total valve

TOTAL PRODUCTC A T A L O G U EW A T E R | H E A T I N G | V E N T I L A T I O N | A I R C O N | G A S

O U R G E N I U S I S V A L V E S & P I P E F I T T I N G S

BALANCING VALVES

BALL VALVES

BUTTERFLY VALVES

CHECK VALVES

DRAIN COCKS

GATE VALVES

GLOBE VALVES

PIPE FITTINGS

RADIATOR VALVES

STRAINERS

CRANE FLUID SYSTEMS TOTAL PRODUCT CATALOGUE

Contents

Introduction 1

Valve Types 2

Index of Figure Numbers 36

Pipe Fittings Summary 37

HVAC Quick Selection Guide 4

Gate Valves 6

Globe Valves 12

Check Valves 15

Ball Valves 18

Butterfly Valves 20

Static Balancing Valves 23

Strainers 26

Radiator Valves 28

Drain Cocks 30

Thermal Balancing ValvesMultiTherm, EtaTherm,MultiTee, TMV’s

31

Flow Management SystemsCommPac 33

Flow Management SystemsDominator Z3000

34

FULL TECHNICAL DATA AVAILABLE ONWWW.CRANEFS.COM

1CRANE FLUID SYSTEMS

Introduction

Crane Fluid Systems

Crane Fluid Systems is a leading manufacturer of valves,fittings and engineered products in the building servicesand general industrial markets. We aim to be ourcustomers’ preferred supplier by offering products whichprovide best value together with service levels thatexceed our customers’ expectations.

Customer Service

The satisfaction of customer requirements is the definingphilosophy of Crane Fluid Systems. The position we holdin our markets is built on the foundations of productavailability from our network of distributors and providingexpert technical support to users of valves and pipefittings.

Customers’ orders are received via EDI, fax or telephoneby our Customer Service Administrators. Using our state-of-the-art computer-based Enterprise Resource PlanningSystem, we are able to immediately confirm productavailability and price. Our computers ensure orders areseamlessly transmitted to our Production Managers whoregularly review factory plans to ensure customerrequirements are satisfied on time.

Comprehensive product selection and application adviceis just a phone call away. Our Internal Sales Engineersare equipped to deal with complex valve applicationneeds, receiving customers’ drawings and producingcomprehensive valve schedules that will satisfy thedesign parameters of the heating and ventilating system.Our customers have come to regard this team as one ofthe most reliable sources of technical support.

Quality Assurance

Rigid quality control and inspection at all stages ofmanufacture ensure that Crane products are fully suitablefor their intended application and will give reliableservice. Every valve and pipe fitting is individually testedin accordance with the relevant product standard.

Crane Fluid Systems is an approved manufacturer undervarious independent quality schemes, including theBritish Standards Institution (BSI) Kitemark, and isISO9001 accredited. In addition, the company has beenapproved and/or listed by various user organisationsincluding the United Kingdom Water Fittings Bye LawsSheme (WRAS approved).

Health and Safety at Work Act

Every effort is made to ensure that when properly used, inaccordance with stated recommendations, goodssupplied are safe and without risk to health.

Should the purchaser be uncertain as to the suitability foruses other than those stated, he/she should check withthe distributor or Crane Fluid Systems' technical team.

Control of Substances Hazardous to Health

Material supplied by Crane Fluid Systems does notconstitute “substances” as defined in the approved codeof practice of COSHH but complies with the requirementsof the Health and Safety at Work Act (1974).Material supplied by Crane may be handled and stored incomplete safety.

Crane products are safe to use provided they are utilisedfor their intended function and used within the limitationsspecified by Crane.

Note: Material is defined as equipment, supplies andspares that form the subject of a contract (ref. BS 4778).

Pressure Equipment Directive

All Crane Fluid Systems products have been assessed inaccordance with the Pressure Equipment Directive (PED)97/23/EC and the Pressure Equipment Regulations 1999No. 2001. Each product has been classified into aconformity assessment category based on the intendedfluid contents – gas or liquid, the classification of theintended fluid contents – Group 1 or Group 2, themaximum allowable pressure and the nominal size (DN).

