Tritex Brochure

Linear and Rotary Electric Actuation Without the oil and air of fl uid power Without the amplifi er, cables and panel space of a servo system

2ThreeTechnologies One ActuatorExlars Tritex Series actuators combine three technologies to deliver for the fi rst time a truly simple and low-cost electric alternative for fl uid power actua-tors and costly servo systems. Tritex actuators represent an all-electric actuator solution for moving and positioning mechanical devices in a large variety of commercial, industrial or military grade applications. Tritex actuators eliminate the

Tritex Actuator

ConventionalRotary Servo System

need for pneumatic and hydraulic cylinders while improving posi-tion performance, reducing cycle times and eliminating the main-tenance associated with fl uid power devices.

Ball screw mechanisms, or sepa-rately mounted gear reducers are also a thing of the past. Rotary- to-linear converters or mechani-cal reducers necessary to move the load are embedded into the Tritex design.

Less is MoreThe Tritex Series of electric actuators combine a brushless motor, servo amplifi er and posi-tion controller in a single

industrial grade enclosure. This eliminates both the external servo amplifi er and the expen-sive and failure prone cables associated with a typical servo system. Servo system com-ponent selection, design and installation are completely eliminated. Trouble shooting and debugging of individual components; gear reducers, rotary-to-linear converter mech-anisms and the complex wiring layout typical of such a system are gone. Moreover, the panel space for a separately mounted amplifi er and installation of that amplifi er are no longer neces-sary.

to run at a preset velocity until a switch input is received or a pre-programmed torque level is produced against a load. Alterna- tively, the rotary

Rotary Applications Tritex rotary motors and gear-motors provide high response and precise control of a rotatable shaft similar to that found in any electric motor. The differ-ence is that withTritex you can program (via your PC) the rotational speed and position of the output shaft inresponse to external com-mands. For example, the motor can be commanded to rotate at a controlled velocity and precisely stop at a pre-proprogrammed position. You can also program the unit

3ERVO'EAR2EDUCER)NSIDE/PTIONAL

!MPLIFIER

-OTOR

3ERVO'EAR2EDUCER

3ERVO-OTOR

#OUPLING

0OWER #OMMAND

0OWER

#OMMAND

23

3ERVO!MPLIFIER

23 &EEDBACK 07-0OWER

Tritex can be set up to follow an analog signal, either voltage or current, representing your choice of torque, velocity, or position.

Signals for initiating the prepro-grammed velocity and position commands come from optically isolated inputs or directly via the Modbus serial communica-tion channel provided on each Tritex unit. Likewise, isolated output commands of the sta-tus and events allow precise coordination with your system controls or machine operator.

Optional Internal GearReducer If the application requiresgreater torque and less speed than available with the baseunit, the Tritex is availablewith an integral servo grade planetary gear reducer. Gear ratios of 4:1 to 100:1 allow thepower of Tritex to be applied over a broad range of torque requirements.

3Compare a similar size ball screw to Exlars planetary roller screw design and see many more contact points on the roller screw. This results in up to 15 times the load-carrying capacity of ball screws and improved stiffness.

The difference is in the roller screws design for transmittingforces. Multiple threaded heli-cal rollers are assembled in a planetary arrangement around a threaded shaft as seen below, which converts a motors rotary motion into linear movement of the shaft or nut.

Roller Screw BasicsExlars patented, inverted roller screw is a mechanism for con-verting rotary torque into linear motion, in a similar manner to acme screws or ball screws. But, unlike those devices, roller screws can carry heavy loads for thousands of hours in the most

arduousconditions. Thismakes roller screws theideal choice for demanding, continuous-duty linear motion applications.

ConventionalLinear Servo System

Tritex Actuator

Linear ApplicationsTritex linear actuators employ Exlars patented, inverted roller screw mechanism for converting the rotational motion generated within the Tritex actuatorto the highly robust andlong-life linearmotionrequiredto solve applicationsthat previously required pneumatic or hydraulic cylinders. No additional mecha-nisms (such as acme or ball screws) are necessary to con-vert the actuators rotary power

to the linear motion required to move the load. The Tritex linear actuator contains the same control capability of the Tritex rotary actuator. (See previous page.)

3ERVO-OTOR

2OLLER3CREW

"ALL3CREW)NSIDE

#OUPLING-OTOR!MPLIFIER ,INEAR!CTUATOR

0OWER #OMMAND23

0OWER

#OMMAND

23

3ERVO!MPLIFIER

&EEDBACK 07-0OWER

In addition, the Tritex soft-ware allows you to create a sequence which causes the actuator, when commanded, to move forward while press-ing an object into position. You can establish a pre-pro-grammed force which triggers an event (such as stopping or retracting to another position) or it can maintain that force level until commanded other-wise. The sequence is ideal for assembly, test, fastening and pressing applications.

As with the rotary Tritex, the linear Tritex can be programmed to follow ananalog command signal, making it ideal for controlling valves and dampers in pro-cess control applications.

4Tritex Product Features 24 to 48 VDC Power Integrated brushless motor, amplifi er & controller Multiple termination and con-nector options

Rotary Tritex 60 and 90 mm frame sizes Up to 42 lbf-in (4.7 Nm) continuous and 84 lbf-in (9.4 Nm) peak torque IP65 sealing Integrated planetary gearingoption 4:1 to 100:1 ratios Up to 5000 rpm base motor speed

The Exlar AdvantageExlar has delivered thousands of roller screw based linear actuator solutions around the world in applications ranging from weld guns to controlling fuel or steam valves on turbine generators. Exlars linear actua-tors provide trouble-free, precise linear motion control for millions of cycles of operation.

Typical Applications Process Control Defense Aerospace Test Simulation Food Processing Industrial Automation Forestry Semi-conductor Remote Vehicles Medical Equipment Automotive Assembly Molding Die Casting Welding

Simulation

Process Control

Food Processing

Cut-to-Length in Sawmills

5 Alternate Mode; allows allows you to switch between 2 oper-ating modes.Selectable Output FunctionsEnabled Homed Ready (Enabled and Homed) Fault Warning Fault or Warning Ac-tive Move (1-4) in Progress Homing Jogging Jogging+ Jogging- Motion In Position At Home Position At Move (1-4) Position Stopped Holding In Current Limit In Current Fold back Above Rated Current Maintain a Preset Force Home

Analog Input: 0 to +10 VDCor 4-20mA, 12 bit resolution Force/torque velocity posi-tion

Analog Output: 4-20mA,11 bit resolution Force/torque velocity posi-tion

Serial Interface: RS485, Modbus RTU Programming controlling monitoring

Custom ProductsWhile Exlar delivers Tritexactuators off the shelf, Exlar prides itself in its ability to modify the products thereby fulfi lling your exact needs and assuring the success of your application.

Exlar also welcomes the op-portunity to work with you to develop custom software pages tailored to your applica-tion needs. Customer logos, specialty control pages and pre-confi gured setups are just some of the software tools that we can provide to make Tritex products a perfect fi t for your application.

Contact Exlar at (952) 368-3434 or [email protected] to discuss the details.

Linear Tritex 2 and 3 inch (51 and 76 mm)frame sizes 3 to 18 inch (75 to 455 mm) strokes available 0.1, 0.2, 0.4 and 0.5 inchlead (2.54, 5.08, 10.16 and 12.7 mm) planetary roller screws Up to 1250 lbf (5560 N) max continuous thrust capacity, 2270 lbf (10,000N) peak Up to 33 inches (838 mm) per second max linear velocity IP54 sealing standard, IP65 optional Multiple mounting options

Tritex Series OperationThe Tritex Series actuators can operate in one of fi ve different motion producing modes. These modes solvean endless variety of applica-tions in industrial automation, medical equipment, fasten-ing and joining, blow mold-ing, injection molding, testing, food processing, and more.

