Upload
others
View
150
Download
0
Embed Size (px)
Citation preview
2
3
1
4
Compatible with these Pioneer double DIN devices
Pioneer Navigation
Installation ManualDouble DIN KitStandard: 381300-06Rubber-Touch: 391300-06
• Toyota Avensis (T25)
Double DIN Set contents
• (1) Metal Frame• (2) Installation Kit
• (3) Mounting frame• (4) Facia Plate© 12/2008 ALL RIGHTS RESERVED. Technical changes possible. No liability for misprints.
Avensis (T25) TOYOTA GENUINE AUDIO
Avensis (LHD) - 610-02
3. EINBAU DES 6 CD-WECHSLERS IM ARMATURENBRETTIN-DASH 6 CD-CHANGER INSTALLATIONINSTALLATION DU CHANGEUR 6 CD MONTE DANS LE TABLEAU DE BORD
Abb. 1 - Fig. 1
Abb. 2 - Fig. 2
1. Schalthebelknauf und Schaltungs-abdeckung mit einem Nylonhebel-werkzeug entfernen.
: Clip (4x): Nagel (4x)
1. Remove the shift knob and shiftcover using a nylon pry tool.
: Clip (4x): Nail (4x)
1. Déposez la rotule du levier de vitesseset sa garniture à lʼaide dʼun levier
en nylon.: Clip (4x): Clou (4x)
21
21
21
3. Das Schutzklebeband anbringen .
3. Attach the protection tape .
3. Fixez le ruban de protection .4
4
4
Abb. 3 - Fig. 3
2. Die Verkleidung entfernen .: Clip (5x)
2. Remove the panel .: Clip (5x)
2. Déposez le panneau .: Clip (5x)
3
3
3
12
3
4
4
Avensis (T25) TOYOTA GENUINE AUDIO
Avensis (LHD) - 610-02
3. EINBAU DES 6 CD-WECHSLERS IM ARMATURENBRETTIN-DASH 6 CD-CHANGER INSTALLATIONINSTALLATION DU CHANGEUR 6 CD MONTE DANS LE TABLEAU DE BORD
Abb. 1 - Fig. 1
Abb. 2 - Fig. 2
1. Schalthebelknauf und Schaltungs-abdeckung mit einem Nylonhebel-werkzeug entfernen.
: Clip (4x): Nagel (4x)
1. Remove the shift knob and shiftcover using a nylon pry tool.
: Clip (4x): Nail (4x)
1. Déposez la rotule du levier de vitesseset sa garniture à lʼaide dʼun levier
en nylon.: Clip (4x): Clou (4x)
21
21
21
3. Das Schutzklebeband anbringen .
3. Attach the protection tape .
3. Fixez le ruban de protection .4
4
4
Abb. 3 - Fig. 3
2. Die Verkleidung entfernen .: Clip (5x)
2. Remove the panel .: Clip (5x)
2. Déposez le panneau .: Clip (5x)
3
3
3
12
3
4
4
ab
Avensis (T25) TOYOTA GENUINE AUDIO
Avensis (LHD) - 610-02
3. EINBAU DES 6 CD-WECHSLERS IM ARMATURENBRETTIN-DASH 6 CD-CHANGER INSTALLATIONINSTALLATION DU CHANGEUR 6 CD MONTE DANS LE TABLEAU DE BORD
Abb. 1 - Fig. 1
Abb. 2 - Fig. 2
1. Schalthebelknauf und Schaltungs-abdeckung mit einem Nylonhebel-werkzeug entfernen.
: Clip (4x): Nagel (4x)
1. Remove the shift knob and shiftcover using a nylon pry tool.
: Clip (4x): Nail (4x)
1. Déposez la rotule du levier de vitesseset sa garniture à lʼaide dʼun levier
en nylon.: Clip (4x): Clou (4x)
21
21
21
3. Das Schutzklebeband anbringen .
3. Attach the protection tape .
3. Fixez le ruban de protection .4
4
4
Abb. 3 - Fig. 3
2. Die Verkleidung entfernen .: Clip (5x)
2. Remove the panel .: Clip (5x)
2. Déposez le panneau .: Clip (5x)
3
3
3
12
3
4
4
a
b
Avensis (T25) TOYOTA GENUINE AUDIO
Avensis (LHD) - 7 10-02
4. Die Audioeinheit ausbauen .: Bolzen (4x)
4. Remove the audio unit .: Bolt (4x)
4. Déposez lʼunité audio .: Boulon (4x)101
5
1015
1015
Abb. 4 - Fig. 4
6.a) Den Schalter ausbauen .b) Die Glühlampe entfernen.c) Den Stecker zum Entfernen nach
oben bewegen.
6.a) Remove the switch .b) Remove the bulb .c) Remove the connector by moving it
upward.
6.a) Déposez le commutateur .b) Déposez lʼampoule .c) Déposez le connecteur en le dépla-
çant vers le haut.27
20
26
2720
26
2720
26
Abb. 5 - Fig. 5
Abb. 6 - Fig. 6
5. Das Handschuhfach ausbauen.a) Die Haken entfernen .
: Haken (2x)b) Die Anschläge durch Ziehen nach
innen entfernen.
5. Remove the glove compartment .a) Remove the hooks .
: Hook (2x)b) Remove the stoppers by pulling
them inside.
5. Enlevez la boîte à gants .a) Déposez les crochets .
: Crochet (2x)b) Déposez les butées en les tirant vers
lʼintérieur.28
102104
6
28104
1046
28102
1046
6
104
2627
28
101
5
20
b
a
a
Installation Manual Double DIN Kit 381300-06 / 391300-06
3. Remove side panels left (a) and right (b).
All installation work must be performed by a qualified professional installer only.The manufacturer / dealer is not liable for any kind of incidential or indirect damages.
1. Remove the shift knob (a) and shift cover panel (b).
Mount the metal brackets to the double DIN head unit.
The position of the coppercoloured holder can be adjusted to your needs for perfect fit.(see sample)
(sample photo) (sample photo)
5. Place the facia plate on the dashboard. Push the metal frame into the facia plate
Connect all required circuit points and push the double DIN head unit in the metal frame until it snaps in.
Place the trim frame. Reinstall everything in reverse
order to finish installation.
2. Remove dashboard panel (a)
4. Remove the 4 screws (a) Remove the OEM head unit (b)