Treatment - Hydro Technical Solutions - Product... · supermarkets transportation: carwash & auto detailing: food processing: pet care: ... current spikes and there are no reed switches

Wat

erTr

eatm

ent

Innovative

Dispensing

Solutions

Changing the World of Water Treatment Technology

While liquid chemicals remain the most popular solution, more and more water treatment specialists are turning to solid chemicals to treat the water in their boiler and cooling-tower systems.

Historically speaking, solid chemicals have played a prominent role in water treatment, specifically in the first half of the 20th century when they were used to prevent the corrosion and biological growth that could lead to catastrophic boiler failures.

By mid-century, however, liquid chemicals, buoyed by their ability to be easily blended, had replaced their solid counterparts.

While liquid chemicals remain the top choice among specialists, the tide appears to be turning back toward the use of solid chemicals for a number of important reasons; namely, the use of solid chemicals:

• Reduces shipping costs• Reduces inventory space• Reduces disposal costs• Eliminates drum-handling and disposal• Reduces caustic discharge to sewer systems• Reduces worker exposure to hazards• Increases energy-efficiency• Positions companies using them as environmentally

conscious “green” operators

TechnologySolid DissolversSolid Chemical is diluted by water sprayed up into an inverted bottle of chemical or the bottom of a chemical disk. This ‘make-up’ process leads to the dissolution of the solid chemical product and the filling of a reservoir with diluted chemical.

This diluted chemical is fed into the system from the reservoir. As the level of the reservoir lowers, so an integral primary float drops, triggering a primary solenoid valve which activates the water spray once again. The reservoir will then refill with diluted chemical raising the primary float until it reaches the shut-off point and closes the solenoid, thereby deactivating the spray.

This cycle will continue automatically dependant on demand in the system.

Installed directly in the water supply line, the injector operates without electricity, using water pressure as the power source.

The water drives the injector, which pulls the required percentage of concentrate directly from the chemical solution container. The concentrate is mixed with the water inside the pump and the water pressure forces the mixed solution downstream.

The injection ratio of chemical concentrate stays constant and accurate regardless of variations in flow or pressure.

The injection rate is set by lining up the top of the ratio sleeve with desired ratio on the scale. The amount of injected concentrate is proportional to the amount of water coming into the injector: i.e. adjustment at 1% = 1:100 = 1 volume of concentrate + 100 volumes of water entering the injector.

Piston

Oft

en

Use

d

schools universities

fast food facilities

fine dininghotels

& lodginghealthcare supermarkets transportation

carwash & auto detailing

food processing

pet care

Model Description

590GB Single product solid dissolver, float-activated, with primary reservoir and back-up float system/reservoir

• No electricity required• Runs off line water pressure (30-90 psi/2-6 bar)• Uses low cost, reliable float technology• Includes back-up reservoir and float assembly for

overflow protection• Includes adjustable pressure gauge and filter• Atmospheric siphon breaker included for backflow

protection• Translucent body allows viewing of water level in

reservoir• Takes advantage of the reduced transportation and

storage costs, and worker safety benefits of solid chemistry

The model 590 solid dissolver provides diluted solution of one product held in an integrated reservoir, ready for on demand pumping when indicated by the system controller. The system provides a backup sump/float system to prevent spills in case of an overflow condition.

USES RELIABLE, TIME-PROVEN FLOAT TECHNOLOGYNo electric solenoids to burn out, no transformers to fail when current spikes and there are no reed switches to gum up and stick.

EASY TO INSTALL4 bolt attachment, hook the float to the valve, attach the water inlet and the solution discharge tubing—that’s it.

INTEGRATED BACK-UP PROTECTIONThe unit contains a second reservoir and float assembly which is activated should the primary reservoir overflow. This back-up feature shuts off the water flow to prevent system overflow.DESIGNED FOR CHEMICAL RESISTANCEMoulded parts are made of polypropylene and polyethylene; metal parts are made of hastelloy for maximum chemical resistance.

SPECIALIZED NOZZLE TECHNOLOGYSpray nozzles are made from moulded polypropylene to avoid chemical attack. Four spray patterns are available to ensure optimum dissolve rates.

Oft

en

Use

d



fine dininghotels



food processing

pet care

Model Description

592GB High capacity, single product solid dissolver, sprays both product containers simultaneously

The High Output single solid dissolver provides diluted solution of one solid product (inhibitor or biocide) held in an integrated reservoir, ready for on-demand pumping when indicated by the system controller. Water sprays into both containers of the treatment product simultaneously for more rapid dissolving.

