Flow Measurement Training CenterMicro Motion Coriolis Technician Course (#2359)

Copyright © 2012 by Emerson Process Management Flow BV. All r ights r eserved. N o par t o f t his publication may be r eproduced, s tored i n a retrieval system, or t ransmitted in any way or by any means, including, without limitation, ph otocopying or r ecording, without t he pr ior w ritten c onsent o f Emerson Process Management Flow BV. Important Notices The material c ontained i n t his pu blication ( including any s upplementary information) constitutes and c ontains confidential and proprietary information of Emerson Process Management Flow BV. By gaining access to the attached, you acknowledge and agree that the material (including any modification, translation or adaptation of the material) and all copyright, trade secrets and all other right, title and interest therein, are the sole property of Emerson Process Management Flow BV.

Although Emerson Process Management Flow has taken due care to ensure that the material included in this publication is accurate and complete. Emerson Process Management Flow cannot warrant that the information contained in this publication is complete, does not contain typographical or other errors, or will meet your specific requirements. As such, Emerson Process Management Flow does not assume and hereby disclaims all liability, consequential or otherwise, for any loss or damage to any person or entity which is caused by or relates to errors or omissions in this publication (including any supplementary information), whether such errors or omissions result from negligence, accident or any other cause.

Emerson Process Management Flow BV Neonstraat 1 6718 WX Ede The Netherlands Telephone: +31 (0)318 495 431 FAX: +31 (0)318 495 439 For additional course information contact: Customer Training / Arnoud Hazelaar Emerson Process Management Flow BV Telephone: +31 (0)318 495 446 E-mail: Flowtraining@emerson.com

Agenda: Rosemount Magmeter TechnicianAgenda: Rosemount Magmeter Technician1 Day training for TechniciansCourse #2340

Course ObjectivesCourse Objectives

� After this course you will be able to:– Understand the design, construction and operation of Rosemount

Magnetic flow meters.

– Correctly install, configure, operate and maintain the flow metering system.

– Perform troubleshooting and diagnostic procedures.

– Use Configuration Tools such as AMS.

[File Name or Event]Emerson Confidential27-Jun-01, Slide 2

– Use Configuration Tools such as AMS.

Rosemount Magmeter TechnicianRosemount Magmeter Technician08:30 hr. Magmeter Flow Technology09:15 hr. Magmeter Products & Features10:15 hr. Break10:30 hr. Demo: High Process Noise11:00 hr. Magmeter Installation & Start-up 12:00 hr. Lunch13:00 hr. Exercise: Simulation & Trimming Magmeter14:00 hr. Exercise: Configuration & Calibration Magmeter

[File Name or Event]Emerson Confidential27-Jun-01, Slide 3

14:00 hr. Exercise: Configuration & Calibration Magmeterwith AMS

14:45 hr. Break15:00 hr. Exercise: Diagnostics of a Magmeter with AMS16:00 hr. Magmeter Troubleshooting16:30 hr. Evaluation16:45 hr. End of training

General InformationThe Micro Motion Coriolis Technician course offered by Emerson Process Management Flow is a 2-day course. It is specifically designed for your technicians who are involved in the installation, commissioning, maintenance or use of Micro Motion mass flow meter and offered in the following languages: English, German, French or Dutch.

Emerson Process Management Flow provides a variety of flow training courses on the Micro Motion range of Coriolis flow and density meters and the Rosemount Vortex and Magnetic flow meters.

Course OverviewThe course covers Coriolis flow meter operat-ing principles and capabilities; how to install, commission, operate and troubleshoot this equipment. During this training, your plant personnel will learn how to reduce start-up time, plant downtime, even reduce spares inventory and thereby maximize the utilization of your flow meter investment.

The course is structured with one goal in mind: to ensure that your technicians gain the high-est level of flow meter knowledge and skills, ensuring maximum plant productivity.

Practical Training“I hear and I forget; I see and I remember; I do and I understand.” This quote is usually attributed to Confucius, the Chinese philosopher (550 BC). Therefore each training course consists of both theory and hands-on activities.

The practical training In Ede (The Netherlands) is centered around Flow loops simulating a plant environment. Trainees will configure and calibrate several Flow measurement instruments thus helping their understanding of the theoretical principles involved.

