TWS Sec_G

G

Cable&

Connectors

© 1996 TELEWIRE SUPPLYG1

SOUTHEAST: Norcross, GA 800-433-3765 EAST: Rockaway, NJ 800-458-4524 MIDWEST: Rolling Meadows, ILSOUTHWEST: Irving, TX 800-643-2288 WEST: Santa Ana, CA 800-227-2869 800-428-7596

G

Cable & ConnectorsContents Page

About Cable & ConnectorsThe cables and connectors listed in this section meet the high-est standards of quality control in the industry. All trunk andfeeder cables are specified to at least 1 GHz, 30 dB structuralreturn loss (SRL); all drop cables are specified to 1 GHz, 20 dBSRL, and all connectors are specified to 1 GHz. These prod-ucts are utilized extensively in all cable television systemsincluding private homes, banks, factories, hotels, motels, hos-pitals, apartment complexes, government and military facilities,and many more areas of application.

Telewire Supply provides products from such quality manu-

Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page

About Trunk Cable . . . . . . . . . . . . . . . . . . . . . . . . . .G2

.500 Trunk Cable . . . . . . . . . . . . . . . . . . . . . . . .G3-G4

.625 Trunk Cable . . . . . . . . . . . . . . . . . . . . . . . .G5-G6

.750 Trunk Cable . . . . . . . . . . . . . . . . . . . . . . . .G7-G8

.875 Trunk Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .G9

1.00 Trunk Cable . . . . . . . . . . . . . . . . . . . . . . . . . .G10

.540 QR Trunk Cable . . . . . . . . . . . . . . . . . . . . . . .G11

.715 QR Trunk Cable . . . . . . . . . . . . . . . . . . . . . . .G12

.860 QR Trunk Cable . . . . . . . . . . . . . . . . . . . . . . .G13

1.125 QR Trunk Cable . . . . . . . . . . . . . . . . . . . . . .G14

Trunk Cable Weights . . . . . . . . . . . . . . . . . . . . . . .G15

Trunk Cable Information . . . . . . . . . . . . . . . . . . . .G16

Drop Cable Specifications . . . . . . . . . . . . . . .G17-G19

RG59 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G20

RG6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G21

RG7, RG11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G22

Wireless/DBS Cable . . . . . . . . . . . . . . . . . . . . . . . .G23

Headend Cables . . . . . . . . . . . . . . . . . . . . . . . . . .G24

Audio / Telephone Cable . . . . . . . . . . . . . . . . . . . .G25

Connector Types . . . . . . . . . . . . . . . . . . . . . . . . . .G26

Telewire Supply is dedicated to meeting the requirements ofour customers by providing Quality Products and Services ona timely basis.

Quality Policy

In this section

facturers to the cable TV industry as Belden, Comm/Scope,Gilbert, LRC, Amphenol, Cablecom and many more.Equipment is regionally warehoused across the country, pro-viding for complete system fulfillments and on-time delivery.

This section is devised as a buyer's guide only and is notintended to be a design or installation guide.

Gilbert Quick Reference . . . . . . . . . . . . . . . .G27-G28

LRC Quick Reference . . . . . . . . . . . . . . . . . .G29-G30

.412 Connectors . . . . . . . . . . . . . . . . . . . . . . .G32-G33

.500 Connectors . . . . . . . . . . . . . . . . . . . . . . .G34-G35

.540 QR Connectors . . . . . . . . . . . . . . . . . . . . . . .G36

.625 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . .G37

.650 MC2 Connectors . . . . . . . . . . . . . . . . . . . . . . .G38

.700 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . .G38

.715 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . .G39

.750 Connectors . . . . . . . . . . . . . . . . . . . . . . .G40-G41

.840, .860 Connectors . . . . . . . . . . . . . . . . . . . . . .G42

.875, 1.00 Connectors . . . . . . . . . . . . . . . . . . . . . .G43

1.125 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . .G44

Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G45-G49

Heat Shrink . . . . . . . . . . . . . . . . . . . . . . . . . .G50-G51

Digicon Connector . . . . . . . . . . . . . . . . . . . . . . . . .G52

EZF Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . .G53

"F" Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . .G54

F-81 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . .G55

50 Ohm Connectors . . . . . . . . . . . . . . . . . . . . . . . .G56

Drop Cable Cross Reference . . . . . . . . . . . .G57-G59

G

Cable & ConnectorsTrunk Cables

Trunk CablesCOMM/SCOPE

DescriptionThe application of coaxial cables to underground installationsshould be undertaken with caution because of the many haz-ards existing that can damage the cable both during and afterplacement. These hazards are also a major consideration inselecting the cable for underground use. Any vehicle that canprevent damage to the aluminum shield and center conductorshould be a requirement, not an option.

Some forms of damage could be cuts in the jacket caused bysharp rocks or debris, dents caused by rocks or rough handlingduring installation, and/or corrosion caused by moisture andcorrosive elements in the ground.

There are several styles of coaxial cables available fromwhich to select the best design for each application. The fol-lowing is a description of cable design from most protectionto least protection.

JACASS Polyethylene jacket, steel armor, flooding com-pound, polyethylene jacket, Migra-Heal® floodingcompound, aluminum conductor, dielectric adhe-sive (optional), dielectric, Double Clad® conductortreatment and center conductor.

JCASS Polyethylene jacket with shock absorbing compart-mentalized cells, Migra-Heal floodingcompound,aluminum conductor, dielectric adhe-sive, dielectric, Double Clad conductor treatmentand center conductor.

JCASS Polyethylene jacket, Migra-Heal flooding com-pound, aluminum conductor, dielectricadhesive(optional), dielectric, Double Clad conduc-tor treatment and center conductor.

JCASP Polyethylene jacket, asphalticflooding compound,aluminum conductor, dielectric adhesive (optional),dielectric, Double Clad conductor treatment andcenterconductor.

JCA Polyethylene jacket, aluminum conductor, dielectricadhesive (optional), dielectric, Double Clad conduc-tor treatment and centerconductor

CA Aluminum conductor, dielectric adhesive (optional),dielectric, Double Clad conductor treatment and cen-ter conductor

Packaging Information

Standard lengthsParameter III®, Cable Guard and Plenum

.500 in. (12.7mm) 2,400 ft. (732 meters)

.625 in. (15.8mm) 2,400 ft. (732 meters)

.750 in. (19.1mm) 2,500 ft. (762 meters)

.875 in. (22.2mm) 2,500 ft. (762 meters)

1.00 in. (25.4mm) 2,400 ft. (732 meters)

Quantum Reach®

.540 in. (13.72mm) 3,700 ft. (1128 meters)

.715 in. (18.16mm) 3,000 ft. (914 meters)

.860 in. (21.84mm) 2,700 ft. (823 meters)

1.125 in. (28.58mm) 3,000 ft. (914 meters)

All cable products 100% sweep tested.Each shipment shall be standard lengths ±10%.

© 1996 TELEWIRE SUPPLY G2


Prefixes

P3 Parameter III

75 impedance

500, 540, 625, 750,860, 875, 1000, 1125 trunk and feeder cable series

QR Quantum Reach

Suffixes

J polyethylene jacket

A armor

CA copper clad aluminum center conductor

SS Migra-Heal flooding compound

SP asphaltic flooding compound

M messenger

109, 134, 250 messenger size

P foamed teflon dielectric, plenum listed

R riser listed

Cable Guard shock absorbing compartmentalized cell jacket

Cable Guard®

G

Cable & ConnectorsTrunk Cable

.500 Parameter III® SeriesCopper Clad Aluminum SheathCOMM/SCOPE

Bare

Copper clad aluminum center conductor; expanded polyethy-lene dielectric; solid aluminum sheath; center conductor 0.111"(2.82mm) nominal; nom. O.D. 0.500" (12.70mm).

Ordering Information

Order Mfg.No. No. DescriptionCSP 202204 P3 75-500CA Bare

CSP 202205 P3 75-500JCA Jacketed

CSP 202206 P3 75-500JCASS Jacketed with Flooding Compound

CSP 202207 P3 75-500JCASSCG Cable Guard®Jacketed with Flooding Compound

CSP 202208 P3 75-500JACASS Jacketed with Steel Armor & Flooding Compound

CSP 202209 P3 75-500JCAM109 Jacketed with Steel Messenger

Jacketed

Similar in construction to P3 75-500CA, except with 0.030"(0.76mm) outer jacket of black medium density polyethylene.Nominal O.D. 0.560" (14.22mm).

Jacketed with Flooding Compound

Similar in construction to P3 75-500JCA, except with Migra-Heal® compound between jacket and aluminum sheath

Cable Guard® Jacketed with Flooding Compound

Similar in construction to P3 75-500JCASS. The unique jacketdesign is a medium density polyethylene material .125" thick con-sisting of a 30 mils inner jacket, 75 mils high webbed air cells anda 30 mils outer jacket.

Jacketed with Steel Armor

Similar to P3 75-500JCASS, except with 0.006" (0.15mm) cor-rugated chrome plated steel armor applied longitudinally, coat-ed on outside with 0.002" (0.05mm) heat sealable film whichbonds to outer jacket and seals edges to form an effective mois-ture barrier and provide mechanical protection. Nominal O.D.0.715" (18.16mm).

Jacketed with Steel Messenger

Similar to P3 75-500JCA, except with "Figure 8" constructionwith 0.109" (2.77mm) galvanized steel messenger.





G

Cable & ConnectorsTrunk Cable - .500PIII Series


Physical Dimensions

Center Conductor Diameter 0.111" ±0.001" (2.82mm ±0.03mm)

Nominal Diameter Over Dielectric 0.450" (11.43mm)

Diameter Over Outer Conductor 0.500 ±0.007" (12.70mm ±0.18mm)

Nominal Outer Conductor Thickness 0.025" (0.64mm)

Nominal Diameter Over Jacket 0.560" (14.22mm)

Nominal Jacket Wall Thickness 0.030" (0.76mm)

Nominal Diameter Over Corrugated Armor 0.635" (16.13mm)

Nominal Shield Thickness 0.008" (0.20mm)

Nominal Diameter Over Outer Jacket 0.715" (18.16mm)

Nominal Thickness of Outer Jacket 0.040" (1.02mm)

Diameter of Steel Messenger 0.109" (2.77mm)

Mechanical Characteristics

Minimum Bending Radius Without Armor 8.0" (20.3cm)With Armor 10.5" (26.7cm)

Pulling Tension 200 lbs. (91 kg)

Minimum Breaking Strength of Messenger 1,800 lbs. (816 kg)

Electrical Characteristics

Capacitance 15.3 ±1.0 pf/ft. (50 ±3 nf/km)

Impedance 75 ±2 ohms

Velocity of Propagation 87%

Maximum of DC Resistance @ 68°F (20°C) Inner Conductor 1.35 ohms/1000’ (4.40 ohms/km) Outer Conductor 0.37 ohms/1000’ (1.24 ohms/km) Loop 1.72 ohms/1000’ (5.64 ohms/km)

Frequency Maximum Maximum(MHz) (db/100 ft.) (db/100 m)

5 0.16 0.52

30 0.40 1.31

45 0.49 1.61

50 0.52 1.71

55 0.54 1.77

83 0.66 2.17

108 0.75 2.46

150 0.90 2.95

181 1.00 3.28

193 1.03 3.38

211 1.09 3.58

220 1.11 3.64

250 1.20 3.94

270 1.24 4.07

300 1.31 4.30

325 1.37 4.49

350 1.43 4.69

375 1.47 4.82

400 1.53 5.02

425 1.57 5.15

450 1.63 5.35

500 1.73 5.67

550 1.82 5.97

600 1.93 6.33

750 2.17 7.12

865 2.34 7.68

1000 2.52 8.27

Attenuation @ 68°F (20°C)



G



Bare









Jacketed



Similar in construction to P3 75-625JCA, except with Migra-Heal® compound between jacket and aluminum sheath.


Similar in construction to P3 75-625JCASS. The unique jacketdesign is a medium density polyethylene material .125" thickconsisting of a 30 mils inner jacket, 75 mils high webbed aircells and a 30 mils outer jacket. Nominal O.D. 0.875"(22.25mm).







G



Physical Dimensions






















5 0.13 0.52

30 0.34 1.31

45 0.41 1.61

50 0.44 1.71

55 0.46 1.77

83 0.57 2.17

108 0.65 2.46

150 0.77 2.95

181 0.85 3.28

193 0.88 3.38

211 0.92 3.58

220 0.94 3.64

250 1.00 3.94

270 1.05 4.07

300 1.10 4.30

325 1.15 4.49

350 1.20 4.69

375 1.23 4.82

400 1.28 5.02

425 1.32 5.15

450 1.35 5.35

500 1.43 5.67

550 1.50 5.97

600 1.59 6.33

750 1.78 7.12

865 1.93 7.68

1000 2.07 8.27




G



Bare



Jacketed





Similar in construction to P3 75-750JCASS. The unique jacketdesign is a medium density polyethylene material .125" thick con-sisting of a 30 mils inner jacket, 75 mils high webbed air cells anda 30 mils outer jacket.













