INSTRUCTION MANUAL

UHF dPMR MOBILE TRANSCEIVER

iF6062D

VHF dPMR MOBILE TRANSCEIVER

iF5062D

�

IMPORTANTREAD ALL INSTRUCTIONS carefully and com-pletely before us�ng the transce�ver.

SAVE THIS INSTRUCTION MANUAL — Th�s �nstruct�on manual conta�ns �mportant operat�ng �nstruct�ons for the IC-F5062D VHF dPMR MOBILE TRANSCEIVER, IC-F6062D UHF dPMR MOBILE TRANSCEIVER.

• Th�s �nstruct�on manual �ncludes some funct�ons wh�ch are usable only when they are pre-programmed by your dealer. Ask your dealer for deta�ls.

• See the operat�ng gu�de for deta�ls of BIIS (B�nary Inter-change of Informat�on and S�gnal�ng) and dPMR (d�g-�tal Pr�vate Mob�le Rad�o) system operat�ons. Ask your dealer for deta�ls.

EXPLICIT DEFENITIONS

WORD DEFINITION

RWARNING!Personal �njury, f�re hazard or electr�c shock may occur.

CAUTION Equ�pment damage may occur.

NOTEIf d�sregarded, �nconven�ence only. No r�sk of personal �njury, fire or electr�c shock.

Icom, Icom Inc. and the Icom logo are reg�stered trademarks of Icom Incor-porated (Japan) �n Japan, the Un�ted States, the Un�ted K�ngdom, Germany, France, Spa�n, Russ�a and/or other countr�es.All other products or brands are reg�stered trademarks or trademarks of the�r respect�ve holders.

RWARNING! NEVER connect the transce�ver to an AC outlet. Th�s may pose a fire hazard or result �n an electr�c shock.

RWARNING! NEVER connect the transce�ver to a power source of more than 16 V DC or use reverse polar�ty. Th�s could cause a fire or damage the transce�ver.

RWARNING! NEVER cut the DC power cable be-tween the DC plug and fuse holder. If an �ncorrect connec-t�on �s made after cutt�ng, the transce�ver m�ght be damaged.

CAUTION: NEVER place the transce�ver where nor-mal operat�on of the veh�cle may be h�ndered or where �t could cause bod�ly �njury.

CAUTION: NEVER allow ch�ldren to touch the trans-ce�ver.

CAUTION: NEVER expose the transce�ver to ra�n, snow or any l�qu�ds.

USE the spec�f�ed m�crophone only. Other m�crophones have d�fferent p�n ass�gnments and may damage the trans-ce�ver.

DO NOT use or place the transce�ver �n areas w�th tem-peratures below –25°C or above +55°C, or �n areas subject to d�rect sunl�ght, such as the dashboard.

DO NOT operate the transce�ver w�thout runn�ng the ve-h�cle’s eng�ne. The veh�cle’s battery w�ll qu�ckly run out when the transce�ver transm�ts wh�le the veh�cle’s eng�ne �s OFF.

DO NOT place the transce�ver �n excess�vely dusty env�-ronments.

DO NOT place the transce�ver aga�nst walls. Otherw�se heat d�ss�pat�on w�ll be obstructed.

DO NOT use harsh solvents such as benz�ne or alcohol when clean�ng, as they damage the transce�ver surfaces.

BE CAREFUL! The transce�ver w�ll become hot when operat�ng cont�nuously for long per�ods.

PRECAUTIONS

��

12345678910111213141516

���

VOICE CODING TECHNOLOGYThe AMBE+2™ vo�ce cod�ng Technology embod�ed �n th�s product �s protected by �ntellectual property r�ghts �nclud�ng patent r�ghts, copyr�ghts and trade secrets of D�g�tal Vo�ce Systems, Inc. Th�s vo�ce cod�ng Technology �s l�censed solely for use w�th�n th�s Commun�cat�ons Equ�pment. The user of th�s Technology �s expl�c�tly proh�b�ted from attempt�ng to extract, remove, decomp�le, reverse eng�neer, or d�sassemble the Object Code, or �n any other way convert the Object Code �nto a human-readable form. U.S. Patent Nos.#5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.

�v

12345678910111213141516

TABLE OF CONTENTSIMPORTANT .......................................................................... �EXPLICIT DEFENITIONS ..................................................... �PRECAUTIONS .................................................................... ��VOICE CODING TECHNOLOGY ........................................ ���TABLE OF CONTENTS ....................................................... �v

1 PANEL DESCRIPTION ................................................1–7 ■ Front panel ...................................................................1 ■ Funct�on d�splay ...........................................................2 ■ Programmable funct�on keys ........................................3

2 BASIC OPERATION ..................................................8–15 ■ Turn�ng the power ON ..................................................8 ■ Channel select�on .........................................................8 ■Call procedure ..............................................................9 ■Rece�v�ng and transm�tt�ng ...........................................9 ■User Set mode ...........................................................12 ■ Emergency transm�ss�on ............................................13 ■ Scrambler funct�on .....................................................14 ■ Stun funct�on ..............................................................14 ■ Pr�or�ty A channel select�on ........................................14 ■ Forced Narrow funct�on ..............................................15 ■ Automat�c Key Lock funct�on ......................................15 ■ Power Off Emergency funct�on ...................................15

3 CONNECTION AND MAINTENANCE ....................16–20 ■ Rear panel connect�on ...............................................16 ■ Suppl�ed accessor�es .................................................18 ■ Mount�ng the transce�ver ............................................18 ■ Antenna ......................................................................19 ■ Fuse replacement ......................................................19 ■ Clean�ng .....................................................................19 ■ Opt�ons .......................................................................20

4 DOC .........................................................................21–23

Icom Inc.

