Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
TWO-SPEED DOORS
INSTALLATION and SERVICEMANUAL
(To Be Retained by Authorized Savaria Dealer)
© Savaria Corporation
PN 000597 (Rev. 12-m04-2010)
© Savaria Corporation1 of 1 PN #301409
Technical Documentation Modifications and Additions
Two-Speed Door Installation and Service Manual (PN 000597, Rev. 12-m04-2010)Note: Modifications between revisions are marked M, additions between revisions are marked A.
Section Details
ALL Updated company logo, name, and typeface M
IMPoRTaNT
The following details and provided documents replace or augment the published manuals and schematics. The most recent engineering changes and
enhancements are reflected in the notes below.
1Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
TABLE Of CONTENTS
1. PRE-INSTALLATION INSTRUCTIONS AND NOTES 21.1 INTRODUCTION 3
1.2 TOOLS AND MATERIALS REqUIRED 4
1.3 ChECk ThE ShIPPINg CARTONS 4
1.4 PRE-INSTALLATION REqUIREMENTS 5
1.5 CAB PLACEMENT 5
2. INSTALLATION PROCEDURES 62.1 INSTALLINg ThE LANDINg DOOR ASSEMBLy 6
2.1 INSTALLINg ThE CAR DOOR OPERATOR
AND CAR DOORS 32
3. SUPRA BOARD 553.1 POWER SUPPLy 55
3.2 SAfETy CIRCUIT 55
3.3 SERVICE TEST MODE 55
3.4 LEDS 56
3.5 DIP SWITChES 57
3.6 INTERfACE WIRINg 58
A. DOOR OPERATOR DIAgNOSTICS AND TROUBLEShOOTINg A-1
B. TWO-SPEED DOORS PARTS LIST B-1
C. IMPORTANT MEASUREMENTS C-1
D. kEyWAy TEMPLATE D-1
2 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1. PRE-INSTALLATION INSTRUCTIONS AND NOTES
Standard Notations
Throughout this manual, important information is highlighted by the headings WARNING, CAUTION, or NOTE. These words are defined as follows:
WARNING – Warnings are used to indicate instructions, which if not followed correctly, could result in death or serious personal injury, or substantial damage to equipment.
CAUTION – Cautions are used to indicate instructions or information, which if not observed, could result in damage to the equipment.
NOTE – Notes are used to indicate instructions or information which is helpful in understanding and operating the equipment, and which will usually speed up the installation process.
ThIS SAfETy ALERT SyMBOL INDICATES AN IMPORTANT MESSAgE IN ThIS MANUAL. WhEN yOU SEE ThIS SyMBOL, READ ThE MESSAgE CAREfULLy AND BE ALERT TO ThE POSSIBILITy Of CAUSINg DAMAgE TO ThE EqUIPMENT AND/OR PERSONAL
INjURy.
3Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1.1 INTRODUCTION
This manual contains installation and service instructions for the SAVARIA TWO-SPEED DOORS. Please follow the instructions provided in this manual and call us immediately if you have any problems or need assistance.
During installation, do not try to “cut any corners”, eliminate any installation steps or modify the SAVARIA TWO-SPEED DOORS. It is important for your customer’s safety that the installation is thorough and correct. The best way to ensure their safety is by following the instructions provided in this manual.
hELP LINEIf you have any questions that are not covered in this manual, please contact our Technical Support Department for assistance. Please have the following information available before calling to receive the fastest service possible:
• JobNumber• JobName• Location• ProductType• InitialorFollow-upVisit• BriefDescriptionofProblem• CallBackNumber
SAVARIA107 Alfred kuehne Blvd.
Brampton, Ontario, Canada L6T 4k3Telephone: (905) 799-5484U.S. Toll free: (800) 791-7999fax: (905) 791-2222
IT IS RECOMMENDED ThAT yOU READ AND fULLy UNDERSTAND ThIS MANUAL BEfORE BEgINNINg ThE
INSTALLATION Of ThE TWO-SPEED DOORS.
4 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1.2 TOOLS AND MATERIALS REqUIRED
The following tools and materials are required to install the two-speed landing doors:
Carpenter’s square
Level
Plumb bobs
Gaugesticks(1/4"and3/16")forsettingdoorclearance
Concretehammerdrillwith3/8"-1/2"bits
Shims
Tape measure
Ratchet and extension (minimum 12")
Socketheadwrenches(7/16"and9/16")
Socketheadwrenches(Allenkeys)-4mm,5mmand6mm
Screwdrivers (flat and Phillips)
Door pressure gauge
Battery-operated,variable-speeddrillwith5/32"and11/64"drillbits
Standardimperialwrenchandsocketset
1.3 ChECk ThE ShIPPINg CARTONS
Westronglyrecommendthatyouconductapre-installationcheckwhenyoureceiveshipmenttoverify the contents for damaged or missing parts. Uncrate all boxes and spread out the parts. Carefully checkforanydamageandreportittoyourcarrierimmediately.Checkforanymissingpartsagainstour shipping list.
NOTE
NO CLAIMS FOR SHORTAGE WILL BE ALLOWED UNLESS REPORTED WITHIN 24 HOURS OF RECEIPT OF SHIPMENT.
5Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1.4 PRE-INSTALLATION REqUIREMENTS
Ensurethefollowingtasksarecompletebeforeinstallingthetwo-speedlandingdoors:
1. Ensure there is adequate support for the hoistway (landing) door frame.
2. It is recommended that installers who are not familiar with two-speed door installation completely assemble the cab and ensure it is plumb, level and square.
3. Refer to the drawing in Appendix C for measurements that are important during the installation.
1.5 CAB PLACEMENT
Use the following guidelines for cab placement:
1. RefertotheInstallationDrawing‘PLANVIEW’shippedseparatelywiththeelevatorforexactcabplacement.
2. Settheedgeofthecabplatform5-3/4"fromthecenterofeachguiderail.
3. Setthecabsill6-3/4"fromtheedgeofthelandingatthetightestspotofthehoistway.
4. Thetype2cabdaylightlineis2-1/4"fromtheedgeofthecarsill.RefertothePlatformInstallationsection in the Orion Installation Manual for detailed information on platform (cab) placement and the location of the daylight line.
5. It is recommended that the cab be completely assembled and be plumb and square so that the landingdoorassemblycanbesettoEXACTLYmatchthecab(exceptwhenthetotaltraveldoesnotallow forenough roomtoworkon topof thecar -90"or less).Thecar sill to landing sillclearanceandcaroperatorclutchtolandingdoorrollersclearanceareCRITICAL.
6 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
2. INSTALLATION PROCEDURES
2.1 INSTALLINg ThE LANDINg DOOR ASSEMBLy
Note: This section describes installation for a right-hand door assembly. A left-hand door assembly is an exact mirror image with respect to any 'handed' parts.
Figure1illustratesthecomponentsofthetwo-speedlandingdoorassembly.
Figure1LandingDoorAssemblyComponents
Strike jamb(252067-P)
Pass jamb(252089-P)
Head jamb(252071-P)
Sight guard(252066)
Header(252078)
Bracket (252228)
Door hanger assembly(301367)Strut angle
tie (250335)
Sill assembly(252472)
Strut angletie (250335)
Strut angletie (250335)
Slow landingdoor (252104-P)
Strut (252057)
Strut (252057)
Strut angletie (250335)
Fast landingdoor (252104-P)
7Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 1
Followtheprocedurebelowtotransferthedaylightlinefromthecabfloortothelanding.
1. Determineandmarkthecabdaylightline.SeeFigure2.
2. At the edge of the cab, transfer the daylight line from the cab floor to the landing. Extend the daylight line 90° downwards into the hoistway.
Figure2DaylightLine
8 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 2
Bringthesillassembly(PN252472)intothehoistway.
