Trinitron Integrated Digital Television - pro.sony

4-102-518-12(1)

KD-32NX200AUS

© 2004 Sony Corporation

Operating InstructionsBefore operating the TV, please read the ‘Safety Information’ section of thismanual. Retain this manual for future reference.

TrinitronIntegrated Digital Television

®

410251812

Thank you for choosing this FD Trinitron Integrated

Digital Television

Before operating the TV, please read this instructionmanual thoroughly and retain it for future reference.

All instructions in this manual refer to buttons on thesupplied remote control unless stated otherwise.

The model and serial numbers are located on the backof the TV. Record the serial number in the spaceprovided below. Refer to these numbers wheneveryou call your dealer regarding this product.

Model No. KD-32NX200AUS

Serial No. ______________

Please note: The information in this manual was correct at the time ofgoing to print. However, some minor changes may have been made latein the product’s development. All illustrations in this manual have beencreated during the product’s development and may differ slightly to thefinished product.

TRINITRON COLOUR TV 32NX200AUS

SER. No.

6000001

MANUFACTURED IN UKPRODUCT BY SONY CORPTOKYO / JAPAN

MODEL NO. KD-

220-240V 50/60Hz 154W

N50Serial No.

Table of Contents

Table of Contents 1

Table of Contents

Safety InformationSafety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Getting StartedChecking the supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Inserting batteries into the remote control . . . . . . . . . . . . . . . . . . . . . . 3Connecting an aerial and VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Switching on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Automatically tuning the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Switching between digital and analogue mode . . . . . . . . . . . . . . . . . . 5Adjusting the Brightness, Colour and Sharpness settings . . . . . . . . . . 6Adjusting the sound settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Basic OperationOverview of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Overview of the TV buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Everyday use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Digital Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Analogue Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Advanced OperationThe Channel Index menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14The Digital Electronic Programme Guide (EPG) . . . . . . . . . . . . . . . . . 15The Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17The Main menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Detail Set-up menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Using the TV menu system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Picture Adjustment menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Sound Adjustment menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Features menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Set Up menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Manual Set Up menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Manual Programme Preset menu . . . . . . . . . . . . . . . . . . . . . . . . . 24Further Programme Preset menu . . . . . . . . . . . . . . . . . . . . . . . . . 24

Connecting Other EquipmentOverview of the rear sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Overview of the front sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Connecting other equipment to the TV. . . . . . . . . . . . . . . . . . . . . . . . . 27

Connecting HD equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Viewing pictures from equipment connected to the rear sockets . . . . . 27Viewing pictures from equipment connected to the front sockets . . . . 27Remote control of other equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Programming the remote control. . . . . . . . . . . . . . . . . . . . . . . . . . 28Controlling a DVD player. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Controlling a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Additional InformationSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32How to lift the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

Safety Information

2 Safety Information

This set is to operate on a 220-240V ACsupply only. Take care not to connect toomany appliances to the same power socketas this could result in fire or electric shock.

For environmental and safety reasons, it isrecommended that the TV is not left ifstandby when unused. Disconnect from themains. However, some TVs may havefeatures which need the TV to be left instandby to work correctly. The instructionsin this manual will inform you if this applies.

Never push objects of any kind into the setas this could result in a fire or electric shock.Never spill liquid of any kind on the set. Ifany liquid or solid object does fall through,do not operate the TV. Have it checkedimmediately by qualified personnel.

Do not open the cabinet and the rear coverof the TV. Refer to qualified servicepersonnel only.

To prevent fire or shock hazard, do notexpose the TV to rain or moisture.

For your own safety, do not touch any partof the TV, power lead or aerial lead duringlightning storms.

Do not cover the ventilation openings of theTV. For ventilation, leave a space of at least10cm all around the set.

Never place the TV in hot, humid orexcessively dusty places. Do not install theTV where it may be exposed to mechanicalvibrations.

Clean the screen and cabinet with a soft,lightly dampened cloth. Do not use any typeof abrasive pad, alkaline cleaner, scouringpowder or solvent, such as alcohol orbenzine, or antistatic spray. As a safetyprecaution, unplug the TV before cleaning it.

Pull out the power lead by the plug. Do notpull on the power lead itself.

Take care not to place heavy objects on thepower lead as this could result in damage.We recommend you wind any excess leadaround the holders provided on the rear ofthe TV.

Unplug the power lead before moving theTV. Avoid uneven surfaces, quick steps orexcessive force. If the set has beendropped or damaged, have it checkedimmediately by qualified service personnel.

Do not cover the ventilation openings of theTV with items such as curtains ornewspapers etc.

Do not place any objects on the TV. Toprevent fire, keep inflammable objects ornaked lights (e.g. candles) away from the TV.

Place the TV on a secure stable stand. Neverattempt to move the TV and stand together -always move the TV and stand separately.Do not place the TV on its side or face up. Donot allow children to climb on to it.

Getting Started

Getting Started 3

Follow steps 1 - 8 to install the TV and view programmes

Check that you have the following items:

• Always observe the correct polarity when inserting batteries.• Please dispose of batteries in an environmentally friendly way.• Do not use old or different types of batteries together.• To avoid battery leakage and damage to the remote control, remove the

batteries if you are not going to use the remote for several days. If any liquid that has leaked from the batteries touches you, wash it away immediately with water.

Batteries

Checking the supplied accessories1

Inserting batteries into the remote control2

RF lead

Remote control

Scart lead

Scart adaptor

MADE IN INDONESIA FABRIQUÉ EN INDONÉSIEAAA LR03 AM4 1.5V

MADE IN INDONESIA FABRIQUÉ EN INDONÉSIE

AAA LR03 AM4 1.5V

2

1

Coin

3

5

4

DIGITAL/a

GUIDE

MODE

INDEX

Getting Started

4 Getting Started

1. Connect your aerial lead to the socket labelled DIGITAL on the rear ofthe TV.

2. Connect the supplied RF lead from the socket labelled on the rear ofthe TV to the socket labelled IN* on your VCR.

3. Connect an RF lead from the socket labelled OUT* on your VCR to thesocket labelled ANALOGUE on the rear of the TV.

4. Connect the supplied scart lead from the socket labelled i3/r3 on therear of the TV to the audio/video sockets labelled TV* on your VCR.

5. Insert a pre-recorded tape into the VCR and press the ‘PLAY’ button.This enables the TV to locate and store the video channel during the‘Automatically tuning the TV’ procedure.

Connecting an aerial only

1. Connect your aerial lead to the socket labelled DIGITAL on the rear ofthe TV.

2. Connect the supplied RF lead from the sockets labelled andANALOGUE on the rear of the TV.

z *Socket names may vary depending on make and model of VCR. Refer to yourVCR instruction manual for details.

Supplied RF lead

Rear of VCR

Supplied Scart lead

V/L/R connectors

Rear of TV

Connecting an aerial and VCR3

Y/U/V connectors

Getting Started

Getting Started 5

1. When you switch on the TV for the first time, the Sony logo is displayedon the TV screen, followed by the ‘Picture Rotation’ prompt. Sometimesthe Earth’s natural magnetism can cause the screen to look slanted.

a) If no correction is required, press B to select ‘Not Necessary’.

b) If some correction is required, press OK to select ‘Adjust now’.Press V or v to correct the slant. Press OK to confirm.

2. The ‘Autotune’ prompt appears on the TV screen. Press OK to select‘Yes’.

3. The ‘Region Set-up’ menu appears on the TV screen. Press V or v tohighlight your chosen region. Press OK to confirm.

The digital autotune display appears on screen and the TV starts tosearch for all the available digital channels. This may take some time,please be patient and do not press any buttons on the TV or remotecontrol.

If no digital or analogue channels are found, a message appears askingto confirm that the aerial is connected correctly. Check all the aerialconnections and press OK to start the automatic tuning process again.

When the digital autotune is complete, the analogue autotune starts tosearch for all the available analogue channels.

Once all available digital and analogue channels have been stored, theTV returns to normal operation, displaying the digital channel stored onchannel number 1. If no digital channels were found, the analoguechannel stored on channel number 1 is displayed.

The TV has now tunedin all the available channels

1. Press the DIGITAL/a button to switch between digital and analoguemode.

In digital mode, an information banner appears briefly on screen whenthe channel is changed.

In analogue mode, the channel number appears in green lettering whenthe channel is changed.

Switching between digital and analogue mode6

The ‘Autotune’ prompt.

Automatically tuning the TV5The ‘Picture Rotation’ prompt.

Do you want to startautomatic tuning?

Yes: OK No:

The ‘Region Set-up’ menu.Digital Set-up

Region Set-up

Press OK key to set your region

NEW SOUTH WALES / AUSTRALIAN CAPITAL TERRITORYVICTORIAQUEENSLANDSOUTH AUSTRALIAWESTERN AUSTRALIATASMANIA

Back

NORTHERN TERRITORY

If picture slants, pleaseadjust picture rotation.