q e

y

SpeakerFunction display (p. 2)w r

t

■ Front panel

q AF VOLUME CONTROL KNOB [VOL] Rotate the knob to adjust the aud�o output level. • M�n�mum aud�o level �s preprogrammed.

wLED INDICATOR ➥ L�ghts red wh�le transm�tt�ng a s�gnal. ➥ L�ghts green wh�le rece�v�ng a s�gnal.

e UP/DOWN KEYS [CH Up]/[CH Down] Push to select an operat�ng channel, etc. *Requ�red funct�ons can be ass�gned by your dealer. (p. 3)

rPOWER SWITCH [ ] Hold down for 1 second to turn the power ON or OFF. • Automat�c scan start, Password prompt and User Set mode ac-

cess are ava�lable at power ON.

tDEALER-PROGRAMMABLE KEYS Requ�red funct�ons can be programmed �ndependently by

your dealer. (p. 3)

yMICROPHONE CONNECTOR Connect the suppl�ed or opt�onal m�crophone. NEVER connect non-spec�fied m�crophones. The p�n

ass�gnments may be d�fferent and may damage the transce�ver.

D MICROPHONEThe suppl�ed m�crophone has a PTT sw�tch and a hanger.• The follow�ng funct�ons are ava�lable when you put the m�crophone

ON hook, or take �t OFF hook (depend�ng on the pre-programmed sett�ngs):

- Automat�c scan starts when you put �t ON hook. - Scan �s paused or cancelled when you take �t OFF hook. - Automat�cally selects the Pr�or�ty A channel when you take �t OFF

hook. - Sets to the ‘Inaud�ble’ (mute) mode when you put �t ON hook. - Sets to the ‘Aud�ble’ (unmute) mode when you take �t OFF hook.

1

1 PANEL DESCRIPTION

■ Function display

Icom Inc.

!1

q w e r t y iu o

!0

qSIGNAL STRENGTH ICON Shows relat�ve rece�ve s�gnal strength level.

wLOW POWER ICON Appears when low output power �s selected.

e AUDIBLE ICON ➥ Appears when the channel �s �n the ‘Aud�ble’ (unmute)

mode. ➥ Appears when a match�ng s�gnal �s rece�ved.

r COMPANDER ICON Appears when the Compander funct�on �s act�vated.

t SCRAMBLER ICON Appears when the Vo�ce Scrambler funct�on �s act�vated.

y BELL ICON Appears/bl�nks when a match�ng s�gnal �s rece�ved, de-

pend�ng on the pre-programmed sett�ngs.

u CALL CODE MEMORY ICON Appears when the call code memory �s selected.

i SCROLL ICON Appears when an SDM (Short Data Message), �nclud�ng

more than 12 characters, �s selected �n the rece�ved mes-sage select�on mode*1, 2.

o SDM ICON Appears when an SDM �s rece�ved, or an SDM �s selected

to transm�t*1, 2.

!0 ALPHANUMERIC DISPLAY ➥ D�splays an operat�ng channel number, channel name,

User Set mode contents, DTMF code, etc. ➥ Depend�ng on the pre-programmed sett�ngs, characters

are d�splayed �n 1 l�ne or 2 l�nes on the LCD. • In th�s �nstruct�on manual, the LCD �llustrat�on �s descr�bed as

hav�ng characters d�splayed �n 2 l�nes.

!1 ACTIVATED KEY ICON Appears above the key ass�gned as [Scan], [Scan Add/

Del(Tag)], [Lock], [Talk Around], [Surve�llance] and [BIIS Button]*1, wh�le that key �s act�vated.

*1 BIIS operat�on only*2 dPMR operat�on only

See the operat�ng gu�de for deta�ls of BIIS and dPMR sys-tem operat�ons. Ask your dealer for deta�ls.

2

1PANEL DESCRIPTION

12345678910111213141516

Weak Receive Signal level Strong

3

1 PANEL DESCRIPTION

■ Programmable function keysThe follow�ng funct�ons can be ass�gned to [UP], [DOWN], [P0], [P1], [P2], [P3] and [P4] programmable funct�on keys.Consult your Icom dealer or system operator for deta�ls con-cern�ng your transce�ver’s programm�ng.If the programmable funct�on names are bracketed �n the fol-low�ng explanat�ons, the spec�fic key �s used to act�vate the funct�on, depend�ng on the pre-programmed sett�ngs.

INFORMATION:Depend�ng on the pre-programmed sett�ngs, the pro-grammed funct�on for [P0], [P1], [P2] or [P3] �s ass�gned to [A], [B], [C] or [D] of the opt�onal HM-152T, respec-t�vely. Ask your dealer for deta�ls.

CHANNEL UP, CHANNEL DOWN ➥ Push to select an operat�ng channel.➥ As descr�bed �n the follow�ng top�cs, after push�ng a pro-

grammed key, push [CH Up] or [CH Down] to select an opt�on, sett�ng, etc.

ZONEPush th�s key, then push [CH Up] or [CH Down] to select the des�red zone.

What is “zone”?—Certa�n channels are grouped together and ass�gned to a zone, accord�ng to the�r �ntended use. For example, ‘Staff A’ and ‘Staff B’ are ass�gned to a “Bus�-ness” zone, and ‘John’ and ‘C�ndy’ are ass�gned to a “Pr�-vate” zone.

ZONE UP, ZONE DOWNPush to select an operat�ng zone.

SCAN➥ Push to start or cancel a scann�ng operat�on. • When a scan �s started by the Power ON Scan or Automat�c

Scan funct�on, push th�s key to cancel the scan. The cancelled scan resumes after the pre-programmed t�me per�od.

➥ Hold down th�s key for 1 second to d�splay the scan group, then push [CH Up] or [CH Down] to select the des�red one.