• No electricity required• Runs off line water pressure (30-90 psi/2-6 bar)• Uses low cost, reliable float technology• Includes back-up reservoir and float assembly for

overflow protection• Includes adjustable pressure gauge• Translucent body allows viewing of water level in



DESIGNED FOR CHEMICAL RESISTANCEMoulded parts are made of polypropylene and polyethylene; metal parts are made of Nitronic 50 steel for maximum chemical resistance.

INTEGRATED BACK-UP PROTECTIONThe unit contains a second reservoir and float assembly which is activated should the primary reservoir overflow. This back-up feature shuts off the water flow to prevent system overflow.

SPECIALIZED NOZZLE TECHNOLOGYSpray nozzles are moulded polypropylene to avoid chemical attack. Four spray patterns are available to ensure optimum dissolve rates.

TWO PRODUCT CONTAINERS EXTEND REPLACEMENT INTERVALBoth containers of the treatment product are sprayed simultaneously, allowing the reservoir to fill more quickly. In addition, the two containers allow replacement of product to be extended to double the time of single container units, for accounts with low visit frequency or high chemical use.

Oft

en

Use

d

594

593



fine dininghotels



food processing

pet care

Model Description

593GB Gravity-feed, one product solid dissolver, with 24, 115 or 230V solenoid

594GB Gravity-feed, one product solid dissolver, with timer

&

• Designed for “open” (non-pressurized) boiler feed tanks or towers

• Bowl and solenoid (or timer) mounted on panel for integrated functioning

• Runs off line water pressure (30-90 psi/2-6 bar)• 593 includes adjustable pressure gauge and filter• Atmospheric siphon breaker included for backflow

protection (593)

The solenoid-activated Gravity Feed system provides diluted solution of one solid product (inhibitor or biocide) as demanded by the system controller. The diluted solution is gravity-fed directly into the tower or boiler.


ECONOMICAL PERFORMANCEBy integrating components and using direct gravity-feed, the unit provides the lowest cost method of taking advantage of all of the benefits of solid chemistry.

SPECIALIZED SPRAY NOZZLE TECHNOLOGYSpray nozzles are moulded polypropylene to avoid chemical attack. Four spray patterns are available to ensure optimum dissolve rates.

TIME-BASED FEEDING (594)Select the times to feed chemical by programming the easy-to-use timer, which opens the water valve and sprays the solid chemical. No electricity required.

Oft

en

Use

d



fine dininghotels


carwash &auto detailing

foodprocessing

pet care

Model Description

595GB Single product solid dissolver, float-activated, with integrated reservoir

595GBCR Chlorine and Oxidising chemical resistant single product solid dissolver, float-activated, with integrated reservoir

• No electricity required• Runs off line water pressure (30-90 psi/2-6 bar)• Uses low cost, reliable float technology• Includes adjustable pressure gauge and filter• Atmospheric siphon breaker included for backflow

protection• Translucent body allows viewing of water level in



The 595 single solid dissolver provides diluted solution of one solid product held in an integrated reservoir, ready for on demand pumping when indicated by the system controller.

USES RELIABLE, TIME-PROVEN FLOAT TECHNOLOGYNo electric solenoids to burn out, no transformers to fail when current spikes and there are no reed switches to gum up and stick.


DESIGNED FOR CHEMICAL RESISTANCEMoulded parts are made of polypropylene and polyethylene; metal parts are made of NIT50 (GB) and hastelloy (GBCR) for maximum chemical resistance.

SPECIALIZED NOZZLE TECHNOLOGYSpray nozzles are moulded polypropylene to avoid chemical attack. Four spray patterns are available to ensure optimum dissolve rates.

Oft

en

Use

d



fine dininghotels



food processing

pet care

MULTI-DISK DESIGNThis unique design maintains a constant distance from the spray nozzle to the chemical surface delivering the consistent chemical concentrate on applications demand. The Multi-Disk design alsoallows you to load new disks at anytime - there’s no need to wait until the chemical container is empty.

NOW USE SOLIDS WITH LARGER ACCOUNTSThe ability to hold 20-40 lbs. (9-18kg) of chemical with one dissolver allows solids to be used on larger water treatment programs.