Not Necessary:Adjust Now: OK

1. Connect the TV plug to your mains socket (220 - 240V AV, 50Hz)

2. Push in the On/Off button (labelled !) on the front of the TV.

z If the red standby mode indicator on the front of the TV is lit, press the TV I/1button on the remote control to switch on the set. Please be patient as the picturemay take a few moments to appear on the TV screen.

Switching on the TV4100HzDigtial Plus

On/Offbutton

Getting Started

6 Getting Started

This TV has four picture mode settings, ‘Live’, ‘Personal’, ‘Movie’ and ‘Game’. ‘Live’,‘Movie’ and ‘Game’ are preset modes and only the ‘Contrast’ setting can beadjusted. ‘Personal’ mode however, also allows you to adjust the ‘Brightness’,‘Colour’ and ‘Sharpness’ settings.

This TV has four sound settings, ‘Personal’, ‘Dolby V*, ‘Dynamic**’ and ‘Natural**’

1. Press the MENU button on the remote control to display the TV menusystem on the TV screen.

2. Press the b button to enter the ‘Picture Adjustment’ menu.

3. The ‘Picture Mode’ option is highlighted. Press the b button.

4. Press the V or v button to highlight ‘Live’, ‘Personal’, ‘Movie’ or ‘Game’.Press the OK button to confirm.

5. a) If you have selected ‘Live’, ‘Movie’ or ‘Game’:Go to step 6.

b) If you have selected ‘Personal’:You can now adjust the ‘Brightness’, ‘Colour’ and ‘Sharpness’ settings.(Sharpness is not adjustable in digital mode).

Press the V or v button to highlight ‘Brightness’, ‘Colour’ or ‘Sharpness’.Press the b button. Press the B or b button to adjust the setting. Pressthe OK button to store.

6. Press the MENU button to exit the TV menu system and return to normalTV operation.

1. Press the MENU button on the remote control to display the TV menusystem on the TV screen.

2. Press the v button to select the ‘Sound Adjustment’ menu.

3. Press the b button to enter the ‘Sound Adjustment’ menu.

4. The ‘Sound Effect’ option is highlighted. Press the b button.

5. Press the V or v button to highlight ‘Personal’, ‘Dolby V’, ‘Dynamic’ and‘Natural’ Press the OK button to confirm.

6. a) If you have selected ‘Dolby V’, ‘Natural’ or ‘Dynamic’:Go to step 7.

b) If you have selected ‘Personal’:You can now adjust the sound using the ‘Equaliser Adjustment’ option.

With the ‘Equaliser Adjustment’ option highlighted, press b to adjust.Press B or b to select the required frequency band. Press V or v to adjustthe frequency level. Press OK to confirm.

7. Press the MENU button to exit the TV menu system and return to normalTV operation.

Adjusting the Brightness, Colour and Sharpness settings7

Adjusting the sound settings8

The ‘Picture Adjustment’ menu.

The ‘Sound Adjustment’ menu.

z *When ‘Dolby V’ is selected, the TVsimulates the full effects of Dolby ProLogic Surround sound without the needfor additional speakers. Manufacturedunder licence from Dolby Laboratories.‘Dolby’, ‘Pro Logic’ and the ; symbolare trademarks of Dolby Laboratories.

**’Dynamic’ and ‘Natural’ are functionsof the ‘BBE High Definition SoundSystem’. This system enhances clarity,detail, presence of sound and increasedmusical realism.

Sound Adjustment

Sound Effect

EqualiserAdjustment

Virtual EffectBalanceAuto Vol. ControlDual Sound

Select: Enter:

/Audio-out Vol.iDual Soundi

StereoOff

Stereo

Dolby V

Picture Adjustment

PersonalPicture ModeContrastBrightnessColourSharpness

ResetAINoise ReductionDRC-MFColour Tone

OnAuto

DRC1250Cool

Select: Enter:

Basic Operation

Basic Operation 7

Overview of the remote control1 % - Mute button

Press to mute the TV sound. Press again to restore.

2 VIDEO I/1 - VCR/DVD Standby buttonPress to switch off your VCR/DVD player temporarily. Press again to return tonormal operation.

3 TV I/1 - TV Standby buttonPress to switch off the TV temporarily. The red standby indicator on the front of theTV is lit. Press again to return to normal operation.

4 - Screen Mode buttonPress to change the screen mode. Refer to page 10.

5 DIGITAL/a - Digital/Analogue mode, TV buttonIn TV mode: Press to switch between digital and analogue mode.In analogue text, video input mode, TV menu system, INFO menu, EPG andChannel Index menu: Press to return to normal TV operation.

6 / - Input Select/Text Hold buttonIn TV mode: Press to view signals from equipment connected to the TV sockets.Refer to page 27 .In analogue text mode: Press to hold the current page. Refer to page 13.

7 Numbered buttonsIn TV mode: Press to select the required channel number. For channel numbers 10and above, enter the second digit within two seconds.In analogue text mode: Press to enter the three digital page number. Refer to page 13.

8 GUIDE - Guide buttonIn digital TV mode: Press to access digital text and interactive services (dependingon availability).

9 - Previous channel buttonIn analogue TV mode: Press to return to the previous channel watched (providedthat the channel was watched for more than five seconds).In digital TV mode: Press to remove any interactive prompts from the TV screen.In digital text mode: Press to cancel a selection/go back a step. Refer to page 12

q; MODE - Remote control mode selectorThis remote control can be programmed to operate the basic functions of most DVDplayers and VCRs. Once programmed, press this button repeatedly to select TV,VCR or DVD mode. Refer to page 28.

qa •REC - VCR RECORD buttonWith the remote control in VCR mode: Press to start your VCR’s RECORD function

qs / - Text buttonIn digital TV mode: Press to access digital text. Refer to page 12.In analogue TV mode: Press to access analogue text. Refer to page 13.

qd INDEX - Channel Index buttonIn digital TV mode: Press to access the Channel Index menu. Refer to page 14.

qf - EPG button (Electronic Programme Guide)In digital TV mode: Press to access the Digital EPG. Refer to page 15.

qg - INFO buttonIn digital TV mode: Press to access the Info menu. Refer to page 17.In analogue TV mode: Press to display information such as current channel numberand screen mode. Press again to cancel.

qh OK buttonIn TV menu system: Press to confirm a selection. Refer to page 20.In digital TV mode: Press to access the Channel Index menu. Refer to page 14.In analogue TV mode: Press to access the Programme Index table. Press the V or v buttonto highlight an analogue channel. Press the b button to display the chosen channel.

qj V, v, B and b buttonsIn TV menu system: Press to move through the options. Refer to page 20.

qk Coloured buttonsIn digital menu systems: Press to select the options at the bottom of the screen inthe Info, Main, Channel Index and EPG digital menus.In analogue text mode: Press to use Fastext. Refer to page 13.

ql 2 +/- Volume buttonsPress to increase (+) or decrease (-) the TV volume.

w; PROG +/- buttonsIn TV mode: Press to view the next (+) or previous (-) channel.In analogue text mode: Press to view the next (+) or previous (-) page. Refer to page 13.

wa MENU buttonPress to access the TV menu system. Refer to page 20.

DIGITAL/a

GUIDE

MODE

INDEX

5

1

64

7

2

8 9

wa

3

q; qa

qs qd

qj

qhqf qg

ql w;

qk

Basic Operation

8 Basic Operation

1 0 - Reset buttonPress to return picture and sound levels to the factory settings.

2 t - Video Input buttonPress to view pictures from equipment connected to the TV sockets.

3 2 +/- buttonsPress to increase (+) or decrease (-) the TV volume.

4 PROG +/- buttonsIn TV mode: Press to view the next (+) or previous (-) channel.

5 ! - On/Off buttonPress to switch the TV on or off.

Overview of the TV buttons

100HzDigtial Plus

100HzDigital Plus

Press gently on the symbol to open the door.

4 4 o4

51 2 3 4

4 4 o4

Basic Operation

Basic Operation 9

Everyday useThis section explains the various functions and operations used during everydayviewing. Most operations can be done using the remote control.

1. Press the On/Off button (labelled !) on the front of the TV to switchon the TV.When the TV is in standby mode (the 1 indicator on the TV is lit red),press the TV I/1 button on the remote control to switch on the TV.

2. Press the PROG+/- buttons on the TV or press the PROG+/- orNumbered buttons on the remote control to select a TV channel.When selecting double digit numbers using the Numbered buttons, enterthe second digit within two seconds.

3. Press the 2 +/- buttons on the TV or on the remote control to adjust thevolume.

Additional operations

To Press

Turn off the TV temporarily (standby)...