Step 3
Align the sill assembly with the daylight line.
Whenlookingintothedoorwayfromthelanding,lineupthedaylightlinewiththeinsideedgeoftheright-handjambbracketonthesillassembly.SeeFigure3.
Step 4
Followtheprocedurebelowtosettheheightofthesillassembly.
1. Determine the height of the finished floor.
2. Determine the grout angle plate installation depth.
3. Fastenthetemporaryboltsforthesillheightadjustmentplates(PN252132)tothelandingfloor.SeeFigure5onthenextpage.
Note: Never drill through a finished floor to install the sill height adjustment plates.
Figure3SillAssembly
Jamb bracket
Daylight line
Hoistway sideLanding side
36”
9Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
4. Thesillheightadjustmentplates(seeFigure4)allowyoutoraisetheheightofthesillassemblyto ensure that the top of the grout angle plate remains 2-1/2'' lower than the finished floordimension when adding grout.
Note: You can leave the plates installed once grouting is complete if you're building a finished floor on top of the plates.
5. Adjustthetorquebolts(PN105863)onthesillheightadjustmentplatesuntilthegroutangleplateis2-1/2''lowerthanthefinishedfloordimension.SeeFigure5.
Note: The sill must be level with the finished floor of the landing.
Figure4SillHeightAdjustmentPlates
Sill heightadjustment plate
Hoistway sideLanding side
Sill heightadjustment plate
Figure5AdjustSillHeight
2-1/2"
Grout angle plate
Finishedfloor
Torque boltTemporary boltto fasten plateto landingAdjustment plate
Temporary boltto fasten plateto landing
Adjustment plate Torque bolt
10 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 5
Followtheprocedurebelowtolevelthesillandattachittothebuildingstructure.
HardwareRequired
Anchor bolt, hollow wall, 1/4" x 3" PN 103639 Qty = 5
OR
Anchor bolt, concrete wall, 13/8" x 3" PN 103640 Qty = 5
1. Levelthesillassembly.
2. From inside the hoistway, attachthe sill assembly to the building structure at the door wall using five3"anchorbolts(seeFigure6).Ensure the full length of the bolts reaches the load bearing wall.
Step 6
Set the gap (running clearance) between thelandingsillandthecarsillto1.25"(seeFigure7).Ensurethegapisthesamealongthefulllengthof the sill.
Ifthegapisnot1.25",loosenthethreeboltsunderneaththelandingsillassembly(seeFigure7),adjustthe sill assembly in or out as required, and then tighten the three bolts.
Figure 6 Attach Sill Assembly to Building Structure
Hoistway side
Landing side
Figure 7 Gap Between Landing Sill and Car Sill
Car sill
Landing sill
1.25” sill to sill
Loosen 3 bolts and adjust sillas required to achieve gap
View from underneath sill
11Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 7
Attach the right strut (PN 252057) to the sill assembly using two 1" hex head bolts (one on each side of thestrut).SeeFigure8.
Note: Eachbolthasaflatwasherontheheadsideofthebolt,andaflatwasher,lockwasherandnuton the stem side of the bolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 2
3/8" flat washer PN 102188 Qty = 4
3/8" lock washer PN 102191 Qty = 2
38"-16 hex nut PN 102186 Qty = 2
Figure8AttachRightStruttoSill
Right strut(PN 252057)
Sill assembly(PN 252472) Bolt here
Bolt here
12 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 8
Looselyattachthetop right strut angle tie (PN 250335) to the right strut using two 1" hex head bolts. Fingertightenthebolts.SeeFigure9.
Note: Eachbolthasaflatwasherontheheadsideofthebolt,andaflatwasher,lockwasherandnuton the stem side of the bolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 2
3/8" flat washer PN 102188 Qty = 4
3/8" lock washer PN 102191 Qty = 2
38"-16 hex nut PN 102186 Qty = 2
Figure9AttachTopStrutAngleTietoRightStrut
Top rightstrut angle tie(PN 250335)
Bolt angle tieto right strut
13Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 9
Anchor the top right strut angle tie (PN 250335) to the building structure using two 3" anchors. See Figure10.
HardwareRequired
Anchor bolt, hollow wall, 1/4" x 3" PN 103639 Qty = 2
OR
Anchor bolt, concrete wall, 13/8" x 3" PN 103640 Qty = 2
Figure10AnchorTopRightStrutAngleTietoBuildingStructure
Top rightstrut angle tie(PN 250335)
Anchor angle tieto wall or header/lintel
14 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 10
Attach the bottom right strut angle tie (PN 250335) to the right strut using two 1" hex head bolts. See Figure11.
Note: Eachbolthasaflatwasherontheheadsideofthebolt,andaflatwasher,lockwasherandnuton the stem side of the bolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 2
3/8" flat washer PN 102188 Qty = 4
3/8" lock washer PN 102191 Qty = 2
38"-16 hex nut PN 102186 Qty = 2
Figure11AttachBottomStrutAngleTietoRightStrut
Bottom rightstrut angle tie(PN 250335)
Bolt angle tieto right strut
15Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 11
Anchor the bottom right strut angle tie (PN 250335) to the building structure using two 3" anchors. SeeFigure12.
HardwareRequired
Anchor bolt, hollow wall, 1/4" x 3" PN 103639 Qty = 2
OR
Anchor bolt, concrete wall, 13/8" x 3" PN 103640 Qty = 2
Note: Tighten all bolts.
Figure12AnchorBottomRightStrutAngleTietoBuildingStructure
Anchor angle tie tobuilding structure/landing
Bottom rightstrut angle tie(PN 250335)
16 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 12
Repeat steps 7 through 11 for the left strut.
• Attach the left strut (PN 252057) to the sill assembly. • Attach the top left strut angle tie (PN 250335) to the left strut. • Attach the top left strut angle tie (PN 250335) to the building structure. • Attach the bottom left strut angle tie (PN 250335) to the left strut. • Attach the bottom left strut angle tie (PN 250335) to the building structure.
17Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 13
Followthestepsbelowtoattachthelandingdoorhangerassembly(PN301367-righthand;PN301368-lefthand)tothestrutsusingfour1"hexheadboltsoneachside.SeeFigure13.
Note: Eachbolthasaflatwasherontheheadsideofthebolt,andaflatwasher,lockwasherandnuton the stem side of the bolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 8
3/8" flat washer PN 102188 Qty = 16
3/8" lock washer PN 102191 Qty = 8
38"-16 hex nut PN 102186 Qty = 8
1. Drop the landing door hanger assembly onto the right and left struts at the same time.
2. Attach the right side of the door hanger assembly to the right strut using four 1" hex head bolts. Besuretoinstallallfourbolts.
3. Attach the left side of the door hanger assembly to the left strut using four 1" hex head bolts. Besuretoinstall all four bolts.
4. Set the height from the bottomof the door trackto the top of the door sill to82-3/4"(2107mm).
5. Square the frame.
6. Plumb the frame in bothdirections.
7. Tighten all previously installed hardware.
Figure13AttachDoorHangerAssemblytoStruts
Landing doorhanger assembly(PN 301367)
Bolt hanger assemblyto left strut
Bolt hanger assemblyto right strut
Plumb the framein both directions
82-3/4"(2107 mm)
18 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 14
Attachtheheadjamb(PN252071-Pforrighthand;PN252093-Pforlefthand)tothehangerassemblyusingtwo1"hexheadboltsinstalledfromthehoistwayside.SeeFigure14.
Note: Eachbolthasaflatwasherandlockwasherontheheadsideofthebolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 2
3/8" flat washer PN 102188 Qty = 2
3/8" lock washer PN 102191 Qty = 2
Note: Theheadjambishanded.Thedeepersideisalwaysonthestrikejambside.Also,theheadjambmustoverhangthestrikeandpassjambby1/4''onthelandingside.