NO CHEMICAL CONTAINERBecause there is no container, there is no need to worry about when to change the container. Simply add more chemical disks during the normal service visit, or as needed.

Model Description

590MDGB Multi-Disk, single product solid dissolver, float-activated, back-up float system

592MDGB Multi-Disk, non-electric, continuous feed system

593MDGB Multi-Disk, gravity-feed, single product solid dissolver with solenoid

594MDGB Multi-Disk, gravity-feed, single product solid dissolver with timer

595MDGB Multi-Disk, single product solid dissolver, float-activated

• Allows dissolver to hold 20-40 lbs (9-18kg). of solid chemical

• Available as a stand-alone, or retrofit to any existing Hydro solid dissolver system

• Translucent cover for easy chemical level viewing• No electricity required• Translucent body allows viewing of water level in

reservoir• Take advantage of the reduced transportation and


The Multi-disk tower systems provide all of the benefits of the standard Hydro dissolvers plus the ability to add more chemical at any time and the ability to deliver more chemical between service visits. Choose this option when ordering your new dissolver, or retrofit your existing Hydro Systems Solid Dissolver to enhance the consistency of your water treatment regimen, and/or use solids at larger accounts.

Oft

en

Use

d


fast food fine dininghotels



food processing

pet care

• Advanced digital capabilities for greater efficiency and ease of use

• Flexibility for any configurations• A reputation for reliability• Unparalleled service

There is only one model of the Triton Cooling Tower controller. Equipped with 8 high capacity electro-mechanical relays, a sophisticated “all-in-one” flow switch, conductivity and temperature sensor and 8 fully configurable digital inputs.

Every Triton controller also comes with an Ethernet port and two front panel USB ports - one for data stick downloads and the other for easy local connection to a computer.

ONE-STEP DATA DOWNLOAD WITH USB “DATA STICK”Plug in a standard USB stick to download data, ready for you to analyse and graph.

OPEN, EXPANDABLE ARCHITECTURE WITH DIGITAL NETWORK Need more Relays? Need more Sensors? Need them far away from the main controller? Rejoice, with Triton’s digital expansion network, it is all “Plug’n’Play”!

FRONT PANEL “DIRECT ACCESS” BUTTONS Direct Access buttons enable navigation to main menu items with a single key stroke.

PRE-PROGRAMMED OPERATION MODES The controller is pre-programmed with simplified cooling tower water treatment programs for faster operation.Context-aware “Help” Key An integrated HELP button allows access to immediate, selection specific help information.

POWER FAILURE ALARM An interruption in AC power activates a visible warning light on the front panel. Alarm e-mails and SMS messages can also be sent to notify of power failure duration.

Oft

en

Use

d

Non-Electric, Fluid Driven Proportional Injector

horticulture animal health irrigationcarwash &

auto detailingindustrial

food processing

SuperDos operates without electricity to precisely inject liquid concentrates into a water supply line using fluid flow as the power source.

SuperDos is designed with a patented internal mixing chamber that promotes homogeneous mixing, while segregating harsh chemicals from critical internal components.

SuperDos comes in various models that easily satisfy the demands of your most challenging applications.

• No extra cost for proprietary composite body, which exceeds PVDF for chemical compatibility and for mixing aggressive chemicals.

• No extra cost for built-in on/off switch (30 and 45 models only), which allows user to stop the injection — but not the system.

• Separate internal mixing chamber to prevent chemical contact with motor piston — for longer life and uniform mixing.

• Interchangeable lower ends and can adjust ratios while in operation.

• Highly-aggressive, chemical-resistant models available• Diesel fuel-friendly models available

Principal applications

Chlorination, Cleaning, Cutting Fluids, Descaling, Decontamination, Degreasing, Disinfecting, Dispersants, Fertigation, Hydroponics, Inhibitors, Lubrication, Medication, Misting Systems, Odor Control, Pesticides, PH/TH Correction, Rinsing, Sanitizing, Soaps & Foams, Surfactants, Weed Control...

Basic installation

bypass installation

inline installationtank feed installation

dual remote injection installation

Operating principle

Installed directly in the water supply line, the injector operates without electricity, using water pressure as the power source. The water drives the injector, which pulls the required percentage of concentrate directly from the chemical solution container. Inside the patented mixing chamber the concentrate is mixed with the water and the water pressure forces the mixed solution downstream. The amount of concentrate will be directly proportional to the volume of water entering the injector, regardless of variations in flow or pressure.