Crane products fall into either the “Sound EngineeringPractice” (SEP), Category 1, Category 2 or Category 3.According to the directive, products classified as “SEP”shall not be CE marked. Category 1 products will bear theCE mark and those products classified as Categories 2and 3 will bear the CE mark plus the number 0086. Thenumber 0086 is that of the British Standards Institute whoCrane have chosen as their “Notified Body” to monitortheir quality assurance system as required by thedirective.

2 FULL TECHNICAL DATA AVAILABLE ON WWW.CRANEFS.COM

Gate Valves

Crane gate valves offer the ultimatein dependable service whereverminimum pressure drop isimportant. They serve as efficientstop valves with fluid flow in eitherdirection.

The straight through design offerslittle resistance to flow and reducespressure drop to a minimum. Agate-like disk – actuated by a stemscrew and handwheel – moves up and down at rightangles to the path of flow, and seats against two seatfaces to shut off the flow.

Gate valves are not recommended for throttling since thecontrol characteristic is not appropriate and subsequentdamage, due to erosion, may prevent the valve providingan effective shut off.

Globe Valves

Crane globe valves are highlyefficient for throttling servicebecause seat and disk designsprovide flow characteristics withproportionate relationships betweenvalve lift and flow rate. This assuresaccurate flow control/regulation.

Globe valve bodies are normally ofspherical shape, ensuring maximumstrength against line pressures andpipeline strains. Wide faced hexagon ends on threadedvalves provide a firm wrench grip which prevents damageto the valve.

Check Valves

Check valves permit flow in onedirection only, and closeautomatically if flow reverses.They are entirely automatic inaction, depending uponpressure and velocity of flowwithin the line to perform theirfunctions of opening andclosing.

Most Crane swing check valves can be installed inhorizontal or vertical upward flow piping. Lift checkvalves must be used in horizontal lines only.

Ball Valves

The Crane range ofcopper alloy ball valvesconsists of compact,lightweight units whichare easy to install andoperate, yet their abilityto withstand robustconstruction ensureslong, trouble-free servicelife. They offer full flowwith minimum turbulence in the open position and bubbletight closure in the closed position. Only a quarter-turn isrequired to fully open or close the valve.

Butterfly Valves

Crane butterfly valves arecompact quarter turnvalves. The body iselastomer lined providing aresilient bubble tight shutoff.

The valves are supplied inwafer or lugged variantsand may be lever orgearbox operated.

Linings are EPDM or Nitrile rubber depending on theintended service conditions.

Primarily recommended for on off service, they may alsobe used for non critical throttling applications. Only aquarter turn is needed to fully open or close the valve.

Strainers

Scale and dirt in piping systemscan cause endless trouble andserious damage to pipelineequipment. Installation of Cranestrainers will help eliminate theproblems caused by foreignmatter within piping systems.

Generous proportions of Crane strainers allow the units tocollect significant quantities of foreign matter beforepressure losses necessitate cleaning of the basket.

Valve Types

Radiator Valves

Crane radiator valves aremanufactured from high-gradematerials and use the samefunctional design as the industrialbronze globe and gate valvepatterns. Considerations of theservice for which the valve isintended and also compliance withrelated standards influencesdimensions, internal detail,pressure/temperature ratings andimportantly, exterior appearance.

Crane radiator valves are suitablefor building services installationswhere durability and ruggedconstruction are predominant, whilesatisfying the aesthetic requirements demanded formodern commercial and domestic interiors.

MultiTherm/EtaTherm and MultiTee

For control of potable hot waterservices. The Muliti-Therm familyenable a constant flow in thesystem, maintaining temperatureand preventing dead-legs.

A thermostatic cartridge in theMultiTherm is factory pre-set at57ºC. Between 52ºC and 57ºC thevalve starts to close, restricting flowand increasing temperature. Whenset temperature is reached, aminimum volume flows continuouslythus preventing dead-legs forming.

During disinfection, the waterstorage temperature needs to beincreased above 62ºC and theMultiTherm opens to allowadditional flow through the system.

After disinfection, the valveautomatically returns to the pre-setposition. MultiTherm isrecommended for systems with flow rates above 0.007I/sec. EtaTherm is recommended for systems with flowrates below 0.007 I/sec. MultiTee can be fitted at variouspoints in the system to enable temperature monitoring.