Note: Inthenextstep,aboltbracket(PN252228)willbeinstalledontopoftheheadjambtoconnecttheheadjambtothedoorhangerandthestrikejamb.
Figure14AttachHeadJambtoDoorHangerAssembly
Head jamb(PN 252071-P)
Bolt head jambto door hanger
Hoistway side
Landing side
19Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 15
Followtheprocedurebelowtoattachthestrikejamb(PN252067-P)totheheadjambandthesill.SeeFigure15.
Note: Forattachmenttotheheadjamb,eachbolthasaflatwasherontheheadsideofthebolt,andalockwasherandnutonthestemsideofthebolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 3
3/8" flat washer PN 102188 Qty = 5
3/8" lock washer PN 102191 Qty = 5
38"-16 hex nut PN 102186 Qty = 5
1. Place the boltbracket(PN252228)ontopoftheheadjambattheright.Usea1"hexheadbolttoattachtheboltbrackettothedoorhangerthroughthetopleftholeintheboltbracket.
2. Attach the strike jamb to thehead jamb using two 1" hex headbolts.Makesuretherearbolt is threaded through the boltbracket.
3. Secure the strike jamb to thejambbracket on the sill usingaflatwasher, lockwasher andnut on the stem side of each jambbracketbolt.
4. Ensure the strike jamb is flushwith the sill in the slotted holes.
5. Ensure that when you're in the hoistway looking out, theinsideedgeofthestrikejambis4'' from the outside of the strut. Ensure that both are straight.
Figure15AttachStrikeJambtoHeadJambandSill
Head jamb(PN 252071-P)
Bolt head jambto strike jamb
Strike jamb(PN 252067-P)
Attach bolt bracket(PN 252228) todoor hanger
20 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 16
Followtheprocedurebelowtoattachthepassjamb(PN252089-P)totheheadjambandthesill.SeeFigure16.
Note: Forattachmenttotheheadjamb,eachbolthasaflatwasherontheheadsideofthebolt,andalockwasherandnutonthestemsideofthebolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 2
3/8" flat washer PN 102188 Qty = 4
3/8" lock washer PN 102191 Qty = 4
38"-16 hex nut PN 102186 Qty = 4
1. Attachthepassjamb(PN252089-P)totheheadjambusingtwo1"hexheadbolts.
2. Securethepassjambtothejambbracketonthesillusingaflatwasher,lockwasherandnutonthestemsideofeachjambbracketbolt.
Figure16AttachPassJambtoHeadJambandSill
Pass jamb(PN 252089-P)
Bolt head jambto pass jamb
21Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 17
Plumbandsquarethelandingentranceframeandtightenallhardwarewhencomplete.SeeFigure17.
Figure17PlumbingandAnchoringEntranceFrame
22 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 18
Verifythattheopeningbetweenthestrikejambandthepassjambis36".SeeFigure18.
Alsoverifythattheheadjamboverhangsthestrikeandpassjambby1/4''onthelandingside.
Figure18Verify36"Opening
Pass jamb Strike jamb
36” entrance opening
36” opening
1/4” overhang
23Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 19
Followtheprocedurebelowtoinstallthelandingdoors(PN252104-P)usingfour1"hexheadbolts(twoperdoor).SeeFigure19.
Note: Eachbolthasaflatwasherandlockwasherontheheadsideofthebolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 4
3/8" flat washer PN 102188 Qty = 4
3/8" lock washer PN 102191 Qty = 4
3/8"-16 weld nut PN 103685 Qty = 4
1. Positiontheslowdoorontopofthesill.Dropaweldnut103685intoeachofthetwoslotsonthetopofthedoor.Securethedoortothehangerusingtwohexheadbolts(3/8''-16x1'')withalockwasherandaflatwasherforeachbolt(ontheheadside).SeeFigure19.
Note: Makesurethereisa1/4''gapbetweenthetopofthesillandthebottomofthedooronbothsides.Youmayhavetoshimthespacebetweenthehangerandthetopofthedoorusingthe supplied shims.
View from hoistway side
Fast door
Slow door
Ensure 1/4” gapbetween top of silland bottom of door(on both sides)
Figure19InstallLandingDoors
24 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
2. Pre-assemblethesiteguard(PN252066)totheinsideleadingedgeofthefastdoor.
3. Positionthefastdoorontopofthesill.Dropaweldnut103685intoeachofthetwoslotsonthetopofthedoor.Securethedoortothehangerusingtwohexheadbolts(3/8''-16x1'')withalockwasherandaflatwasherforeachbolt(ontheheadside).SeeFigure19.
Note: Makesurethereisa1/4''gapbetweenthetopofthesillandthebottomofthedooronbothsides.Youmayhavetoshimthespacebetweenthehangerandthetopofthedoorusingthe supplied shims.
4. Ensurethereisa1/4"gapbetweentheslowandfastlandingdoors(Figure20).Adjustasrequiredto achieve the correct gap.
5. Ensurethereisa1/4"gapbetweentheslowspeedlandingdoorandthepassjamb(Figure20).Adjust as required to achieve the correct gap.
Note: These distances are a starting point only. The doors may require additional adjustment.
1/4” gapbetween doors1/4” gap
between pass jamband slow door
Figure20GapBetweenDoors
slow door
fast door¼"
¼"pass jamb
strike jamb
25Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 20
Followtheprocedurebelowtoinstallthedoorgibs(gibpackagePN301111)andfireretainergibs(PN301339).
1. Install two door gibs on the bottom of each door and secure with the hardware provided. See Figure21.Bendthefiretabsonthedoorgibs.
Note: Thedoorgibsareadjustableinordertoensurethereisa1/4"gapbetweenthedoors.
2. Position the fire retainer gib at the pre-drilled holes on the inside trailing edge of the landing door.Securethefireretainergib(showninFigure22)withthehardwareprovided.
3. Adjust the gibs to ensure the doors are not binding (as required).
Figure22InstallingFireRetainerGib
PN 301339
Install fire retainer gib betweeninstalled door gibs as shown
Figure21InstallingDoorGibs
Install door gibs on thebottom of each door as shown
26 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 21
Install the two rubber bumpers (PN 100737) on the strike jamb - one at the top and one at thebottom.
Move the door hangers to the fully closed position against the bumper. Adjust the doors until the upper andlowerleadingedgeofthefastdoorpanelis1/16"to1/8"fromthestrikejambrubberbumper.Ifnecessary, add shims between the door and hanger.
Step 22
Plumb the doors. Ensure that both doors, when fully open, are even.
Note:Makesurethereisa1/4''gapbetweenthetopofthesillandthebottomofeachdooronbothsides.Youmayhavetoshimthespacebetweenthehangerandthetopofthedoorusingthesuppliedshims. Tighten the hanger bolts to secure the door.
Step 23
Runtheinterlockwirestothehallstationsandconnectperthewiringdiagrams.
Step 24
Verifythatthedoorsopenandclosesmoothly.
Note: If the doors close too harshly, release a turn or two of retractor wire tension until the doors close without too much tension.
Properly adjusted doors will open with a single finger pull.
Properlyadjusteddoorswillcloseontheirownretractor(doorcloseorspirator)force.Checkthisbystopping the door while it's closing and it should continue to close under its own force, especially during the last 2" of closing.
27Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 25
Attachtheheader(PN252078)tothestrutsusingtwo1"hexheadbolts.SeeFigure23.
Note: Eachbolthasaflatwasherontheheadsideofthebolt,andaflatwasher,lockwasherandnuton the stem side of the bolt.