Micro Motion Coriolis Technician Course2 Day Course (#2359)

F L O W M E A S U R E M E N T T R A I N I N G C E N T E R

Leading

in Learning

E M E R S O N . C O N S I D E R I T S O L V E D .

Where our Flow knowledge and learning come together

TrainersThe course will be presented by Emerson trainers, who are certified on both industry application knowledge and teaching ability. Each trainer has considerable experience gained from working in the field as a Service Engineer or Applications Engineer.

Empower your Technical StaffToo often, troubleshooting is one of the most unproductive and frustrating tasks maintenance people face. Therefore your technical staff will benefit from professional, up-to-date “hands-on” training encompassing the use of specialised tools.

Trainees who complete this course will be able to:• Understand the design, construction and operation of Micro Motion meters• Correctly install, configure, operate and maintain the flow metering system• Perform troubleshooting and diagnostic procedures

Course ParticipationWe offer two options for course participation: Dedicated group course or open registration.

Course FeesOpen Registration € 1110 plus VAT per registrant.This includes participation on the course, lecture notes, lunch and refreshments each day,To maximise learning, classes are limited in size up to a maximum of 8 trainees.

Open Registration Course Dates2013: 27-28 February, 5-6 June, 11-12 SeptemberModel Code: MMIYCT7B2EDE21DN0ECSA

For more information, please contactFlow Training Center Tel.: +31 (0)318 495 446, E-mail: Flowtraining@Emerson.com

Emerson Process Management FlowNeonstraat 1 6718 WX Ede The Netherlands +31 (0)318 495 555

Leading

in Learning

General InformationThe Micro Motion Coriolis Technician course offered by Emerson Process Management Flow is a 2-day course. It is specifically designed for your technicians who are involved in the installation, commissioning, maintenance or use of Micro Motion mass flow meter and offered in the following languages: English, German, French or Dutch.

Emerson Process Management Flow provides a variety of flow training courses on the Micro Motion range of Coriolis flow and density meters and the Rosemount Vortex and Magnetic flow meters.

Course OverviewThe course covers Coriolis flow meter operat-ing principles and capabilities; how to install, commission, operate and troubleshoot this equipment. During this training, your plant personnel will learn how to reduce start-up time, plant downtime, even reduce spares inventory and thereby maximize the utilization of your flow meter investment.

The course is structured with one goal in mind: to ensure that your technicians gain the high-est level of flow meter knowledge and skills, ensuring maximum plant productivity.

Practical Training“I hear and I forget; I see and I remember; I do and I understand.” This quote is usually attributed to Confucius, the Chinese philosopher (550 BC). Therefore each training course consists of both theory and hands-on activities.

The practical training In Ede (The Netherlands) is centered around Flow loops simulating a plant environment. Trainees will configure and calibrate several Flow measurement instruments thus helping their understanding of the theoretical principles involved.

Micro Motion Coriolis Technician Course2 Day Course (#2359)

F L O W M E A S U R E M E N T T R A I N I N G C E N T E R

Leading

in Learning

E M E R S O N . C O N S I D E R I T S O L V E D .

Where our Flow knowledge and learning come together

TrainersThe course will be presented by Emerson trainers, who are certified on both industry application knowledge and teaching ability. Each trainer has considerable experience gained from working in the field as a Service Engineer or Applications Engineer.

Empower your Technical StaffToo often, troubleshooting is one of the most unproductive and frustrating tasks maintenance people face. Therefore your technical staff will benefit from professional, up-to-date “hands-on” training encompassing the use of specialised tools.

Trainees who complete this course will be able to:• Understand the design, construction and operation of Micro Motion meters• Correctly install, configure, operate and maintain the flow metering system• Perform troubleshooting and diagnostic procedures

Course ParticipationWe offer two options for course participation: Dedicated group course or open registration.

Course Fees € 2220,- plus VAT per day.This includes participation on the course, lecture notes, lunch and refreshments each day.To maximise learning, classes are limited in size up to a maximum of 8 trainees.

Course Dates 2013Please contact us for available datesModel Code: MMIYCT1B1EDE28D0N0ECSA

For more information, please contactFlow Training Center Tel.: +31 (0)318 495 446, E-mail: Flowtraining@Emerson.com

Emerson Process Management FlowNeonstraat 1 6718 WX Ede The Netherlands +31 (0)318 495 555

Leading

in Learning

Agenda: Rosemount Magmeter TechnicianAgenda: Rosemount Magmeter Technician1 Day training for TechniciansCourse #2340

Course ObjectivesCourse Objectives

� After this course you will be able to:– Understand the design, construction and operation of Rosemount

Magnetic flow meters.