The Crane ProBalance range offers a wide variety ofStatic Balancing Valves and Flow Management Systems,providing the ultimate in accuracy and reliability.

Static Balancing Valves

Established H&V practicerecommends that whereverpossible within heating and chilledwater systems, hydraulic lossesshould be minimal. Thus flowmeasurement and regulating valvesserving such systems shouldfunction with pressure losses aslow as efficient operation and highaccuracy will permit.

However, in certain circumstanceswhere flow velocities are low as aresult of system design, it isequally important that adequatedifferential pressures are availablefor accurate flow measurement. This requirement isachieved on the basis of a realistic compromise betweenthe need for accuracy and low hydraulic loss.

Crane flow measurement and regulating valves enablesystems design engineers to specify standard productionvalves which will conform to the various system designoptions arising from current H&V technology, energyconservation considerations and standards legislation.

Flow Management Systems

Alongside Crane’srange of staticbalancing valves, thecompany can alsooffer a range ofbespoke FlowManagement Systems,designed to workwithin fixed andvariable flow systems.These are prefabricated units that combine the essentialcontrol components and connecting pipework in onecompact module ready for simple and fast on-siteconnection. These systems are assembled to order fordifferent specified purposes.

VALVE TYPES


MultiTherm

EtaTherm

MultiTee

RADIATORVA

LVES

ANGLE

TRVCHROMEPLATEDBRASS

- - D885+T90

- -

TRV HEAD WITH REMOTE SENSOR

2 METRES = D889 RS2

8 METRES = D889 RS8

HANDWHEEL - - D885+T80 - -

LOCKSHIELD - - D887 - -

STRAIGHT

TRV - - D886+T90 - -

TRV HEAD REMOTE TRANSMITTER

2 METRES = D889 RT2

8 METRES = D889 RT8

HANDWHEEL - - D886+T80 - -

LOCKSHIELD - - D886 - -


ISOLATION

GATE

THREADED BRONZE D151 D151 D151 D151 D151 D151 D151X D151X D151 D151 D151 D151 - - D151 D151

THREADED DZR D151A D151A D151A D151A D151A D151A - - D151A D151A D151A D151A - - D151A D151A

FLANGED BRONZE - - DM160DM160DM160DM160DM161 DM161 - - - - - - - -

COMPRESSION BRONZE D155C - D155C - D155C - - - D155C - - - - - - -

FLANGEDCASTIRON - FM52 - FM57 - FM63 - - - - - - - - - FM52

BALL

THREADED BRONZE D171 D171 D171 D171 D171 D171 D171 D171 D171 D171 D171 D171 D171 D171 D171 D171

THREADED DZR D171A - D171A - D171A - D171A - D171A - D171A - D171A - D171A -

THREADED BRASS D191 D191 D191 D191 D191 D191 D191 D191 - - - - D191 - D191 -

COMPRESSION BRONZE D171C - D171C - D171C - - - D171C - D171C - D171C - D171C -

BUTTERFLY(See Note 2)