G



Physical Dimensions






















5 0.11 0.36

30 0.26 0.85

45 0.33 1.08

50 0.35 1.15

55 0.37 1.21

83 0.46 1.51

108 0.52 1.71

150 0.62 2.03

181 0.68 2.23

193 0.71 2.33

211 0.74 2.43

220 0.76 2.49

250 0.81 2.66

270 0.85 2.79

300 0.90 2.95

325 0.94 3.08

350 0.97 3.18

375 1.01 3.31

400 1.05 3.44

425 1.08 3.54

450 1.12 3.67

500 1.18 3.87

550 1.24 4.07

600 1.36 4.46

750 1.53 5.02

865 1.64 5.38

1000 1.78 5.84




G



Bare



Order Mfg.No. No. Description

CSP 202222 P3 75-875CA Bare




Jacketed






Frequency Maximum Maximum Frequency Maximum Maximum(MHz) (db/100 ft.) (db/100 m) (MHz) (db/100 ft.) (db/100 m)

5 0.09 0.30 300 0.79 2.59

30 0.24 0.79 325 0.82 2.69

45 0.30 0.98 350 0.86 2.82

50 0.32 1.05 375 0.89 2.92

55 0.33 1.08 400 0.91 2.99

83 0.41 1.35 425 0.95 3.12

108 0.47 1.54 450 0.98 3.22

150 0.55 1.80 500 1.03 3.38

181 0.60 1.97 550 1.08 3.54

193 0.62 2.03 600 1.20 3.94

211 0.66 2.17 750 1.36 4.46

220 0.67 2.20 865 1.47 4.82

250 0.72 2.36 1000 1.59 5.22

270 0.75 2.46

Attenuation @ 68°F (20°C)Physical Dimensions





















G

Cable & ConnectorsEquipment for Line Vehicles



1.00 Parameter III® SeriesCopper Clad Aluminum SheathCOMM/SCOPE

Bare




CSP 202226 P3 75-1000CA Bare




Jacketed





Similar to P3 75-1000JCASS, except with 0.006" (0.15mm) cor-rugated chrome plated steel armor applied longitudinally, coat-ed on outside with 0.002" (0.05mm) heat sealable film whichbonds to outer jacket and seals edges to form an effective mois-ture barrier and provide mechanical protection. Nominal O.D.1.26" (32.00mm). Physical Dimensions













Minimum Bending Radius Without Armor 15" (38.1cm)With Armor 18" (45.7cm)









5 0.09 0.30 300 0.75 2.46

30 0.23 0.75 325 0.78 2.56

45 0.28 0.92 350 0.81 2.66

50 0.30 0.98 375 0.84 2.76

55 0.31 1.02 400 0.87 2.85

83 0.39 1.28 425 0.90 2.95

108 0.44 1.44 450 0.92 3.02

150 0.52 1.71 500 0.98 3.21

181 0.59 1.94 550 1.03 3.38

193 0.60 1.97 600 1.08 3.54

211 0.62 2.03 750 1.23 4.04

220 0.63 2.07 865 1.34 4.40

250 0.68 2.23 1000 1.47 4.82

270 0.71 2.33




G

Cable & ConnectorsTrunk Cable - .540 QR Series

.540 Quantum Reach® SeriesCopper Clad Aluminum SheathCOMM/SCOPE

Physical Dimensions












Minimum Bending Radius Without Armor 5.0" (12.7cm)

Maximum Pulling Tension 340 lbs. (154 kg)






Jacketed

Copper clad aluminum center conductor; Double-Clad™ cen-ter conductor treatment inhibits water migration and corrosion;dielectric with new micro cellular structure provides lowerattenuation, and dielectric adhesive inhibits water migration,connector pull-out and enhances handling characteristics; alu-minum outer conductor with continuous R.F. welded construc-tion eliminates signal leakage, with good flexibility for improvedhandling properties; medium density polyethylene jacket isstronger and tougher than conventional jackets; center con-ductor 0.124" (3.19mm) nominal; nom. O.D. .610" (15.49mm).


Similar in construction to QR-540JCA, except with Migra-Heal® flooding compound which inhibits cable corrosionin the event of severe jacket damage.

Jacketed with Flooding Compound with Steel Armor

Similar to QR-540JCASS, except with .006" (.15mm) corrugat-ed chrome plated steel armor applied longitudinally and withflooding compound between the armor and the inner jacket.Armor is bonded to the outer jacket and enhances cablelongevity in burial applications. Nominal O.D. .765" (19.43mm).



CSP 202230 QR-540JCA Jacketed

CSP 202425 QR-540JCASS Jacketed with Flooding Compound

CSP 202232 QR-540JACASS Jacketed with Flooding Compoundand Steel Armor


5 0.14 0.46 300 1.14 3.74

30 0.35 1.15 325 1.20 3.94

45 0.41 1.35 350 1.23 4.03

50 0.44 1.44 375 1.30 4.27

55 0.47 1.54 400 1.33 4.36

83 0.58 1.90 425 1.37 4.49

108 0.67 2.20 450 1.41 4.63

150 0.79 2.59 500 1.50 4.92

181 0.88 2.89 550 1.58 5.18

193 0.90 2.95 600 1.66 5.45

211 0.95 3.12 750 1.86 6.10

220 0.98 3.22 865 2.00 6.56

250 1.03 3.38 1000 2.17 7.12

270 1.08 3.54




G



Physical Dimensions



















Jacketed

Copper clad aluminum center conductor; Double-Clad™ cen-ter conductor treatment inhibits water migration and corrosion;dielectric with new micro cellular structure provides lower atten-uation, and dielectric adhesive inhibits water migration, con-nector pull-out and enhances handling characteristics; alu-minum outer conductor with continuous R.F. welded construc-tion eliminates signal leakage, with good flexibility for improvedhandling properties; medium density polyethylene jacket isstronger and tougher than conventional jackets; center con-ductor 0.166" (4.22mm) nominal; nom. O.D. 0.785" (19.94mm).


Similar to QR-715JCA, except with Migra-Heal® floodingcompound which inhibits cable corrosion in the event ofsevere jacket damage.


Similar to QR-715JCASS, except with .006" (.15mm) corrugatedchrome plated steel armor applied longitudinally and with flood-ing compound between the armor and the inner jacket. Armor isbonded to the outer jacket and enhances cable longevity in buri-al applications. Nominal O.D. 0.935" (23.75mm).







5 0.11 0.36 300 0.89 2.92

30 0.27 0.89 325 0.94 3.08

45 0.33 1.08 350 0.97 3.18

50 0.35 1.15 375 1.01 3.31

55 0.36 1.18 400 1.05 3.44

83 0.45 1.48 425 1.09 3.58

108 0.51 1.67 450 1.12 3.67

150 0.61 2.00 500 1.19 3.90

181 0.68 2.23 550 1.26 4.13

193 0.70 2.30 600 1.32 4.33

211 0.74 2.43 750 1.50 4.92

220 0.76 2.49 865 1.64 5.38

250 0.81 2.66 1000 1.78 5.84

270 0.84 2.76




G



Physical Dimensions



















Jacketed

Copper clad aluminum center conductor; Double-Clad centerconductor treatment inhibits water migration and corrosion;dielectric with new micro cellular structure provides lower atten-uation, and dielectric adhesive inhibits water migration, con-nector pull-out and enhances handling characteristics; alu-minum outer conductor with continuous R.F. welded construc-tion eliminates signal leakage, with good flexibility for improvedhandling properties; medium density polyethylene jacket isstronger and tougher than conventional jackets; center con-ductor 0.203" (5.16mm) nominal; nom. O.D. 0.940" (23.88mm).


Similar in construction to QR-860JCA, except with Migra-Heal®flooding compound which inhibits cable corrosion in the event ofsevere jacket damage.


Similar to QR-860JCASS, except with .006" (.15mm) corrugat-ed chrome plated steel armor applied longitudinally and withflooding compound between the armor and the inner jacket.Armor is bonded to the outer jacket and enhances cablelongevity in burial applications. Nominal O.D. 1.115" (28.32mm).







5 0.09 0.30 300 0.76 2.49

30 0.24 0.79 325 0.80 2.62

45 0.29 0.95 350 0.83 2.72

50 0.31 1.02 375 0.86 2.82

55 0.32 1.05 400 0.88 2.89

83 0.40 1.31 425 0.92 3.02

108 0.46 1.51 450 0.95 3.12

150 0.54 1.77 500 1.00 3.28

181 0.59 1.94 550 1.06 3.48

193 0.60 1.97 600 1.10 3.61

211 0.64 2.10 750 1.24 4.07

220 0.65 2.13 865 1.33 4.36

250 0.70 2.30 1000 1.44 4.72

270 0.72 2.36




G


1.125 Quantum Reach® SeriesCopper Clad Aluminum SheathCOMM/SCOPE

Physical Dimensions









Nominal Diameter Over Outer Jacket 1.380 (35.05mm)










Jacketed

Copper clad aluminum center conductor; Double-Clad centerconductor treatment inhibits water migration and corrosion;dielectric with new micro cellular structure provides lower atten-uation, and dielectric adhesive inhibits water migration, con-nector pull-out and enhances handling characteristics; alu-minum outer conductor with continuous R.F. welded construc-tion to eliminate signal leakage, with good flexibility forimproved handling properties; medium density polyethylenejacket is stronger and tougher than conventional jackets; cen-ter conductor 0.263" (6.68mm) nominal; nom. O.D. 1.225"(31.12mm).


Similar in construction to QR-1125JCA, except with Migra-Heal®flooding compound which inhibits cable corrosion in the event ofsevere jacket damage.


Similar to QR-1125JCASS, except with 1.30" (.33.02mm) cor-rugated chrome plated steel armor applied longitudinally andwith flooding compound between the armor and the inner jack-et. Armor is bonded to the outer jacket and enhances cablelongevity in burial applications. Nominal O.D. 1.380" (35.5mm).







5 0.07 0.23 300 0.60 1.97

30 0.17 0.56 325 0.61 2.00

45 0.21 0.69 350 0.65 2.13

50 0.22 0.72 375 0.68 2.23

55 0.23 0.76 400 0.70 2.30

83 0.29 0.95 425 0.73 2.40

108 0.34 1.12 450 0.75 2.46

150 0.41 1.35 500 0.80 2.62

181 0.45 1.48 550 0.84 2.76

193 0.47 1.54 600 0.90 2.95

211 0.49 1.61 750 1.07 3.51

220 0.50 1.64 865 1.17 3.84

250 0.54 1.77 1000 1.28 4.20

270 0.56 1.84




G

Cable & ConnectorsFire Safety Requirements

CommScope PIII & QR Cable Weights

Standard Reel Cable Weight Reel Size EmptyDescription Length (feet) lbs/1000' (Inches) Reel WeightP3 75-500 CA 2,400 71 35" x 16" x 18" 60 lbs

P3 75-500JCA 2,400 95 35 x 16 x 18 60 lbs

P3 75-500 JCASS 2,400 99 35 x 16 x 46 60 lbs

P3 75-500 JACASS 2,400 209 42 x 24 x 24 94 lbs

P3 75-500 JCAM-109 2,400 133 42 x 18 x 16.5 94 lbs

P3 75-625 CA 2,400 114 42 x 24 x 24 94 lbs

P3 75-625 JCA 2,400 139 42 x 24 x 24 94 lbs

P3 75-625 JCASS 2,400 143 42 x 24 x 24 94 lbs

P3 75-625 JACASS 2,400 281 50 x 24 x 24 166 lbs

P3 75-625 JCAM-109 2,400 178 50 x 24 x 24 166 lbs

P3 75-750 CA 2,500 162 50 x 24 x 24 166 lbs

P3 75-750 JCA 2,500 197 50 x 24 x 24 166 lbs

P3 75-750 JCASS 2,500 205 50 x 24 x 24 166 lbs

P3 75-750 JACASS 2,500 360 54 x 24 x 24 208 lbs

P3 75-750 JCAM-250 2,500 345 54 x 30 x 30 300 lbs

P3 75-875 CA 2,500 216 55 x 30 x 24 211 lbs

P3 75-875 JCA 2,500 257 55 x 30 x 24 211 lbs

P3 75-875 JCASS 2,500 263 55 x 30 x 24 211 lbs

P3 75-875 JACASS 2,500 441 63 x 40 x 26 304 lbs

P3 75-1000 CA 2,400 311 63 x 40 x 26 304 lbs

P3 75-1000 JCA 2,400 365 63 x 40 x 26 304 lbs

P3 75-1000 JCASS 2,400 372 63 x 40 x 26 304 lbs

P3 75-1000 JACASS 2,400 581 65 x 42 x 30 374 lbs

Cable Guard SeriesP3 75-500 JCASS-CG 2,400 138 42 x 24 x 24 94 lbs

P3 75-625 JCASS-CG 2,400 199 50 x 24 x 24 166 lbs

P3 75-750 JCASS-CG 2,500 256 54 x 30 x 30 300 lbs

QR 75-540 JCA 3,700 92 42 x 24 x 24 94 lbs

QR 75-540 JCASS 3,700 92 42 x 24 x 24 94 lbs

QR 75-540 JACASS 3,700 207 50 x 24 x 24 166 lbs

QR 75-540 JCAM-109 3,700 132 50 x 24 x 24 166 lbs

QR 75-715 JCA 3,000 145 50 x 24 x 20 182 lbs

QR 75-715 JCASS 3,000 145 50 x 24 x 20 182 lbs

QR 75-715 JACASS 3,000 288 54 x 30 x 24 211 lbs

QR 75-715 JCAM-188 3,000 233 54 x 24 x 24 208 lbs

QR 75-860 JCA 2,700 213 54 x 24 x 24 208 lbs

QR 75-860 JCASS 2,700 214 54 x 24 x 24 208 lbs

QR 75-860 JACASS 2,700 393 61 x 30 x 24 256 lbs

QR 75-860 JCAM-188 2,700 309 61 x 30 x 30 25 lbs

QR 75-1125 JCA 3,000 341 61 x 30 x 30 256 lbs

QR 75-1125 JCASS 3,000 341 61 x 30 x 30 256 lbs

QR 75-1125 JACASS 3,000 571 72 x 40 x 38 375 lbs



G

Cable & ConnectorsCable Specifications

Quantity of Cable Remaining on a ReelCOMM/SCOPE

The amount of cable on a standard sizereel may be estimated by counting the lay-ers of cable and multiplying the number oflayers by the length per layer. These esti-mates are presented as the closest fulllayer of cable.