HardwareRequired
3/8"-16 x 1" hex head bolt PN 102197 Qty = 2
3/8" flat washer PN 102188 Qty = 4
3/8" lock washer PN 102191 Qty = 2
38"-16 hex nut PN 102186 Qty = 2
Figure23AttachHeadertoStruts
Header(PN 252078)
Bolt headerto left strut
Boltheader toright strut
28 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Figure25UnlockingDeviceandKey
Figure24InstallUnlockingDevice
Step 26
Followtheprocedurebelowtoinstallthelandingdoorunlockingdevice(PN301385-righthand;PN301386-lefthand).
1. SeeFigure24below.Securetheunlockingdevice(1)tothelandingdoorhanger(2)withscrews(3). Note that the screws will self-tap into the holes on the hanger.
2. Movetherod(4)upanddowntoverifyproperoperation.SeeFigure25.
3. Drillaholeforthedoorkey(PN301334)usingthetemplateprovidedinAppendixDandinstallthe bezel.
Note: Theholemustbe3.5"fromthetopofthedoorand6"fromtheedgeofthedoorasshownin the template.
Note: Whenusingthedoorkeytounlockthedoorfromthehallway,ALWAYSturnthedoorkeytowardstheleadingedgeofthedoor(counter-clockwiseforright-handdoors;clockwiseforleft-hand doors).
Note: Doors are not exactlyas shown here.
29Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 27
Followtheprocedurebelowtoadjustthelandingdoors.
1. Verifythedoorhangersareplumb.Shimasnecessaryatlocation'A'(seeFigure26)betweenthedoorhangerandthetopofthedoor.Makesureyoubendtheshimsdowntoavoidhittingtheother door.
Note: It is crucial that the door hangers are plumb. If the door hangers are not plumb, the hanger-mountedclutchwillnotengagethepick-uprollers.
2. Slackentheupthrustroller,thenlevel,raiseandlowerthelandingdoorbyadjustingtheeccentriconthebackroller(1)witha4mmAllenwrench.
3. Aftermakingalladjustments,settheeccentricupthrustbearing(2)witha4mmAllenwrenchandrunthedoortocheckforrubbing.
Figure26AdjustLandingDoors
30 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
4. Verifythegapintheinterlockassemblyisapproximately1/8"(3.2mm).SeeFigure27.
5. Installtheinterlockcoverandtightenthescrews.
6. Checkthatthereisaspaceof0.06"(0.15mm)betweentherollerandtherail.SeeFigure28.
Figure27VerifyInterlockGap
Figure28SpaceBetweenRollerandRail
31Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 28
Followtheprocedurebelowtoadjustthedoordriverollers.
1. If adjustment is necessary, loosen the set screws (2) and adjust door drive rollers (1) in or out.
2. Verifydimensionbetweentheinsideofthedoordriverollers(1)is1-1/4inches(32mm)andtheoutsideofthedoordriverollersis3-3/4inches(101mm).
3. If adjustment is necessary, loosen screws (3), and move door drive rollers. Tighten screws (3) after adjusting.
4. Makesurethereis3/8inch(10mm)clearancebetweenthefrontofthedoordriverollers(1)andtheedgeoftheplatform.RefertoFigure29.
Figure29AdjustingDoorDriveRollers
3 ¾ in.
Alternate hole for larger roller clearance. Bolt will self-tap.
32 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
2.2 INSTALLINg ThE CAR DOOR OPERATOR AND CAR DOORS
Note: This section describes installation for a right-hand door assembly. A left-hand door assembly is an exact mirror image with respect to any 'handed' parts.
Thecardooroperatorisacompleteassemblyconsistingofthefollowing(seeFigure30):
• Door operator and car door hanger/header (1) • Clutch (2) • Door switch/contact (3)
Theillustrationsonthenextpages(Figures31and32)showthevariouscomponentsofthecardooroperator assembly.
Figure30CarDoorOperatorAssembly
33Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Door operator anglemounting bracket
Figure31CarDoorOperatorAssemblyInstalled
Door operator
Header mounting bracket Carriage Bolt
34 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Figure32CarDoorHangerandClutchAssembly
Motor encoder
Motor
Clutch vanes
Car door hangerassembly
Rear C track
Bumper
C track carriagebolts (x5)
35Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 1
Beforeinstallingthecardooroperator/hangerassembly: •Verifytheplatformislevel. •Verifythesillislevel. •Verifythecabisplumb. • Verifytheheaderislevel.
Followtheprocedurebelowtoinstallthecardooroperatorassembly.
1) Loosenthefourscrews(1)andremovethedooroperatorboardcover(2).SeeFigure33.
2) Insertfive5/16x24x1.25"carriageboltsintotherearCtrackofthedooroperatoratthemotorend.Place theboltheads in theC tracksuch that thestemsarepointingupward through theopening.
3) First,attachtheZbrackettothedooroperator(Figure34),ensuringthatitisorientedasshownbelow.SecuretheZbrackettothedooroperatorwithanutandwasheroneachofthefivecarriagebolts.
Figure33RemoveDoorOperatorBoardCover
Figure34ZBracketandCarriageBolts
Carriage bolt
Z bracket
Door operator
Z bracket
36 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
4) Next, attach the twoanglemountingbrackets to thedooroperatorusing twobolts and theappropriatefastenersforeachbracket.SeeFigure35.Younowhaveadooroperatorassemblyconsistingofthedooroperator,Zbracketandtwoanglemountingbrackets.
Figure35AttachAngleMountingBracketstoDoorOperator
Attach anglemountingbrackets todoor operator
5) Checkthattheheadermountingbracketislevel.
Note: Two people are required to complete the next step.
6) PositionthedooroperatorassemblysothefiveholesintheZbracketlineupwiththefivepre-installedboltsontheheadermountingbracket.Dropthedooroperatorassemblyontotheheadermountingbracket.
Figure36SecuretoHeaderMountingBracket
Secure hereat five locations
Headermountingbracket
Z bracket
Z bracket
Headermountingbracket
37Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
7) Securewithanut,washerandlockwasherateachofthefivebolts.SeeFigure36.
8) Attachthetwoanglemountingbracketstothecabceilingandsecurethemusingtwo5/8"springnutsperbracket(insertedintothetracksonthecabceiling)andtheappropriate5/8" hardware. Figure37showsoneoftheanglemountingbrackets.
Figure 37 Attach Angle Mounting Brackets to Cab Ceiling
Attach to cab ceiling
9) Ensure the door operator assembly is level and plumb, and shim if necessary.
Insert spring nuts into tracks
38 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 2
Levelthecardooroperator/hangerassembly.
1. Use a two-foot level to verify that the car door hanger assembly is level.
2. Check that the distance from the car sill to the bottom of the door track is 82-3/4" + 1/8", - 1/16"(2107mm).SeethesampleinstallationshowninFigure38.
Figure38DistanceFromCarSilltoBottomofDoorTrack
82-3/4"(2107 mm)
Car sill
Bottom ofdoor track
39Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 3
Checkthedistancebetweenthecardoorandlandingdoortracks.
1. Checkthatdimension'A'betweenthecardoortrackandthelandingdoortrackis4-13/16" (122 mm).SeeFigure39.
2. If dimension 'A' is not 4-13/16" (122 mm), verify the cab is plumb.
Figure39CheckMotorClearanceAgainstLandingSillLine
2 spd
4-13/16"
40 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 4
Ensure the center of the car door operator bumper is aligned with the center of the landing door operatorbumper.SeeFigure40.Makeadjustmentsasrequired.
Figure40AlignDoorBumpers
Landing door bumper
Car door bumper
41Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 5
Followtheprocedurebelowtoinstallthecardoors.
1. Positiontheslowdoorontopofthesill.Dropaweldnut(PN103685)intoeachofthetwoslotsonthetopofthecardoor.Securethedoortothehangerusingtwohexheadbolts(3/8''-16x1'')withalockwasherandaflatwasherforeachbolt(ontheheadside).