TV I/1 on the remote control. When the TV is in standby mode the 1 indicator on the TV is lit red. Press again to return to normal TV operation.

Mute the sound... % button on the remote control. Press again to cancel.

Switch between analogue and digital mode...

DIGITAL/a button.If the TV is in digital mode an information banner appears briefly on screen when you change channels.If the TV is in analogue mode the channel number appears in green lettering when you change channels.

Change the Screen Mode... button. Refer to page 10.

Watch pictures from equipment connected to the TV’s front and rear sockets (video input mode)...

t button on the TV or t/ button on the remote control repeatedly until the picture appears. Refer to page 27.

z For example, if you wish to view pictures from a DVD player connected to the 2socket on the rear of the TV, press the t/ button repeatedly until the 2symbol appears on the TV screen together with the DVD picture.Please note, most equipment connected to the rear sockets, when activated, willsend a signal to the TV. The TV will automatically display the picture for you.

Access text services (depending on availability of service)...

/ button on the remote control.Refer to pages 12 and 13.

Access the Digital Electronic Programme Guide (EPG)...

button on the remote control.Refer to page 15.

Return to normal TV operation (from text, video input mode, TV menu system, INFO menu, EPG and Channel Index menu)...

DIGITAL/a button.

4 4 o4

On/Offbutton

t button

PROG +/-buttons

2 +/-buttons

DIGITAL/a

GUIDE

MODE

INDEX

DIGITAL/a button

t/button

Numberedbutton

button

/button

PROG +/-buttons

2 +/- buttons

% button TV I/1 button

button

Basic Operation

10 Basic Operation

Screen ModeThe picture that the TV receives may be in one of several formats (e.g. conventional4:3 format, 16:9 widescreen format etc.). You can alter the TV screen modemanually to suit the broadcast you are watching*. (Alternatively, set the ‘AutoFormat’ menu option to ‘On’. The TV will automatically select the best mode to suitthe broadcast. Refer to page 22 for details.)

1. Press to display the ‘Screen Mode’ menu on the TV screen.

2. Press repeatedly (or use V or v) to select one of the following modes.

3. Press OK to confirm.

WideUse this mode for watching widescreen broadcasts (e.g. Digital / Satellite TV,DVD).

ZoomUse this mode for watching cinemascopic (letter box format) broadcasts (e.g.movies in letter box format). Due to the range of cinemascopic formats available,black areas may be visible on the TV screen. In ‘Zoom’ mode, parts of the topand bottom of the picture may be cut off. Press the V or v button to adjust theposition of the picture on the TV screen (e.g. to read subtitles).

14:9Use this mode for watching 14:9 broadcasts with the picture displayed in thecorrect proportions. As a result, black areas are visible on the TV screen. In‘14:9’ mode, parts of the top and bottom of the picture may be cut off. Press theV or v button to adjust the position of the picture on the TV screen (e.g. to readsubtitles).

Cinamascopic (letter box) broadcast viewed in ‘Zoom’ mode.

14:9 broadcast viewed in ‘14:9’ mode.

Widescreen (16:9) broadcast viewed in ‘Wide’ mode.

100HzDigtial Plus

100HzDigtial Plus

100HzDigtial Plus

z *When viewing a HD signal fromexternal equipment, only ‘Wide’ and ‘4:3’modes are available.

Basic Operation

Basic Operation 11

4:3Use this mode for watching conventional 4:3 broadcasts (e.g. non widescreenTV) with the picture displayed in the correct proportions. As a result, black areasare visible on the TV screen.

SmartThis mode creates an imitation widescreen effect for conventional 4:3broadcasts. The 4:3 picture is stretched to fill the TV screen, eliminating anyblack areas. In ‘Smart’ mode, parts of the top and bottom of the picture may becut off. Press the V or v button to adjust the position of the picture on the TVscreen (e.g. to read subtitles).

4:3 broadcast viewed in ‘4:3’ mode.

4:3 broadcast viewed in ‘Smart’ mode

100HzDigtial Plus

100HzDigtial Plus

Basic Operation

12 Basic Operation

Digital textSome broadcasters now provide a digital text service. Digital text services offer allthe familiar information that analogue (conventional) text services provide but withthe look and feel of a graphically rich website.

The appearance, content and navigation methods of all digital text services aredecided by the broadcaster. Most of the digital text services currently available usesimple navigation methods based on the following buttons:

Viewing digital textThere are two ways to view digital text, either while watching a digital channel or byaccessing a dedicated digital text channel.

a) Digital text from digital channels(depending on availability of service)

This form of digital text is accessed the same way as analogue text.

b) Digital text from a dedicated digital text channel(depending on availability of service)

Some broadcasters provide a separate channel for accessing their digital textservice.

To Press

Load or exit digital text... / button.

Move around the screen... V, v, B or b buttons.

Select items on screen... OK and Numbered buttons.

Cancel a selection/go back a step... button.

Access shortcuts... Coloured buttons.

1. Select a digital channel which provides a text service.

2. Press / to access the digital text service.

3. Follow the on screen instructions.

1. Select a dedicated digital text channel.

2. Follow the on screen instructions.

An example of digital text.

Basic Operation

Basic Operation 13

Analogue textMost analogue TV channels broadcast a text service. The index page (usually page100) provides information on how to use the service. Please ensure that you arereceiving a good signal, or some text errors may occur.

FastextFastext allows you to access pages quickly and easily. When Fastext is available,four coloured items appear at the bottom of the text page. Press the correspondingColoured button on the remote control to access the page.

Page CatchingThis feature allows you to jump quickly from one page to another. When viewing apage that contains several page numbers (e.g. an index page), press OK. Press Vor v to highlight the required page number. Press OK to select. Your chosen pageappears on the TV screen.

1. Select an analogue channel that provides a text service.

2. Press the / button to access the text service.

3. To Press

Select a page... Numbered buttons.

Select a sub-page... B or b buttons.

Select full screen text mode /Superimpose the text over the TV picture (mix mode)...

/ button repeatedly.

Hold a page... / button. Press again to cancel.

Reveal hidden information... / button.

4. Press the DIGITAL/a button to return to normal TV operation.

An example of analogue text.

Advanced Operation

14 Advanced Operation

The Channel Index menu The Channel Index menu provides a list of all the available digital channels, along

with information about the programmes currently being broadcast*. The currentchannel is previewed in the top right corner of the screen with it’s channel name andnumber displayed below it.

The Channel Index menu is only available in digital mode.

The Category pop-up listThe Category pop-up list allows you to display channels in the Channel Index menuby category.

The categories available include:

Favourite channelsThis feature allows you to create a list of your favourite channels. This list isdisplayed when the ‘Favourite’ category is selected in the Channel Index menu (seeabove).

To add a channel to the Favourite categoryWith the required channel highlighted in the Channel Index menu, press the BLUEbutton to add the channel to the Favourite list.

To remove a channel from the Favourite categoryAccess the Category pop-up list (see above). Use the V or v button to highlight the‘Favourite’ category. Press the OK button to display the ‘Favourite’ category. Usethe V or v button to highlight the channel you wish to remove from the Favourite list.Press the BLUE button to remove the channel.

1. With the TV in digital mode, press the OK button to display the ChannelIndex menu.

2. To Press

Move around the menu... V and v buttons.

Display the previous/next six channels in the list...

RED button (previous), GREEN button (next).

Preview a programme... OK button while highlighting a programme**.


Favourite Contains all the channels you have stored as a favourite (seebelow).

Choice The TV will create this list based on the type of channels youwatch the most.

Recent Prog. Contains the last five channels watched.

All Categories Contains all available channels.

News Contains all news channels.

1. Press the YELLOW button whilst accessing the Channel Index menu.

2. Press the V or v button to highlight the required category.

3. Press the OK button. The Channel Index menu now only shows channelsfrom the category selected. The category name is displayed at the top ofthe channel list.

The ‘Channel Index’ menu.All Categories

Thu 3 Jul13:07

01 BBC ONEBBC News

02 BBC 2Wimbledon 2003

03 ITV 1Everything Must Go

04 CHANNEL 4This Happy Breed

05 fiveFamily Affairs

06 ITV 2Emmerdale

01 BBC ONE

Press OK key to exit Index.

Previous Next Category Add

13:00-13:30

12:00-14:30

13:00-13:30

12:45-14:45

13:00-13:30

13:00-13:30

z *Depending on availability of service.Information will only be displayed if theTV station is transmitting it.

**If you have set a Parental Control agelimit in the Main Menu, and theprogramme exceeds that limit, you willbe asked to enter your PIN before thepreview is allowed. Programmes thatexceed the age limit are identified by a symbol.

Initially the PIN code is preset to 1234.Refer to ‘PIN Code’ on page 19 for moreinformation.