SCAN ADD/DEL (TAG)➥ Push to add the selected channel to, or delete �t from, the

scan group. 1. Push to d�splay the scan group, and then push [CH Up] or

[CH Down] to select the des�red one. 2. Push to add the channel to, or delete �t from, the selected scan

group. 3. Hold down for 1 second to ex�t the scan group select�on mode.➥ Wh�le a scan �s paused on a non-pr�or�ty channel, push th�s

key to delete the selected channel from the scan group.

Depend�ng on the pre-programmed sett�ngs, the cleared channel �s added to the scan group aga�n after the scan �s cancelled. (Nu�sance Delete funct�on)

4

1PANEL DESCRIPTION

1

PRIORITY A, PRIORITY BPush to select the Pr�or�ty A or Pr�or�ty B channel.

PRIORITY A (REWRITE), PRIORITY B (REWRITE)➥ Push to select the Pr�or�ty A or Pr�or�ty B channel.➥ Hold down for 1 second to ass�gn the operat�ng channel to

the Pr�or�ty A or Pr�or�ty B channel.

MEMORY CHANNELS 1, 2, 3, 4Push to select memory channel 1, 2, 3 or 4.

MONITOR, MONITOR (AUDIBLE) ➥ Push to turn the CTCSS (DTCS) or 2/5-tone squelch mute

ON or OFF. • Only dur�ng LMR (Land Mob�le Rad�o) operat�on, push to

open any squelch, or deact�vate any mute funct�ons. • Only dur�ng PMR (Pr�vate Mob�le Rad�o) operat�on, push

to act�vate one or two of the follow�ng funct�ons on each channel (Depend�ng on the pre-grogrammed sett�ngs):

- Hold down to unmute the channel (‘Aud�ble’ mode). - Push to mute the channel (‘Inaud�ble’ mode). - After the commun�cat�on �s fin�shed, push to send a ‘reset code’

(5-tone) or a ‘Clear Down’ s�gnal (BIIS). NOTE: The ‘Aud�ble’ (unmute) mode may automat�cally

return to the ‘Inaud�ble’ (mute) mode, after the pre-pro-grammed t�me per�od.

➥ Depend�ng on the pre-programmed sett�ngs, hold�ng down th�s key for 1 second cancels a scan.

PUBLIC ADDRESSPush to act�vate the PA (Publ�c Address) funct�on. When th�s funct�on �s turned ON, the aud�o level can be separately con-trolled from the transce�ver by push�ng [CH Up] or [CH Down].• Th�s funct�on can be used when external equ�pment, such as an

aud�o ampl�fier, speaker, etc. �s connected.• Push th�s key, then hold down [PTT] and speak �nto the m�cro-

phone.

RX SPEAKERPush to turn the RX Speaker funct�on ON or OFF.When th�s funct�on �s turned ON, the rece�ved aud�o can be heard through an external speaker.• Th�s funct�on �s useful when you are away from the transce�ver.• The aud�o output level �s l�nked to the transce�ver’s volume control.

LIGHTPush to turn the backl�ght ON for about 5 seconds, when the Backl�ght funct�on �s set to “OFF” �n the User Set mode.

LOCK➥ Hold down th�s key unt�l “LOCK ON” �s d�splayed to elec-

tron�cally lock all programmable keys except the follow�ng: [Mon�], [L�ght], [Lock], [Call] (�ncl. Call A and Call B), [Emergency],

[Surve�llance], [Lone Worker] and [OPT 1/2/3].➥ When the Key Lock funct�on �s ON, hold down th�s key

unt�l “LOCK OFF” �s d�splayed to turn �t OFF.

5

1 PANEL DESCRIPTION

LONE WORKERPush to turn the Lone Worker funct�on ON or OFF.• If the Lone Worker funct�on �s turned ON, and no operat�on occurs

dur�ng the pre-programmed t�me per�od, the Emergency funct�on �s automat�cally turned ON.

HIGH/LOWPush to select the transm�t output power level temporar�ly or permanently, depend�ng on the pre-programmed sett�ngs.• Ask your dealer for the output power level for each select�on.

TONE/COLOUR CODE CH SELECT➥ Wh�le �n the analog mode, push to enter the cont�nuous

tone select�on mode. Then push [CH Up] or [CH Down] to select the des�red tone frequency/code sett�ng. After se-lect�ng, push th�s key aga�n to store the sett�ng.

➥ Wh�le �n the d�g�tal mode, push to enter the colour code select�on mode. Then push [CH Up] or [CH Down] to se-lect the des�red colour code. After select�ng, push th�s key aga�n to store the sett�ng.

➥ Wh�le �n the m�xed (d�g�tal and analog) mode, push to enter the cont�nuous tone select�on mode. Then push [CH Up] or [CH Down] to select the des�red tone frequency/code set-t�ng. After select�ng, push th�s key to store the sett�ng. After that, the colour code select�on screen appears. Push [CH Up] or [CH Down] to select the des�red colour code. After select�ng, push th�s key aga�n to store the sett�ng.

C.TONE CH ENTPush to enter the cont�nuous tone channel select�on mode. Then push [CH Up] or [CH Down] to select the des�red tone frequency/code sett�ng. The selected channel rema�ns set unt�l another channel �s des�gnated.

TALK AROUNDPush to turn the Talk Around funct�on ON or OFF.• The Talk Around funct�on equal�zes the transm�t frequency to the

rece�ve frequency for transce�ver-to-transce�ver commun�cat�on.

WIDE/NARROWPush to sw�tch the IF bandw�dth between w�de and narrow.• The w�de passband w�dth �s pre-programmed to e�ther 25.0 or

20.0 kHz by your dealer (PMR operat�on only).

