 A/5)

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 A/5)

PC BOARD TK-5310

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Ref. No. Adress

IC3 4R

IC202 6B

IC203 6B

IC301 8K

IC302 6E

IC303 8I

IC304 6I

IC308 7K

IC450 7N

IC451 8P

IC452 8N

IC454 7M

IC456 7L

Ref. No. Adress

IC457 4N

IC458 6Q

IC459 8M

IC460 5Q

IC461 6P

IC462 6O

IC463 7P

IC602 3P

IC603 4P

IC604 7Q

IC605 7S

IC606 4Q

IC607 7R

Ref. No. Adress

IC608 5S

IC609 4R

Q106 4K

Q107 5K

Q109 4K

Q300 8L

Q301 6C

Q302 4I

Q303 7H

Q304 7J

Q450 8P

Q451 8P

Q452 7O

Ref. No. Adress

Q453 7N

Q454 8N

Q456 8O

Q460 8Q

Q461 5Q

Q605 7Q

D102 5K

D104 5L

D105 5K

D106 4L

D107 4L

D108 6K

D109 6K

Ref. No. Adress

D110 4L

D111 4L

D112 4L

D115 5K

D204 4B

D205 4C

D206 7B

D207 7B

D301 5D

D302 5D

D304 7D

D305 7D

D306 7D

Ref. No. Adress

D307 7E

D450 8O

D451 8O

D452 8Q

D453 7Q

D454 3M

D455 3O

D600 4H

66 67

Page 69: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

68

JIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

J79-0042-29 A/5

C20

C23

R665

D1

CP13

CP14

L11

IC6IC

71 3

45

R28

R52

R53

R56

R57

Q606

1 346CP

1CP

2

R55

R658

R470

C2C3

R684

C462L1

L3

R11

R12

R13

R14

R15 R1

6R17

R18

R19

R21

R5

R8R9

L613

X1

C10

C11

C12C1

3

C14

IC2

R657

R464

R659

R466

R469

R661

R663

R664

R666R6

76R6

77R6

78R6

79

C458

C664

L611

L612

L614

C28

R604

C32

C34

C35

C607

C609

C614

C615

Q101 13

4 6

R119

R127

R130

R518

L12

C103

C106

IC8

C127

C132

R72

R73

R75

R76

R77

L615

R608

R609

C8

R481

R482

R489

R491

R492

R494

R109

R503

R505

R506

C102

C105

C300

C116

R176

R54

CP10

0CP

101 L123

L126

R110

R121

R125

R129

R131

C101

C108

C110

R153

C125

C129

C136

C173

C175

C177

L118

L124

R143

C128 C1

58

C159C1

63

C169

C170

C191

L119

R106

R114

R116

R120

R145

R155

R158

C122

R160

C126

R162

R166R1

73

C153

C155

C174

C176

C178

C183

C186

R163

D11

7

C189

R601

R602

C408

C603

C604

33M

33A

C22

C24

C25C26

L452

C27C29

C30

C33

R607

C38

CN612

CN613

C608

R460

C1C6

R672

C7

R673R674R675

Q1021

3 4

6

Q103

R680R681R682

R685R686

C459

Q110 Q111

C651C653

X450

L100R690

C657C660

C475 C480

L127

C487

C496

IC610

R101

R105

CP10

R300

CP11

R301

CP12

R302

R303

CP15

R111

CP16

R112

R113

R115

R117

R118

R502

R507

L2 R122

R123

L4

R124

L5L6

L7

IC453

L8

R128

R510

L9

IC4551

1

4

4

5

5

8

8

R511R512 R517

R519

L10

L13

R141

R142

C107X100

IC11

1

34

6

1

34

6

2 3

4

C111

IC4

1

1

56

10

2 3

4

C114

IC5

C115

C117

C118

R156

R157

R159

R165

R167

C130

C131

R22R23

R24C135

R27

R174

R29

R175

R31

R32

R33

R34

R35

R3

R38R39

R40R41R42R43

R44R45R46R47 R48

R49R50

R51

C162

R59

R62 R63

D113

D114

D116

R67R69

D119

Q600

Q601

Q603

Q604

1

3 4

6

IC100

1

3 4

5

R70

IC101

R71

C182

C185

IC300

C190

CP3

CP4 CP5

CP6 CP7

CP8

CP9

Q455

C15

Q457

C17C18

CLKC

32kout

Q459

C19

9697

114A

OG

ND

WR

RD

D7

D6

D5

D4

D3

D2

D1

D0

GN

DLC

S

1128

3233

6465

DSG

DSG

DS

G

1G

ND

MIC

SP

+S

P+

SP

–S

P–

AF

VO

LC

LK

GN

DK

INE

XA

FC

KE

SD

AT

TG

L0

TG

L2

TG

L1

CH

AC

H B

CH

CC

H D

PT

T3

6M

DO

ED

GN

D

GN

DM

ICE

PW

R1

5V

SB

1+

B+

B+

B+

BL

RS

T2

8M

PS

WIN

AP

CE

XS

W3

3M

33

M3

3A

33

A2

5D

15

D1

5D

5M

5M

LC

DV

DG

ND

2 5049

15D

25D

5M

DSG

15V

CV

GD

S

1 1

3

3

4

4

5 5

1

5610

11

1516 20

TK-5310 PC BOARD

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 A/5)

Ref. No. Address

IC1 7I

IC2 7B

IC4 7B

IC5 5C

IC6 4E

IC7 3D

IC8 6F

IC100 4J

IC101 5H

IC200 8P

IC201 7P

IC300 8I

IC305 8K

Ref. No. Address

IC306 8K

IC307 8K

IC453 4G

IC455 4G

IC600 7L

IC601 6K

IC610 8H

Q100 5K

Q101 8H

Q102 6I

Q103 7H

Q104 5K

Q105 4K

Ref. No. Address

Q108 5K

Q110 5J

Q111 5J

Q112 4K

Q200 4L

Q202 4N

Q203 7Q

Q204 5O

Q205 7Q

Q206 7P

Q207 7Q

Q208 7Q

Q209 6R

Ref. No. Address

Q210 4M

Q455 8D

Q457 7D

Q459 4F

Q600 7J

Q601 7J

Q602 6L

Q603 8G

Q604 8G

Q606 5E

D1 4B

D113 5I

D114 4I

Ref. No. Address

D116 6I

D117 5J

D118 6K

D119 3I

D200 4K

D201 7Q

D202 4R

D203 4R

D308 4L

D601 8O

D602 8O

D609 7N

D611 7N

Page 70: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

69

J K L M N O P Q R S

1

2

3

4

5

6

7

8

9

10

11

12

13

14

29 A/5

R153

L1243

C59

C170

R211

C202

C205 R2

64

Q10

4D

200

Q11

2

L119

L128

R106

R114

R116

R139

R144

R145

R155

R158

R160

R162 R1

64

R166

R172

F600

C147

C153

C155

C168

C174

C176

C178

L201

L203

C183

C184

C186

C187 R2

00

R203

R204

R205

R603

R606

C605

C610

C616

R137

C109

R163

R177

F601

1 346

D11

7

Q602

C189

CF30

2

R601

R602

C408

C603

C604

C416

C613

R359

R360

IC30

51 4

58

R212

R219

R225

R228

R617

R618

R231

R232

R236

CN60

6

R244

R245

C219

C232

C622

C624

C625

C627

C629

C632

C635

C638

C252

C640

D60

1

D60

9

IC20

1 1

134 6

45 8

D61

1

R334

L208

L601

L602

L604

R216

R217

R220

R222

R259

123 4

C220

C221

C223

C224

C226

Q20

2

Q210

L2

06

L2

25

L211

R252

R254

R255

C255

C256

C258

C259

D20

2

D20

3

C296

L213

L217

R234

R238 C2

29C2

35

C239

C240

C245

C247

C253

D20

1

Q205

Q20

7Q20

8

L223

+

CF303

R213

R214

R215

R218

R600

R605

CN204

R221

CN205

R223R224R226

R227

R611

R229

R612

R613

R614

R615

R616

R230

R619

R233

R235

R237

R620

R621

R239

C200C201

C203

TH200

R240

C204

R242L227

C206

R243

C207 C209

R246

R247

C210

C215

C216

C218

C602

R256

R258

C606

608

R260

C419

C225

R261

R262

C227

R263

C228

C612

C617

C230

C619

C231

C234C237

C620

C238

C621

C623

C626

C241

C242

C243

C244

C246

C630

C249

C631

C633

C634

C636

C637

C250

C254

C257

Q100

Q105

Q108

R687

Q110 Q111

L107

C273

D602 IC2001

4 5

8

C677

L127

C295

C297

IC600

IC601

1

1

3

3

4

4

5

5

C299R102

R327

R333

142

1

3

1

3

C111

R156

R157

R159

R165

R167 R170

R364

R174

R175

1

3 4

6

C144

162

Q200

Q203

Q204

Q206

Q209

C365

D308

D116

L200

D118

Q600

L204

Q601

00

4

5

L209

C182

C185

L210

C188

L212

L218

C190

IC306

L603

IC3071

4 5

8

1

4 5

8

L605

L228

R201

R202

GD

S

+

G S D

G D

1

14 SSWSP+SP–MSW/CTSEMCMICEPTTREMRTS15MTXDRXDEDSR DS

G

DS G

DS

G

DSG

UN

IV.M

AIN

BPF

BPF GND

TXD

S

2ndLO

PC BOARD TK-5310

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 A/5)

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Page 71: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

J K L M N O P Q R SIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

1

2

3

4

5

6

7

8

9

10

11

12

13

14

J79-0042-29 A/5

C20

C23

R665

D1

CP13

CP14

L11

IC6IC

71 3

45

R28

R52

R53

R56

R57

Q606

1 346CP

1CP

2

R55

R658

R470

C2C3

R684

C462L1

L3

R11

R12

R13

R14

R15 R1

6R17

R18

R19

R21

R5

R8R9

L613

X1

C10

C11

C12C1

3

C14

IC2

R657

R464

R659

R466

R469

R661

R663

R664

R666R6

76R6

77R6

78R6

79

C458

C664

L611

L612

L614

C28

R604

C32

C34

C35

C607

C609

C614

C615

Q101 13

4 6

R119

R127

R130

R518

L12

C103

C106

IC8

C127

C132

R72

R73

R75

R76

R77

L615

R608

R609

C8

R481

R482

R489

R491

R492

R494

R109

R503

R505

R506

C102

C105

C300

C116

R176

R54

CP10

0CP

101 L123

L126

R110

R121

R125

R129

R131

C101

C108

C110

R153

C125

C129

C136

C173

C175

C177

L118

L124

R143

C128 C1

58

C159C1

63

C169

C170

C191

R211

C202

C205 R2

64

Q10

4D

200

Q11

2

L119

L128

R106

R114

R116

R120

R139

R144

R145

R155

R158

C122

R160

C126

R162 R1

64

R166

R172

R173

F600

C147

C153

C155

C168

C174

C176

C178

L201

L203

C183

C184

C186

C187 R2

00

R203

R204

R205

R603

R606

C605

C610

C616

R137

C109

R163

R177

F601

1 346

D11

7

Q602

C189

CF30

2

R601

R602

C408

C603

C604

C416

C613

R359

R360

IC30

51 4

58

R212

R219

R225

R228

R617

R618

R231

R232

R236

CN60

6

R244

R245

C219

C232

C622

C624

C625

C627

C629

C632

C635

C638

C252

C640

D60

1

D60

9

IC20

1 1

134 6

45 8

D61

1

R334

L208

L601

L602

L604

R216

R217

R220

R222

R259

123 4

C220

C221

C223

C224

C226

Q20

2

Q210

L2

06

L2

25

L211

R252

R254

R255

C255

C256

C258

C259

D20

2

D20

3

C296

L213

L217

R234

R238 C2

29C2

35

C239

C240

C245

C247

C253

D20

1

Q205

Q20

7Q20

8

L223

33M

33A

+

C22

C24

C25C26

L452

CF303

C27

R213

R214

R215

C29

R218

R600

C30

R605

C33

R607

CN204

R221

CN205

R223

C38

R224R226

R227

R611

R229

R612

R613

R614

R615

R616

R230

R619

R233

R235

R237

R620

R621

R239

C200C201

C203

TH200

R240

C204

R242L227

C206

R243

C207 C209

R246

CN612

R247

CN613

C210

C215

C216

C218

C602

R256

R258

C606

C608

R260

C419

C225

R261

R262

C227

R263

C228

C612

C617

R460

C230

C619

C231

C234C237

C620

C238

C621

C623

C626

C241

C242

C243

C244

C246

C630

C249

C1

C631

C633

C634

C6

C636

R672

C7

R673

C637

C250

R674R675

C254

C257

Q100

Q1021

3 4

6

Q103

R680

Q105

R681R682

Q108R685R686

R687

C459

Q110 Q111

C651C653

X450

L100R690

C657

L107

C273

C660

D602 IC2001

4 5

8

C475 C480

C677

L127

C487

C295

C297

IC600

IC601

1

1

3

3

4

4

5

5

C299

C496

IC610

R101

R102

R105

CP10

R300

CP11

R301

CP12

R302

R303

CP15

R111

CP16

R112

R113

R115

R117

R118

R502

R507

L2 R122

R123

L4

R124

L5L6

L7

IC453

L8

R128

R510

L9

IC4551

1

4

4

5

5

8

8

R511R512 R517

R519

R327

L10

L13

R333

R141

R142

C107X100

IC11

1

34

6

1

34

6

2 3

4

C111

IC4

1

1

56

10

2 3

4

C114

IC5

C115

C117

C118

R156

R157

R159

R165

R167

C130

C131

R22R23

R24

R170

R364

C135

R27

R174

R29

R175

1

3 4

6

R31

R32

R33

C144

R34

R35

R3

R38R39

R40R41R42R43

R44R45R46R47 R48

R49R50

R51

C162

Q200

Q203

Q204

R59

Q206

Q209

C365

R62 R63

D113

D308D114

D116

R67

L200

D118

R69

D119

Q600

L204

Q601

Q603

Q604

1

3 4

6

IC100

1

3 4

5

R70

IC101

R71

L209

C182

C185

L210

C188

L212

IC300

L218

C190

IC306

L603

IC3071

4 5

8

1

4 5

8

L605

L228

CP3

CP4 CP5

CP6 CP7

CP8

CP9

Q455

C15

R201

R202

Q457

C17C18

CLKC

32kout

Q459

C19

9697

114A

OG

ND

WR

RD

D7

D6

D5

D4

D3

D2

D1

D0

GN

DLC

S

1128

3233

6465

DSG

DSG

DS

G

1G

ND

MIC

SP

+S

P+

SP

–S

P–

AF

VO

LC

LK

GN

DK

INE

XA

FC

KE

SD

AT

TG

L0

TG

L2

TG

L1

CH

AC

H B

CH

CC

H D

PT

T3

6M

DO

ED

GN

D

GN

DM

ICE

PW

R1

5V

SB

1+

B+

B+

B+

BL

RS

T2

8M

PS

WIN

AP

CE

XS

W3

3M

33

M3

3A

33

A2

5D

15

D1

5D

5M

5M

LC

DV

DG

ND

2 5049

15D

25D

5M

DSG

15V

CV

GD

S

1 1

3

3

4

4

5 5

1

5610

11

1516 20

GD

S

+

G S D

G D

1

14 SSWSP+SP–MSW/CTSEMCMICEPTTREMRTS15MTXDRXDEDSR DS

G

DS G

DS

G

DSG

UN

IV.M

AIN

BPF

BPF GND

TXD

S

2ndLO

TK-5310 PC BOARD PC BOARD TK-5310

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 A/5)

TX-RX UNIT (X57-7250-XX) (A/5) : TX-RX section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 A/5)

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Ref. No. Address

IC1 7I

IC2 7B

IC4 7B

IC5 5C

IC6 4E

IC7 3D

IC8 6F

IC100 4J

IC101 5H

IC200 8P

IC201 7P

IC300 8I

IC305 8K

Ref. No. Address

IC306 8K

IC307 8K

IC453 4G

IC455 4G

IC600 7L

IC601 6K

IC610 8H

Q100 5K

Q101 8H

Q102 6I

Q103 7H

Q104 5K

Q105 4K

Ref. No. Address

Q108 5K

Q110 5J

Q111 5J

Q112 4K

Q200 4L

Q202 4N

Q203 7Q

Q204 5O

Q205 7Q

Q206 7P

Q207 7Q

Q208 7Q

Q209 6R

Ref. No. Address

Q210 4M

Q455 8D

Q457 7D

Q459 4F

Q600 7J

Q601 7J

Q602 6L

Q603 8G

Q604 8G

Q606 5E

D1 4B

D113 5I

D114 4I

Ref. No. Address

D116 6I

D117 5J

D118 6K

D119 3I

D200 4K

D201 7Q

D202 4R

D203 4R

D308 4L

D601 8O

D602 8O

D609 7N

D611 7N

68 69

Page 72: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

70

JIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

S901

S902D901

R825

R831

R832

R833

D80

0D

801

D81

0D

811

D81

2

CN713

J79-0042-29 B/5

J79-0042-29 C/5

16IN

T M

IC–

INT

MIC

+IN

T S

P+

INT

SP

+IN

T S

P–

INT

SP

S800A

S805B

S810C

S815D

S8113

S8062

S8011

TK-5310 PC BOARDTX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (C/5) : Top section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 C/5)

Ref. No. Address

D901 13B

Page 73: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

71

J K L M N O P Q R S

1

2

3

4

5

6

7

8

9

10

11

12

13

14

CN923

R825

R826

R829

R830

D80

2D

803

D80

6

D80

7

D80

8D

809

J79-0042-29 E/5

J79-0042-29D/5

1O

PT1

RXD

1N

CN

CD

GN

DN

CA

GN

D2

STO

NTC

ON

TIN

HTX

ORX

EIC3

OPT

3TX

D1

OPT

4O

PT5

AG

ND

1N

C 5A DI

MAN

DOW

NO

PT2

RXEO TX

ISB

2 2625

TXD1

RXD1

S8024

S8139

S8088

S8037

S804*

S8090

S814#

S8113

S8062

S8011

S8126

S8075

PC BOARD TK-5310TX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (E/5)

: ANT section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Component side view

(J79-0042-29 E/5)

TX-RX UNIT (X57-7250-XX) (D/5)

: Option section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Component side view

(J79-0042-29 D/5)

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Ref. No. Address

D800 7I

D801 4I

D802 6K

D803 4K

D806 6M

D807 4M

D808 6L

D809 4L

D810 7G

D811 4G

D812 5G

Page 74: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

J K L M N O P Q R SIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

1

2

3

4

5

6

7

8

9

10

11

12

13

14

S901

S902D901

CN923

R825

R826

R829

R830

R831

R832

R833

D80

0D

801

D80

2D

803

D80

6

D80

7

D80

8D

809

D81

0D

811

D81

2

CN713

J79-0042-29 B/5

J79-0042-29 C/5

J79-0042-29 E/5

J79-0042-29D/5

1O

PT1

RXD

1N

CN

CD

GN

DN

CA

GN

D2

STO

NTC

ON

TIN

HTX

ORX

EIC3

OPT

3TX

D1

OPT

4O

PT5

AG

ND

1N

C 5A DI

MAN

DOW

NO

PT2

RXEO TX

ISB

2 2625

TXD1

RXD1

16IN

T M

IC–

INT

MIC

+IN

T S

P+

INT

SP

+IN

T S

P–

INT

SP

S8024

S8139

S8088

S8037

S804*

S8090

S814#

S800A

S805B

S810C

S815D

S8113

S8062

S8011

S8126

S8075

TK-5310 PC BOARD PC BOARD TK-5310TX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (C/5) : Top section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Component side view (J79-0042-29 C/5)

TX-RX UNIT (X57-7250-XX) (E/5)

: ANT section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Component side view

(J79-0042-29 E/5)

TX-RX UNIT (X57-7250-XX) (D/5)

: Option section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Component side view

(J79-0042-29 D/5)

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Ref. No. Address

D800 7I

D801 4I

D802 6K

D803 4K

D806 6M

D807 4M

D808 6L

D809 4L

D810 7G

D811 4G

D812 5G

Ref. No. Address

D901 13B

70 71

Page 75: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

72

JIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

R801

R804

R805

R807

R808

R809

R810

R811 R812

R813

R814

R815

R816

R817

R818R8

19

R820

R821

R822

R836

R839

R840

R841

R842

R843

R845

R847

C814

R852

R859

R860

C827

C834

C835

C842

Q70

0

Q709

1 345

D80

4

D80

5

Q713 13

4 6

L700

L705

L706

D81

3

L707

D81

4

D81

5

D81

6

D81

7

D81

8

IC801IC802IC803

1

89

16 1

89

16 1

89

16

R701

R709

R711

R713

R718

R707

R714

R719

R721

R729

R733

R735

R738

C702

C704

R742

C707

R744

C709

R745

R746

R753 C7

17

C719

R758 R7

59

C724

C725

C726

C727

R768

C732

C734

R771

R773

C738

R775

C739

C741

R790

C755

C759

R796

R798

D70

0

C761

D70

5Q

801

D70

6C7

67

D70

8

D71

0

C770

D71

1

C772

C774

C776

L801

L805

IC70

1

IC703

1

56

10

IC70

51 4

58

1 458

IC70

6

IC70

7

C788

IC70

8

IC71

0

1 345

IC71

1

IC71

2

134 5

IC71

3

1 458

123 4

1 345 1 3

45

1 345

+

1A

OG

ND

WR

NC

D7

D6

D5

D4

D3

D2

D1

D0

GN

DLC

S14

G SD

B C E

B

C

E

1G

ND

MIC

SP

+S

P+

SP

–S

P–

AF

VO

LC

LK

GN

DK

INE

XA

FC

KE

SD

AT

TG

L0

TG

L2

TG

L1

CH

AC

H B

CH

CC

H D

PT

T3

6M

DO

ED

GN

D

GN

DM

ICE

PW

R1

5V

SB

1+

B+

B+

B+

BL

RS

T2

8M

PS

WIN

AF

CE

XS

W3

3M

33

M3

3A

33

A2

5D

15

D1

5D

5M

5M

LC

DV

DG

ND

2

4950

J79-0042-29 B/5

1

12

1112

21617

GN

D

VO

L

TXLE

D

TGL2

TGL0

S36

M

CH

D

CH

B

GN

D CH

D C

TGL2

33M

GN

D

36M

KIN

OR

G

BLE

D

TGL1

33M

36M

CH

C

CH

A

CH

C

CH

B

TGL1

CH

A

VO

L

S36

M

J79-0042-29 C/5

CN800

R835

R849

R850R851

C826C829C840

Q701

Q702

Q710

1

34

6Q711

1

34

5

R702

R705

R706

R708R710

CN700

C700

R748

R754

R762

R770

R772

R774

C740

C742

C743

C745

C746

C747

C748

C749C750

C752

C753

C754C757 R797

C760C762

C763

D704

Q800C764

C765 D707

C768

C769

C771

C773

C775

C777

C778

C779

L803

C790

C751 C766

L807IC709

1 1

23

5

3 4

5

C828

Q7121

3

6

4

C744D703

R855

Q8031

34

6

1

34

6Q804

IC704

1

34

5

C795

Q703Q704

Q705Q706

Q708

L701

L702

IC800

1

3 4

5

R728

R731R732

R734

R737

C701

C703

R743

C713

C728

C730

C731 C736

D702

Q802L804

R806

C808

R726

R739 R741

R747

C737

CN902

CN903

GS

DGS

DG

SD

G

SD

GS

D

GS

D

TK-5310 PC BOARDTX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6 Foil side view

(J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (C/5) : Top section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Foil side view

(J79-0042-29 C/5)