P-3 Products

(In Feet)

Layers 500 500J 625 625J 750 750J 875 875J 1000 1000J1 150 125 225 200 250 225 250 225 175 165

2 300 250 500 425 500 450 500 450 350 340

3 475 400 750 675 775 700 775 700 550 540

4 650 550 1050 925 1050 975 1075 975 750 735

5 825 700 1325 1175 1350 1250 1375 1250 975 960

6 1025 875 1650 1450 1675 1525 1700 1525 1200 1180

7 1250 1050 1950 1750 2000 1825 2025 1825 1450 1430

8 1450 1250 2300 2050 2325 2150 2350 2150 1700 1675

9 1675 1450 2400 2350 2500 2475 2500 2450 1975 1950

10 1925 1650 2400 2500 2500 2250 2225

11 2175 1875 2400 2400

12 2400 2100

13 2400

QR Products

Layers 540J 715J 860J 1125J1 230 160 225 245

2 525 331 450 490

3 775 512 700 735

4 1075 704 975 985

5 1350 906 1250 1235

6 1675 1118 1525 1485

7 1975 1341 1825 1735

8 2325 1575 2150 1985

9 2650 1819 2450 2240

10 2950 2074 2700 2495

11 3300 2340 2750

12 3700 2615 3000

13 2900

14 3000

Truckload Quantity of Coaxial Cable

Reel No. Reel Truckload Size Type Reels Product XLengths =Qty.

35" Bare 152 500 2,450 370,000

35" Bare 152 412 3,000 450,000

35" Jacketed 114 500J 2,450 275,000

35" Jacketed 114 412J 3,000 350,000

42" Armored 48 500 2,450 118,000

42" Armored 48 412 3,000 144,000

42" Messenger 72 500 2,400 176,000

42" Messenger 48 412 3,000 144,000

50" Bare 62 750 2,500 150,000

50" Jacketed 52 750J 2,500 150,000

54" Armored 30 750 2,500 75,000

42" Bare & Jacketed 72 625 2,450 175,000

55" Bare & Jacketed 36 875 2,500 90,000

63" Bare & Jacketed 20 1000 2,500 50,000

42" 72, 36* QR 500 3,700 266,000, 133,000*

42" 72, 36* QR 540 3,700 266,000, 133,000*

50" 50, 15* QR 715 3,000 150,00, 45,000*

54" 40, 17* QR 860 2,500 100,000, 42,000*

61" 17, 14* QR1125 3,000 51,000, 42,000*

*Standing Upright

Cable Standard Cable StandardSize Length (Ft.) Size Length (Ft.)

P3 500 2,400 QR 540 3,700

P3 625 2,400 QR 715 3,000

P3 750 2,500 QR 860 2,700

P3 875 2,500 QR 1125 3,000

P3 1000 2,400



G

Cable & ConnectorsCable Specifications

1990 National Electrical Code Requirements for Fire Saftey of CATV Cables

The National Electrical Code (NEC) detailing the communityantenna television and radio distribution systems is covered inArticle 820, Sections 820-1 through 820-53. These codes aresafety guidelines established by the National Fire ProtectionAssociation (NFPA). Coaxial cables installed as wiring withinbuildings shall be listed as being resistant to the spread of firein accordance with the NEC. The tables must be marked inaccordance with Table 820-50.

Although NEC covers wire and cable installed in factories,office buildings, hotels, motels, apartment buildings, resi-dences, and all cables which pass through any floor, wall, ceil-ing, or which travel in ducts, plenums, and other air handlingspaces, each individual municipality, city, county, or state candecide whether they wish to adopt the 1990 NEC as law. Therequirements established by the NEC may be adopted by thestate or local building code agencies where jurisdiction of localelectrical, building and fire inspector requirements are estab-lished and enforced. Local authorities having jurisdictionenforce their own codes. They have the right to accept orrefuse any installation in accordance with their local laws. Oneof the organizations local inspectors rely on to test wire andcable is Underwriter's Laboratories (U.L.) All applicable build-ing codes should be reviewed and electrical, building and fireinspection organizations consulted prior to the selection, instal-lation and operation of any cable products.

Article 820-4 details identification marking of cables for use inany given area. Although subject to local interpretation, themarking (printing) stipulation most likely will be a prerequisitefor installations. The 1990 NEC classifications for coaxial dropcables are as follows:

1. CATVP [Article 820-51(a), 820-53(a)] - Designed for usein ducts, plenums, and other spaces used for environ-mental air. This type of cable is commonly referred to asplenum cable and can be used in place of any of the fol-lowing three levels.

2. CATVR [Article 820-51(b), 820-53(b)] - Designed for instal-lation in vertical runs and penetrating more than one floor,or cables installed in vertical runs in a shaft. Riser cablecan be substituted for the remaining lower level flametests. CATVP cables can be substituted for CATVR appli-cations to maintain electrical integrity of the cable.

3. CATV [Article 820-51(c), 820-53(c)] - Designed for installa-tion in building locations other than the locations coveredin 1 and 2 above. These cables pass the UL1581 flametest, similar to IEEE 383, 70000 BTU tray flame test.

Cable Markings & Substitutions

Permitted Listing Type Reference SubstitutesCATVP Plenum Cable 820-51 (a) 820-53 (a) None

CATVR Riser Cable 820-51 (b) 820-53 (b) CATVP

CATV CATV Cable 820-51 (c) 820-53 (c) CATVP, CATVR

Products are listed into the above marking categories throughflame and smoke testing using Underwriters Laboratories (UL)procedures. The listing shown below is in descending order offlame test severity:

CATVP.......Plenum..................UL910, NFPA-262

CATVR ......Riser ......................UL1666

CATV .........General Purpose...UL1581

Information in this catalog has been drawn from authoritativesources in their latest available editions. National ElectricCode (NEC) is a registered trademark of the National FireProtection Association, Inc., Quincy, MA for a triennialElectrical Publication. The term National Electric Code, asused herein, means the triennial publication constituting theNational Electrical Code and is used with permission of theNational Fire Protection Association, Inc. All due concern hasbeen devoted to accuracy but TeleWire Supply cannot beresponsible for errors, omissions, or obsolescence. All dataherein are subject to change without notice. TeleWire Supplydoes not manufacture the items described herein. Users arerequested to determine directly from the manufacturer’s testsor to make their own tests to determine the suitability of thesematerials for their application and to be guided by the resultsof such tests. All applicable warranties are provided by themanufacturer. Purchasers are requested to determine directlyfrom the manufacturer the applicable product warranty andlimitations. Data and suggestions made in this publication arenot to be construed as recommendations to use any productsin violation of any government law or regulation relating to anymaterial or its use.



G

Cable & ConnectorsAbout Drop Cable

Drop Cable

About Non-Plenum Cable Certain sections of the 1987 update of the National ElectricCode make distinctions between cable for general building useand cable for restricted use. For instance, Article 725 forremote control, signaling and power limited circuits states thatgeneral building cable may run without conduit in certain con-cealed spaces (such as walls) while restricted use cable mustrun in conduit unless it is run a distance of less than 10 feet.

For most interbuilding applications, system planners shouldnote that savings can be realized by specifying CL2 cables, asthey do not require conduit. Most non-plenum Comm/Scopecables are manufactured with special jacketing and dielectricmaterials that allow them to meet the CL2 standards. UsingCL2X cables when CL2 cables are mandated may pose anunwarranted safety threat.

About Plenum CablePlenums are the enclosed air spaces in office buildings whichare used for supply or return ventilation and can house the elec-trical and communications wiring for the building. Because theair space is unobstructed, plenums represent an area where firecan spread quickly if combustible materials are present.

Prior to 1975, the National Fire Protection Agency required thatall cables running through a plenum had to be encased in con-duit. This regulation was an effort to prevent cable from addingto the heat, flames and smoke in the event of a fire.

The development of plenum cable revolutionized the way com-munication cables are installed. Plenum cable is made of fluo-ropolymers that propagate flame at a very slow rate and havelow smoke generating properties. For these reasons, plenumcables are approved by the National Fire Protection Agency tobe installed without conduit.

Although plenum cables have a higher initial cost than a similarnon-plenum cable, they cost less to install because they do notrequire conduit. They are especially resistant to cracking, abra-sion, chemicals and extreme temperatures (-40°F to +400°F).

About Multiconductor and Twisted Pair CablesMulticonductor cable is made up of two or more insulated con-ductors grouped together to make electronic wiring more prac-tical. Applications include communications, instrumentation,sound, control, audio and data transmission.

Twisted pair cable consists of wire pairs (two insulated wirestwisted around each other) grouped in a cable. The pairs ofconductors are twisted to reduce crosstalk and to decreasecapacitance unbalance. This usually allows higher dataspeeds than multiconductor cables.

Twisted pair is inexpensive and relatively easy to install. It isgaining rapid acceptance as a transmission medium for a vari-ety of networks, although these systems are presently smallerand slower than networks connected by coaxial cable.



Jacket Aluminum Aluminum Aluminum Bonded Dielectric CenterBraided Foil Braided Aluminum ConductorShield Shield Shield Foil Shield

G

Cable & ConnectorsCable Constructions

PrefixF . . . . . . . . .Foam Polyethylene Dielectric2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dual59, 6, 7, 11 . . . . . . . . .Drop Cable Series

Foam

Dual

59 Drop Cable Series

Foam


Foam


Foam

Dual


Messenger

Polyvinylchloride Jacket

Bonded

% of Braid Coverage

Flooded

Polyethylene Jacket

Bonded

% of Braid Coverage

Riser


Super-Shield

Corrosion Resistant Drop Cable


Bonded

% of Braid Coverage

SufffixFirst two digits . . . .% of Braid Coverage

(e.g. 53, 60, 67, 90,95)B . . . . . . . . . . . . . . . . . . . . . .Bonded FoilE . . . . . . . . . . . .Polyethylene Jacket (PE)V . . . . . . .Polyvinylchloride Jacket (PVC)M . . . . . . . . . . . . . . . . . . . . . . .MessengerF . . . . . . . . . . . . . . . . . . . . . . . . . .FloodedSS . . . . . . . . . . . . . . . . . . . .Super ShieldTS . . . . . . . . . . . . . . . . . . . . . . .Tri-ShieldCRD . . . . . . . . .Corrosion Resistant DropAPD . . .Amorphous Polypropylene DropV . . . . . . . . . . . . . . . . . . . . . . .NEC CATVR . . . . . . . . . . . . . . . . . . . . . .NEC CATVRFT1 . . . . . . . . . . . . . . . . .CSA Flame TestFT4 . . . . . . . . . . . . . . . . .CSA Flame Test

F2-5967BVM

F5967BVM

F59SSVR

F2-5967BV-CRD

Jacket Aluminum Bonded Dielectric CenterBraided Aluminum ConductorShield Foil Shield

Super Shield (Quad) Construction

Standard Shield Construction

Commscope Drop CablePart Number Matrix

G

Cable & ConnectorsDrop Cable

Drop Cable RG 59

Basic Construction 20 AWG (nom. 0.032" [0.81mm]) copper covered steel cen-ter conductor; gas expanded polyethylene dielectric; innershield aluminum-polypropylene-aluminum laminated tapewith overlap bonded to dielectric; outer shield of 34 AWGbare aluminum braid wire; jacket of black polyvinylchlorideor polyethylene (flooded). Nominal O.D. 0.242" (6.15mm). 20dB minimum SLR at 5-1000 MHz. All cables listed meet NECarticle 820 and have at least a "V" rating.