Advanced Operation

Advanced Operation 15

The Digital Electronic Programme Guide (EPG)

The Digital Electronic Programme Guide allows you to:

a) view programme information for all digital channels*,b) sort programme information by category,c) set reminders to have the TV automatically switch to a programme when it starts,d) record programmes

The Digital Electronic Programme Guide is only available in digital mode.

The Category pop-up listThe Category pop-up list allows you to display channels in the Digital ElectronicProgramme Guide by category.

The categories available include:

To add/remove a channel to/from the Favourite listRefer to ‘To add a channel to the Favourite category’ and ‘To remove a channelfrom the Favourite category’ on the previous page.

Recording

1. With the TV in digital mode, press the button to display the DigitalElectronic Programme Guide.

2. To Press

Move around the menu... V, v, B and b buttons.

Display the previous/next five channels in the list...

RED button (previous), GREEN button (next).

Preview a programme... OK button while highlighting a programme**.


Favourite Contains all the channels you have stored as a favourite(see below).

Choice The TV will create this list based on the type of channelsyou watch the most.

Recent Prog. Contains the last five channels watched.

All Categories Contains all available channels.

News Contains all news channels.

1. Press the YELLOW button whilst accessing the Digital ElectronicProgramme Guide.

2. Press the V or v button to highlight the required category.

3. Press the OK button. The Digital Electronic Programme Guide now onlyshows channels from the category selected. The category name isdisplayed at the top of the channel list.

1. With the Digital Electronic Programme Guide on screen, press the V, v,B and b button to highlight the programme you wish to record.

2. Press the OK button to display the ‘Timers’ menu.

3. Press the RED button to set the TV timer***.

The ‘Digital EPG’.All Categories

Thu 3 Jul13:07

01 BBC ONEBBC News

01 BBC ONE

Previous Next Category

All the latest news and sport.

Timer List

Press OK key to exit

13:00 13:30 14:00 14:30

02 BBC 2

03 ITV 1

04 CHANNEL 4

05 five

BBC News Reg... Wimbledon 2003

Wimbledon 2003 The Bride Walks Out

Everything... Quincy, ME Shortland...

This Happy Breed

Family Aff... Brain Teaser Charlie's..

z *Depending on availability of service.EPG data will only be displayed if the TVstation is transmitting it.

**If you have set a Parental Control agelimit in the Main Menu, and theprogramme exceeds that limit, you willbe asked to enter your PIN before thepreview is allowed. Programmes thatexceed the age limit are identified by a symbol.

Initially the PIN code is preset to 1234.Refer to ‘PIN Code’ on page 19 for moreinformation.

z ***You will now have to manually set yourVCR timer.

When a programme has been set torecord, a solid green bar appears underthe information box in the EPG for thatprogramme.

Advanced Operation


Timed display

Manual timer

Cancelling a timed event

1. With the Digital Electronic Programme Guide on screen, press the V, v,B and b button to highlight the programme you wish to display.


3. Press the GREEN button to have the TV automatically display theselected programme when the programme starts.

1. With the Digital Electronic Programme Guide on screen, press the BLUEbutton to display the Timer List menu.

2. Press the RED button to display the ‘Manual Timer Record’ menu.

A message is displayed reminding you to set your VCR timer. Press theRED button to remove the message.

3. Press the V or v button to select the date. Press the b button.

4. Press the V or v button to select the start time. Press the b button.

5. Press the V or v button to select the stop time. Press the b button.

6. Press the V or v button to select the channel. Press the OK button tostore. The ‘Timer List’ menu is displayed.

7. Press the BLUE button to return to the EPG menu or the DIGITAL/abutton to return to normal TV operation.


2. Press the V or v button to highlight the programme/event you wish tocancel.

3. Press the YELLOW button to cancel the programme/event. Press theRED button to confirm.

Advanced Operation


Timed display

Manual timer

Cancelling a timed event

1. With the Digital Electronic Programme Guide on screen, press the V, v,B and b button to highlight the programme you wish to display.


3. Press the GREEN button to have the TV automatically display theselected programme when the programme starts.


2. Press the RED button to display the ‘Manual Timer Record’ menu.

A message is displayed reminding you to set your VCR timer. Press theRED button to remove the message.

3. Press the V or v button to select the date. Press the b button.

4. Press the V or v button to select the start time. Press the b button.

5. Press the V or v button to select the stop time. Press the b button.

6. Press the V or v button to select the channel. Press the OK button tostore. The ‘Timer List’ menu is displayed.

7. Press the BLUE button to return to the EPG menu or the DIGITAL/abutton to return to normal TV operation.


2. Press the V or v button to highlight the programme/event you wish tocancel.

3. Press the YELLOW button to cancel the programme/event. Press theRED button to confirm.

Advanced Operation


The Info menuThe Info menu provides information on the programmes currently being shown andon future programmes. It also allows you to display digital subtitles and listen to thebroadcast in a different language*.

The Info menu is only available in digital mode.

The Coloured buttons give you access to further options:

1. With the TV in digital mode, press the button to display the ‘Info menu’.

2. To Press

Display information for future programmes...

b button.

Return to information for current programmes...

B button.

Change the TV channel... Numbered buttons.


RED button: Subtitles(depending on availability)When pressed, a pop-up menu allows you to change thelanguages for the subtitles. Press the V or v button toselect the language required, then press the OK button toconfirm.

GREEN button: Audio(depending on availability)When pressed, a pop-up menu allows you to select thelanguage in which you wish to hear the broadcast. Pressthe V or v button to select the language required, thenpress the OK button to confirm.

YELLOW button: REC/TimersAllows you to record a programme from the Info display, orset a programme to automatically appear on screen whenit starts. Press the B or b button to select futureprogrammes from the Info display, then press theYELLOW button to display the ‘Timers’ pop-up menu. Youcan now choose from a)Record b)Wakeup or c)Manual

a) Record Highlight ‘Record’ and press OK toautomatically set your VCR to record theselected programme.

b) Wakeup** Highlight ‘Wakeup’ and press OK if youwish the future programme you selectedto appear on screen when transmissionbegins.

c) Manual** Highlight ‘Manual’ and press OK if youwish the TV to output a channel to yourVCR for recording. Press the V or v

button to set the day of recording, thenpress the b button to move to the starttime. Repeat this procedure to set thestart and stop times and the channelnumber, then press the OK button tostore and return to the Info menu. Pressthe button to remove the Info menufrom the screen. You must now set thetimer recording function of your VCR toswitch on and off to correspond with theprogramme you have stored forrecording.

BLUE button: Press to display the Main Menu (see next page).

The ‘Info’ menu.All Categories

Thu 3 Jul13:07

Subtitles

01

Set-upAudio

BBC News; Weather

All the latest news and sport.

Regional News; Weather13:30-13:45

z **After you have programmed a‘Wakeup’ or ‘Manual’ recording you canput the TV into it’s standby mode, but donot switch off completely or therecording will be cancelled. If you put theTV into standby mode, the standbyindicator on the front of the TV flashesgreen periodically to remind you arecording has been programmed. Oncea programme has started recording, donot change channels or switch toanalogue mode or the recording will becancelled.

z *Depending on availability of service.Information, subtitles and differentlanguages are only available if the TVstation is transmitting the necessaryinformation.

Advanced Operation


The Main MenuThis menu contains features that allow you to customise the digital side of your TV.The ‘Main Menu’ is only available in digital mode.

1. With the TV in digital mode, press the button to display the ‘Info menu’.

2. Press the BLUE button to access the ‘Main Menu’.

3. To Press

Highlight an option... V and v buttons.

Select a highlighted option... OK button.

Alter the settings of a selected option...

V, v, B or b buttons.

Store settings/changes... OK button.


Favourite ProgrammeThis option allows you to store your favourite channels in a list for quick access.

To add a channel to the Favourite Programme listWith the ‘Favourite Programmes’ option highlighted, press the OK button todisplay the ‘Favourite Programmes’ menu. Press the V or v button to scrollthrough the list until the channel you wish to store as a favourite is highlighted.Press the OK button to confirm. A tick appears alongside the channel to indicatethat it is now stored as a favourite. Repeat this procedure to store other favouritechannels.

To remove a channel from the Favourite Programme listHighlight the channel and press the OK button. The tick disappears.

To remove all channels from the Favourite Programme listPress the YELLOW button.

WallpaperThis option allows you to customise the background pattern for all digital menus.

With the ‘Wallpaper’ option highlighted, press the OK button to display the‘Wallpaper’ menu. Press the V or v button to highlight the required wallpaper.Press the OK button to confirm.

Parental ControlThis option allows you to set an age limit above which a PIN code is requiredbefore viewing is allowed.

With the ‘Parental Control’ option highlighted, press the OK button to display the‘Parental Control’ menu. Enter your existing PIN code using the Numberedbuttons*. Press the OK button to confirm. The age box now becomes active.Press the V or v button to highlight the required age limit. Press the OK buttonto confirm.