DTMF AUTODIALPush to enter the DTMF channel select�on mode, then push [CH Up] or [CH Down] to select a des�red DTMF channel.After select�ng, push aga�n to transm�t the selected DTMF code.

RE-DIALPush to transm�t the last-transm�tted DTMF code.• TX memor�es are cleared after turn�ng the power OFF.

6

1PANEL DESCRIPTION

1CALL, CALL A, CALL BPush to transm�t a 2/5-tone code or BIIS/dPMR call.• Call transm�ss�on �s necessary before call�ng another stat�on,

depend�ng on your s�gnall�ng system.• [Call A] and/or [Call B] may be ava�lable when your system employs

select�ve ‘Ind�v�dual/Group’ calls. Ask your dealer wh�ch call �s ass�gned to each key.

EMERGENCYHold down for the pre-programmed t�me per�od to enter the emergency mode. After the pre-programmed t�me per�od, an Emergency call �s transm�tted once, or repeatedly*. (p. 13)• To ex�t the emergency mode, hold down th�s key for the pre-pro-

grammed t�me per�od aga�n, before transm�tt�ng.* Depend�ng on the pre-programmed sett�ngs.

SURVEILLANCEPush to turn the Surve�llance funct�on ON or OFF.When th�s funct�on �s turned ON, the beep does not sound and the LCD backl�ght and the LED �nd�cator do not l�ght, even when a s�gnal �s rece�ved or a key �s pushed.

TX CODE ENTERPush to enter the TX code ed�t mode (5Tone) (p. 11) or the ID code ed�t mode (BIIS, dPMR), and then set the des�red TX code or ID code.

TX CODE CHANNEL SELECT➥ Push to enter the TX code channel select�on mode (p. 10)

or the ID select�on mode (BIIS, dPMR), and then push [CH Up] or [CH Down] to select the des�red channel or ID.

➥ Hold down th�s key for 1 second to enter the TX code ed�t mode (5Tone) (p. 11) or the ID code ed�t mode (BIIS, dPMR), and then set the des�red TX code or ID code.

TX CODE CHANNEL UP, TX CODE CHANNEL DOWNPush to select a TX code channel (p. 10) or ID (BIIS, dPMR).

SCRAMBLER Push to turn the Vo�ce Scrambler funct�on ON or OFF.

COMPANDERPush to turn the Compander funct�on ON or OFF. The Compander funct�on reduces no�se components from the transm�tted aud�o to prov�de clear commun�cat�on.

ID-MR SELECT➥ Recalls detected ID codes. • Push th�s key, then push [CH Up] or [CH Down] to select the ID

code. • Up to 5 IDs are memor�zed.➥ Hold down for 1 second to erase the selected ID.

See the operat�ng gu�de for deta�ls of BIIS and dPMR sys-tem operat�ons. Ask your dealer for deta�ls.

7

1 PANEL DESCRIPTION

HOOK SCANWhen the Hook Scan funct�on �s pre-programmed, push th�s key to d�sable the funct�on. Push th�s key aga�n to enable the funct�on.

USER SET MODE➥ Hold down for 1 second to enter the User Set mode. • In the User Set mode, push th�s key to select an �tem that �s ena-

bled by your dealer, and change the value or sett�ng by push�ng [CH Up] or [CH Down].

➥ Hold down for 1 second aga�n to ex�t the User Set mode.

The User Set mode �s also ava�lable us�ng the Power ON funct�on. Refer to page 12.

10Key ENTPush to enable the m�crophone’s 10-keypad operat�on.• Depend�ng on the pre-programmed sett�ngs, 10-keypad can be

used to select a des�red memory channel, ID l�st number (dPMR), TX status (BIIS, dPMR) or Short Data Message (dPMR), or enter a des�red TX code (5-tone) or ID (dPMR).

OPT 1 OUT, OPT 2 OUT, OPT 3 OUTPush to output the control s�gnal to the opt�on connector. Ask your dealer for deta�ls.

OPT 1 MOMENTARY, OPT 2 MOMENTARY,OPT 3 MOMENTARYOutputs the control s�gnal to the opt�on connector wh�le hold-�ng down th�s key. Ask your dealer for deta�ls.

POWER OFF EMERGENCYWh�le hold�ng down th�s key, turn the power OFF to act�vate the Power OFF Emergency funct�on.Th�s funct�on makes the transce�ver transm�t emergency calls, even though �t appears to be powered OFF. (p. 15)

8

2BASIC OPERATION

12345678910111213141516

■ Turning the power ONq Hold down [ ] for 1 second to turn the power ON.w If the transce�ver �s programmed for a start up password,

�nput the d�g�t codes as d�rected by your dealer. • The keys as below can be used for password �nput: The transce�ver detects numbers �n the same block as �dent�cal.

Therefore “01234” and “56789” are the same.

e When the “PASSWORD” �nd�cat�on does not clear after �nputt�ng 6 d�g�ts, the �nput code number may be �ncorrect. Turn the power OFF and start over, �n th�s case.

■ Channel selectionSeveral types of channel select�on are ava�lable. Methods may d�ffer, accord�ng to your system set up.

NON-ZONE TYPE:To select the des�red operat�ng channel:• Push [CH Up] or [CH Down].• Push one of [MR-CH 1] to [MR-CH 4].

ZONE TYPE:To select the des�red zone:• Push [Zone], then push [CH Up] or [CH Down].• Push [Zone Up] or [Zone Down].

D Voting operationThe transce�ver automat�cally starts scann�ng when a zone, spec�fied for the vot�ng operat�on, �s selected.The vot�ng scan detects the s�gnal strength of the repeaters, and automat�cally selects the strongest one.

AUTOMATIC SCAN TYPE:Channel sett�ng �s not necessary for th�s type. When turn�ng the power ON, the transce�ver automat�cally starts scann�ng. Scann�ng stops when rece�v�ng a call.

