Upload
xmacaba
View
433
Download
25
Tags:
Embed Size (px)
DESCRIPTION
Tubing and Casing Thread Inspection 2014
Citation preview
THREAD GAUGING TECHNIQUES
API Tubing and Casing Threads
2014 Gagemaker, LP
Connection Thread Styles
API Tubing and Casing Tapered Threads
API Tubing and Casing Tapered Threads
Pin (External)
Coupling (Internal)
2014 Gagemaker, LP
EUE External Upset Tubing
NUE Non-Upset Tubing
BTC Buttress Casing
API Connection Names
API Tubing and Casing Tapered Threads
STC Short Thread Casing
LTC Long Thread Casing
Datum
2014 Gagemaker, LP
Purpose: Join two pieces of pipe together to produce a gas tight seal
API Specification 5B covers all Tubing and Casing dimensions
There are two types of pipe sizes
Tubing sizes: 1 4
Casing sizes: 4 20
There are two cone angles or tapers
All 8-round threads are Taper Per Foot (TPF)
Buttress sizes 4- 13 are TPF
Buttress sizes 16- 20 are 1 TPF
API Tubing and Casing Tapered Threads
What are Tubing & Casing Threads
2014 Gagemaker, LP
There are no lock washers or jam nuts on tapered threads to lock them together
The pin and box tapered threads interfere and allow them to form a seal when torqued together as the flanks of the threads compress against each other.
However, a clearance remains between the crests and roots of the threads, resulting in a helical leak path
Thread compounds or pipe dope plug up this helical path to produce a seal under high pressures
API Tubing and Casing Tapered Threads
How Threads Lock Up and Seal
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
8R Thread Form
2014 Gagemaker, LP
Datum
Pin Threads
API Tubing and Casing Tapered Threads
2014 Gagemaker, LP
Unlike straight threads where the pitch diameter is the same along the axis, a tapered thread changes in diameter along its axis.
The Datum Plane is a starting point or reference location on a part. All diameters are dimensioned at a distance from this location. Example L1, L2 & L4. Locate these on your TDWIN TAPER drawing.
Also, it is referred to as the face or end of pipe.
API Tubing and Casing Tapered Threads
What is a Datum Plane?
Please see the following pages for illustrations.
2014 Gagemaker, LP
Datum
API Tubing and Casing Tapered Threads
Datum Plane on a Pin
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
Datum Planes on a Coupling Datum A Datum B
2014 Gagemaker, LP
Request a product drawing on the threads.
Verify which thread form is required.
Request the threading insert called out on the drawing.
Request a gage Set-Up Sheet.
List all the gage serial # used to inspect the part.
Verify the ball contacts are the right size.
Set your gages to a zero value on a standard.
Now thread the part and start the inspection.
API Tubing and Casing Tapered Threads
What is the first step?
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
External Inspection
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
TDWIN TAPER Drawing- 7 LTC Pin
2014 Gagemaker, LP
Set the LG-5002 on Setting Standard* and zero the dial. After locking the bezel clamp, always double check your zero setting. Now, measure the part and compare the standard to the machined lead.
*Every different TPF requires a different lead setting standard.
Thread Lead Inspection with an LG-5002
API Tubing and Casing Tapered Threads
API Tubing and Casing Tapered Threads
The LG-5002 is used the same way on the part as on the standard. Place the fixed ball contact in the first full depth thread. Move the fixed ball back one thread and check again. Record your measurement.
Thread Lead Inspection with an LG-5002
Thread Height Inspection with a TH-3002
Set the TH-3002 on Setting Standard and tilt the base back and forth to obtain the lowest reading. After locking the bezel clamp, always double-check you zero setting. Now, measure the part and compare the standard to the machined thread groove.
API Tubing and Casing Tapered Threads
8 Round = .072125 10 Round = .05560 Buttress TPF = .0620 Buttress 1TPF = .0620
Thread Heights:
API Tubing and Casing Tapered Threads
Thread Height Inspection with a TH-3002
The TH-3002 is used the same way on the part as on the standard. Measure only within the perfect thread length. (On your thread drawing, this length dimension is called L2) Align the base parallel to the thread axis and tilt the base back and forth to obtain the lowest reading. Record your measurement.