Auto TuningAll the available digital channels were tuned in when the TV was first installed.This option allows you to repeat that process (e.g. to search for new channelsthat have been launched by broadcasters).

With the ‘Auto Tuning’ option highlighted, press the OK button to display the‘Auto Tuning’ menu. Press the RED button to start the auto tuning process.

Detail Set-upThe ‘Detail Set-up' menu is explained on page 20.

CA Set-upThe ‘CA Set-up' option is for future use only.

The ‘Main’ menu.Digital Set-up

Exit

Main Menu

Press OK key to enter

Favourite ProgrammesWallpaperParental ControlAuto TuningDetail Set-upCAM Set-up

z *Initially the PIN code is preset to 1234.Refer to ‘PIN Code’ on page 20 fordetails on how to change this.

Advanced Operation


Detail Set-up menuThis menu allows you to configure the digital side of your TV.

1. With the TV in digital mode, press the OK button to display the ChannelIndex menu.

2. To Press

Highlight an option... V and v buttons.

Select a highlighted option... OK button.





Manual TuningThis option allows you to tune digital channels one by one.

With the ‘Manual Tuning’ option highlighted, press the OK button to display the‘Manual Tuning’ menu. Press the V or v button to highlight the channel numberfor your new channel. (Alternatively, press the RED or GREEN button to displaythe previous or next five channels in the list.) Press the OK button to display the‘Manual Programme Search’ menu. Press the b button to highlight ‘SelectSearch’. Press the V or v button to start searching. All the available channelsare displayed on the right side of the menu. Press the V or v button to highlightthe required channel. Press the OK button to store.

Clearing a channelWith the ‘Manual Tuning’ option highlighted, press the OK button to display the‘Manual Tuning’ menu. Press the V or v button to highlight the channel numberyou wish to clear. Press the YELLOW button. A message is displayed askingyou to confirm. Press the RED button to clear the channel or press the BLUEbutton to cancel.

PIN CodeThis option allows you to change your PIN code.

With the ‘PIN Code’ option highlighted, press the OK button to display the ‘PINCode’ menu. Use the Numbered buttons to enter your existing PIN code. Initiallythe PIN code is preset to 1234. If you enter a wrong number, press the REDbutton to clear and start again. If you have forgotten your PIN code, please use9999. This Pin Code will always be accepted. Press the OK button to confirm.Use the Numbered buttons to enter your new PIN code. Press the OK button toconfirm. Enter your new PIN again to confirm. Press the OK button to changethe PIN.

System InformationThis is an information screen only and displays the current software versionsand the signal strength.

With the ‘System Information’ option highlighted, press the OK button to displaythe ‘System Information’ screen.

The ‘Detail Set-up’ menu.Digital Set-up

Detail Set-up

Press OK key to enter

Manual TuningPIN CodeSoftware DownloadSystem Information

Back

Advanced Operation


Using the TV menu system Use the following buttons to operate the TV menu system.

The individual menus are explained on the following pages.

Picture Adjustment menu

1. To Press

Access the TV menu system... MENU button.

Highlight an option... V or v buttons.

Enter the highlighted menu or option...

b button.

Return to the last menu or option... B button.




2. Press the MENU button to return to normal TV operation.

Picture ModeThis option allows you to choose between four picture mode settings, ‘Live’,‘Personal’, ‘Movie’ and ‘Game’. ‘Live’, ‘Movie’ and ‘Game’ are preset modes andonly the ‘Contrast’ setting can be adjusted. ‘Personal’ mode however, alsoallows you to adjust the ‘Brightness’, ‘Colour’ and ‘Sharpness’ settings.

With the ‘Picture Mode’ option highlighted, press b to adjust. Press V or v toselect the required mode. Press the OK button to confirm.

Contrast, Brightness*, Colour*, Sharpness*, Hue**These options allow you to adjust the contrast, brightness, contrast, sharpnessand hue.

‘Brightness’, ‘Colour’ and ‘Sharpness’ can only be adjusted when the picture‘Mode’ is set to ‘Personal’. ‘Sharpness’ is not adjustable in digital mode. ‘Hue’ isonly available when viewing an NTSC colour signal, e.g. USA video tapes.

With the required option highlighted, press b to adjust. Press B or b to set thelevel. Press OK to confirm.

ResetThis option resets all picture settings to the factory preset levels.

With the ‘Reset’ option highlighted, press OK to restore default picture settings.

AI (Artificial Intelligence)This option monitors the picture and limits any sudden increases in brightnessand contrast.

With the ‘AI’ option highlighted, press b to adjust. Press V or v to select ‘On’ or‘Off’. Press OK to confirm.

Noise Reduction***Sometimes a weak signal can result in a ‘snowy’ picture (called Picture Noise).This option can help to reduce this effect.

With the ‘Noise Reduction’ option highlighted, press b to adjust. Press V or v toselect ‘High’, ‘Mid’, ‘Low’, ‘Auto’**** or ‘Off’. Press OK to confirm.

DRC-MF***** (Digital Reality Creation - Multi Function)This option allows you to enjoy higher quality pictures on your TV.

With the ‘DRC-MF’ option highlighted, press b to adjust. Press V or v to select‘Progres.’, ‘DRC1250’ or ‘DRC 100’. Press OK to confirm.

Colour ToneThis option allows you to alter the tint of the picture.

With the ‘Colour Tone’ option highlighted, press b to adjust. Press V or v toselect ‘Warm’, ‘Standard’ or ‘Cool’. Press OK to confirm.

The ‘Picture Adjustment’ menu.

z *Only adjustable when ‘Picture Mode’ isset to ‘Personal’.

**Only available when viewing an NTSCcolour signal (e.g. US video tape).

***Not available in Digital mode or whenviewing a YUV signal (HD orprogressive) from external equipment.

****Not available when viewing any SDsignal from external equipment.

*****When viewing a HD YUV signalfrom external equipment, the ‘DRC-MF’option is replaced by ‘Input Signal’. Thisoption is not selectable and is forinformation only, displaying the linescanning rate and frequency of theconnected HD YUV equipment.

Picture Adjustment

PersonalPicture ModeContrastBrightnessColourSharpness

ResetAINoise ReductionDRC-MFColour Tone

OnAuto

DRC1250Cool

Select: Enter:

G

MODE

INDEX

OK button

MENUbutton

V, v, B, and bbuttons

Advanced Operation


Sound Adjustment menuSound EffectThis option allows you to choose between four sound settings, ‘Personal’, ‘DolbyV*’, ‘Dynamic**’ and ‘Natural**’. ‘Dolby V’, ‘Dynamic’ and ‘Natural’ are preset andonly the ‘Balance’ setting can be adjusted. ‘Personal’ mode however, also allowsyou to adjust the ‘Equaliser Adjustment’ option.

With the ‘Sound Effect’ option highlighted, press b to adjust. Press V or v toselect ‘Personal’, ‘Dolby V’, ‘Dynamic’ or ‘Natural’. Press OK to confirm.

Equaliser Adjustment (Only available when ‘Sound Effect’ is set to ‘Personal’)This option allows you to customise the sound by adjusting five frequencybands.

With the ‘Equaliser Adjustment’ option highlighted, press b to adjust. Press B orb to select the required frequency band. Press V or v to adjust the frequencylevel. Press OK to confirm.

Virtual Effect (Only available when ‘Sound Effect’ is set to ‘Dolby V’)This option allows you to adjust the level of the surround sound effect whenlistening to a Dolby Surround Sound broadcast,

With the ‘Virtual Effect’ option highlighted, press b to adjust. Press B or b toadjust the level of effect. Press OK to confirm.

BalanceThis option allows you to set the balance of sound between the left and rightspeakers.

With the ‘Balance’ option highlighted, press b to adjust. Press B or b to set thebalance. Press OK to confirm.

Auto Vol. ControlSometimes the broadcast volume level changes (e.g. adverts tend to be louderthan programmes). This option allows you to cancel out this effect, giving aconstant volume level.

With the ‘Auto Vol. Control’ option highlighted, press b to adjust. Press V or v toselect ‘Off’ or ‘On’. Press OK to confirm.

Dual SoundWhen receiving a bilingual broadcast, this option allows you to choosewhich language to listen to:

With the ‘Dual Sound’ option highlighted, press b to adjust. Press V or vto select ‘Stereo’ to listen to the sound in stereo, ‘A’ to listen to the firstlanguage or ‘B’ to listen to the second language. Press OK to confirm.

When receiving a stereo broadcast, this option allows you to choosebetween mono and stereo sound:

With the ‘Dual Sound’ option highlighted, press b to adjust. Press V or vto select ‘Mono’ or ‘Stereo’. Press OK to confirm.

i/Audio-out Vol.This option allows you to simultaneously set the volume level for the headphonesocket and the volume level of the Audio output sockets on the rear of the TV.