Page 76: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

73

J K L M N O P Q R S

1

2

3

4

5

6

7

8

9

10

11

12

13

14

R823

C803

C805

R841

R843

C807

R844

R845

R846

R853

C830

C831

C832

C833

C834

C835

C836

C837

C838

C841

34

L703

L704

L708

L709

R713

R718

R707

R714

CN70

2

R721

R722

R723

R735

R742

C708

C709

C716

C725

C729

C738

C739

D70

0

L805

C783

C784

+

1P

F2

PF3

L K

EY

1L P

TT

GL P

TT

PF1

6

1N

CL M

ICM

ICE

GN

DC

H A

CH

BC

H C

CH

D36M

S36M

33M

TG

L0

TG

L1

TG

L2

BLE

DT

XLE

DO

RG

VO

LL K

EY

GN

D20

130LC

SLR

ST

AO

WR

33M

D0

D1

D2

D3

D4

D5

D6

D7

GN

DG

ND

NC

33M

TXO

RX

EO

RX

EI

TXI

C3

SB

2

OPT

1

OPT

2

DG

ND

AG

ND

5A

STO

N

DI

TCN

T

MD

WN

INH

OPT

5

OPT

4

OPT

3

AG

ND

J79-0042-29 D/5

J79-0042-29E/5

R854

R730

R784

D701

Q8031

34

6

1

34

6Q804

IC704

1

34

5

C795

CN802

CN803

R824R827

R828C809

R848

C810

C811

C812

C825

Q703704

Q705Q706

6

2

L800L802

CN804

C800

C801

C802

R856

R857

R858

R720

C712

C718IC

702

156 10

C785

CN941

GS

DG

SD

G

SD

GS

D

PC BOARD TK-5310TX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6 Foil side view

(J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (E/5)

: ANT section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 E/5)

TX-RX UNIT (X57-7250-XX) (D/5)

: Option section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 D/5)

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Ref. No. Address

IC701 4I

IC702 4M

IC703 5I

IC704 7J

IC705 3H

IC706 4B

IC707 5C

IC708 4C

IC709 5E

IC710 6C

IC711 5D

IC712 6F

IC713 7E

IC800 2H

IC801 8H

IC802 8G

IC803 8F

Q700 5F

Ref. No. Address

Q701 5F

Q702 5G

Q703 4J

Q704 4J

Q705 4J

Q706 4J

Q708 4I

Q709 4I

Q710 7C

Q711 7D

Q712 5D

Q713 6C

Q800 6E

Q801 6E

Q802 6I

Q803 6J

Q804 7J

D700 4J

Ref. No. Address

D701 8K

D702 3I

D703 6C

D704 7C

D705 4E

D706 4E

D707 4G

D708 4H

D710 5I

D711 4I

D804 7I

D805 8I

D813 7H

D814 7H

D815 6F

D816 7G

D817 7G

D818 7F

Page 77: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

J K L M N O P Q R SIHGFEDCBA

1

2

3

4

5

6

7

8

9

10

11

12

13

14

1

2

3

4

5

6

7

8

9

10

11

12

13

14

R801

R804

R805

R807

R808

R809

R810

R811 R8

12

R813

R814

R815

R816

R817

R818R8

19

R820

R821

R822

R823

R836

R839

C803

R840

C805

R841

R842

R843

C807

R844

R845

R846

R847

C814

R852

R853R8

59

R860

C827

C830

C831

C832

C833

C834

C835

C836

C837

C838

C841

C842

Q70

0

Q709

1 345

D80

4

D80

5

Q713 13

4 6

L700

L703

L704

L705

L706

D81

3

L707

D81

4

L708

L709D

815

D81

6

D81

7

D81

8

IC801IC802IC803

1

89

16 1

89

16 1

89

16

R701

R709

R711

R713

R718

R707

R714

R719

CN70

2

R721

R722

R723

R729

R733

R735

R738

C702

C704

R742

C707

C708

R744

C709

R745

R746

C716

R753 C7

17

C719

R758 R7

59

C724

C725

C726

C727

C729

R768

C732

C734

R771

R773

C738

R775

C739

C741

R790

C755

C759

R796

R798

D70

0

C761

D70

5Q

801

D70

6C7

67

D70

8

D71

0

C770

D71

1

C772

C774

C776

L801

L805

IC70

1

IC703

1

56

10

C783

C784

IC70

51 4

58

1 458

IC70

6

IC70

7

C788

IC70

8

IC71

0

1 345

IC71

1

IC71

2

134 5

IC71

3

1 458

123 4

1 345 1 3

45

1 345

+

1A

OG

ND

WR

NC

D7

D6

D5

D4

D3

D2

D1

D0

GN

DLC

S14

G SD

B C E

B

C

E

+

1P

F2

PF3

L K

EY

1L P

TT

GL P

TT

PF1

6

1N

CL M

ICM

ICE

GN

DC

H A

CH

BC

H C

CH

D36M

S36M

33M

TG

L0

TG

L1

TG

L2

BLE

DT

XLE

DO

RG

VO

LL K

EY

GN

D20

130LC

SLR

ST

AO

WR

33M

D0

D1

D2

D3

D4

D5

D6

D7

GN

DG

ND

NC

33M

1G

ND

MIC

SP

+S

P+

SP

–S

P–

AF

VO

LC

LK

GN

DK

INE

XA

FC

KE

SD

AT

TG

L0

TG

L2

TG

L1

CH

AC

H B

CH

CC

H D

PT

T3

6M

DO

ED

GN

D

GN

DM

ICE

PW

R1

5V

SB

1+

B+

B+

B+

BL

RS

T2

8M

PS

WIN

AF

CE

XS

W3

3M

33

M3

3A

33

A2

5D

15

D1

5D

5M

5M

LC

DV

DG

ND

2

4950

J79-0042-29 B/5

1

12

1112

21617

GN

D

VO

L

TXLE

D

TGL2

TGL0

S36

M

CH

D

CH

B

GN

D CH

D C

TGL2

33M

GN

D

36M

KIN

OR

G

BLE

D

TGL1

33M

36M

CH

C

CH

A

CH

C

CH

B

TGL1

CH

A

VO

L

S36

M

J79-0042-29 C/5

TXO

RX

EO

RX

EI

TXI

C3

SB

2

OPT

1

OPT

2

DG

ND

AG

ND

5A

STO

N

DI

TCN

T

MD

WN

INH

OPT

5

OPT

4

OPT

3

AG

ND

J79-0042-29 D/5

J79-0042-29E/5

CN800

R835

R849

R850R851

C826C829C840

Q701

Q702

Q710

1

34

6Q711

1

34

5

R702

R705

R706

R708R710

CN700

C700

R748

R754

R762

R770

R772

R774

C740

C742

C743

C745

C746

C747

C748

C749C750

C752

C753

C754C757 R797

C760C762

C763

D704

Q800C764

C765 D707

C768

C769

C771

C773

C775

C777

C778

C779

L803

C790

C751 C766

L807IC709

1 1

23

5

3 4

5

C828

Q7121

3

6

4

C744D703

R855

R854

R730

R784

D701

Q8031

34

6

1

34

6Q804

IC704

1

34

5

C795

CN802

CN803

R824R827

R828C809

R848

C810

C811

C812

C825

Q703Q704

Q705Q706

Q708

L701

L702

IC800

1

3 4

5

R728

R731R732

R734

R737

C701

C703

R743

C713

C728

C730

C731 C736

D702

Q802

L800L802

L804

R806

C808

R726

R739 R741

R747

C737

CN804

C800

C801

C802

R856

R857

R858

R720

C712

C718

IC70

2

156 10

C785

CN902

CN903CN941

GS

DGS

DG

SD

G

SD

GS

D

GS

D

TK-5310 PC BOARD PC BOARD TK-5310TX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6 Foil side view

(J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (B/5) : Control section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6 Foil side view

(J79-0042-29 B/5)

TX-RX UNIT (X57-7250-XX) (C/5) : Top section

-10 : K -11 : K2 -12 : K3 -13 : K4 -14 : K5 -15 : K6

Foil side view

(J79-0042-29 C/5)

TX-RX UNIT (X57-7250-XX) (E/5)

: ANT section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 E/5)

TX-RX UNIT (X57-7250-XX) (D/5)

: Option section

-10 : K -11 : K2 -12 : K3

-13 : K4 -14 : K5 -15 : K6

Foil side view (J79-0042-29 D/5)

Component side

Foil side

Layer 1Layer 2Layer 3Layer 4Layer 5Layer 6

Ref. No. Address

IC701 4I

IC702 4M

IC703 5I

IC704 7J

IC705 3H

IC706 4B

IC707 5C

IC708 4C

IC709 5E

IC710 6C

IC711 5D

IC712 6F

IC713 7E

IC800 2H

IC801 8H

IC802 8G

IC803 8F

Q700 5F

Ref. No. Address

Q701 5F

Q702 5G

Q703 4J

Q704 4J

Q705 4J

Q706 4J

Q708 4I

Q709 4I

Q710 7C

Q711 7D

Q712 5D

Q713 6C

Q800 6E

Q801 6E

Q802 6I

Q803 6J

Q804 7J

D700 4J

Ref. No. Address

D701 8K

D702 3I

D703 6C

D704 7C

D705 4E

D706 4E

D707 4G

D708 4H

D710 5I

D711 4I

D804 7I

D805 8I

D813 7H

D814 7H

D815 6F

D816 7G

D817 7G

D818 7F

72 73

Page 78: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

74

TK-5310 SCHEMATIC DIAGRAM

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

R43

100

R57470k

33M(Y)

C3

0.1u

R26

10k

CP

13

47k

C17

0.1u

D1

MA2S111-F

L5

F6003.15A

IC5

30625MGP346HU

1BATTDET

2NC(ANEX0)

3ASSIST

4 VoICE5

SoE6

UL7

DAT8

CLK9

SDA10

BYTE11

CNVSS12

STRB13

NC14

RESET15

XoUT16

VSS117

XIN18

VCC119

NMI20

RTCDT21

PSW22

INTRA23

LD24

BEEP25

LE26 BSFT27

KEY/PLAY28

LCDV29

INH30

AUXI31

TCNT32 BEEPS

33T

XD

134

VC

C1

35R

XD

136

VS

S2

37B

US

Y38

RT

SM

/EX

To39

TX

DM

40R

XD

M41

DS

RM

42C

TS

M43

A20

44K

ES

45K

IN46

MoD

EL

47R

DY

48A

LE49

HoL

D50

HLD

A51

WN

52V

N53

EX

TIM

54S

CS

W55

BC

LK56

RD

57B

HE

58W

R59

TG

L060

TG

L161

TG

L262

CS

363

CS

264

CS

1

65CS0

66A19

67A18

68A17

69A16

70A15

71A14

72A13

73A12

74A11

75A10

76A9

77INAFC

78CH_A

79CH_B

80CH_C

81CH_D

82VCC2

83A8

84VSS3

85A7

86A6

87A5

88A4

89A3

90A2

91A1

92A0

93EXAFC

94HINT

95INT3

96PTT

97E

XS

P

98D

RS

T

99F

RS

T

100

NC

101

D7

102

D6

103

D5

104

D4

105

D3

106

D2

107

D1

108

D0

109

5TC

110

5RC

111

5CC

112

AP

CS

W

113

CA

E3

114

VU

115

MM

116

PW

R

117

WPA

118

SQ

119

CV

120

RS

SI

121

TE

MP

122

BAT

T

123

RE

M

124

AV

SS

125

VoL

126

VR

EF

127

AV

CC

128

T/R

R28

47k

R48 0

CP12 100

R29

47k

R610

1k

R40

100

IC3AT2425610TI27

1A0

2A1

3NC

4GND

5SDA

6SCL

7WP

8VCC

C8

470p

R42

100

R7

47k

R31

470k

C7

470p

R38

470

C10

0.1u

R3

47k

C5

0.1u

R27 1k

R52

100k

C11

0.1u

L6

C14

0.01u

CP5 100

CAE3

R10

47k

R8

10k

C1

0.1u

R24

10k

R47

100

R12

470k

R34

470k

GND(Y)

R54 100

R11

470k

C13

47p

CP

15

47K

R19 10

C18

470p

R5

470k

R20

0

R13

470k

CP10 100

R53 100

R32

470k

R9

100k

CP8 100

L1

C6

470p

L3

C19

470p

R21

47k

R46

47k

L2

IC1MM1522XURE

1NC

2GND

4VOUT

3VCC

CP

16

47K

R59

470k

L4

L7

R62

100k

R55

100

R41

100

R68

410

0k

CP

247

0K

R771M

R56 100

R17

120k

CP7 1K

28MB(Y)

R14

470k

R23

100k

(D)

R18 10

R45

100

CP4 100

C15

0.1u

IC4S-80930CNNB-G

1VSS

2VDD

4 oUT

3 CD

L9

R49

100

R51

470k

CP9 100

R39

470

32kout

D60

0

1SR

154-

400

R16

470k

C20

0.1u

C22

0.1u

R69

0

330

CP11 100

CLKC

R44

100

CP6 1K

L600

L10

IC2RV5C386A

132KOUT

2SCL

3SDA

4INTRB

5VSS

6INTRA

7CLKC

8OSCOUT

9OSCIN

10VDD

C2

0.01

u

R15100k

X1L77-1802-05

BATT+B(Y)

CP

14

47k

R63

47k

R22

220k

(D)

CP3 100

L8

CP

147

k

R50

100

C12

470p

IC6

A1

A3

A2

A7

A3

RY

/BY

A4

WE

A5

A9

A6

A13

B1

A4

B2

A17

B3

VP

P

B4

RE

SE

T

B5

A8

B6

A12

C1A2

C2A6

C3A18

C4NC

C5A10

C6A14

D1A1

D2A5

D3NC3

D4A19

D5A11

D6A15

E1

A0

E2

DQ

0

E3

DQ

2

E4

DQ

5

E5

DQ

7

E6

A16

F1

CE

F2

DQ

8

F3

DQ

10

F4

DQ

12

F5

DQ

14

F6

BY

TE

G1oE

G2DQ9

G3DQ11

G4VCC

G5DQ13

G6DQ15/A-1

H1VSS1

H2DQ1

H3DQ3

H4DQ4

H5DQ6

H6VSS2

BEEPS

TCNT

AUXI

INH

KEY_PLAY

LCDV

CLK

BSFT

LE

BEEP

LD

PSW

CPUCLK

RESET28M 33M

STRB

CLK

SDA

UL

oE

DAT

RESET

T/R

TEMP

SDA

CLK

oP_T

XD

1

RX

D1

BU

SY

RT

S

CT

SM

DS

RM

RX

DM

TX

DM

A20

KE

Y1

RD

Y

KE

S

VN

WN

EX

TIM

SC

SW

R

CS1

CS2

LCS

A17

A18

A19

CS0

A14

A15

A16

A11

A12

A13

A10

CHD

CHA

INAFC

A9

CHC

CHB

WR

RD

TG

L0

TG

L1

TG

L2

A8

A4

A3

A2

A1

A0

EXAFC

HINT

A7

A6

A5

PTT

+B

33M SB

33M

TE

MP

RE

M

VoL

RS

SI

PW

R

WPASQ

MM

5CC

D0

D1

D2

D3

D4

D5

D6

D7

AP

CS

W

5TC

5RC

EX

SP

DR

ST

FR

ST

BAT

TD

ET

D1

D6

D3

D4

A0

RD D0

D7

FC

S

A1

D2

D5

A17

A15

A6

A12

A20

A2

A16

A11

A19

A7

A3

C23

0.01

u

IC7TC7S08FU-F

1INB

2INA

3GND

4oUTY

5VCC

L11CS0

FCS

CS2

33M

33M

33M

33A

33M

BATTDET

ASSIST

BEEP

A18

A10

A8

WR

A9

A4

A13

A14

A5

FR

ST

EEPROM

S

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

REVERSECURRENTPREVENTION

D1

RTC IC

VOLTAGE DET

TEMPERATURE DET

CPU

FLASH ROM

CS AND

CPU

POWER

CV

TEMP DET

REVERSECURRENTPREVENTION

7.5V

A B C D E

1

2

3

4

5

6

7

X57-725 1/12

Page 79: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310SCHEMATIC DIAGRAM

D

D

D

DD D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

DD

D

POWER

C62

110

0p

R67

47k

R70

47k

D60

1

AV

RM

1005

C27

0M

L602

L607

C62

2

100p

C63

9

0.1u

33A(Y)

C63

1

470p

R76 47k

C624 100p

C63

010

0p

C63

4

470p

C63

6

470p

C28

4.7u

C32

0.01

u

C62

7

100p

Q606UM6K1N

R61

3

470

C63

8

470p

D609NNCD6.8G-A

R33

47k

C63

2

100p

R618470

R69

47k

R61

4

1k

IC8

A1

CV

SS

1B

1A

22C

2C

VS

S2

C1

DV

DD

1D

4A

10D

3H

D7

D2

A11

D1

A12

E4

A13

E3

A14

E2

A15

E1

CV

DD

1F

4H

AS

F3

DV

SS

1F

2C

VS

S3

F1

CV

DD

2G

2H

CS

G1

HR

_WG

3R

EA

DY

G4

PS

H1

DS

H2

ISH

3R

_WH

4M

ST

RB

J1Io

ST

RB

J2M

SC

J3X

FJ4

HoL

DA

K1

IAQ

K2

HoL

DK

3B

IoL1

MP

_MC

L2D

VD

D2

L3C

VS

S4

M1

BD

R1

M2

BF

SR

1 N1CVSS6

N2BCLKR1

M3HCNTL0

N3DVSS5

K4BCLKR0

L4BCLKR2

M4BFSR0

N4BFSR2

K5BDR0

L5HCNTL1

M5BDR2

N5BCLKX0

K6BCLKX2

L6CVSS7

M6HINT

N6CVDD4

M7BFSX0

N7BFSX2

L7HRDY

K7DVDD4

N8DVSS6

M8HD0

L8BDX0

K8BDX2

N9IACK

M9HBIL

L9NMI

K9INT0

N10INT1

M10INT2

L10INT3

N11CVDD5

M11HD1

L11

CVSS8

N12

BCLKX1

M12

DVSS7

N13

BFSX1

M13

BD

X1

L12

DV

DD

3

L13

DV

SS

2

K10

CLK

MD

1

K11

CLK

MD

2

K12

CLK

MD

3

K13

HP

I16

J10

HD

2

J11

ToU

T

J12

EM

U0

J13

EM

U1_

oFF

H10

TD

o

H11

TD

I

H12

TR

ST

H13

TC

K

G12

TM

S

G13

CV

SS

5

G11

CV

DD

3

G10

HP

IEN

A

F13

DV

SS

3

F12

CLK

oUT

F11

HD

3

F10

X1

E13

X2_

CLK

IN

E12

RS

E11

D0

E10

D1

D13

D2

D12

D3

D11

D4

C13

D5

C12

A16

C11

DV

SS

4

B13

A17

B12

A18

A13A19A12A20

B11CVSS9

A11DVDD5

D10D6

C10D7

B10D8

A10D9

D9D10

C9D11

B9D12

A9HD4

D8D13

C8D14

B8D15

A8HD5

B7CVDD6

A7CVSS10

C7HDS1

D7DVSS8

A6HDS2

B6DVDD6

C6A0

D6A1

A5A2

B5A3

C5HD6

D5A4

A4A5

B4A6

C4A7

A3A8

B3A9

C3 CVDD7

A2 A21

B2 DVSS9

C33

0.01

u

R619 470k

CPUTXDM(Y)

L606

C25

0.01

u

C24

4.7u

C62

6

470p

RXDM(Y)

R61

6

1k

R620 47k

R72 47k

C30

0.01

u

L604

R61

2

1k

C63

5

100p

R617

470

R62

2

470k

CN606

1 DSR

2 E

3 RXD

4 TXD

5 5M

6 RTS1

7 REM

8 PTT

9 MICE

10 EMC

11 MSW/CTS

12 SP-

13 SP+

14 SSW

R687

0

R686

470k

C61

910

0p

R71

47k

D60

2

AV

RM

1005

C27

0M

L605

R75 47k

R61

1

1k

C34

0.01

u

15D(Y)

C63

7

470p

C350.01u

C64

1

0.1u

C63

3

470p

IC602TC7W53FK(F)

1 CoMMoN

2 INH

3 VEE

4 GND 5A

6CH1

7CH0

8VCC

C62

010

0p

L12

R35

47k

C64

0

470p

R66

100k

C38

0.01u

C29

0.01

u

R73 47k

C26

0.01

u

R621 100k

R74 47k

D611NNCD6.8G-A

R61

5

1k

C27

0.01

u

R685

470k

L13

C62

910

0p

IC603TC74VHCT244AFT

11G

21A1

32Y4

41A2

52Y3

61A3

72Y2

81A4

92Y1

10GND

112A1

121Y4

132A2

141Y3

152A3

161Y2

172A4

181Y1

192G

20VCC

L601

L603

C62

3

100p

C62

533

00p

EM

U0

EM

U1

D6

D5

WR

RD

D4

33A

15D

SRESET

BFSX1

SDTI

LRCK

SCLK

SDTo

LRCK

SCLK

CS

SD

o

BIo

CS

1

A0

D7

CT

S

PT

T

EX

SP

RE

M

RX

D

DS

R

5MC

S

5M

TXDM

DAT

CLK

STRB1

RTS

oE1

LD1

EXTI

CHGIo

oE

DAT1

LD

STRB

CLK1

5M

33M

D_TXD

SCLK1

DS

PC

LK D3

DR

ST

EM

U1

EM

U0

D2

D1

A1

BDX2

D0

BDX1

INT0

RDY

BFSX2

HINT

BDR2

BCLKX2

A2

BCLKR2

BFSR2

A3

SURGEABSORPTION

D601,602

DSP

BUFFER

MULTIPLEXER

POWER

CPU

POWER

CPU

CPU

DSP-FPGA

POWER

MIC

EE

MC

CT

SS

P+

SP

-

CV CV

SW

EMC

1

5M

TXD

SSW

REM

MICE

EXT ANT

MSW/CTS

14DSR

RXD

GND

PTT

UN

IVE

RS

AL

CO

NN

EC

TOR

E

GND

SP-

RTS1

SP+

SURGEABSORPTION

D609,611

F G H I J

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

X57-725 2/12

Page 80: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310 SCHEMATIC DIAGRAM

D

D

D

D

D

D D

D

PO

WE

R

R464

22k

R46

6

1.8k

R52

6

47

C51

0

1u

R46

9

220k

R51

2

470k

C50

2

0.1u

R478

220k

R502

10

C48

2

0.1u

R465

4.7k

L450

R49

0

100k

D450RB706F-40

C457

1u

C45

5

4.7u

R45

7

100k

C51

9

100p

R546

120k

R553

39k

R455

22k

SSM3K15TE(F)Q457

R45

8

1M

R45

0

470k

C461

0.1u

C52

6

100p

SSM3K15TE(F)Q456

C48

7

0.1u

C49

8

1200

p

C49

6

0.1u

R47

2

470k

R471

10

C51

2

150p

IC458TC7W66FK-F

1 IN_oUT1

2 oUT_IN1

3 CoNT2

4 GND 5IN_oUT2

6oUT_IN2

7CoNT1

8VCC

R453

470k

C504

1u

D451RB706F-40

R49

4

10

C47

5

0.01

u

C46

3

1u

R48

1

10k

R452

22k

2SC4617(S)Q460

C45

4

4.7u

C476

1u

R55

2

22k

R451

22k

R492

10

R495

220k

R511

470k

R47

7

1M

C48

1

0.1u

X450L77-1962-05

1 VCoNT

2 GND 3oUTPUT

4VCC

C51

5

4.7u

IC452TC75W51FK(F)

1

2

3

4 5

6

7

8

C488

0.22u

C460

0.1u

R52

047

k

C52

7

0.1u

R454

10k

R470

470k

C45

9

2.2u

L451 C

524

0.1u

R510 470k

SSM3K15TE(F)Q453

R507 10

R54

2

33k

R563

120k

R487

47k

C48

6

1000

p

R50

047

C48

5

1u

IC453TC7WH74FK-F

1CK

2D

3Q

4GND

5Q

6CLR

7PR

8VCC

C474

0.1u

C51

7

2700

p

TC7WU04FK-FIC455

11A

23Y

32A

4GND

52Y

63A

71Y

8VCC

C465

0.1u

C47

3

470p

R47

9

470k

C477

0.1u

R55

6

33k

IC459TC75W51FK(F)