– Correctly install, configure, operate and maintain the flow metering system.

– Perform troubleshooting and diagnostic procedures.

– Use Configuration Tools such as AMS.

[File Name or Event]Emerson Confidential27-Jun-01, Slide 2

– Use Configuration Tools such as AMS.

Rosemount Magmeter TechnicianRosemount Magmeter Technician08:30 hr. Magmeter Flow Technology09:15 hr. Magmeter Products & Features10:15 hr. Break10:30 hr. Demo: High Process Noise11:00 hr. Magmeter Installation & Start-up 12:00 hr. Lunch13:00 hr. Exercise: Simulation & Trimming Magmeter14:00 hr. Exercise: Configuration & Calibration Magmeter

[File Name or Event]Emerson Confidential27-Jun-01, Slide 3

14:00 hr. Exercise: Configuration & Calibration Magmeterwith AMS

14:45 hr. Break15:00 hr. Exercise: Diagnostics of a Magmeter with AMS16:00 hr. Magmeter Troubleshooting16:30 hr. Evaluation16:45 hr. End of training

General InformationThe Rosemount Magmeter Technician course offered by Emerson Process Management Flow is a 1-day course. It is targeted for technicians, instrument engineers and operators who are involved with the installation, commissioning, use and maintenance of Rosemount Magmeters. Emerson Process Management Flow provides a variety of flow training courses on the Micro Motionrange of Coriolis flow and density meters and the Rosemount Vortex and Magnetic flow meters.

Course OverviewThis course covers the Magmeter’s operating principles, its installation, configuration and troubleshooting. Consisting of both theory and hands-on activities, the practical training is centered around mobile flowloops with Magmeters installed.

During this training, your plant personnel will learn how to reduce start-up time, plant downtime, even reduce spares inventory and thereby maximize the utilization of your flow meter investment.

The course is structured with one goal in mind: to ensure that your technicians gain the highest level of flow meter knowledge and skills, ensuring maximum plant productivity.

Practical Training“I hear and I forget; I see and I remember; I do and I understand.” This quote is usually attributed to Confucius, the Chinese philosopher (550 BC). Therefore each training course consists of both theory and hands-on activities. The practical training is centered around special designed Flow loops, simulatinga plant environment. Trainees will configure and calibrate several Flow measurement instruments thus helping their understanding of the theoretical principles involved.

Rosemount Magmeter Technician Course1 Day Course (#2340)

F L O W T R A I N I N G C E N T E RLeading

in Learning

E M E R S O N . C O N S I D E R I T S O L V E D .

Where our Flow knowledge and learning come together

TrainersThe course will be presented by Emerson trainers, who are certified on both industry application knowledge and teaching ability. Each trainer has considerable experience gained from working in the field as a Service Engineer or Applications Engineer.

Empower your Technical StaffDuring the course of this training, your technical staff will benefit from professional, up-to-date “hands-on” training encompassing the use of specialised tools.

Trainees who complete this course will be able to:• Understand the design, construction and operation of Rosemount Magmeters• Correctly install, configure, operate and maintain the flow metering system• Perform troubleshooting and diagnostic procedures

Course FeesOpen Registration - € 555 plus VAT per registrant.This includes participation on the course, lecture notes and lunch and refreshments each day.To maximise learning, classes are limited in size up to a maximum of 8 trainees.

LocationThe Open Registration trainingen will take place in the Flow Training Center in Ede, The Netherlands. Emerson has special price agreements with serveral hotels in the area; we are pleased to assist you with booking a hotel.

Course Dates 2012/20133 December, 25 Februari, 3 June, 9 SeptemberModel Code: RFDYCT8B2EDEB1D0N0ECSA

For more information, please contactFlow Training Center, tel: +31 (0)318 495 446, Flowtraining@Emerson.com

Emerson Process Management FlowNeonstraat 1 6718 WX Ede The Netherlands +31 (0)318 495 555

Leading

in Learning

General InformationThe Rosemount Magmeter Technician course offered by Emerson Process Management Flow is a 1-day course. It is targeted for technicians, instrument engineers and operators who are involved with the installation, commissioning, use and maintenance of Rosemount Magmeters. Emerson Process Management Flow provides a variety of flow training courses on the Micro Motionrange of Coriolis flow and density meters and the Rosemount Vortex and Magnetic flow meters.

