Upload
vasea
View
239
Download
0
Embed Size (px)
Citation preview
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 1/16
Tutorial 5: Revolves, Patterns, and Copies
Introduction
The Revolve option is useful for designing circular parts and features. Patterns and copies allow multiple instances of a feature tobe created with little effort. In this section, you will revolve a section around a centerline to create a pulley and a hole. You will alsocreate a pattern of holes and a copy of this pattern.
Creating a Revolved Part
1. Start Pro! "ildfire.#. $hoose %&ile' () %*ew' and name the new part %!+ample'.
3. Select the Revolve Tool icon from the tool bar at the right of the screen, as shown in &igure .1.
%&igure .1'
4. Select the S-etcher icon from the revolve tool bar on the dashboard.
5. Select the plane labeled &R*T and select the S-etch button in the Section menu.
6. Select %S-etch' () %Intent /anager' from the menu bar.
7. 0oom in so that you see the coordinates shown in &igure .#.
8. Select %ine' from the 2!/!TRY menu, and select %$enterline' from the I*! TYP! menu.
1
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 2/16
9. $lic- point 3 and point 4 shown in &igure .# to create a centerline.
10. Select %2eometry' from the I*! TYP! menu.
11. 5raw the section shown in &igure .# by clic-ing the endpoints with the left mouse button, and then clic-ing the middle mouse
button.
%&igure .#'
12. Select %Regenerate' from the S6!T$7!R menu.
13. 3dd the dimension shown at point 3 in &igure .8 by performing the following steps9
$lic- !dge1 with the left mouse button.
$lic- $enterline with the left mouse button.
$lic- !dge1 again with the left mouse button.
2
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 3/16
$lic- point 3 with the middle mouse button.
14. &ollow the same procedure to add the dimensions at points 4 and $. 15. &ollow the normal procedure for dimensioning to add the dimensions at points 5, !, &, 2, and 7.
16. Select %Regenerate'. You should now be able to see dimensions similar to those shown in &igure .8.
%&igure .8'
17. Select %Scale' from the /5 S6!T$7 menu.
18. Select the dimension at point 3.
19. Type : into the te+tbo+ and clic- the chec- mar-.
20. Select %Regenerate'. 3ll of the dimensions should scale.
21. Select %/od !ntity' from the /5 S6!T$7 menu.
3
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 4/16
##.$hange the dimension of 4 to 1::, $ to #::, 5 to 1#., ! to #, & to :, 2 to ;#., and 7 to <.
23. Select %Regenerate'. You should see the image shown in &igure .=.
%&igure .='
24. $hoose %5one' from /enu /anager. 25. $lic- the chec- button in the revolve tool bar.
26. Rotate the part to e+amine the modifications. You should see the image shown in &igure ..
4
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 5/16
%&igure .'
Creating a Sketched Hole by Revolving Section
1. Select the 7ole Tool icon from the tool bar at the right of the screen.
2. Select %S-etched' for the shape of the hole in the hole tool bar on the dashboard.
3. Select the S-etcher icon, as shown in &igure .;.
5
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 6/16
%&igure .;'
4. Select %S-etch' () %Intent /anager' from the menu bar.
5. Select %ine' from the 2!/!TRY menu and %$enterline' from the I*! TYP! menu.
6. $lic- points 3 and 4 to draw a centerline as shown in &igure .<. 7. Select %2eometry' from the I*! TYP! menu and clic- points $, 5, !, &, 2, 7, $ to draw the section shown in &igure .<.
6
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 7/16
%&igure .<'
8. Select %Regenerate' from the S6!T$7!R menu. 9. 5imension the section as shown in &igure .>.
?sing the left mouse button, clic- !dge1, $enterline, and !dge1 again. $lic- point 3 with the middle mouse button.
?sing the left mouse button, clic- !dge#, $enterline, and !dge# again. $lic- point 4 with the middle mouse button.
3dd the dimensions at points $ and 5 using the normal method.
10. Select %Regenerate' from the S6!T$7!R menu.
7
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 8/16
11. /odify the dimensions to match those shown in &igure .>.
%&igure .>'
12. Select %Regenerate' and then %5one' from the S6!T$7!R menu. 13. Select the top surface of the pulley. 3n outline of a hole should be shown as in &igure .@.
8
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 9/16
%&igure .@'
14. $lic- on the Placement menu on the dashboard and select %Radial' for the hole placement dimensions, as shown in &igure .1:.
15. $lic- and drag one handle on the hole to the center a+is of the hole in the pulley. 5rag the other handle to the plane labeled &R*T
Ado not select the handle that changes the diameter of the holeB. You should see the image shown in &igure .1:.
9
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 10/16
%&igure .1:'
16. 5ouble clic- on the dimension at point 3 in &igure .1: and change it to <:.
17. 5ouble clic- on the dimension at point 4 and change it to : degrees.
18. $lic- the chec- button and rotate the pulley to e+amine the hole. You should see the image shown in &igure .11.
10
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 11/16
%&igure .11' %&igure .1#'
Creating Patterns and Copies
1. Select the hole that was just created and select the Pattern Tool icon fro the tool !ar at the ri"ht of the screen.#. 5ouble clic- on the dimension that was shown at point 4 in &igure .1:. $hange the value from : to ;:, as shown in &igure .18.
3. $hange the number of features to ;, as in &igure .18. This will ma-e a pattern of ; holes located ;: degrees apart.
11
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 12/16
%&igure .18'
4. #lic$ the chec$ !utton. %ou should see the ia"e shown in &i"ure 5.14.
12
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 13/16
%&igure .1='
. To create a plane to mirror the holes, select the 5atum Plane icon from the tool bar at the right of the screen.
6. To define references' select the (lane la!eled T)P.
7. &ro the *+T,- P+/ enu' enter 37.5 into the )ffset Translation tet!o' and clic$ the ) !utton. This will (ut a datu (lane inthe center of the (ulle' as shown in &i"ure 5.15.
13
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 14/16
%&igure .1'
8. Select %!dit' () %&eature perations' from the menu bar. /enu /anager will pop up.
9. Select %$opy' from the &!3T menu.
10. Select %/irror' from the $PY &!3T menu. 11. Select %5one' from the $PY &!3T menu.
12. Select the Pattern A7oleB branch of the model tree at the left of the screen, and select %5one' from the S!!$T &!3T menu.
13. Select the datum plane that was Cust created, and select %5one' from the $PY menu. There should now be holes on both side of
the pulley, as shown in &igure .1;.
14
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 15/16
%&igure .1;'
14. Select %&ile' () %Save' from menu bar to save the part.
15. Test the information you have learned in this tutorial by completing Problem .
15
7/21/2019 Tutorial 5.doc
http://slidepdf.com/reader/full/tutorial-5doc-56d96e0289948 16/16
16