Note: Makesurethereisa1/4''gapbetweenthetopofthesillandthebottomofthedooronbothsides.Youmayhavetoshimthespacebetweenthehangerandthetopofthedoorusingthe supplied shims. Tighten the hanger bolts to secure the door.
2. Positionthefastdoorontopofthesill.Dropaweldnut103685intoeachofthetwoslotsonthetopofthecardoor.Securethedoorthehangerusingtwohexheadbolts(3/8''-16x1'')withalockwasherandaflatwasherforeachbolt(ontheheadside).SeeFigure41.
Note: Makesurethereisa1/4''gapbetweenthe top of the sill and the bottom of the door on both sides. Youmayhavetoshimthe space between the hanger and the top of the door using the supplied shims. Tighten the hanger bolts to secure the door.
3. Ensurethereisa1/4''gap between the slow and fast doors.
4. Install bumpers on the slam post.
5. Ensure that both doors, when fully open, are even.
6. Installthedoorgibstothemountingplateunderthecardoorsusingthesameprocedureasforthe landing doors.
Note: Car doors do not require a fire retainer.
Figure41InstallCarDoors
Drop weld nutinto each slot
42 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 6
Followtheprocedurebelowtoadjustthecardoors.
1. Movethedoorhangers(1)tothefullyclosedpositionagainstthebumper(2).SeeFigure42.
Note: Theleadingedgeofthedoorpanelshouldbarelymakecontactwiththestrikejambrubberbumpers.
3. Adjustthedoorsuntiltheupperandlowerleadingedgeofthedoorpanelmakescontactwiththestrikejamb.Ifnecessary,addshimsbetweenthedoorandthehangerboltplate.
4. Verifytheclearancebetweenthedoorandsillis1/4".
M d
Figure42AdjustCarDoors
43Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 7
Followtheprocedurebelowtosettheeccentricsonthecardoorhangers.
1. Verifythegapbetweentheeccentricroller(1)andtherail(2)is1/64"(0.3mm).SeeFigure43.
2. Open and close the doors to verify the clearance is consistent.
3. If the eccentric roller (1) needs adjustment, loosen the nut (3) and use an Allen wrench to turn the roller shaft (4),
Figure43VerifyGapBetweenRollerandRail
44 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 8
Followtheprocedurebelowtocheckthedoorcontacts.
1. Whenthedoorlockpins(1)areJUSTtouchingthedoorcontacts(2),verifythemeasurement'A'betweenthedoorhanger(3)andthebumper(4)is1/8"(3mm).SeeFigure44.
2. Ifmeasurement'A'isnot1/8"(3mm):
a) Loosenthescrews(5).
b) Movethebrackets(6).
3. Recheckmeasurement'A'.
Note:Thedoorshouldstopagainstthestrikejambbumpers,notagainstthebumper(4).
Figure44CheckDoorContacts
45Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 9
Followtheprocedurebelowifyouneedtolocktheclutchopentocheckclearancesandalignments.
1. Locktheclutchopentocheckclearancesandalignmentsasfollows(seeFigure45):
a) Removethescrew(1)fromtheparkingpositionintheupperrightcorneroftheclutch.
b) Open the clutch vanes.
c) Installthescrewinthelockpositionhole(2)asshowninFigure45toholdtheclutchopen.Be sure to remove this screw at the end of the procedure once all clearances are verified.
2. Placeapieceofmaskingtapeonthelandingsillandmarkaline5-3/4"fromthedaylightline.
Note: Thecenterlineofthedoordriverollersandtheclutchshouldbe5-3/4"fromthedaylightline.
Figure45LockClutchOpen
The distance between guide vanesis 4 ¾" (3 ⅛" collapsed).
Center Line
46 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
3. Markaline2-3/8"oneithersideofthedaylightline.Drivethecardownandensuretheinsideedges of the clutch vanes align with these two lines.
4. If the alignment is out by a small amount, the landing door drive rollers can be adjusted. If the alignment isoutbymorethan3/8",centertheclutchasrequriedbyslackeningtheboltsthatsecuretheoperatortotheheadermountingbracket.
5. Adjustthedoorpositionandre-checktheoperatorforplumbandlevel.
6. Runthecardownslowly,stop before the vanes engage the rollers, and confirm that there is clearance between the rollers and the clutch.
7. Drive the car down to the floor level and confirm the proper running clearance between the clutch and door drive rollers.
8. Loosenthethreescrewsthatareusedtopositiontherollersandsettherollers3-3/4"(95mm)apart, outside to outside. Tighten the three positioning screws and repeat for each landing. Refer to the section, Check the Spacing of the Door Drive Rollers.
9. Ensure there is a 1/2" clearancebetween the clutch vanes and the rollers.The rollers canbeadjusted in and out by loosening the set screw in the center of the roller and positioning the roller. Tighten the set screws after adjustment.
10. Afteradjustingtherollers,checktheclearancebetweenthedoordriverollersandthecarsill.
11. Once all clearances are verified, be sure to remove the screw from the lock position and return ittotheparkpositionintheupperrightcorneroftheclutch.
47Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 10
Followtheprocedurebelowtocheckthecardoorhangerandclutch.
Caution:Makesurethecardoorhangerandthetopof theclutchARENOTplumb;otherwise, theclutch will hit the door operator board cover.
1. Plumbtheclutchvanes(3).SeeFigure46.
Note: When the clutch vanes (3) are plumb, the body of the clutch (1) is 1/16"to1/8"(1.5to 3 mm) out of plumb.
2. Add or remove shims (5) between the door and the door hanger (6) as required. SeeFigure47.
Note: Place the shim only halfway under the door and bend the protruding end down by hammering it flat.
Figure47ShimDoorandDoorHanger
Figure46CheckClutch
48 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 11
The coupler ramp (1) determines when the coupler latch (2) starts to open as the car door is closing. SeeFigures48and49.
Followtheprocedurebelowtoadjustthecouplerramponlyifthefollowingconditionsoccur.
1. If the coupler latch (2) DOES NOT open:
a) The coupler latch (2) cannot open because the landing door is already closed and the latch is driving against the fixed door drive roller.
b) Move the coupler ramp (1) in the door open direction.
2. IfthelandingdoorISNOTlockedandthecardoor is closed:
a) Thelandingdoorlatchdoesnotlockbecauseoftheclosingforce,windordirtinthesill.
b) The clutch requires a minimum of 23 lbs. of closing force to operate. The closing force must not exceed 30 lbs. per A17.1.
c) Move the coupler ramp (1) in the door close direction.
Figure48AdjustCouplerRamp
Figure49CouplerLatch
49Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 12
Followtheprocedurebelowtocheckthecardooropenbumpersetting.
1. Move the car doors to the fully open position.
2. Makesurethedoorbumper(1)istouchingthedoorstop(2).SeeFigure50.
3. If the door bumper (1) IS NOT touching the door stop (2) with the car doors completely open:
a) Loosenthesocketheadcapscrew(3).
b Move the door bumper (1) until it is against the door stop (2).
c) Tightenthesocketheadcapscrew(3).
Figure50CheckDoorBumperSetting
50 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 13
Followtheprocedurebelowtoadjustthespacingofthelandingdoor drive rollers.
1. Makesuretheclutchopensandclosesproperly.
2. Makesurethereis3/8"(10mm)clearancebetweenthefrontofthedoordriverollers(5and6)andtheedgeofplatform.SeeFigure51.
3. If adjustment is necessary, loosen the set screws in the door drive rollers and adjust the door drive rollers in or out as required. Tighten the set screws after adjusting.
4. SeeFigure52.Verifytheoutside-to-outsidedimensionofthedoordriverollers(5and6)is3-3/4"(95mm).Verifythattherollersarecenteredwiththeclutch.