Course OverviewThis course covers the Magmeter’s operating principles, its installation, configuration and troubleshooting. Consisting of both theory and hands-on activities, the practical training is centered around mobile flowloops with Magmeters installed.

During this training, your plant personnel will learn how to reduce start-up time, plant downtime, even reduce spares inventory and thereby maximize the utilization of your flow meter investment.

The course is structured with one goal in mind: to ensure that your technicians gain the highest level of flow meter knowledge and skills, ensuring maximum plant productivity.

Practical Training“I hear and I forget; I see and I remember; I do and I understand.” This quote is usually attributed to Confucius, the Chinese philosopher (550 BC). Therefore each training course consists of both theory and hands-on activities. The practical training is centered around special designed Flow loops, simulatinga plant environment. Trainees will configure and calibrate several Flow measurement instruments thus helping their understanding of the theoretical principles involved.

Rosemount Magmeter Technician Course1 Day Course (#2340)

F L O W T R A I N I N G C E N T E RLeading

in Learning

E M E R S O N . C O N S I D E R I T S O L V E D .

Where our Flow knowledge and learning come together

TrainersThe course will be presented by Emerson trainers, who are certified on both industry application knowledge and teaching ability. Each trainer has considerable experience gained from working in the field as a Service Engineer or Applications Engineer.

Empower your Technical StaffDuring the course of this training, your technical staff will benefit from professional, up-to-date “hands-on” training encompassing the use of specialised tools.

Trainees who complete this course will be able to:• Understand the design, construction and operation of Rosemount Magmeters• Correctly install, configure, operate and maintain the flow metering system• Perform troubleshooting and diagnostic procedures

Course FeesDedicated Group €2220 plus VAT per day. This includes participation on the course, lecture notes and lunch and refreshments each day.To maximise learning, classes are limited in size up to a maximum of 8 trainees.

Course Dates 2013Please contact us for availabale dates.Product Code: RFDYCT2B1EDEC8D0N0ECSA

For more information, please contactFlow Training Center, tel: +31 (0)318 495 446, Flowtraining@Emerson.com

Emerson Process Management FlowNeonstraat 1 6718 WX Ede The Netherlands +31 (0)318 495 555

Leading

in Learning

Agenda: Rosemount Vortex TechnicianAgenda: Rosemount Vortex Technician1 Day training for Technicians and EngineersCourse #2341

Course ObjectivesCourse Objectives� After this course you will be able to:

– Understand the design, construction and operation of Rosemount Vortex flow meters

– Correctly install, configure, operate and maintain the flow metering system

– Perform troubleshooting and diagnostic procedures– Use Configuration Tools such as AMS

[File Name or Event]Emerson Confidential27-Jun-01, Slide 2

Vortex Technician TrainingVortex Technician Training09:00 hr. Vortex Flow Technology

(Principle of operation, design & installation)

10:30 hr. Break

10:45 hr. Rosemount Vortex Model 8800 Overview

11:00 hr. Vortex Signal Processing

12:00 hr. Lunch

13:00 hr. Excercise: Build a Vortex Meter

[File Name or Event]Emerson Confidential27-Jun-01, Slide 3

13:00 hr. Excercise: Build a Vortex Meter

13:45 hr. Vortex Flow meter Configuration Parameters

14:45 hr. Vortex Start-Up

15:15 hr. Break

15:30 hr. Vortex Flow meter Troubleshooting

16:15 hr. Exercise: Vortex Configuration

17:00 hr. End of Training

General InformationThe Rosemount Vortex Technician course offered by Emerson Process Management Flow is a 1-day course. It is specifically designed for your technicians and engineers who are involved in the installation, commissioning, maintenance or use of Rosemount Vortex flow meters. The course can be delivered in the following languages: English, German, French or Dutch.

Emerson Process Management Flow provides a variety of flow training courses on the Micro Motion range of Coriolis flow and density meters and the Rosemount Vortex and Magnetic flow meters.

Course OverviewThe course covers Vortex flow meter operating principles and capabilities; how to install, commission, operate and troubleshoot this equipment.