Description Order No. CommScope Order No. BeldenRG 59 67% Braid Black in a box CSP 202349 F5967BVV-BOX-BLACK BEL 202361 9104U-BLACK

RG 59 67% Braid White in a box CSP 202350 F5967BVV-BOX-WHITE BEL 202362 9104U-WHITE

RG 59 67% Braid Neutral in a box CSP 202351 F5967BVV-BOX-NEUTRAL BEL 202363 9104U-NEUTRAL

RG 59 67% Braid Black on a reel CSP 202352 F5967BVV-REEL-BLACK BEL 202364 9104-REEL-BLACK

Messengered RG 59 67% Braid on a reel CSP 202353 F5967BVM-REEL-BLACK BEL 202365 9105-REEL-BLACK

Underground RG 59 67% Braid on a reel CSP 202354 F5967BEF-REEL-BLACK BEL 202366 9067-REEL-BLACK

RG 59 Quad-Shield Black in a box CSP 202355 F59SSVV-BOX-BLACK N/A

RG 59 Quad-Shield White in a box CSP 202356 F59SSVV-BOX-WHITE N/A

RG 59 Quad-Shield Neutral in a box CSP 202357 F59SSVV-BOX-NEUTRAL N/A

RG 59 Quad-Shield Black on a reel CSP 202358 F59SSVV-REEL-BLACK BEL 202367 1186A-REEL-BLACK

Messengered RG 59 Quad-Shield on a reel CSP 202359 F59SSVM-REEL-BLACK BEL 202368 1188A-REEL-BLACK

Underground RG 59 Quad-Shield on a reel CSP 202360 F59SSEF-REEL-BLACK BEL 202369 1187A-REEL-BLACK

All come in 1000 ft. lengths +-10%





G

Cable & ConnectorsDrop Cable

Drop Cable RG 6

Basic Construction 18 AWG (nom. 0.040" [1.02mm]) copper covered steel centerconductor; gas expanded polyethylene dielectric; inner shieldaluminum-polypropylene-aluminum laminated tape with over-lap bonded to dielectric; outer shield of 34 AWG bare aluminumbraid wire; jacket of black polyvinylchloride or polyethylene(flooded). Nominal O.D. 0.272" (6.91mm). 20 dB minimumSLR at 5-1000 MHz. All cables listed meet NEC article 820 andhave at least a "V" rating.


Description Order No. CommScope Order No. Belden

RG6 60% Braid Black in a box CSP 202370 F660BVV-BOX-BLACK BEL 202382 9116U-BLACK

RG6 60% Braid White in a box CSP 202371 F660BVV-BOX-WHITE BEL 202383 9116U-WHITE

RG6 60% Braid Neutral in a box CSP 202372 F660BVV-BOX-NEUTRAL BEL 202384 9116U-NEUTRAL

RG6 60% Braid Black on a reel CSP 202373 F660BVV-REEL-BLACK BEL 202385 9116-REEL-BLACK

Messengered RG6 60% Braid on a reel CSP 202374 F660BVM-REEL-BLACK BEL 202386 9117-REEL-BLACK

Underground RG6 60% Braid on reel CSP 202375 F660BEF-REEL-BLACK-PE BEL 202387 9066-REEL-BLACK-PE

RG6 Quad-Shield Black in a box CSP 202376 F6SSVV-BOX-BLACK BEL 202388 1189U-BLACK

RG6 Quad-Shield White in a box CSP 202377 F66SSVV-BOX-WHITE BEL 202389 1189U-WHITE

RG6 Quad-Shield Neutral in a box CSP 202378 F66SSVV-BOX-NEUTRAL BEL 202390 1189U-NEUTRAL

RG6 Quad-Shield Black on a reel CSP 202379 F6SSVB-REEL-BLACK BEL 202391 1189A-REEL-BLACK

Messengered RG6 Quad-Shield Black on a reel CSP 202380 F6SSVM-REEL-BLACK BEL 202392 1191A-REEL-BLACK

Underground RG6 Quad-Shield Black on a reel CSP 202381 F6SSEF-REEL-BLACK BEL 202393 1190A-REEL-BLACK

All come in 1000 ft. lengths +-10%



G


Drop Cable RG 7


Ordering Information RG -7

Description Order No. CommScope Order No. Belden

RG7 60% Braid Black on a reel CSP 202394 F760BVV-REEL-BLACK BEL 202400 1844A

Messengered RG7 60% Braid Black on a reel CSP 202395 F760BVM-REEL-BLACK BEL 202401 1845A

Underground RG7 60% Braid Black on a reel CSP 202396 F760BEF-REEL-BLACK BEL 202402 1846A

RG7 Quad-Shield Black on a reel CSP 202397 F7SSVV-REEL-BLACK BEL 202403 1833A

Messengered RG7 Quad-Shield Black on a reel CSP 202398 F7SSVM-REEL-BLACK BEL 202404 1834A

Underground RG7 Quad-Shield Black on a reel CSP 202399 F7SSEF-REEL-BLACK BEL 202405 1835A

Ordering Information RG -11

Description Order No. CommScope Order No. BeldenRG11 60% Braid Black on a reel CSP 202406 F1160BVV-REEL-BLACK BEL 202412 1523A

Messengered RG11 60% Braid Black on a reel CSP 202407 F1160BVM-REEL-BLACK BEL 202413 1523A

Underground RG11 60% Braid Black on a reel CSP 202408 F1160BEF-REEL-BLACK BEL 202414 1525A

RG11 Quad-Shield Black on a reel CSP 202409 F11SSVV-REEL-BLACK BEL 202415 1617A

Messengered RG11 Quad-Shield Black on a reel CSP 202410 F11SSVM-REEL-BLACK BEL 202416 1619A

Underground RG11 Quad-Shield Black on a reel CSP 202411 F11SSEF-REEL-BLACK BEL 202417 1618A

All come in 1000 ft. lengths + - 10%



Drop Cable RG-11



G

Cable & ConnectorsCables

Wireless / DBS Cables 1800 MHz

Basic Construction Direct Broadcast Satellite (DBS) is a method for bringing videoservices to satellite subscribers. Whereas conventional broad-band coax may be tested to only 1 GHz, coaxial DBS cables aresweep tested to 1.8 GHz. They are guaranteed to have mini-mum SRL performance levels of 18 dB to 1.45 GHz and 15 dBbeyond that, out to 1.8 GHz.


Description CommScope # TeleWire # Belden # TeleWire#

RG6 60% Braid Black 5730 CNT 081705 1829A BEL 202447

RG6 60% Braid Dual Black 5786 CNT 133672 1841A BEL 202448

RG6 60% Braid Dual with Ground Wire Black 5788 CNT 296500 1840A BEL 202449

RG6 60% Braid Dual with Flooding Compound Black 5787 CNT 604993 1842A BEL 202450

RG6 60% Braid Dual with Flooding Compound 5789 CNT 201505 1843A BEL 202451and Ground Wire Black


Plenum Cables

Basic Construction Plenums are the enclosed air spaces in office buildings whichare used for supply or return ventilation and can house the elec-trical and communications wiring for the building. Because theair space is unobstructed, plenums represent an area where firecan be spread quickly if combustible materials are present.

Plenum Cable is made of fluoropolymers that propagate flameat a very slow rate and have low smoke generating properties.For these reasons, plenum cables are approved by the NationalFire Protection Agency to be installed without conduit.

Although plenum cables have a higher initial cost than a similarnon-plenum cable, they cost less to install because they do notrequire conduit. They are especially resistant to cracking, abra-sion, chemicals and extreme temperatures. (-40°F to +400°F).


Order Mfg.No. No. DescriptionCNT 200240 2020K RG59 67% Braid

CNT 202459 2275K RG6 60% Braid

CNT 202458 2227K RG6 Quad shield

CNT 296476 2285K RG11 60% Braid


G

Cable & ConnectorsHeadend Cable

RG59 (S59 HEC) Basic Construction:22 AWG (nom. 0.0226" (0.58 mm)) silver plated copper coveredsteel center conductor; solid natural polyethylene dielectric;inner shield aluminum-polypropylene-aluminum laminatedbonded overlap; outer shields of 34 AWG tinned copper braid;jacket flame retardant black polyvinylchloride. Nom. O.D.0.265" (6.73 mm). 61 lbs. per 1,000 feet.

Headend CableBELDEN

RG59 (9167) Basic Construction20 AWG (nom. 0.032" [0.81mm]) silver plated copper coveredsteel center conductor; gas injected foam polyethylene dielec-tric; shield Duobond II plus 95% aluminum braid plus aluminumfoil with shorting fold; jacket black polyvinylchloride. Nom. O.D.0.242" (6.15mm). 29.35 lbs. per 1,000 feet.

Headend CableCOMM/SCOPE


Order Mfg.No. No. DescriptionBEL 202452 9167 RG 59

BEL 294040 9168 RG 6



RG6 (9168) Basic Construction18 AWG (nom. 0.040" [1.02mm]) silver plated copper coveredsteel center conductor; gas injected foam polyethylene dielec-tric; shield Duobond II plus 95% aluminum braid plus aluminumfoil with shorting fold; jacket black polyvinylchloride. Nom. O.D.0.275" (6.99mm). 31 lbs. per 1,000 feet.

RG59 (F59 HEC-2) Basic Construction:22 AWG (nom. 0.0226" (0.58 mm)) silver plated copper coveredsteel center conductor; gas expanded polyethylene dielectric;inner shield aluminum-polypropylene-aluminum laminatedbonded overlap; outer shields of 34 AWG tinned copper braid;jacket flame retardant black polyvinylchloride. Nom. O.D.0.265" (6.73 mm). 61 lbs. per 1,000 feet.

RG59 (F59 HEC / 3-22) Basic Construction:22 AWG (nom. 0.032" [0.81 mm]) silver plated copper coveredsteel center conductor; gas expanded polyethylene dielectric;inner shield aluminum-polypropylene-aluminum laminated tapewith overlap bonded to dielectric; 34 AWG aluminum braid; alu-minum-polypropylene-aluminum non-bonded tape; 34 AWGaluminum braid; jacket flame retardant black polyvinylchloridemeeting NEC Article 820, CATV category and 725 Class 2Circuit Ratings. Nom. O.D. 0.270" (6.86 mm). Audio: three pair22 AWG bare copper, polyethylene insulation; 24 AWG tin/cop-per drain and polyester rip cord with aluminum shld on eachpair; dual construction. 59 lbs. per 1,000 feet.

RG214 (7714) Basic Construction:Center conductor: 13 AWG, 7/.0296 SC wire type, 1.73 nom.DCR Ohms/1000'; dielectric: PE, .285" nom. O.D., shield con-struction: 2-95% SC, .7 nom. DCR/1000'; jacket: NCPVC,.425" nom. O.D.; nom. cap.: 30.8 pt/ft.; velocity of propagation:66%; impedance: 50 Ohms. 500' reels 159 lbs per 1,000 feet.


Order Mfg.No. No. DescriptionCSP 202453 S59 HEC RG 59

CSP 135672 F59 HEC-2 RG 59

CSP 140798 F59 HEC/3-22 RG 59 single w/ three22 AWG twisted pair

CNT 201454 7714 RG 214

RG 214



G

Cable & ConnectorsAudio / Telephone Cable &Headend Connectors


Order Mfg.No. No. DescriptionPIC 101498 NMA234 RG-213

GIL 072913 GN-214AHS/480 RG-214

BHG 137498 HCT-480 for RG 213 connectors

BHG 043364 HCT-211 for RG 214 connectors


Order Mfg.No. No. Description Qty.BEL 600232 8760-U-500 18 gauge stranded pair 500' box

chrome jacket

BEL 202460 8762-U-500 20 gauge stranded pair 500' boxchrome jacket

BEL 600231 8451-U-500-8 22 gauge stranded pair 500' boxgrey jacket

BEL 202461 8451-1000 22 gauge stranded pair 1000' reelblack jacket

Basic Construction: Tinned copper, polyethylene insulated, twisted pair. Beldfoil®aluminum-polyester shield, stranded tinned copper drain wire.Chrome PVC jacket. Color code: black, clear.

DescriptionRound 4 conductor in 1,000 foot lengths.

Order Mfg. ConductorNo. No. Size Cont. TypeSWI 200904 24-4/C beige 24 box beige

SWI 200907 24-4/C gray 24 box gray

SWI 200908 22-4/C beige 22 box beige

SWI 200906 22-4/C gray 22 box gray


RG-213 Male 50 Ohm Ntype Connector

RG-214 Male 50 Ohm Ntype Connector

Crimp Tool for RG 213 & RG214 N Type Connectors

RG-213, RG-214 Connectors

Telephone Station WireJUST DROP

Shielded Twisted Pair CableBELDEN



G

Cable & ConnectorsConnectors

Aluminum Connector Types

Feed-Thru (‘VSF’)A device that seizes only the outer conductor of the coaxialcable. The cable center conductor extends through the con-nector and is retained within the equipment housing.

Pin Type (‘Stinger’)A connector that seizes both the outer and center conductor.This device has an additional feature not found in the feed-thrutype consisting of a solid brass pin which seizes and retains thecable center conductor. The pin then extends through the bodyand is retained within the equipment housing.

Splice This connector is used to join together two cables. The featuresof seizing both the outer and center conductors (as in the pin-type) are found in this device.

“F” FemaleThis connector is used when an “F” female port is required atthe end of the cable. It has identical features as the pin-typeand splice in that it seizes both the center and outer conductorof the coaxial cable.

