Upload
others
View
1
Download
1
Embed Size (px)
Citation preview
Toys testing equipment
TW-200 ASTM Impact Media
Simulate the real floor, to test the toys fall on the floor of the toys produced after the
destruction and damage caused by the impact of whether the product meet the
requirements dropped
Specification:1/8″×12″×12″ 9 a
Standards :ASTM F963 8.7.1
TW-200 EN-71 Impact Media
Simulate the real floor, to test the toys fall on the floor of the toys
produced after the destruction and damage caused by the impact of
whether the product meet the requirements dropped
Specification:2mm Rubber+4mm SST Sheet 600mm×600mm
Standards: EN71-1998 8.5
TW-201Impact Tester
Purpose : Reduce the material damage or the danger of imitation toys protection
devices as the real face.
Range: imitation protect device ( clear material protector, headpiece, cap, blinker)
Standards: EN 71-1998 8.7
specifications:
1.dimension :300(l)x300(w)x16(h)mm
2.adjust height:0-200mm
3.impact hammer diameter:80.00mm
4.impact hammer weight :1Kg
5. with metric / imperial unit height dictate ruler
TW-203Rattle Test Fixture
Oval / round bell tester (sound toy test template) is a simulation of
children's oral capacity to detect parts on the toys or toys may cause
choking or swallowing, and dangerous
Material: aluminum alloy, surface oxidation
Standard: 16 CFR 1510; ASTM F 963 4.21; EN71-1998 8.17; GB6675-2003
A.5.3
TW-204Accessibility Probes
To determine whether any part or component of a toy can be contacted by the probe.
The probe simulates the finger of the infant or child touching the accessible points or
edges of a toy, which may then be subject to tests of sharp points or sharp edges.
Accessibility probes are designed for two age groups:
Probe A for 0-36 months
Probe B for 37-96 months
Standard: 16 CFR 1500.48; 16 CFR 1500.49; EN-71; GB 6675-2003
TW-205 Small Ball
Small ball test fixture is use to examine a toy up of whether small ball accessories
may result in the child swallow, stop breath way and esophagus to cause choking
danger or not
TW-206 Small Parts Cylinder
To determine whether toys & other articles intended for use by children
under 3 years old present choking, aspiration, or ingestion hazards
because of small parts. If any objects can fit completely into the
cylinder without compressing & in any orientation, it is defined as a
"Small Part". Its internal dimensions simulate the fully expanded throat of
a child under 3 years old.
Standards: 16 CFR 1500.48, ASTM F963 4.8, EN-71 1998 8.2, ISO 8124
TW-207 Bite Test Clamp
To simulates a child biting the accessible area of toys. The part of the
toy being tested is placed in a bite test clamp & a specified force is
applied for a specified period. The toy is then tested to ascertain
whether or not any hazards result from the bite test such as sharp points/
sharp edges / small parts.
Standard: ASTM F963, 16CFR 1500.52C
TW-211Test Needle
Diameter 1MM, the top radius 0.5MM, load 5N, for leakage testing,
Standard: EN71-1; GB6675 A.5.19
Dimension Tolerance: + /-0.05mm
TW-219 Kinetic Energy Tester/Projectile Velocity Tester
To determine the size catapults kinetic energy of toys, the ejection of parts of the test
apparatus through the tube or external testing of the components of the two sensors
detect the ejection toy parts used away after a certain period of time, it has calculated
the move Energy. The main instruments used for this test launch of baby toys or
children's safety.
Clock out:1 MHz
Display:7 digit
Display rang :0.000001 to 9.999999 sec
Projectile size :Large then 2mm diameter
Small then 35mm diameter ( for internal sensor )
Sensors distance:Fixed 150mm ( internal sensor )
Adjustable :40mm - 400mm ( external sensor)
Dimensions:240mm×310mm×130mm.
Weight:16kg
Standards:16 CFR 1500 ASTM F963 4.8 EN-71 ISO 8124
TW-220 Sharp Edge Tester
Detailed parameter: The Sharp Edge Tester is used to touch to examining a toy of
position whether the existence endanger safe sharp-edged edge, belong to the test item
of the toy safety.