Dilution

Model Model # Operating pressure (Bar) Water Flow (lit./hr) % Ratio

SuperDos 20 0.3% 113728RGB 0.34 - 6.9 34 - 4,500 0.025 - 0.3 1:4000 - 1:333

SuperDos 20 0.3% (Peracetic acid) 113728HAC 0.34 - 6.9 34 - 4,500 0.025 - 0.3 1:4000 - 1:333

SuperDos 20 2.5% 113705GB 0.34 - 6.9 34 - 4,500 0.2 - 2.5 1:500 - 1:40

SuperDos 20 2.5% WSP 113705WSPGB 0.34 - 6.9 34 - 4,500 0.2 - 2.5 1:500 - 1:40

SuperDos 20 5% 113706GB 0.34 - 6.9 34 - 4,500 0.4 - 5.0 1:250 - 1:20

SuperDos 20 10% 113707GB 0.34 - 4.5 34 - 3,000 2.0 - 10.0 1:50 - 1:10

SuperDos 30 0.3% (Peracetic acid) 113729K 0.34 - 6.9 34 - 6,800 0.025 - 0.3 1:4000 - 1:333

SuperDos 30 0.3% 113729RGB 0.34 - 6.9 34 - 6.800 0.025 - 0.3 1:4000 - 1:333

SuperDos 30 2.5% 113709GB 0.34 - 6.9 34 - 6.800 0.2 - 2.5 1:500 - 1:40

SuperDos 30 2.5% WSP 113709WSPGB 0.34 - 6.9 34 - 6.800 0.2 - 2.5 1:500 - 1:40

SuperDos 30 5% 113710GB 0.34 - 6.9 34 - 6.800 0.4 - 5.0 1:250 - 1:20

SuperDos 45 0.3% (Peracetic acid) 113730HAC 0.34 - 6.9 113 - 8,000 0.025 - 0.3 1:4000 - 1:333

SuperDos 45 0.3% 113730RGB 0.34 - 6.9 113 - 8,000 0.025 - 0.3 1:4000 - 1:333

SuperDos 45 2.5% 113712GB 0.34 - 6.9 113 - 8,000 0.2 - 2.5 1:500 - 1:40

SuperDos 45 5% 113715GB 0.34 - 5.5 113 - 8,000 0.4 - 5.0 1:250 - 1:20

Oft

en

Use

d

Non-Electric, Fluid Driven Proportional Injectors

Dilution

Model Model # Operating pressure (Bar) Water Flow (lit./hr.) % Ratio

MiniDos 0.4% 112609GB 0.5 - 9.5 30 - 2,500 0.025 - 0.4 1:4000 - 1:250

MiniDos 0.4% (Peracetic acid) 112609KGB 0.5 - 9.5 30 - 2,500 0.025 - 0.4 1:4000 - 1:250

MiniDos 1% 112601GB 0.5 - 9.5 30 - 2,500 0.2 - 1.0 1:500 - 1:100

MiniDos 2.5% 112603GB 0.5 - 9.5 30 - 2,500 0.5 - 2.5 1:200 - 1:40

MiniDos 5% 112605GB 0.5 - 9.5 30 - 2,500 1.0 - 5.0 1:100 - 1:20

MiniDos 10% 112607GB 0.5 - 4.5 30 - 2,200 2.0 - 10.0 1:50 - 1:10

MiniDos 20% 112621GB 0.5 - 4.5 30 - 1,600 4.0 - 20.0 1:25 - 1:5

• Propietary composite body, which exceeds PVDF for chemical compatibility and for mixing aggressive chemicals.

• Built-in on/off switch, which allows user to stop the injection, but not the system.

• Separate internal mixing chamber to prevent chemical contact with motor piston, for longer life and uniform mixing.

• Highest standard operating pressure in the industry, minimizing pressure surge damage.

MiniDos operates without electricity to precisely inject liquid concentrates into a water supply line using fluid flow as the power source.