During this training, your plant personnel will learn how to reduce start-up time, plant downtime, even reduce spares inventory and thereby maximize the utilization of your flow meter investment.

The course is structured with one goal in mind: to ensure that your technicians gain the highest level of flow meter knowledge and skills, ensuring maximum plant productivity. Practical Training“I hear and I forget; I see and I remember; I do and I understand.” This quote is usually attributed to Confucius, the Chinese philosopher (550 BC). Therefore each training course consists of both theory and hands-on activities.

The practical training In Ede (The Netherlands) is centered around Flow loops simulating a plant environment. Trainees will configure and calibrate several Flow measurement instruments thus helping their understanding of the theoretical principles involved.

Rosemount Vortex Technician Course1 Day Course (#2341)

F L O W T R A I N I N G C E N T E RLeading

in Learning

E M E R S O N . C O N S I D E R I T S O L V E D .

Where our Flow knowledge and learning come together

TrainersThe course will be presented by Emerson trainers, who are certified on both industry application knowledge and teaching ability. Each trainer has considerable experience gained from working in the field as a Service Engineer or Applications Engineer.

Empower your Technical StaffDuring the course of this training, your technical staff will benefit from professional, up-to-date “hands-on” training encompassing the use of specialised tools.

Trainees who complete this course will be able to:• Understand the design, construction and operation of Rosemount Vortex meters• Correctly install, configure, operate and maintain the flow metering system• Perform troubleshooting and diagnostic procedures

Course ParticipationWe offer two options for course participation: Dedicated group course or open registration.

LocationThe Open Registration trainingen will take place in the Flow Training Center in Ede, The Netherlands. Emerson has special price agreements with serveral hotels in the area; we are pleased to assist you with booking a hotel.

Course Fees€ 2220,- per day. This includes participation on the course, lecture notes, lunch and refreshments.. To maximise learning, classes are limited in size up to a maximum of 8 trainees.

Course Dates 2013Please contact us for availabale dates.Model Code: RFDYCT2A1EDE18D0N0ECSA

For more information, please contactFlow Training Center, tel: +31 (0)318 495 446, Flowtraining@Emerson.com

Emerson Process Management FlowNeonstraat 1 6718 WX Ede The Netherlands +31 (0)318 495 555

Leading

in Learning

General InformationThe Rosemount Vortex Technician course offered by Emerson Process Management Flow is a 1-day course. It is specifically designed for your technicians and engineers who are involved in the installation, commissioning, maintenance or use of Rosemount Vortex flow meters. The course can be delivered in the following languages: English, German, French or Dutch.

Emerson Process Management Flow provides a variety of flow training courses on the Micro Motion range of Coriolis flow and density meters and the Rosemount Vortex and Magnetic flow meters.

Course OverviewThe course covers Vortex flow meter operating principles and capabilities; how to install, commission, operate and troubleshoot this equipment.

During this training, your plant personnel will learn how to reduce start-up time, plant downtime, even reduce spares inventory and thereby maximize the utilization of your flow meter investment.

The course is structured with one goal in mind: to ensure that your technicians gain the highest level of flow meter knowledge and skills, ensuring maximum plant productivity. Practical Training“I hear and I forget; I see and I remember; I do and I understand.” This quote is usually attributed to Confucius, the Chinese philosopher (550 BC). Therefore each training course consists of both theory and hands-on activities.

The practical training In Ede (The Netherlands) is centered around Flow loops simulating a plant environment. Trainees will configure and calibrate several Flow measurement instruments thus helping their understanding of the theoretical principles involved.

Rosemount Vortex Technician Course1 Day Course (#2341)

F L O W T R A I N I N G C E N T E RLeading

in Learning

E M E R S O N . C O N S I D E R I T S O L V E D .

Where our Flow knowledge and learning come together

TrainersThe course will be presented by Emerson trainers, who are certified on both industry application knowledge and teaching ability. Each trainer has considerable experience gained from working in the field as a Service Engineer or Applications Engineer.

Empower your Technical StaffDuring the course of this training, your technical staff will benefit from professional, up-to-date “hands-on” training encompassing the use of specialised tools.