KEY

NUMBER0

5

4

9

3

8

2

7

1

6

■Call procedureWhen your system employs tone s�gnall�ng (exclud�ng CTCSS and DTCS), a call procedure may be necessary pr�or to vo�ce transm�ss�on. The tone s�gnall�ng employed may be a selec-t�ve call�ng system, wh�ch allows you to call spec�fic stat�on(s) only, and prevent unwanted stat�ons from contact�ng you.

q Select the des�red TX code channel accord�ng to your sys-tem operator’s �nstruct�ons.

• Th�s may not be necessary, depend�ng on programm�ng. • Refer to pages 10 and 11 for deta�ls.w Push [Call] (ass�gned to one of the dealer programmable

keys).e After transm�tt�ng, the rema�nder of your commun�cat�on

can be carr�ed out �n the normal fash�on.Selective calling Non-selective calling

■Receiving and transmittingReceiving:q Hold down [ ] for 1 second to turn the power ON.w Push [CH Up] or [CH Down] to select a channel.e When rece�v�ng a call, rotate [VOL] to adjust the aud�o

output level to a comfortable l�sten�ng level.

NOTE: Depend�ng on the pre-programmed sett�ngs, the transce�ver automat�cally transm�ts the m�crophone aud�o for the pre-programmed t�me per�od when a match�ng s�g-nal �s rece�ved.

• The HM-148G or HM-152 hand microphone �s requ�red.

Transmitting:Wa�t for the channel to become clear to avo�d �nterference.q Take the m�crophone OFF hook. • 2/5-tone mute may be released. (The ‘Aud�ble’ (unmute) mode

�s selected and LED �nd�cator l�ghts green.) • The Pr�or�ty A channel may be automat�cally selected.w Wa�t for the channel to become clear. • The channel �s busy when the LED �nd�cator l�ghts green.e Wh�le hold�ng down [PTT], speak �nto the m�crophone at

your normal vo�ce level.r Release [PTT] to return to rece�ve.

IMPORTANT: To max�m�ze the readab�l�ty of your s�gnal; 1. Pause br�efly after push�ng [PTT]. 2. Hold the m�crophone 5 to 10 cm from your mouth, then

speak �nto the m�crophone at a normal vo�ce level.

9

2 BASIC OPERATION

10

2BASIC OPERATION

12345678910111213141516

D Transmitting notes• Transmit inhibit function The transce�ver has several �nh�b�t funct�ons wh�ch restr�ct

transm�ss�on under the follow�ng cond�t�ons: - The channel �s �n the ‘Inaud�ble’ (mute) mode (“ ” (Aud�-

ble �con) does not appear.) - The channel �s busy. However, depend�ng on the pre-

programmed sett�ngs, you can transm�t when a call �s re-ce�ved that �ncludes an unmatch�ng (or match�ng) CTCSS (DTCS), colour code, or Ind�v�dual or Talkgroup ID.

- The selected channel �s a ‘rece�ve only’ channel.

• Time-out timer If cont�nuous transm�ss�on exceeds the pre-programmed

t�me-out t�mer l�m�t, the transm�ss�on �s cut off.

• Penalty timer After the transm�ss�on �s cut off by the t�me-out t�mer, trans-

m�ss�on �s further �nh�b�ted for the pre-programmed penalty t�mer per�od.

D TX code channel selectionIf the transce�ver has a key ass�gned to TX Code CH Select, the �nd�cat�on can be toggled between the operat�ng channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) �s d�splayed, [CH Up] or [CH Down] selects the TX code channel.

USING [TX CODE CH SELECT]:q Push [TX Code CH Select]— a TX code channel number

(or name) appears.w Push [CH Up] or [CH Down] to select the des�red TX code

channel.e After select�ng, push [TX Code CH Select] to set. • Return to the stand-by mode.r Push [Call] to transm�t the selected TX code.

USING [TX CODE CH UP]/[TX CODE CH DOWN]:If the transce�ver has a key ass�gned to TX Code CH Up or TX Code CH Down, the programmed TX code channel can be d�rectly selected when pushed.

11

2 BASIC OPERATION

D TX code edit (5-tone operat�on only)If the transce�ver has a key ass�gned to TX Code CH Select or TX Code Enter, TX code contents can be ed�ted w�th�n the allowable d�g�ts.

USING [TX CODE CH SELECT]:q Push [TX Code CH Select] to enter the TX code channel

select�on mode. • Select the des�red channel before enter�ng the TX code chan-

nel select�on mode, �f necessary.w Hold down [TX Code CH Select] for 1 second to enter the

TX code ed�t mode. • The d�g�t to be ed�ted bl�nks.e Push [TX Code CH Select] to select the des�red d�g�t to

be ed�ted.r Push [CH Up] or [CH Down] to set the des�red d�g�t.t Push [TX Code CH Select] to set. The d�g�t to the r�ght w�ll

automat�cally bl�nk.y Repeat steps r and t to ed�t all allowable d�g�ts.u After ed�t�ng, push [TX Code CH Select] to set. • Return to the stand-by mode.i Push [Call] to transm�t.

USING [TX CODE ENTER]:q Push [TX Code Enter] to enter the TX code ed�t mode. • The d�g�t to be ed�ted bl�nks.w Push [TX Code Enter] to select the des�red d�g�t to be ed-

�ted.e Push [CH Up] or [CH Down] to select the des�red d�g�t.r Push [TX Code Enter] to set. The d�g�t to the r�ght w�ll au-

tomat�cally bl�nk.t Repeat steps e and r to �nput all allowable d�g�ts.y After ed�t�ng, push [TX Code Enter] to set. • Return to the stand-by mode.u Push [Call] to transm�t.