Programmed functions are stored in the Tritex non-vola-tile memory. An RS/485 serial interface allows control, pro-gramming and monitoring of all aspects of the motor or actua-tor as it performs your applica-tion.

Operating Modes1) Move To A Position (Or Switch)The Tritex Series actuators al-low you to execute your pro-grammed positions or distanc-es. You may also use a limit switch or other input device as the end condition of a move. This combination of index fl ex-ibility provides a simple solution for point-to-point indexing.

2) Move To A Preset Force Or Torque The Tritex Series allows you to terminate your move upon the achievement of a programmed torque or force. This is an ideal mode for pressing and clamping applications.

3) Position Propor- tional To An Analog Signal Ideal for process control solutions, the Tritex Series provides the functionality to position a control valve by following an analog input signal. This allows the Tritex Series to deliver precise valve control unachievable by other electric, hydraulic or pneumatic actuators.

4) Velocity Proportional to An Analog SignalTritex actuators offer you the capability to control velocity with an analog signal. This is par-ticularly useful with Tritex rotary actuators offering precise con-trol of the speed of any process or operation.

5) Force/Torque Proportional to Analog SignalPerfect for pressing and torqu-ing applications, you can control torque from an analog input.

Communications & I/ODigital I/O: 8 input, 4 output, 10-24 VDC, optically isolated

Selectable Input FunctionsEnable Initiate Move (1-4) Dedicated Position Jog+ Jog- Jog Fast Home Extend Switch Retract Switch Home Switch Teach Enable Teach Move (1-4) Stop Hold

6Tritex TSM Linear Actuator and Remote Amplifi er, Connectorized

Cable length 6 ft maximum

Tritex RSMRotary Motor andRemote Amplifi er with Internal Terminal Strips

High Heat Moves the electronics away from a hot environment 55o C environmental tempera-ture rating Allows the actuator to be mounted in the higher tempera-ture environment

Small Size Reduces the size of the actua-tor by making the electronics remote Compact electronics housing can be machine mounted up to 6 feet away

TRA500 Connectorization options include either connectors or internal terminals 24 - 48 VDC IP67 to be mounted on machine All the functionality of the integrated Tritex electronics

TRA500 REMOTE AMPLIFIER SPECIFICATIONS Input Voltage, Bus and Logic

24-48 Volts DC nominal, 20-60 Volts continuous operating range. Under-voltage trip 19V, over-voltage trip 85V

I/O Power Supply 24V nominal, 30V max, 12V minDigital Inputs 8 opto-isolated, 24V nominal 30V max, programmable func-

tionsDigital Outputs 4 opto-isolated 50 mA continuous, 24V nominal 30V max,

short circuit protected, programmable functionsAnalog Input 0-10 Volts or 0-20 mAmps, differential input 12 bit resolution,

programmable as position, velocity or torque commandAnalog Output 0-20 mAmps, 11 bit resolution, programmable functionsSerial Interface RS-485, Modbus RTU protocol, max baud rate 38.4kCommutation SInusoidal, 15kHz PWMFeedback Analog HallContinuous Output Current (Peak of Sine Amps)*

25o C Ambient 40o C Ambient 55o C AmbientStall Rated Stall Rated Stall Rated15 15 14 12 12 8.5

Peak Output Current (Peak of sine Amps)

20

Termination Options

Threaded ports with internal terminal strip, connectors or fl ying leads

Environmental IP67, Humidity: 10 to 95%, non-condensing

Remote Amplifi er OptionNormally the Tritex electronics are mounted directly within the actuators housing. Exlar also offers the convenience of the Tritex electronics in a remote IP67 rated enclosure for appli-cations where physical size ortemperature constraints dont allow the electronics to be mounted on the actuator. The TRA500 remote electronics work with Exlars TSM and RSM Series actuators.

*Actual output current may be reduced if the motor/actuator continuous and peak current ratings are lower

Cable length 6ft maximum

7Expert User InterfaceExpert, the Tritex user interface software, provides you with a simple way to select all aspects of confi guration and control required to set up and operate a Tritex actuator. Easy-to-use tabbed pages provide access to input all of the parameters necessary to successfully confi gure your motion applica-tion. Application fi les give you a convenient way to store and redistribute confi gurations amongst multiple computers, and Drive fi les allow the same confi guration to be distributed to multiple Tritex actuators. Motion setup, homing, teach mode, tuning parameters, jogging, I/O confi guration, and local control are all accom-plished with ease using Expert software.

Motion SetupWithin the Expert software, Exlar provides several system confi gurations for various applications.

You can confi gure move to position, move to switch, or move to force motion at the click of a button. The Tritex products offer absolute and incremental motion, as well as feed moves endng on a condi-tion such as a specifi c force being reached, or an input being triggered by a proximity switch. The Expert software gives you the fl exibility to format your units as you wish for your your application as shown below left.

These can serve as your confi gu-ration, or as a starting point for your confi guration. Alternatively, you can begin from scratch select-ing confi guration details specifi cto your application.

Easy selection of move condi-tions, distance, speed and acceleration are shown in the setup screen shown lower left.

Control PageThe Expert control page gives you the ability to operate orinitiate all motion func-tions from one single, simple screen. This screen provides you very easy system start up and testing without all the inconve- nience of machine wiring.

This page offers the capability to enable and disable the drive and perform fast and slow jogs. This gives you the ability to verify motion before needing any I/O wiring.

8 Homing The Tritex homing setup is simple to use. It allows you to home to an input, by using a proximity or limit switch, or allows homing to a specifi c force or torque. This type of homing is ideal for setting up applications that require motion ref- erenced to a hard stop, like the closed position of a valve, or the fi nal position of a press.

Teach Mode To provide the easiest motion set up possible, Tritex products offer Teach mode. In this mode, you can jog the actuator to the desired position, and activate an input, or click a button in the Expert software and the current position of the actuator becomes the defi ned distance or absolute position associated with a particular move command.

Confi guring I/O Confi guring I/O points to one of over 40 available input or output functions couldnt be easier. A pull down menu adjacent to each I/O point allows all I/O to be set up in minutes.

Inputs can be confi gured to be maintained, or momentary, depending on the application requirements.Input and output logic can also be inverted with a simple click.

Monitor PageAll input functions can be moni-tored and activated from the Expert Monitor Page, and all out-put functions can be monitored. These functions can be moni-tored and controlled, even if they are not programmed as the func-tion of any particular hardware input or output. Information on critical fault and status data is available as a separate page, or as a fi xed window on the bottom of each page of the software.

Valve SoftwareTritex actuators provide a perfect solution for your valve actuation needs. Small hysteri-sis and dead band, quick re-sponse to small signal changes and stable dynamic responses are all key parameters deliv-ered by Tritex actuators. Our valve software is simple to use, featuring a teach mode for foolproof confi guration. Included is a programmable valve cut off position feature that enables a fi rm valve seat on both new valves, or retrofi t-ted valves. Available in both rotary and linear versions, Tritex actuators can be mounted on any valve from any manufacturer.

9TLM20 Speed vs. Force Curves ,%!$INCHMM xn x{ { n x { { { {n x{ x { {{x n n x { { x{ n { n n x { n n n x

{ n x x x{ { n x { xn n x { x n{

&ORCELBF.

,%!$INCHMM

3PEEDINCHSECMMSEC

-AX3PEED 6$#

-AX3PEED 6$#

0EAK

#ONTINUOUS

INSECMMSECINSECMMSECINSECMMSEC

4,-WITH"3TATOR

,%!$INCHMM xn x{ n x x x x{ x{ x x { {{{n {n nx { {n n nn x x n n x x { n x x x xx { { nn x {n n n x x n xx x { n xx

{ x x x{ { n x x xn { n {{

&ORCELBF.