Trainees who complete this course will be able to:• Understand the design, construction and operation of Rosemount Vortex meters• Correctly install, configure, operate and maintain the flow metering system• Perform troubleshooting and diagnostic procedures

Course ParticipationWe offer two options for course participation: Dedicated group course or open registration.

LocationThe Open Registration trainingen will take place in the Flow Training Center in Ede, The Netherlands. Emerson has special price agreements with serveral hotels in the area; we are pleased to assist you with booking a hotel.

Course FeesOpen Registration - €555 plus VAT per registrant.This includes participation on the course, lecture notes, lunch and refreshments. To maximise learning, classes are limited in size up to a maximum of 8 trainees.

Course Dates 2012/20134 December, 26 Februari, 4 June, 10 SeptemberModel code: RFDYCT8A2EDE11D0NNECSA

For more information, please contactFlow Training Center, tel: +31 (0)318 495 446, Flowtraining@Emerson.com

Emerson Process Management FlowNeonstraat 1 6718 WX Ede The Netherlands +31 (0)318 495 555

Leading

in Learning

Process Instrumentation Training Europe Instrumentation training capabilities

Empower your Staff

Striving to optimize plant operation, reduce start-up time, plant down time and even reduce spares inventory? We can help.

Looking for a training that teaches your staff process instrumentation operating principles and capabilities? We can help.

Developing skilled maintenance professionals who understand operating principles and capabilities of process instrumentation and know how to install, commission, operate, and troubleshoot the equipment? We can help.

How can we help? Our instrumentation Training programs are structured with one goal in mind: to ensure your engineers and technicians gain the highest level of process instrumentation knowledge and skills. This approach empowers your staff to maximize your overall plant productivity and profitability.

Process Instrumentation Training

Emerson Process Management offers a wide range of technologies, products and services to customers around the world. With its Rosemount and Micro Motion brands, Emerson delivers high quality measurement devices for flow, pressure, temperature, level, wireless, density, and viscosity applications.

Emerson Instrumentation Training Centres are designed to ensure you get maximum value out of each of your instruments. The Training Centres focus on teaching fundamental, theoretical, and practical knowledge on a range of process applications. The capabilities of instrumentation technologies are designed for these application challenges.

Emerson offers professional courses to a variety of professionals:

• Service and maintenance technicians• Instrumentation and process engineers• Engineering contractors• Graduates and new hires

We offer flexibility regarding location, training dates, languages and course content.

2

33

“Excellent course, focused on our requirements.”

M. Stroud (Kodak, UK)

An Approach to Innovative Training

Our process instrumentation training is specifically designed for today’s industrial engineer or plant worker with a focus on interaction and a blend of different types of learning methods. Lessons use animations, graphics, audio, video and interactive exercises to augment and intensify the entire learning experience. By focusing on the principles of see, hear, read, and do, the courses encourage interactive learning and stimulate interest.

Each training course consists of both theory and hands-on activities while providing practical interaction with a range of devices. Trainees will configure and calibrate several measurement instruments thus helping their understanding of the theoretical principles involved

Each training course experience centers around the Emerson flow loops which simulate an actual plant environment. Students are able to see the wide breadth of Emerson technologies in applications and learn how devices operate under various conditions. Specially designed, portable demonstration units are also available to effectively perform practical on-site training sessions at customer facilities or plants.

Classes are restricted to a maximum of eight trainees. This way, trainees benefit from the positive learning atmosphere and get sufficient attention from the instructors.

3

“Very informative. Good mixture of technical and practical training.”

V. Latto (Metco, Scotland)

44

Measurement Technology Training

Engineers are often faced with challenging applications for which they have to select between different technologies. Given the vast range of measurement technologies, engineers can therefore benefit from our professional, up-to-date hands-on training, encompassing the use of modern instrumentation.

Measurement Technology Training is designed for those interested in understanding the principles of various measurement technologies, or those involved in specifying, choosing, and applying instrumentation. The courses provide an in-depth look at both the operational aspect of devices and the appropriateness of various technologies to defined applications.

Individual courses are available that cover basic measurement technology with a choice of flow, level, pressure, temperature and wireless.

Instrumentation Maintenance Training

Troubleshooting can be one of the most frustrating tasks maintenance employees face. In order to resolve an issue, vast knowledge is required to understand complex process devices.