MiniDos is designed with a patented internal mixing chamber that promotes homogeneous mixing, while segregating harsh chemicals from critical internal components.

irrigation vehicle care industryfood

processinghorticulture

Oft

en

Use

d

horticulture animal health irrigation vehicle care industryfood

processing

Dilution

Model Model # Operating pressure (Bar) Water Flow (lit./hr.) % Ratio

MicroDos 2% 116381GB 0.5 - 6.0 50 - 795 1 - 2.0 1:100 - 1:50

MicroDos 5% 116383GB 0.5 - 6.0 50 - 795 2.0 - 5.0 1:50 - 1:20

MicroDos 1% Fixed 116384GB 0.5 - 6.0 50 - 795 1.00 1:100



Principle applicationsDegreasing, Disinfecting, Dispersants, Inhibitors, Lubrication, Medication, Misting Systems, Odor Control, Pesticides, PH/TH Correction, Rinsing, Sanitizing, Soaps & Foams, Surfacatants, Weed Control

• No extra cost for proprietary composite body, which exceeds PVDF for chemical compatibility and for mixing aggressive chemicals.

• No extra cost for built-in on/off switch, which allows user to stop the injection—but not the system.

• Separate internal mixing chamber to prevent chemical contact with motor piston—for longer life and uniform mixing.

• Highest standard operating pressure in the industry, minimizing pressure surge damage.

MicroDos offers the widest range of models in the industry with flow rates from 7 l/h to 795 l/h and injection ratios from 0,5% to 10%.

In addition to our standard range of products for the Water Treatment industry, we also provide a comprehensive range of additional products and accessories as a distributor of Neptune Pumps and equipment.

The following pages are only a small selection of items available. Please contact us for further information on these and other products.

Accessories

Model Description

SOLENOID DRIVEN

PZ Basic model: manual type

PZD Basic model with digital panel

PZi4 Externally controlled type (input only)

PZi8 Externally controlled type (input & output)

PZiG Externally controlled type (input only)

AUTO FLOW CONTROL

PziA Externally controlled type (input & output)

• Manual control• Calibration function• Control input• Operation display• Signal input (4-pin connector)• Signal output (8-pin connector)• Alarms• Two point level control• Power supply for flow checker• Interval operation• Counter• Head can be turned 90° to allow base to be mounted

to a vertical wall

The PZ Series is the most flexible and accurate electronic diaphragm metering pump in the world!

• The PZD Series pumps offer higher capacities. These models feature an extra large keyboard and the injection rate can be entered directly in millilitres per minute.

• PZIG Models offer capacities typically requiring motor driven pumps. Special models easily handle viscosities of 1000 cP (up to 4000 cP at reduced volume). Powerful onboard controls allow proportional flow rate, pH and residual chlorine control by direct analog connection eliminating the PID Controller and Inverter (plus the control panel to house them), that are required by similar sized motor driven pumps.

MODEL APPROX. CAPACITY* MAX. PRESSURE SHIP WEIGHT

DBF-2HP 2 Gal / 7.5 L 300 psi / 20.7 bar 23 lbs / 10.4 Kg

DBFC-2 2 Gal / 7.5 L 300 psi / 20.7 bar 23 lbs / 10.4 Kg

DBF-5HP 5 Gal / 19 L 300 psi / 20.7 bar 38 lbs / 17.2 Kg

DBFC-5 5 Gal / 19 L 300 psi / 20.7 bar 38 lbs / 17.2 Kg

DBF-10HP 10 Gal / 38 L 300 psi / 20.7 bar 61 lbs / 27.6 Kg

MODEL APPROX. CAPACITY* MAX. PRESSURE SHIP WEIGHT

VTF-2HP 2 Gal / 7.5 L 300 psi / 20.7 bar 23 lbs / 10.4 Kg

VTF-5HP 5 Gal / 19 L 300 psi / 20.7 bar 37 lbs / 16.8 KG

VTF-10HP 10 Gal / 38 L 300 psi / 20.7 bar 60 lbs / 27.2 KG

VTF-12HP 2 Gal / 7.5 L 300 psi / 20.7 bar 68 lbs / 30.8 KG

VTF-2X4HP 5 Gal / 19 L 300 psi / 20.7 bar 23 lbs / 10.4 Kg

VTF-5X4HP 12 Gal / 42 L 300 psi / 20.7 bar 37 lbs / 16.8 KG

VTF-2-1 2 Gal / 7.5 L 300 psi / 20.7 bar 23 lbs / 10.4 Kg

VTF-5-1 5 Gal / 19 L 300 psi / 20.7 bar 37 lbs / 16.8 KG

* At 200°F / 93°C Max.

• Ideal for treating hot and chilled water circulating loops used in heating and air conditioning systems, process heating and cooling or large engine water jackets.

• Incorporates a high pressure cap rated to 300psi / 20.7 bar, offering better sealing with less force and eliminates the need for tools.