With the ‘i/Audio-out Vol.’ option highlighted, press the b button to adjust. PressB or b to set the volume level. Press OK to confirm.

iDual SoundWhen receiving a bilingual broadcast, this option allows you to choosewhich language to listen to:

With the ‘iDual Sound’ option highlighted, press b to adjust. Press V orv to select ‘A’ to listen to the first language or ‘B’ to listen to the secondlanguage. Press OK to confirm.

When receiving a stereo broadcast, this option allows you to choosebetween mono and stereo sound:

With the ‘iDual Sound’ option highlighted, press b to adjust. Press V orv to select ‘Mono’ or ‘Stereo’. Press OK to confirm.

z *When ‘Dolby V’ is selected, the TVsimulates the full effects of Dolby ProLogic Surround sound without the needfor additional speakers. Manufacturedunder licence from Dolby Laboratories.‘Dolby’, ‘Pro Logic’ and the ; symbolare trademarks of Dolby Laboratories.

**’Dynamic’ and ‘Natural’ are functionsof the ‘BBE High Definition SoundSystem’. This system enhances clarity,detail, presence of sound and increasedmusical realism.

The ‘Sound Adjustment’ menu.Sound Adjustment

Sound Effect

EqualiserAdjustment

Virtual EffectBalanceAuto Vol. ControlDual Sound

Select: Enter:

/Audio-out Vol.iDual Soundi

StereoOff

Stereo

Dolby V

Advanced Operation


Features menuAuto FormatThis option can automatically detect the type of screen format being received.

With the ‘Auto Format’ option highlighted, press the b button to adjust. Press Vor v to select ‘Of’ or ‘On’. Press OK to confirm.Format Correction (Only available when ‘Auto Format’ is set to ‘On’)This option allows you to have the TV automatically switch to ‘Smart’ mode whenreceiving a 4:3 broadcast, so that the picture fills the TV screen.

With the ‘Format Correction’ option highlighted, press b to adjust. Press V or vto select ‘Off’ or ‘On’. Press OK to confirm.Sleep TimerThis option allows you to set a period of time after which the TV switches itselfinto standby mode. This can be in 10 minute intervals up to a maximum of 90minutes.

With the ‘Sleep Timer’ option highlighted, press b to adjust. Press V or v toselect the period of time required. Press OK to confirm.

AV3 OutputThis option allows you to set a signal to be output through the socket labelledi3/r3 on the rear of the TV*. If you connect a VCR to the i3/r3 socket,you can then record from equipment connected to other sockets of the TV.Please note, the TV outputs an audio/video signal for all types of input signal.

For example, to record from a camcorder to a video tape:Connect your camcorder to the 4 sockets (audio) and either the t4 or r4socket (video or S-Video) on the front of the TV. Connect a VCR to the i3/r3socket on the rear of the TV. Set the ‘AV3 Output’ option to ‘AV4’ (front sockets).Press ‘PLAY’ on the camcorder. The picture is sent through the i3/r3 socketto the VCR. Change the channel on your VCR until the picture from thecamcorder appears. Press ‘RECORD’ on the VCR.

With the ‘AV3 Output’ option highlighted, press b to adjust. Press V or v to select‘TV’, ‘AV1’, ‘AV2’ or ‘AV4’. Press OK to confirm.

Setting FunctionTV The currently selected channel is sent out the i3/r3 socket.

AV1 The signal from equipment connected to the 1 socket is sentthrough the TV and out the i3/r3 socket*.

AV2 The signal from equipment connected to the 2 socket is sentthrough the TV and out the i3/r3 socket*.

AV4 The signal from equipment connected to the front socket is sentthrough the TV and out the i3/r3 socket.

The ‘Features’ menu.

z *It is not possible to output a YUV signal.

If a YUV signal is being received throughAV1 or AV2 and the ‘AV3 Output’ optionis set to ‘AV1’ or ‘AV2’, ‘TV’ isautomatically selected.

Features

OnAuto FormatFormat Correction

Sleep TimerAV3 Output

Select: Enter:

On

OffTV

Advanced Operation


Set Up menu

Manual Set Up menu

Auto Tuning*All the available channels were tuned in when the TV was first installed. Thisoption allows you to repeat that process (e.g. to re-install the TV at an alternativelocation or to search for newly launched channels).

With the ‘Auto Tuning’ option highlighted, press b to select. The autotune promptappears on screen. Press OK to start the auto tuning process. When allavailable channels have been tuned the TV returns to normal operation.Programme Sorting*This option allows you to change the order in which the analogue channels arestored on the TV.

With the ‘Programme Sorting’ option highlighted, press b to display the‘Programme Sorting’ menu. Press V or v to highlight the channel you wish tomove to a new position, the press b to select. Press V or v to highlight the newposition, then press OK. The chosen channel has now moved to the newposition. Repeat to move other channels, if required.AV PresetThis option allows you to assign a name to any equipment connected to the TVsockets. The name is displayed briefly on screen when the equipment isselected.

With the ‘AV Preset’ option highlighted, press b to display the ‘AV Preset’ menu.Press V or v to highlight the socket you wish to name. Press b to select theAUTO FORMAT column. Press V or v to select ‘On’ or ‘Off’ (for more details on‘Auto Format’, refer to page 22). Press b to select the LABEL column. Press Vor v to select the first character. Press b to confirm and highlight the nextcharacter. Select the other characters in the same way, up to a maximum of fivecharacters). After selecting all required characters, press OK to store.Manual Set UpWith the ‘Manual Set Up’ option highlighted, press b to display the ‘Manual SetUp’ menu. The ‘Manual Set Up’ menu is explained below.

Manual Programme Preset*With the ‘Manual Programme Preset’ option highlighted, press b to display the‘Manual Programme Preset’ menu. The ‘Manual Programme Preset’ menu isexplained on the following page.Further Programme Preset*With the ‘Further Programme Preset’ option highlighted, press b to display the‘Further Programme Preset’ menu. The ‘Further Programme Preset’ menu isexplained on the following page.

Picture RotationDue to the Earth’s natural magnetism, the picture might slant slightly. This optionallows you to correct any such effect.

With the ‘Picture Rotation’ option highlighted, press b to adjust. Press V or v torotate the picture over a range of -5 to +5. Press OK to store.

Personal IDThis option allows you to enter a code which could help to trace you should theTV be stolen and later recovered. This code can only be entered once - pleasemake a note of it and keep it safe.

With the ‘Personal ID’ option highlighted, press b to adjust. Press V or v to selectthe first character of the code you wish to use. Press b to confirm and highlightthe next character. Repeat until all characters have been entered. Press OK tostore. A confirmation screen is displayed. Press OK to confirm.

The ‘Set Up’ menu.

The ‘Manual Set Up’ menu.

Set Up

StartAuto TuningProgramme SortingAV PresetManual Set Up

Select: Start Auto Tuning:

z *Not available in Digital or AV modes.

Set Up

Manual Set Up

Select: Enter:

Manual Programme PresetFurther Programme Preset

0-----------Personal ID

Picture Rotation

Advanced Operation


Manual Programme Preset menu*

This menu allows you to tune in analogue channels, one by one.

Further Programme Preset menu*

This menu allows you to fine tune and set the volume level of an individual analoguechannel.

1. With the ‘Manual Programme Preset’ option highlighted, press b todisplay the ‘Manual Programme Preset’ menu.

2. Press V or v to select the channel number you wish to manually tune.Press b twice to select the ‘SYS’ column. Press V or v to select ‘AUS’ forTV broadcasts or ‘EXT’ for connected equipment. Press b to confirm andselect the ‘CH’ column.

3. Press V or v to select the required channel tuning (C for terrestrialchannels, S for cable channels or F for direct frequency input). Press bto confirm

4. You now need to tune the channel using one of the following methods:

a) If you do not know the channel number (frequency):Press v to select ‘SEARCH’. The TV automatically searches for thenext available TV broadcast channel or the VCR test signal. When achannel has been found, press OK to store or v to continuesearching.

b) If you know the channel number (frequency):Use the Numbered buttons to enter the channel number of thebroadcast you want or your VCR channel number. Press OK toconfirm.

c) For connected equipment (EXT):Press v to select ‘AV1’, ‘AV2’, ‘AV3’ or ‘AV4’, depending on whichsocket you have connected your equipment to. Press OK to confirm.

5. Press B or b to select the ‘LABEL’ column. This option allows you toassign a name of your choice (up to five letters or number). The name isdisplayed briefly on screen when the channel is selected.

Press V or v until the letter or number you require appears in the display(select ‘-’ for a blank space). Press b to confirm. Repeat this until thename is complete. Press OK to confirm.