,%!$INCHMM

3PEEDINCHSECMMSEC

-AX3PEED 6$#

-AX3PEED 6$#

0EAK

#ONTINUOUS


4,-WITH"3TATOR

,%!$INCHMM xn x{ {n nx { {n n nn x x n n x x { n{ x x x xx { { nn x {n n n x x n xx x n n xx

{ xx x { x{ xx n { xn xx { { x

&ORCELBF.

,%!$INCHMM

3PEEDINCHSECMMSEC

-AX3PEED 6$#

-AX3PEED 6$#

0EAK

#ONTINUOUS


4,-WITH"3TATOR

10

TSM20 Speed vs. Force Curves (Requires TRA500 Remote Amplifi er)

LEAD inch (mm) 0.4 0.2 0.1

(10.16) (5.08) (2.54) 150 300 600 (667) (1,334) (2,669) 125 250 500 (556) (1,112) (2,224) 100 200 400 (445) (890) (1,779) 75 150 300 (334) (667) (1,334) 50 100 200 (222) (445) (890) 25 50 100

(111) (222) (445)

0 0 0

0.00 2 4 6 8.33 0.1 0.00 (51) (102) (152) (212) (2.54) 0.00 4 8 12 16.7 0.2 0.00 (102) (203) (305) (423) (5.08) 0.00 8 17 25 33.3 0.4 0.00 (203) (432) (635) (846) (10.16)

Forcelbf(N)

LEAD inch (mm)

Speed inch/sec (mm/sec)

TSM20 with 1B8-50 Stator

Max Speed @24 VDC

Max Speed @48 VDC Peak

Continuous 25C

Continuous 40C

Continuous 55C

in/secmm/sec

in/secmm/sec

in/secmm/sec

LEAD inch (mm) 0.4 0.2 0.1

(10.16) (5.08) (2.54) 200 400 800 (890) (1,779) (3,559) 175 350 700 (778) (1,557) (3,114) 150 300 600 (667) (1,334) (2,669) 125 250 500 (556) (1,112) (2,224) 100 200 400 (445) (890) (1,779) 75 150 300 (334) (667) (1,334) 50 100 200 (222) (445) (890) 25 50 100

(111) (222) (445)

0 0 0

0.00 1 3 4 5.67 0.1 0.00 (25) (76) (102) (144) (2.54) 0.00 3 5.50 8 11.34 0.2 0.00 (76) (140) (203) (288) (5.08) 0.00 5.50 11 17 22.68 0.4 0.00 (140) (279) (432) (576) (10.16)

Forcelbf(N)

LEAD inch (mm)



Max Speed @24 VDC

Max Speed @48 VDC

Peak

Continuous 25C

Continuous 40C

Continuous 55C

in/secmm/sec

in/secmm/sec

in/secmm/sec

LEAD inch (mm) 0.4 0.2 0.1

(10.16) (5.08) (2.54) 300 600 1,200 (1,334) (2,669) (5,338) 250 500 (1,000) (1,112) (2,224) (4,448) 200 400 (800) (890) (1,779) (3,559) 150 300 (600) (667) (1,334) (2,669) 100 200 (400) (445) (890) (1,779) 50 100 (200) (222) (445) (890)

0 0 0

0.00 1 2 3 4.17 0.1 0.00 (25) (51) (76) (105) (2.54) 0.00 2 4 6 8.34 0.2 0.00 (51) (102) (152) (212) (5.08) 0.00 4 8 13 16.68 0.4 0.00 (102) (203) (330) (424) (10.16)

Forcelbf(N)

LEAD inch (mm)



Max Speed @24 VDC


Continuous 25C

Continuous 40C

Continuous 55C

in/secmm/sec

in/secmm/sec

in/secmm/sec

11

TLM30 Speed vs. Force Curves

&ORCELBF.

,%!$INCHMM

3PEEDINCHSECMMSEC

,%!$INCHMM xn x{ x x x { xx { {{{n nn x x { x n { {{{n x x {{ {

nn x{ n {{ x{ { { {{ xn x n{n{ xn x x x x nx { nx n

0EAK

#ONTINUOUS


-AX3PEED 6$#

-AX3PEED 6$#

4,-WITH"3TATOR

,%!$INCHMM xn x{ { n xn x n { {{{n { n xx x{ { n { x n { n {{x n

n xn n n{xn x{ { { x{ {{ x x xn x x x x nx n x{ {

&ORCELBF.

,%!$INCHMM

3PEEDINCHSECMMSEC

4,-WITH"3TATOR

-AX3PEED 6$#

-AX3PEED 6$#

0EAK

#ONTINUOUS


&ORCELBF.

,%!$INCHMM

3PEEDINCHSECMMSEC

,%!$INCHMM xn x{ n { n n { xx n { {x { { xn x n { {{{n { n n xx x{ x n { x n { n {{x n

{ n {{ xx x{ n { { {{ n{ {{ { nnn xn x {x x nx nx x{ { x xx

4,-WITH"3TATOR

0EAK

#ONTINUOUS


-AX3PEED 6$#

-AX3PEED 6$#

12

TSM30 Speed vs. Force Curves (Requires TRA500 Remote Amplifi er) LEAD inch (mm)

0.5 0.2 0.1(12.7) (5.08) (2.54)

240 600 1200 (1,068) (2,669) (5,338) 200 500 1000 (890) (2,224) (4,448) 160 400 800 (712) (1,779) (3,559) 120 300 600 (534) (1,334) (2,669) 80 200 400 (356) (890) (1,779) 40 100 200

(178) (445) (890)

0 0 0

0.00 0.67 1.33 2.00 2.67 3.33 0.1 0.00 (17.02) (33.78) (50.8) (67.82) (84.58) (2.54) 0.00 1.34 2.66 4.00 5.34 6.66 0.2 0.00 (34.04) (67.56) (101.6) (135.6) (169.2) (5.08) 0.00 3.35 6.65 10.00 13.35 16.65 0.5 0.00 (85.09) (168.91) (254) (339.1) (422.9) (12.7)

Forcelbf(N)

LEAD inch (mm)



Max Speed @24 VDC


Continuous 25C

Continuous 40C

Continuous 55C

in/secmm/sec

in/secmm/sec

in/secmm/sec

LEAD inch (mm) 0.5 0.2 0.1

(12.7) (5.08) (2.54) 360 900 1,800 (1,601) (4,003) (8,007) 320 800 1,600 (1,423) (3,559) (7,117) 280 700 1,400 (1,246) (3,114) (6,228) 240 600 1,200 (1,068) (2,669) (5,338) 200 500 1,000 (890) (2,224) (4,448) 160 400 800 (712) (1,779) (3,559) 120 300 600 (534) (1,334) (2,669) 80 200 400 (356) (890) (1,779) 40 100 200

(178) (445) (890)

0 0 0

0.00 0.43 0.87 1.30 1.73 2.17 0.1 0.00 (10.92) (22.10) (33.02) (43.94) (55.12) (2.54) 0.00 .086 1.74 2.60 3.46 4.34 0.2 0.00 (21.84) (44.20) (66.04) (87.88) (110.23) (5.08) 0.00 2.15 4.35 6.50 8.65 10.85 0.5 0.00 (54.61) (110.49) (165.10) (219.71) (275.59) (12.7)

Forcelbf(N)

LEAD inch (mm)



