GRUNDFOS DATA BOOKLET

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

In-line circulator pumps50 Hz

Lenntech

TP Series 300 pumps

28

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

7. TP Series 300 pumps

Fig. 12 TP Series 300

Technical data

* At 120 to 150 °C, the maximum operating pressure is less than 23 bar.

ConstructionGrundfos TP, TPD Series 300 pumps are single-stage, close-coupled pumps with in-line inlet and outlet ports of identical diameter. The pumps are fitted with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid sleeve coupling.Most TP Series 300 pumps are available as single-head, TP, and twin-head, TPD pumps.TP Series 300 pumps have PN 16 flanges or PN 25 flanges. The largest pumps have DN 500, PN 40 inlet flanges and DN 400, PN 40 outlet flanges and a maximum operating pressure of 25 bar.The pumps are fitted with an unbalanced or a balanced mechanical shaft seal.The pumps are of the top-pull-out design, that is you can remove the power head (motor, pump head and/or motor stool and impeller) for maintenance or service while the pump housing remains in the pipes. The pump housing is provided with a replaceable wear ring to ensure high pump efficiency for life.The twin-head pumps are designed with two parallel power heads. A non-return flap valve in the common outlet port is opened by the flow of the pumped liquid and prevents backflow of liquid into the idle pump head.As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing.The impeller is hydraulically balanced to minimise axial forces.TP, TPD Series 300 pumps are fitted with high-efficiency motors.TP Series 300 pumps with bronze impeller are suitable for pumping brine.

Gr8

259

PN 16 version PN 25 version

Flow rate [m3/h] Up to 2000 Up to 4500

Head [m] Up to 93 Up to 140

Liquid temperature [°C] -25 to +140 -40 to +150*

Maximum operating pressure [bar] 16 25

Direction of rotation Clockwise

TP S

erie

s 30

0 pu

mps

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Materials

Fig. 13 Sectional drawing of TP Series 300

Material specification

TP Series 300, PN 16

TP Series 300, PN 25

TP Series 300, DN 400, PN 25

Mechanical shaft sealFor 16-bar versions, these types of unbalanced mechanical shaft seals are available as standard:• BAQE

The BAQE shaft seal is a rubber bellows seal with carbon/silicon carbide seal faces and secondary seals of EPDM.

• BQQEThe BQQE shaft seal is a rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM.

For 25-bar versions, these types of balanced mechanical shaft seals are available as standard:• DAQF

The DAQF shaft seal is a balanced O-ring seal with carbon/silicon carbide seal faces and secondary seals of FXM.

• DQQEThe DQQE shaft seal is a balanced O-ring seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM.

• DBUEThe DBUE shaft seal is a balanced O-ring seal with carbon/tungsten carbide seal faces and secondary seals of EPDM.

For further information about common pumped liquids with recommended shaft seals, .Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles. .

ConnectionsTP Series 300 pumps have PN 16 or PN 25 flanges. All dimensions are according to ISO 7005-2 or EN 1092-2.

TM04

958

6 21

15

Pos. Component Material EN/DIN

1 Pump housing Cast iron EN-GJL-250 EN-JL 1040

2 Impeller Cast iron EN-GJL-200, bronze CuSn10EN-JL 10302.1093

3 Stub shaftTwo-part stub shaftStainless steelStainless steel/steel

1.43011.4301/1.0301

4 Pump head/motor stool Cast iron EN-GJL-250 EN-JL 1040

Secondary seals EPDM

Rotating seal faceMetal-impregnated carbonSilicon carbide

Stationary seat Silicon carbide

5 Wear ring Bronze CuSn10/brass CuZn34Mn3Al2Fe1-C 2.1093

Pos. Component Material EN/DIN

1 Pump housing Ductile cast iron EN-GJS-400-18-LT EN-JS 1025

2 Impeller Cast iron EN-GJL-200, bronze CuSn10EN-JL 10302.1093

3 Stub shaftTwo-part stub shaftStainless steelStainless steel/steel

1.43011.4301/1.0301

4 Motor stool Cast iron EN-GJL-250 EN-JL 1040

Secondary seals EPDMFXM

Rotating seal faceMetal-impregnated carbonSilicon carbide

Stationary seat Silicon carbide

5 Wear ring Bronze CuSn10/brass CuZn34Mn3Al2Fe1-C 2.1093

1

2

3

4

5

Pos. Component Material EN/DIN

1 Pump housing Ductile cast iron EN-GJS-400-18 (A-LT) EN-JS1020

2 ImpellerDuctile cast iron EN-GJS-400 EN-JS1030Bronze CuSn10 2.1093

3 Pump shaft Stainless steel 1.44364 Coupling Cast iron EN-GJL-250 EN-JL10405 Motor stool Cast iron EN-GJL-250 EN-JL1040

Secondary seals EPDM rubberRotating seal face Resin-impregnated carbonStationary seat Tungsten carbide

TP Series 300 pumps

30

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Features and benefitsTP Series 300 pumps have these features and benefits:

Optimised hydraulics for high efficiency– Reduced power consumption.