• Dish bottom in (DBF) and dish bottom out (VTF) versions available, as well as a Dish bottom in model incorporating a built-in support and mounting for a cartridge filter (DBFC).

• Filter bag kits can be added to VTF and DBF models to function simultaneously as a side stream filter.

• The “DBF” series features wide-mouth caps manufactured by Neptune. These caps utilize a square section “O” ring seal and will close easily by hand. Advantages of this series are demountable leg extensions and a full bottom drain. Optional Filter Bag Kit may be added.

• All Neptune By-Pass Feeders offer a quick opening, high pressure closure. These closures offer better sealing with less force and eliminate the need for tools.

By-Pass Feeders are a convenient method of introducing treatment chemicals into closed circulating water systems.

MODEL APPROX. CAPACITY* MAX. PRESSURE DIAM.

FTF-2HP 2 1/2 Gal / 9.5 L 300 psi / 20.7 bar 6” / 15.24 cm

FTF-2DB 2 Gal / 7.5 L 300 psi / 20.7 bar 6” / 15.24 cm

FTF-2CL 2 1/2 Gal / 9.5 L 300 psi / 20.7 bar 6” / 15.24 cm

FTF-5HP 7 1/2 Gal / 28 L 300 psi / 20.7 bar 10” / 25.4 cm

FTF-5DB 5 Gal / 19 L 300 psi / 20.7 bar 10” / 25.4 cm

FTF-5CL 7 1/2 Gal / 28 L 300 psi / 20.7 bar 10” / 25.4 cm

FTF-5150HP 7 1/2 Gal / 28 L 300 psi / 20.7 bar 10” / 25.4 cm

FTF-5150CL 57 1/2 Gal / 218 L 300 psi / 20.7 bar 10” / 25.4 cm

* At 200°F / 93°C Max.

Filter Feeders combine chemical addition and high capacity filtering in one piece of equipment. It is a convenient way to introduce solid or liquid chemicals into hot or cold water closed circulating systems.

• Stainless steel dissolving basket holds and fully supports the filter bag inside (order bag separately).

• Ring-top bags feature handles for easy removal.• “DB” type feeders have a full bottom drain and bolt on

legs with anchor bolt holes.• Model FTF-5150HP features oversize 11⁄2”inlet and

outlet connections. Can be used for system cleanup with high volume pumps where high flow rates are desired for fast clean-up or flush-out prior to start-up.

• “CL” Models feature a welded base to allow bolting to the floor or other mounting surface. Four holes for 3⁄8” bolts are provided on each Anchor Bolt Plate.

• Eliminates need for separate By-Pass Feeder and filter.• Filtration can be achieved at the same time as chemical

addition.• Extended neck with top inlet allows simple installation of

filter bag and basket.• Filter bags are available in 50, 20, 5 and 1 micron

ratings. (Order separately.)• Filter bags are quickly and easily replaced.

Office Locations

Hydro Systems Company3798 Round Bottom RoadCincinnatiOH 45244U.S.A.T 513-271-8800F 513-271-0160www.hydrosystemsco.com

Hydro Systems EuropeUnit 3, The Sterling CentreEastern RoadBracknell, BerkshireRG12 2PWEnglandT +44 (0)1344 488880F +44 (0)1344 488879www.hydrosystemseurope.com

Hydro Systems Europe13bis avenue DescartesC33370 Artigues-pres-BordeauxFranceT +33 557 97 13 13F +33 577 97 10 19

Hydro Systems South AmericaRua Mogiana, 172Chácaras ReunidasSão José Dos Campos12238-420SPBrasilT +55 12 3201 7707www.hydronovabrasil.com

Hydro Systems Asia PacificUnit A, 1 Kellham PlaceGlendenningNSW 2761AustraliaT +612 9625 8122F +612 9625 8177

Hydro Systems Asia Pacific Block #B, No. 51Mindong RoadPudong New AreaShanghai, PRC 201209T +86 21 61871037F +86 21 68727775

Dover Southeast Asia (Thailand) 762/2 , A Building, Room A540, Rama 3 Road,Bang Pong Pang, Yannawa,Bangkok 10120, ThailandT +66 2 295 2788F +66 2 295 2785

Documents

Treatment - Hydro Technical Solutions - Product... · supermarkets transportation: carwash & auto detailing: food processing: pet care: ... current spikes and there are no reed switches