Max Speed @24 VDC

Max Speed @48 VDC

Peak

Continuous 25C

Continuous 40C

Continuous 55C

in/secmm/sec

in/secmm/sec

in/secmm/sec

LEAD inch (mm) 0.5 0.2 0.1

(12.7) (5.08) (2.54) 500 1,250 2,500 (2,224) (5,560) (11,120) 400 1,000 2,000 (1,779) (4,448) (8,896) 300 750 1,500 (1,334) (3,336) (6,672) 200 500 1,000 (890) (2,224) (4,448) 100 250 500

(449) (1,112) (2,224)

0 0 0

0.00 0.33 0.67 1.00 1.33 1.67 0.1 0.00 (8.38) (17.02) (25.40) (33.78) (42.42) (2.54) 0.00 0.66 1.34 2.00 2.66 3.34 0.2 0.00 (16.76) (34.04) (50.80) (67.56) (84.84) (5.08) 0.00 1.65 3.35 5.00 6.65 8.35 0.5 0.00 (41.91) (85.09) (127.00) 168.91) (212.09) (12.7)

Forcelbf(N)

LEAD inch (mm)



Max Speed @24 VDC

Max Speed @48 VDC

Peak

Continuous 25C

Continuous 40C

Continuous 55C

in/secmm/sec

in/secmm/sec

in/secmm/sec

13

RTM060 Speed vs.Torque Curves

4ORQUELBFIN

n

n

{{x

x x x x 20-

24-WITH"3TATOR

-AX3PEED 6$#

-AX3PEED 6$#

0EAK

#ONTINUOUS

Torque lbf-in (Nm)20 (2.26)

18 (2.03)

16 (1.81)

14 (1.58)

12 (1.36)

10 (1.13)

8 (0.90)

6 (0.68)

4 (0.45)

2 (0.23)

0 0 625 1250 1875 2500 RPM

Peak

Continuous

Max Speed @24 VDC

Max Speed @48 VDC

RTM060 with 3B8-25 Stator

*For RTG gearmotors, multiply torque by your ratio and effi ciency. Divide speed by gear ratio.

Torque lbf-in (Nm) 16 (1.81)

14 (1.58)

12 (1.36)

10 (1.13)

8 (0.90)

6 (0.68)

4 (0.45)

2 (0.23)

0 0 850 1700 2550 3400 RPM

Peak

Continuous

Max Speed @24 VDC

Max Speed @48 VDC


14

RSM060 Speed vs.Torque Curves (Requires TRA500 Remote Amplifi er)

Torque lbf-in (Nm)

12.0(1.36)10.0(1.13)

8.0(0.90)

6.0(0.68)

4.0(0.45)

2.0(0.23)

0.0

0 1250 2500 3750 5000 RPM

RSM060 with 1B8-50 Stator

Max Speed @24 VDC


Continuous 25C

Continuous 40C

Continuous 55C

Torque lbf-in (Nm)

16.0(1.81)14.0(1.58)12.0(1.36)10.0(1.13)

8.0(0.90)

6.0(0.68)

4.0(0.45)

2.0(0.23)

0.0

0 850 1700 2550 3400 RPM


Max Speed @24 VDC

Max Speed @48 VDC

Peak

Continuous 25C

Continuous 40C

Continuous 55C

Torque lbf-in (Nm)

25.0(2.82)20.0

(2.26)15.0

(1.69)10.0

(1.13)5.0

(0.56)

0.0

0 625 1250 1875 2500 RPM


Max Speed @24 VDC

Max Speed @48 VDC

Peak

Continuous 25C

Continuous 40C

Continuous 55C

15

RTM090 Speed vs.Torque Curves


30 (3.39)

20 (2.26)

10 (1.13)

0 0 425 850 1275 1700 RPM


Max Speed @24 VDC


Continuous


60 (6.78)

40 (4.52)

20 (2.26)

0 0 175 350 525 700 RPM

Peak

Continuous

Max Speed @24 VDC

Max Speed @48 VDC


*For RTG gearmotors, multiply torque by your ratio and effi ciency. Divide speed by gear ratio.


45 (5.08)

30 (3.39)

15 (1.69)

0 0 250 500 750 1000 RPM


Peak

Continuous

Max Speed @24 VDC

Max Speed @48 VDC

16

RSM090 Speed vs.Torque Curves (Requires TRA500 Remote Amplifi er)

Torque lbf-in (Nm)

35.0(3.95)30.0

(3.39)25.0

(2.82)20.0

(2.26)15.0

(1.69)10.0

(1.13)5.0

(0.56)

0.0

0 425 850 1275 1700 RPM


Max Speed @24 VDC


Continuous 25C

Continuous 40C

Continuous 55C

Torquelbf-in (Nm)

60.0(6.78)50.0

(5.65)40.0

(4.52)30.0

(3.39)20.0

(2.26)10.0

(1.13)

0.0

0 250 500 750 1000 RPM


Max Speed @24 VDC


Continuous 25C

Continuous 40C

Continuous 55C

Torque lbf-in (Nm)

80.0(9.03)70.0

(7.90)60.0

(6.77)50.0

(5.65)40.0

(4.52)30.0

(3.39)20.0

(2.26)10.0

(1.13)

0.0

0 175 350 525 700RPM


Max Speed @24 VDC

Max Speed @48 VDC

Peak

Continuous 25C

Continuous 40C

Continuous 55C

17

TLM20 LINEAR ACTUATOR PERFORMANCE SPECIFICATIONSBacklash in (mm) .008 (.20)

Lead Accuracy in/ft (mm/300 mm) .001 (.025)

Maximum Radial Load lb (N) 15 (67)

Environmental Rating: Std IP54 / IP65 Optional

Stator 1 Stack 1B8-50 2 Stack 2B8-34 3 Stack 3B8-25

Lead RPM at 48 VDC* 5000 3400 2500

0.1Stall Force lbf (N) 239 (1063) 377 (1677) 503 (2237)

Max Speed in/sec (mm/sec) 8.33 (212) 5.66 (144) 4.17 (106)

0.2Stall Force lbf (N) 119 (529) 188 (836) 251 (1117)


0.4Stall Force lbf (N) 60 (267) 94 (418) 126 (560)

Max Speed in/sec (m/sec) 33.33 (848) 22.66 (575) 16.66 (424)

Power Supply Current Draw at Rated Power (48 V) Amps 10 10 10

Resolution 0.001 revolution x lead

Accuracy (not including backlash) +/- 0.005 revolution x lead

Stroke Length inch (mm) 3 (75) 6 (150) 10 (250) 12 (305)

Approximate Weight lb (kg) 7 (3.2) 8.5 (3.9) 10 (4.5) 11.5 (5.2)

Dynamic Load Rating lb (N) .1 inch lead 1568 (6970) .2 inch lead 1219 (5422) .4 inch lead 738 (3283)

Estimated Travel Life Travel life in millions of inches where C = Dynamic load rating (lbf), F = Cubic mean applied load (lbf) and S = Roller screws lead (inch). L10 = (C/F)3 x S =

*RPM @ 24 VDC = 1/2 of listed value

TLM20 and TSM20 Performance Specifi cations

TSM20 LINEAR ACTUATOR PERFORMANCE SPECIFICATIONS (Requires TRA500 Remote Amp)Backlash in (mm) .008 (.20)





RPM at 48 VDC* 5000 3400 2500

Lead Ambient Temp Degrees C 25 40 55 25 40 55 25 40 55

0.1Stall Force lbf

(N)295

(1312)262

(1165)227

(1010)460

(2046)411

(1828)355

(1579)575

(2558)514

(2286)445

(1979)


0.2Stall Force lbf

(N)148

(658)131

(583)113

(503)230

(1023)205

(912)177

(787)288

(1281)257

(1143)223

(992)


0.4Stall Force lbf

(N)74

(329)66

(294)57

(254)92

(409)82

(365)71

(316)115

(512)103

(458)89

(396)

Max Speed in/sec (m/sec) 33.33 (848) 22.66 (575) 16.66 (424)


Resolution 0.001 revolution x leadAccuracy (not includingbacklash) +/- 0.005 revolution x lead

Stroke Length inch (mm) 3 (75) 6 (150) 10 (250) 12 (305)

Approximate Weight lb (kg) 7 (3.2) 8.5 (3.9) 10 (4.5) 11.5 (5.2)


See TLM 20 chart above for Dynamic Load Rating and Estimated Travel Life values.