High-efficiency motors– TP pumps are fitted with high-efficiency motors.

High-efficiency motors offer reduced energy consumption. TP pumps are primarily fitted with motors that meet the legislative requirements of the EuP IE3 grade. TP pumps are also available with motors from 2.2 to 132 kW that meet the legislative requirements of the EuP IE4 grade. For further information, .

Top-pull-out design– Easy dismantling in case of service.

In-line design– Contrary to end-suction pumps, in-line pumps

allow straight pipes and thus often reduced installation costs.

Motor-pump shaft with sleeve coupling– Stable and quiet operation.– Easy dismantling in case of service.

Hydraulically and mechanically balanced impeller– The impeller is hydraulically and mechanically

balanced to increase the life of motor bearings and shaft seal.

Surface treatmentTP Series 300 pumps are given the following surface treatment:

Electrocoating includes:1. Alkaline cleaning.2. Pretreatment with zinc phosphate coating.3. Cathodic electrocoating, epoxy.4. Curing of paint film at 200-250 °C.For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request.

Pump type Electrocoating Spray paintingTP Series 300 from DN 32 to DN 350 x

TP Series 300, DN 400 2x

Perf

orm

ance

ran

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 2-pole, PN 6, 10, 16

TM02

755

0 46

17

11.

52

34

56

81010

1520

3040

5060

8010

010

015

020

030

040

0

Q [m

³/h]

2345681015203040506080[m]

H

112

34

56

78

91010

2030

4050

6070

Q [l

/s]

2030405060708090100

100

200

300

400

500

600

700

800

[kP

a]p

TP

(D),

TP

E(D

)P

N 6

/10/

16, 2

-pol

e, 5

0 H

z

32-8

0

32-5

0

25-9

0

25-5

0

25-8

0

125-

310

125-

360

65-

170

65-2

10

65-2

5050-4

20

50-5

40

50-6

30

40-4

3040

-530

40-6

30

100-

25010

0-31

010

0-36

0

100-

390

65-3

40

65-4

10

65-4

60

65-5

5065-

660

65-7

20

65-9

30

50-1

60

50-1

90

50-2

40

50-2

9050

-360

50-4

30

50-7

10

50-8

30

50-9

00

40-2

40

40-3

0040-3

60

32-2

00

32-2

50

32-3

20

32-3

80

32-4

60

32-5

80

100-

120

80-1

20

65-1

80

65-1

20

65-6

0

50-1

80

50-1

20

50-6

0

40-2

70

40-2

30

40-1

90

40-1

80

40-1

20 40-6

0

32-2

30

32-1

80

32-1

50

32-1

20 32-6

0

40-5

0

40-9

0

80-1

40

80-1

8080-2

10

80-2

40

80-2

5080

-3308

0-40

0

80-5

20

80-5

70

80-7

00

100-

16010

0-20

0

100-

240

100-

480

32-9

0

12

Performance range

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 2-pole, PN 25

TM06

653

3 42

17

2030

4050

6070

8010

015

020

030

040

050

0

Q [m

³/h]

30405060708090100

120

140

[m]

H

67

89

101020

3040

5060

7080

9010

010

0Q

[l/s

]

300

400

500

600

700

800

900

1000

1000

[kP

a]p

TP

PN

25,

2-p

ole,

50

Hz

100-

530

100-

650

100-

800

100-

950

100-

1040

100-

1200

100-

1410

Perf

orm

ance

ran

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 4-pole, PN 6, 10, 16

TM02

755

1 42

17

23

45

68

1012

1520

3040

5060

8010

015

020

030

040

060

010

0015

0020

00

Q [m

³/h]

12345681010152030405060[m]

H

112

34

56

78

101020

3040

5060

8010

010

020

030

0Q

[l/s

]