Instrumentation Maintenance Training is designed for service and maintenance personnel. Trainees will benefit from up-to-date “hands-on” training using actual devices and specialized tools. These comprehensive courses cover instrumentation operating principles and capabilities, installation, calibration, configuration, troubleshooting, repair, and preventive maintenance.

Individual courses are available, addressing instrumentation maintenance with a choice of training for flow, level, pressure, temperature, wireless, density, and viscosity devices and digital communication protocols.

Courses Course Topics

Training courses focus on the areas of Measurement Technologies and Instrumentation Maintenance. The topics are targeted at various audiences and provide unique learning objectives.

55

Course Formats

We realize that everyone learns in a different manner. To tailor the training to your needs, we offer you the following options:

• Instructor Led Training - Dedicated Class • Instructor Led Training - Open Registration Class • Online Training Instructor Led Training – Dedicated Class

Many of our classes are taught via the traditional Instructor-Led format, entirely customized to your requirements and held for a group of participants. This format is particularly valuable for your company when more than one person is interested in a specific training. We can offer courses based on predefined Emerson training modules, add specific topics, or even develop entirely customized content. Location and training dates will also be decided upon together with you.

The training can be delivered in different European languages, please contact us for all available options.

Instructor Led Training – Open Registration Class

Some courses are also available for Open Registration. Here participants have the opportunity to meet users from different industries. The content of the training is pre-determined and Emerson decides on the best suitable training, dates and location.

The language will primarily be English, but could also be subject to local requirements. For available locations and dates, please contact the relevant training centre.

Online Training

Online learning is an excellent way to help manage your time and costs when you can not attend a regional or local training session. Online training is offered as Instructor-Led or Self-Paced - it’s your choice.

For more information about our online training offerings please contact the relevant training centre.

“The instructors knew what they were talking about and answered all my questions.”

P. Odendaal (Sasol Oil, South Africa)

5

6

Quality Focus for Maximum Results

Emerson is committed to delivering a quality experience to participants in the training program. This quality approach extends to instructors, environments and learning materials.

Certified Instructors

All Emerson instructors are certified on both product and application knowledge as well as teaching ability. Each instructor is a technical expert and can offer considerable field experience from working in the field as a Service & Application Engineer or Product Specialist.

Training Locations

Trainees can attend courses at one of our European Instrumentation Training Centres or participate in one of the classes we conduct at a local sales or service office. Training classes typically start at 08:30h and end at 17:00h. Lunch and refreshments are provided in our company restaurant or in our training centre.

Emerson also offers on-site training courses subject to available facilities and full scope required.

Course materials

Course materials will be provided, including paper copies of all presentations. A certificate of attendance is awarded to all participants who have completed at least 80% of the course; it is also possible to include a post test on the final day of the training.

6

“We would recommend the course to any newcomers into our department. We are now able to go out and solve any issues with confidence.”

T. Kennett (Royal Air Force, United Kingdom)

77

©2010. All rights reserved. The Emerson is a trademark and service mark of Emerson Electric Co. All other marks are the property of their

respective owners.

The contents of this publication are presented for informational purposes only and, while every effort has been made to ensure their accuracy,

they are not to be construed as warranties or guarantees, expressed or implied, regarding the products or services described herein or their use or

applicability. We reserve the right to modify or improve the designs or specifications of our products at any time without notice.

Printed in Germany. MC-001289

05/10

European Instrumentation Training Centres - Contact Details-

Flow Training Centre

Neonstraat 1 6718 WX Ede The Netherlands Tel. +31 (0)318 495431 ITO-Europe@emerson.com

Argelsrieder Feld 3 82234 Wessling Germany Tel. +49 (0)8153 939133 ITO-Europe@emerson.com

About Emerson

Emerson has been in business since 1890 and is a global leader in bringing technology and engineering together to create innovative solutions for our customers. Based on a disciplined management process, deep customer relationships and vast experience in a wide range of industries and markets, Emerson is able to see tomorrow’s business challenges. Rosemount and Micro Motion, divisions of Emerson Process Management, offer a wide range of products and services in the areas of flow, pressure, temperature, level, wireless, density and viscosity measurements.

For a complete list of Emerson Process Management web sites, please visit www.EmersonProcess.com

Measurement Training Centre

Level Training Centre

Gamlestadsvagen 18B Goteborg 402 51 Sweden Tel. +46 (0)31 3370713 ITO-Europe@emerson.com