6. Press B or b to highlight ‘Skip’. This option allows you to skip unusedanalogue channels when selecting channels with the PROG +/- buttons.(You can still select a skipped channel using the Numbered buttons onthe remote control.)

Press b the setting. Press V or v to select ‘Yes’ or ‘No’. Press OK toconfirm.

1. With the ‘Further Programme Preset’ option highlighted, press b todisplay the ‘Further Programme Preset’ menu.

2. Press V or v to select the channel number you require. Press b

repeatedly to highlight one of the following options:

a) VOL (Automatic Volume Offset):This option allows you to set the volume level for an individualanalogue channel. Press V or v to adjust the volume level over arange of -7 to +7. Press OK to confirm.

b) AFT (Automatic Fine tune):This option allows you to fine tune an analogue channel. Press V orv to select ‘On’. Alternatively, press V or v to manually adjust thetuning frequency over a range of -15 to +15. Press OK to confirm.

The ‘Manual Programme Preset’ menu.Manual Programme Preset

Select: Enter:

PROG SKIPPROG SYS CH LABEL

910111213141516171819

OffOffOffOffOffOffOffOffOffOffOff

AUSAUSAUSAUSAUSAUSAUSAUSAUSAUSAUS

C41C62C52C66S17S32C47C44C41C37C47

ABCSEVEN

NineTen

31SBS

The ‘Further Programme Preset’ menu.Further Programme Preset

Select: Enter:

PROGPROG VOL AFT

00000000000

OnOnOnOnOnOnOnOnOnOnOn

910111213141516171819

z *For analogue channels only (notavailable in Digital or AV modes).

Connecting Other Equipment

26 Connecting Other Equipment

1 i3/r3 - AV3 Scart socket (S-Video enabled)Use to connect a VCR.

2 2 - AV2 Scart socket (YUV, HD enabled)Use to connect equipment such as DVD players, satellite/cable decoders.

3 1 - AV1 Scart socket (YUV, HD enabled)Use to connect equipment such as DVD players, satellite/cable decoders.

4 ANALOGUE - Aerial socket (Analogue)If you are connecting a VCR: Use to connect to the RF OUT* socket onyour VCR.If you are not connecting a VCR: Use the supplied RF lead to connect tothe socket labelled .

5 - Audio out socketsUse to connect audio equipment such as a Hi-Fi, Surround Sound system.

6 DIGITAL - Aerial socket (Digital)Use to connect your existing aerial.

7 - Aerial socket (RF Out)If you are connecting a VCR: Use to connect to the RF IN* socket on yourVCR.If you are not connecting a VCR: Use the supplied RF lead to connect tothe socket labelled ANALOGUE .

8 SERVICE - Service socketFor service use only.

9 MODEM - MODEM socketFor service use only.

q; OPTICAL OUTPUT - Digital Out (audio)Use to connect to an external amplifer/surround sound system.

qa - PCMCIA socketFor future use only.

z *Socket names may vary depending onmake and model of VCR. Refer to yourVCR instruction manual for details.

Please note that Smartlink is notsupported by this TV.

Overview of the rear sockets

1

2

3

4

5

76

8

9

q;

qa


Connecting Other Equipment 27

1 i - Headphone socketUse to connect headphones.

2 r4 - AV4 S-Video input*Use to connect equipment such as S-VHS camcorders.

3 t4 - AV4 Video input*Use to connect equipment such as camcorders, PlayStation 2.

4 o4 - AV4 Audio inputUse to connect equipment such as camcorders, PlayStation 2.

Overview of the front sockets

100HzDigtial Plus

100HzDigital Plus

Press gently on the symbol to open the door.

z *To avoid picture distortion, do notconnect equipment to the r4 and t4sockets at the same time.

4 4 o4

4 4 o4

1 2 3 3



Connecting other equipment to the TV A wide range of equipment can be connected to the TV through the front and rear

sockets. Most equipment can be connected to any of the TV sockets. Refer to theinstruction manual supplied with your equipment to determine the best TV socketto use. This TV supports the following inputs:

Connecting HD equipment Use the supplied Scart Adaptor to connect HD equipment to the 1 or 2

sockets on the rear of the TV.

Viewing pictures from equipment connected to the rear sockets

Viewing pictures from equipment connected to the front sockets

TV Sockets Socket type(s) Inputs supported

1 Scart YUV, HD, Audio/Video.

2 Scart YUV, HD, Audio/Video.

i3/r3 Scart S-Video, Audio/Video.

o4 and r4 Phono (x2),4 pin DIN

Audio/S-Video.(audio via o4 sockets, S-Video via r4 socket)

o4 and t4 Phono (x3) Audio/Video.(audio via o4 sockets, video via t4 socket)

1. Switch on/press ‘PLAY’ on the connected equipment. The picture (if any)from the equipment appears on the TV screen.

If the picture does not automatically appear press the / buttonrepeatedly until the picture is displayed on the TV screen.


1. Press the / button repeatedly until the t4 symbol appears on theTV screen.

2. Switch on/press ‘PLAY’ on the connected equipment. The picture (if any)from the equipment appears on the TV screen.



Connecting Other Equipment 29

Remote control of other equipment The remote control supplied with your TV automatically operates the basic

functions of Sony DVD players and most Sony VCRs. The remote control can alsooperate DVD players and VCRs made by other manufacturers, provided that it isfirst programmed to match the particular brand of your VCR or DVD player**.

Programming the remote control

1. Find the three digit code for your brand from the list below.

2. If programming the remote control to operate a DVD player:Press the MODE button repeatedly until the green DVD light illuminates.

If programming the remote control to operate a VCR:Press the MODE button repeatedly until the green VCR light illuminates.

3. With the green light illuminated, press and hold down the YELLOWbutton for approximately six seconds, until the light starts to flash.

4. Use the Numbered buttons to enter the three digit code for your brand(refer to table, below). Once a correct code has been entered, the greenVCR, TV and DVD lights illuminate together momentarily.

5. Turn on your VCR or DVD player and check that the remote controloperates the basic functions (refer to ‘Controlling a DVD player’,‘Controlling a VCR’ on the next page for details). If not, repeat steps 2-4and enter the next three digit number for your brand.

6. Press the MODE button repeatedly until the green TV light illuminates.

DVD Brand List VCR Brand List

Brand Code Brand Code

SONY 001 SONY (VHS) 301, 302,303, 308, 309

AIWA 021 SONY (BETA) 303, 307, 310

DENON 018, 027, 020, 002 SONY (DV) 304, 305, 306

GRUNDIG 009, 028, 023,024, 016, 003

AIWA 325, 331, 351

HITACHI 025, 026, 015, 004 AKAI 326, 329, 330

JVC 006, 017 DAEWOO 342, 343

KENWOOD 008 GRUNDIG 358, 355, 360361, 320, 351

LG 015, 014 HITACHI 327, 333, 334

LOEWE 009, 028, 023,024, 016, 003

JVC 314, 315, 322,344, 352, 353,354, 348, 349

MATSUI 013, 016 LG 332, 338

ONKYO 022 LOEWE 358, 355, 360361, 320, 351

PANASONIC 018, 027, 020, 002 MATSUI 356, 357

PHILIPS 009, 028, 023,024, 016, 003

ORION 328

PIONEER 004 PANASONIC 321, 323

SAMSUNG 011, 014 PHILIPS 311, 312, 313, 316,317, 318, 358, 359

SANYO 007 SAMSUNG 339, 340, 341, 345

SHARP 019, 027 SANYO 335, 336

THOMSON 012 SHARP 324

TOSHIBA 003 THOMSON 319, 350

YAMAHA 018, 027, 020, 002 TOSHIBA 337

z *The brand codes you set may be lost ifweak batteries are not replacedimmediately. Should this happen,replace the batteries and re-enter therequired codes. A small label has beenattached to the battery holder for you tomake a note of your brand codes.

DIGITAL/a

GUIDE

MODE

INDEX

MODEbutton

Numberedbutton

YELLOWbutton



Controlling a DVD player

Before attempting to control a non-Sony DVD player, ensure that the remote controlhas been programmed (refer to previous page).

Controlling a VCR

Before attempting to control a non-Sony VCR, ensure that the remote control hasbeen programmed (refer to previous page).

1. Press the MODE button repeatedly until the green DVD light illuminates.

2. Use the buttons in the table below to operate your DVD player.

3. When you have finished controlling your DVD player, press the MODEbutton repeatedly until the green TV light illuminates.