5. If necessary, adjust the spacing of the rollers:
a. Movethecaruntilthecarheaderisbelowthedoordriverollers(5and6).
b. Loosenthetwopositioningscrews(7)tosetthedoordriveroller(5).Loosenthepositioningscrew(8)tosetthedoordriveroller(6).
c. Set the distance from the outside of door drive roller (5) to the outside of door drive roller (6)to3-3/4"(95mm).
d. Tighten all positioning screws when done.
e. Ensure the rollers are centered with the clutch.
Figure52SpacingofDoorDriveRollers
4-3/4 in.
Figure51RollerClearance
51Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 14
Followtheprocedurebelowtorun"LearnTrip".
1. On the Supra board, set DIP switch S1-1 to the ON position to place the door operator in Service Testmode.SeeFigure53.
2. VerifyDIPswitchesS1-2,S1-3,S1-4,S1-5,andS1-6areintheOFFposition.
3. VerifyDIPswitchesS1-7andS1-8areinONtheposition.
4. Press and release the LEARNbuttonontheSupraboardafterpowerup.SeeFigure54.TheSTATUSLED(amber)willilluminate.Ensurethedoorisfullyclosed.
5. TheTestDrivebuttonshaveanOPENdirectionbuttonandaCLOSEdirectionbutton.UsetheCLOSEdirectionbuttontodrivethedoorintheCLOSEdirectionuntilthedoorsarecompletelyclosed. The OPEN direction button may be used to drive the door closed the first time. When the doorsarecompletelyclosed,theREFSWLEDisilluminated.
6. If themotorwas rotating in thewrongdirection, the rotation iselectronicallycorrectedandreset.LearnTripisre-energized.
7. Push and hold the OPEN direction button to open the doors. Run the doors open until the door stops against the door stop.
8. PushandholdtheCLOSEdirectionbuttontoclosethedoors.Runthedoorscloseduntilthedoorstops against the bumper.
9. CyclethedoorsfullyopenandcloseduntiltheSTATUSLEDturnsoff.TheSTATUSLEDshouldturnoffafternomorethanfivecycles(normally2-1/2cycles).
10. Check/setthedoorclosingforcetobetween23and30pounds(102-135Newtons).RefertoStep 15.
11. SetDIPswitchS1-1totheOFFpositionforNormalOperationmode.
Note: Whenopeningthedoorfromthefullyclosedposition,manuallyreleasethemechanicallockingdevice (if away from the landing doors).
Service Test Mode
Figure53DIPSwitchSettings
52 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Figure54RunningLearnTrip
Learn Button
53Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Step 15
Followtheprocedurebelowtosetthedoorclosingforce.
•Minimumdoorclosingforceis23pounds(102Newtons).
•Maximumdoorclosingforceis30pounds(135Newtons).
1. Tocheckthedoorclosingforce,physicallystallthedooratthemidpointintheclosingdirection.Then, place the rubber end of a pressure gauge (1) on the edge of the power-driven car door (3). SeeFigure55.
2. Back-offthegaugeuntilthedoorstartsmoving.Readthepoundsofforce(2)onthegaugeandrecord the results.
3. Allow the doors to open and close several times.
4. Physicallystallthedoorsagainintheclosingdirectionandre-checkthedoorclosingforcewiththe pressure gauge.
Figure55CheckingDoorClosingForce
54 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
5. If the door closing force requires adjustment, remove the door operator board cover and use the CloseForcepotentiometerontheSupraboardtoadjusttheclosingforce.SeeFigure56.
• TurntheCloseForcepotentiometerCLOCKWISEtoINCREASEthedoorclosingforce.
• TurntheCloseForcepotentiometerCOUNTER-CLOCKWISEtoDECREASEthedoorclosingforce.
6. Afteradjustingtheforce,ALWAYSchecktheclutchforfullactuationintheCLOSEpositionwithsignalapplied.Iftheclutchisnotactuatingfully,increasetheCLOSEforceslightlyandchecktheforce again with the gauge.
Caution: Failuretocheckforfullclutchactuationcouldresultinseriousdamagetothecardoorequipment.
Figure56AdjustPotentiometerClosingForceonSupraBoard
3. SUPRA BOARD
The following section provides information about the door operator board (Supra board).
3.1 POWER SUPPLy
The door operator drive has automatic line voltage detection. During power up, it detects the applied voltage and switches the transformer to the appropriate winding.
Therecommendedfuseis6Afor115-125VAC.
The line-in supply is connected either to the D1 flying leads or directly to the Phoenix connector (X19) at the bottom left of the Supra board.
3.2 SAfETy CIRCUIT
The door contact wires are pre-wired to a Molex plug (D2), a male connector with flying leads provided for controller connection.
Safetycontactratings:Min.5VDC-Max.250VAC.
3.3 SERVICE TEST MODE
When DIP switch S1-1 on the Supra board is in the ON position, the door operates in Service Test mode. OPENandCLOSEcommandsfromthecontrolleraredisabled.
The doors can be driven using the Test Drive buttons located on top of the door operator near the motor (7). The Test Drive buttons are disabled when DIPswitchS1-1isintheOFFposition.
DIPswitchS1-1mustbeintheOFFpositionwhileoperatingthecarinnormalorinspectionmode.This allows the controller to sendaCLOSEcommand todrive thedoor closedandexpand theclutch.
55Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
3.4 LEDS
At power-up, check for illuminated LEDs on the board (Figure 57).TheWDOG LED should not beilluminatedatpower-up.AdescriptionoftheLEDsisprovidedinthetablesbelow.
LED LED Inputs illuminated when:
I1 Input 1 is connected to COM (door OPEN command preset)
I2 Input 2 is connected to COM (door CLOSE command preset)
I3 Input 3 is connected to COM (door nudging - close direction only)
I4 Input 4 is connected to COM (high speed; DIP switch S1-6 must be off )
I5 Input 5 is connected to COM (emergency open with battery power only)
IPD Input Passenger-Protection Device (light curtain)
LED LED Outputs illuminated when:
O1 Output 1 relay is operating (open end; fully open door position)
O2 Output 2 relay is operating (close end; fully closed door position)
O3 Output 3 relay is operating (re-open; not used)
O4 Output 4 relay is operating (position; door opens wider than set trigger)
LED Miscellaneous LEDs illuminated when:
POWER The power supply is switched on
WDOG The microcontroller does not work
STATE On: During start-up and learning Flashes: If an error is detected Off: Normal operation
REFSW The door is in the close end switch area
VOLTAGE SEL 120V 120 VAC supply voltage selected
Figure57SupraBoardLEDs
56 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
57Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
When the car doors are fully closed and the unit is ready to operate, the following LEDs will beilluminated:
l POWER,REFSW,VOLTAGESEL120VandO2.
Whenthedoorsareopening,thefollowingLEDswillbeilluminated:
l POWER,VOLTAGESEL120VandI1.
Whenthedoorsarefullyopen,thefollowingLEDswillbeilluminated:
l POWER,VOLTAGESEL120VandO1.
Whenthedoorsareclosing,thefollowingLEDswillbeilluminated:
l POWER,VOLTAGESEL120VandI2.
3.5 DIP SWITChES
EnsurethatDIPswitchesS1-7andS1-8areON.SeeFigure58.
Note: WhenDIPswitchS1-1issettoON(seeFigure58),thisindicatesServiceTestmode.MakesureDIPswitchS1-1isreturnedtotheOFFpositionfornormaloperation.
Figure58SupraBoardDIPSwitches
Service Test Mode
58 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Figure59SupraBoardInterfaceWiring
3.6 INTERfACE WIRINg
Figure59providesaninterfacewiringdiagramfortheSupraboard.
A-1 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
appendix a
DOOR OPERATOR DIAGNOSTICS
ANDTROUBLESHOOTING
A-2 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
DOOR OPERATOR DIAgNOSTICS
SITUATION CAUSE DETERMINE CAUSE CORRECTIONBeforeperforming any diagnostics
Power failure. Verifythemainelevator disconnect is on.Makesurethe115VACfuseisprotecting power to the door operator and other functions, and is not open.