SEMI LUGGED

DUCTILEIRON

- -F621F621F626

F611/2F621/2F626/7

F611F621F626

F611/2F621/2F626/7

- -F621WRAS

F621/2WRAS

F621WRAS

F621/2WRAS

F611 F611/2REFERTO

CRANELUGGED WAFER - -

F614F624F628

F614/5F624/5F628/9

F614F624F628

F614/5F624/5F628/9

DM975G

DM975G

F624WRAS

F624/5WRAS

F624WRAS

F624/5WRAS

F614 F614/5

NONRE

TURN

SWINGCHECK

RESILIENT SEATBRONZE

D140 D140 D140 D140 D140 D140 D140 D140 - - - - D140 - - -

METAL SEAT D138 D138 D138 D138 D138 D138 D138 D138 - - - - D138 - D138 -

RESILIENT SEAT CASTIRON

- - - - - FM469 - - - - - - - FM469 - -

METAL SEAT - - - - - FM492 - - - - - - - - - -

WAFERCHECK

RESILIENT SEAT CASTIRON

- - -FM451FM453

-FM451FM453

FM455 FM455 - - - - - - - -

METAL SEAT - - - FM450 - FM450 - - - - - - - - - -

PIPE

LINE

PROTE

CTION

STRAINERY-TYPE

THREADED BRONZED295D297D298

-D295D297D298

-D295D297D298

-D295D297D298

-D295D297D298

-D295D297D298

-D295D297D298

-D295D297D298

-

FLANGEDCASTIRON

- - - FM276 - FM276 FM278 FM278 - - - - - FM276 - FM276

THREADEDMALLEABLE

IRONF273 - F273 - F273 - F273 - - - - - - - - -

DRAINING

DRAW OFF BALL BRONZED171

MHU

-

-

D171

MHU

-

-

D171

MHU- - -

D171

MHU-

D171

MHU- - - - -

DRAINING TAP BRONZE D340 - D340 - D340 - - - D340 - D340 - - - - -

DRAW OFF COCK BRONZE D3441/2 - D3441/2 - D3441/2 - - - D3441/2 - D3441/2 - - - - -

HVAC Quick Selection Guide

VALVE

FUNCTIONVALVE TYPE

BODY

MATERI

AL

CHILLED WATER, LTHW AND MTHWCWS DHWS

AIR/GAS(See Note 1)

OILPN6 PN10 PN16 PN25

≤50mm ≥65mm ≤50mm ≥65mm ≤50mm ≥65mm ≤50mm ≥65mm ≤50mm ≥65mm ≤50mm ≥65mm ≤50mm ≥65mm ≤50mm ≥65mm

QUICK SELECTION GUIDE


NOTES:

1) FOR AIR/GAS APPLICATIONS:-

The D191 ball valve is suitable for use on Group 1

gasses. All other products listed are only suitable for

use on Group 2 gasses.

2) ALL SEMI-LUGGED VALVES:-

F611, F621, F626, F612, F622, F627 valves are suitable for use with

flanges conforming to BSEN 1092-2 PN10 or PN16 and ANSI B16.1

Class 125 (sizes 2”-12”). Sizes 350mm to 600mm are suitable for use

with PN16 flanges only.

ALL FULLY-LUGGED VALVES:-

F614, F624, F628, F615, F625, F629 valves are suitable for use with

flanges conforming to BSEN 1092-2 PN10 or PN16. Sizes 65mm to

200mm. Sizes 250mm to 600mm are suitable for PN16 flanges only.

REGULATION DRVDOUBLE

REGULATINGVALVE

BRONZE D921/D923* -

CAST IRON - DM925G DM975G

DUCTILEIRON

- DM921

FLOWMEASUREMENT

FMD FLOWMEASUREMENT

DEVICE

DZRD901

D902*-

STAINLESS

STEEL- DM900

CIRCUITBALANCING

TWOUNIT

DRV+

FMD

DOUBLEREGULATING

VALVE+

FLOWMEASUREMENT

DEVICE

BRONZE

D921 + D901DRV FMD

-D923* + D902*DRV FMD

DUCTILEIRON

-DM921 DRVDM900 FMD

CAST IRON -DM925G DRVDM975G DRVDM900 FMD

SINGLEUNIT

FODRVFIXED ORIFICE

DOUBLEREGULATING

VALVE

BRONZED931 D981P†D933* D983P*†D934** D984P**†

-

CAST IRON - DM950G

DUCTILEIRON

- DM941/DA941

VODRV

VARIABLEORIFICEDOUBLE

REGULATINGVALVE

DUCTILEIRON

-DM931DA931

FUNCTION TYPEBODY

MATERIALTHREADED FLANGED

* LOW FLOW APPLICATIONS

** ULTRA LOW FLOW APPLICATIONS

† FOR USE WITH ACTUATOR

HVAC Quick Selection Guide

GATE VALVES


DIAGRAM DESCRIPTION SIZE FACE TO FACE WEIGHT(mm) (Kg)

Figure number: D151A 1/4" 43 0.20PN20 BSEN 12288 SERIES B 3/8" 43 0.19DZR gate valve 1/2" 50 0.23Non rising stem 3/4" 54 0.36Female threaded ends to BSEN 10226 1" 62 0.50

11/4" 70 0.8211/2" 72 1.082" 82 1.8321/2" 97 2.903" 111 3.97

Figure number: D237A 1/2" 50 0.23PN20 BSEN 12288 SERIES B 3/4" 54 0.36DZR gate valve 1" 62 0.50Non rising stem, Lockshield operated 11/4" 70 0.82Female threaded ends to BSEN 10226 11/2" 72 1.08