1. Press the MODE button repeatedly until the green VCR light illuminates.

2. Use the buttons in the table below to operate your VCR.

3. When you have finished controlling your VCR, press the MODE buttonrepeatedly until the green TV light illuminates.

Button Function in DVD Mode Function in VCR Mode

VIDEO I/1 Switch the DVD player on/off Switch the VCR on/off

TV I/1 Switch the TV on/off Switch the TV on/off

DIGITAL/a Return to TV mode from Video Input mode

Return to TV mode from Video Input mode

Select TV screen mode Select TV screen mode

/ Select Video Input mode Select Video Input mode

Numberedbuttons

No function Select VCR channel number

Display on screen (TV) information Display on screen (TV) information

No function Select double digit VCR channel numbers

V Pause a DVD Pause a tape

B Go to the previous chapter, track or scene

Rewind a tape

OK Play a DVD Play a tape

b Go to the next chapter, track or scene

Fast forward a tape

v Stop a DVD Stop a tape

•REC No function Start recording

2 +/- Increase (+) or decrease (-) TV volume

Increase (+) or decrease (-) TV volume

PROG +-/ No function Select next (+) or previous (-) VCR channel

% Mute the TV Mute the TV

DIGITAL/a

GUIDE

MODE

INDEX

•RECbutton

TV I/1button

VIDEO I/1button

button

button

%button

t/button

DIGITAL/abutton

Numberedbuttons

MODEbutton

2 +/-button

PROG +/-buttons

OKbutton

V, v, B andb buttons

button

Additional Information

Additional Information 31

SpecificationsTV System B/G, DVB-T

Colour System PALNTSC 3.58, 4.43 (only Video In)

Channel Coverage VHF:UHF:CATV:

0-12, 5A, 9A28-69S01-S03, S1-S41

Picture Tube FD Trinitron WIDE Approx. 82cm (32inches)

Sound Output Left/Right: 2x20W (music power), 2x10W (RMS)

Power Consumption 154W

Dimensions (w x h x d) Approx. 910 x 446 x 590 mm

Weight Approx. 67kg

Rear Terminals 1 21-pin Euro connector (CENELECstandard) including audio/videoinput, YUV input, HD input, TV audio/video output.

2 21-pin Euro connector (CENELECstandard) including audio/videoinput, YUV input, HD Input, TV audio/video output.

i3/r3 21-pin Euro connector (CENELECstandard) including audio/videoinput, S-VIDEO input, selectableaudio/video output.

DIGITAL RF In (Digital)

ANALOGUE RF In (Analogue)

RF Out

Audio output - phono jacks.

PCMCIA (for future use only).

MODEM MODEM jack (for service only).

OPTICAL OUTPUT Digital Out (Optical)

Front Terminals i Headphone jack - minijack stereo.

r4 S-Video input - 4 pin DIN.

t4 Video input - phono jack.

o4 Audio inputs - phono jack.

Supplied Accessories RM-935 remote control (1)IEC designated size AAA (R03) battery (2)RF Lead (1)Scart Adaptor (1)Scart Lead (1)

Design and specification are subject to change without notice.


32 Additional Information

Troubleshooting

Here are some simple solutions to problems which may affect the picture and sound.

Problem Cause Solution

No picture, no sound. • Power off.

• TV in standby.

• Aerial disconnected.

• Plug in the TV.

• If the 1 indicator is lit, press the TV I/1 button on the remote control.

• Press the ! button on the front of the TV.

• Check aerial connection.

Poor or no picture (screen is dark), good sound.

• Low picture settings. • Access the ‘Picture Adjustment’ menu and adjust the ‘Brightness’, ‘Colour’ and ‘Contrast’ settings. Refer to page 21.

No picture on any channel after digital tuning.

• No digital transmissions in your area.

• Weak signal.

• Unsuitable aerial.

• Tune in all available analogue channels. Refer to ‘Manual Programme Preset’ on page 25. Contact a local installer to find out when digital transmissions begin in your area.

• Ensure aerial/satellite dish is correctly aligned to transmitter.

• Ensure aerial is plugged directly into the TV (not through other equipment).

• Upgrade to a higher gain aerial.

• Upgrade to a higher gain aerial.

Some channels are blank. • Scrambled/Subscription only channel.

• Channel not being transmitted.

• Channel used only for data (no picture or sound).

• Subscribe to the pay-per-view service.

• Contact the broadcaster for transmission details

Standby indicator flashing. • Digital programme set for ‘Timer Record’ (regular flash).

• Fault (irregular flashing).

• Refer to ‘The Info menu’ on page 18.

• Do not open the cabinet, refer to qualified personnel.

• Contact your nearest Service Centre.

Good picture, no sound • Low or muted volume • Press the 2 + button on the remote control.

• If % is displayed, press the % button on the remote control.

No colour on colour programmes. • Low colour level settings. • Access the ‘Picture Adjustment’ menu and adjust the ‘Colour’ setting. Refer to page 21.

Remote control does not work. • Batteries low.

• Wrong mode selected

• Replace batteries.

• Press the MODE button repeatedly to select TV mode.

Distorted picture when changing programmes or selecting text.

• Connected equipment switched on. • Switch off external equipment (VCR, DVD player etc.)

• If you continue to have these problems, have your TV serviced by qualified personnel.

• NEVER open the casing yourself.


Additional Information 33

Indexi/Audio-out Vol., 22iDual Sound, 224:3 mode, 1114:9 mode, 10

AAccessories, supplied, 3Aerial, connecting, 4AI (Artificial Intelligence), Analogue channels, selecting, 5Audio option, 18Auto Format, 23Automatic tuning,

analogue and digital channels, 5, 24digital channels only, 19

Auto Vol. Control, 22AV3 Output, 23AV Preset, 24

BBalance, adjusting, 22Batteries, inserting into remote control, 3Brightness, adjusting, 6, 21 Buttons,

overview of the remote control, 7overview of the TV buttons, 8

CCategory pop-up list,14, 15Channel Index menu, 14Colour, adjusting, 6, 21 Colur Tone, 21Connecting,

an aerial, 4a VCR, 4 equipment to the TV, 28HD equipment, 28headphones, 27

Contrast,adjusting,6, 21

DDedicated digital text channels, 12Detail Set-up menu, 20Digital,

channels, selecting, 5Electronic Programme Guide, seeEPGsubtitles, 18text, 12timer see EPG

Dolby V mode, 6, 22DRC-MF, 21Dual Sound, 22Dynamic mode, 6, 22

RRecord (digital), 15, 16, 18Recording automatically, 16Remote control,

controlling a DVD player, 29controlling a VCR, 29inserting batteries, 3programming, 29overview, 7

Resetting,picture settings, 8, 21sound settings, 8

SSafety information, 2Selecting,

analogue mode, 5digital mode, 5

Serial number, finding, Inside front coverSet up menu, 24Screen mode, 10 Sharpness, adjusting, 6, 21Skipping a programme, 25Sleep Timer, 23Smart mode, 11Sound adjustment menu, 6, 22 Sound Effect, 6, 22Sound settings, adjusting, 6, 22 Specifications, 30Subtitles (digital), 18Supplied accessories, 3Switching on the TV, 5, 9System Information, 20

TTable of contents, 1Text,

analogue, 13digital, 12

Timed display, 15, 16Timer,

digital, cancelling, 16digital, setting manually, 16Sleep, 23

Troubleshooting, 31TV buttons, overview, 8TV menu system, 21Tuning,

automatic, 5manual (analogue channels), 25 manual (digital channels), 20

U, V, W, X, Y, ZVideo input button, 7, 8, 9Virtual Dolby, 22Virtual Effect, 22Volume, adjusting, 7, 8, 9 Wall paper, 19Wide mode, 10 Zoom mode, 10

E, FEveryday use, 9EPG, 15Equaliser Adjustment, 22Fastext, 13Favourite channels,

adding, 14removing, 14

Format Correction, 23Further Programme Preset menu, 25

G, H, I, J, KGame mode, 6, 21HD equipment, connecting, 28Headphones, connecting, 27Hue, adjusting, 21INFO menu, 18

L, M, NLive mode, 6, 21 Main Menu (digital), 19Manual Programme Preset menu, 25Manual Set Up menu, 24Manual timer, 16Manual tuning,

analogue channels, 25digital channels, 20

Mode button, 7 , 29Movie mode, 6, 21 Naming,

an analogue channel, 25an AV input, 24

Natural mode, 6, 22Noise Reduction, 21

OOn/Off button, 5, 8, 9Overview,

of the front sockets, 27of the rear sockets, 26of the remote control, 7of the TV buttons, 8

P, QParental control, 19Personal ID, Personal mode,

Picture, 6, 21 Sound, 6, 22

Picture Adjustment menu, 21Picture settings, adjusting, 6, 21 Picture Mode, 6, 21Picture Rotation, 24PIN Code, 20Power button, 5, 9Programme Index table, 7Programme,

labels (analogue), 24, 25naming (analogue), 24, 25sorting (analogue), 24skipping, 24

Sony Corporation Printed in UK

RecyclablePrinted on 100% recycled paper

KD-32NX200AUS

4-102-518-12(1)

410251812

Documents

Trinitron Integrated Digital Television - pro.sony