Turn on the main elevator disconnect or replace the open fuse.
CheckthatLEDsarelit according to the supply voltage.
Turn on the main elevator disconnect or replace the open fuse.
CheckfuseF1onthedoor operator board.
Replace the fuse once. If the fuse burns out again, replace the door control board.
Checkthepowersupply wiring.
Connect the plugs properly.
Door operator does not start learning drive
Closing force limit is too low.
Turn the ‘close force’ potentiometer slightly to increase the force.
Encoder, motor or bad contact in reference.
Replace the faulty component.
Door does not move at all
Motor is not running onOPEN/CLOSEcommand.
Verifythemotorwires are connected (plugX4).Verifythe control panel is giving an OPEN or CLOSEcommand(LEDI1,LEDI2).
Connect the unplugged wires.
Motor temperature is too high..
TheSTATELEDflashes (except during start-up).
Letthemotorcooldown.Ifthemotorgetstoohotagain,lookformechanicalobstructionsandremovethem.
ChecktheSTATELED.Checkforhigh friction when the door is moved manually.
Switch the operator power off and then on. Replace the boardiftheSTATELEDstillflashes.
Door is not moving
Doorisstuckmechanically.
Open the door with the emergency door keyandmovethedoor manually.
Adjust the door mechanics.
Verifydoorcontrolboard is receiving OPEN/CLOSEcommands and verify reference switch signal.
ViewLEDsI1andI2forOPEN/CLOSE.ViewtheREFSWLED.
A-3 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
DOOR OPERATOR DIAgNOSTICS
SITUATION CAUSE DETERMINE CAUSE CORRECTIONDoor does not open
Door operator board does not receive an OPEN command.
VerifytheOPENcommandLEDI1islitwhen an active OPEN command is present (low).
CLOSEcommand(LEDI2)isnotactive(low).CLOSEcommand overrides an OPEN command.Landingdoorlockisjammed.
Freethelandinglock.
Door does not close
Door operator board does not receive CLOSEcommand.
VerifytheCLOSEcommandLEDI2islit when an active CLOSEcommandispresent (low).
Closing force may be too low (or friction is too high).
Turnthe‘closeforce’potentiometerslightlyclockwisetoincrease the force.
A-4 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
DOOR OPERATOR TROUBLEShOOTINg
1. The learn cycle is invoked when power is cycled to the door operator.
Thisisanormalcondition.Itisusedtoinvokenudgingonthefirstcycleafterapoweroutagetoprotectpassengersfrombeingstruckbythedooratfullforcewhenpowerisrestored.
AlthoughtheSTATELEDstaysilluminatedforfivecyclesonly,thefirstcycleisoperatedatnudgespeed.
2. The test drive switch is inoperable.
CheckforilluminationoftheServiceDriveLED.
IftheServiceDriveLEDisnotilluminated,checkforilluminationoftheExt24+LED.
IftheExt24+LEDisnotilluminated:
l Checkthewiring.
l Tighten the terminals.
l Checkthesourceoftheexternal24VDCwithameter.
IftheExt24+LEDisilluminated:
l Checkthewiringtothetestdriveswitch.ItshouldbeconnectedattheGNDandServDrive(H3)terminals.
l Check for 115 or 220VAC at terminal X-19. If the voltage is present at terminal X-19,perform all of the tests in the power test document.
3. The door moves in the wrong direction when using the test buttons on initial startup and after power is cycled.
This is a normal condition. The door operator is re-learning the hand based on the torque and the reference switch position. The problem is corrected after the first cycle.
4. The door operator causes Ext. 24 VDC to overload and blow the fuse in the controller.
Withthedooroperatorpoweroff,useametertocheckforcontinuitybetweenExt.24+andGND.Ifcontinuityisfoundand/orterminalsarereadasashort,replacetheboard.Notethattheboard will not be covered under warranty as this indicates that a higher than recommended voltagehasbeenappliedtothe24VDCcircuit.
Beforeapplyingpowertotheboard,checkthepeakvoltagethatisappliedtoExt.24+.Thevoltageshouldbe24volts+/–2volts.Ifthevoltageisnotinrange,replacethe24VDCpowersupply.
A-5 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
5. The STATE LED fails to extinguish after five cycles.
The unit requires five complete cycles from the fully open to fully closed position. If the unit is halfwayopenandthefirsthalfcycleisintheclosedirection,itmaytakeadditionalcyclesforthe unit to find the fully open position.
This condition usually only occurs when using the test drive switch. Hold the Open/Closebuttondownuntilthedooroperatorreachesthefullyopenand/orfullyclosedposition.
6. The STATE LED fails to extinguish regardless of the number of cycles.
CheckforilluminationoftheREFSWLEDwhentheunitisinthefullyclosedposition.
IftheREFSWLEDisnotilluminated:
l Verifythatthemagnetisontheclutch.
l Checkthepositionofthemagnetatthefullyclosedposition.Itshouldbedirectlybelowor halfway past the switch.
l The pendant should rest against the close bumper when in the fully closed position.
l The gap between the magnet and the reference switch should be 1.5 to 3 mm.
IftheREFSWLEDisilluminated:
l Checkforobstructionskeepingtheunitfromreachingthefullyopenposition.
l Checkforalooseencodermagnetonthemotor.(Note:Toremovetheencoderhousing,the drive belt will have to be loosened using the idler pulley and then the motor will have to be removed.)
7. The REfSW LED is illuminated when closing but turns off when fully closed.
Checktheclosebumperposition. Iftheclosebumperis loose,thereferenceswitchmagnetcouldmovepastthereferenceswitchcausingtheLEDtoextinguishwhenthedoorsarefullyclosed.
8. The unit makes a rumbling sound when learning and nudging.
This is a normal condition caused by pulse width modulated power that is applied to the door operator motor. This type of power creates high torque at low RPM allowing the door operator to overcome small obstacles that may be lodged in the sill.
9. The unit becomes erratic and sometimes goes into the learn cycle under normal operating conditions.
Checkthe115/220VACandExt.24VDCpowersources.Eitherofthesepowersourcesdroppingout can cause this condition.
A-6 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
10. The unit does not respond to commands from the controller.
Checkformechanicalbinding.
Checkforindicationsofextremeheatatthetopoftheboard(MOSFETsandtwogreenwire-wound resistors). If extreme heat or damage is indicated, replace the board. Note that the board will not be covered under warranty as this indicates improper setup of the equipment.
Checktheoperationoftherestrictorbeforeoperatingtheunit.Iftherestrictorisnotpicking,checkfortheoutsidetooutsidedimensionof3¾”onthedoordriverollers.
CheckforilluminationoftheLEDsthatcorrespondtothe command issued.
IftheOPENandCLOSELEDs(I1andI2)arerespondingtocontrollercommands:
l ChecktheServiceDriveLED.
l IftheServiceDriveLEDisilluminated, turn the Service Drive switch to the “Run” position and retry the controller commands.
l If theServiceDrive LED isnot illuminated, turn theServiceDrive switch to the“Test”position and move the operator using the service buttons located on top of the operator.
l Iftheunitfailstooperateintheservicedrivecondition,checkallconnectionsbetweenthe motor and the board.
l If the unit will not operate with the service buttons and all connections have been checked,removetheopen,close,nudge,closelimitandopenlimitwiringandretrytheservice drive buttons.
l If the unit still fails to operate, replace the board and retest.
11. The car and hall doors are out of sync when closing and re-opening.
Checkfortheoutsidetooutsidedimensionof3¾”onthedoordriverollers.
Checkforpropercouplingoftheclutchwiththedoordriverollers.Forexample,thereshouldbe½”clearancebetweentheclutchvanesandthelandingdoorpickuprollers.