“F” MaleThis connector is used when it is necessary to have an “F”male connection at the end of the cable. It has the same fea-tures as the pin-type, splice and “F” female in that both centerand outer conductors of the cable are seized.

ExtensionThis connector is used when sufficient cable is not available forinstallation. It has a pin which seizes and retains the cable cen-ter conductor. The pin then extends through the body and isretained with the equipment housing.

Cable TerminatorThis connector is used in a cable system where it becomesnecessary to terminate both RF signal and 60 Hz AC power. Itcontains the center and outer conductor seizing features as inthe pin-type, splice, "F" female and "F" male connectors.



G

Cable & ConnectorsGilbert Connector Quick Reference

Gilbert Aluminum Connectors with Integral Sleeves

Feed Thru ('VSF)Order Mfg. Order Mfg.No. No. No. No.GIL 023516 GRS412BA01 GIL 049528 GRS500BDU03

GIL 049527 GRS412BDU01 GIL 095021 GRS500BMC2

GIL 031927 GRS412BSDU01 GIL 037614 GRS500BSDU03

GIL 023517 GRS500BA01 GIL 112733 GRS540BSQR

GIL 099939 GRS500BDU01 GIL 049529 GRS750BDU01

GIL 072632 GRS500BDU02 GIL 099966 GRS625BDU02

Pin Type ('Stinger')Order Mfg. Order Mfg. Order Mfg.No. No. No. No. No. No.

GIL 023518 GRS412CHA01 GIL 094029 GRS500CHMC2T GIL 039952 GRS750CHFD04

GIL 061694 GRS412CHA01T GIL 085313 GRS500CHQR GIL 039953 GRS750CHFD04T

GIL 044455 GRS412CHA07 GIL 059442 GRS540CHQR GIL 073499 GRS750CHMC2

GIL 044459 GRS412CHA07T GIL 112574 GRS540CHQRT GIL 072161 GRS750CHMC2T

GIL 022628 GRS412CHDU01 GIL 041944 GRS625CHDU02 GIL 059452 GRS860CHQR

GIL 043528 GRS412CHDU01T GIL 050245 GRS625CHDU02T GIL 112352 GRS860CHQRT

GIL 112650 GRS440CHMC GIL 109233 GRS650CHMC2 GIL 042758 GRS875CHA02

GIL 023519 GRS500CHA01 GIL 072155 GRS650CHMC2T GIL 042759 GRS875CHDU02

GIL 061695 GRS500CHA01T GIL 144117 GRS715CHQR GIL 050246 GRS875CHDU02T

GIL 052449 GRS500CHA05 GIL 144441 GRS715CHQRT GIL 150191 GRS1000CHA01

GIL 087210 GRS500CHCX GIL 023661 GRS750CHA01 GIL 037931 GRS1000CHDU01

GIL 023660 GRS500CHDU01 GIL 057112 GRS750CHA01T GIL 056289 GRS1000CHDU01T

GIL 096071 GRS500CHDU01T GIL 146507 GRS750CHA02 GIL 094302 GRS1000CHMC2T

GIL 031876 GRS500CHDU02 GIL 031659 GRS750CHDU01 GIL 112785 GRS1125CHQRT

GIL 036247 GRS500CHDU03 GIL 048086 GRS750CHDO01T GIL 114411 GRS13.0CHDU01

GIL 042515 GRS500CHDU03T GIL 042499 GRS750CHDU03 GIL 072152 GRS16.5CHDU01T

GIL 089589 GRS500CHMC2 GIL 112356 GRS750CHDO03T

ExtensionOrder Mfg. Order Mfg.No. No. No. No.

GIL 057115 GRS412EXTA01T GIL 101444 GRS625EXTDU02T

GIL 042210 GRS412EXTDU01T GIL 057117 GRS750EXTA01T

GIL 057116 GRS500EXTA01T GIL 101114 GRS750EXTDU01T

GIL 099964 GRS500EXTDU01 GIL 099968 GRS750EXTDU03

GIL 101350 GRS500EXTDU03T GIL 112782 GRS860EXTQRT

GIL 048662 GRS500EXT9A01 GIL 146475 GRS875EXTDU02T



G

Cable & ConnectorsGilbert Connector Quick Reference

Gilbert Aluminum Connectors with Integral Sleeves continued

Order Mfg.No. No.GIL 040374 GRS500TRA01

GIL 043481 GRS500TRDU03

GIL 077191 GRS625TRDU02

SpliceOrder Mfg. Order Mfg.No. No. No. No.

GIL 023520 GRS412SPA01 GIL 072160 GRS650SPMC2

GIL 023525 GRS412SPA01DU03 GIL 144840 GRS715SPQR

GIL 023524 GRS412SPA01DU01 GIL 023665 GRS750SPA01

GIL 044456 GRS412SPA07 GIL 031898 GRS750SPA01DU01

GIL 023663 GRS412SPDU01 GIL 037729 GRS750SPDU01

GIL 023521 GRS500SPA01 GIL 076394 GRS750SPDU03

GIL 037942 GRS500SPA01DU03 GIL 033730 GRS750SPFD04

GIL 031877 GRS500SPDU01 GIL 072158 GRS750SPMC2

GIL 023664 GRS500SPDU02 GIL 059453 GRS860SPQR

GIL 036248 GRS500SPDU03 GIL 050242 GRS875SPDU02

GIL 096024 GRS500SPMC2 GIL 150188 GRS1000SPA01

GIL 077852 GRS500SPQR GIL 037932 GRS1000SPDU01

GIL 059445 GRS540SPQR GIL 099932 GRS1000SPMC2

GIL 050243 GRS625SPDU02 GIL 091962 GRS1125SPQR

"F" Male

"F" Female

Cable Terminator

Order Mfg.No. No.GIL 037933 GRS412AFMA01

GIL 037934 GRS412AFMDU01

GIL 037935 GRS500AFMA01

GIL 037937 GRS500AFMDU03

Order Mfg. Order Mfg.No. No. No. No.

GIL 024024 GRS412BAFFA01 GIL 004657 GRS625BAFFDU02

GIL 031928 GRS412BAFFDU01 GIL 031895 GRS750BAFFA01

GIL 024023 GRS500BAFFA01 GIL 035011 GRS750BAFFDU01

GIL 035372 GRS500BAFFDU01 GIL 109242 GRS750BAFFMC2

GIL 036249 GRS500BAFFDU03 GIL 059449 GRS860BAFFQR

GIL 109191 GRS500BAFFMC2 GIL 099996 GRS875BAFFDU02

GIL 112688 GRS540BAFFQR GIL 094299 GRS1000BAFFDU01



G

Cable & ConnectorsLRC Connectors Quick Reference

Product SpecificationsLRC

Features• Structural return loss meets or exceeds 30 dB up to

1 GHz on entry and splice connectors and most adapters• Radiation sleeves provide excellent RF integrity and

shield effectiveness• No-twist center conductor seizing mechanism eliminates

radial stress• Positive stop feature eliminates guesswork and assures

proper tightening of the connector to cable interface• O-ring sealed for maximum environmental protection• Center conductor cutting guide assures accurate center

conductor length• One wrench size required for each connector• Connector pull force meets or exceeds yield strength of the cable• Manufactured from 6262 aluminum alloy and iridite coated

for superior corrosion resistance.• Threads are lubricated to prevent galling during installation• Terminals made from brass are silver plated for excellent

RF conductivity• Two-inch pin length is standard to accommodate

installation requirements

Feed Through ("VSF")

Order Mfg. Order Mfg.No. No. No. No.

LRC 096280 EMI412K3 LRC 071707 EMI500P3

LRC 096273 EMI500K LRC 112894 EMI540QR

LRC 081907 EMI500K3 LRC 081916 EMI625K3

LRC 109215 EMI500MC2 LRC 112348 EMI750W3

• Selected plastic materials are used to provide dependableelectrical and mechanical integrity at temperatures from -40°F to +170°F

• Part number is permanently stamped on connector foreasy identification

DescriptionThe K series is a patented 2-piece design which requires thetightening of only one nut to seize both the center conductorand aluminum sheath of the cable. This design requires lesstime to install than a 3-piece connector, making installation eas-ier and faster.

The W series is the original 3-piece connector design whichhas been manufactured for over 20 years. The three-piececonnector design seizes the center conductor and aluminumsheath of the cable, independent of each other. This is done bytightening two nuts, allowing for full view of the center conduc-tor entrance into the seizing mechanism. The 30 dB minimumreturn loss has been extended to 1 GHz on pin and splice con-nectors to accommodate future channel expansion.

Pin Type (‘Stinger’)

Order Mfg. Order Mfg.No. No. No. No.LRC 096278 EI412K LRC 081914 EI625K3

LRC 096264 EI412K3 LRC 109227 EI650MC2

LRC 041312 EFI500W3 LRC 041313 EFI750W3

LRC 040698 EI500B LRC 152637 EI715K3

LRC 096214 EI500K LRC 081919 EI750K3

LRC 081906 EI500K3 LRC 109269 EI750MC2

LRC 109214 EI500MC2 LRC 067372 EI860QR

LRC 112510 EI540QR LRC 049837 EI875B3

LRC 149154 EI565TX LRC 102131 EI875K3

LRC 055476 EI625B3 LRC 152635 EI1000MC2

Aluminum Connectors with Integral Sleeves



G

Cable & ConnectorsLRC Connector Quick Reference

Order Mfg. Order Mfg.No. No. No. No.LRC 112339 EFI412PWLB LRC 081909 EI500K3LB

LRC 040688 EI412B3LB LRC 109197 EI500QRLB

LRC 096265 EI412K3LB LRC 149155 EI565TXLB

LRC 040710 EI500BLB LRC 081922 EI750K3LB

LRC 096215 EI500KLB

Aluminum Connectors with Integral Sleeves continued

Splice

Order Mfg. Order Mfg.No. No. No. No.LRC 041314 SFI750W3 LRC 152636 SI715K3

LRC 096271 SI412K LRC 040726 SI750B

LRC 096266 SI412K3 LRC 040727 SI750B3

LRC 040700 SI500B LRC 081920 SI750K3

LRC 096213 SI500K LRC 109268 SI750MC2

LRC 081908 SI500K3 LRC 112353 SI860QR

LRC 109213 SI500MC2 LRC 051716 SI875B3

LRC 112509 SI540QR LRC 096269 SI875K3

LRC 096267 SI625K3

Extension

"F" Female

Order Mfg.No. No.

LRC 112829 AI412FFK3

LRC 112495 AI500FFK


LRC 112475 AI500FFW3




G


Coaxial ConnectorsCABLE-CON

DescriptionThese products have been designed for coaxial cables with acharacteristic impedance of 75 ohms. Connectors are availablefor most types of commonly used cables.

All connectors are designed and constructed of the finest mate-rials to exacting specifications to insure a mechanically andelectrically superior interface. Bodies and nuts are made from6262-T6 aluminum treated with a chromic acid conversion coatto prevent corrosion. All pins are made of brass and plated with

Hardline Gold Series FeaturesInstallation Friendly

• Designed with field installation in mind. Easy assemblyhelps to eliminate installation errors.

• One wrench size per connector• Trim guides in connector body to insure exact center

conductor length.• Metal to metal positive stop eliminates over tightening

of connector.• Slim body design allows for easier installation in confined

spaces such as pedestals. Smaller wrenches required foreasier and lighter handling.

• Better heat shrink application over connectors and connection into ports.

• Uses standard coring and stripping tools. No need forspecial tools.

Three Piece Design• Allows for independent confirmation of a secure installa-

tion from the seizing of the cable’s center conductor to thegripping of the cable itself.

• Visible confirmation of the center conductor entry into theconnector body.

• True Non-rotational design built into body to keep cablefrom turning.

CATV Connectors with True Cable Non-Rotation Feature*AMPHENOL

bright acid tin. Radiation sleeves are either stainless steel or tinplated brass.

Connectors are sealed with o-rings made of ethylene propy-lene to prevent moisture ingress. Ethylene propylene insureslong o-ring life even in high ozone atmospheres.

Cabel con’s connectors meet stringent quality standards andare tested over a wide range of environmental conditions.

Quality Materials• High quality corrosion resistant aluminum alloy parts

(6262 or equivalent).• High quality 360 brass parts.• E/P - Ethylene/Propylene o-rings for superior sealing.

O-zone, ultraviolet and salt spray resistant. Tested andguaranteed in all environments.

• Lubricant on all threads for smooth anti-locking operation.• Pressed plastic insulator seals unit from condensation and

moisture migration.

Top Performance• Meets or exceeds industry standards for RFI leakage

and return loss.• All connectors are swept from .3 MHz to 1 GHz.• Environmental testing includes pressure and salt spray tests.

Cost Effectiveness• Slim design means less material which keeps product costs low.• Slim design means a smaller heat shrink which saves

dollars on associated material construction costs.• 2" Pin standard at no extra charge.

*Patent applied for

Commitment to QualityProducts are manufactured at the Amphenol RF/MicrowaveOperations, Danbury, CT facility which is ISO 9001 SystemCertified.

