2
Copyright © Petroleum Technology Company 2016 CAPEX Savings and Integrity Enhancement in Gas Lift Wells Surface Pipework All rights reserved Petroleum Technology Company (hereinafter PTC) 2016. Reproduction, distribution or storage of any kind without the written consent from PTC is prohibited. Abstract Until recently, it has been necessary to have two separate pipe-lines connected to the A Annulus wellhead in gas lifted wells. One line for lift gas injection, and one for blow down. This white paper describes the use of field proven technologies, which can significantly reduce the amount of pipework and number of valves necessary in the wellbay area. In addition to space-saving, the benefits include: CAPEX savings, improved well integrity, and more reliable pressure and temperature data acquisition. Traditional Gas Lift Wellhead Pipework Arrangement The typical ’two line’ arrangement is shown below on the LHS. This was necessary because a check valve type device is usually installed on the lift gas injection line, which would not permit blow down. Simplified Gas Lift Wellhead Pipework arrangement This simplified arrangement is shown on the RHS above. The enabling technologies are the: MSAS-G: a double integrity barrier, hydraulically actuated wellhead safety valve system (with bi directional flow / fail safe closed functionality similar to a sub- surface safety valve). VR Sense: a double integrity barrier pressure / temperature sensor. They are installed in the threaded profiles (VR profiles), which are present in all wellheads (machined into both side outlets). Because the MSAS-G enables bi directional flow, there is no longer any need for separate injection and blow down lines to the wellhead. The spare port on the wellhead can therefore be used to install a double barrier annulus Pressure /Temperature sensor, which significantly improves well integrity. Improved data reliability is also facilitated [1]. www.ptc.as 1 Traditional vs Simplified GL Wellhead Pipeline / valve arrangements P P P P Remove 4 x A Annulus Gate Valves 1 x B Annulus Gate Valves 1 x Check Valve 3 x Instrument flanges and gauges Associated Pipework Replace with 2 VR Sensors / 1x MSAS G P Bleed / blow down to flare / drains Bleed / blow down to flare / drains Lift Gas Injection Lift Gas Injection Primary Barrier Secondary Barrier MSAS-G VR Sense

Traditional vs Simplified GL Wellhead Pipeline / valve ... sa… · Traditional Gas Lift Wellhead Pipework Arrangement The typical ’two line’ arrangement is shown below on the

  • Upload
    others

  • View
    17

  • Download
    1

Embed Size (px)

Citation preview

Page 1: Traditional vs Simplified GL Wellhead Pipeline / valve ... sa… · Traditional Gas Lift Wellhead Pipework Arrangement The typical ’two line’ arrangement is shown below on the

Copyright©PetroleumTechnologyCompany2016

CAPEXSavingsandIntegrityEnhancementinGasLiftWellsSurfacePipeworkAllrightsreservedPetroleumTechnologyCompany(hereinafterPTC)2016.Reproduction,distributionorstorageofanykindwithoutthewrittenconsentfromPTCisprohibited.AbstractUntilrecently,ithasbeennecessarytohavetwoseparatepipe-linesconnectedtotheAAnnuluswellheadingasliftedwells. One line for lift gas injection, and one for blow down. This white paper describes the use of field proventechnologies,which can significantly reduce theamountofpipeworkandnumberof valvesnecessary in thewellbayarea. In addition to space-saving, the benefits include: CAPEX savings, improved well integrity, and more reliablepressureandtemperaturedataacquisition.TraditionalGasLiftWellheadPipeworkArrangementThetypical’twoline’arrangementisshownbelowontheLHS.Thiswasnecessarybecauseacheckvalvetypedeviceisusuallyinstalledontheliftgasinjectionline,whichwouldnotpermitblowdown.