A-7 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
LED fUNCTIONALITy
When the car doors are fully closed and the unit is ready to operate, the following LEDs will beilluminated:
l POWER,REFSW,VOLTAGESEL120VandO2.
Whenthedoorsareopening,thefollowingLEDswillbeilluminated:l POWER,VOLTAGESEL120VandI1.
Whenthedoorsarefullyopen,thefollowingLEDswillbeilluminated:l POWER,VOLTAGESEL120VandO1.
Whenthedoorsareclosing,thefollowingLEDswillbeilluminated:l POWER,VOLTAGESEL120VandI2.
POWER SUPPLy TEST
CheckformainpowerinputvoltageatterminalX-19ontheboard.Thisvoltagecanbe115,220,or385VACsinglephase.
l Ifpowerdoesnotexist,checkthewiringandfusesinthecontroller.
l Ifpowerexists,checkfortransformerpowerinputatterminalX-9.
l If power does not exist at X-9, the voltage detection circuit is bad (replace the board).
l IfpowerexistsatX-9,checkfortransformerpoweroutputatterminalX-6.
l IfpowerdoesnotexistatX-6,replacethetransformer.
l IfpowerexistsatX-6,checkfor24VDCatterminalX-5.
l If24VDCdoesnotexist,thepowersupplycircuitisbad(replacetheboard).
l If24VDCexists,re-seatallconnectors.
l If theLEDsdonot illuminate, the internalpowersupplyoutput isdefective (replace theboard).
B-1Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
appendix B
TWO-SPEED DOORS PARTSLIST
B-2 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
3
5
9
11
12
29
25
6
7
10
14
15
16
17
22
24
27
28
LANDINg DOOR ASSEMBLy
3
5
7
6
910
27
1112
2812
12
12
22
22
3
HoistwaySide LandingSide
ExplodedView
B-3Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
Item # Savaria PN Description qty
-252054 LandingDoorAssembly,RightHandAssembly 1
252086 LandingDoorAssembly,LeftHandAssembly 1
3 252057 Strut 2
5 252067-P StrikeJamb 1
6252071-P HeadJamb,RightHand 1
252093-P HeadJamb,LeftHand 1
7 252089-P PassJamb 1
9 252066 Sight Guard 1
10 252078 Header 1
11301367 DoorHangerAssembly,RightHand,Wittur 1
301368 DoorHangerAssembly,LeftHand,Wittur 1
12 250335 Angle Ties 4
14 102197 HHCS3/8-16x1 -
15 102191 LockWasher,3/8 -
16 102188 FlatWasher,3/8USS -
17 102186 HexNut,3/8-16 -
19 103639 Anchor,HollowWall,1/4”x3” 12
20 103640 Anchor,HexSLV3/8”x3”Masonry 12
22252104-P SlowDoorPanel,36”x80”,RightHand 2
252123-P SlowDoorPanel,36”x80”,LeftHand 2
24 100737 RubberBumper,RB-45 2
25 105713 Screw,SmallPhillips,#14x3/4Znc -
27 252228 Bracket,HeadJambtoHeader 1
28 252472 Sill Assembly 1
29 103685 Nut,Weld3/8-16DblTab -
LANDINg DOOR ASSEMBLy
B-4 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1
45
2
3
6
Item # Savaria PN Description
-301367 LandingDoorHangerAssembly,RightHand
301368 LandingDoorHangerAssembly,LeftHand
1301258 DoorLockAssembly,Right
301259 DoorLockAssembly,Left
2FastHangerPlateAssembly,Right
301392 FastHangerPlateAssembly,Left
3SlowHangerPlateAssembly,Right
SlowHangerPlateAssembly,Left
4 301267 Synchronization Cable
5 Door Contact Wire
6 301271 Closer Reel
LANDINGDOORHANGERASSEMBLY(RIGHTHANDSHOWN)
B-5Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1
3
4
56
2
LANDINGDOORFASTHANGERPLATE(RIGHTHANDSHOWN)
Item # Savaria PN Description
1 301261 HangerRoller,Left
2 301265 Counter Roller
3 301260 HangerRoller,Right
4 Buffer
5301363 LockRoller(LeftHandAssembly)
301362 LockRoller(RightHandAssembly)
6 Door Contact Plug
7 301266 LockRollerONLY
B-6 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1
2
3
LANDINGDOORSLOWHANGERPLATE
Item # Savaria PN Description
1 301260 HangerRoller
2 301265 Counter Roller
3 301264 Synchronization Roller
B-7Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
CARDOORHANGERASSEMBLY
1 2 5
7
8
4
3
6
Item # Savaria PN Description
1 CarDoorHangerAssembly
2FastHangerPlateAssembly,Left
FastHangerPlateAssembly,Right
3SlowHangerPlateAssembly,Left
SlowHangerPlateAssembly,Right
4 Synchronization Rope
5
301272 LockClutchAssembly,Right
301273 LockClutchAssembly,Left
301292 Clutch Magnet Contact
6 EndStop,Left
End Stop, Right
7 Buffer
8
301274 Door Contact Assembly, Right
301275 DoorContactAssembly,Left
Contact
ContactBridge
NS 301471 CarRubberBumper
B-8 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
2
1
3
CARDOORFASTHANGERPLATE
Item # Savaria PN Description
1 301265 Counter Roller
2 301260 HangerRoller
3 SheaveBolt,M8x20
B-9Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1
2
3
4
CARDOORSLOWHANGERPLATE
Item # Savaria PN Description
1 301260 HangerRoller
2 301265 Counter Roller
3 301264 Synchronization Roller
4 SheaveBolt,M8x20
B-10 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
1
23
45
6
78
91011
DOOR OPERATOR ASSEMBLy
B-11Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
DOOR OPERATOR ASSEMBLy
Item # Savaria PN Description
-DoorOperatorAssembly,RightHand
DoorOperatorAssembly,LeftHand
1301276 Motor/GearboxAssembly,RightHand
301277 Motor/GearboxAssembly,LeftHand
2 301285 Encoder
3 301278 Transformer
4
ElectronicsBox(IncludingPlugs)
Spare Plug Set
301403 SupraControlBoard
5 301286 Magnetic Switch
6 301280 Diverting Pulley
7 BeltFixing
8 301282 ToothedBelt
9 301288 TestDriveButtons
10 301291 PushButtonCover(Rubber, Close Direction)
11 301290 PushButtonCover(Rubber, Open Direction)
NS 301287 Remote Switch Run/TestService
NS 301289 PushButtonSpacer
NS 301396 Operator Reference Switch
NS 301416 CoverforDoorOperatorControlBoard
NS 772328 Harness,COPtoOperator
NS 772329 InterfaceBoard
NS 772330 Harness,DuplineBoardtoInterfaceBoard
NS 772331 Harness,InterfaceBoardtoOperatorBoard
B-12 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
MISCELLANEOUS ITEMS
Item # Savaria PN Description
NS 301333 GibPackage
NS 301334 DoorKey
NS 301339 DoorFireRetainer
NS 301364 CouplerRamp,RightHand
NS 301365 CouplerRamp,LeftHand
NS 301385 EmergencyUnlockingDevice,RightHand
NS 301386 EmergencyUnlockingDevice,LeftHand
C-1 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
appendix C
IMPORTANT MEASUREMENTS
D-1 Two-Speed Doors Installation GuidePN 000597 (Rev. 12-m04-2010)
appendix d
KEYWAYTEMPLATE
TWO-SPEED DOORS
INSTALLATION AND SERVICE MANUAL
Part No. 000597
Copyright © 2009, 2010
Savaria CorporationElevators and Lifts107 Alfred kuehne Blvd.Brampton, ON L6T 4k3CanadaToll free: (800) 791-7999fax: (905) 791-2222