101020304050607080100

100

200

300

400

500

600

700

[kP

a]p

TP

(D),

TP

E(D

)P

N 6

/10/

16, 4

-pol

e, 5

0 H

z

350-

280

350-3

20

350-

360

350-

420

350-

480

350-

530

350-

650

350-

780

300-

190

300-

220

300-2

5030

0-290

300-

390

300-

420

300-

430

300-

500

300-

550

150-

150-

155

150-

110

150-

70

125-

95

125-8

0

125-

125-

400

125-

340

125-

300

125-

230

125-

190

50-1

40

50-1

2050

-80

40-1

40

40-1

10

200-

160

200-

190

200-

200

200-

240

200-

290

200-

50

200-

70200

-9020

0-13

0

200-

150

150-

450

150-

520

150-

660

100-

70

100-

90

100-

110

200-

660

200-

530

200-

590

150-

260

150-

280

150-

340

150-

390

100-

410

100-

370

100-

330

100-

250

100-

200

100-

170

100-

130

80-3

40

80-2

70

80-2

40

80-1

70 80-

150

80-1

10

80-9

0

80-7

0

65-1

10

65-1

30

65-1

50

65-1

70

65-2

40

65-9

0

50-1

90

50-2

30

50-9

0

40-1

00

32-1

00

32-1

20

32-8

0

100-

60

100-

30

80-6

0

80-3

0

65-6

0

65-3

0

50-6

0

50-3

0

40-9

040

-60 40

-30

32-6

0

32-4

0

32-3

0

125-

130

125-

160

150-

130

150-

160

150-

220

150-

200

150-

250

200-

410

200-

320

200-

270

200-

470

200-

400

200-

360

200-3

30

60

170

210

0010

00160 1060

Performance range

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 4-pole, PN 25

TM02

686

9 42

17

2030

4050

6080

100

150

200

300

400

500

600

800

1000

1500

2000

3000

5000

Q [m

³/h]

8101520304050607080[m]

H

67

89

101020

3040

5060

7080

100

100

200

300

400

500

600

800

Q [l

/s]

8090100

100

200

300

400

500

600

700

800

[kP

a]p

TP

PN

25,

4-p

ole,

50

Hz

200-

410

200-

320

200-

660

200-

590

200-

530

200-

470

200-

400

200-

360

200-

270

200-

290

200-

240

200-

200

200-

160

150-

660

150-

520

150-

450

150-

390

150-

280

150-

260

150-

250

150-

220

150-

150-

160

150-

130

125-

400

125-

340

125-

300

125-

230

125-

190

125-

150

100-

140

100-

200

100-

250

100-

330

100-

370

100-

410

350-

280

350-3

20

350-

360

350-

420

350-

480

350-

530

350-

650

350-

780

300-

190

300-

220

300-

250

300-

290

300-

390

300-4

20

300-

430

300-

500

300-

550

400-

720

400-

760

400-

670

400-

540

400-

510

400-

470

200

Perf

orm

ance

ran

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 6-pole, PN 16

Note: All QH curves apply to single-head pumps. For further information about curve conditions, see page 138.

TM02

876

8 38

14

����

���

����

���

���

���

���

��

����

��������������

�

��

��

������

���

��

������

����������������

���

���

�����

�����

�!���"��� #�$"�����%

�������

�������

�������

������

���������

��������

��������

��������

��������

��������

V7124417 1117ECM: 1222592 Th

e na

me

Gru

ndfo

s, th

e G

rund

fos

logo

, and

be

thin

k in

nova

te a

re re

gist

ered

trad

emar

ks o

wne

d by

Gru

ndfo

s H

oldi

ng A

/S o

r Gru

ndfo

s A

/S, D

enm

ark.

All

right

s re

serv

ed w

orld

wid

e.©

Cop

yrig

ht G

rund

fos

Hol

ding

A/S

Lenntechinfo@lenntech.com Tel. +31-152-610-900www.lenntech.com Fax. +31-152-616-289info@lenntech.com Tel. +31-152-610-900www.lenntech.com Fax. +31-152-616-289

Lenntech

2. Performance rangePerformance range, TPE2, TPE3, PN 6, 10, 16Performance range, TPE2 D, TPE3 D, twin-head operation, PN 6, 10, 16Performance range, 2-pole, PN 6, 10, 16Performance range, 2-pole, PN 25Performance range, 4-pole, PN 6, 10, 16Performance range, 4-pole, PN 25Performance range, 6-pole, PN 16

3. Product rangeProduct range, TPE2, TPE2 D, TPE3, TPE3 DProduct range, 2-pole, PN 6, 10, 16, 25Product range, 4-pole, PN 6, 10, 16, 25Product range, 6-pole, PN 16