2" 82 1.83

DZR


Figure number: D151 1/4" 46 0.27PN20 BSEN 12288 SERIES B 3/8" 46 0.26Bronze gate valve 1/2" 51 0.27Non rising stem 3/4" 55 0.381/4"-3 version BSEN 10226 Kitemarked to BSEN 12288 1" 63 0.59Female threaded ends to BSEN 10226 or NPT 11/4" 71 0.84WRAS listed 11/2" 73 1.25

2" 83 1.8821/2" 96 4.373" 105 6.404" 162 19.7

Figure number: D237 1/2" 51 0.27PN20 BSEN 12288 SERIES B 3/4" 55 0.38Bronze gate valve 1" 63 0.59Non rising stem 11/4" 71 0.83Kitemarked to BSEN 12288 11/2" 73 1.25Female threaded ends to BSEN 10226 2" 83 1.88WRAS listed 21/2" 96 4.15

3" 105 6.24

Figure number: D155C 15mm 65 0.34PN16 BS EN 12288 SERIES B 22mm 70 0.49Bronze gate valve 28mm 76 0.75Non Rising Stem 35mm 92 1.06Compression ends to suit BSEN 1057 42mm 101 1.36table 4 R250 Half Hard Copper 54mm 125 2.37

Figure number: D255C 15mm 65 0.28PN16 BS EN12288 SERIES B 22mm 70 0.41Bronze gate valve 28mm 76 0.63Non Rising Stem, Lockshield operated 35mm 92 0.91Compression ends to suit BSEN 1057 42mm 101 1.21table 4 R250 Half Hard Copper 54mm 125 2.07

Bronze

GATE VALVES



Figure number: D151X 1/4" 46 0.27PN25 BSEN 12288 SERIES B 3/8" 46 0.26Bronze gate valve 1/2" 51 0.35Non Rising Stem 3/4" 55 0.55Female threaded ends to BSEN 10226 or NPT 1" 63 0.841/4" to 3” BSEN 10226 versions kitemarked 11/4" 71 1.18to BSEN 12288 11/2" 73 1.66

2" 83 2.5521/2" 105 4.563" 111 6.38

Figure number: D159 1/4" 46 0.36PN32 BSEN 12288 SERIES B 3/8" 46 0.35Bronze gate valve 1/2" 51 0.47Non Rising Stem 3/4" 55 0.60Female threaded ends to BSEN 10226 or NPT 1" 63 0.921/4" to 3” BSEN 10226 versions kitemarked 11/4" 71 1.41to BSEN 12288 11/2" 73 1.92

2" 83 2.7221/2" 105 5.623 111 7.89

Figure number: D235 1/2" 51 0.47PN32 BSEN 12288 SERIES B 3/4" 55 0.60Bronze gate valve 1" 63 0.92Non Rising Stem, Lockshield operated 11/4" 71 1.41Female threaded ends to BSEN 10226 or NPT 11/2" 73 1.921/2" to 3” BSEN 10226 versions kitemarked 2" 83 2.72to BSEN 12288 21/2" 105 4.90

3" 111 6.40

Figure number: D166 1/4" 46 0.32PN32 BSEN 12288 SERIES B 3/8" 46 0.31Bronze gate valve 1/2" 51 0.46Rising Stem 3/4" 55 0.72Female threaded ends to BSEN 10226 or NPT 1" 63 1.101/4" to 3” BSEN 10226 versions kitemarked 11/4" 71 1.50to BSEN 12288 11/2" 73 2.25

2" 83 3.2021/2" 108 5.803 117 8.52

Figure number: D180 1/4" 46 0.32PN32 BSEN 12288 SERIES A 3/8" 46 0.31Bronze gate valve 1/2" 51 0.46Rising Stem, Union Bonnet 3/4" 55 0.72Female threaded ends to BSEN 10226 or NPT 1" 63 1.10

11/4" 71 1.5011/2" 73 2.302" 83 3.2021/2" 108 5.803 117 8.50

Figure number: D185AT 1/2" 61 0.81PN64 3/4" 70 1.20Bronze gate valve 1" 81 1.96Rising Stem, Union Bonnet 11/4" 88 3.24Female threaded ends to NPT 11/2" 96 4.64