1

2

3

4 5

6

7

8

D453RB706F-40

C50

9

4.7u

C46

6

1u

C47

2

0.1u

2SA1832(GR)FQ451

R488

10k

C505

10u

C50

1

100p

C450

1u

SSM3K15TE(F)Q459

R49

6

4.7k

2SC4738(GR)FQ450

R46

2

33k

R538

47k

R463

2.2k

IC451TC75W51FK(F)

1

2

3

4 5

6

7

8

C48

4

0.1u

R52

2

47k

C46

2

470p

IC454AK4550VTP

1VCoM

2AINR

3AINL

4VSS

5VDD

6DEM0

7DEM1

8SDTo

9

SDTI

10

LRCK

11

MCLK

12

SCLK

13

PWAD

14

PWDA

15

AoUTL

16

AoUTR

R51

847

R56

2

150k

R459

10k

R51

5

0

R506

10

R53

7

33k

IC456TC75W51FK(F)

1

2

3

45

6

7

8

R46

0

470

R48

5

4.7k

R473

0

R50

947

R56

1

33k

C464

0.1u

SSM3K15TE(F)Q452

C46

7

1u

R45

6

150k

C48

3

10u

R51

6

56k

C480

0.01u

R545

47k

C47

0

150p

C46

8

0.1u

C49

3

0.22

u

R50

8

10k

R524

47k

R47

6

470k

R484

47

R49

1

2.7k

R525

180k

R47

4

120k

R49

8

22

C49

7

10u

2SJ347FQ455

2SJ347FQ454

R493

4.7

R564

1M

R48

0

47k

R48

3

10k

R505

10

C45

1

100p

C471

150p

R519

47

C47

8

4.7u

TC7W66FK-FIC450

1 IN_oUT1

2 oUT_IN1

3 CoNT2

4 GND 5IN_oUT2

6oUT_IN2

7CoNT1

8VCC

R468

33k

C47

9

4.7u

R47

5

33k

C458

1u

R48

9

100k

R49

9

3.3k

R48

2

100k

D45

2

MA

2S11

1-F

R46

7

470k

C45

2

100p

R550 1M

R50

3

10

R517

47

L452

C46

9

0.1u

R46

1

390k

C45

6

2.2u

MU

XoU

T

5M

33M

MM

VATS

33A

C453

0.1u

5M

33A

5R SQ

33M

TX

I

SC

SW

T

SC

SW

R

33A

TX

o

5M

BF

SX

1

LRC

KS

DT

I

SD

To

SC

LKM

CLK

BE

EP

S

33A

33A

RX

Eo

SC

SW

R

RX

EI

MC

LK

CPUCLK

BSFT

DSPCLK

Ao

AI_TX

MIC MUTE SW

VGS I/O SW

SW(VGS TX I/O)

EXT MIC SW

BUFFERD-TYPE FLIP FLOP

TX SCRAMBLER SW

REVERSECURRENTPREVENTION

DETECTION

DETECTION

DETECTION

AUTO GAIN CONTROL

Q450,451

NOISE AMP

OP AMP(5V REFERENCE/BUFFER AMP)

CODEC

OP AMP(TX LPF/RX LPF)

BEET SHIFT SW

CPU

POWER

CPU

DS

P-F

PG

A

POWER

DSP-FPGA

CPU

POWER

OPTION

POWER

CPU

EMCMICECTSSP+SP-

SP+

MICE

SP-

CV CV

OPTION

MIC

MIC MUTE

BUFF AMP(MOD)

MIC AMP(with AGC)

IC451

OP AMP(TX AGC AMP/BUFFER AMP)

Q454,456

SW(RX SCRAMBLER SW/BEEP SW)

OP AMP(TX BUFFER AMP/RX BUFFER AMP)

EXT MIC SW

IC452

K L M N O

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

X57-725 3/12

Page 81: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310SCHEMATIC DIAGRAM

E

E

E

EE

E

D

E

D

D

D

E

EE

R572

4.7k

R582

470k

C50

7

0.1u

C530

0.1u

R64

5

100k

R57

3

10

C533

10u6.3

C50

6

0.01

u

R55

747

R55

447

C532

0.1u

C54

1

10u

R58

9

100k

IC463TC75W51FK(F)

1

2

3

4 5

6

7

8

R53

4

100k

R575

470k

IC606BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9

QS

10

Q’S

11

Q8

12

Q7

13

Q6

14

Q5

15

OE

16

VDD

R570

3.3k

C52

9

0.01

u

C53

9

100p

C54

0

0.1u

C50

8

0.01

u

R56

6

10k

R583 47

R59

1

68k

IC457EX128TQ64I630C

1

GND

2

SROUT(0)

3

SROUT(1)

4 TMS5 GND6 VCCI7 SROUT(2)8 SROUT(3)9 SROUT(4)

10 SROUT(5)11 SROUT(6)12 SROUT(7)13 STRB14 GND15

TESTMODE16 DSPCLK

17

IF_I

N

18

RE

SE

T

19

VC

CI

20D

IFF

21S

RO

E22

VC

CA

23G

ND

24F

LRC

K25

SR

CK

226

FS

CLK

27F

MC

LK28

CLK

OU

T29

FS

OU

T30

SO

UT

31S

RIN

32C

PU

CLK 33

GND

34BUFA(0)

35BUFA(1)

36VSV(VCCA)

37VCCI

38BUFA(2)

39BUFY(3)

40BUFA(3)

41BUFA(7)

42CLK

43BUFA(5)

44VPP(VCCA)

45LP/GND

46

GND

47

BUFA(8)

48

SMPLCLK

49B

UF

Y(0

)

50B

UF

Y(1

)

51B

UF

Y(2

)

52V

CC

I

53B

UFA

(4)

54B

UF

Y(4

)

55N

O

56N

O

57V

CC

A

58G

ND

59B

UF

Y(5

)

60B

UF

Y(6

)

61V

CC

I

62B

UF

Y(7

)

63B

UF

Y(8

)

64B

UFA

(6)

IC462M62364FP-F

1VIN1

2VoUT1

3VoUT2

4VIN2

5VDD

6LD

7CLK

8DI

9VIN3

10VoUT3

11VoUT4

12VIN4

13VIN5

14VoUT5

15VoUT6

16VIN6

17D0

18VDAREF

19RESET

20GND

21VIN7

22VoUT7

23VoUT8

24VIN8

R531 1k

C53

5

0.1u

R59

0

1k

R57

6

470k

R584 47

R535

6.8k

R558 100k

R57

4

470k

R585

470k

C528

0.1u

R53

2

820

R530 1k

C513

0.1uC534

0.1u

R59

5

8.2k

C54

3

100p

R58

647

0k

R56

8

10k

Q605UM6K1N

R565

1M

D45

5

1SS

388F

R587

1k

R581 47

C52

0

0.01

u

R53

9

10

C52

2

0.01

u

R528 1k

R533 100k

C5381u C

542

0.1u

C51

1

0.01

u

C536

1u

L610

R529 10k

R59

3

10k

R580

10

R577

47k

R55

947

R579

100k

R567

100k

C531

0.1u

R649

3.9k

D45

4

1SS

388F

C64

6

0.1u

SSM3K15TE(F)Q461

R59

2

1k

C499

0.1u

C5370.1u

R54

4

10

IC460TC7W66FK-F

1 IN_oUT12 oUT_IN1

3 CoNT24

GND5

IN_oUT2

6

oUT_IN2

7CoNT1

8VCC

R56

0

100k

R64

7

100k

R59

7

100k

R648

3.9k

3.9k

R644

C52

3

0.01

u

R59

6

120k

R571

100k

IC461TC75S51FE(F)

1IN+

2VSS

3IN-

4oUT

5VDD

TU

NE

2

5M5M

CLK

1

LD1

L2S

F

DAT

1

33A VC

TU

NE

AP

C

33A

VA

RS

Ao

AIBE

EP

LRST

ECSW

VATS

5MC

STRB

VARS

CS

SD

o

UN

_DAT

SR

ES

ET

IF_I

N

CLK

SC

LK1

oE

TCoNT

EXTIM

DSR

CTS

EXTI

RXD

oP_INH

BUSY

oPT4

DAT1

CLK1

oPT1

STRB1

oP_MAN

oPT5

oE1

UN_DAT

CHGIo

oPT6

oPT2

oPT3

oPT1

33M 5M

25D

oPT

3

oPT

2

33M

KE

Y_P

LAY

AU

XI

RX

DM

TC

NT

INH

DS

RM

CT

SM

33M

STo

N

5V 3.3VLEVEL CONVERTER

SHIFT REGISTER

FPGA

D/A CONVERTER

CPU

POWER

DSP-FPGA

CPU

OPTION OPTION

POWER

CPU

POWER

MICE

SP+SP- SP-

MICE

SP+

CV

CV

OPTION

OPTION

OPTION

MICMIC

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

CPUCPU

CPU

SW(VGS RX I/O)VGS I/O SW

RX SUMMING AMP

DSP-FPGA

POWER

POWER

CV

OP AMP(TX MOD AMP/3.3V REFERENCE)

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

P Q R S T

X57-725 4/12

Page 82: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310 SCHEMATIC DIAGRAM

RX

RF

C33

3

470p

C30

2

1u

C10

2

47p

IC100LMC7101BIM5

1OUTPUT

2V+

3INPUT+

4INPUT-

5V-

R300

10k

Q102SSM6L05FU

C341*

L309

*

R12

0

10M

C30

0

0.1u

R31

4

100k

C315*

IC601XC6204B502MR

1VIN

2VSS

3CE

4NC

5VoUT

C10

9

1u

L301

39n

C61

3

470p

C14

2

0.47

u35

C11

0

470p

R135

4.7k

L311

*

R302

560k

C60

91u

C32

7

1u

C32

4

470p

R304

10k

R31

9

100k

C336*

C33

4

470p

C10

6

470p

R31

6*

C60

2

470p

R127

6.8k

IC301LMC7101BIM5

1O

UT

PU

T

2V

+

3IN

PU

T+

4IN

PU

T-

5V

-

C34

2*

C60

5

470p

C11

1

1u

R374*

C132

470p

C14

1

470p

R60

947

0k

C30

8

470p

R60

4

470k

C19

1

470p

L307

C33

5*

R60

0

470k

C136

0.01u

C33

2*

R105

47

R106

100

R60

6

470k

C12

5

0.1u

C10

5

47p

C10

7

470p

R303

10k

R31

8

100k

C346*

C32

1

470p

R10

2

47k

C61

0

0.1u

L302

39n

F60

1

0.25

A

R307

270k

R13

4

3.3k

Q101SSM6L05FU

2SC4617(S)Q300

R31

3*

R11

4

180k

C34

0

470p

C60

6

0.1u

IC300LMC7101BIM5

1O

UT

PU

T

2V

+

3IN

PU

T+

4IN

PU

T-

5V

-

R60

2

470k

C12

7

470p

C30

9*

R121

1.2k

C13

1

0.01

u

C13

9

0.01

u

Q600SSM6L05FU

R30

9

1M

2SC4617(S)Q100

R10

1

470k

R301

100k

R10

9

1k

C32

5

470p C35

0

470p

C116

0.01u

X100L77-3013-05

1 VC

2 GND 3oUTPUT

4VCC

R306

100k

SSM3K15TE(F)Q603

R317*

C11

8

470p

Q601SSM6L05FU

R131

1.2k

C306*

D119DA221

C67

7

0.1u

L312

*

C33

8

470p

C60

3

470p

C61

51u

C318

470p

C32

3

470p

15V(Y)

C31

3

470p

IC610TK11250CUCB

1NP

2GND

3CoNT

4VIN

6VoUT

R30

5

47k

R12

2

3.9k

CP101

1K

D11

8M

A2S

111-

F

C33

9*

R31

0

1M

C14

0

0.04

7u35

L306

*

C11

4

0.1u

C307*

R119

1k

D30

5

1SV

286F

C61

4

1u

C10

1

0.1u

C303

0.1u

R60

5

0

C129

0.01u

R112

10

R11

3

470k

R12

9

1.2k

R17

3

10M

3SK318Q301

R177

100k

C31

24p

2SK879(Y)FQ103

IC600XC6204B502PR

1NC

2VSS

3CE

4VIN

5VoUT

R60

347

0k

C31

7*

R60

81M

L303

*

C12

6

0.1u

R31

210

0k

C60

8

10u

R32

0

100k

C11

5

0.1u

C13

5

0.01

u

R12

5

1.2k

R11

0

100k

D30

4

1SV

286F

C31

6*

R60

7

470k

C61

2

470p

IC101ADF4111BCP7

1CPGND

2AGND

3AGND

4RFinB

5RFinA

6A

VD

D

7A

VD

D

8R

EF

in

9D

GN

D

10D

GN

D

11 CE

12 CLK

13 DATA

14 LE

15 MUXoUT

16D

VD

D

17D

VD

D

18V

p

19R

set

20C

P

C12

2

47p

L310

*

CP100

1K

C60

747

0p

D30

7

1SV

286F

C10

3

47p

C61

6

1u

L100

R130

100k

C12

847

p

D30

1

1SV

286F

C11

7

0.01

u

C34

7*

C10

8

0.1u

R60

1

470k

CV

L308*

C32

2

470p

C33

7*

Q602SSM6L05FU

R11

718

k

C330

470p

R308

10k

L300

*

C35

2*

C61

7

1u

TPC6108-FQ604

R11

1

100

D30

6

1SV

286F

C311*

5M(Y)

R11

6

47k

D30

2

1SV

286F

R32

1

100k

R176

0

R11

5

10

C34

5

470p

C60

4

470p

C34

4*

C32

9

470p

R11

83.

3k

ASSIST

PWR

+B

SB

15V

5MCS

S33A5M

VC

LE

DATCLK

5C

S33A

UL

MUXoUT

S33A

5R

5CC

33A

5T

5MC

5CC

PWR

5TC

5RC

TUNE

15V

TUNE2

5C

VCXO

VARI-CAPTUNE

D301,302

RIPPLE FILTER

BYPASSDIODE

SW

5T SW

5M SW

RIPPLEFILTER

BUFFER for CV

DC AMP for BPF

DC AMP for VCO TUNE

PLL IC

CPU

POWER

OPTION

CPU

OPTION

POWER

CPU

SP+

MICE

SP- SP-

MICE

SP+

CVCV

MICMIC

TUNE 1

5R

DSP-FPGADSP-FPGA

2V

Tune2_out

22p

47100n

22p

27n

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

C332

18p

7p

C344

12p27n

1p

27p56n 82n

120n

27p47p18p

L310 R316

7p

7p

C341

8p

27 10p

27n

L306 C339C337C335C317

18n

7p

C346

47p

7p

1.5p

39p47n

15p

C336L309

-10,-11,-12

C311

3p

5p4p

12p18n

L311

3p18n 27

C342R374L300 C309R313

15p

C307

15p

K4,K5,K6 12p56 22

C347 C352

120

C316

68k

27n

4p22p

27n

22n

27p

C315

-13,-14,-15 18p

56n

27p

C306L308

18n

R317

22p

L312

12p

L303

9p

47k

K,K2,K3

X57-7250-XX

CPU

LOOPFILTER

DC AMP for BPF

VOLTAGE REGULATOR(5T/5R)

VOLTAGEREGULATOR(5C)

VOLTAGE REGULATOR(5MCS)

5M SW

S33A SW

LNA(LOW NOISE AMP)

5R SW

SB SW

5C VOLTAGE RISE

D304-307

VARI-CAPTUNE

7.5V

3.32V

4.98V

5.0V

7.5V3.32V

R:0VT:3.35V

R:3.32VT:0V

R:4.97VT:0V

R:0VT:4.90V

14.51V 13.75V 7.17V

1.48V

3.3V

3.26V

R:1.90VT:1.68V

1.49V

3.22V

5.0V

14.51V 13.81V

0.53V

1.90V

R:2.38VT:0V

R:0.69VT:0V

R:2.06VT:1.67V

U V W X Y

X57-725 5/12

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

Page 83: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310SCHEMATIC DIAGRAM

C36

8

0.1u

R132

0

L315*

C151*

C170

2p

C15

347

0p

C37

8

12p

C36

6

470p

D11

2

1SV

282-

F

D105

1SV282-F

C176*

C15

2

2.5p

C35

6

6p

C145

470p

C15

6*

D110

1SV325F

C35

1

10p

C15

7*

R33

5

680

C16

2*

C144

10u6.3

C15

5

470p

C15

4

0.5p

L103

10u

2SC4617(S)Q104

R33

8

220

C18

0*

CN301E23-0762-05

R141*

C35

8

470p

L117

220n

C16

6

470p

Q107

BPF GND

L316L39-1272-15

R143*

L116 220n

C15

0*

C158*

C19

0*

D116*

L125

*

L113

220n

L323

680n

R157*

L106

220n

R133

0

L324

180n

R323

22

L317L39-1272-15

C37

215

p

D10

6

1SV

282-

F

C36

7

0.1u

R12

8

47

L325 1u

Q105SSM6L05FU

R123

0

C171

0.5p R178

56

R16

2

10k

D11

7*

2SC5108(Y)FQ112

R329

0

L322

560n

L318

BPF

C34

8

5p

D108

1SV282-F

C17

4*

L321

560n

C355

0.5p

R13

7

1.5k

R142*

L319L39-1272-15

C17

2

0.5p

C159

47p

C18

547

0p

D10

2

1SV

325F

L114

23n

R13

8

100k

L313

15nR

163

*

L108

220n

C143

470p

C381

0.01u

C386

8p

C16

3*

C1605p

R15

9*

C17

7*

R14

6

220

R14

5

100k

C16

7

470p

L121

220n

C18

7*

2SC5108(Y)FQ109

C149*

*

C354

470p

R148

22

D10

7

1SV

282-

F

C42

3

6p

C362*

L115*C182

470p

R17

4*

R140

47k

C361

470p

R16

0*

C13

7

100p

C18

9*

R144

1k

R15

6*

L102

10u

L314

18n

R16

4

10k

L118

*

L105

220n

D104

1SV282-F

D113*

D11

5

1SV

278F

2SK1215-E(E)Q302

R149

150k

C17

8

470p

D114*

D11

1

1SV

282-

F

C18

6

1u

C37

9

0.01

u

L120

220n

R32

2

270

C13

8

100p

R330

0

R32

5

270

C38

2

0.01

u

D109

1SV282-F

R32

4

270

C374

27p

2SC5108(Y)FQ111

L128

*

L104

220n

R16

722

0

L107

L119

*

C17

9

470p

C18

4

470p

C169*

L126

*

2SJ347FQ108

L111

220n

R136*

C357*

C370

0.01u

L123*

R15

8*

C14

7

4.7u

R155*

C36

3

470p

L127

10n

XF300L71-0551-45

R17

5*

R33

7

47

C360

470p

Q110*

C14

8

470p

C387

470p

C38

3

22p

L122

C175*

C16

5

4p

L109

220n

L112

220n

R16

6

330

C16

8

470p

C349

2p

C183

470p

IC302SPM5001

1G12D13D24 S2

5 S1

6 G2

L124

18n

R16

5*

R15

3

100

R32

8

10

C161 5p

C130

47p

R32

6

2.2k

R15

1

56

C17

3*

R1240

2SK508NV(K52)Q106

R14

7*

C16

4*

5R

R13

9

470k

S33

A

S33

A

5CT/R

R150

100

5C

5R

RX VCO

TX VCO

D106,107,110,111,112

FREQUENCY CONTROL

D102,104,105,108,109

FREQUENCY CONTROL

T/R SW

IF AMP

RIPPLE FILTER

VCOOSCILLATION

BUFFER AMP

VCOOSCILLATION

OPTION

CPU CPU

OPTION

PO

WE

R

CP

U

POWER

CPU

POWER

SP+

MICE

SP- SP-

MICE

SP+MIC MIC

T/R

5R

DSP-FPGADSP-FPGA

1st Lo

2V

HVC131

NO

D113

-10,-11,-12

-13,-14,-15

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

X57-7250-XX

K4,K5,K6

K,K2,K3

K4,K5,K6

K,K2,K3

-13,-14,-15

X57-7250-XX

-10,-11,-12

D114

HVC131

NO

D116

HVC131

NO

D117

HVC131

NO

Q110

2SC5108(Y)F

NO

L122

L92-0446-05

NO

Q107

2SK508NV(K52)

2SK508NV(52K) 23n

33n

L115

NO

L118

3.3n

2.7n

L119

1.8n

NO

L123

22n

22n

L125

15n

NO

L126

10n

22n

L128

27n

22n

L315

NO

R136

33k

22k

R141

NO

0

R142

47k

NO

R143

47k

NO

R147

220

270

R155

27

39

R152

NO

22

R156

180

150

R157

47k

NO

150

R160

180

R163

NO

0

R165

10k

NO

R174

NO

270

0

R175

270 39p

C149

15p

1p

C150

0.5p

27p

C151

22p

6p

C156

5p

5p

C157

2p

47p

C158

NO

10p

C162

NO

12p

C163

8p

5p

C164 C169

2p

C173

NO6p 3pNO

9p

C174

6p 4p

C175 C176

2.5p

C177

NONO 4p2p

100p

C180

10p 15p

C189 C190

47p

C187

NO5p NO

47p 470p

NO

C357

15p

470p

C362

DBM

T/R SW

BUFFERAMP

BUFFER AMP

BUFFER AMP

FM MODULATIOND115

FREQUENCYCONTROL

D116,117

FEEDBACKFILTER SW

D113,114

1st L

o

R158

47k

NO

R159

NO

220k

R15

2

**

R:1.37VT:0V

R:0.51VT:0V

R:4.92VT:0V

R:4.87VT:0V

3.32V

4.98V 4.27V

R:4.26VT:0V

R:0VT:4.19V

0.75V

3.91V

2.12V 4.73V

1.54V

Z AA AB AC AD

X57-725 6/12

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

Page 84: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310 SCHEMATIC DIAGRAM

C405

0.01u

L206*

C36

5

470p

C67

4

470p

C411

150p

R22

20.

22

CF300L72-1017-05

R23

2

150k

(D)

R33

6

47

R21

6*

C29

9

470p

SSM3K15TE(F)Q203

C394

0.1u

L208

C218*

R34

822

R36

4

3.9k

R21

2

100k

2nd Lo

R23

5

1M

R20

5

22

C20

1

470p

C390

22p

R21

1

330

R259

0

C39

8

0.1u

R21

3

100k

RD01MUS1-T113Q202

C25

34.