4. Operating conditionsSystem and test pressuresSound pressure levelAmbient temperatureInstallation altitude

5. Pumped liquidsPumped liquidsLiquid temperatureList of pumped liquidsRecommended shaft seal for water- glycol mixture

6. TP Series 100 and 200 pumpsTechnical dataConstructionMaterialsMechanical shaft sealConnectionsFeatures and benefits

7. TP Series 300 pumpsTechnical dataConstructionMaterialsMechanical shaft sealConnectionsFeatures and benefits

8. TPE Series 1000 pumpsTechnical dataConstructionApplicationsTPE, TPED pumps with extended performance rangeOperating modes of twin-head pumpsControl options

9. TPE Series 2000 pumpsTechnical dataConstructionApplicationsTPE, TPED pumps with extended performance rangeOperating modes of twin-head pumpsControl options

10. TPE2Technical dataConstructionMaterialsApplicationsMultipump systemControl options

11. TPE3Technical dataConstructionMaterialsApplicationsMultipump systemControl options

12. Overview of functions13. User interfaces for TPE pumpsControl panel for TPE2 and TPE Series 1000 pumps, 0.12 - 11 kW, 2- pole and 0.12 - 7.5 kW, 4-poleSetpoint setting

Control panel for TPE Series 1000 pumps, 15-22 kW, 2-pole and 11 - 18.5 kW, 4-poleSetpoint settingSetting to maximum curve dutySetting to minimum curve dutyStart-stop of pump

Control panel for TPE Series 2000 pumps, 15-22 kW, 2-pole and 11 - 18.5 kW, 4-poleAdvanced control panel for TPE3 and TPE Series 2000 pumps, 0.12 - 11 kW, 2-pole and 0.12 - 7.5 kW, 4- pole"Home" displayMenu overview for advanced control panel

Grundfos GOCommunicationMenu overview for Grundfos GO

Description of selected functions"Heat energy monitor""Setpoint""Operating mode""Set manual speed""Set user-defined speed""Control mode""Proportional-pressure setup""FLOWLIMIT""Automatic night setback""Sensor type""Analog inputs""Built-in Grundfos sensor""Pt100/1000 inputs""Digital inputs""Digital inputs/outputs""Signal relays 1 and 2" ("Relay outputs")"Analog output""Controller" ("Controller settings")"Operating range""External setpoint influence""Predefined setpoints""Temperature influence""Limit-exceeded function"Special functions"Service"CommunicationGeneral settings"Assist"

Priority of settingsGrundfos EyeIndicator lights and signal relays

14. Factory settings of E-pumps15. CommunicationCommunication with TPE2, TPE2 D, TPE3, TPE3 D, TPE, TPED pumps

16. Speed regulation of TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D pumpsAffinity equations

17. Control of pumps in parallelAlternation/standby functionPumps connected to Control MPCPumps connected to Control MPC Series 2000

18. Grundfos CUETP pumps connected to Grundfos CUE, external frequency convertersFunctionsExternal communication

19. Motor dataMotorsElectrical data, mains-operated motorsElectrical data, speed-controlled motors

20. InstallationMechanical installationElectrical installationMains-operated motors

21. MGE motorsMotors for TPE, TPE2 and TPE3 pumps fitted with 2-pole motors from 0.12 - 11 kW and 4-pole motors from 0.12 - 7.5 kWSingle-phase supply voltageThree-phase supply voltageInputs and outputsEMC, electromagnetic compatibilityEnclosure classInsulation classAmbient temperatureStandby power consumptionCable entriesSound pressure levelMotor protectionAdditional protectionMaximum number of starts and stopsWiring diagramsConnection terminals

MGE motors, 11 to 18.5 kW, 4-pole, and 15 to 22 kW, 2-poleSupply voltageInput and outputEMC, electromagnetic compatibility to EN 61800-3Enclosure classInsulation classAmbient temperatureRelative humiditySound pressure levelMotor protectionAdditional protectionMaximum number of starts and stopsWiring diagram, 11-22 kWOther connections

Identification of functional module

22. Electromagnetic compatibility, EMCElectromagnetic compatibility and proper installationGeneral informationWhat is electromagnetic compatibility?EmissionImmunityE-pumps and electromagnetic compatibilityWhere to install E-pumps?What is meant by the first and the second environment?Electromagnetic compatibility and proper installationConnection of mains supply in MGE