Dimensions: 290x180x115 mm
Weight: 1.90 kg
Standards: 16 CFR 1500.48, ASTM F963 4.8, EN-71 1998 8.2, ISO 8124
Accessories :charging unit foot switch Standard import sharp edge tape base
plate
TW-221 Sharp Point Tester
The Sharp Point Tester is use can touch to examining a toy of position
whether the existence endanger safe of sharp-edged sharp point.
Belong to the test item of the toy safety; all accessories from not the rust
material make into. It is consistent to the request of technique
parameter all countries.
Dimensions: 112× 16× 16mm ;Weight: 80 g
Standards: 16 CFR 1500.48, ASTM F963 4.8, EN-71 1998 8.14, ISO 8124
Accessories: weight, batteries, bulb 2 pieces
TW-222-A Metal Detector
Detect the metal impurity in foodstuff, textile, and chemical industry;
make sure without metal pollution, providing customer high quality.
Detect the metal impurity in plastic, textile , wood, mining industry,
protect the key equipments, reduce shut down, maintain time and
expense
Specifications: L20 L30 L40
Detect width 200mm 300 mm 400 mm
Detect hole height 30-200mm 30-300mm 30-600mm
machine height:standard 730mm
transfer speed :32 m ⁄ min;5 ∼50m/min
transfer capacity:≤1kg ≤5kg ≤1kg
warning way:
equipment ‘s width:530mm 630 mm 730mm
TW-222 Needle Detector
Can inspect the toy, finished products and ready-made clothing and
food whether to have the metal ingredient the object, may also detect
the tiny like needle's object, is to the product security check in the
essential instrument
Detecting method:Magnetic induction
Detecting height:100mm
Detecting width:600mm
Detecting ability:φ 0.8mm iron ball
Detecting adjustment:1-10 stepless adjustment
Alarm method:Buzzer LED display and the belt stops
Belt speed:(about)30m/min
Power supply:220V/50HZ
Rated output:(about)120WDimension:1650mm(1) ×1050mm(w) ×
900mm(h)mm
Weight:(about)190kg
TW-223latform
Can inspect the toy, finished products and ready-made clothing and
food whether to have the metal ingredient the object, may also detect
the tiny like needle's object, is to the product security check in the
essential instrument.
Detecting method:Magnetic induction
Detecting ability:Metal darner(0.6×33)Max:110mm
Detecting adjustment:stepless adjustment
Detecting area: 100(w) ×500(H)mm
Alarm method:Buzzer, lamp
Power supply: 220v/50Hz
Rated output:(about)20w
Dimension: 360mm(l) ×670mm(w) ×70(h)mm
Weight: (about)15kg
TW-224Nail Bed Flammable Tester
Used in the detection part of the combustion of flammable hair, and
record the time, to see whether the burning of part of the meet
flammability standards
dimension:25.4*25.4cm.;standard:ASTM F963
TW-225 Surface Flammability Tester
The surface flammability Tester commonly used in the examination down or the
superficial knowledge fabric's flammability, the flame spreads fast in the fabric
surface, but the fabric Kieb structure is incombustible.
Technical specifications:
Nozzle movement speed: 150 millimeters/second ± 5 millimeter/seconds
(bidirectional), the nozzle moves the distance: ≥300 millimeter.
May test the fabric plush altitude: 0-70mm; Flame altitude: 0-60mm continuously
adjustable.
Dimension: 600mm×400mm×370mm;
Weight: 20kg.
Power: AC220V±10% 50Hz; 50W
Standards: BS 4569, EN71
TW-226 En71 Toy Flammable Tester
It is used for testing the flammability of toys, children clothes, evaluates the following
toys flammability speed time.
Testing the child clothing or the toy and accessories’ flammability, appraises the
following toy type the rapidity of the flammability and time
The PLC control, the time is accurate, Chinese man-machine contact surface
The different test method provides different sample jig
Clamps are easy to operated
The jig may adjust willfully, suits different sample
Comply with standard EN71-2 2003
TW-227 45 degree flammability tester
45 degree flammability tester, check the flammable performance of the textile
Stainless testing room with glass window, after ignition automatic time (0.01 second
precision) automatic or
parameters:
Manual firing device, included sample holder and bush.
Spread time scope: 0-99.99s, Firing time: 1s or specified, resolution: 0.01s.
Igniter model: comply to ASTMD1230
Dimension: 400mm×300mm×500mm.
Weight: 28kg.