Amphenol CATV Connectors is dedicated to provide a com-plete line of quality products including hardline and drop con-nectors, adaptors, terminators and cable preparation tools.

Amphenol CATV Connector products are designed and man-ufactured to meet our established requirements and theexpectations of our customers.

We believe that our connector products will enhance the qual-ity of your system, while reducing installation time and provid-ing years of maintenance free service.

Quality SystemISO 9001Certified

Hardline ConnectorsAmphenol Gold Series Hardline connectors are the best perform-ing connectors available today with 40 dB return loss up to 1 GHz.The connectors are designed to meet all SCTE, Bellcore and otherkey industry performance and environmental specifications. Theyincorporate a true non-rotational three piece design to prevent thecable from turning during installation. Other installation friendly fea-tures include slim body design for confined spaces, requirement ofone wrench size per connector, and metal to metal positive stop toeliminate over and under tightening of the connector.



G


Aluminum Connectors for .412 Cable

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Cerro Cerrofoam GXX 4412-CCComm/Scope Parameter III P3-75-412-CACCS Cable GID-3 46200Times Lumifoam III JT-4412

A. Feed-Thru B. Pin Type C. Splice D. "F" Female

E. "F" Male F. Extension G. Cable Terminator

Order Gilbert Order LRC Order Cabel ConFig. No. No. No. No. No. No.A GIL 049527 GRS412BDU01 LRC 096280 EMI412K3 — —

A† GIL 031927 GRS412BSDU01 — — — —

B GIL 022628 GRS412CHDU01 — — — —

B* GIL 043528 GRS412CHDU01T LRC 096264 EI412K3 CBC 604550 PI-412-CH-3

C GIL 023663 GRS412SPDU01 LRC 096266 SI412K3 CBC 604565 PI-412-SP-3

D GIL 031928 GRS412BAFFDU01 LRC 112829 AI412FFK3 — —

E GIL 037934 GRS412AFMDU01 — — — —

F GIL 042210 GRS412EXTDU01T LRC 096265 EI412K3LB — —

G GIL 044458 GRS412TRDU01 — — — —

Order GilbertFig. No. No.A GIL 049527 GRS412BDU01

A† GIL 031927 GRS412BSDU01

B GIL 022628 GRS412CHDU01

B* GIL 043528 GRS412CHDU01T

C GIL 023663 GRS412SPDU01

D GIL 031928 GRS412BAFFDU01

E GIL 037934 GRS412AFMDU01

F GIL 042210 GRS412EXTDU01T

G GIL 044458 GRS412TRDU01

All Gilbert and Amphenol are 3 pieceAll Gilbert extension connectors have long pinsAll LRC and Cable Con are 2 PieceAll LRC, Amphenol and Cable Con Connectors come standard with long pin

The Order Numbers Below Fit the Following CablesGeneral Fused Disc III Cables

* Longer Pin Version † Contains seal

Illustrations shown above are pictured as a reference only.Actual product may vary from these illustrations.Artwork ©1996 Gilbert Engineering Co., Inc.



G


Aluminum Connectors for .412 Cable continued

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Parameter II P-2-75-412-CA

Order Gilbert Order LRCFig. No. No. No. No.A GIL 049527 GRS412BDU01 LRC 096280 EMI412K3

A† GIL 031927 GRS412BSDU01 — —

B GIL 022628 GRS412CHDU01 — —

B* GIL 043528 GRS412CHDU01T LRC 096264 EI412K3

C GIL 023663 GRS412SPDU01 LRC 096266 SI412K3

D GIL 031928 GRS412BAFFDU01 LRC 112829 AI412FFK3

E GIL 037934 GRS412AFMDU01 — —

F GIL 042210 GRS412EXTDU01T LRC 096265 EI412K3LB

G GIL 044458 GRS412TRDU01 — —

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Cerro Cerrofoam 2412-CCComm/Scope Cell-O-Air XD-75-412-CATimes Dynaplus JT-2412

Order Gilbert Order LRCFig. No. No. No. No.A GIL 049527 GRS412BDU01 LRC 096280 EMI412K3

A† GIL 031927 GRS412BSDU01 — —

B GIL 022628 GRS412CHDU01 — —

B* GIL 043528 GRS412CHDU01T LRC 096264 EI412K3

C GIL 023663 GRS412SPDU01 LRC 096266 SI412K3

D GIL 031928 GRS412BAFFDU01 LRC 112829 AI412FFK3

E GIL 037934 GRS412AFMDU01 — —

F GIL 042210 GRS412EXTDU01T LRC 096265 EI412K3LB

G GIL 044458 GRS412TRDU01 — —

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.General Fused Disc .412










The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.CCS Cable GID 1 44200CCS Cable Chemafoam 42200Cerro Cerrofoam GX 3412-CCComm/Scope Alumagard AL-75-412-CAComm/Scope Parameter I P1-75-412-CATimes Alumifoam JT-1412Times Alumifoam II 22-3412Scientific-Atlanta 20 22-412

Order Gilbert Order LRCFig. No. No. No. No.A GIL 023516 GRS412BA01 — —

A† GIL 112893 GRS412BSA01 — —

B GIL 023518 GRS412CHA01 — —

B* GIL 061694 GRS412CHA01T LRC 096278 EI412K

C GIL 023520 GRS412SPA01 LRC 096271 SI412K

D GIL 024024 GRS412BAFFA01 — —

E GIL 037933 GRS412AFMA01 — —

F GIL 057115 GRS412EXTA01T — —


All Gilbert and Amphenol are 3 pieceAll Gilbert extension connectors have long pinsAll LRC and Cable Con are 2 PieceAll LRC, Amphenol and Cable Con Connectors come standard withlong pin



G



The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Cerro Cerrofoam GXX 4500-CC

Comm/Scope Parameter III P3-75-500-CA

CCS Cable GID-3 56200



Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No. No.A GIL 049528 GRS500BDU03 LRC 081907 EMI500K3 — — — —

A† GIL 037614 GRS500BSDU03 — — — — — —

B GIL 036247 GRS500CHDU03 — — — — — —

B* GIL 042515 GRS500CHDU03T LRC 081906 EI500K3 APL 201513 ACC500CHP3 CBC 200361 PI-500-CH-3

C GIL 036248 GRS500SPDU03 LRC 081908 SI500K3 APL 201525 ACC500SPP3 CBC 200366 PI-500-SP-3

D GIL 036249 GRS500BAFFDU03 LRC 081910 AI500FFK3 APL 201537 ACC500BAFFP3 — —

E GIL 037937 GRS500AFMDU03 LRC 109195 AI500FMK3 — — — —

F GIL 048661 GRS500EXTDU03T LRC 081909 EI500K3LB — — — —

G GIL 043481 GRS500TRDU03 — — — — — —










The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.General Fused Disc MIII 6977797












G


Aluminum Connectors for .500 Cable continued








The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Cerro Cerrofoam GX 3300-CCComm/Scope Parameter I P-1-75-500-CAComm/Scope Alumagard AL-75-500-CACCS Cable Chema-Foam 52200CCS Cable GID I 54200Times Alumifoam JT-1500Times Alumifoam II JT-3500Scientific Atlanta 20 22-500Scientific Atlanta Polyethylene 2-500

Order Gilbert Order LRCFig. No. No. No. No.A GIL 023517 GRS500BA01 LRC 096273 EMI500K

B GIL 023519 GRS500CHA01 — —

B* GIL 061695 GRS500CHA01T LRC 096214 EI500K

C GIL 023521 GRS500SPA01 LRC 096213 S1500K

D GIL 024023 GRS500BAFFA01 LRC 112495 AI500FFK

E GIL 037935 GRS500AFMA01 — —

F GIL 057116 GRS500EXTA01T LRC 096215 EI500KLB

G GIL 040374 GRS500TRA01 — —

The Order Below Numbers Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Quantum Reach QR-500-JCA

Order GilbertFig. No. No.B GIL 085313 GRS500CHQR

B* GIL 112563 GRS500CHQRT

C GIL 077852 GRS500SPQR

D GIL 024026 GRS500BAFFQR


The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Quantum Reach QR-500-JCA

Order GilbertFig. No. No.B GIL 085313 GRS500CHQR

B* GIL 112563 GRS500CHQRT

C GIL 077852 GRS500SPQR

D GIL 024026 GRS500BAFFQR

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Trilogy MC2 2101012

Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No. No.A GIL 095021 GRS500BMC2 LRC 109215 EMI500MC2 — — — —

B GIL 089589 GRS500CHMC2 — — — — — —

B* GIL 094029 GRS500CHMC2T LRC 109214 EI500MC2 APL 201517 ACC500CHMC CBC 604557 PI-500-CH-4

C GIL 096024 GRS500SPMC2 LRC 109213 SI500MC2 APL 201529 ACC500SPMC CBC 604572 PI-500-SP-4

D GIL 109191 GRS500BAFFMC2 — — APL 201514 ACC500BAFFMC CBC 604594 PI-500-BAFF-04



G


Aluminum Connectors for .540 (QR) Cable

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Quantum Reach QR-540JCA


Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No. No.A — — LRC 112894 EMI540QR — — — —

A† GIL 112733 GRS540BSQR — — — — — —

B GIL 059442 GRS540CHQR — — — — — —

B* GIL 112574 GRS540CHQRT LRC 112510 EI540QR APL 201522 ACC540CHQR CBC 200364 PI-540-CH-5

C GIL 059445 GRS540SPQR — — APL 201534 ACC540SPQR CBC 200367 PI-540-SP-5

D GIL 112688 GRS540BAFFQR — — APL 201546 ACC540BAFFQR CBC 604597 PI-540-BAFF-5




Aluminum Connectors for .565 (TX) Cable

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Times Fiber TX10 Semiflex Cable TX10565J


Order Gilbert Order LRC Order AmphenolFig. No. No. No. No. No. No.

B GIL 059442 GRS540CHQR LRC 149154 EI565TX APL 201519 ACC565CHTX

C GIL 059445 GRS540SPQR LRC 149157 SI565TX APL 201531 ACC565SPTX

D — — — — APL 201543 ACC565BAFFTX




G



The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Parameter III P3-75-625-CACCS Cable 66200Scientific Atlanta 30 32-625Times Lumifoam III JT-4625Times T4 Plus 22600Trilogy 3111011



Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No. No.A GIL 099966 GRS625BDU02 LRC 081916 EMI625K3 — — — —

B GIL 041944 GRS625CHDU02 — — — — — —



D GIL 004657 GRS625BAFFDU02 — — APL 201538 ACC625BAFFP3 — —

F GIL 101444 GRS625EXTDU02T — EI625K3LB — — — —

G GIL 077191 GRS625TRDU02 — — — — — —


All Gilbert and Amphenol are 3 pieceAll Gilbert extension connectors have long pinsAll LRC and Cable Con are 2 PieceAll LRC, Amphenol and Cable Con Connectors come standard withlong pin




G


Aluminum Connectors for .650 (MC2) Cable



Order Gilbert Order LRCFig. No. No. No. No.B GIL 109233 GRS650CHMC2 LRC 109227 EI650MC2

B* GIL 072155 GRS650CHMC2T LRC 109227 EI650MC2

C GIL 072160 GRS650SPMC2 LRC 109226 SI650MC2





The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Times Fiber TX10 Semiflex Cable TX10700J


Order Amphenol Order LRCFig. No. No. No. No.B APL 201520 ACC700CHTX LRC 201440 EI700TX

C APL 201532 ACC700SPTX — —

D APL 201544 ACC700BAFFTX — —




G





Order Gilbert Order LRC Order AmphenolFig. No. No. No. No. No. No.B GIL 144117 GRS715CHQR — — — —

B* GIL 144441 GRS715CHQRT LRC 152637 EI715QR APL 201523 ACC715CHQR

C GIL 144840 GRS715SPQR LRC 152636 SI715QR APL 201535 ACC715SPQR

D — — — — APL 201547 ACC715BAFFQR






G



The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Cerro Cerrofoam-GXX 4720-CCComm/Scope Parameter III P3-75-750-CACCS Cable GID III 76200Scientific Atlanta 30 32-750Times Lumifoam III JT-4750Times T4 Plus 22700



Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No.No.A GIL 049529 GRS750BDU01 — — — — — —

B GIL 031659 GRS750CHDU01 — — — — — —



D GIL 035011 GRS750BAFFDU01 LRC 081923 AI750FFK3 APL 201539 ACC750BAFFP3 — —

E GIL 109241 GRS750AFMDU01 — — — — — —

F GIL 057118 GRS750EXTDU01T LRC 081922 EI750K3LB — — — —

G GIL 044522 GRS750TRDU01 — — — — — —










The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.General Fused Disc MIII 6977615





G












The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Cerro Cerrofoam GX 3750-CCComm/Scope Alumagard AL-75-750-CAComm/Scope Parameter I P1-75-750-CACCS Cable Chemafoam 72200CCS Cable GID I 74200Times Alumifoam JT-1750Times Alumifoam II JY-3750