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
Zero the dial on the first thread. Do not lock the bezel clamp! Note the radial location of the gage to the part or chuck. Move the gage up the taper 1 (8 R = 8 threads, Buttress = 5 threads). Place your index finger on top of the indicator stem to hold the ball contact into the thread groove.
Pin Taper Inspection with an ET-7000
2014 Gagemaker, LP
Pin Taper Inspection with an ET-7000
API Tubing and Casing Tapered Threads
After moving back 1 up the taper double check your radial position of the gage to the part or chuck. Failure to stay in the same radial position will induce errors caused by the thread helical path. If the gage rotated, the ball contacts will move up or down the taper. You are checking the change in diameter about a radial location or plane. On a 8R TPF connection, every 45 rotation of the gage = .00097 change in diameter.
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
MRP-2001 is set to a connection size by the use of A & B Rod Standards. The rod standards position the gage to measure the Crest Cone diameter at a known location from the datum plane or face. B standard sets the distance off the face. Hold light pressure between the shoe and wear pad and tighten both black knobs. A standard sets the crest cone diameter. Sweep the standard until the lowest indicator reading is obtained and zero the dial. Double- check the zero after locking the bezel clamp.
Pin PD Inspection with the MRP-2001 (Crest Cone Diameter Inspection)
B Standard
A Standard
2014 Gagemaker, LP
Pin PD Inspection with the MRP-2001 (Crest Cone Diameter Inspection)
API Tubing and Casing Tapered Threads
*Can preset with MIC TRAC
The MRP Shoe makes contact with the crest cone within the L2 perfect length. Gagemaker calculated the crest cone diameter from the Spec 5Bs pitch diameter. The shoe swivels so the taper tolerance will not effect the diameter reading. Using a shave gage the distance from the crest cone to the pitch diameter can be measured. As the threading insert wears the pitch diameter plane moves closer to the crest cone. The connection makes up on the thread flanks and not the crest cone.
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
Pin PD Inspection with the MRP-2001 (Crest Cone Diameter Inspection)
While holding the gage against the part face, sweep left & right to find the largest indicator value. Then, rotate the gage 90 and repeat. If the indicator value changes, this indicates Ovality or out of roundness. Take multiple readings around the part to find the largest and smallest values. Write these High and Low values down on your inspection report.
2014 Gagemaker, LP
Largest and smallest indicator readings provide the data for calculating Average Cone Diameter and Thread Ovality. They both use the same data but calculate the readings in different ways.
LARGEREADING
SMALLREADING
(Largest Diameter + Smallest Diameter) = Diameter 2 Largest Diameter - Smallest Diameter = Ovality
Largest Diameter
Smallest Diameter Ovality
+.005 -.010 .015
Largest Diameter
Smallest Diameter
Averaged Diameter
+.005 -.010 -.0025
Ovality Average Cone Diameter
Largest Diameter
Smallest Diameter Ovality
-.005 -.010 .005 Largest
Diameter Smallest Diameter Ovality
-.015 +.001 .016
Largest Diameter
Smallest Diameter
Averaged Diameter
-.005 -.010 -.0075 Largest
Diameter Smallest Diameter
Averaged Diameter
-.015 +.001 -.007
Ovality is how egg or out of round it is. Ovality is the amount of out-of-roundness in a piece of pipe or a coupling. Determining ovality requires locating the largest and the smallest diameter readings on the part and subtracting the smallest reading from the largest reading. Ovality readings are always positive (no sign attached).
What do you do with the high and low indicator values?
Average Cone Diameter is the size, it would be, if it were round. Determining the round diameter of a connector requires locating the largest and the smallest diameter readings on the part and taking the average of the two readings, as shown in the following formula:
API Tubing and Casing Tapered Threads
2014 Gagemaker, LP
LARGEREADING
SMALLREADING
Largest Diameter
Smallest Diameter
Averaged Diameter
+.005 -.010 -.0025
Largest Diameter
Smallest Diameter
Averaged Diameter
+.005 -.005 .000
Average Cone Diameter is the distance across the face of the pipe or coupling. Determining the round diameter of a connector requires locating the largest and the smallest diameter readings on the part and taking the average of these two readings.