2" 109 7.37

Bronze (Threaded)

GATE VALVES



Figure number: DM160 20mm 89 1.57PN16 BS 5154 SERIES B 25mm 99 2.50Bronze gate valve 32mm 110 3.38Non Rising Stem 40mm 120 4.93Flanged BSEN 1092-3 50mm 135 5.54

65mm 165 8.3980mm 185 12.25

Figure number: DM161 20mm 90 1.73PN25 BS 5154 SERIES B 25mm 100 2.50Bronze gate valve 32mm 110 4.33Non Rising Stem 40mm 120 5.75Flanged BSEN 1092-3 50mm 135 7.50

65mm 165 10.8080mm 185 14.40

Figure number: D160 3/4" 83 1.52Class 100 BS 1952 SERIES B 1" 89 2.16Bronze gate valve 11/4" 102 2.86Non Rising Stem 11/2" 114 3.88Flanged BSEN 1092-3 2" 127 5.25

21/2" 140 8.393" 152 11.6

Figure number: D161 3/4" 83 1.73Class 150 BS 1952 SERIES B 1" 89 2.41Bronze gate valve 11/4" 108 3.53Non Rising Stem 11/2" 121 4.46Flanged BS 10 Table F 2" 133 6.44

21/2" 152 10.403" 171 13.10

Figure number: D162 3/4" 83 1.55Class 150 BS 5154 SERIES B 1" 89 2.18Bronze gate valve 11/4" 110 2.86Non Rising Stem 11/2" 120 4.10Flanged ANSI 150 2" 135 5.54

21/2" 165 10.223" 185 11.60

Bronze (Flanged)


Figure number: D156 1/4" 41 0.20PN16 BSEN 12288 SERIES B 3/8" 41 0.20Brass gate valve 1/2" 48 0.22Non rising stem 3/4" 54 0.35Female threaded ends to BSEN 10226 1" 62 0.52or NPT 11/4" 68 0.77

11/2" 72 1.022" 82 1.7521/2" 97 2.773" 111 3.904" 131 6.35

Brass (Threaded)

GATE VALVES



Figure number: FM52 50mm 150 14PN6 Cast Iron gate valve to BS EN 1171 65mm 170 16Bronze trim, Non rising stem 80mm 180 20Flanged ends to BSEN 1092-2 PN6 100mm 190 27

125mm 200 39150mm 210 44200mm 292 82250mm 330 123300mm 356 174

Figure number: FM57 50mm 178 14PN10 Cast Iron gate valve to BS EN 1171 65mm 190 17Bronze trim, Non rising stem 80mm 203 22Flanged ends to BSEN 1092-2 PN10 100mm 229 30

125mm 254 41150mm 267 47200mm 292 85250mm 330 146300mm 356 188

Figure number: FM63 50mm 178 17.9PN16 Cast Iron gate valve to BSEN 1171 65mm 190 20.7Bronze trim, Non rising stem 80mm 203 29.3Flanged ends to BSEN 1092-2 PN16 100mm 229 39.6

125mm 254 60.0150mm 267 77.5200mm 292 130.5250mm 330 194.5300mm 356 275.5

Figure number: FM124 65mm 190 13.5PN16 Cast Iron gate valve to BS 5163 80mm 203 18.5Non rising stem, WRAS listed 100mm 229 22.5Flanged ends to BSEN 1092-2 PN16 125mm 254 32.0

150mm 267 41.0Figure number: FM125 200mm 292 66.0As FM124 with Taper cap adapter 250mm 330 100.5Flanged ends to BSEN 1092-2 PN16 300mm 356 141.0

Figure number: F52 2" 146 13.6Class 100 Cast Iron gate valve to BS 5150 21/2" 159 15.9Bronze trim, Non rising stem 3" 165 20.0Flanged ends to BS 10 Table D or E 4" 171 27.2

5" 191 39.06" 210 44.58" 241 81.610" 273 122.912" 305 174.2

Figure number: F53 2" 178 12.7Class 125 Cast Iron gate valve to BS 5150 21/2" 190 15.8Bronze trim, Non rising stem 3" 203 19.5Flanged ends to ANSI 125 4" 229 29.3