D DTMF transmissionIf the transce�ver has a key ass�gned to DTMF Autod�al, the automat�c DTMF transm�ss�on funct�on �s ava�lable. Up to 8 DTMF channels are selectable.

q Push [DTMF Autod�al]— a DTMF channel appears.w Push [CH Up] or [CH Down] to select the des�red DTMF

channel.e Push [DTMF Autod�al] to transm�t the DTMF code.

12

2BASIC OPERATION

12345678910111213141516

■User Set modeThe User Set mode can be accessed w�th the Power ON funct�on. In th�s case, all �tems are selectable.The User Set mode allows you to set seldom-changed set-t�ngs and you can “custom�ze” the transce�ver operat�on to su�t your preferences and operat�ng style.

NOTE: Wh�le �n the User Set mode, [Up], [Down] and [P0] act�vate regardless of the ass�gned key funct�ons.

Entering the User Set mode:q Wh�le hold�ng down [P1] and [P2], push [ ] to turn the

power ON. • Turn the power OFF first. • You should hold down [P1] and [P2] unt�l “SET MODE” appears

on the d�splay.

[P1] [P2] [ ]

w Hold down [P0] for 1 second to enter the User Set mode.

[P0]

e Push [P0] several t�mes to select the appropr�ate �tem. Then, push [Up] or [Down] to set the des�red value or set-t�ng.

• Ava�lable User Set mode �tems are Backlight, LCD Contrast, Beep, Beep Level, Ringer Level, SQL Level, AF Min Level, Mic Gain, Battery Voltage, Horn, Signal Moni, Lone Worker and System Info.

[P0] [Up]/[Down]

r Hold down [ ] for 1 second to turn the power OFF, then turn the power ON aga�n to ex�t the User Set mode.

[ ]

The User Set mode �s also ava�lable us�ng a programmable key. Please refer to page 7 [User Set Mode] sect�on for �n-struct�ons regard�ng us�ng the key ass�gned to the User Set Mode.[User Set Mode] allows for qu�ck �tem select�on. Set “Enable” for the often used �tems us�ng the CS-F3160/F5060 (dPMR) cloning software. Ask your dealer for deta�ls.

13

2 BASIC OPERATION

■ Emergency transmissionWhen [Emergency] �s held down for the pre-programmed t�me per�od, the emergency call �s transm�tted once, or repeat-edly*, on the spec�fied emergency channel.* Depend�ng on the pre-programmed sett�ngs.

A repeat emergency call �s automat�cally transm�tted unt�l you turn the power OFF. Depend�ng on the pre-programmed sett�ngs, rece�v�ng a match�ng 5-tone code cancels the trans-m�ss�on.

When no emergency channel �s spec�f�ed, the call �s trans-m�tted on the operat�ng channel.If you want to cancel the Emergency funct�on, hold down [Emergency] for the pre-programmed t�me per�od aga�n be-fore transm�tt�ng the call.

If your transce�ver �s programmed for S�lent operat�on, you can transm�t emergency calls w�thout the beep sound�ng and the LED �nd�cator l�ght�ng.

IMPORTANT: We recommend that you have an emer-gency channel to prov�de rel�able emergency calls. Ask your dealer for deta�ls.

D NOTESDepend�ng on the pre-programmed sett�ngs, the follow�ng funct�ons are automat�cally act�vated.

• Auto TX function After an emergency call transm�ss�on, aud�o from the m�cro-

phone �s automat�cally transm�tted for the pre-programmed t�me per�od.

• The HM-148G or HM-152 hand microphone �s requ�red.

• Auto RX function The transce�ver stands by �n the ‘Aud�ble’ (unmute) mode

for the pre-programmed t�me per�od, after the emergency call transm�ss�on.

14

2BASIC OPERATION

12345678910111213141516

■ Scrambler functionThe Vo�ce Scrambler funct�on prov�des pr�vate commun�ca-t�on between stat�ons. All vers�ons have a bu�lt-�n frequency �nvers�on type scrambler. Moreover, the opt�onal Roll�ng or Non-roll�ng type can be used.

➥ Push [Scrambler] to turn the Vo�ce Scrambler funct�on ON or OFF.

• “ ” appears when the funct�on �s ON.

■ Stun functionThe d�spatcher can send a s�gnal that w�ll stun, k�ll or rev�ve your transce�ver.When a Stun command �s rece�ved, the transce�ver becomes unusable. In that case, rece�v�ng a Rev�ve command or �nput-t�ng the password* (p. 8) �s necessary to operate the trans-ce�ver aga�n.When a K�ll command �s rece�ved, the transce�ver becomes unusable (the transce�ver sw�tches to the clon�ng requ�red cond�t�on). In that case, clon�ng the transce�ver �s necessary to operate the transce�ver aga�n.* Depend�ng on the pre-programmed sett�ngs.

See the operat�ng gu�de for deta�ls of the Stun funct�on w�th the BIIS and dPMR system operat�ons. Ask your dealer for deta�ls.

■ Priority A channel selectionWhen one of the follow�ng operat�ons �s performed, the transce�ver automat�cally selects the Pr�or�ty A channel.

• Turning the power ON The Pr�or�ty A channel �s selected each t�me the trans-

ce�ver power �s turned ON.

• Auto Reset The Pr�or�ty A channel �s selected when the Auto Reset

t�mer ends.

• OFF hook The Pr�or�ty A channel �s selected when you take the m�-

crophone OFF hook.

1515

2 BASIC OPERATION

■ Forced Narrow functionDepend�ng on the pre-programmed sett�ngs, you can turn the Forced Narrow funct�on ON or OFF.When the funct�on �s ON, the channel w�dth becomes Narrow regardless of the channel sett�ng, the [W�de/Narrow] key op-erat�on, repeater sett�ng, or PC control command.