7u

C23

7

0.01

u

R358

4.7k

SSM3K15TE(F)Q206

R224

150k(D)

C4060.01u

C23

5

470p

C23

4

470p

R33

4

47k

R20

4

330

R260

0

R365

47k

R233*

C41

8

0.1u

R26

1

100

R23

1

150k

(D)

C41

9

0.1u

IC308TC7WU04FK-F

11A

23Y

32A

4GND

52Y

63A

71Y

8VCC

R35

3

150k

C421

0.1u

R32

7

3.3k

R202

4.7k

C42

2

0.1u

R17

2

2.2k

C396

0.1u

R219

10k

L327

100nC

227

*

C21

6

470p

C407

10u

R33

3

100k

CF303L72-1017-05

WIDE

R34

3

3.9k

L209

*

C20

0

0.01

u

C402

0.1u

C20

5

470p

C20

3*

C22

8

470p

C41

4

100p

R35

9

1.8k

C20

6

470p

C24

5

470p

R368

100k

L228

18n

R23

8

470k

C400

0.1u

L326

150n

C42

0

2.2u

L204

R21

8

22k

C409

0.1u

C21

0

470p

C38

9

47p

R22

6

150k

(D)

R36

1

3.3k

C231

100p

C399

1000p

C392

47p

R21

7

100

R240

2.2k

CD300

L79-1850-05

C395

0.1u

C24

0

470p

D20

1H

ZU

5CLL

2SC5108(Y)FQ200

C22

9

0.01

u

C24

1

470p

C41

3

0.02

2u

C226

470p

R34

4

3.9k

C22

4*

R170

0

C401

0.1u

2SK3077FQ210

R229

150k(D)

C220

470p

R223

47k

R347

1k

SSM3K15TE(F)Q208

C404

0.1u

C38

8

0.01

u

C39

1

82p

IC307TC7W53FK(F)

1CoMMoN

2INH

3VEE

4GND

5 A

6 CH1

7 CH0

8 VCC

R362

2.7k

Q205EMD9

R339

0

R21

4*

C21

9

0.01

u

R23

0

33k

C23

9

470p

IC304TA31137FNG

1 oSCIN

2 oSCOUT

3 VCC1

4 MIXoUT

5 VCC2

6 IF1IN

7 DEC1

8 IF1oUT

9 NDPS

10 IF2IN

11 DEC2

12 GND2 13IF2oUT

14QUAD

15AFoUT

16N-REC

17FILIN

18FILoUT

19N-DET

20C-DET

21RSSI

22VREF

23GND1

24MIXIN

C22

3

470p

IC201TA75W01FUF

1oUT1

2IN1-

3IN1+

4VEE

5IN2+

6IN2-

7oUT-B

8VCC

R225

150k(D)

C22

5*

C38

0

0.01

u

L201

*

R22

1*

C23

8

1u

R22

8

10k

R20

0

3.3k

CF301L72-1009-05

P25

2SC5108(Y)FQ303

R357

56k

R22

00.

22

R37

2

47

R263

8.2k

C393

0.1u

CF302L72-1021-05

NARROW

C207

7p

R234

10k

R23

6

47k

L200* C22

1

15p

L212

D200

HVC131

C23

2*

C24

4*

C385

47p

C40

8

0.1u

R340

8.2k

C41

5

1000

p

R34

9

22

R20

3

33

IC306TC7W53FK(F)

1 CoMMoN

2 INH

3 VEE

4 GND 5A

6CH1

7CH0

8VCC

R341

47

C410

39p

C23

0

470p

R22

7

22

D30

8

HV

C13

1

C202*

R23

9

100k

C41

6

0.1u

C24

7

470p

IC200TC75W51FK(F)

1

2

3

4 5

6

7

8

R20

1*

C209

470p

C403

0.1u

L203

*

L225*

R35

6

15k

C188

470p

C412

150p

R370

47

R215*

R36

0

3.9k

C21

5

470p

IC305TC7W53FK(F)

1CoMMoN

2INH

3VEE

4GND

5 A

6 CH1

7 CH0

8 VCC

R26

2

2.2k

C39

7

68pR34

2

680k

R264

0

Q207DTA144EE

IC303TC7W53FK(F)

1 CoMMoN

2 INH

3 VEE

4 GND 5A

6CH1

7CH0

8VCC

Q304EMD9

C20

4*

L210

*

X300L77-1961-05

oUTPUT3

VCC41 VC

2 GND

33A

5R 5T

VN 33

A

33A

IF_I

N

RS

SI

5R

L2S

F

5T AP

CS

W

5M +B

AP

CS

W

AP

C

5T 5M

R23

7

180k

WN

LOCAL SW

LOCAL SW

W/N SW

RF AMP

RF AMP

APC SW

RF DRIVE AMP

AUTO POWER CONTROL

DC AMP

MULTIPLEXER

FM IC

BUFFERMULTIPLEXERMULTIPLEXER

CPU

OPTION OPTION

CPU

CPU

POWER

CPU

POWER

POWER POWER

SP+

MICE

SP- SP-

MICE

SP+

VOLTAGEPROTECTION

MIC MIC

VCXO

+B

DSP-FPGADSP-FPGA

1st Lo

APC

NO

L225

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

L210

22n

R214L209 R221

270 270

5p

C218

-10,-11,-12

-13,-14,-15

15n

6p

6.8n 470p

8.2n

L206L200

7p

X57-7250-XX

180

22

R201 R233

18n 7p

1K,K2,K3

39n

C202

18n

NO1.5k

22p

R215

4718015n

1.8kNO

NO

L201 C203

K4,K5,K6

R216 C204

0

18n

18NO

15n

18n

33

L203 C224

39p

27p

C225

NO

470p

C227

470p

NO

C232

NO

22p

C244

470p

NO

MULTIPLEXER

APC SW

APC SW

APC SW

2ND LOCALBUFFER AMP

3.3V 5VLEVEL CONVERTER

R36

6

22

R:2.42VT:0V

R:0VT:2.40V

R:0VT:0.82V

R:0VT:4.74V

R:0VT:0.86V

T:1.71V(H)1.34V(L)

0.64V

3.26V

FM:3.32VP25:0V

P25:0VW:3.18VN:0V

T:7.2V(H)7.4V(L)

R:0VT:4.94V

AE AF AG AH AI

X57-725 7/12

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

Page 85: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310SCHEMATIC DIAGRAM

D

D

-t

D

D

D

L220 4T

C270

470p

R625 10k

R640 470k

C29

1

4p

L213

820n

C27

747

0p

L216

4T

R247

2.7k

R636 18k

C675

1000p

C24

2

470p

C29

3

4p

D20

6

EZ

JZ0V

5002

3C

D202

HVC131

R25

4

10k

R637 1k

IC203MASWSS0181

1RF1

2GND

3RF2

4V2

5RFC

6V1

D20

4

HV

C13

1

C29

6*C

297

*

C281*

R665

0

C645 0.01u

C262

470p

C26

8*

R24

5

4.7k

R25

5

10k

L218

D20

7

EZ

JZ0V

5002

3CC

288

*

R25

6

1k

L217

R244

33k

RD07MVS2Q204

C25

2

470p

C257*

L211

ANT GND

R633 0

D20

5

HV

C13

1

C284

470p

C29

5*

C27

3

470p

KMC SW(Y)

IC605TC7SBD384AFU

1A

2B

3G

ND

4oE

5V

CC

C264

1p

CN204

R691

0

R63

0

47k

R631 47

CN601

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

C282*

R641

470k

C271

470p

R242*

R639 1k

L214 4T

L215

4T C289*

R24

327

0

C26

6*

R25

2

18k

C26

0*

C267

1p

C26

1* C

263

* C26

5*

C25

90.

01u

C25

847

0p

L221

3T

L227*

C25

6*

L219 4T

C25

4

470p

C278*

C25

0*

CN609

2oPT3

1oPT1

4TXD1

3RXD1

6oPT4

5NC

8OPT5

7USEL

10AGND

9DGND

12Ao

11AI

145A

13AGND

16DI/ANI

15SToN

18MAN DoWN

17TCoNT

20oPT2

19INH

22RXEo

21TXo

24TXI

23RXEI

26SB2

25oPT6

C24

6

0.01

u

C642 0.1u

C292*

C28

0

470p

C29

0*

R62

6

47k

R688

0

CN205

C644

0.1u

R25

1

100k

C283*

R258

2.7k

R249* C285

470p

RF ANT(Y)

L222

TH

200

B57

331V

2104

J

R642 470k

R638 1k

D203HVC131

R24

627

0

L223

820n

R628 47

C24

3*

R643 470k

IC202 MASWSS0181

1RF1

2GND

3RF2

4V2

5RFC

6V1

C24

9

0.1u

R635 0

C25

5*

L304*

R63

4

10k

2SJ243-AQ209

R629 10k

C643 0.1u

IC604TC7SBD384AFU

1A

2B

3G

ND

4oE

5V

CC

L627

L628

L625

L626

L623

L624

L622

L629

L620

L621

L618

L619

L616

L617

R632

0

ANT

SToN

RXEo

oPT4

TCoNT

oPT2

C3

TXI

SB2

DGND

AGND

TXo

oPT3

AGND

oPT5

MAN DoWN

INH

RXEI

DI/ANI

5A

oPT1

CN923

2

1

4

3

6

5

8

7

10

9

12

11

14

13

16

15

18

17

20

19

22

21

24

23

2625

5M5TWPA

BFSX1

BDX2

36MD

INT0

BCLKX2

BCLKR2

BFSR2

BFSX2

BDR2

33M

D_TXD

RXDM

BDX1

5M

5M

SB

33M

oP_MAN

TXo

SToN

Ao

AI_TX

oPT2

oPT4

oPT5

RXEo

TCoNT

AI

RXEI

TXI

oPT6

oP_INH

RXD1

oPT1

oP_TXD1

oPT3

L609

L608

TEMPCOMPENSATION(FOR PA)

SURGEABSORPTION

SURGEABSORPTION

ANTENNA SW

D202,203

ANTENNA SW

RF FINAL AMPSPDT

UART SW

OPTION

CPU CPU

CPU

POWER

POWER POWER

SP+

MICE

SP- SP-

MICE

SP+MIC MIC

+B

DSP-FPGA

D204,205

TX-RX UNIT :OPTION SECTION(X57-7250-XX)(D/5)

SB2

DI/ANI

DGND

INH

NC

AGND

oPT2

TXo

RXEI

TXI

NC

C3

oPT4

RXEo

TCoNT

AGND

oPT5

SToN

5A

MAN DoWN

AGND

DI/ANI

TXo

NC

TCoNT

INH

MAN DoWN

TXD1

oPT4

NC

TXI

SToN

AGND

oPT1

RXEI

DGND

oPT1

oPT2

C3

oPT5

5ASB2

oPT3

RXD1

oPT3RXEo

NO

C256C255

100p0

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

C257R242L304

470p4.7n

0

C260

-13,-14,-15 7p

NO

R249L227

15p

9p-10,-11,-12

NO 8.2p

NO

C261

2pNO

4p

K4,K5,K6

C263X57-7250-XX C243

47p

10p

C250

K,K2,K3

10n

2pNO

68p 18p

7p27p 6p

C265 C281

4p

C282

NO 0.5p

6p 15p

9p

15p

C278C268

7p

9p9p

C283C266 C288 C296

3p 8.2p

6p

C289 C290

18p

12p

5p

2.5p

NO5p

2.5p3p

C295

6p

C292

33p

NO

C297

7p

9p

SPDT

UART SW

SPDT EXT/INT SW

BIo

T:2.49V(H)1.85V(L)

T:7.2V(H)7.4V(L)

R:0VT:1.60V

R:0VT:0.8V

X57-725 8/12

AJ AK AL AM AN

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

Page 86: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310 SCHEMATIC DIAGRAM

D

D

D

D

D

D

D

CN941

R673*

L613

IC607TC7MB3245FK

1NC

2A1

3A2

4A3

5A4

6A5

7A6

8A7

9A8

10GND

11B8

12B7

13B6

14B5

15B4

16B3

17B2

18B1

19oE

20VCC

R677*R678*

IC609TC7WB125FK

1 oE12 A13 B24 GND 5

A2

6B1

7oE2

8VCC

C65

410

0p

IC608TC7WB125FK

1 oE12 A13 B24 GND 5A2

6B1

7oE2

8VCC

25D(Y)

R65

0

4.7k

C66

010

0p

R664 1k

R682*

R681*

R658 470

R65110k

R676*

R679*

R657 1k

R663 1k

C64

8

0.1u

C66

410

0p

L611

C65

710

0p

C64

9

0.1u

C66

810

0p

0.1u

C65

0

C65

310

0p

R675*

C66

910

0p

CN613*1

LCS2

GND3

DO4

D15

D26

D37

D48

D59

D610

D711

RD12

WR13

GND14

AO

R659 1k

R666 1k

R661 1k

R672*

L612

CN612

1 GND2GND

3 MIC4MICE

5 SP+6PWR

7 SP+815V

9 SP-10SB1

11 SP-12+B

13 AF14+B

15 VoL16+B

17 CLK18+B

19 GND20LRST

21 KIN2228M

23 EXAFC24PSW

25 KES26INAFC

27 DAT28EXSW

29 TGL03033M

31 TGL23233M

33 TGL13433A

35 CH_A3633A

37 CH_B3825D

39 CH_C4015D

41 CH_D4215D

43 PTT445M

45 NC465M

47 oE48LCDV

49 DGND50DGND

C66

110

0p

C66

510

0p

R65

3

10

R680*

R674*

R6520

C65

110

0p

5M

PSW

D7

D4

CH_B

VoL

CH_A

LCDV

D6

LRST

5AC

D2

D0

25D

5M

33M

D5

D3

CH_C

WR

TGL2

D1

TGL1

A0

33A

33M

LCS

15D

PWR

15V

DAT

LCDV

15V

KIN

KES

oE

SB1

KIN

PTT

CLK

5M

TGL0

CH_D

CN800* 14LCS

13GND

12DO

11D1

10D2

9D3

8D4

7D5

6D6

5D7

4RD

3WR

2GND

1AO

CN700

2GND 1 GND

4MICE 3 MIC

6PWR 5 SP+

815V 7 SP+

10SB1 9 SP-

12+B 11 SP-

14+B 13 AF

16+B 15 VoL

18+B 17 CLK

20LRST 19 GND

2228M 21 KIN

24PSW 23 EXAFC

26INAFC 25 KES

28ECSW 27 DAT

3033M 29 TGL0

3233M 31 TGL2

3433A 33 TGL1

3633A 35 CH_A

3825D 37 CH_B

4015D 39 CH_C

4215D 41 CH_D

445M 43 PTT

465M 45 36MD

48LCDV 47 oE

50DGND 49 DGND

D70

8

MA

2S11

1-F

C78

8

10u

R70

1

1k

C70

2

10u

C70

4

10u

C700

0.1u

R70

2

100k

SSM3K15TE(F)Q700

R70

5

1k

R710

33k

R708

2.7k

Q701UMG3N

R7111.2k

2SB798(DL,DK)Q702

L700

SSM3K15TE(F)Q703

2SJ243-AQ704

R713

1M

R709

47

C70

3

470p

C70

1

470p

IC800*1 OUTPUT

2 V+

3 INPUT+ 4INPUT-

5V-L801*

R801*

C80

8*

C84

2*

R80

6*

R805*

C814*

R80

4*

R70

6

330

D4

LCS

A0

D6

D7

D1

WR

D2

D0

D5

D3

PTT

INAFC

PWR

DAT

CHB

KEY1

KESECSW

CHA

CHC

LCDV

EXAFC

VoL

oE

CLK

TGL2

TGL0

PSW

LRST

TGL1

CHD5M

36MD

15D

25D

33A

15V

28M

SB

33M

+B

L615

5M

L614

TX-RX UNIT :ANT SECTION(X57-7250-XX)(E/5)

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

BUS SW(8ch)

CPU

POWER

SP+

MICE

SP-

MIC

K2,K5-11,-14

K3,K6

-10,-13

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

-12,-15

K,K4

X57-7250-XX

470p

CN800

NO

R805

0

R801

E41-1634-05

10M

E41-1634-05

R806

33k

C808R804

NO NO

100k

NO

NONO

0.01u0

NO

L92-0446-05

10M

IC800

C814

LMC7101BIM5

33k 470p

LMC7101BIM5

NO

100k

L92-0446-05

L801

0.01u

NONO

E41-1634-05

CN613

E41-1634-05

R672

100

100

NO

R673

NO

100

100

R674

NO

100

100

R675

NO

100

100

R676

NO

100

100

R677

NO

100

100

R678

NO

100

100 100

R679

NO

100

100

R680

NO

100 100

100

R681

NO

100

100

R682

NO

EXT ANT

GND

GND

28M

EXTERNALAUDIO MUTE SW

MIC

33M

MICE

SP-

GND

Q704

S_EXAFC

DC AMP forLCD VOLTAGE

EXTERNALAUDIO MUTE SW

5M

5V AVR

INAFC

SP+

KIN

AF

+B

5V AVR SW

ECSW

D708

5VAVRSW

REVERSECURRENTPREVENTION

K3,K6

-10,-13 K,K4

X57-7250-XX

K2,K5

-12,-15

-11,-14

NO

0.022u

C842

0.022u

K,K4

K3,K6

X57-7250-XX

-10,-13

K2,K5-11,-14

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

-12,-15

BUS SW(2ch)

BUS SW(2ch)

R70

7

100k

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

14.50V

10.49V

X57-725 9/12

AO AP AQ AR AS

Page 87: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310SCHEMATIC DIAGRAM

5M

CLK

L_MIC

DAT

D5

KE

S

D6

oE

D0

D7

D1

D2

keyB

D3

keyA

keyC

D4

A0

WR

5M

keyD

key5

LCS

key1

key3

LRS

T

key2

MICE

key4

C80

1* C

803

*C80

2*C

800

* C80

5*

R813*

key4

keyA

R815*

key0

R810*

keyD

key5

R808*

R819* key7

R807*

key2

R816*

R809*

key#

R812*

keyB

key3

R814*

R811*

key9

R821*

key1

keyC

R820*

key6

R817*R818*

key*

key8

R822*

CN802*1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

L800

* C80

7*

LCD(Y) C810*C811*

C809*

C81

2* R

823

* R82

4* C

825

* R82

8*

R82

7*

S800 S805 S810 S815

S804

S802

S801

S803

S806

S809

S808

S807

S811

S812

S813

S814

IC701TC7W66FK-F

1IN_oUT1

2oUT_IN1

3CoNT2

4GND

5

IN_oUT2

6

oUT_IN2

7

CoNT1

8

VCC

IC702LM4906LD

1SHUTDoWN

2GND1

3GAIN_SELECT

4INPUT

5NC1

6

NC2

7

Vo1

8

VDD

9

GND2

10

Vo2C707

0.1u

R71

9

47

R72

0

1M

C708

1u

R7181M

SSM3K15TE(F)Q705

2SJ243-AQ706

D70

0

1SS

388F

L701

L702

L703

L704

C71

6

0.1u

C71

8

470p

C71

2

2.2u

R72

2

1k

R72

3

100k

IC703LM4906LD

1SHUTDoWN

2GND1

3GAIN_SELECT

4INPUT

5NC1

6NC2

7Vo1

8

VDD

9GND2

10Vo2

R72

1

1M

C7091u

C71

3

2.2u

C71

9

470p

C71

7

0.1u

D71

1

AV

RM

1005

C27

0M

D71

0

AV

RM

1005

C27

0M

C72

4

1u

R72

6

0

SSM3K15TE(F)Q708

R72

8

2.2k

R729

22k

C726

0.1u

C72

8

100p

R73

4

180k

R73

3

150k

C72

7

2.2u

R732

150k

R731

680k

28M(Y)

D701

1SS388F

C72

5

1u

C79

5

1u

R735

33

R730

1k

CN702

J19-5386-05

IC704XC6204B302M

1VIN

2VSS

3CE

4NC

5VoUT

R784

470k

C72

9

0.1u

C73

1

0.1u

R737

47

R74

7

1.8k

C73

0

0.47

u

R74

3

22k

R744

22k

C737

0.47u

R73

8

27k C73

6

0.47

u

R741

47k

R739

22k

C73

2

0.02

2u

R74

2

1.8k

R746

47k

R74

5

47k

C73

8

470p

C73

4

470p

Q709UMC4N

D702NNCD6.8G-A

C73

947

0pIC705

TC75W51FK(F)

1

2

3

4 5

6

7

8

D805*

D804*

IC801BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9QS

10Q’S

11Q8

12Q7

13Q6

14Q5

15OE

16VDD

C82

6

0.01

u

D81

3*

L803

L802

*

* LCDV

4

V3

V2

V1

V0

VR

NC

GN

D

NC

GN

D

VD

D

D7

Vou

t

NC

NC

NC

NC

NC

D6

D5

D4

D3

D2

D0

D1

A0

LRS

T

E/R

D

WR

LCS

1k

1k

NO

R807

NO

YES

NO

D804

E40-6337-05

NO

IMN10

LCD

E40-6337-05

IMN10

CN802

YES

NO

C812C800

NO

0.47u

0.47u

R808

1k

1k

NO

NO

22k

22k

R823

NO

R827

22k 470p

470p

NO

C807 C809

NO

1u

1u

C810

NO

1u

1u

C811

NO

1u

1u

R809

1k

NO

1k

NO

L92-0446-05

L800

L92-0446-05 L92-0446-05

L92-0446-05

NO

L802

R824

22k

NO

22k

D805

NO

IMN10

IMN10

D813

NO

IMN10

NO

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

0.47u

C801

NO

0.47u

0.47u

C802

NO

0.47u

0.47u

C803

NO

0.47u

0.01u

C805

NO

0.01u

C825

470p

470p

NO

VOLTAGEREGULATOR(28M)

D804,805

SHIFT REGISTER

ECSW

STRB

KIN

SP+

INAFC

AUDIO AMP

CLK

INTERNALAUDIO MUTE SW

oE

MICE

AUDIO AMP

SP-

REVERSECURRENTPREVENTION

S_EXAFC

+B

5M

AF

EXT/INTGAIN CONVERT SW

NOISECANCELER SW

KIN

GND

AF MUTE SW

33M

REVERSECURRENTPREVENTION

INTERNALAUDIO MUTE SW

MICE

MIC

28M

MIC

SURGEABSORPTION

DATA

OP AMP(AF PRE-AMP/TX AF AMP)

+B

AF

33M

28MECSW

A

0

B

9

D

2

6

1

5

#

4

8

3

C

7

Li-CELL:W09-0971-05

+B

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

K3,K6

-10,-13 K,K4

X57-7250-XX

K2,K5

-12,-15

-11,-14

-11,-14

X57-7250-XX

-10,-13 K,K4

K2,K5

K3,K6-12,-15 1k

1k

NO

R810

NO

R811

1k

NO

R812

NO

1k

NO

R813

NO

1k

NO

R814

NO

1k

NO

R815

NO

1k

NO

R816

NO

1k

NO

R817

NO

1k

NO

R818

NO

1k

NO

R819

NO

1k

NO

R820

NO

1k

NO

R821

NO

1k

NO

R822

NO

1k

NO

-11,-14

X57-7250-XX

-10,-13

K3,K6

K,K4

-12,-15

K2,K5

22k

NO

470k

R828

470k 1u

1u

R71

4

100k

X57-725 10/12

AT AU AV AW AX

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

Page 88: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310 SCHEMATIC DIAGRAM

+B(Y)

L_KEY1

PF1

L_PTT

PF2

GND(Y)

L_PTTG

PF3

key*

key#

key6

PT

T

key8

5AC

key0

key9

POWER(Y)

PS

W

key7

L707

R79

8

470k

IC706XC61CC5602NR

1VoUT

2

VIN

4 VSS

3NC

R748

10k

Q713UM6K1N

C74

0

470p

D814*D816*

IC802BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9QS

10Q’S

11Q8

12Q7

13Q6

14Q5

15OE

16VDD

C82

9

0.01

u

D81

7IM

N10

D81

8IM

N10

IC803BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9QS

10Q’S

11Q8

12Q7

13Q6

14Q5

15OE

16VDD

C84

0

0.01

u

R849 1k

R847 1k

R850 1k

R851*

R855 1k

R859 1k

R860 1k

R852 1k

R856 1k

R858 1k

R857 1k

*R82

6

R82

5* R

829

* R83

0*

D80

0* D

802

*

D80

6* D

808

*

D80

7*

D80

3*D

801

*

R83

1* R

832

* R83

3*

D81

0* D

811

* D81

2*

C827*

R83

5* R

836

*

Q800*D815*

C82

8*

Q801*

L705

C741

470pC

745

4.7u

C74

64.

7u

C742 4.7u

C743 4.7u

TPC6108-FQ710

36V(Y)

D704HRB0502A

IC710XC6365D103M

1 EXIT/

2VDD

3GND

4CE

5

VOUT/FB

R77

2

330k

C76

4

82p

C77

50.