23. Flanges for TP pumpsFlange dimensions

24. Curve chartsHow to read the curve chartsCurve conditions

25. Performance curves and technical dataTPE2, TPE2 D, TPE3, TPE3 D, PN 6, 10, 16TP, TPD, TPE, TPED, 2-pole, PN 6, 10, 16, 25TP, TPD, TPE, TPED, 4-pole, PN 6, 10, 16, 25TP, TPD, TPE, TPED, 6-pole, PN 16

26. Weights and shipping volumeTPE2, TPE2 D, TPE3, TPE3 D, PN 6, 10, 16TP, TPD, TPE, TPED, 2-pole, PN 6, 10, 16, 25TP, TPD, TPE, TPED, 4-pole, PN 6, 10, 16, 25TP, TPD, 6-pole, PN 6, 10, 16

27. Minimum efficiency indexTPE2, TPE2 D, TPE3, TPE3 DTP, TPD, TPE, TPED, 2-pole, PN 6, 10, 16TP, TPD, TPE, TPED, 4-pole, PN 6, 10, 16TP, TPD, 6-pole, PN 16TP, PN 25

28. AccessoriesUnions and valves, TP Series 100CounterflangesAdapter flanges for various port-to-port lengths

Base platesBlanking flangesInsulating kitsKits for TPE2, TPE3 pumps

SensorsFlow sensorsTemperature sensorsPressure sensors

External Grundfos sensorsMP 204, advanced motor protectionControl MP 204PotentiometerGrundfos GOCIU communication interface unitsCIM communication interface modulesEMC filter

29. Minimum inlet pressure - NPSHTPE2, TPE2 D, TPE3, TPE3 DTP, TPE, TPD, TPED, 2-pole, PN 6, 10, 16, 25TP, TPE, TPD, TPED, 4-pole, PN 6, 10, 16, 25TP, TPD, 6-pole, PN 16

30. Key application dataOperating conditions

31. Grundfos Product CenterBookmarks from TP-Performance.pdf2. Performance rangePerformance range, TPE2, TPE3, PN 6, 10, 16Performance range, TPE2 D, TPE3 D, twin-head operation, PN 6, 10, 16Performance range, 2-pole, PN 6, 10, 16Performance range, 2-pole, PN 25Performance range, 4-pole, PN 6, 10, 16Performance range, 4-pole, PN 25Performance range, 6-pole, PN 16

3. Product rangeProduct range, TPE2, TPE2 D, TPE3, TPE3 DProduct range, 2-pole, PN 6, 10, 16, 25Product range, 4-pole, PN 6, 10, 16, 25Product range, 6-pole, PN 16

4. Operating conditionsSystem and test pressuresSound pressure levelAmbient temperatureInstallation altitude

5. Pumped liquidsPumped liquidsLiquid temperatureList of pumped liquidsRecommended shaft seal for water- glycol mixture

6. TP Series 100 and 200 pumpsTechnical dataConstructionMaterialsMechanical shaft sealConnectionsFeatures and benefits

7. TP Series 300 pumpsTechnical dataConstructionMaterialsMechanical shaft sealConnectionsFeatures and benefits

8. TPE Series 1000 pumpsTechnical dataConstructionApplicationsTPE, TPED pumps with extended performance rangeOperating modes of twin-head pumpsControl options

9. TPE Series 2000 pumpsTechnical dataConstructionApplicationsTPE, TPED pumps with extended performance rangeOperating modes of twin-head pumpsControl options

10. TPE2Technical dataConstructionMaterialsApplicationsMultipump systemControl options

11. TPE3Technical dataConstructionMaterialsApplicationsMultipump systemControl options

12. Overview of functions13. User interfaces for TPE pumpsControl panel for TPE2 and TPE Series 1000 pumps, 0.12 - 11 kW, 2- pole and 0.12 - 7.5 kW, 4-poleSetpoint setting

Control panel for TPE Series 1000 pumps, 15-22 kW, 2-pole and 11 - 18.5 kW, 4-poleSetpoint settingSetting to maximum curve dutySetting to minimum curve dutyStart-stop of pump

Control panel for TPE Series 2000 pumps, 15-22 kW, 2-pole and 11 - 18.5 kW, 4-poleAdvanced control panel for TPE3 and TPE Series 2000 pumps, 0.12 - 11 kW, 2-pole and 0.12 - 7.5 kW, 4- pole"Home" displayMenu overview for advanced control panel

