7/27/2019 TriMark Metalloy 80N1
1/2
METALLOY 80N1GAS-SHIELDED METAL-CORED WIRE 070814 (replaces
060911)AWS E80C-Ni1
Metalloy 80N1 is a gas-shielded metal-cored wire that is
designed for the single or multi-pass welding ofnickel-molybdenum
steels such as 1/2 Ni-1/4 Mo, 1 Ni-1/4 Mo, and 1-1/2 Ni-1/4 Mo.
Designed for use withargon gas mixtures, Metalloy 80 N1 is ideal
for welding castings, equipment and those applications requir-ing
toughness at sub-zero temperatures.
P RODUCT CHARACTERISTICS : Suitable for nickel-molybdenum
steels. High impacts at sub-zero temperatures. Single or
multiple-pass welding.
S PECIFICATIONS : E80C-Ni1 per AWS A5.28ABS Grade 3SA, 3YSACWB
E80C-Ni1 H8
S HIELDING GAS : 98% Ar/2% O 2, 75% Ar/25% CO 2, 35-50 cfh
WELDING P OSITIONS : CV Spray - flat, horizontal, vertical
downPulse and short arc - all positions
S TANDARD DIAMETERS : .045, .052, 1/16
TYPICAL UNDILUTED WELD METAL CHEMISTRY *: .
TYPICAL MECHANICAL P ROPERTIES *:98% Ar/2% O 2 75% Ar/25% CO
2
Tensile Strength 90,000 psi (621 MPa) 85,900 psi (593 MPa)Yield
Strength 77,000 psi (531 MPa) 74,000 psi (511 MPa)Elongation 26%
25%CVN @-50F (-46C) 46 ft lbs (62 J) 56 ft lbs (76 J)
*The information contained or otherwise referenced herein is
presented only as typical without guarantee orwarranty, and Hobart
Brothers Company expressly disclaims any liability incurred from
any reliance thereon. Typicaldata is obtained when welded and
tested in accordance with AWS A5.28 specification. Other tests and
proceduresmay produce different results. No data is to be construed
as a recommendation for any welding condition ortechnique not
controlled by Hobart Brothers Company.
C Mn Si Ni Mo98% Ar/2% O 2 0.04 1.14 0.40 0.97 0.12
75% Ar/25% CO 2 0.05 0.86 0.21 0.97 0.14
www.hobartbrothers.com400 Trade Square East
Troy, OH 45373PH: 1-800-424-1543FX: 1-800-541-6607
7/27/2019 TriMark Metalloy 80N1
2/2
RECOMMENDED OPERATING P ARAMETERS : The information below was
determined by welding performed with Ar/O 2 shielding gas at a flow
rate of35 cfh.
Bold: Optimum parameters for welder appeal.
Notice:Actual use of the product may produce varying results due
to conditions and welding techniques over which Tri-Mark has no
control,including, but not limited to, plate chemistry, weldment
design, fabrication methods, electrode size, welding procedure,
service re-quirements and environment. The purchaser is solely
responsible for determining the suitability of Tri-Mark products
for the pur-chasers own use. Any prior representations shall not be
binding. Tri-Mark disclaims any warranty of merchantability or
fitness forany particular purpose with respect to its products.
Caution:Consumers should be thoroughly familiar with the safety
precautions shown on the Warning Label posted on each shipment
inand in American National Standard Z49.1, Safety in Welding and
Cutting, published by the American Welding Society, 550 NW Le-Jeune
Road, Miami, FL 33126, and OSHA Safety and Health Standards 29 CFR
1910, available from the U.S. Department of Labor,Washington, D.C.
20210 .
Diameter,Electrical Stickout
(ES) Position
ArcVoltage(volts)
CurrentDCEP (+)
(amps)
Approx.Wire Feed Speed
(in/min)
DepositionRate
(lbs/hr)
.045 2732 35
200300 350
244455580
5.912.015.2
.052 273234
250350400
264439521
8.514.117.6
1/16 293234
300400450
256390464
11.217.620.9
METALLOY 80N1GAS-SHIELDED METAL-CORED WIRE
AWS E80C-Ni1