18

TLM30 LINEAR ACTUATOR PERFORMANCE SPECIFICATIONSBacklash in (mm) .008 (.20)





Lead RPM at 48 VDC* 2000 1300 1000

0.1Stall Force lbf (N) 585 (2606) 935 (4159) 1250 (5560)

Max Speed in/sec (mm/sec) 3.33 (84.6) 2.17 (55.1) 1.67 (42.4)

0.2Stall Force lbf (N) 293 (1303) 468 (2082) 625 (2780)


0.5Stall Force lbf (N) 117 (520) 187 (832) 250 (1112)

Max Speed in/sec (m/sec) 16.67 (423.4) 10.83 (275.1) 8.33 (211.6)




Stroke Length inch (mm) 3 (75) 6 (150) 10 (250) 12 (305) 18 (455)

Approximate Weight lb (kg) 10 (4.5) 12 (5.4) 19.5 (8.8) 21 (9.5) 25.5 (11.6)

Dynamic Load Rating lb (N) .1 inch lead 3310 (14724) .2 inch lead 3570 (15880) .5 inch lead 3016 (13416)

Estimated Travel Life Travel life in millions of inches where C = Dynamic load rating (lbf), F = Cubic mean applied load (lbf) and S = Roller screws lead (inch). L10 = (C/F)3 x S =*RPM @ 24 VDC = 1/2 of listed value

TLM30 and TSM30 Performance Specifi cations

TSM30 LINEAR ACTUATOR PERFORMANCE SPECIFICATIONS (Requries TRA500 Remote Amp)Backlash in (mm) .008 (.20)

Lead Accuracy in/ft .001 (.025)




RPM at 48 VDC* 2000 1300 1000

Lead Ambient Temp Degrees C 25 40 55 25 40 55 25 40 55

0.1Stall Force lbf

(N)756

(3362)686

(3051)608

(2704)1201

(5342)1091

(4853)968

(4306)1545

(6872)1404

(6245)1247

(5547)


0.2Stall Force lbf

(N)378

(1681)343

(1526)304

(1352)600

(2669)545

(2425)484

(2153)772

(3434)702

(3123)623

(2771)


0.5Stall Force lbf

(N)151

(672)137

(609)122

(543)240

(1068)218

(970)194

(862)309

(1375)281

(1250)249

(1108)

Max Speed in/sec (m/sec) 16.67 (423.4) 10.83 (275.1) 8.33 (211.6)

Power Supply Current Draw at Rated Power (48 V) Amps 15 12 10 15 12 10 15 12 10



Stroke Length inch (mm) 3 (75) 6 (150) 10 (250) 12 (305) 18 (455)

Approximate Weight lb (kg) 10 (4.5) 12 (5.4) 19.5 (8.8) 21 (9.5) 25.5 (11.6)


See TLM 30 chart above for Dynamic Load Rating and Estimated Travel Life values.

19

RTM060 ROTARY MOTOR TORQUE AND SPEED RATINGSFor output torque of RTG gearmotors, multiply by ratio and effi ciency. Please note maximum allowable output torques in the table top of page 20.


RPM at 48 VDC* 5000 3400 2500

Continuous Torque lbf-in (Nm) 4.7 (.53) 7.5 (.85) 10 (1.13)

Peak Torque lbf-in (Nm) 9.4 (1.06) 15 (1.69) 20 (2.26)


Resolution 0.001 revolution / ratio

Accuracy(not including backlash) +/- 0.005 revolution / ratio


RTM/RTG060 AND RSM/RSG060 INERTIA Stator 1 Stack 2 Stack 3 Stack

RTM/RSM Motor Armature Inertia (+/-5%) lb-in-sec2 (kg-cm2) 0.000237 (0.268) 0.000413 (0.466) 0.000589 (0.665)RTG/RSG Gearmotor Armature Inertia* lbf-in-sec2 (kg-cm2) 0.000226 (0.255) 0.000401 (0.453) 0.000576 (0.651)*Add armature inertia to gearing inertia for total RTM system inertia.

RTM/RTG060 AND RSM/RSG060 RADIAL LOAD AND BEARING LIFERPM 50 100 250 500 1000lbf (N) 195 (867) 155 (690) 114 (507) 90 (400) 72 (320)Side load ratings shown above are for 10,000 hour bearing life at 25 mm from motor face at given rpm.

RTM/RTG and RSM/RSG060 Performance Specifi cations

RSM/RSG060 ROTARY MOTOR TORQUE AND SPEED RATINGS (Requires Remote Amp)RSM and RSG Models require a TRA500 remote amplifi er

For output torque of RSG gearmotors, multiply by ratio and effi ciency. Please note maximum allowable output torques in the table top of page 20.


RPM at 48 VDC* 5000 3400 2500

Ambient Temp Degrees C 25 40 55 25 40 55 25 40 55

Continuous Torque lbf-in (Nm)5.9

(.66)5.2

(.59)4.5

(.51)9.2

(1.0)8.2

(.93)7.1

(.80)11.4

(1.29)10.2

(1.15)8.9

(1.01)

Peak Torque lbf-in (Nm) 9.4 (1.06) 15 (1.69) 20 (2.26)



Accuracy(not including backlash) +/- 0.005 revolution / ratio


20

RTG/RSG060 GEARMOTOR MECHANICAL RATINGSOutput Torque at Motor Speed for 10,000 Hour Life

Maximum Allowable Output Torque - Set

by User1000 RPM 3000 RPM 5000 RPM

Model Ratio lbf-in Nm lbf-in Nm lbf-in Nm lbf-in NmRTG/RSG060-004 4:1 603 (68.1) 144 (16.2) 104 (11.7) 88 (9.9)

RTG/RSG060-005 5:1 522 (58.9) 170 (19.2) 125 (14.1) 105 (11.9)RTG/RSG060-010 10:1 327 (36.9) 200 (22.6) 140 (15.8) 120 (13.6)RTG/RSG060-016 16:1 603 (68.1) 224 (25.3) 160 (18.1) 136 (15.4)RTG/RSG060-020 20:1 603 (68.1) 240 (27.1) 170 (19.2) 146 (16.5)RTG/RSG060-025 25:1 522 (58.9) 275 (31.1) 200 (22.6) 180 (20.3)RTG/RSG060-040 40:1 603 (68.1) 288 (32.5) 208 (23.5) 180 (20.3)RTG/RSG060-050 50:1 522 (58.9) 340 (38.4) 245 (27.7) 210 (23.7)RTG/RSG060-100 100:1 327 (36.9) 320 (36.1) 280 (31.6) 240 (27.1)

Two torque ratings for the RTG and RSG gearmotors are given in the table above. The left hand columns give the maximum (peak) allow-able output torque for the indicated ratios of each size gearmotor. This is not the rated output torque of the motor multiplied by the ratio of the reducer.

It is possible to select a confi guration of the motor selection and gear ratio such that the rated motor torque, multiplied by the gear ratio ex-ceeds these ratings. It is the responsibility of the user to ensure that the settings of the system do not allow these values to be exceeded.