Grundfos GOCommunicationMenu overview for Grundfos GO

Description of selected functions"Heat energy monitor""Setpoint""Operating mode""Set manual speed""Set user-defined speed""Control mode""Proportional-pressure setup""FLOWLIMIT""Automatic night setback""Sensor type""Analog inputs""Built-in Grundfos sensor""Pt100/1000 inputs""Digital inputs""Digital inputs/outputs""Signal relays 1 and 2" ("Relay outputs")"Analog output""Controller" ("Controller settings")"Operating range""External setpoint influence""Predefined setpoints""Temperature influence""Limit-exceeded function"Special functions"Service"CommunicationGeneral settings"Assist"

Priority of settingsGrundfos EyeIndicator lights and signal relays

14. Factory settings of E-pumps15. CommunicationCommunication with TPE2, TPE2 D, TPE3, TPE3 D, TPE, TPED pumps

16. Speed regulation of TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D pumpsAffinity equations

17. Control of pumps in parallelAlternation/standby functionPumps connected to Control MPCPumps connected to Control MPC Series 2000

18. Grundfos CUETP pumps connected to Grundfos CUE, external frequency convertersFunctionsExternal communication

19. Motor dataMotorsElectrical data, mains-operated motorsElectrical data, speed-controlled motors

20. InstallationMechanical installationElectrical installationMains-operated motors

21. MGE motorsMotors for TPE, TPE2 and TPE3 pumps fitted with 2-pole motors from 0.12 - 11 kW and 4-pole motors from 0.12 - 7.5 kWSingle-phase supply voltageThree-phase supply voltageInputs and outputsEMC, electromagnetic compatibilityEnclosure classInsulation classAmbient temperatureStandby power consumptionCable entriesSound pressure levelMotor protectionAdditional protectionMaximum number of starts and stopsWiring diagramsConnection terminals

MGE motors, 11 to 18.5 kW, 4-pole, and 15 to 22 kW, 2-poleSupply voltageInput and outputEMC, electromagnetic compatibility to EN 61800-3Enclosure classInsulation classAmbient temperatureRelative humiditySound pressure levelMotor protectionAdditional protectionMaximum number of starts and stopsWiring diagram, 11-22 kWOther connections

Identification of functional module

22. Electromagnetic compatibility, EMCElectromagnetic compatibility and proper installationGeneral informationWhat is electromagnetic compatibility?EmissionImmunityE-pumps and electromagnetic compatibilityWhere to install E-pumps?What is meant by the first and the second environment?Electromagnetic compatibility and proper installationConnection of mains supply in MGE

23. Flanges for TP pumpsFlange dimensions

24. Curve chartsHow to read the curve chartsCurve conditions

25. Performance curves and technical dataTPE2, TPE2 D, TPE3, TPE3 D, PN 6, 10, 16TP, TPD, TPE, TPED, 2-pole, PN 6, 10, 16, 25TP, TPD, TPE, TPED, 4-pole, PN 6, 10, 16, 25TP, TPD, TPE, TPED, 6-pole, PN 16

26. Weights and shipping volumeTPE2, TPE2 D, TPE3, TPE3 D, PN 6, 10, 16TP, TPD, TPE, TPED, 2-pole, PN 6, 10, 16, 25TP, TPD, TPE, TPED, 4-pole, PN 6, 10, 16, 25TP, TPD, 6-pole, PN 6, 10, 16

27. Minimum efficiency indexTPE2, TPE2 D, TPE3, TPE3 DTP, TPD, TPE, TPED, 2-pole, PN 6, 10, 16TP, TPD, TPE, TPED, 4-pole, PN 6, 10, 16TP, TPD, 6-pole, PN 16TP, PN 25

28. AccessoriesUnions and valves, TP Series 100CounterflangesAdapter flanges for various port-to-port lengths

Base platesBlanking flangesInsulating kitsKits for TPE2, TPE3 pumps

SensorsFlow sensorsTemperature sensorsPressure sensors

External Grundfos sensorsMP 204, advanced motor protectionControl MP 204PotentiometerGrundfos GOCIU communication interface unitsCIM communication interface modulesEMC filter

29. Minimum inlet pressure - NPSHTPE2, TPE2 D, TPE3, TPE3 DTP, TPE, TPD, TPED, 2-pole, PN 6, 10, 16, 25TP, TPE, TPD, TPED, 4-pole, PN 6, 10, 16, 25TP, TPD, 6-pole, PN 16

30. Key application dataOperating conditions

31. Grundfos Product Center