SimplifiedGasLiftWellheadPipeworkarrangementThissimplifiedarrangementisshownontheRHSabove.Theenablingtechnologiesarethe:

• MSAS-G: a double integrity barrier, hydraulically actuated wellhead safetyvalve system (withbidirectional flow / fail safe closed functionality similar toa sub-surfacesafetyvalve).• VRSense:adoubleintegritybarrierpressure/temperaturesensor.They are installed in the threaded profiles (VR profiles), which are present in allwellheads (machined into both side outlets). Because the MSAS-G enables bidirectional flow, there is no longer any need for separate injection and blow downlinestothewellhead.ThespareportonthewellheadcanthereforebeusedtoinstalladoublebarrierannulusPressure/Temperaturesensor,whichsignificantly improveswellintegrity.Improveddatareliabilityisalsofacilitated[1].

www.ptc.as 1

Traditional vs Simplified GL Wellhead Pipeline / valve arrangements

P P

P P

Remove •  4 x A Annulus Gate Valves •  1 x B Annulus Gate Valves •  1 x Check Valve •  3 x Instrument flanges and gauges •  Associated Pipework Replace with •  2 VR Sensors / 1x MSAS G

P

Bleed / blow down to flare / drains

Bleed / blow down to flare / drains

Lift Gas Injection

Lift Gas Injection

Primary Barrier Secondary Barrier

MSAS-G

VRSense

Page 2: Traditional vs Simplified GL Wellhead Pipeline / valve ... sa… · Traditional Gas Lift Wellhead Pipework Arrangement The typical ’two line’ arrangement is shown below on the

Copyright©PetroleumTechnologyCompany2016

CAPEXandOPEXSavingsTheuseoftheMSAS-GandVRSenseeliminatestheneedfor:

• 4xAAnnulusGateValves• 1xBAnnulusGateValve• 1xCheckValve• 3InstrumentFlangesandPressureGauges• AssociatedPipework

This can amount to significantCAPEX savings, especiallywhereCRAmaterials are employedandwhere lengthypiperunstoandfromthevariousmanifoldarerequired.ThelifecycleOPEXcostsforNDT/maintainingthevariousvalves/pipeworkthatcanberemovedareobviouslyalsoeliminated.InapublishedSPEpaper[2]oneOperatingCompanyconcluded:

“In addition to the safety benefits of less facilities subjected to damage from drilling and maintenanceoperations,thereisadirectcostsavingsachievedthroughtheoptimizationofsurfacefacilities.…farexceededthecostofimplementingthenewLiftGasSafetySystem(LGSS)technologyintothefielddevelopment”

WellIntegrityBenefitsAnumberofwell integritybenefitsarealsodelivered.ThewidelyfollowedTheNorsokD10‘Well IntegrityforDrillingandWellOperationsGuidelines’states:

“AlargevolumeofpressurisedhydrocarbongasintheAAnnulirepresentsasubstantialrisk”……"AllgasliftedwellsshallhavetwobarrierstopreventreleaseoftheAannulusgasvolume”

Referringagain to thewelldiagramsoverleaf, it canbeseen thenewapproach facilitates this requirement. It isalsonoteworthythattheprimarybarrierenvelopenowsitswithinthewellbore,whereitisprotectedfromdroppedobjectorcollisiondamage.This is in contrast to the traditional configuration, where only a single barrier exists, some distance away from thewellbore.Thisisparticularlyimportantinsituationswheremultiplewellsareco-locatedinaconfinedplatformorwellpad.Inthesecasesunplannedincidentsduringoperationsonadjacentwells,couldresultindamageto‘singlebarrier’pipeworkcontaininghighpressureliftgas,wherenosecondarymeansofisolationispossible.

Although not the cause of the disaster, thesituation resulted in 4 wells continuing to blowout,viathetubing/casingannulus(AAnnulus),for5 weeks after the original fire was extinguished[3].The reason the fires continued to burn was acombinationof:• The single barrier that the annulus linegate valve offered vs the release of annulus gasfailed, allowing communication between theannuluscontentsandatmosphere.• Thecheckvalvesinthedownholegasliftvalves failed, allowing reservoir fluids to followcontinuouslyintotheannulus.It was after this disaster that the need for adouble barrier to flow from the gas lift annuluswasfirstrecognised.

[1]PTCWhitePaper:AnewApproachtoAnnulusPressureMonitoring:ImprovingDataReliabilityandWellIntegrity,whileReducingLifecycleCosts[2]SPEPaper171748:SurfaceSafetySystemEnhancesGasLiftSafetyandOptimizesSurfaceLineArchitectureonIslandWells[3]FireintheNight,ThePiperAlphaDisaster:SMcGinty