The right hand columns give the output torque at the indicated speed which will result in 10,000 hour life (L10). The setup of the system will determine the actual output torque and speed.

RTG/RSG060 GEARING REFLECTED INERTIASingle Reduction Double Reduction

Gear Stages lbf-in-sec2 (kg-cm2) Gear Stages lbf-in-sec2 (kg-cm2)4:1 0.0000132 (0.0149) 16:1 0.0000121 (0.0137)5:1 0.0000087 (0.00984) 20:1, 25:1 0.0000080 (0.00906)

10:1 0.0000023 (0.00261) 40:1, 50:1, 100:1 0.0000021 (0.00242)

RTG/RSG060 Performance Specifi cations

RTG/RSG060 BACKLASH AND EFFICIENCYSingle Reduction Double Reduction

Backlash at 1% Rated Torque 10 Arc min 13 Arc minEffi ciency 91% 86%

RTM/RSM060 MOTOR AND RTG/RSG060 GEARMOTOR WEIGHTS (approx.)RTM/RSM060 Without

GearsRTG/RSG060 with 1

Stage GearingRTG/RSG060 with 2 Stage

Gearing1 Stack Stator lb (kg) 3.0 (1.4) 7.5 (3.4) 9.3 (4.2)2 Stack Stator lb (kg) 4.1 (1.9) 8.6 (3.9) 10.4 (4.7)3 Stack Stator lb (kg) 5.2 (2.4) 9.7 (4.4) 11.5 (5.2)

21

RTM/RTG and RSM/RSG090 Performance Specifi cationsRTM090 ROTARY MOTOR TORQUE AND SPEED RATINGS

For output torque of RTG gearmotors, multiply by ratio and effi ciency. Please note maximum allowable output torques in the table top of page 22.


RPM at 48 VDC* 1700 1000 700

Continuous Torque lbf-in (Nm) 19 (2.1) 29.3 (3.3) 45 (5.0)

Peak Torque lbf-in (Nm) 30 (3.4) 50 (5.6) 70 (7.9)

Power Supply Current Drawat Rated Power (48 V) Amps 12 10 10


Accuracy (not including backlash) +/- 0.005 revolution / ratio


RSM/RSG090 ROTARY MOTOR TORQUE AND SPEED RATINGS (Requires Remote Amp) RSM and RSG Models require a TRA500 remote amplifi er.

For output torque of RSG gearmotors, multiply by ratio and effi ciency. Please note maximum allowable output torques in the table top of page 22.


RPM at 48 VDC* 1700 1000 700

Ambient Temp Degrees C 25 40 55 25 40 55 25 40 55

Continuous Torque lbf-in (Nm)22.1(2.5)

20.1(2.3)

17.7(2.0)

37.2 (4.2)

33.8 (3.8)

30.0 (3.4)

50.9 (5.7)

46.4 (5.2)

41.5 (4.7)

Peak Torque lbf-in (Nm) 30 (3.4) 50 (5.6) 70 (7.9)

Power Supply Current Draw at Rated Power (48 V) Amps 15 12 10 15 12 10 15 12 10


Accuracy (not including backlash) +/- 0.005 revolution / ratio


RTM/RTG090 AND RSM/RSG090 INERTIA Stator 1 Stack 2 Stack 3 Stack

RTM/RSM Motor Armature Inertia (+/-5%) lb-in-sec2 (kg-cm2) 0.00054 (0.609) 0.00097 (1.09) 0.00140 (1.58)RTG/RSG Gearmotor Armature Inertia* lbf-in-sec2 (kg-cm2) 0.00114 (1.29) 0.00157 (1.77) 0.00200 (2.26)*Add armature inertia to gearing inertia for total RTM system inertia.

RTM/RTG090 AND RSM/RTG090 RADIAL LOAD AND BEARING LIFERTM/RTG090 AND RSM/RTG090 RADIAL LOAD AND BEARING LIFERPM 50 100 250 500 1000lbf (N) 389 (1730) 309 (1375) 227 (1010) 180 (801) 143 (636)Side load ratings shown above are for 10,000 hour bearing life at 25mm from motor face at given rpm.

22

RTM/RSM090 MOTOR AND RTG/RSG090 GEARMOTOR WEIGHTS (approx.)RTM/RSM090 Without

GearsRTG/RSG090 with 1 Stage Gearing

RTG/RSG090 with 2 Stage Gearing

1 Stack Stator lb (kg) 5.4 (2.5) 12.8 (5.8) 14.8 (6.7)2 Stack Stator lb (kg) 7.8 (3.5) 15.2 (6.9) 17.2 (7.8)3 Stack Stator lb (kg) 10.2 (4.6) 17.6 (7.9) 19.6 (8.9)

RTG/RSG090 Performance Specifi cations

RTG/RSG090 GEARING REFLECTED INERTIASingle Reduction Double Reduction

Gear Stages lbf-in-sec2 (kg-cm2) Gear Stages lbf-in-sec2 (kg-cm2)4:1 0.000154 (0.174) 16:1 0.000115 (0.130)5:1 0.000100 (0.113) 20:1, 25:1 0.0000756 (0.0854)

10:1 0.0000265 (0.0300) 40:1, 50:1, 100:1 0.0000203 (0.0230)

RTG/RSG090 GEARMOTOR MECHANICAL RATINGSOutput Torque at Motor Speed for 10,000 Hour Life

Maximum Allowable Output Torque - Set

by User1000 RPM 1500 RPM 2000 RPM

Model Ratio lbf-in Nm lbf-in Nm lbf-in Nm lbf-in NmRTG/RSG090-004 4:1 2078 234.8 600 (67.8) 552 (62.4) 504 (56.9)

RTG/RSG090-005 5:1 1798 203.1 775 (87.6) 714 (80.7) 652 (73.7)RTG/RSG090-010 10:1 1126 127.2 890 (100.6) 820 (92.7) 750 (84.7)RTG/RSG090-016 16:1 2078 234.8 912 (103.4) 830 (94.7) 763 (86.2)RTG/RSG090-020 20:1 2078 234.8 980 (110.7) 900 (101.7) 820 (92.6)RTG/RSG090-025 25:1 1798 203.1 1250 (141.2) 1150 (130) 1050 (118.6)RTG/RSG090-040 40:1 2078 234.8 1200 (135.6) 1107 (125) 1013 (114.4)RTG/RSG090-050 50:1 1798 203.1 1550 (169.4) 1434 (162) 1317 (148.8)RTG/RSG090-100 100:1 1126 127.2 1100 (124.3) 1100 (124.3) 1100 (124.3)Two torque ratings for the RTG and RSG gearmotors are given in the table above. The left hand columns give the maximum (peak) allow-able output torque for the indicated ratios of each size gearmotor. This is not the rated output torque of the motor multiplied by the ratio of the reducer.

It is possible to select a confi guration of the motor selection and gear ratio such that the rated motor torque, multiplied by the gear ratio ex-ceeds these ratings. It is the responsibility of the user to ensure that the settings of the system do not allow these values to be exceeded.

The right hand columns give the output torque at the indicated speed which will result in 10,000 hour life (L10). The setup of the system will determine the actual output torque and speed.