To act�vate or cancel the Forced Narrow funct�on, turn the power ON wh�le hold�ng down both [P1] and [PTT].

Depend�ng on the pre-programmed sett�ngs, the Forced Nar-row funct�on �s �n�t�ally turned ON by your dealer.

■ Automatic Key Lock functionWhen the transce�ver has a key ass�gned to Lock, the Auto-mat�c Key Lock funct�on can be used.When no operat�on occurs dur�ng the pre-programmed t�me per�od, the funct�on automat�cally act�vates the Key Lock funct�on.

When the Key Lock funct�on �s ON, hold down [Lock] unt�l “LOCK OFF” �s d�splayed to turn �t OFF.

■ Power Off Emergency functionWhen the transce�ver has a key ass�gned to Power OFF Emergency, you can use the funct�on.Th�s funct�on makes the transce�ver transm�t emergency calls, even though �t appears to be powered OFF.

To act�vate the Power OFF Emergency funct�on, turn the power OFF wh�le hold�ng down [Power OFF Emergency].

When the funct�on �s act�vated, any key operat�on, the ON/OFF Hook and Lone Worker funct�ons become �nval�d. The beep, LED �nd�cator, d�splay and speaker are turned OFF as well.

On the other hand, the transce�ver can transm�t emergency calls accord�ng to the pre-programmed emergency sett�ngs.Depend�ng on the pre-programmed sett�ngs, the Amb�ence L�sten�ng funct�on can also be used. (dPMR operat�on only)

To cancel the Power OFF Emergency funct�on and restore the transce�ver, turn the power ON.

16

23

16

3CONNECTION AND MAINTENANCE

1

45678910111213141516

■ Rear panel connectionD For mobile operation

Black

Red

12VBattery

q

D-Sub 25-pinConnect to external equipment.

t

r

y

Optional speaker

e

w

Microphone

ANTENNA CONNECTORConnects to the antenna. Ask your dealer about antenna selection and placement.

EXTERNAL SPEAKER JACKConnect a 4–8 ø external speaker.

eq

w

MICROPHONE HANGERConnect the supplied microphone hanger to the vehicle’s ground for the ON/OFF Hook functions. (See page 1)

IGNITION LEADConnects to an ignition line.R

DC POWERRECEPTACLEConnects to a 12 V DC battery. Pay atten-tion to polarities.

Do not put a pressure to this lead.Binding to the DC power cable is recommended.

r

t

y

SolderCrimp

NOTE: Use the terminals as shownbelow for the cable connections.

Antenna

R WARNING! NEVER connect to a 24 V bat-tery. This could dam-age the transceiver.

R WARNING! NEVER remove the fuse-holders from the DC power cable.

17

3 CONNECTION AND MAINTENANCE

■ Rear panel connect�on (Cont�nued)

D For base station operation

ANTENNA CONNECTOR

IGNITION LEAD

D-Sub 25-pinConnect to external equip-ment.

MICROPHONE HANGERConnect the supplied mi-crophone hanger to ground for the ON/OFF Hook func-tions. (See page 1)

EXTERNAL SPEAKER JACKConnect a 4–8 ø external speaker.

DC POWERRECEPTACLEConnects to a 13.2 V DC power supply. Pay attention to polarities. Make sure the ground terminal of the DC power supply is grounded.

q

w

r

Optional speaker

e

t

Microphone

y

To the antenna

DC powersupply 13.2 V

to anACoutlet

Fuses10 A

Black

Red

q

w

e

r

t

y

R WARNING! NEVER remove the fuse-holders from the DC power cable.

18

3CONNECTION AND MAINTENANCE

12345678910111213141516

■ Supplied accessories ■ Mounting the transceiverThe un�versal mount�ng bracket suppl�ed w�th your trans-ce�ver allows overhead or dashboard mount�ng.• Mount the transce�ver securely w�th the 4 suppl�ed screws

to a th�ck surface wh�ch can support more than 1.5 kg.

Flat washer

Felt*

Spring washer

When usingself-tapping screws

Felt*

*Felt reduces the effects of vibration.

Microphone Microphone hanger and screw set

Microphone hanger cable

DC power cable Sponges*2

Flat washers

Spring washers

Bracket bolts

Mounting screws (5×12)

Self-tapping screws (5×16)

Nuts

Function name stickers*1

*2

Used for labelling the programmable function keys according to their assinged functions.Used for optional unit installation.Ask your dealer for details.

*1

Mounting bracket

19

3 CONNECTION AND MAINTENANCE

■ AntennaA key element �n the performance of any commun�cat�on sys-tems �s the antenna. Contact your dealer about antennas and the best places to mount them.

■ Fuse replacementA fuse �s �nstalled �n each fuse holder of the suppl�ed DC power cable. If a fuse blows, or the transce�ver stops funct�on-�ng, track down the source of the problem, have �t repa�red, and replace the damaged fuse w�th a new rated one.❑ Fuse rat�ng: 10 A USE a 10 A fuse of the same type only.

■ CleaningIf the transce�ver becomes dusty or d�rty, w�pe �t clean w�th a soft and dry cloth.

DO NOT use harsh solvents such as benz�ne or al-cohol, as they damage the transce�ver surfaces.

20

3

20

■ Options• RMK-3 separation kit + OPC-607/OPC-608/OPC-609 sep-

aration cable

Allows you to �nstall the transce�ver ma�n un�t separately from the front panel for operat�ng conven�ence.

OPC-607 : 3 m OPC-608 : 8 m OPC-609 : 1.9 m

• OPC-1132A dc power cable

OPC-1132A : 3 m

• SP-10/SP-22/SP-30 external speakers

Input �mpedance : 4 ˘ Max. �nput power : 5 W (SP-10/SP-22), 40 W (SP-30) SP-10 : For all-round mob�le operat�on. SP-22 : Compact and easy-to-�nstall. SP-30 : H�gh �nput power level.