API Tubing and Casing Tapered Threads
Average Cone Diameter
2014 Gagemaker, LP
LARGEREADING
SMALLREADING
Largest Diameter
Smallest Diameter
Total Ovality
+.005 -.010 .015
Largest Diameter
Smallest Diameter
Total Ovality
+.005 -.005 .010
Ovality is the amount of out-of-roundness in a piece of pipe or a coupling. Determining ovality requires locating the largest and the smallest diameter readings on the part and adding the smallest reading to the largest reading, as shown in the following formula. Ovality readings are always positive (no sign attached).
API Tubing and Casing Tapered Threads
Ovality
2014 Gagemaker, LP
Pin Thread Form Inspection
TP-8R Profile inspecting a pin thread. Always check the first starting thread.
When deburring the thread with a flapper wheel, burrs can be rolled into the thread groove. This will cause gauling when the connections are made up on the rig.
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
Pin Length Inspection
L2 L4
Always keep the scale parallel to the pipe axis. A digital depth gage can be used in place of a scale.
L2=Perfect thread length. Crest of thread must have a full radius top. L4=Last scratch length.
2014 Gagemaker, LP
Coupling Inspection
2014 Gagemaker, LP
Coupling Threads
API Tubing and Casing Tapered Threads
Datum A Datum B
2014 Gagemaker, LP
Request a product drawing on the threads. Verify which thread form is required. Request the threading insert called out on the drawing. Request a gage Set-Up Sheet. List all the gage serial #s used to inspect the part. Verify the ball contacts are the right size. Set your gages to a zero value on a standard. Now, thread the part and start the inspection.
What is the first step?
API Tubing and Casing Tapered Threads
2014 Gagemaker, LP
API Tubing and Casing Tapered Threads
TDWIN TAPER Drawing 7 LTC Coupling
2014 Gagemaker, LP
Set the LG-5002 on Setting Standard* and zero the dial. After locking the bezel clamp, always double-check your zero setting. Now, measure the part and compare the standard to the machined lead.
*Every TPF connection requires a different lead setting standard. We will discuss setting standard design in the next class.
Coupling Thread Lead Inspection with an LG-5002
API Tubing and Casing Tapered Threads
2014 Gagemaker, LP
LG-5002 Inspecting Coupling
Coupling Thread Lead Inspection with an LG-5002
API Tubing and Casing Tapered Threads
The LG-5002 is used the same way on the part as on the standard. Place the fixed ball contact in the first full depth thread. Move the fixed ball back one thread and check again. Record your measurement.
2014 Gagemaker, LP
Coupling Thread Height Inspection with a TH-3006
API Tubing and Casing Tapered Threads
Set the TH-3006 on Setting Standard and tilt the standard back and forth to obtain the lowest reading. After locking the bezel clamp, always double-check your zero setting. Now, measure the part and compare the standard to the machined thread groove.
Thread Heights: 8 Round = .072125, Buttress = .0620
2014 Gagemaker, LP
Coupling Thread Height Inspection with a TH-3006
API Tubing and Casing Tapered Threads
The TH-3006 is used the same way on the part as on the standard. Align the gage parallel to the thread axis and lift up and down to obtain the lowest reading. Record your measurement.
2014 Gagemaker, LP
Coupling Taper Inspection with an IT-6000
Zeroed on Coupling
API Tubing and Casing Tapered Threads
Zero the dial on the first thread. Do not lock the bezel clamp!
Note the radial location of the gage to the part or chuck. (6 or 12 oclock is best.)
Move the gage down the taper 1 (8 threads for 8R or 5 threads for Buttress).
2014 Gagemaker, LP
Inspecting Coupling
Coupling Taper Inspection with an IT-6000
API Tubing and Casing Tapered Threads
Failure to stay in the same radial position will induce errors caused by the thread helical path. If the gage rotated, the ball contacts will move up or down the taper.
After moving 1 down the taper, double-check your radial position of the gage to the part or chuck.
You are checking the change in diameter about a radial location or plane.
2014 Gagemaker, LP
MRP-2002 is set to a connection size by the use of A & B Rod Standards. The rod standards position the gage to measure the Crest Cone diameter at a known location from the datum plane or face. B standard sets the distance off the face. Hold light pressure between the shoe and wear pad and tighten both black knobs. A standard sets the crest cone diameter. Sweep the standard until the lowest indicator reading is obtained and zero the dial. Double- check the zero after locking the bezel clamp.