RTG/RSG090 BACKLASH AND EFFICIENCYSingle Reduction Double Reduction

Backlash at 1% Rated Torque 10 Arc min 13 Arc minEffi ciency 91% 86%

23

TLM20 Dimensions

24

TSM20 Dimensions (Requires TRA500 Remote Amplifi er)

1.00025.4

.256.4

Dim "B"

Dim "A"

.123.1

.7519.1

1.0025.4

1.500-.003+.000

38.1-0.080

.250- .001+.000

6.35-0.010

#10-24UNC-2A

1/4-20 UNC-2Bx .375 Deep(x4 SS, x8 DS)

x.250 Deep(Double SideMount Only)

2.2456.9

2.2456.9

1.1228.4

2.55 B.C.64.7

Single Side MountOn This Side

.43811.1

R.62515.9

1.00025.4

.502- .001+.000

12.8-0.030

.75019.1

Dim "D"3.75095.3

3.12579.4

.250 (4X)6.4

1.00025.4

1.75044.5 2.236

56.8

.1253.2

1.50038.1

.75019.1

5.115129.9

3.11579.1

1.00025.4

2.74069.6

2.24056.9

1.000.00125.40.03

1.50038.1

Dim "C"

Dim "A"

1.00025.4

TSM20 Double Side Mounts or Extended Tie Rod Mount

1. Three mounting styles shown 2. Shown view is standard side for single side mount. *If "M" (metric) tie rod option, thread = M5x0.8

TSM20 Side Trunnion Mount

TSM20 Rear Clevis Mount or Front Flange Mount

1. Two mounting styles shown. 2. With flange mount, dimension "A" is equivalent to the top two drawing views.Note: Add 1.784 Inches to Dims "A&D" if ordering an Electric Brake or Internal End of Travel Switches.

Dim 3 inch (mm) stroke 6 inch (mm) stroke 10 inch (mm) stroke 12 inch (mm) strokeA 7.775 (197.5) 10.775 (273.7) 14.775 (375.3) 16.775 (426.1)B 5.613 (142.6) 8.613 (218.8) 12.613 (320.4) 14.613 (371.2)C 3.000 (76.2) 6.000 (152.4) 10.000 (254.4) 12.000 (304.8)D 8.775 (222.9) 11.775 (299.1) 15.775 (400.7) 17.775 (451.5)

25

TLM30 Dimensions

26

TSM30 Dimensions (Requires TRA500 Remote Amplifi er)

27

RTM060 / RTG060 Dimensions

28

RSM060 / RSG060 Dimensions (Requries TRA500 Remote Amplifi er)

29

RTM090 / RTG090 Dimensions

30

RSM090 / RSG090 Dimensions (Requires TRA500 Remote Amplifi er)

31

TRA500 Remote Amplifi er and Rod End Attachment Dimensions

TRA500-I

TLM/TSM Rod Ends

Spherical Rod Eye

TRA500-N/G

32

Rod End Attachment Dimensions (continued)

33

Model TTUSB485The TTUSB485 is a USB (Univer-sal Serial Bus) port to 2 or 4 wire isolated RS-485/422 converter. The serial port side can be set up for an RS-422 or RS-485 network. USB bus supplies power so no separate power supply is needed.

Model TT232485The Model TT232485 is a feature packed RS232 to RS-422/485 9-pin converter. The driver uses automatic SD (send data) or TS (handshake) control, or can be confi gured as always enabled for use in RS-422 systems.

Model TTPS1048Model TTPS1048 unregulated 48 VDC, 10A power supply.

Model TTSR1Shunt regulator dissipates ex-cess kinetic or potential energy to prevent amplifi er over-voltage shut down.

TRITEX TLM SERIES ORDERING GUIDEAAABB-CCDD-E-FG-HHH-HH - (XX..XX - #####)AAA = Actuator Type G = Rod EndTLM = Tritex Linear Actuator M = Male US Standard Thread A = Male MetricBB = Actuator Frame Size F = Female US Standard B = Female Metric20 = 2 inch (50 mm) X = Special (please specify)30 = 3 inch (75 mm) HHH-HH = Motor StatorCC = Stroke Length TLM2003 = 3 inch (75 mm) 1B8-50 = 1 Stack, 5000 rpm at 48 VDC, 2500 rpm at 24 VDC06 = 6 inch (150 mm) 2B8-34 = 2 Stack, 3400 rpm at 48 VDC, 1700 rpm at 24 VDC10 = 10 inch (250 mm) 3B8-25 = 3 Stack, 2500 rpm at 48 VDC, 1250 rpm at 24 VDC (1)12 = 12 inch (305 mm) TLM3014 = 14 inch (355 mm) (TLM30 only) 1B8-20 = 1 Stack, 2000 rpm at 48 VDC, 1000 rpm at 24 VDC18 = 18 inch (455 mm) (TLM30 only) 2B8-13 = 2 Stack, 1300 rpm at 48 VDC, 650 rpm at 24 VDCDD = Lead (linear motion per screw revolution) 3B8-10 = 3 Stack, 1000 rpm at 48 VDC, 500 rpm at 24 VDC (1)01 = 0.1 inch (2.54 mm) X..XX = Travel and Housing Options (Multiple Possible)02 = 0.2 inch (5.08 mm) Travel Options04 = 0.4 inch (10.16 mm). (TLM20 only) AR = External Anti-rotate 05 = 0.5 inch (12.7 mm) (TLM30 only) PF = Preloaded Follower (2) E = Connections L1/2/3 = External LImit SwitchesI = Exlar Std M23 style connector RB = Rear BrakeBxx = Embedded leads, xx = length in feet, 3 ft std XT = Special Travel OptionsJxx = Emb. leads w/receptacle, std M23 style connector, xx = ft, 3 ft std

Housing OptionsP5 = IP65 sealed housing

X = Special (please specify) Special Motor OptionsF = Mounting XL = Special LubricationC = Rear Clevis D = Double Side Mount XM = Special Motor OptionE = Extended Tie Rod F = Front Flange ##### = Part Number Designator for SpecialsS = Side Mount T = Side Trunnion Optional 5 digit assigned PN to designate unique model numbersM = Metric Extended Tie Rod X = Special

(1) Not available on 3 inch stroke(2) The dynamic load rating of zero backlash, preloaded screws is 63% of the dynamic load rating of the std non-preloaded screws. The calcu-lated travel life of a preloaded screw will be 25% of the calculated travel life of the same size and lead of a non-preloaded screw.

Options/Accessories

Model TT485SPRS485 Communications split-ter. Use to daisy-chain multiple Tritex actuators.

34

TRITEX TSM SERIES ORDERING GUIDE (Also See TRA500 Next Page)AAABB-CCDD-E-FG-HHH-HH - (XX..XX - #####)AAA = Actuator Type G = Rod EndTSM = Tritex Linear Actuator Used with TRA500 Remote Amplifi er

M = Male US Standard Thread A = Male Metric

BB = Actuator Frame Size F = Female US Standard B = Female Metric20 = 2 inch (50 mm) X = Special (please specify)30 = 3 inch (75 mm) HHH-HH = Motor StatorCC = Stroke Length TSM2003 = 3 inch (75 mm) 1B8-50 = 1 Stack, 5000 rpm at 48 VDC, 2500 rpm at 24 VDC06 = 6 inch (150 mm) 2B8-34 = 2 Stack, 3400 rpm at 48 VDC, 1700 rpm at 24 VDC10 = 10 inch (250 mm) 3B8-25 = 3 Stack, 2500 rpm at 48 VDC, 1250 rpm at 24 VDC (1)12 = 12 inch (305 mm) TSM3014 = 14 inch (355 mm) (TSM30 only) 1B8-20 = 1 Stack, 2000 rpm at 48 VDC, 1000 rpm at 24 VDC18 = 18 inch (455 mm) (TSM30 only) 2B8-13 = 2 Stack, 1300 rpm at 48 VDC, 650 rpm at 24 VDCDD = Lead (linear motion per screw revolution) 3B8-10 = 3 Stack, 1000 rpm at 48 VDC, 500 rpm at 24 VDC (1)01 = 0.1 inch (2.54 mm) X..XX = Travel and Housing Options (Multiple Possible)02 = 0.2 inch (5.08 mm) Travel Options04 = 0.4 inch.(10.16 mm) (TSM20 only) AR = External Anti-rotate L1/2/3 = External Limit Switches05 = 0.5 inch (12.7 mm) (TSM30 only) PF = Preloaded Follower (2) RB = Rear BrakeE = Connections XT = Special Travel OptionsI = Exlar Std M23 style connector Housing OptionsJ3 = Emb. leads w/receptacle, std M23 style conn., 3 ft. J6 = Emb. leads w/receptacle, std M23 style conn., 6 ft.