Order Gilbert Order LCRFig. No. No. No. No.B GIL 023661 GRS750CHA01 — —

B* GIL 057112 GRS750CHA01T — —

C GIL 023665 GRS750-SPA01 LRC 096211 SI750K

D GIL 031895 GRS750BAFFA01 — —

F* GIL 057117 GRS750EXTA01T LRC 096279 EI750KLB


Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No. No.B GIL 073499 GRS750CHMC2 LRC 109269 EI750MC2 — — — —

B* GIL 072161 GRS750CHMC2T LRC 109269 EI750MC2 APL 201518 ACC750CHMC CBC 604559 PI-750-CH-04

C GIL 072158 GRS750SPMC2 LRC 109268 SI750MC2 APL 201530 ACC750SPMC CBC 604574 PI-750SP-04

D GIL 109242 GRS750BAFFMC2 LRC 109267 AI750FFMC2 APL 201542 ACC750BAFFMC CBC 604595 PI-750-BAFF-04


Order GilbertFig. No. No.B GIL 039952 GRS750CHFD04

B* GIL 039953 GRS750CHFD04T

C GIL 033730 GRS750SPFD04



G



Aluminum Connectors for .840 (TX) Cable

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Times Fiber, 840TX TX10840J


Order Gilbert Order LRC Order AmphenolFig. No. No. No. No. No. No.B GIL 296189 GRS840CHTX — — APL 201521 ACC840CHTX

C GIL 291365 GRS840SPTX LRC 292886 SI840T APL 201533 ACC840SPTX

D — — — — APL 201545 ACC840BAFFTX

* Longer Pin Version


Aluminum Connectors for .860 (QR) Cable



Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No. No.B GIL 059452 GRS860CHQR — — — — — —

B* GIL 112352 GRS860CHQRT LRC 067372 EI860QR APL 201524 ACC860CHQR CBC 200365 PI-860-CH-5

C GIL 059453 GRS860SPQR LRC 112353 SI860QR APL 201536 ACC860SPQR CBC 200370 PI-860-SP-5

D GIL 059449 GRS860BAFFQR — — APL 201548 ACC860BAFFQR — —

F GIL 112782 GRS860EXTQRT — — — — — —





G



The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Parameter III P3-75-875-CACCS Cable 86200Scientific Atlanta 3032-875Times Lumifoam III JT-4875Times T4 Plus 22800



Order Gilbert Order LRC Order Amphenol Order CableConFig. No. No. No. No. No. No. No. No.B GIL 042759 GRS875CHDU02 — — — — — —



D GIL 099996 GRS875BAFFDU02 — — APL 201540 ACC875BAFFP3 — —

F GIL 100786 GRS875EXTDU02T — — — — — —



Aluminum Connectors for 1.000 Cable

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Parameter III P3-75-1000-CA

Times Lumifoam III JT-41000

Times T4 Plus 22900

Trilogy/Capscan 4 6111011

Order Gilbert Order Amphenol Order Cabel ConFig. No. No. No. No. No. No.B GIL 037931 GRS1000CHDU01 — — — —

B* GIL 056289 GRS1000CHDU01T APL 202440 ACC-1000CHT10 CBC 604555PI-1000-CH-3

C GIL 037932 GRS1000SPDU01 APL 202439 ACC-1000SPT10 CBC 604570PI-1000-SP-3

D GIL 094299 GRS1000BAFFDU01 — — — —




G


Aluminum Connectors for 1.000 (MC2) Cable



Order Gilbert Order LRC Order Amphenol Order Cabel ConFig. No. No. No. No. No. No. No. No.B* GIL 094302 GRS1000CHMC2T LRC 152635 EI1000MC2 APL 202435 ACC-1000CHMC CBC 604560 PI-1000-CH-04

C GIL 099932 GRS1000SPMC2 LRC 152634 SI1000MC2 APL 202436 ACC-1000SPMC CBC 604575 PI-1000-SP-04

D — — — — — — CBC 604596 PI-1000-BAFF-04


Aluminum Connectors for 1.125 (QR) Cable

The Order Numbers Below Fit the Following CablesCable Mfg./Type Mfg. Part No.Comm/Scope Quantum Reach QR-1125-JCA


Order Gilbert Order AmphenolFig. No. No. No. No.B GIL 091961 GRS1125CHQR — —

B* GIL 112785 GRS1125CHQRT APL 202438 ACC-1125-CH-QR

C GIL 091962 GRS1125SPQR APL 202937 ACC-1125-SP-QR


All Gilbert and Amphenol are 3 pieceAll Gilbert extension connectors have long pinsAll LRC and Cable Con are 2 PieceAll LRC, Amphenol and Cable Con Connectors come standard with long pin* Longer Pin Version



G

Cable & ConnectorsAdapters

Adapter-Right Angle to Equipment

Description90 degree coaxial connector designed especially for pedestaltype installations where space restrictions require right angleconnections between coaxial cables.

Ordering Information - Gilbert

Order Mfg.No. No. DescriptionGIL 022320 GP90 no extension

GIL 043063 GP90T no extension, long pin

GIL 072922 GP90-3.0 3" extension

GIL 057345 GP90-3.0T long pin, 3" extension

GIL 057122 GP90-4.5 4.5" extension

GIL 058741 GP90-4.5T long pin, 4.5" extension

Ordering Information - LRC

Order Mfg.No. No. DescriptionLRC 040738 EU90 no extension

LRC 040739 EU90-3 3" extension

LRC 040740 EU90-4.5 4.5" extension

Ordering Information - Amphenol

Order Mfg.No. No. DescriptionAPL 201549 ACC-90 No extension

APL 201550 ACC-901.5 Ext 1-1/2" extension

APL 201551 ACC-903 Ext 3" extension

APL 201552 ACC-904.5 Ext 4.5" extension

APL 201553 ACC-906 Ext 6"extension

Ordering Information - Cabel Con

Order Mfg.No. No. DescriptionCBC 200358 L-90 No extension

CBC 200359 L-90-W/1.5 1-1/2" extension

Adapter-Right Angle Connector to Equipment

DescriptionSame as above except body need not be rotated during installation.


Order Mfg.No. No. DescriptionGIL 076286 GP90S no extension

GIL 094296 GP90ST no extension, long pin



G


Adapter-180° Connector to Equipment

DescriptionProvides connection between amplifier and cable connector in restricted space.

DescriptionHousing to housing coupling connector, eliminates the need forcoaxial jumpers and permits cascadability of taps, etc.

Male Splice Adapter Rotational


Order Mfg.No. No. DescriptionGIL 023522 GPPA ext. length 5.18"

GIL 050244 GPPAT ext. length 5.18", long pin

GIL 057121 GPPA-3.0 ext. length 3.0"

GIL 057401 GPPA-3.0T ext. length 3.0", long pin

GIL 057120 GPPA-4.5 ext. length 4.5"

GIL 058742 GPPA-4.5T ext. length 4.5", long pin


Order Mfg.No. No. DescriptionLRC 040738 EU90 (2 ea.) ext. length 5.18”

LRC 040739 EU90-3.0 & ext. length 3.0”

LRC 040738 EU90

LRC 040740 EU90-4.5 & ext. length 4.5”

LRC 040738 EU90


Order Mfg.No. No. DescriptionAPL 201556 ACC-1803 EXT 3" extension

APL 201557 ACC-1804.5 EXT 4.5" extension

APL 201558 ACC-1806 EXT 6" extension


Order Mfg.No. No. DescriptionCBC 202426 L-180-W/3" 3" extension

CBC 202427 L-180-W/6" 6" extension

CBC 202428 L-180-W/9" 9" extension

CBC 202429 L0180-W/12 12" extension


Order Mfg.No. No. DescriptionGIL 022688 GKSKSM standard

GIL 112578 GKSKSMG with monel gasket

GIL 112580 GKSKSMGT with monel gasket, long pin

GIL 041799 GKSKSMT with long pin

GIL 076287 GKSKSMV with V grooves

GIL 074210 GKSKSMVT with V grooves, long pin


Order Mfg.No. No. DescriptionLRC 040745 ETE625R standard

LRC 112581 ETE625LR with V grooves


Order Mfg.No. No. DescriptionAPL 201559 ACCHSGHSG standard


Order Mfg.No. No. DescriptionCBC 200360 KS-KS-M-0000 standard



G


DescriptionUniversal splice for two connectors. Allows for in-line and right angle splicing.

DescriptionUsed to splice two chassis connectors. Enables splicing of anytype cable to any other with minimum losses.

Male Splice Adapter Non-Rotational

Female Splice Adapter

DescriptionHousing to housing coupling connector, eliminates theneed for coaxial jumpers and permits cascadability oftaps, etc.

Adapter - Splice Block


Order Mfg.No. No. DescriptionGIL 068185 GKSKSMNR standard

GIL 057119 GKSKSMNRT with long pin


Order Mfg.No. No. DescriptionLRC 040744 ETE625 standard, long pin


Order Mfg.No. No. DescriptionGIL 022687 GKSKSF standard

GIL 022686 GKSKSFS high current capability


Order Mfg.No. No.GIL 031073 GSPB

GIL 076289 GSPB-2.0

GIL 106714 GSPB-2.75


Order Mfg.No. No. Port SpacingLRC 040742 HSB 1.50"

LRC 071702 TSB through splice only


Order Mfg.No. No. Port SpacingAPL 201560 ACCPSB 2.25


Order Mfg.No. No. Port SpacingCBC 200354 PSPB 2.25



G


DescriptionAdapter provides extended length when sufficient cable is notavailable for installation. Can be installed with any pin type or.412 and .500 feed thru type connector.

Splice - In Line or Right Angle Adapter

Adapter-Chassis Mounting Connector to "F" Series Female

Extension Adapter-Connector to Equipment

DescriptionConverts pin type connector to "F" series female. 5/8-24 threads.

DescriptionSplices different diameters of coaxial of cables with chassisconnections. Can be used in right angle turn for pedestal typeinstallations where space is restricted.


Order Mfg.No. No.GIL 022905 GP90/180


Order Mfg.No. No. DimensionGIL 031880 GEXT-3-1 3.18"

GIL 030483 GEXT-6-1 6.0"

GIL 031088 GEXT-9-1 9.0"

GIL 031089 GEXT-12-1 12.0"


Order Mfg.No. No. DimensionAPL 201563 ACC-1.5 EXT 1.5" extension


APL 201565 ACC-4.5 EXT 4.5" extension





Order Mfg.No. No.GIL 037113 GCHBAFFKS



G


DescriptionDesigned to terminate 60 cycle and RFsignals on unused equipment ports.

Description“F” series to ‘KS’ entry.

Adapter-Chassis MountingConnector to "F" Series Male

"F" Female-'KS' Adapter AC (60 Hz) Power Blocking

"F" Female-'KS' Adapter

DescriptionConverts pin type connector to "F" series male.

"KS" Port Terminator

Description“F” series to ‘KS’ entry. Terminates 60 cycle AC.


Order Mfg.No. No.GIL 044447 G-CH-AFM


Order Mfg.No. No. ManufacturerGIL 004656 GF625CH Gilbert

GIL 049415 GF625CHT* Gilbert

LRC 040741 F625E LRC

APL 201562 ACC625CH Amphenol

CBC 200356 F625CH000 Cabel Con


Order Mfg.No. No. ManufacturerGIL 022030 GTRM Gilbert

GIL 041800 GTRMT* Gilbert

LRC 040743 625TRB* LRC

APL 201561 ACCTRM Amphenol

CBC 200357 TRM-00000000 Cabel Con


Order Mfg.No. No. ManufacturerGIL 037940 GF625CHDCB Gilbert

GIL 076086 GF625CHDCBT* Gilbert

LRC 109246 F625BE LRC

* Long pin version

Illustrations shown are pictured as a reference only.Actual product may vary from these illustrations.Artwork ©1996 Gilbert Engineering Co., Inc.



G

Cable & ConnectorsCable Pulling Lubricants

Heat Shrink TubingCANUSA

DescriptionCFTV heat shrinkable tubing is designed specifically to meetthe needs of the CATV industry. CFTV tubing provides anabsolutely waterproof seal and mechanical protection. CFTVtubing is easy to install and allows clean and easy connectorre-entry. The unique sealant that internally coats CATV tubingprovides selective strippability and a strong watertight bond tocable and cable jacket, yet, strips fast and clean for re-entry tothe connector splice. Heat indicator lines disappear when tub-ing has fully recovered producing an error free installation with-out scorching or cable damage.

Features• Shrink ratio of 3 to 1• Environmentally seals and mechanically protects• 7 standard sizes• Adhesive flows smoothly and will not drip• Selective Strippability to meet CATV industry needs• Balanced system: 3 synchronized components; stripes

change color, tubing shrinks, and sealant flows simultaneously

Installation Tests• When adequate heat is applied, heat reactive stripes

change color: blue to black• When color has changed, tubing is fully recovered• When color has changed, sealant has achieved

balanced flow• Adhesive flows without dripping• No cracks or splitting• No surface charring during installation


Order Mfg. Standard Internal Dia. Internal Dia. Nominal Total Wall Application RangeNo. No. Length Minimum (D) Maximum (d) Thickness (W) for General Use (Dia.)