1u

C77

633

u10

R77

0

220k

C76

3

0.1u

R77

3

120k

R790

10k

C74

4

0.01

u

D7031SS301F

Q804SSM6L05FU

Q803SSM6L05FU

R84

5

470k

R85

3

470k

R84

6

470k

R84

3

470k

SSM3K15TE(F)Q802

R839

1kR842

100k

R84

0

470k

PW

R

D80

9*

NO

R836

D807

NO

D800

100p

R851

B30-2261-05

100

2.2k

B30-2171-05

NO

1k

R830

D803

C827R825

NO

B30-2171-05

R829

NO

0.1u

R826

B30-2171-05

NO

100

B30-2171-05

D806D802

100

R835

100 100

NO

0.1u2SB798(DL,DK)

D810

NO

NO

470k 1k

D801

2SC4617(S)

NO

2SC4617(S)

NO

100

Q800

NO

NO

NO

D814

NO

Q801

NO

D808

IMN10

NO

NO

R832

180

NO

NO

B30-2171-05

180

2SB798(DL,DK)

NO

C828

100p470k

B30-2261-05

NO

B30-2171-05

B30-2171-05 NO

NO NO

2.2k

NO

NO

B30-2171-05

180

R833

NO

MIC

36M

VOLTAGEDETECTOR(5.6V)

D817,818

LAMP

STRB

BLED

33M

SWITCH(36M DC/DC)

TXLEDBUSY LED SW

CLK

oE

MICE

SHIFT REGISTER

PSW SW

REVERSECURRENTPREVENTION

DC/DC(3.6V)

+B

REVERSECURRENTPREVENTION

SHIFT REGISTER

FLYWHEEL(DC/DC)

KIN

KEY BACK LIGHT

S36M

D800-803,806-809

DATA

OGR

33M

REVERSECURRENTPREVENTION

VOLTAGE DET(UP HARD RESET)

+B

+B

MIC

MICEDC/DC CONVERTER(36M)

DC/DCCONVERTER(36M)CONTROL

SW(BACK LIGHT)

SW(BACK LIGHT)

TX LED SW

REVERSECURRENTPREVENTION

D810-812

LCD BACK LIGHT

AVR forBACK LIGHT LED

-11,-14

X57-7250-XX

-10,-13 K,K4

K2,K5

K3,K6

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

-12,-15

NO

D816

IMN10

NO

B30-2171-05

NO NO

NO

B30-2171-05

D809

B30-2261-05

B30-2261-05

D811

NO

B30-2261-05

B30-2261-05

D812

NO

K3,K6

X57-7250-XX

-11,-14

-12,-15

K,K4

K2,K5

-10,-13

DTZ3.9(B)

D815

NO

DTZ3.9(B)

R831

NO

180

180NO 180

7.5V

3.77V

3.79V

X57-725 11/12

AY AZ BA BB BC

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

Page 89: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

85

TK-5310SCHEMATIC DIAGRAM

S901

D901B30-2019-05

CN902

36M 1

S36M 2

GND 3

VoL 4

33M 5

CH_A 6

TGL2 7

TGL1 8

C 9

CH_B 10

CH_D 11

CH_C 12S902

CN903

1 GND

2 CH_A

3 CH_B

4 CH_C

5 CH_D

6 36M

7 S36M

8 33M

9 TGL0

10 TGL1

11 TGL2

12 BLED

13 TXLED

14 ORG

15 VoL

16 KIN

17 GND

CH_B

L_MIC

CH_A

TGL1

TGL2

TGL0

33A

15D

15V

L_KEY1

L_PTT

33M

PF2

PF1

36M

PF3

VoL

L_KEY1

L_PTTG

MICE

CH_D

CH_C

CN8031

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

R841 1k

CN7131

2

3

4

5

6

C78

5

470p

L708

L709

C78

4

470p

C78

3

470p

L804

L805

C831 4700p

C830 4700p

C832 4700p

C833 4700p

C834 4700p

C837 4700p

C838 4700p

C835 4700p

C836 4700p

R844 470

R854 470

C84

1

4700

p

R848 1k

CN804

1

2

3

4

5

6

D705DA221

D706DA221

D70

7C

US

01

33M(Y)C

762

470p

C76

9

1u

IC707XC6204B332M

1VIN

2VSS

3CE

4NC

5VOUT

C74

9

0.1u

R758

2.2

IC708XC6204B332M

1VIN

2VSS

3CE

4NC

5VOUT

C76

0

470p

C76

5

1u

33A(Y)

C75

0

0.1u

R759

2.2

C75

4

0.01

u

Q712UM6K1N

R79

710

0k

R79

610

0k

IC709XC9225A15CM

1 VIN

2 VSS

3 CE/MoDE 4VoUT

5LX

15D(Y)

L807

C76

1

470p

C76

6

4.7u

IC712TK11250CUCB

1NP

2GND

3CoNT

4VIN

6VoUT

C77

0

470p

C77

4

1u

5M(Y)

5M

C75

3

1u

IC711XC6204B252M

1VIN

2VSS

3CE

4NC

5VOUT

C76

8

470p

C77

3

1u

25D(Y)

C75

7

0.01

uC74

7

0.1u

R753

2.2

25D

SB(Y)C79

0

470p

C75

1

4.7u

IC713XC9101D09AKR

1 EXT

2 LSEN

3 VIN

4 CE/SS 5CLK

6CC/GAIN

7VoUT/FB

8VSS

R77

112

k

C76

718

0p

C77

247

0p

R77

522

kR

774

330k

C77

122

p

C77

91u

C77

71u

C77

81u

15V(Y)

Q711SSM5H01TU

L706

68u

SB

1

C75

90.

1u

R768

150k

C75

21u

C75

54.

7u

R762

10

C74

81u

R754

33

INT SP

SIDE KEY SECTION

NC MIC

CONCENTRICSW

POWER SW/AF VOL

CHANNELSELECTOR

TX-RX UNIT :TOP SECTION(X57-7250-XX)(C/5)

TX/RX LED

INT MIC(MAIN)

TOP SW SECTION

SIDE 2

SIDE 3

PTT

SIDE 1

36M

INT SP

DC/DCCONVERTER(15V)

VOLTAGE REGULATOR(33A)

(MAIN)

33M

BLED

DC/DC(15V)

D705

TXLED

VOLTAGE REGULATOR(33M)

S36M

DC/DC CONVERTER(15D)

33A

INT MIC

33M

OGR

D706,707

+B

MIC

DC/DC(1.5V)

MICE

VOLTAGE REGULATOR(25D)

VOLTAGE REGULATOR(5M)

SWITCH(15V DC/DC)

DSPPOWER SUPPLYTIMING CONTROL

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

1.51V

3.3V

2.51V

14.51V

3.76V

3.78V

7.49V

3.32V

4.98V

7.43V

3.73V

3.67V

BHBGBFBEBD

1

2

3

4

5

6

7

X57-725 12/12

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

Note : The components marked with a dot ( ) are parts of layer 1.

Page 90: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

E

D

D

D

D

D

D

D

D

D

D

D

D

E

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

E

D

E

D

E

D

D

D

E

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

E

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

-t

D

D

D

D

D

D

D

D

D

D

D

D

E

DD

E

D

D

E

D

D

PO

WE

R

POWER

RX

RF

CN941

C36

8

0.1u

R464

22k

C33

3

470p

R46

6

1.8k

R52

6

47

C405

0.01u

C30

2

1u

C51

0

1u

C10

2

47p

R132

0

L315*

L220 4T

C270

470p

C151*

R625 10k

R46

9

220k

L206*

R572

4.7k

R43

100

R582

470kC170

2p

R51

2

470k

C50

2

0.1u

C36

5

470p

IC100LMC7101BIM5

1OUTPUT

2V+

3INPUT+

4INPUT-

5V-

C62

110

0p

C15

347

0p

R57470k

C67

4

470p

R300

10k

33M(Y)

R478

220k

C411

150p

R640 470k

C50

7

0.1u

R22

20.

22

C530

0.1u

C3

0.1u

C29

1

4p

R67

47k

R673*

CF300L72-1017-05

R23

2

150k

(D)

R26

10k

C37

8

12p

Q102SSM6L05FU

C341*

R33

6

47

R21

6*

C36

6

470p

C29

9

470p

D11

2

1SV

282-

F

D105

1SV282-F

R64

5

100k

L309

*

C176*

R70

47k

C15

2

2.5p

R502

10

C35

6

6p

R57

3

10

R12

0

10M

SSM3K15TE(F)Q203

C145

470p

L613

C394

0.1u

L208

C533

10u6.3

C30

0

0.1u

L213

820n

C27

747

0p

C50

6

0.01

u

R31

4

100k

C48

2

0.1u C

156

*

C218*

C315*

R34

822

R465

4.7k

CP

13

47k

L216

4T

IC601XC6204B502MR

1VIN

2VSS

3CE

4NC

5VoUT

C17

0.1u

R36

4

3.9k

IC607TC7MB3245FK

1NC

2A1

3A2

4A3

5A4

6A5

7A6

8A7

9A8

10GND

11B8

12B7

13B6

14B5

15B4

16B3

17B2

18B1

19oE

20VCC

C10

9

1u

D1

MA2S111-F

L5

F6003.15A

IC5

30625MGP346HU

1BATTDET

2NC(ANEX0)

3ASSIST

4 VoICE5

SoE6

UL7

DAT8

CLK9

SDA10

BYTE11

CNVSS12

STRB13

NC14

RESET15

XoUT16

VSS117

XIN18

VCC119

NMI20

RTCDT21

PSW22

INTRA23

LD24

BEEP25

LE26 BSFT27

KEY/PLAY28

LCDV29

INH30

AUXI31

TCNT32 BEEPS

33T

XD

134

VC

C1

35R

XD

136

VS

S2

37B

US

Y38

RT

SM

/EX

To39

TX

DM

40R

XD

M41

DS

RM

42C

TS

M43

A20

44K

ES

45K

IN46

MoD

EL

47R

DY

48A

LE49

HoL

D50

HLD

A51

WN

52V

N53

EX

TIM

54S

CS

W55

BC

LK56

RD

57B

HE

58W

R59

TG

L060

TG

L161

TG

L262

CS

363

CS

264

CS

1

65CS0

66A19

67A18

68A17

69A16

70A15

71A14

72A13

73A12

74A11

75A10

76A9

77INAFC

78CH_A

79CH_B

80CH_C

81CH_D

82VCC2

83A8

84VSS3

85A7

86A6

87A5

88A4

89A3

90A2

91A1

92A0

93EXAFC

94HINT

95INT3

96PTT

97E

XS

P

98D

RS

T

99F

RS

T

100

NC

101

D7

102

D6

103

D5

104

D4

105

D3

106

D2

107

D1

108

D0

109

5TC

110

5RC

111

5CC

112

AP

CS

W

113

CA

E3

114

VU

115

MM

116

PW

R

117

WPA

118

SQ

119

CV

120

RS

SI

121

TE

MP

122

BAT

T

123

RE

M

124

AV

SS

125

VoL

126

VR

EF

127

AV

CC

128

T/R

R21

2

100k

R28

47k

L301

39n

D110

1SV325F

C61

3

470p

C35

1

10p

L450

R55

747

R49

0

100k

R48 0

D60

1

AV

RM

1005

C27

0M

C14

2

0.47

u35

CP12 100

R29

47k

C11

0

470p

D450RB706F-40

R135

4.7k

2nd Lo

R677*

C457

1u

R23

5

1M

L311

*

C45

5

4.7u

R610

1k

R247

2.7k

R636 18k

R45

7

100k

C15

7*

C675

1000p

R55

447

C24

2

470p

R20

5

22

R33

5

680

R40

100

L602

R302

560k

C51

9

100p

C29

3

4p

L607

C20

1

470p

R546

120k

C390

22p

R553

39k

R455

22k

SSM3K15TE(F)Q457

C16

2*

D20

6

EZ

JZ0V

5002

3C

C60

91u

R21

1

330

C144

10u6.3

IC3AT2425610TI27

1A0

2A1

3NC

4GND

5SDA

6SCL

7WP

8VCC

R259

0

C39

8

0.1u

C32

7

1u

C15

5

470p

C15

4

0.5p

R678*

C32

4

470p

R304

10k

C8

470p

C532

0.1u

R21

3

100k

D202

HVC131

C54

1

10u

L103

10u

R31

9

100k

2SC4617(S)Q104

C62

2

100p

C336*

RD01MUS1-T113Q202

C33

4

470p

R45

8

1M

C25

34.

7u

R33

8

220

C23

7

0.01

u

C18

0*

R58

9

100k

CN301E23-0762-05

C10

6

470p

C63

9

0.1u

R31

6*

33A(Y)

R25

4

10k

R45

0

470k

R141*

C461

0.1u

R358

4.7k

C35

8

470p

L117

220nIC463

TC75W51FK(F)

1

2

3

4 5

6

7

8

C16

6

470p

C52

6

100p

Q107

SSM3K15TE(F)Q206

IC609TC7WB125FK

1 oE12 A13 B24 GND 5

A2

6B1

7oE2

8VCC

C63

1

470p

R224

150k(D)

R53

4

100k

C65

410

0p

SSM3K15TE(F)Q456

R42

100

C60

2

470p

BPF GND

C4060.01u

R7

47k

R127

6.8k

L316L39-1272-15

R76 47k

IC301LMC7101BIM5

1O

UT

PU

T

2V

+

3IN

PU

T+

4IN

PU

T-

5V

-

R637 1k

C23

5

470p

C48

7

0.1u C

342

*

C23

4

470p

R31

470k

IC608TC7WB125FK

1 oE12 A13 B24 GND 5A2

6B1

7oE2

8VCC

R143*

C60

5

470p

IC203MASWSS0181

1RF1

2GND

3RF2

4V2

5RFC

6V1

D20

4

HV

C13

1

R33

4

47k

C49

8

1200

p

C11

1

1u

R20

4

330

R374*C624 100p

C63

010

0p

C63

4

470p

L116 220n

C49

6

0.1u

R260

0

R47

2

470k

C132

470p

R365

47k

R233*

C15

0*

C63

6

470p

25D(Y)

C41

8

0.1u

R26

1

100

C7

470p

R65

0

4.7k

R38

470

C66

010

0p

C29

6*

R575

470k

R23

1

150k

(D)

R471

10

C29

7*

C158*

C14

1

470p

IC606BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9

QS

10

Q’S

11

Q8

12

Q7

13

Q6

14

Q5

15

OE

16

VDD

C41

9

0.1u

C10

0.1u

R60

947

0k

C30

8

470p

IC308TC7WU04FK-F

11A

23Y

32A

4GND

52Y

63A

71Y

8VCC

C28

4.7u

R35

3

150k

R60

4

470k

C32

0.01

u

R3

47k

C19

1

470p

C421

0.1u

C281*

L307

R32

7

3.3k

C62

7

100p

R570

3.3k

C5

0.1u

Q606UM6K1N

R202

4.7k

R61

3

470

R664 1k

R27 1k

R682*

R665

0

C63

8

470p

C19

0*

C42

2

0.1u

C33

5*

D116*

R52

100k

R17

2

2.2k

R60

0

470k

C396

0.1u

C136

0.01u

C11

0.1u

L125

*

C52

9

0.01

u

C53

9

100p

D609NNCD6.8G-A

C54

0

0.1u

R219

10kC51

2

150p

C33

2*

R105

47

L327

100n

C22

7*

L6

C21

6

470p

L113

220n

IC458TC7W66FK-F

1 IN_oUT1

2 oUT_IN1

3 CoNT2

4 GND 5IN_oUT2

6oUT_IN2

7CoNT1

8VCC

L323

680n

C645 0.01u

R33

47k

R453

470k

C262

470p

C14

0.01u

R157*

C50

8

0.01

u

C407

10uCP5 100

L106

220n

C26

8*

R24

5

4.7k

R25

5

10k

C504

1u

R106

100

R133

0

L324

180n

R33

3

100k

CF303L72-1017-05

WIDE

C63

2

100p

D451RB706F-40

R49

4

10

R34

3

3.9k

CAE3

R56

6

10k

L209

*

R323

22

L317L39-1272-15

R60

6

470k

L218

R583 47

R681*

R10

47k

C47

5

0.01

u

C20

0

0.01

u

D20

7

EZ

JZ0V

5002

3C

C402

0.1u

C37

215

p

D10

6

1SV

282-

F

C12

5

0.1u

C20

5

470p

C10

5

47p

C20

3*

C22

8

470p

R59

1

68k

C46

3

1u

IC457EX128TQ64I630C

1

GND

2

SROUT(0)

3

SROUT(1)

4 TMS5 GND6 VCCI7 SROUT(2)8 SROUT(3)9 SROUT(4)

10 SROUT(5)11 SROUT(6)12 SROUT(7)13 STRB14 GND15

TESTMODE16 DSPCLK

17

IF_I

N

18

RE

SE

T

19

VC

CI

20D

IFF

21S

RO

E22

VC

CA

23G

ND

24F

LRC

K25

SR

CK

226

FS

CLK

27F

MC

LK28

CLK

OU

T29

FS

OU

T30

SO

UT

31S

RIN

32C

PU

CLK 33

GND

34BUFA(0)

35BUFA(1)

36VSV(VCCA)

37VCCI

38BUFA(2)

39BUFY(3)

40BUFA(3)

41BUFA(7)

42CLK

43BUFA(5)

44VPP(VCCA)

45LP/GND

46

GND

47

BUFA(8)

48

SMPLCLK

49B

UF

Y(0

)

50B

UF

Y(1

)

51B

UF

Y(2

)

52V

CC

I

53B

UFA

(4)

54B

UF

Y(4

)

55N

O

56N

O

57V

CC

A

58G

ND

59B

UF

Y(5

)

60B

UF

Y(6

)

61V

CC

I

62B

UF

Y(7

)

63B

UF

Y(8

)

64B

UFA

(6)

R48

1

10k

C41

4

100p

R35

9

1.8k

C28

8*

R452

22k

C36

7

0.1u

C10

7

470p

R303

10k

R31

8

100k

R8

10k

C1

0.1u

R618470

R24

10k

2SC4617(S)Q460

C45

4

4.7u

IC462M62364FP-F

1VIN1

2VoUT1

3VoUT2

4VIN2

5VDD

6LD

7CLK

8DI

9VIN3

10VoUT3

11VoUT4

12VIN4

13VIN5

14VoUT5

15VoUT6

16VIN6

17D0

18VDAREF

19RESET

20GND

21VIN7

22VoUT7

23VoUT8

24VIN8

R47

100

C20

6

470p

R12

470k

C476

1u

R55

2

22k

R12

8

47

C24

5

470p

R34

470k

C346*

L325 1u

R451

22k

Q105SSM6L05FU

GND(Y)

R492

10

R658 470

R531 1k

R25

6

1k

C32

1

470p

R495

220k

R368

100k

R123

0

R10

2

47k

L228

18n

C171

0.5p

C53

5

0.1u

R59

0

1k

R69

47k

R61

4

1k

L217

R54 100

IC8

A1

CV

SS

1B

1A

22C

2C

VS

S2

C1

DV

DD

1D

4A

10D

3H

D7

D2

A11

D1

A12

E4

A13

E3

A14

E2

A15

E1

CV

DD

1F

4H

AS

F3

DV

SS

1F

2C

VS

S3

F1

CV

DD

2G

2H

CS

G1

HR

_WG

3R

EA

DY

G4

PS

H1

DS

H2

ISH

3R

_WH

4M

ST

RB

J1Io

ST

RB

J2M

SC

J3X

FJ4

HoL

DA

K1

IAQ

K2

HoL

DK

3B

IoL1

MP

_MC

L2D

VD

D2

L3C

VS

S4

M1

BD

R1

M2

BF

SR

1 N1CVSS6

N2BCLKR1

M3HCNTL0

N3DVSS5

K4BCLKR0

L4BCLKR2

M4BFSR0

N4BFSR2

K5BDR0

L5HCNTL1

M5BDR2

N5BCLKX0

K6BCLKX2

L6CVSS7

M6HINT

N6CVDD4

M7BFSX0

N7BFSX2

L7HRDY

K7DVDD4

N8DVSS6

M8HD0

L8BDX0

K8BDX2

N9IACK

M9HBIL

L9NMI

K9INT0

N10INT1

M10INT2

L10INT3

N11CVDD5

M11HD1

L11

CVSS8

N12

BCLKX1

M12

DVSS7

N13

BFSX1

M13

BD

X1

L12

DV

DD

3

L13

DV

SS

2

K10

CLK

MD

1

K11

CLK

MD

2

K12

CLK

MD

3

K13

HP

I16

J10

HD

2

J11

ToU

T

J12

EM

U0

J13

EM

U1_

oFF

H10

TD

o

H11

TD

I

H12

TR

ST

H13

TC

K

G12

TM

S

G13

CV

SS

5

G11

CV

DD

3

G10

HP

IEN

A

F13

DV

SS

3

F12

CLK

oUT

F11

HD

3

F10

X1

E13

X2_

CLK

IN

E12

RS

E11

D0

E10

D1

D13

D2

D12

D3

D11

D4

C13

D5

C12

A16

C11

DV

SS

4

B13

A17

B12

A18

A13A19A12A20

B11CVSS9

A11DVDD5

D10D6

C10D7

B10D8

A10D9

D9D10

C9D11

B9D12

A9HD4

D8D13

C8D14

B8D15

A8HD5

B7CVDD6

A7CVSS10

C7HDS1

D7DVSS8

A6HDS2

B6DVDD6

C6A0

D6A1

A5A2

B5A3

C5HD6

D5A4

A4A5

B4A6

C4A7

A3A8

B3A9

C3 CVDD7

A2 A21

B2 DVSS9

R511

470k

R65110k

R23

8

470k

C400

0.1u

R11

470k

L326

150n

R47

7

1M

R178

56

R16

2

10k

R244

33k

C42

0

2.2u

R57

6

470k

L204

D11

7*

C13

47p

C61

0

0.1u

R21

8

22k

2SC5108(Y)FQ112

C48

1

0.1u

CP

15

47K

R584 47

C409

0.1u

R329

0

RD07MVS2Q204

C21

0

470p

C25

2

470p

L302

39n

R19 10

X450L77-1962-05

1 VCoNT

2 GND 3oUTPUT

4VCC

F60

1

0.25

A

R307

270k

C33

0.01

u

R13

4

3.3k

C257*

C38

9

47p

L322

560n

Q101SSM6L05FU

L318

C51

5

4.7u

R619 470k

C18

470p

IC452TC75W51FK(F)

1

2

3

4 5

6

7

8

L211

ANT GND

2SC4617(S)Q300

R5

470k

R633 0

R31

3*

R11

4

180k

C488

0.22u

CPUTXDM(Y)

R22

6

150k

(D)

R535

6.8k

D20

5

HV

C13

1

C460

0.1u

R52

047

k

R36

1

3.3k

L606

C34

0

470p

C25

0.01

u

C231

100p

C52

7

0.1u

R676*

C399

1000p

C284

470p

C24

4.7u

R558 100k

R454

10k

BPF

R57

4

470k

C34

8

5p

C60

6

0.1u

R470

470k

R585

470k

C45

9

2.2u

C392

47p

C528

0.1u

R53

2

820

R530 1k

C62

6

470p

D108

1SV282-F

R21

7

100

IC300LMC7101BIM5

1O

UT

PU

T

2V

+

3IN

PU

T+

4IN

PU

T-

5V

-

C17

4*

R20

0

R240

2.2k

C29

5*

R13

470k

CP10 100

R53 100

L321

560n

C355

0.5p

L451

CD300

L79-1850-05

C52

4

0.1u

R510 470k

R32

470k

RXDM(Y)

R60

2

470k

SSM3K15TE(F)Q453

C395

0.1u

C24

0

470p

C513

0.1u

C12

7

470p

R61

6

1k

R620 47k

C30

9*

R507 10

D20

1H

ZU

5CLL

R121

1.2k

2SC5108(Y)FQ200

C27

3

470p

R72 47k

C534

0.1u

C13

1

0.01

u

R13

7

1.5k

C22

9

0.01

u

R54

2

33k

R679*

KMC SW(Y)