P5 = IP65 sealed housingSpecial Motor Options

X = Special (please specify) XL = Special LubricationF = Mounting XM = Special Motor OptionC = Rear Clevis D = Double Side Mount ##### = Part Number Designator for Specials E = Extended Tie Rod F = Front Flange Optional 5 digit assigned PN to designate unique model numbersS = Side Mount T = Side Trunnion

TRITEX RTM/RTG SERIES ORDERING GUIDEAAABBB-CCC-D-E-FFF-FF- (XX...XX) - #####)AAA = Actuator Type E = Connector OptionsRTM = Tritex Rotary Motor I = Exlar Std M23 style connector RTG = Tritex Rotary Gearmotor Bxx = Embedded leads, xx = length in feet, 3 ft std BBB = Frame Size Jxx = Embedded leads w/recpt., M23 std, xx = length in ft, 3 ft std 060 = 60 mm X = Special (please specify)090 = 90 mm FFF-FF = Motor StatorsCCC = Gear Ratio RTM / RTG060Blank = RTM 1B8-50 = 1 Stack, 5000 rpm at 48 VDC, 2500 rpm at 24 VDCSingle Reduction Ratios Double Reduction Ratios 2B8-34 = 2 Stack, 3400 rpm at 48 VDC, 1700 rpm at 24 VDC004 = 4:1 016 = 16:1 020 = 20:1 3B8-25 = 3 Stack, 2500 rpm at 48 VDC, 1250 rpm at 24 VDC005 = 5:1 025 = 25:1 040 = 40:1 RTM / RTG090010 = 10:1 050 = 50:1 100 = 100:1 1B8-17 = 1 Stack, 1700 rpm at 48 VDC, 850 VDC at 24 VDCD = Shaft Type 2B8-10 = 2 Stack, 1000 rpm at 48 VDC, 500 VDC at 24 VDCK = Keyed 3B8-07 = 3 Stack, 700 rpm at 48 VDC, 350 VDC at 24 VDCR = Smooth/Round XX = Special OptionsX = Special Shaft XH = Special Housing Options XM = Special Motor Options

XL = Special Lubrication##### = Part Number Designator for SpecialsOptional 5 digit assigned PN to designate unique model number

(1) Not available on 3 inch stroke(2) The dynamic load rating of zero backlash, preloaded screws is 63% of the dynamic load rating of the std non-preloaded screws. The calcu-lated travel life of a preloaded screw will be 25% of the calculated travel life of the same size and lead of a non-preloaded screw.

35

TRITEX RSM/RSG SERIES ORDERING GUIDE (Also see TRA500 Below)AAABBB-CCC-D-E-FFF-FF- (XX...XX) - #####)AAA = Actuator Type E = Connector OptionsRSM = Tritex Rotary Motor Used with Remote Amplifi er I = Exlar Std M23 style connector RSG = Tritex Rotary Gearmotor Used with Remote Amp J3 or J6 = Embedded leads w/receptacle, M23, J3 = 3 ft, J6 = 6 ft BBB = Frame Size FFF-FF = Motor Stators060 = 60 mm RSM / RSG060090 = 90 mm 1B8-50 = 1 Stack, 5000 rpm at 48 VDC, 2500 rpm at 24 VDCCCC = Gear Ratio 2B8-34 = 2 Stack, 3400 rpm at 48 VDC, 1700 rpm at 24 VDCBlank = RSM 3B8-25 = 3 Stack, 2500 rpm at 48 VDC, 1250 rpm at 24 VDCSingle Reduction Ratios Double Reduction Ratios RSM / RSG090004 = 4:1 016 = 16:1 020 = 20:1 1B8-17 = 1 Stack, 1700 rpm at 48 VDC, 850 VDC at 24 VDC005 = 5:1 025 = 25:1 040 = 40:1 2B8-10 = 2 Stack, 1000 rpm at 48 VDC, 500 VDC at 24 VDC010 = 10:1 050 = 50:1 100 = 100:1 3B8-07 = 3 Stack, 700 rpm at 48 VDC, 350 VDC at 24 VDCD = Shaft Type XX = Special OptionsK = Keyed XH = Special Housing OptionsR = Smooth/Round XM = Special Motor OptionsX = Special Shaft XL = Special Lubrication

##### = Part Number Designator for Specials Optional 5 digit assigned PN to designate unique model number

TRITEX SERIES CABLES & ACCESSORIES Part NumberPower Cables, molded M23 style connector, 8 pin, xxx = Length in feet. Std lengths 15, 25, 50 feet CBL-TTIPC-SMI-xxxI/O Cables, molded M23 style connector, 19 pin, xxx = Length in feet. Std lengths 15, 25, 50 feet CBL-TTIOC-SMI-xxxCommunication Cable, PICO type connector, 4 pin, xxx = Length in feet. Std lengths 15, 25, 50 feet CBL-TTCOM-xxxCommunication Cable for use with TT485SP, xxx = Length in feet. Std lengths 15, 25, 50 feet CBL-TTDAS-xxxCable with connectors both ends from TRA to actuator, 3 or 6 feet CBL-TTUMB-00xUniversal Serial bus port to RS-485/422 converter TTUSB485RS-232 to RS-422/485 converter TT23248548 VDC, 10A power supply TTPS1048Shunt regulator TTSRIRS-485 Splitter TT485SP

TRITEX TRA500 REMOTE AMPLIFIER ORDERING GUIDEAAABBB-C-#####AAA = Amplifi er TypeAAA = TRA Remote Amplifi erBBB = Power500 = 500 WattsC = Connector OptionsN = 1/2 inch NPSM Threaded HolesG = PG Threaded HolesI = Exlar Standard M23 Style ConnectorBxx = Embedded Leads, 3 ft std,. xx = length in feetJxx = Embedded Leads w/M23 receptacle, 3 ft std., xx = length in feet##### = Part Number Designaor for SpecialsOptional 5 digit assigned PN to designate unique model number

Exlar Corporation, headquartered in sub-urban Minneapolis, Minnesota, serves a global customer base with an extensive standard product line and complete engi-neering support for custom actuator applications.

Exlar supports a large network of sales rep-resentatives worldwide. To fi nd your local dealer, visit our website at www.exlar.com or call us.

US HeadquartersExlar Corporation1470 Lake Drive WestChanhassen, MN 55317952-368-3434

Exlar Corporation1470 Lake Drive West

Chanhassen, MN 55317

PH: 952-368-3434FAX: 952-368-4877

2/2010 10K PN 44227

The 2010 Catalog includes full specifcations on Exlars GSX, GSM, EL, FT, and I Series linear actuators and SLM, SLG and ER Series rotary actuators.

Other product lines are also available from Exlar as seen in the brochures below.

Exlars Tritex II Series actuators are AC powered and offer additional and distinct features not available with its predecessor, theTritex Series actuators.

Ideal for industrial positioning or material handling applications, please see the Extrak brochure depicting Exlars line of rodless actuators.

Tritex IITM Line Voltage Linear and Rotary Electro-Mechanical Actuators

Europe Sales Offi ceExlar GmbHFrankfurter Str. 10765479 RaunheimGermany49 6142 17590-0

Documents

Tritex Brochure