Upload
shannon-glenn
View
225
Download
1
Tags:
Embed Size (px)
Citation preview
TRAMECHEAVY DUTY AIR BRAKE
HOSE ASSEMBLIES
TRAMECHEAVY DUTY AIR BRAKE
HOSE ASSEMBLIES
• Meets DOT 106 & SAE J1402
• Both Ends Swivel After Installation
• Factory or Field Assembly
• Non-Corrodable Parts in the Air Path
• Meets DOT 106 & SAE J1402
• Both Ends Swivel After Installation
• Factory or Field Assembly
• Non-Corrodable Parts in the Air Path
ConstructionConstructionReinforced Nylon Tube Supports HoseReinforced Nylon Tube Supports Hose
O-Ring Seals Air & Allows Swivel (-60°F)O-Ring Seals Air & Allows Swivel (-60°F)
Brass Fitting Provides “Live Swivel” Fitting Is Retained By Tube & ShellBrass Fitting Provides “Live Swivel” Fitting Is Retained By Tube & Shell
Reinforced Nylon Shell Provides Consistent Compression of Hose to Seal on the TubeReinforced Nylon Shell Provides Consistent Compression of Hose to Seal on the Tube
Plated Steel Ring Defines Outside Diameter Plated Steel Ring Defines Outside Diameter
Standard SAE J1402 Air Brake HoseStandard SAE J1402 Air Brake Hose
ConventionalCrimped StyleConventionalCrimped Style
TRAMEC “Live Swivel” FittingTRAMEC “Live Swivel” Fitting
Eliminates Swivel Adapters Both Ends Swivel Eases Installation
Eliminates Swivel Adapters Both Ends Swivel Eases Installation
Reduces Stress on Hose Material Extends Hose LifeReduces Stress on Hose Material Extends Hose Life
Assembly ConfidenceAssembly Confidence
Molded Shell & Tube Define Squeeze Hose Compression Not Subject to Operator Set Up
Molded Shell & Tube Define Squeeze Hose Compression Not Subject to Operator Set Up
ConventionalCrimped StyleConventionalCrimped Style
Molded Shell & Ring Design Allows Visual Inspection of Hose Insertion Depth
Molded Shell & Ring Design Allows Visual Inspection of Hose Insertion Depth
Assembly ConfidenceAssembly Confidence
Fitting StyleFitting Style
14.914.5
19.314.5
14.914.5
19.314.5
Average Impact HtAt Failure
Average Impact HtAt Failure
3/8” Live Swivel3/8” Crimped
1/2” Live Swivel1/2” Crimped
3/8” Live Swivel3/8” Crimped
1/2” Live Swivel1/2” Crimped
In addition to exceeding all DOT & SAE requirements for tensile, burst, flexural, temperature, etc. The TRAMEC live swivel has demonstrated that it is as least as strong as the conventional fitting in resisting side impact (no DOT requirement).
In addition to exceeding all DOT & SAE requirements for tensile, burst, flexural, temperature, etc. The TRAMEC live swivel has demonstrated that it is as least as strong as the conventional fitting in resisting side impact (no DOT requirement).
Repeated impacts by a weight dropped from increasing heights, while at 150 psi.
Repeated impacts by a weight dropped from increasing heights, while at 150 psi.
TRAMEC “Live Swivel” FittingTRAMEC “Live Swivel” Fitting
Available for3/8” I.D. ...Available for3/8” I.D. ...
And for 1/2” I.D.Air Brake HosesAnd for 1/2” I.D.Air Brake Hoses
TRAMEC “Live Swivel” FittingTRAMEC “Live Swivel” Fitting
In Kits for3/8” I.D. Hose
In Kits for3/8” I.D. Hose
… or Bulk Packed for3/8” & 1/2” I.D. Hose… or Bulk Packed for3/8” & 1/2” I.D. Hose