Power : 220V/50Hz,2A
Standards: ASTM D1230, FTMS191-5908, CFR 16-1610, CALIF TB117
TW-228 Toy Box Cover Durability Tester
Test times: 0-999, 999 times can be set
Test precision: 0-10 time/min
Display mode: Displayed by big digital liquid crystal screen
Control mode: Controlled by Micro-computer automatically
Action mode: Electromotion or Automatism
Test pieces: Stop automatically
Standards: 16 CFR 1500, ASTM F963 4.8, EN-71, ISO 8124
TW-229 Mouth Toy Endure Tester
Applications: To prevent mouth moving toys or children's mouthpiece has been
mistakenly inhaled and causes a choking hazard
Features: 1. Instruments to meet the 5s at least 295 cubic centimeters within + / -10
cubic centimeters of gas, and can be 10 times alternately blowing, suction toy.
power:220V/50Hz,4A.
dimension (L×W×H):650×400×260 mm
Weight:40kg
standards:EN71.8.17
TW-230 Sound Level Test Stand
Energy along the X, Y, Z (X displacement:0-1000MM; Y displacement of 0-1700MM;
Z displacement: 0-1800MM) slide freely positioning the three directions.
Flat with horizontal and vertical angle adjustment instructions: 0-1800;
Optical ranging device, measurement noise, the distance between the meter and toys;
Dimension (L * W * H): about 1880 * 1150 * 2200mm
Material: Aluminum
TW-232Flat Clamp
Used for assisting pull testing
TW-233Hair Claw Clamp
Special auxiliary hair pull test fixture
TW-234 Long Mouth Clamp
used for assisting pull testing
TW-235 Short Mouth Clamp
used for assisting pull testing
TW-236 Big Mouth Tension Clamp
Used for assisting pull testing
TW-237Hook set for tire removal
Pull the wheels with fixture; Material: stainless steel
TW-238 single hook set clamp
Pull the wheels with fixture; Material: stainless steel
TW-239Two claw clamp
Stainless steel, used for testing eyes, nose etc....
TW-240Three Claw Clamp
Stainless steel, used for testing eyes, nose etc....
TW-241Seam Clamp
Standards:ASTM F963 8.9.1.1, EN71-1998 8.4.2.2
TW-243 A torque clamp
Used for clamping the sample during the wrest testing
Stainless steel and aluminum, and copper
TW-243B torque clamp
Used for clamping the sample during the wrest testing
Stainless steel and aluminum, and copper
TW-246 ASTM Compression Head
ASTM Compress Head
Standard:ASTM F 963 8.10.1
EN Compression Head
Standard EN71-1998 8.8
dimension :28×28×19mm
Diameter 30 mm round rod
TW-247 Flexture Test
Used to test the toys from the increase in rigidity or fixed shape of the
metal wire or other metal materials used in the bending (or abuse) the
process, whether due to fracture a risk of a sharp tip or sharp edges
protruding. Abuse testing program is a toy. Made of stainless steel
material. United States, Europe and China national standard test board
size requirements vary.
Model: American USA Europe meet European Union
Standards: 16 CFR 1500.48 16 CFR 1500.49 EN-71
TW-248 Head Probe C
conforms to ASTM963 standard, simulate human body testing module
for opening mouth.
TW-249 Head Probe D
Details: conforms to EN71-8:2003 standard, simulate human body
testing module for opening mouth
TW-250 Infrared Thermometer
Features:
a) simple one-hand operation;
b) laser targeting;
c) LCD with back light;
d) C/F select switch;
e) laser on/off switch;
f) automatic power off;
g) display hold function
TW-251Rod
3mm、5mm、6mm、12mm
Imperial units
1、0.19in ( tolerance:0.005")
2、0.250 in ( tolerance:0.005")
3、0.50 in (tolerance:0.005")
4、0.625in ( tolerance:0.005")
Metric units
1、Ø3 ( tolerance:±0.05mm)
2、Ø5 (tolerance:±0.05mm)
3、Ø6 (tolerance:±0.05mm)
4、Ø12 (tolerance:±0.05mm
TW-252Pacifier Test
Pacifier Tester is used to detect "pacifier class" toy conforms to safety
standards
Role: testing security instruments-pacifier
Standards: 16 CFR 1511 ASTM F 963 4.22
TW-253 Handheld Metal Detector
Can inspect the toy, finished products and ready-made clothing and food whether to
have the metal ingredient the object, may also detect the tiny like needle's object, is to
the product security check in the essential instrument.