• HM-152/HM-152T/HM-148G/HM-148T hand microphones

HM-152 : Hand m�crophone HM-152T : DTMF m�crophone HM-148G : Self ground�ng heavy duty m�crophone HM-148T : Self ground�ng heavy duty m�crophone w�th 10-

keypad The 10-keypad of th�s m�crophone can be used

for the DTMF code transm�ss�on only.

• SM-25 desktop microphone

• UT-96R 5tone unit

Prov�des 5-tone decoder capab�l�t�es.

• UT-108R dtmf decoder unit

Prov�des DTMF decoder capab�l�t�es.

• UT-109R/UT-110R scrambler units

Non-roll�ng type (UT-109R)/Roll�ng type (UT-110R) vo�ce scrambler un�t prov�des h�gh commun�cat�on secur�ty.

Approved Icom opt�onal equ�pment �s des�gned for opt�mal performance when used w�th an Icom transce�ver.Icom �s not respons�ble for the destruct�on or damage to an Icom transce�ver �n the event �t �s used w�th equ�pment that �s not manufactured or approved by Icom.

Some opt�ons may not be ava�lable �n some countr�es. Please ask your dealer for deta�ls.

3CONNECTION AND MAINTENANCE

12

45678910111213141516

2121

The IC-F5062D and IC-F6062D comply w�th the essent�al requ�rements of the European Rad�o and Telecommun�cat�on Term�nal D�rec-t�ve 1999/5/EC.

Th�s warn�ng symbol �nd�cates that th�s equ�p-ment operates �n non-harmon�sed frequency bands and/or may be subject to l�cens�ng cond�-t�ons �n the country of use. Be sure to check that you have the correct vers�on of th�s rad�o or the correct programm�ng of th�s rad�o, to comply w�th nat�onal l�cens�ng requ�rement.

Type-designation

DECLARATIONOF CONFORMITY

We Icom Inc. Japan1-1-32, Kamiminami, Hirano-kuOsaka 547-0003, Japan

Kind of equipment : VHF TRANSCEIVER

Signature

Authorized representative name

Place and date of issue

Declare on our sole responsibility that this equipment complies with theessential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential TestSuite measurements have been performed.

Version (where applicable):

This compliance is based on conformity with the following harmonised standards, specifications or documents:i)ii)iii)iv)v)vi)vii)

136–174 MHz 12.5 KHz/25 KHz136–174 MHz 12.5 KHz/20 KHz136–174 MHz 6.25 KHz

Düsseldorf 15th Feb. 2008

Y. FurukawaGeneral Manager

EN 60950-1 2001EN 301 489-1 v1.4.1 (August 2002) EN 301 489-5 v1.3.1 (August 2002) EN 300 086-2 v1.1.1 (March 2001) EN 300 219-2 v1.1.1 (March 2001)EN 300 113-2 v1.3.1 (December 2003)EN 301 166-2 v1.1.1 (December 2001)

(Variant name

4 DOC

22

4

DECLARATIONOF CONFORMITY

We Icom Inc. Japan1-1-32, Kamiminami, Hirano-kuOsaka 547-0003, Japan

Signature

Authorized representative name

Place and date of issue

Declare on our sole responsibility that this equipment complies with theessential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential TestSuite measurements have been performed.

Version (where applicable):

This compliance is based on conformity with the following harmonised standards, specifications or documents:i)ii)iii)iv)v)vi)vii)

400–470 MHz 12.5 KHz/25 KHz400–470 MHz 12.5 KHz/20 KHz400–470 MHz 6.25 KHz

Y. FurukawaGeneral Manager

Düsseldorf 15th Feb. 2008

EN 60950-1 2001EN 301 489-1 v1.4.1 (August 2002) EN 301 489-5 v1.3.1 (August 2002) EN 300 086-2 v1.1.1 (March 2001) EN 300 219-2 v1.1.1 (March 2001)EN 300 113-2 v1.3.1 (December 2003)EN 301 166-2 v1.1.1 (December 2001)

Type-designation

Kind of equipment : UHF TRANSCEIVER

(Variant name

123

5678910111213141516

4DOC

23

4 DOC

• List of Country codes (ISO 3166-1)Country Codes Country Codes

123456789

1011121314151617

Austr�aBelg�umBulgar�aCroat�aCzech Republ�cCyprusDenmarkEston�aF�nlandFranceGermanyGreeceHungaryIcelandIrelandItalyLatv�a

ATBEBGHRCZCYDKEEFIFRDEGRHUISIEITLV

18192021222324252627282930313233

L�echtenste�nL�thuan�aLuxembourgMaltaNetherlandsNorwayPolandPortugalRoman�aSlovak�aSloven�aSpa�nSwedenSw�tzerlandTurkeyUn�ted K�ngdom

LILTLUMTNLNOPLPTROSKSIESSECHTRGB

About e-marking: Deta�led �nstallat�on notes for Icom mob�le transce�vers to be fitted �nto veh�cles are ava�lable. Please contact your Icom dealer or d�str�butor.

MEMO

12345678910111213141516

MEMO

MEMO

12345678910111213141516

1-1-32 Kam�m�nam�, H�rano-ku, Osaka 547-0003, Japan

< Intended Country of Use >ATFIITPLGBRO

BEFRLVPTISTR

CYDELTSKLIHR

CZGRLUSINO

DKHUMTESCH

EEIENLSEBG

A-6841H-1EUPr�nted �n Japan© 2010 Icom Inc.

Pr�nted on recycled paper w�th soy �nk.