Coupling PD Inspection with an MRP-2002 (Crest Cone Diameter Inspection)
API Tubing and Casing Tapered Threads
B Standard
A Standard
2014 Gagemaker, LP
Inspecting Coupling
Coupling PD Inspection with a MRP-2002 (Crest Cone Diameter Inspection)
While holding the gage against the part face, sweep left & right to find the largest indicator value. Then, rotate the gage 90 and repeat. If the indicator value changes, this indicates Ovality or out of roundness. Take multiple readings around the part to find the largest and smallest values. Write these values down on your inspection report.
API Tubing and Casing Tapered Threads
2014 Gagemaker, LP
LARGEREADING
SMALLREADING
Largest and smallest indicator readings provide the data for calculating Average Cone Diameter and Thread Ovality. They both use the same data but calculate the readings in different ways.
(Largest Diameter+Smallest Diameter) = Diameter 2 Largest Diameter - Smallest Diameter = Ovality
Largest Diameter
Smallest Diameter Ovality
+.005 -.010 .015
Largest Diameter
Smallest Diameter
Averaged Diameter
+.005 -.010 -.0025
Ovality Average Cone Diameter
Largest Diameter
Smallest Diameter Ovality
-.005 -.010 .005 Largest
Diameter Smallest Diameter Ovality
-.015 +.001 .016
Largest Diameter
Smallest Diameter
Averaged Diameter
-.005 -.010 -.0075 Largest
Diameter Smallest Diameter
Averaged Diameter
-.015 +.001 -.007
Ovality is how egg-shaped or out of round it is. Ovality is the amount of out-of-roundness in a piece of pipe or a coupling. Determining ovality requires locating the largest and the smallest diameter readings on the part and subtracting the smallest reading from the largest reading, as shown in the following formula. Ovality readings are always positive (no sign attached).
What do you do with the high and low indicator values?
Average Cone Diameter is the size, it would be, if it were round. Determining the round diameter of a connector requires locating the largest and the smallest diameter readings on the part and taking the average of the two readings, as shown in the following formula:
API Tubing and Casing Tapered Threads
2014 Gagemaker, LP
LARGEREADING
SMALLREADING
Largest Diameter
Smallest Diameter
Averaged Diameter
+.005 -.010 -.0025
Largest Diameter
Smallest Diameter
Averaged Diameter
+.005 -.005 .000
Average Cone Diameter is the distance across the face of the pipe or coupling. Determining the round diameter of a connector requires locating the largest and the smallest diameter readings on the part and taking the average of these two readings.
API Tubing and Casing Tapered Threads
Average Cone Diameter
2014 Gagemaker, LP
LARGEREADING
SMALLREADING
Largest Diameter
Smallest Diameter
Total Ovality
+.005 -.010 .015
Largest Diameter
Smallest Diameter
Total Ovality
+.005 -.005 .010
Ovality is the amount of out-of-roundness in a piece of pipe or a coupling. Determining ovality requires locating the largest and the smallest diameter readings on the part and adding the smallest reading to the largest reading. Ovality readings are always positive (no sign attached).
API Tubing and Casing Tapered Threads
Ovality
2014 Gagemaker, LP
Coupling Thread Form Inspection
TP-8R Profile inspecting a pin thread. Always check the first starting thread.
When deburring the thread with a flapper wheel, burrs can be rolled into the thread groove. This will cause gauling when the connections are made up on the rig.
2014 Gagemaker, LP
Coupling Length Inspection
API Tubing and Casing Tapered Threads
Coupling Length (NL)
NL/2
Q Q is measured from the coupling face to the start of the 35 chamfer.
Always keep the scale parallel to the coupling axis.
NL/2 = the coupling length. NL = Length of coupling.
Slide Number 1Slide Number 2Slide Number 3Slide Number 4Slide Number 5Slide Number 6Slide Number 7Slide Number 8Slide Number 9Slide Number 10Slide Number 11Slide Number 12Slide Number 13Slide Number 14Slide Number 15Slide Number 16Slide Number 17Slide Number 18Slide Number 19Slide Number 20Slide Number 21Slide Number 22Slide Number 23Slide Number 24Slide Number 25Slide Number 26Slide Number 27Slide Number 28Slide Number 29Slide Number 30Slide Number 31Slide Number 32Slide Number 33Slide Number 34Slide Number 35Slide Number 36Slide Number 37Slide Number 38Slide Number 39Slide Number 40Slide Number 41Slide Number 42Slide Number 43Slide Number 44