Embed Size (px)
Citation preview
TPR-L Peel RivetFastening Solution for Problematic Roof Decks
Product DescriptionDekfast™ T.P.R. Peel Rivet is a two-piece, aluminum magnesium alloy fastener specially designed for attaching insulation and membrane to decks where threaded fasteners can not achieve required pull-out values. During the setting process, the rivet produces four load bearing curls against the underside of the deck.
The result: A structural fastener to resist dynamic wind uplift loads.
Features and Benefitsn High pull-out valuesn Cannot be over-tightenedn Consistent structural performancen One fastener can accommodate a wide range of material thicknessesn Safe and successful installation every timen Constructed from a highly corrosion resistant aluminum-magnesium alloy
Technical Data
NotesDimensions are nominal inches unless noted. Ultimate values listed are the result of laboratory testing. Pull-out (pounds ultimate) strength values may vary from tabulated loads depending upon the uniqueness of the application. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Selection Minimum Maximum Carton
Length Clamping Length Clamping Length Material No. North American Code Qty. 1-1/2" 1/2" 1/2" 1241233 TPR-L-6,3x38 Peel Rivet 1,000 2" 1/2" 1" 1326232 TPR-L-6,3x 51 Peel Rivet 1,000 3" 7/8" 2" 1241241 TPR-L-6,3x 76 Peel Rivet 500 4" 1-5/8" 3" 1241244 TPR-L-6,3x102 Peel Rivet 500 5" 2-5/8" 4" 1241246 TPR-L-6,3x127 Peel Rivet 500 6" 3-5/8" 5" 1241248 TPR-L-6,3x152 Peel Rivet 500 7" 4-5/8" 6" 1241249 TPR-L-6,3x178 Peel Rivet 250 8" 5-5/8" 7" 1241250 TPR-L-6,3x203 Peel Rivet 250 9" 6-5/8" 8" 1241251 TPR-L-6,3x229 Peel Rivet 250 10" 7-5/8" 9" 1241252 TPR-L-6,3x254 Peel Rivet 250
Installation
Head: Low Profile Mushroom Head Dia: .480" Shank Dia: .225" Installed Dia: 1.65"
Pull-out (lbs avg.): 28 ga (Loadmaster): 385 26 ga (Standing Seam): 465 1/2" OSB: 330 3" Poured Gypsum: 430
SFS intec Division Construction 1045 Spring Street PO Box 6326US-Wyomissing, PA 19610
800 234 4533T +1 610 376 5751F +1 610 376 [email protected]
SFS intec - Canada40 Innovation DriveDundas, ON L9H 7P3T +1 905 689 [email protected]
Technical advice and sales service
TAURUS 2 Peel RivetPneumatic-hydraulic setting tool for the installation of TPR-L Peel RivetsMaterial No.: 1457802
Use with 2" or 3" round Galvalume stress plates or 2-7/8" hex Galvalume stress plates.Pre-drill diameter for all substrates is 7mm (9/32"). The specially designed pulling tool is required for all installations and is available in pneumatic and electric models. Minimum of 1" penetration required in steel, woodfiber, wood, and lightweight concrete.
Drill Insert Set
© 2
016
SFS
inte
cTe
chni
cal c
hang
es r
eser
ved.