C24

1

470p

R9

100k

C41

3

0.02

2u

R142*

C226

470p

C13

9

0.01

u

CP8 100

IC605TC7SBD384AFU

1A

2B

3G

ND

4oE

5V

CC

R563

120k

R34

4

3.9k

Q600SSM6L05FU

R59

5

8.2k

C264

1p

C22

4*

C54

3

100p

L319L39-1272-15

R58

647

0k

R30

9

1M

C17

2

0.5p

R487

47k

C30

0.01

u

C159

47p

CN204

C18

547

0p

R170

0

L1

R657 1k

C6

470p

L3

D10

2

1SV

325F

C19

470p

R691

0

2SC4617(S)Q100

R10

1

470k

R63

0

47k

R56

8

10k

C48

6

1000

p

L114

23n

R301

100k

R663 1k

R21

47k

R13

8

100k

R50

047

R10

9

1k

C64

8

0.1u

R631 47

C32

5

470p

L313

15n

C48

5

1u

C35

0

470p

IC453TC7WH74FK-F

1CK

2D

3Q

4GND

5Q

6CLR

7PR

8VCC

C401

0.1u

R16

3*

2SK3077FQ210

R46

47k

R229

150k(D)

C116

0.01u

Q605UM6K1N

L2

X100L77-3013-05

1 VC

2 GND 3oUTPUT

4VCC

C66

410

0p

R306

100k

R565

1M

L108

220n

C143

470p

C474

0.1u

C220

470p

D45

5

1SS

388F

SSM3K15TE(F)Q603

R223

47k

R347

1k

L604

R317*

SSM3K15TE(F)Q208

R61

2

1k

C51

7

2700

p

C11

8

470p

IC1MM1522XURE

1NC

2GND

4VOUT

3VCC

C381

0.01u

CN601

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

TC7WU04FK-FIC455

11A

23Y

32A

4GND

52Y

63A

71Y

8VCC

C63

5

100p

C404

0.1u

C282*

R587

1k

C465

0.1u

L611

CP

16

47K

R59

470k

R581 47

C47

3

470p

L4

C38

8

0.01

u

R617

470

R62

2

470k

L7

R47

9

470k

C39

1

82p

C386

8p

IC307TC7W53FK(F)

1CoMMoN

2INH

3VEE

4GND

5 A

6 CH1

7 CH0

8 VCC

C477

0.1u

C16

3*

C1605p

R62

100k

C52

0

0.01

u

Q601SSM6L05FU

R131

1.2k

R641

470k

R55

6

33k

C306*

R53

9

10

D119DA221

R55

100

C67

7

0.1u

L312

*

R362

2.7k

CN606

1 DSR

2 E

3 RXD

4 TXD

5 5M

6 RTS1

7 REM

8 PTT

9 MICE

10 EMC

11 MSW/CTS

12 SP-

13 SP+

14 SSW

IC459TC75W51FK(F)

1

2

3

4 5

6

7

8

C271

470p

R15

9*

Q205EMD9

D453RB706F-40

C50

9

4.7u

R242*

R41

100

C46

6

1u

C17

7*

C33

8

470p

R14

6

220

C47

2

0.1u

C60

3

470p

2SA1832(GR)FQ451

C61

51u

R68

410

0k

C318

470p

R339

0

C32

3

470p

R488

10k

R639 1k

L214 4T

R687

0

C52

2

0.01

u

R528 1k

15V(Y)

R14

5

100k

R686

470k

C16

7

470p

C61

910

0p

R21

4*

L121

220n

C21

9

0.01

u

R23

0

33k

L215

4T

C31

3

470p

C289*

R71

47k

C18

7*

C505

10u

CP

247

0K

R24

327

0

C50

1

100p

C23

9

470p

C450

1u

IC610TK11250CUCB

1NP

2GND

3CoNT

4VIN

6VoUT

SSM3K15TE(F)Q459

D60

2

AV

RM

1005

C27

0M

IC304TA31137FNG

1 oSCIN

2 oSCOUT

3 VCC1

4 MIXoUT

5 VCC2

6 IF1IN

7 DEC1

8 IF1oUT

9 NDPS

10 IF2IN

11 DEC2

12 GND2 13IF2oUT

14QUAD

15AFoUT

16N-REC

17FILIN

18FILoUT

19N-DET

20C-DET

21RSSI

22VREF

23GND1

24MIXIN

2SC5108(Y)FQ109

R30

5

47k

C149*

*

R12

2

3.9k

C354

470p

L605

CP101

1K

D11

8M

A2S

111-

F

R49

6

4.7k

C22

3

470p

2SC4738(GR)FQ450

R46

2

33k

R538

47k

C33

9*

R148

22

R75 47k

R463

2.2k

D10

7

1SV

282-

F

C65

710

0p

IC451TC75W51FK(F)

1

2

3

4 5

6

7

8

R61

1

1k

R31

0

1M

C26

6*

IC201TA75W01FUF

1oUT1

2IN1-

3IN1+

4VEE

5IN2+

6IN2-

7oUT-B

8VCC

C64

9

0.1u

R25

2

18k

C42

3

6p

R225

150k(D)

C14

0

0.04

7u35

C26

0*

L306

*

C362*

C48

4

0.1u

L115*

C11

4

0.1u

C307*

R119

1k

C22

5*

C267

1p

R771M

R56 100

R533 100k

C26

1*

R17

120k

C182

470p

D30

5

1SV

286F

R17

4*

R140

47k

R52

2

47k

CP7 1K

C34

0.01

u

C26

3*

C361

470p

R16

0*

C38

0

0.01

u

C66

810

0p

28MB(Y)

C46

2

470p

C61

4

1u

C5381u

C26

5*

C13

7

100p

C18

9*

R14

470k

C10

1

0.1u

C303

0.1u

L201

*

IC454AK4550VTP

1VCoM

2AINR

3AINL

4VSS

5VDD

6DEM0

7DEM1

8SDTo

9

SDTI

10

LRCK

11

MCLK

12

SCLK

13

PWAD

14

PWDA

15

AoUTL

16

AoUTR

0.1u

C65

0

R22

1*

15D(Y)

C25

90.

01u

R144

1k

R51

847

R15

6*

L102

10u

R60

5

0

L314

18n

C25

847

0p

C23

8

1u

R22

8

10k

L221

3T

C63

7

470p

C129

0.01u

R23

100k

(D)

R112

10

C54

2

0.1u

R20

0

3.3k

R16

4

10k

CF301L72-1009-05

P25

C51

1

0.01

u

2SC5108(Y)FQ303

R357

56k

R56

2

150k

L118

*

R18 10

R45

100

C536

1u

CP4 100

R22

00.

22

L105

220n

R37

2

47

R459

10k

C15

0.1u

R11

3

470k

IC4S-80930CNNB-G

1VSS

2VDD

4 oUT

3 CD

R51

5

0

L227*

R12

9

1.2k

D104

1SV282-F

R506

10

D113*L9

R17

3

10M

3SK318Q301

C25

6*

R177

100k

C31

24p

R263

8.2k

R49

100

C350.01u

L219 4T

C393

0.1u

CF302L72-1021-05

NARROW

C64

1

0.1u

C65

310

0p

R51

470k

R675*

L610

2SK879(Y)FQ103

C25

4

470p

IC600XC6204B502PR

1NC

2VSS

3CE

4VIN

5VoUT

R529 10k

R53

7

33k

C66

910

0p

IC456TC75W51FK(F)

1

2

3

45

6

7

8

CP9 100

C278*

C25

0*

CN609

2oPT3

1oPT1

4TXD1

3RXD1

6oPT4

5NC

8OPT5

7USEL

10AGND

9DGND

12Ao

11AI

145A

13AGND

16DI/ANI

15SToN

18MAN DoWN

17TCoNT

20oPT2

19INH

22RXEo

21TXo

24TXI

23RXEI

26SB2

25oPT6

R46

0

470

R60

347

0k

C63

3

470p

D11

5

1SV

278F

C207

7p

CN613*1

LCS2

GND3

DO4

D15

D26

D37

D48

D59

D610

D711

RD12

WR13

GND14

AO

R39

470

R48

5

4.7k

R659 1k

IC602TC7W53FK(F)

1 CoMMoN

2 INH

3 VEE

4 GND 5A

6CH1

7CH0

8VCC

R59

3

10k

C31

7*

2SK1215-E(E)Q302

R234

10k

R666 1k

R149

150k

R473

0

C17

8

470p

C24

6

0.01

u

R23

6

47k

R580

10

R50

947

D114*

R56

1

33k

R577

47k

R60

81M

D11

1

1SV

282-

F

C18

6

1u

C642 0.1u

C37

9

0.01

u

L120

220n

L200* C22

1

15p

R55

947

L212C292*

C464

0.1u

SSM3K15TE(F)Q452

L303

*

R32

2

270

C12

6

0.1u

C46

7

1u

C13

8

100p

R45

6

150k

R330

0

C48

3

10u

R32

5

270

C62

010

0p

R31

210

0k

R579

100k

R567

100k

C531

0.1u

R51

6

56k

C38

2

0.01

u

C480

0.01u

32kout

D60

0

1SR

154-

400

R649

3.9k

D200

HVC131

C28

0

470pC

232

*

D109

1SV282-F

R661 1k

R32

4

270

C374

27p

D45

4

1SS

388F

2SC5108(Y)FQ111

C60

8

10u

R545

47k

R32

0

100k

R16

470k

R672*

C11

5

0.1u

C29

0*

L12

R62

6

47k

C64

6

0.1u

C20

0.1u

SSM3K15TE(F)Q461

C22

0.1u

C13

5

0.01

u

R688

0

C47

0

150p

R69

0

330

CP11 100

R59

2

1k

R35

47k

C24

4*

CN205

R12

5

1.2k

L128

*

C499

0.1u

L104

220n

C385

47p

R11

0

100k

C644

0.1u

C46

8

0.1u

C5370.1u

L612

C40

8

0.1u

D30

4

1SV

286F

C31

6*

C64

0

470p

CN612

1 GND2GND

3 MIC4MICE

5 SP+6PWR

7 SP+815V

9 SP-10SB1

11 SP-12+B

13 AF14+B

15 VoL16+B

17 CLK18+B

19 GND20LRST

21 KIN2228M

23 EXAFC24PSW

25 KES26INAFC

27 DAT28EXSW

29 TGL03033M

31 TGL23233M

33 TGL13433A

35 CH_A3633A

37 CH_B3825D

39 CH_C4015D

41 CH_D4215D

43 PTT445M

45 NC465M

47 oE48LCDV

49 DGND50DGND

R16

722

0

L107

R60

7

470k

CLKC

R66

100k

R340

8.2k

C41

5

1000

p

C49

3

0.22

u

C61

2

470p

R50

8

10k

C38

0.01u

L119

*

C17

9

470p

R44

100

R25

1

100k

C18

4

470p

R34

9

22

CP6 1K

R20

3

33

C169*

IC101ADF4111BCP7

1CPGND

2AGND

3AGND

4RFinB

5RFinA

6A

VD

D

7A

VD

D

8R

EF

in

9D

GN

D

10D

GN

D

11 CE

12 CLK

13 DATA

14 LE

15 MUXoUT

16D

VD

D

17D

VD

D

18V

p

19R

set

20C

P

C283*

L126

*

C66

110

0p

C29

0.01

u

R258

2.7k

2SJ347FQ108

L600

C66

510

0p

R54

4

10

R249*C12

2

47p

L310

*

CP100

1K

C60

747

0p

IC306TC7W53FK(F)

1 CoMMoN

2 INH

3 VEE

4 GND 5A

6CH1

7CH0

8VCC

D30

7

1SV

286F

R524

47k

L10

R73 47k

IC2RV5C386A

132KOUT

2SCL

3SDA

4INTRB

5VSS

6INTRA

7CLKC

8OSCOUT

9OSCIN

10VDD

R47

6

470k

R484

47

R341

47

C410

39p

L111

220n

C23

0

470p

R22

7

22

C10

3

47p

C285

470p

D30

8

HV

C13

1

C61

6

1u

R136*

C202*

R23

9

100k

C2

0.01

u

C357*

IC460TC7W66FK-F

1 IN_oUT12 oUT_IN1

3 CoNT24

GND5

IN_oUT2

6

oUT_IN2

7CoNT1

8VCC

C41

6

0.1u

R65

3

10

L100

R49

1

2.7k

C26

0.01

u

R525

180k

C370

0.01u

L123*

R130

100k

R15

8*

C12

847

p

R47

4

120k

D30

1

1SV

286F

R621 100k

C11

7

0.01

u

C14

7

4.7u

R155*

R49

8

22

C34

7*

C10

8

0.1u

C36

3

470p

C24

7

470p

IC200TC75W51FK(F)

1

2

3

4 5

6

7

8

C49

7

10u

R15100k

R56

0

100k

2SJ347FQ455

RF ANT(Y)

L222

L127

10n

XF300L71-0551-45

2SJ347FQ454

R20

1*

R17

5*

R493

4.7

TH

200

B57

331V

2104

J

R60

1

470k R680*

R33

7

47

CV

R642 470k

L308*

C360

470p

Q110*

R64

7

100k

C32

2

470p

C209

470p

X1L77-1802-05

R564

1M

R638 1k

C14

8

470p

D203HVC131

C33

7*

C387

470p

Q602SSM6L05FU

R74 47k

R59

7

100k

D611NNCD6.8G-A

C38

3

22p

R674*

R24

627

0

R648

3.9k

L223

820n

L122

R628 47

C175*

R11

718

k

R48

0

47k

C330

470p

C16

5

4p

R308

10k

C24

3*

R643 470k

R48

3

10k

R61

5

1k

L300

*

BATT+B(Y)

R505

10

C27

0.01

u

R685

470k

C35

2*

R6520

C61

7

1u

C45

1

100p

TPC6108-FQ604

IC202 MASWSS0181

1RF1

2GND

3RF2

4V2

5RFC

6V1

L109

220n

L112

220n

R16

6

330

C24

9

0.1u

C471

150p

L13

R11

1

100

R635 0

D30

6

1SV

286F

C403

0.1u

R519

47

C25

5*

C16

8

470p

C311*

L203

* L304*

C47

8

4.7u

C62

910

0p

TC7W66FK-FIC450

1 IN_oUT1

2 oUT_IN1

3 CoNT2

4 GND 5IN_oUT2

6oUT_IN2

7CoNT1

8VCC R

634

10k

C349

2p

L225*

2SJ243-AQ209

R468

33k

5M(Y)

C183

470p

C47

9

4.7u

3.9k

R644

R47

5

33k

R35

6

15k

R11

6

47k

C188

470p

IC302SPM5001

1G12D13D24 S2

5 S1

6 G2

C412

150p

C458

1u

C52

3

0.01

u

L124

18n

IC603TC74VHCT244AFT

11G

21A1

32Y4

41A2

52Y3

61A3

72Y2

81A4

92Y1

10GND

112A1

121Y4

132A2

141Y3

152A3

161Y2

172A4

181Y1

192G

20VCC

R48

9

100k

D30

2

1SV

286F

R49

9

3.3k

R370

47

R48

2

100k

CP

14

47k

D45

2

MA

2S11

1-F

R16

5*

R46

7

470k

R215*

L601

L603

C45

2

100p

R63

47k

R15

3

100

C62

3

100p

R22

220k

(D)

R629 10k

R32

8

10

R32

1

100k

R550 1M

CP3 100

R176

0

R59

6

120k

R50

3

10

R36

0

3.9k

C21

5

470p

R11

5

10

C62

533

00p

C643 0.1u

R517

47

L452

C34

5

470p

IC305TC7W53FK(F)

1CoMMoN

2INH

3VEE

4GND

5 A

6 CH1

7 CH0

8 VCC

C60

4

470p

R26

2

2.2k

C161 5p

C34

4*

C39

7

68pR34

2

680k

L8

CP

147

k

R50

100

C32

9

470p

C130

47p

R264

0

R32

6

2.2k

C46

9

0.1u

Q207DTA144EE

R11

83.

3k

IC303TC7W53FK(F)

1 CoMMoN

2 INH

3 VEE

4 GND 5A

6CH1

7CH0

8VCC

R15

1

56

C17

3*

Q304EMD9

R1240

C65

110

0p

2SK508NV(K52)Q106

IC604TC7SBD384AFU

1A

2B

3G

ND

4oE

5V

CC

C12

470p

C20

4*

R46

1

390k

R571

100k

C45

6

2.2u

R14

7*

C16

4*

IC6

A1

A3

A2

A7

A3

RY

/BY

A4

WE

A5

A9

A6

A13

B1

A4

B2

A17

B3

VP

P

B4

RE

SE

T

B5

A8

B6

A12

C1A2

C2A6

C3A18

C4NC

C5A10

C6A14

D1A1

D2A5

D3NC3

D4A19

D5A11

D6A15

E1

A0

E2

DQ

0

E3

DQ

2

E4

DQ

5

E5

DQ

7

E6

A16

F1

CE

F2

DQ

8

F3

DQ

10

F4

DQ

12

F5

DQ

14

F6

BY

TE

G1oE

G2DQ9

G3DQ11

G4VCC

G5DQ13

G6DQ15/A-1

H1VSS1

H2DQ1

H3DQ3

H4DQ4

H5DQ6

H6VSS2

BEEPS

TCNT

AUXI

INH

KEY_PLAY

LCDV

CLK

BSFT

LE

BEEP

LD

PSW

CPUCLK

RESET28M 33M

STRB

CLK

SDA

UL

oE

DAT

RESET

T/R

TEMP

SDA

CLK

oP_T

XD

1

RX

D1

BU

SY

RT

S

CT

SM

DS

RM

RX

DM

TX

DM

A20

KE

Y1

RD

Y

KE

S

VN

WN

EX

TIM

SC

SW

R

CS1

CS2

LCS

A17

A18

A19

CS0

A14

A15

A16

A11

A12

A13

A10

CHD

CHA

INAFC

A9

CHC

CHB

WR

RD

TG

L0

TG

L1

TG

L2

A8

A4

A3

A2

A1

A0

EXAFC

HINT

A7

A6

A5

PTT

+B

33M SB

33M

TE

MP

RE

M

VoL

RS

SI

PW

R

WPASQ

MM

5CC

D0

D1

D2

D3

D4

D5

D6

D7

AP

CS

W

5TC

5RC

EX

SP

DR

ST

FR

ST

BAT

TD

ET

D1

D6

D3

D4

A0

RD D0

D7

FC

S

A1

D2

D5

A17

A15

A6

A12

A20

A2

A16

A11

A19

A7

A3

C23

0.01

u

IC7TC7S08FU-F

1INB

2INA

3GND

4oUTY

5VCC

L11CS0

FCS

CS2

33M

33M

EM

U0

EM

U1

D6

D5

WR

RD

D4

33A

15D

SRESET

BFSX1

SDTI

LRCK

SCLK

SDTo

LRCK

SCLK

CS

SD

o

BIo

CS

1

A0

D7

CT

S

PT

T

EX

SP

RE

M

RX

D

DS

R

5MC

S

5M

TXDM

DAT

CLK

STRB1

RTS

oE1

LD1

EXTI

CHGIo

oE

DAT1

LD

STRB

CLK1

5M

33M

MU

XoU

T

D_TXD

IC461TC75S51FE(F)

1IN+

2VSS

3IN-

4oUT

5VDD

L627

L628

L625

L626

L623

L624

L622

L629

L620

L621

L618

L619

L616

L617

R632

0

L210

*

X300L77-1961-05

oUTPUT3

VCC41 VC

2 GND

ANT

SToN

RXEo

oPT4

TCoNT

oPT2

C3

TXI

SB2

DGND

AGND

TXo

oPT3

AGND

oPT5

MAN DoWN

INH

RXEI

DI/ANI

5A

oPT1

S901

D901B30-2019-05

CN902

36M 1

S36M 2

GND 3

VoL 4

33M 5

CH_A 6

TGL2 7

TGL1 8

C 9

CH_B 10

CH_D 11

CH_C 12S902

CN903

1 GND

2 CH_A

3 CH_B

4 CH_C

5 CH_D

6 36M

7 S36M

8 33M

9 TGL0

10 TGL1

11 TGL2

12 BLED

13 TXLED

14 ORG

15 VoL

16 KIN

17 GND

5M

CH_B

L_MIC

CH_A

5M

PSW

+B(Y)

TGL1

D7

TGL2

L_KEY1

D4

TGL0

CLK

CH_B

33A

L_MIC

VoL

PF1

DAT

CH_A

LCDV

D5

D6

15D

L_PTT

LRST

PF2

KE

S

5AC

D2

GND(Y)

15V

D6

D0

L_PTTG

25D

L_KEY1

L_PTT

PF3

oE

5M

33M

33M

D5

D0

D3

CH_C

PF2

PF1

36M

D7

WR

TGL2

D1

PF3

D1

VoL

TGL1

L_KEY1

A0

key*

33A

L_PTTG

33M

key#

LCS

key6

15D

PWR

D2

15V

PT

T

DAT

LCDV

key8keyB

15V

KIN

5AC

KES

oE

D3

keyA

SB1

KIN

key0

PTT

keyC

D4

CLK

key9

5M

A0

WR

5M

keyD

TGL0

MICE

key5

LCS

key1

CH_D

CH_DPOWER(Y)

key3

LRS

T

key2

MICE

CH_C

key4

PS

W

key7

L707

CN800* 14LCS

13GND

12DO

11D1

10D2

9D3

8D4

7D5

6D6

5D7

4RD

3WR

2GND

1AO

CN700

2GND 1 GND

4MICE 3 MIC

6PWR 5 SP+

815V 7 SP+

10SB1 9 SP-

12+B 11 SP-

14+B 13 AF

16+B 15 VoL

18+B 17 CLK

20LRST 19 GND

2228M 21 KIN

24PSW 23 EXAFC

26INAFC 25 KES

28ECSW 27 DAT

3033M 29 TGL0

3233M 31 TGL2

3433A 33 TGL1

3633A 35 CH_A

3825D 37 CH_B

4015D 39 CH_C

4215D 41 CH_D

445M 43 PTT

465M 45 36MD

48LCDV 47 oE

50DGND 49 DGND

D70

8

MA

2S11

1-F

C78

8

10u

R70

1

1k

C70

2

10u

C70

4

10u

C700

0.1u

R70

2

100k

SSM3K15TE(F)Q700

R70

5

1k

R710

33k

R708

2.7k

Q701UMG3N

R7111.2k

2SB798(DL,DK)Q702

L700

SSM3K15TE(F)Q703

2SJ243-AQ704

R713

1M

R709

47

C70

3

470p

C70

1

470p

IC800*1 OUTPUT

2 V+

3 INPUT+ 4INPUT-

5V-L801*

R801*

C80

8*

C84

2*

R80

6*

R805*

C814*

R80

4*

C80

1* C

803

*C80

2*C

800

* C80

5*

R813*

key4

keyA

R815*

key0

R810*

keyD

key5

R808*

R819* key7

R807*

key2

R816*

R809*

key#

R812*

keyB

key3

R814*

R811*

key9

R821*

key1

keyC

R820*

key6

R817*R818*

key*

key8

R822*

CN802*1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

L800

* C80

7*

LCD(Y) C810*C811*

C809*

C81

2* R

823

* R82

4* C

825

* R82

8*

R82

7*

S800 S805 S810 S815

S804

S802

S801

S803

S806

S809

S808

S807

S811

S812

S813

S814

IC701TC7W66FK-F

1IN_oUT1

2oUT_IN1

3CoNT2

4GND

5

IN_oUT2

6

oUT_IN2

7

CoNT1

8

VCC

IC702LM4906LD

1SHUTDoWN

2GND1

3GAIN_SELECT

4INPUT

5NC1

6

NC2

7

Vo1

8

VDD

9

GND2

10

Vo2C707

0.1u

R71

9

47

R72

0

1M

C708

1u

R7181M

SSM3K15TE(F)Q705

2SJ243-AQ706

D70

0

1SS

388F

L701

L702

L703

L704

C71

6

0.1u

C71

8

470p

C71

2

2.2u

R72

2

1k

R72

3

100k

IC703LM4906LD

1SHUTDoWN

2GND1

3GAIN_SELECT

4INPUT

5NC1

6NC2

7Vo1

8

VDD

9GND2

10Vo2

R72

1

1M

C7091u

C71

3

2.2u

C71

9

470p

C71

7

0.1u

D71

1

AV

RM

1005

C27

0M

D71

0

AV

RM

1005

C27

0M

C72

4

1u

R72

6

0

SSM3K15TE(F)Q708

R72

8

2.2k

R729

22k

C726

0.1u

C72

8

100p

R73

4

180k

R73

3

150k

C72

7

2.2u

R732

150k

R731

680k

28M(Y)

D701

1SS388F

C72

5

1u

C79

5

1u

R735

33

R730

1k

CN702

J19-5386-05

IC704XC6204B302M

1VIN

2VSS

3CE

4NC

5VoUT

CN8031

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

R841 1k

R784

470k

R79

8

470k

IC706XC61CC5602NR

1VoUT

2

VIN

4 VSS

3NC

R748

10k

Q713UM6K1N

C74

0

470p

C72

9

0.1u

C73

1

0.1u

R737

47

R74

7

1.8k

C73

0

0.47

u

R74

3

22k

R744

22k

C737

0.47u

R73

8

27k C73

6

0.47

u

R741

47k

R739

22k

C73

2

0.02

2u

R74

2

1.8k

R746

47k

R74

5

47k

C73

8

470p

C73

4

470p

Q709UMC4N

D702NNCD6.8G-A

C73

947

0p

IC705TC75W51FK(F)

1

2

3

4 5

6

7

8

D805*

D804*

IC801BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9QS

10Q’S

11Q8

12Q7

13Q6

14Q5

15OE

16VDD

C82

6

0.01

u

D81

3*

L803

D814*D816*

IC802BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9QS

10Q’S

11Q8

12Q7

13Q6

14Q5

15OE

16VDD

C82

9

0.01

u

D81

7IM

N10

D81

8IM

N10

IC803BU4094BCFV

1STRB

2DATA

3CLK

4Q1

5Q2

6Q3

7Q4

8VSS

9QS

10Q’S

11Q8

12Q7

13Q6

14Q5

15OE

16VDD

C84

0

0.01

u

R849 1k

R847 1k

R850 1k

R851*

R855 1k

R859 1k

R860 1k

R852 1k

R856 1k

R858 1k

R857 1k

*R82

6

R82

5* R

829

* R83

0*

D80

0* D

802

*

D80

6* D

808

*

D80

7*

D80

3*D

801

*

R83

1* R

832

* R83

3*

D81

0* D

811

* D81

2*

C827*

R83

5* R

836

*

Q800*D815*

C82

8*

Q801*

CN7131

2

3

4

5

6

C78

5

470p

L708

L709

C78

4

470p

C78

3

470p

L705

C741

470p

C74

54.