Parameters:
a) Detecting method:Magnetic induction
b) Detecting ability:Metal darner(0.75×30)
c) Detecting adjustment:40mm
d) Detecting area:60(w) ×25(D)mm
e) Alarm method:Buzzer, lamp, light
f) Power supply:9V
g) Dimension:65mm(l) ×145mm(w) ×45(h)mm
h) Weight:(about)280g
TW-257 2 m/s. Tester
This instrument is mainly used for test rides at the speed of toys 2m / s when the value
of the barrier imposed by force. Toys will be under test placed on the conveyor belt,
the drive wheel until the toy speed of 2m / s and remain stable; the display shows the
pressure sensor to the force sensing value, according to ability to judge the value of
toy safety.
Conveyor belt Speed :2m/s (can be adjusting)
Dimensions:1530x630x750mm
Weight:75kg
Standards:16 CFR 1500 ASTM F963 4.8 EN-71 ISO 8124
TW-258Button Snap Tester
Used for measuring the responsibility of garment manufacturer to ensure
button and firmware can be fixed on the ready-made garments properly,
avoiding button drop from garment to brought danger to baby swallow.
Used for testing the vertical orientation tension of button and added touch.
Parameters:
a) Dimensions : 280 x 230 x 735 mm (L×W×H)
b) Weight: 25 kg
c) Accessories:
d) 30kg Impact Force Gauge FB-30K 1Pc
f) Upper Stud Clamp 1Pc
g) Snap Clamp 1Pc
h) Lower Fabric Clamp, Lever Arm locking 1Pc
i) Three Pronged Clamp 1Pc
g) 17 Standard Pressure Clamp 17 1Pc
Standards : 16 CFR 1500.51-53, ASTM WK4510 PS79-96 , ASTM F963 ,
EN71-Part1,M&S P115A
TW-260 Sound Level Meter
The Sound Level Meter has been designed to meet the measurement
requirements for industrial safety offices and sound quality control in various
environments.
Ranges from 35dB to 130dB at frequencies between 31.5Hz and 8KHz.
Display with 0.1dB steps on a 4-digits LCD
With two weighting A and C
Both AC and DC signals output is available from a signal standard 3.5mm
coaxial socket suitable for a frequency analyzer, level recorder, FFT analyzer
graphic recorder etc.
Parameters:
a) Standard: according to IEC651, ANSI S1.4
b) Frequency range:31.5Hz~8KHz
c) Measuring level range:35~130dB
d) Frequency weighting: A/C
TW-266Mechanical Metronome
Product Features: pure metal core, precise、stable and bright volume
Tempo range: 40-208BPM
Beat tolerance: <1%
Size: 110mm×110mm×220mm
Weight: 570g
Color: black/red/white/ light coffee brown red/jade/green jade/ transparent yellow/
transparent purple
TW-267specific weight
specification:5N,10N,25N or specified by customers.
material:stainless steel
TL-404TTFPush Pull Tension Tester
It is used for providing large and steady strength during the tension testing
Most use in toy‘s damage tension testing, provide the strength by air cylinder
Parameters:
a) Push-pull intensity maximum: 188/168kgf
b) Cylinder trip maximum: 125mm
c) Adjustable speed: 50-800mm/s
d) Cylinder base plate trip: 0-500mm
e) Withstanding pressure cylinder: 13.5kgf/cm2
f) Jaw size: 90 x40 mm
g) Adjustable stroke left jaw: ± 60 mm
h) Adjustable upper and lower jaw: 0-120 mm stroke
i) Dimensions: 1620x320x420 mm
j) Weight: 80kg
Standards: 16 CFR 1500, ASTM F963 4.8, EN-71, ISO 8124
TL-405Force Gauge
With simple operation, precision, peak value maintance, indicate two scales
Application: electrics,components of Vehicle, Lighter & portfire , construction, fabric
etc.
Handheld design, compact
Easy operation
capacity:10KG,20KG,30KG,50KG
TL-409Torque Gauge
Be used to measure the product or product components to be able to bear the max
torque.
Excellent design, light in weight, easy to use, precision:+/-3%
Test range: 1-9 or 1-15kgf.cm
Min :0.2 kgf.cm