CUS 600356 CFTV-750 48" (1.22 meters) 0.75" 19mm 0.22" 5.6mm 0.08" 2mm .24-.65" 6.0-16.5mm

CUS 600350 CFTV-1100 48" (1.22 meters) 1.1" 27.9mm 0.4" 10.2mm 0.08" 2mm .45-1.0" 11.5-25.0mm

CUS 600351 CFTV-1300 48" (1.22 meters) 1.3" 33mm 0.4" 10.2mm 0.08" 2mm .45-1.2" 11.5-30.0mm



CUS 600354 CFTV-2050 48" (1.22 meters) 2.05" 52.1mm 0.75" 19mm 0.08" 2mm .82-1.8" 21.0-45.0mm

CUS 600355 CFTV-2750 48" (1.22 meters) 2.75" 69.8mm 1" 25.4mm 0.08" 2mm 1.2-2.5" 30.0-63.0mm

Ordering GuidelinesTo order, specify product type, size, length, and coating.

CFTV - 1300 - 48 - TProduct Size Length CATV

Type Sealant

Standard Color Black with blue heat indicating stripes.Standard Length 48" lengths or as shown in dimension tableAlso available in 6", 12" and 24" lengths.

See page K-138 for trunk cable O.D. chart.



G

Cable & ConnectorsHeat Shrink

Heat Shrink TubingChoosing the Proper Size

.412 CableCanusa No. Connector Mfg. Connector Type

CFTV-1300 Gilbert GP412 seriesGilbert GRS412 series

CFTV-1100 LRC EM (F) 412 K/W series

.440 Cable (MC2)Canusa No. Connector Mfg. Connector Type

CFTV-1300 Gilbert GRS440 series

CFTV-1100 LRC 440MC2 series

.480 Cable (TX Series)Canusa No. Connector Mfg. Connector Type


.500 Cable Canusa No. Connector Mfg. Connector Type

CFTV-1300 LRC EM(F) 500 K/W series

CFTV-1500 Gilbert GP500CHA

CFTV-1700 Gilbert GRS500CHDUGRS500 series


CFTV-1500 Gilbert GRS500MC2 series


.540 Cable (Quantum Reach)Canusa No. Connector Mfg. Connector Type


CFTV-1300 LRC 540 QR series



CFTV-1300 LRC 565 TX series



CFTV-1300 LRC 625 K series

The heat shrink tubing must be large enough to fit over the con-nector and still shrink tightly to the cable. To properly affect awaterproof seal, lengths should be approximately 2" to 3"longer than a feedthrough or chassis mount connector and 4"to 6" longer than a splice connector.







CFTV-1700 Gilbert GP750CGHAGilbert GP750CHDU

GRS750 series

CFTV-1300 LRC EM(F) 750 K/W series


CFTV-1700 Gilbert GRS750MC2 series









CFTV-1700 Gilbert GRS875 seriesLRC 875 K series



CFTV-1700 LRC 1000 K & W series












G


DigiCon ConnectorANTEC



DIG 202475 D6 Digicon universal 6 series F connector

DIG 202474 D59 Digicon universal 59 series F connector

DIG 202480 RTC360-59/6FB Digicon connector compression tool

DIG 202481 RTC-Holster Digicon compression tool holster

DIG 202478 PSR59/6 Digicon coaxial cable prep tool

DIG 202479 PSC59/6 Digicon cable prep tool replacement blade

DIG 202476 SSBS Digicon sealing sleeves short black

DIG 202477 SSGL Digicon sealing sleeves long gray

DescriptionMarketplace needs are pushing the communications industrytowards the convergence of video, voice and data. Broadbandnetwork providers are engineering their systems for expandedbandwidth, two-way interactivity and digital and/or compresseddigital signals. ANTEC’s new Digicon "F" Connector is thesmart connector for subscriber interfaces in your advancedbroadband networks.

Features• High performance, sealed drop connector• Superior mechanical and electrical specifications• Conical swedge provides an efficient, environmental seal• One connector for Type 6 and one connector for Type 59• Unique installation tool for both connector types

Digicon Connectors have many advantages over thestandard F-fittings

• Digicon connectors were specifically designed to be usedwith the patented RTC 360 Radial Tamper Crimp tool.

• The connectors were designed with Internal SealingRings. When conicaly swedged, these rings from an O-Ring out of the cables outer jacket.

• The internal rings reduce radiation leakage, provide anexcellent seal for waterproofing, and improve the pull-outstrength of theconnector.

• F-Conn connectors are manufactured with a lenghthenedinternal ferrule to support the outer radial swedge andprovide a strong electrical connection.

• The inner wall of the connector is tapered. This taper aidsin the swedging process by ensuring that the connectorwill not collapse under the axial pressure of the swedge.

• Digicon Connectors have a rubber ring in the hex nut forprotection against water intrusion.

• The Digicon Connector system significantly reduces radiation leakage when compared to standard hex crimps

The ConnectorforDigital Transmission



G

Cable & ConnectorsEZF Conectors

EZ Twist™ Inoor Coaxial EZF® Coaxial Drop Cable Connector Drop Connector RAYCHEM

RAYCHEM

DescriptionA unique twist-on feature of the EZ Twist connector makeseasy installation possible on all cables commonly used in thehome, even fire-retardant cables with light jackets. A polymericring, designed for cable retention, secures the cable to con-nector interface. The outer polymeric shell seats the ring, andlocks the assembly on the port.

An installation aid is provided to assist in terminating the con-nector to the cable. Made of clear plastic, the aid allows visualinspection, proper cable location in the connector, and correctcenter conductor length.

EZ Twist connectors have many of the features installers havecome to rely upon with the EZF® connector. They are colorcoded red for RG59 cable and blue for RG6 cable. The cableis easily prepared with the EZF-T cable preparation tool. EZTwist connectors save labor and expense while providing highquality, dependable, and consistent terminations.

EZ Twist connectors are packaged in bags of 100, with 4 installaids and 20 subscriber labels.



RYC 144291 EZ Twist 59-S/T for RG59 single braid and tri--shield, color coded red

RYC 144021 EZ Twist 59-Q for RG59 quad shield, color coded light red

RYC 144290 EZ Twist 6-S/T for RG6 single braid and tri-shield, color coded blue

RYC 144020 EZ Twist 6-Q for RG6 quad shield, color coded light blue

DescriptionRaychem’s EZF connector is designed to reduce system RFleakage, maintenance calls and inventory. Prepackaged in aneasy-to-handle, pocket-sized cassette, only three connectortypes are needed; one for RG59 cable, one for RG6 and one forRG11. The EZF connector line has color-coded cassettes andferrules for easy identification; blue for EZF-6, red forEZF-59,and black for EZF-11. No crimp tools are needed; a common7/16” wrench will tighten and seal the EZF-6 and 59 connector,5/8" for EZF-11..

Environmentally sealed for aerial and pedestal applications.

Each cassette of RG59 and RG6 connectors contains 12 EZFconnectors; the RG11 cassette contains 6 connectors. EZF con-nector is compatible with ports that are .280” or longer.



RYC 082399 EZF-59 RG59 connector with black sealing sleeves for F ports less than .450" long

RYC 104483 EZF-59L RG59 connector with gray sealing sleeves for F ports .450" or longer

RYC 144018 EZF-6 RG6 connector with black sealing sleeves for F ports less than .450" long

RYC 144017 EZF-6L RG6 connector with gray sealing sleeves for F ports .450" or longer

RYC 095178 EZF-11 RG11 connector with black sealing sleeves forF ports .275" long



G


"F" Connectors

Gilbert for RG6 drop cable

Order Mfg.No. No. Hex SizeRG6, up to 40% braid

GIL 050080 GF-6-AH-S/312 .326

RG6, 41% to 78% braid

GIL 050080 GF-6-AH-S/312 .326

GIL 103779 GF-6-AH-S/322 .326

RG6, greater than 78% braid

GIL 035325 GF-6-AH-S/342 .326

RG6, quad shield

GIL 035325 GF-6-AH-S/342 .326

GIL 041667 GF-6-AH-S/357 .384




GIL 035324 GF-59-AH-S/290 .326

RG59, greater than 78% braid

GIL 040749 GF-59-AH-S/312 .326

RG59, quad shield

GIL 040749 GF-59-AH-S/312 .326

GIL 060455 GF-59-AH-S/342 .326

RG59, headend cable

GIL 060455 GF-59-AH-S/342 .326

GIL 043956 GF-59-AH-S/357 .384


Order Mfg.No. No. Hex SizeRG11, geater than 40% braid, with pin

GIL 043957 GF-11-AH-S/460 .100 & .475

RG11, quad sheild, with pin

GIL 060510 GF-11-AH-S/480 .100 & .475

Gilbert - Universal "F" ConnectorsOne connector fits all RG59 cables, one connector fits all RG6 cables

Order Mfg.No. No. Hex Size

GIL 119011 GF-59-AH-S/USA .360

GIL 119012 GF-6-AH-S/USA .360

LRC for RG59 drop cable


LRC 040952 F59CHI .324

LRC 100557 F59CHI .324

RG59, quad shield

LRC 084422 F59QS .324

RG59, headend cable

LRC 112593 F59HEC .324



LRC 040951 F59CHI .324

LRC 100533 F59CH .324

RG6, quad shield

LRC 089747 F59QS .360


Order Mfg.No. No. Hex SizeFor all RG7

LRC 122827 F7CH .470


Order Mfg.No. No. Hex SizeRG11, up to quad sheild

LRC 087204 F11QS .470

Just Drop


JST 202338 F59 .324

RG59, from 67% braid up to quad sheild

JST 202339 F59QS .324

RG6, up to 67% braid

JST 202340 F6 .324

RG6, from 67% braid up to quad sheild

JST 202341 F6QS .324

These tables are for reference purposes only. Installation procedures and manu-facturer variances may affect the type of connector to use.

For drop cable see Section G - Cable & Connectors



G


F-81 Connectors F-81 ConnectorsREGAL

Features• 1 GHz bandwidth with low loss characteristics• Flat F ports on both ends assure proper contact and

improve EMI shielding • Two lengths to accommodate in-line splicing, or wall plate

and demarcation plate applications• Nickel plated brass for increased corrosion protection and

installation ease

DescriptionRegal's F-81 connectors feature an industry exclusive - two flatF ports. Flat ports improve EMI shielding with a more uniformground, ensuring a quality connection for years to come.Available in 1.1" and 1.4" lengths, these F-81 connectorsaccommodate in-line splicing or wall plate and demarcationplate applications. Usable minimum length of either end is 1/2"to accommodate sealing sleeves and deep F male connectors.


Order Mfg.No. No. Length HardwareREG 127761 RF-81 1.10 no

REG 127760 RF-81H 1.40 yes

Specifications

Bandwith MHz 5-400 400-500 500-550 550-600 600-1000

Insertion loss .10 .10 .16 .16 .25max (dB)

Return Loss 20 18 17 16 15 (14)*min. (dB)

* RF-81 only


Order Mfg.No. No. Length HardwareGIL 004705 GF-81 1.06 yes

GIL 044453 GF-81A 0.81 no

GIL 044454 GF-81S 1.13 no


Order Mfg.No. No. Length HardwareLRC 088743 F-81 0.90 no

LRC 050544 F-81/ hdw 0.90 yes


Order Mfg.No. No. Length HardwareJST 202281 JD-81 0.84 no

JST 202282 JD-81HDW 0.84 yes

JST 202283 JD-81D 0.84 yes

JST 202336 JD-NUTS "D" flat 1 side nuts only for F-81



G

Cable & ConnectorsAdapters & Coaxial Connectors

N Type Adapters 50 Ohm Impedance


Order Mfg.No. No.APL 040479 82-100

Male to Male Splice

Female to Female Splice


Order Mfg.No. No.APL 040480 82-101

DescriptionRG 214 Male 50 Ohm N Type Connector

DescriptionRG 213 Male 50 Ohm N Type Connector

RG-213 Connector

RG-214 Connector


Order Mfg.No. No.PIC 101498 NMA234

GIL 057077 GIL GN821AHS/460


Order Mfg.No. No.GIL 072913 GN-214AHS/480



G

Cable & ConnectorsCross References

Cable to Connector Cross Reference COMM/SCOPE DROP CABLE TO GILBERT CONNECTOR

Connector part numbers for this cross reference were supplied by therespective connector manufacturer.

These guides are not a guarantee or an endorsement, but rather an aid inconnector selection. It is the customer's responsibility to select connectorsfor a specific cable by calling the manufacturer of the connector.



G


Cable to Connector Cross ReferenceBELDEN DROP CABLE TO LRC CONNECTOR

Connector part numbers for this cross reference were suppliedby the respective connector manufacturer. These guides are nota guarantee or an endorsement, but rather an aid in connectorselection. It is the customer's responsibility to select connectorsfor a specific cable by calling the manufacturer of the connector.



G

Cable & Connectors

Cable to Connector Cross ReferenceBELDEN DROP CABLE TO GILBERT CONNECTOR

Connector part numbers for this cross reference were suppliedby the respective connector manufacturer. These guides are nota guarantee or an endorsement, but rather an aid in connectorselection. It is the customer's responsibility to select connectorsfor a specific cable by calling the manufacturer of the connector.

Documents

TWS Sec_G