7u

C74

64.

7u

C742 4.7u

C743 4.7u

TPC6108-FQ710

36V(Y)

D704HRB0502A

IC710XC6365D103M

1 EXIT/

2VDD

3GND

4CE

5

VOUT/FB

R77

2

330k

C76

4

82p

C77

50.

1u

C77

633

u10

R77

0

220k

C76

3

0.1u

R77

3

120k

R790

10k

C74

4

0.01

u

D7031SS301F

L804

L805

C831 4700p

C830 4700p

C832 4700p

C833 4700p

C834 4700p

C837 4700p

C838 4700p

C835 4700p

C836 4700p

R844 470

R854 470

C84

1

4700

p

R848 1k

CN804

1

2

3

4

5

6

Q804SSM6L05FU

Q803SSM6L05FU

R84

5

470k

R85

3

470k

R84

6

470k

R84

3

470k

SSM3K15TE(F)Q802

R839

1kR842

100k

R84

0

470k

D705DA221

D706DA221

D70

7C

US

01

33M(Y)

C76

2

470p

C76

9

1u

IC707XC6204B332M

1VIN

2VSS

3CE

4NC

5VOUT

C74

9

0.1u

R758

2.2

IC708XC6204B332M

1VIN

2VSS

3CE

4NC

5VOUT

C76

0

470p

C76

5

1u

33A(Y)

C75

0

0.1u

R759

2.2

C75

4

0.01

u

Q712UM6K1N

R79

710

0k

R79

610

0k

IC709XC9225A15CM

1 VIN

2 VSS

3 CE/MoDE 4VoUT

5LX

15D(Y)

L807

C76

1

470p

C76

6

4.7u

IC712TK11250CUCB

1NP

2GND

3CoNT

4VIN

6VoUT

C77

0

470p

C77

4

1u

5M(Y)

5M

C75

3

1u

IC711XC6204B252M

1VIN

2VSS

3CE

4NC

5VOUT

C76

8

470p

C77

3

1u

25D(Y)

C75

7

0.01

uC74

7

0.1u

R753

2.2

25D

SB(Y)C79

0

470p

C75

1

4.7u

IC713XC9101D09AKR

1 EXT

2 LSEN

3 VIN

4 CE/SS 5CLK

6CC/GAIN

7VoUT/FB

8VSS

R77

112

k

C76

718

0p

C77

247

0p

R77

522

kR

774

330k

C77

122

p

C77

91u

C77

71u

C77

81u

15V(Y)

Q711SSM5H01TU

L706

68u

SB

1

C75

90.

1u

R768

150k

C75

21u

C75

54.

7u

R762

10

C74

81u

R754

33

PW

R

33M

33A

33M

CN923

2

1

4

3

6

5

8

7

10

9

12

11

14

13

16

15

18

17

20

19

22

21

24

23

2625

R70

6

330

L802

*

D80

9*

SCLK1

BATTDET

ASSIST

BEEP

ASSIST

DS

PC

LK D3

DR

ST

EM

U1

EM

U0

D2

D1

A1

BDX2

D0

BDX1

INT0

RDY

BFSX2

HINT

BDR2

BCLKX2

A2

BCLKR2

BFSR2

A3

A18

A10

A8

WR

A9

A4

A13

A14

A5

FR

ST

5M

33M

MM

VATS

33A

C453

0.1u

5M

33A

5R SQ

33M

TX

I

SC

SW

T

SC

SW

R

33A

TX

o

5M

BF

SX

1

LRC

KS

DT

I

SD

To

SC

LKM

CLK

BE

EP

S

33A

33A

RX

Eo

SC

SW

R

RX

EI

MC

LK

CPUCLK

BSFT

DSPCLK

TU

NE

2

5M5M

CLK

1

LD1

L2S

F

DAT

1

33A VC

TU

NE

AP

C

33A

VA

RS

Ao

AIBE

EP

Ao

AI_TX

LRST

ECSW

VATS

5MC

STRB

VARS

CS

SD

o

UN

_DAT

SR

ES

ET

IF_I

N

CLK

SC

LK1

oE

TCoNT

EXTIM

DSR

CTS

EXTI

RXD

oP_INH

BUSY

oPT4

DAT1

CLK1

oPT1

STRB1

oP_MAN

oPT5

oE1

UN_DAT

CHGIo

oPT6

oPT2

oPT3

oPT1

33M 5M

25D

oPT

3

oPT

2

33M

KE

Y_P

LAY

AU

XI

RX

DM

TC

NT

INH

DS

RM

CT

SM

33M

STo

N

PWR

+B

SB

15V

5MCS

S33A5M

VC

LE

DATCLK

5C

S33A

UL

MUXoUT

S33A

5R

5CC

33A

5T

5MC

5CC

PWR

5TC

5RC

TUNE

15V

TUNE2

5C

33A

5R

R13

9

470k

S33

A

S33

A

5C 5R 5TT/R

R150

100

5C

5R

VN 33

A

33A

IF_I

N

RS

SI

5R

L2S

F

5T AP

CS

W

5M +B

AP

CS

W

AP

C

5T 5M 5M5TWPA

BFSX1

BDX2

36MD

INT0

BCLKX2

BCLKR2

BFSR2

BFSX2

BDR2

33M

D_TXD

RXDM

BDX1

5M

5M

SB

33M

oP_MAN

TXo

SToN

Ao

AI_TX

oPT2

oPT4

oPT5

RXEo

TCoNT

AI

RXEI

TXI

oPT6

oP_INH

RXD1

oPT1

oP_TXD1

oPT3

L609

L608

R23

7

180k

WN

D4

LCS

A0

D6

D7

D1

WR

D2

D0

D5

D3

PTT

INAFC

PWR

DAT

CHB

KEY1

KESECSW

CHA

CHC

LCDV

EXAFC

VoL

oE

CLK

TGL2

TGL0

PSW

LRST

TGL1

CHD5M

36MD

15D

25D

33A

15V

28M

SB

33M

+B

L615

5M

L614

EEPROM

VCXO

TEMPCOMPENSATION(FOR PA)

INT SP

S

MIC MUTE SW

VGS I/O SW

SW(VGS TX I/O)

EXT MIC SW

BUFFERD-TYPE FLIP FLOP

TX SCRAMBLER SW

RX VCO

TX VCO

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

TX-RX UNIT :ANT SECTION(X57-7250-XX)(E/5)

SIDE KEY SECTION

NC MIC

* LCD

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

CONCENTRICSW

POWER SW/AF VOL

CHANNELSELECTOR

TX-RX UNIT :TOP SECTION(X57-7250-XX)(C/5)

REVERSECURRENTPREVENTION

D1

SURGEABSORPTION

D601,602

SURGEABSORPTION

SURGEABSORPTION

REVERSECURRENTPREVENTION

DETECTION

DETECTION

DETECTION

LOCAL SW

LOCAL SW

ANTENNA SW

D202,203

ANTENNA SW

VARI-CAPTUNE

D301,302

D106,107,110,111,112

FREQUENCY CONTROL

D102,104,105,108,109

FREQUENCY CONTROL

RIPPLE FILTER

BYPASSDIODE

5V 3.3VLEVEL CONVERTER

W/N SW

T/R SW

SW

5T SW

5M SW

AUTO GAIN CONTROL

Q450,451

RF AMP

RF AMP

APC SW

RF DRIVE AMP

RF FINAL AMP

RIPPLEFILTER

IF AMP

BUFFER for CV

RIPPLE FILTER

VCOOSCILLATION

BUFFER AMP

NOISE AMP

RTC IC

VOLTAGE DET

TEMPERATURE DET

CPU

FLASH ROM

CS AND

DSP

BUFFER

MULTIPLEXER

SHIFT REGISTER

FPGA

AUTO POWER CONTROL

SPDT

DC AMP

DC AMP for BPF

MULTIPLEXER

FM IC

BUFFER

DC AMP for VCO TUNE

PLL IC

OP AMP(5V REFERENCE/BUFFER AMP)

CODEC

OP AMP(TX LPF/RX LPF)

D/A CONVERTER

BUS SW(8ch)

UART SWTX/RX LED

MULTIPLEXERMULTIPLEXER

VCOOSCILLATION

BEET SHIFT SW

POWER

CPUCPU

POWER

CPU

POWERPOWER

CPU

CPUCPU

DSP-FPGA

DS

P-F

PG

A

POWERPOWER

CPU

POWER

DSP-FPGADSP-FPGA

CPU

POWER

CPU

POWER

CPU

OPTION OPTION OPTIONOPTION

POWER

CPU

POWER

CPU

OPTION OPTION

CPU CPUCPU

OPTIONOPTION OPTION OPTION

CPU CPU CPUCPU

POWER

PO

WE

R

CP

U

CPU

CPU

POWER POWER

CPU CPUCPU

POWERPOWER

POWER POWER POWER POWER POWERPOWER

POWER

CPU

EMCMICE

MIC

EE

MC

CTS

CT

S

SP+SP-

SP

+S

P-

MICE

SP+SP-

SP+

MICE

SP-SP+

MICE

SP- SP-

MICE

SP+ SP+

MICE

SP- SP-

MICE

SP+ SP+

MICE

SP- SP-

MICE

SP+ SP+

MICE

SP- SP-

MICE

SP+ SP+

MICE

SP- SP-

MICE

SP+

CVCV CVCV CVCV

CVCV CV

VOLTAGEPROTECTION

MIC MIC

OPTION

OPTIONOPTION

OPTION

MIC MICMIC MIC MIC MIC MIC MIC MIC MIC

VCXO

T/R

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

TUNE 1

5R5R

+B +B

INT MIC(MAIN)

CPUCPU

CPU

V4

V3

V2

V1

V0

VR

NC

GN

D

NC

GN

D

VD

D

D7

Vou

t

NC

NC

NC

NC

NC

D6

D5

D4

D3

D2

D0

D1

A0

LRS

T

E/R

D

WR

LCS

NO

R836

D807

NO

D800

100p

R851

B30-2261-05

100

2.2k

B30-2171-05

NO

1k

1k

R830

D803

C827R825

NO

B30-2171-05

R829

NO

0.1u

R826

B30-2171-05

NO

100

1k B30-2171-05

D806D802

100

R835

100 100

NO

0.1u2SB798(DL,DK)

D810

NO

NO

470k

NO

1k

R807 D801

2SC4617(S)

NO

2SC4617(S)

NO

100

Q800

NO

NO

NO

D814

NO

Q801

NO

D808

IMN10

NO

NO

R832

180

NO

NO

B30-2171-05

180

2SB798(DL,DK)

NO

C828

100p470k

B30-2261-05

NO

B30-2171-05

B30-2171-05 NO

NO NO

2.2k

NO

NO

B30-2171-05

NO

YES

NO

D804

E40-6337-05

NO

IMN10

LCD

E40-6337-05

IMN10

CN802

YES

NO

C812C800

NO

0.47u

0.47u

R808

1k

1k

NO

NO

22k

22k

R823

NO

R827

22k 470p

470p

NO

C807 C809

NO

1u

1u

C810

NO

1u

1u

C811

NO

1u

1u

R809

1k

NO

1k

NO

L92-0446-05

L800

L92-0446-05 L92-0446-05

L92-0446-05

NO

L802

R824

22k

NO

22k

D805

NO

IMN10

IMN10

D813

NO

IMN10

NO

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

0.47u

C801

NO

0.47u

0.47u

C802

NO

0.47u

0.47u

C803

NO

0.47u

0.01u

C805

NO

0.01u

C825

470p

470p

NO

K2,K5-11,-14

K3,K6

-10,-13

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

-12,-15

K,K4

X57-7250-XX

470p

CN800

NO

R805

0

R801

E41-1634-05

10M

E41-1634-05

R806

33k

C808R804

NO NO

100k

NO

NONO

0.01u0

NO

L92-0446-05

10M

IC800

C814

LMC7101BIM5

33k 470p

LMC7101BIM5

NO

100k

L92-0446-05

L801

0.01u

NO

180

R833

NO

NO

E41-1634-05

CN613

E41-1634-05

R672

100

100

NO

R673

NO

100

100

R674

NO

100

100

R675

NO

100

100

R676

NO

100

100

R677

NO

100

100

R678

NO

100

100 100

R679

NO

100

100

R680

NO

100 100

100

R681

NO

100

100

R682

NO

SW

MIC MUTE

BUFF AMP(MOD)

MIC AMP(with AGC)

SW(VGS RX I/O)VGS I/O SW

RX SUMMING AMP

DSP-FPGA DSP-FPGADSP-FPGA DSP-FPGADSP-FPGA DSP-FPGADSP-FPGA DSP-FPGA

1st Lo 1st Lo

TOP SW SECTION

SIDE 2

SIDE 3

PTT

SIDE 1

EXT ANT

GND

GND

APC

D204,205

2V2V

Tune2_out

TX-RX UNIT :OPTION SECTION(X57-7250-XX)(D/5)

SB2

DI/ANI

DGND

INH

NC

AGND

oPT2

TXo

RXEI

TXI

NC

C3

oPT4

RXEo

TCoNT

AGND

oPT5

SToN

5A

MAN DoWN

AGND

DI/ANI

TXo

NC

TCoNT

INH

MAN DoWN

TXD1

oPT4

NC

TXI

SToN

AGND

oPT1

RXEI

DGND

oPT1

oPT2

C3

oPT5

5ASB2

oPT3

RXD1

oPT3RXEo

MIC

36M

28M

36M

VOLTAGEREGULATOR(28M)

D804,805

VOLTAGEDETECTOR(5.6V)

EXTERNALAUDIO MUTE SW

D817,818

INT SP

DC/DCCONVERTER(15V)

SHIFT REGISTER

LAMP

ECSW

MIC

STRB

33M

MICE

VOLTAGE REGULATOR(33A)

STRB

KIN

(MAIN)

SP+

33M

SP-

GND

BLED

33M

BLED

DC/DC(15V)

INAFC

SWITCH(36M DC/DC)

D705

TXLED TXLED

AUDIO AMP

BUSY LED SW

CLKCLK

oE

MICE

Q704

INTERNALAUDIO MUTE SW

oE

MICE

SHIFT REGISTER

AUDIO AMP

SP-S_EXAFC

DC AMP forLCD VOLTAGE

REVERSECURRENTPREVENTION

S_EXAFC

PSW SW

EXTERNALAUDIO MUTE SW

5M

REVERSECURRENTPREVENTION

5V AVR

DC/DC(3.6V)

+B+B

5M

INAFC

REVERSECURRENTPREVENTION

AF

SHIFT REGISTER

SP+

EXT/INTGAIN CONVERT SW

FLYWHEEL(DC/DC)

NOISECANCELER SW

KINKIN

VOLTAGE REGULATOR(33M)

KEY BACK LIGHT

GND

S36M

AF MUTE SW

33M

S36M

DC/DC CONVERTER(15D)

33A

REVERSECURRENTPREVENTION

KIN

AF

+B

INTERNALAUDIO MUTE SW

MICE

MIC

D800-803,806-809

28M

MIC

INT MIC

SURGEABSORPTION

DATADATA

5V AVR SW

OP AMP(AF PRE-AMP/TX AF AMP)

+B

ECSW

AF

33M

D708

33M

OGR

28M

33M

OGR

ECSW

REVERSECURRENTPREVENTION

D706,707

A

0

B

9

D

2

6

1

5

#

4

8

3

C

7

Li-CELL:W09-0971-05

VOLTAGE DET(UP HARD RESET)

+B +B

+B+B

MIC MIC

DC/DC(1.5V)

MICE MICE

EMC

1

5M

TXD

SSW

REM

MICE

EXT ANT

MSW/CTS

14DSR

RXD

GND

PTT

UN

IVE

RS

AL

CO

NN

EC

TOR

E

GND

SP-

RTS1

SP+

DC/DC CONVERTER(36M)

VOLTAGE REGULATOR(25D)

VOLTAGE REGULATOR(5M)

5VAVRSW

SWITCH(15V DC/DC)

DSPPOWER SUPPLYTIMING CONTROL

DC/DCCONVERTER(36M)CONTROL

SW(BACK LIGHT)

SW(BACK LIGHT)

TX LED SW

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

REVERSECURRENTPREVENTION

D810-812

LCD BACK LIGHT

AVR forBACK LIGHT LED

K3,K6

-10,-13 K,K4

X57-7250-XX

K2,K5

-12,-15

-11,-14

NO

0.022u

C842

0.022u

K3,K6

-10,-13 K,K4

X57-7250-XX

K2,K5

-12,-15

-11,-14

-11,-14

X57-7250-XX

-10,-13 K,K4

K2,K5

K3,K6-12,-15 1k

1k

NO

R810

NO

R811

1k

NO

R812

NO

1k

NO

R813

NO

1k

NO

R814

NO

1k

NO

R815

NO

1k

NO

R816

NO

1k

NO

R817

NO

1k

NO

R818

NO

1k

NO

R819

NO

1k

NO

R820

NO

1k

NO

R821

NO

1k

NO

R822

NO

1k

NO

-11,-14

X57-7250-XX

-10,-13

K3,K6

K,K4

-12,-15

K2,K5

22k

NO

470k

R828

470k 1u

1u

-11,-14

X57-7250-XX

-10,-13 K,K4

K2,K5

K3,K6

TX-RX UNIT :CONTROL SECTION(X57-7250-XX)(B/5)

-12,-15

NO

D816

IMN10

NO

B30-2171-05

NO NO

NO

B30-2171-05

D809

B30-2261-05

B30-2261-05

D811

NO

B30-2261-05

B30-2261-05

D812

NO

K3,K6

X57-7250-XX

-11,-14

-12,-15

K,K4

K2,K5

-10,-13

DTZ3.9(B)

D815

NO

DTZ3.9(B)

R831

NO

180

180NO 180

K,K4

K3,K6

X57-7250-XX

-10,-13

K2,K5-11,-14

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

-12,-15

HVC131

NO

D113

-10,-11,-12

-13,-14,-15

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

X57-7250-XX

K4,K5,K6

K,K2,K3

K4,K5,K6

K,K2,K3

-13,-14,-15

X57-7250-XX

-10,-11,-12

D114

HVC131

NO

D116

HVC131

NO

D117

HVC131

NO

Q110

2SC5108(Y)F

NO

L122

L92-0446-05

NO

Q107

2SK508NV(K52)

2SK508NV(52K) 23n

33n

L115

NO

L118

3.3n

2.7n

L119

1.8n

NO

L123

22n

22n

L125

15n

NO

L126

10n

22n

L128

27n

22n

L315

NO

R136

33k

22k

R141

NO

0

R142

47k

NO

R143

47k

NO

R147

220

270

R155

27

39

R152

NO

22

R156

180

150

R157

47k

NO

150

R160

180

R163

NO

0

R165

10k

NO

R174

NO

270

0

R175

270 39p

C149

15p

1p

C150

0.5p

27p

C151

22p

6p

C156

5p

5p

C157

2p

47p

C158

NO

10p

C162

NO

12p

C163

8p

5p

C164 C169

2p

C173

NO6p 3pNO

9p

C174

6p 4p

C175 C176

2.5p

C177

NONO 4p2p

100p

C180

10p 15p

C189 C190

47p

C187

NO5p NO

47p 470p

NO

C357

15p

470p

C362

NO

L225

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

L210

22n

R214L209 R221

270 270

5p

C218

-10,-11,-12

-13,-14,-15

15n

6p

6.8n 470p

8.2n

L206L200

7p

X57-7250-XX

180

22

R201 R233

18n 7p

1K,K2,K3

39n

C202

18n

NO1.5k

22p

R215

4718015n

1.8kNO

NO

L201 C203

K4,K5,K6

R216 C204

0

18n

18NO

15n

18n

33

L203 C224

39p

27p

C225

NO

470p

C227

470p

NO

C232

NO

22p

C244

470p

NO22p

47100n

22p

27n

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

C332

18p

7p

C344

12p27n

1p

27p56n 82n

120n

27p47p18p

L310 R316

7p

7p

C341

8p

27 10p

27n

L306 C339C337C335C317

18n

7p

C346

47p

7p

1.5p

39p47n

15p

C336L309

-10,-11,-12

C311

3p

5p4p

12p18n

L311

3p18n 27

C342R374L300 C309R313

15p

C307

15p

K4,K5,K6 12p56 22

C347 C352

120

C316

68k

27n

4p22p

27n

22n

27p

C315

-13,-14,-15 18p

56n

27p

C306L308

18n

R317

22p

L312

12p

L303

9p

47k

K,K2,K3

X57-7250-XX

NO

C256C255

100p0

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

C257R242L304

470p4.7n

0

C260

-13,-14,-15 7p

NO

R249L227

15p

9p-10,-11,-12

NO 8.2p

NO

C261

2pNO

4p

K4,K5,K6

C263X57-7250-XX C243

47p

10p

C250

K,K2,K3

10n

2pNO

68p 18p

7p27p 6p

C265 C281

4p

C282

NO 0.5p

6p 15p

9p

15p

C278C268

7p

9p9p

C283C266 C288 C296

3p 8.2p

6p

C289 C290

18p

12p

5p

2.5p

NO5p

2.5p3p

C295

6p

C292

33p

NO

C297

7p

9p

POWER

POWER

CPU

CV

LOOPFILTER

SPDT

TEMP DET

DC AMP for BPF

DBM

MULTIPLEXER

IC451

OP AMP(TX AGC AMP/BUFFER AMP)

Q454,456

SW(RX SCRAMBLER SW/BEEP SW)

OP AMP(TX BUFFER AMP/RX BUFFER AMP)

OP AMP(TX MOD AMP/3.3V REFERENCE)

VOLTAGE REGULATOR(5T/5R)

VOLTAGEREGULATOR(5C)

UART SW

BUS SW(2ch)

BUS SW(2ch)

VOLTAGE REGULATOR(5MCS)

5M SW

S33A SW

T/R SW

BUFFERAMP

BUFFER AMP

BUFFER AMP

APC SW

APC SW

APC SW

SPDT EXT/INT SW

LNA(LOW NOISE AMP)

2ND LOCALBUFFER AMP

EXT MIC SW

5R SW

SB SW

FM MODULATIOND115

FREQUENCYCONTROL

D116,117

FEEDBACKFILTER SW

D113,114

3.3V 5VLEVEL CONVERTER

5C VOLTAGE RISE

D304-307

VARI-CAPTUNE

REVERSECURRENTPREVENTION

SURGEABSORPTION

D609,611

IC452

1st L

o

R158

47k

NO

R159

NO

220k

R15

2

**

R36

6

22

BIo

R70

7

100k

R71

4

100k

TX-RX UNIT :TX-RX SECTION(X57-7250-XX)(A/5)

7.5V

7.5V

3.32V

4.98V

5.0V

7.5V3.32V

R:0VT:3.35V

R:3.32VT:0V

R:4.97VT:0V

R:0VT:4.90V

14.51V 13.75V 7.17V

1.48V

3.3V

3.26V

R:1.90VT:1.68V

1.49V

3.22V

5.0V

14.51V 13.81V

0.53V

1.90V

R:2.38VT:0V

R:0.69VT:0V

R:2.06VT:1.67V

R:1.37VT:0V

R:0.51VT:0V

R:4.92VT:0V

R:4.87VT:0V

3.32V

4.98V 4.27V

R:4.26VT:0V

R:0VT:4.19V

0.75V

3.91V

2.12V 4.73V

1.54V

R:2.42VT:0V

R:0VT:2.40V

R:0VT:0.82V

R:0VT:4.74V

R:0VT:0.86V

T:1.71V(H)1.34V(L)

0.64V

3.26V

T:2.49V(H)1.85V(L)

T:7.2V(H)7.4V(L)

R:0VT:1.60V

R:0VT:0.8V

FM:3.32VP25:0V

P25:0VW:3.18VN:0V

T:7.2V(H)7.4V(L)

14.50V

1.51V

3.3V

2.51V

14.51V

3.76V

3.78V

7.49V

3.32V

4.98V

7.5V

7.43V

3.77V

10.49V

3.73V

3.79V

3.67V

R:0VT:4.94V

TK-5310 SCHEMATIC DIAGRAM

Note : The components marked with a dot () are parts of layer 1.

Page 91: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

86

INTERCONNECTION DIAGRAM

OPT1

CN901

1

OPT3

RXD1

TXD1

NC

OPT4

USEL

OPT5

DGND

AGND

AI

Ao

AGND

5A

26

NC

TXI

5A

SB

OPT2

AGND

NC

RXEI

OPT5

AGND

RXD1

INH

TCoNT

NC

TXo

AGND

OPT3

MAN DOWN

DGND

DI

TXD1

RXEo

OPT1

C3

SToN

OPT4CN609

26

1

STON

oPT6

RXEO

DI/ANI

MAN DOWN

TXO

TCONT

INH

RXEI

OPT2

SB2

TXI

REM

SSW

EMC

CN606 5M

PTT

MSW/CTS E

DSR

RXD

SP+

RTS1

114

141

SP-

MICE

TXD

15v

GND

CN612

LRST

MIC

+B

MICE

GND

+B

+B

SP-

SP-

VoL

SB1

AF

GND

SP+

+B

1

KES

KIN

28M

PSW

50

EXAFC

CLK

INAFC

PWR

SP+

TGL1

EXSW

33A

33M

DAT

TGL2

33M

TGL0

15D

CH_A

PTT

15D

CH_D

33A

CH_B

5M

25D

CH_C

5M

LCDV

36MD

oE

DGND

DGND

15v

50

CH_A

36MD

33M

VoL

33A

KES

MICE

TGL1

1

PWR

+B

DGND

CH_C

33M

TGL2

CH_D

+B

AF

LRST

INAFC

+B

DAT

25D

SP+

SP-

MIC

CN700

15D

SB1

CLK

15D

DGND

PSW

SP+

LCDV

5M

+B

5M

GND

SP-

GND

EXAFC

PTT

oE

33A

28M

CH_B

KIN

GND

EXSW

TGL0

TXo

oPT5

DI

SB2

TXI

oPT4

TCNT

C3

oPT3

MDWN

5A

RXEI

oPT2

AGND

INH

SToNRXEo

oPT1

AGND

DGND

UNIVERSAL CONNECTOR

MSW/CTS

MICE

SP-

PTT

DSR

5M

SP+

RXD

EMC

REM

TXD

ERTS1

SSW

GND

EXT ANT

GND

OPTION PCB

X57-725 D/5

S-

+

BATT

1

D1

14

D3

D0

1

D4

A0

D7

GND

WR

D2

*CN800 D5

NC

GND

D6

LCS

14

GND

A0

D5

D6

D3

D4

D7

LCS

GND

WR

D2

RD

D1

D0

CN803

CN601

CH_C

VoL

TGL1

L_KEY

MICE

S36M

GND

ORG

GND

NC

TXLED

TGL0

CH_A

BLED

TGL2

PF2

CH_B

33M

PF3

36M

CH_D

L_PTTG

L_MIC

L_KEY1

1CN804

1

6

20

PF1

L_PTT

61CN713

INT SP

INT MIC

(MAIN)

+-

CH_D

GND

TGL2

CH_C

CH_A

36M

GND

ORG

BLED

KIN

TGL0

S36M

TXLED

33M

17

CH_B

VoL

TGL1

1

CN903

NC MIC

VoL

CH_D

CH_B

TGL1

36M C

GND

CH_C

S36M

33M

CH_A

TGL2

12

CN902

1

*CN802

1

30

*LCD

ANT PCB

ANT

X57-725 E/5

CN204

CN205

*CN613

X57-725 A/5

X57-725 B/5

TX-RX PCB

CONTROL PCB

TOP PCB

X57-725 C/5

POWER SW/

CHANNEL

CONCENTRIC

AF VOL

SELECTOR

SW

SIDE2

SIDE3

PTT

SIDE1

X57-7250-XX

LCD

CN613

CN800

CN802

K4

K6

K5

K3

K2K

NO

NO

NO

NO

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

NO

-10

-11

-12

-14

-15

-13

NO

NO

NO

CN941

20

1

INT SP-

INT SP-

INT SP+

INT SP+

INT MIC-

INT MIC+

LCS

VDD

Vout

NC

NC

NC

NC

NC

NC

VR

V0

V1

V2

V3

V4

D7

WR

GND

D5

GND

LRST

D4

NC

D0

D3

D1

D6

E/RD

A0

D2

Page 92: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

87

BLOCK DIAGRAM

TC75W51FK(F)

SW

SW

2SJ243-A, SSM3K15TE(F)

SW

SSM3K15TE(F)

SW

TC7W66FK-F

AF amp

AF amp

EXT SP

INTSP

Amp

5M

INTMIC1

INTMIC2

(NoiseCancel)

5M5VSPamp

5VSPamp

INAFC

EXAFC

AVR

2SB798(DL,DK),UMG3N

SW

SSM3K15TE(F)

5AC

+B

3.6V DC/DCConverter

5.6VDET

CE

+B 3.3VRegulator

3.3VRegulator

1.5V DC/DCConverter

2.5VRegulator

33M 33A 25D 15D

PWR

5VRegulator

5MLM4906LD

LM4906LD

16keymatrix

shiftregister

BU4094BCFVx3

KEYscan

CLK,DAT,OE,KES 33M

INT/EXT gain control

5VSPamp

LED BACK LIGHT

AVR

2SB798(DL,DK),2SC4617(S)

LCD BACK LIGHT

PTT

SW

SW

+B5AC

ORANGEKEY

CONCENTRICSW

CH_ACH_BCH_CCH_DTGL1TGL2

SELECTORKNOB

KIN

KIN

KIN

TGL0

CH_ACH_BCH_CCH_DTGL0TGL1TGL2

SSM6L05FU

SSM6L05FU

+B

+B

POWERSW/

Volume

33M

VoL

MIC

TC75W51FK(F)

15V

LMC7101BIM5

LCDV

7.8~8.9V

LCD

TXLED

BUSYLED

1SS301F

XC6204B332M XC6204B332M XC6204B252M XC9225A15CM

TK11250CUCB

XC61CC5602NR

INT MIC1

INT MIC2

28M

XC6204B302M

1SS388F

15V DC/DCConverter

SwitchingTransistor/

Diode15V

XC9101D09AKR

SSM5H01TU

SB1

X57-7250-XX B/5(Control Unit)

AF

X57-7250-XX C/5

X57-7250-XX A/5(TX-RX Unit)

X57-7250-XX A/5(TX-RX Unit)

SIDE KEY

IC800

Q803

Q804

Q801 Q800

D703

IC707 IC708 IC711 IC709IC704

IC801,IC802,IC803

Q710 TPC6108-FD704 HRB0502A

IC710 XC6365D103M

IC706

IC705 IC701 IC703

IC702Q708

Q706 Q705

Q704 Q703

Q702 Q701

Q700

IC713

Q711

IC705

IC712

D701

2SJ243-A, SSM3K15TE(F)

PTT

3.0VRegulator

SW

Q713UM6K1N

Q712UM6K1N

CE CE CECE

SWCE

+B

Page 93: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

88

BLOCK DIAGRAM

T/RSW

D200,D308HVC131x2

Q2002SC5108(Y)F

Q2102SK3077F

PLL IC

TX : 450.00 – 520.00 MHz(K,K2,K3)380.00 – 470.00 MHz(K4,K5,K6)

RX : 400.05 – 470.05 MHz(K,K2,K3)330.05 – 420.05 MHz(K4,K5,K6) TX VCO

Q110 (K4,K5,K6)Q1112SC5108(Y)F

+B

6.0~9.0V

VCXO

5CS33A

VcontS33A

5C 5T

SWVCO Vdd

MOD

FlashROM

EEPROM

Reset

IC5CPU

30625MGP346HU

5M

33A

Vcont(VCXO)

5M

SUM

MOD(VCO)

Balance

Max. Deviation

DAC3CH

DAC4CH

fcDAC5CH

CVCO

CVCO

VCO Vdd

VCO Vdd

RTC

AVR

5CC

AVR

PWR

5TC

5CT/R

RX VCO

CLKDAT

STRB

LD

5T

5M

IC462RX AudioVolume

DAC6CH

Option Board Connector (VGS,ANI board,Scrambler board)

5RC

SW

SW

5R

5T

33A

33M

15D

25D

5MCS

5M

SW

5MC

X57-7250-XX B/5(Control Unit)

F600FUSE

BATT

28M

AO toVGS

RXEo toScrambler

IC603TC74VHCT244AFT

3.3→5V LevelConverter

CLK,DAT,STRB,OE

UniversalConnector

16.8MHz

33M 33M

33M

33M

5M

IC462DAC

CH2

CH3

CH4 CH5

CH6

CH7

CH8

2nd LocalAdjust

CH1BPF

Tuning2

MaxDeviation

BalanceAdjust

APCTuning

BPFTuning

RX AF

FrequencyAdjust

DAT,CLK,LD 5M AVDref(2V)

ASSIST(PLL Assist

Circuit)

CV toCPU

28M

5T5R

STONE fromANI AI from

VGS

RXEIfromScrambler

IC101ADF4111BCP7

32.768kHz

M62364FP-F

X57-7250-XX A/5(TX-RX unit)

IC3AT2425610TI27

IC2RV5C386A

IC4S-80930CNNB-G

IC6

S33A

Q1092SC5108(Y)F

RX AF

IC463(1/2)TC75W51FK(F)

Shift Register

IC606BU4094BCFV

LCD BUS

5M

DAC(LD)

CLK1,DAT1,STRB1,OE1

Q604,Q603TPC6108-F,SSM3K15TE(F)

15V

VCO Vdd

SW

Q602SSM6L05FU

SB

Q600SSM6L05FU

Q601SSM6L05FU

IC600XC6204B502PR

IC601XC6204B502MR

Q105,Q108SSM6L05FU,2SJ347F

CPUCLK

LOOP Filter

Q1032SK879(Y)F

SW

5CC

S33A

Q101SSM6L05FU

PWR

BATT

33M

BATTDET

BATTDET

LCD BUS

BUS SW

IC607TC7MB3245FK,

IC608/IC609TC7WB125FK x 2

5M

LCS

X57-7250-XX D/5(Option Board)

X1

IC7TC7S08FU-F

X100

IC462

IC462

Q1122SC5108(Y)F

SW

SCSW

IC458(1/2)TC7W66FK-F

SW

BEEPS

IC458(2/2)TC7W66FK-F

AVR

IC610TK11250CUCB

36MD

Page 94: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

89

BLOCK DIAGRAM

Q202RD01MUS1-T113

Q204RD07MVS2

ANTSW

D202/D203/D204/D205HVC131 x4

ATT

BPF

3SK318BPF

VCTUNE

D301/D3021SV286F x 2

ATT

APC

TX : 450.00 – 520.00 MHz(K,K2,K3)380.00 – 470.00 MHz(K4,K5,K6)

IC304FM IC TA31137FNG

MCF

Q3022SK1215-E(E)

x3

5R5R

5R

IC308Buffer AMP

IF1 : 49.95 MHz

IC457FPGA

EX128TQ64I630C

33D

IC454CODEC

AK4550VTP

VC-TCXO

CD300DISCRIMINATOR

rectifier

SW MUTE

MM33A

33D

15D

TX AF

VC TUNED304/D305/D306/D307

1SV286F x4

TUNE

CeramicFilter

VCXO

33A Vcont

+B

Drive AMP Final AMP

+B APCSW

Q301LNA

LPF

LPF

1st IF AMP

CF303Wide

CF302Narrow

CF301P25

RSSI

AF OUT

2nd IF 450kHz

16.8MHz Lo2 : 50.4 MHzUpperHetero

8bitShift

Register

25D

from MIC AMPin Control unit

18.432MHz

AMP

IC451(2/2)Active BPF

IC8DSP

5V→3.3VLevel

Converter

9CH

TXI from Scrambler

5V→3.3VLevel Convert

Shift RegisterOutput

D Flip-flop

9.216MHz

CPUCLK

PWDA,PWADSCLK,MCLK,

LRCKSDTI,SDTO

To Option ConnectorVIA 3.3V→5.0V Level

Converter

From Option Connector,Universal ConnectorTo CPU

BSFT x2(Beat Shift)

33A

5R

TX/RX : 450.00 – 520.00 MHz(K,K2,K3)380.00 – 470.00 MHz(K4,K5,K6)

Lo1: 400.05 – 470.05 MHz(K,K2,K3)330.05 – 420.05 MHz(K4,K5,K6)

IC455(1/3)TC7WU04FK-F

33M

33A

33M

SPM5001

Universal Connector

WN WN

VN VN33A

5R

AMP

FM(analog)

33A

33A

IC202/IC203MASWSS0181

x2

SW

LPF

LPF

Main ANT

EXT ANT

5M

TC7WU04FK-F

IC302Active DBM

IC456(1/2)TC75W51FK(F)

Q3032SC5108(Y)F

TC75W51FK(F)

IC459(2/2)TC75W51FK(F)

Q4602SC4617(S)

P25(C4FM,CQPSK)

Q452SSM3K15TE(F)

IC452(1/2)TC75W51FK(F)

P25DET

EXT SP

EXT MIC

CLK,STRB,OE,CS

DSPCLK

CF300Ceramic Filter

Q2092SJ243-A

IC303TC7W53FK

(F)IC306

TC7W53FK(F)

IC305TC7W53FK

(F)IC307

TC7W53FK(F)

IF2 OUT

IC453TC7WH74FK-F

CLK

IC455(2/3)TC7WU04FK-F

33M

33M

33M

IC455(3/3)TC7WU04FK-F

X57-7250-XX E/5

IC201TA75W01FUF

X300

33A

AM

PIC456(1/2)

TC75W51FK(F)

AGCAMP

Q4542SJ347F

SCSW

AMP

33A

IC459(1/2)TC75W51FK(F)

IC452(2/2)TC75W51FK(F)

BufferAMP

33A

AI fromVGS

AO to VGS,TXO to Scrambler

CN601(for production)

TO DSP

EXT ANT

SSWMSW/CTS

PTTREMRTS1

5MTXDRXDDSR

SQL

AMP

RX : 450.00 – 520.00 MHz(K,K2,K3)380.00 – 470.00 MHz(K4,K5,K6)

Page 95: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

90

Mode : Wide

Q301 IC302 MCF Q302 IC304IC202&203C270&271 C306 C361 C370 C374 C387

12dB SINAD (dBm) -122.9 -123.6 -124.3 -115.8 -113.0 -118.1 -112.0

FM-IC

Receiver SectionRF (Center Frequency) IF1 (49.95MHz)

CF301

Mode : Wide IC304 CF300 IC304 IC303 IC305 IC304C395 C396 C393 C394

IC306 IC307

CF302184 163 104 74.6(mVrms)CF303

FM-IC FM-IC FM-IC

IF2 (450kHz)

Internal SP

IC702

IC459IC304 IC454 IC456 IC462 IC705IC458

IC701

External SPIC703

Wide(mVrms) 143 210 88.5 340 333 83.5 83.1 530 527 2000 -Narrow(mVrms) 157 229 97.5 371 364 83.7 83.1 533 530 2000 -

Wide(mVrms) - 696 693 2700 2000Narrow(mVrms) -

--

--

--

--

--

-- 685 682 2700 2000

Internal

External

FM-IC CODEC DAC

IC461

AF (1kHz)

D200T/R SW

Q202Drive Amp

Q204Final Amp

D202,D203ANT_SW

LPF

Q200Pre Pre Drive Amp

Q210Pre Drive Amp

Attenuator

IC202,IC203SPDT

CN204

CN205

Q109

AttenuatorVCOQ112

-2dBm -10dBm 0dBm K,K2,K3: 10dBmK4,K5,K6: 9dBm

20dBm19dBm

15dBm16dBm

37.5dBm

35.5dBm36.0dBm

RF (Center Frequency)RF (Center Frequency x2)

Transmitter Section

IC705 IC452 IC452InternalMIC Q455 Q454

Internal (mVrms) 15.0 15.1 14.3 13.0ExternalMIC

External (mVrms) 15.0 13.8 96.9 83.6 49.4

CODEC

AF (1kHz)

IC454 IC456 IC459 IC462

Wide (mVrms) 174.6Narrow (mVrms) 86.7 IC463

Wide (mVrms) 183.8 362.5Narrow (mVrms) 91.4 182.5

588

VCO

TCXO

269.5 1030 DAC

LEVEL DIAGRAM

To make measurements in the AF section, connect the AC level meter. (ANT input: -47dBm, 1kHz FM, 3kHz DEV (Wide), 1.5kHz DEV (Narrow))In the RF section, use 1000pF coupling capacitor.(The display shows the SSG input value required to obtain 12dB SINAD without local level.)

Wide: AG is set to the MIC input becomes 3kHz DEV at 1kHz MOD.Narrow: AG is set to the MIC input becomes 1.5kHz DEV at 1kHz MOD.To make measurements in the AF section, connect the AC level meter.In the RF section, use 1000pF coupling capacitor.

Page 96: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310

91

MEMO

Page 97: UHF P25 TRANSCEIVER TK-5310manuals.repeater-builder.com/Kenwood/tk/TK-5310_B51-8779-00.pdfthen release the [Side3] key first. Clone mode ∗2 Press and hold the [Side2] and [PTT] keys

TK-5310SPECIFICATIONS

GENERALModels ............................................................................. K, K4 : Basic Model K2, K5 : 4-Key w/LCD Model K3, K6 : Full Key w/LCD ModelFrequency Range ............................................................. K, K2, K3 : 450~520 MHz K4, K5, K6 : 380~470 MHzNumber of Channels ........................................................ 512Zones ............................................................................... 50Max. Channels per Zone ................................................. 250Channel Spacing .............................................................. Analog : 12.5/25 kHz Digital : 12.5 kHzOperating Voltage ............................................................ 7.5V DC ± 20%Battery Life (5-5-90 (10-10-80) duty cycle) ...................... KNB-31A, 7.5VDC, 1700 mAh : 8 hours (5 hours)

KNB-32N, 7.5VDC, 2500 mAh : 12 hours (8 hours) KNB-33L, 7.5VDC, 1700mAh : 8 hours (5 hours) KBP-6, AA Alkaline x 6 Batteries : 8 hours (5 hours)

Operating Temperature Range ........................................ –22°F to +140°F (–30°C to +60°C)Frequency Stability (–22°F to +140°F) ............................ ±2.0 ppmAntenna Impedance ........................................................ 50ΩDimensions (W x H x D) .................................................. 2-5/16 x 6-3/32 x 1-13/16 in. (58 x 155 x 45.7 mm) with KNB-31A or KNB-32N battery

(Projections not included) 2-5/16 x 6-3/32 x 1-9/16 in. (58 x 155 x 39.2 mm) with KNB-33L battery 2-23/64 x 6-3/32 x 1-27/32 in. (60 x 155 x 46.7 mm) with KBP-6 battery

WeightRadio only ................................................................... TK-5310 K, K4 : 11.11 oz. (315g)

TK-5310 K2, K5 : 11.64 oz. (330g) TK-5310 K3, K6 : 11.64 oz. (330g)

TK-5310 K2 with battery, ............................................ 22.22 oz. (630g) with KNB-31A batteryantenna (KRA-23) and belt clip (KBH-11) 23.28 oz. (660g) with KNB-32N battery

17.64 oz. (500g) with KNB-33L battery

RECEIVERSensitivity ........................................................................ Digital (5% BER) : 0.25µV Digital(1% BER) : 0.40µV

Analog 12dB SINAD : 0.25µVSelectivity ........................................................................ Digital : -60dB Analog @25kHz : -75dB Analog @12.5kHz : -67dBIntermodulation Distortion ............................................... Digital : -75dB Analog @25kHz : -75dB Analog @12.5kHz : -68dBSpurious and Image ......................................................... Digital : -75dB Analog :- 75dBAudio Distortion ............................................................... Digital : Less than 1.5% Analog : Less than 2%Audio Output ................................................................... 500mW/ 8Ω

TRANSMITTERRF Power Output ............................................................. 4W / 1WSpurious and Harmonics .................................................. 70dBFM Hum and Noise ......................................................... Analog @25kHz : 48dB Analog @12.5kHz : 42dBAudio Distortion ............................................................... Less than 2%Modulation ....................................................................... 16K0F3E, 11K0F3E, 8K10F1E, 8K10F1D

Analog measurements made per TIA/EIA-603Digital measurements made per TIA/EIA-102CAAAKENWOOD reserves the right to change specifications without prior notice or obligation.

2967-3, Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan

P.O. BOX 22745, 2201 East Dominguez Street, Long Beach,

6070 Kestrel Road, Mississauga, Ontario, Canada L5T 1S8

Rembrücker Str. 15, 63150 Heusenstamm, Germany

Leuvensesteenweg 248 J, 1800 Vilvoorde, Belgium

KENWOOD House, Dwight Road, Watford, Herts.,

Amsterdamseweg 37, 1422 AC Uithoorn, The Netherlands

Via G. Sirtori, 7/9 20129 Milano, Italy

Bolivia, 239-08020 Barcelona, Spain

(A.C.N. 001 499 074)16 Giffnock Avenue, Centrecourt Estate, North Ryde, N.S.W. 2113 Australia

Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road,

1 Ang Mo Kio Street 63, Singapore 569110

CA 90801-5745, U.S.A.

Kwai Fong, N.T., Hong Kong

WD18 9EB United Kingdom

L’Etoile Paris Nord 2, 50 Allée des Impressionnistes, Bp 58416 Villepinte, 95944 Roissy Ch De Gaulle Cedex