5" 254 39.56" 267 45.88" 292 84.010" 330 148.012" 356 198.0

Figure number: F54 2" 146 13.6Class 100 Cast Iron gate valve to BS 5150 21/2" 159 15.9All iron, Non rising stem 3" 165 20.0Flanged ends to BS 10 Table D or E 4" 171 27.2

5" 191 39.06" 210 44.58" 241 81.610" 273 122.912" 305 174.2

Cast Iron (Flanged)

GATE VALVES



Figure number: F58 2" 178 17Class 125 Cast Iron gate valve to BS 5150 21/2" 190 20Bronze trim, Rising stem 3" 203 28Flanged ends to ANSI 125 4" 229 38

5" 254 566" 267 608" 356 11210" 330 18512" 356 242

Figure number: F59 2" 178 12.7Class 125 Cast Iron gate valve to BS 5150 21/2" 190 15.8Iron trim, Non rising stem 3" 203 19.5Flanged ends to ANSI 125 4" 229 29.3

5" 254 39.56" 267 45.88" 392 84.010" 330 148.0

Figure number: FM82 50mm 178 21Cast Iron gate valve to BSEN 1171 65mm 190 25Bronze trim, Rising stem 80mm 203 35Flanged ends to BSEN 1092-2 100mm 229 50

125mm 254 70150mm 267 90200mm 292 141250mm 330 223300mm 356 304

Figure number: F84 2" 178 21.5Class 125 Cast Iron gate valve to BS 5150 21/2" 190 24.8Bronze trim, Rising stem 3" 203 29.5Flanged ends to ANSI 125 4" 229 42.7

5" 254 72.36" 267 88.18" 292 140.010" 330 225.012" 356 314.0

Cast Iron (Flanged)


Figure number: F174 1/2" 52 0.8PN16 Malleable Clamp gate valve 3/4" 59 1.1Bronze trim, Rising stem 1" 65 1.6Threaded NPT 11/4" 73 2.6Sizes 21/2-4” PN12 11/2" 80 3.2

2" 92 5.121/2" 105 9.03" 116 10.54" 141 23.7

Figure number: F179 1/2" 52 0.8PN16 Malleable Clamp gate valve 3/4" 59 1.1Iron trim, Rising stem 1" 65 1.6Threaded to BS 21 11/4" 73 2.6Sizes 21/2-4” PN12 11/2" 80 3.2

2" 92 5.121/2" 105 9.03" 116 10.54" 141 23.7

Figure number: F182 1/2" 52 0.8PN16 Malleable Clamp gate valve 3/4" 59 1.1Iron trim, Rising stem 1" 65 1.6Threaded NPT 11/4" 73 2.6Sizes 21/2-4” PN12 11/2" 80 3.2

2" 92 5.121/2" 105 9.03" 116 10.54" 141 23.7

Malleable Iron (Threaded)

GATE VALVES



Figure number: F183 1" 81 2.5Iron trim, Rising stem 11/2" 95 4.6Flanged to ANSI Class 125 2" 108 6.5

21/2" 125 10.03" 129 14.54" 172 27.0

Malleable Iron (Flanged)


Figure number: 47XU-F 2" 178 21Class 150 Carbon Steel Gate Valve to API 600 21/2" 191 32Outside screw and yoke 3" 203 35Flexible Wedge Disk 4" 229 50Carbon Steel to ASTM 216 Grade WCB 6" 267 80

8" 292 14110" 330 20712" 356 29514" 381 39116" 406 50918" 432 63620" 457 96624" 508 1418

Figure number: 33XU-F 2" 216 34Class 300 Carbon Steel Gate Valve to API 600 21/2" 241 36Outside screw and yoke 3" 282 49Flexible Wedge Disk 4" 305 75Carbon Steel to ASTM 216 Grade WCB 6" 403 145

8" 419 22710" 457 34512" 502 46414" 762 62716" 838 89118" 914 111420" 991 176824" 1143 2860

Figure number: 76XU-F 2" 292 38Class 600 Cast Steel Gate Valve to API 600 21/2" 330 59Outside screw and yoke 3" 356 73Flexible wedge disc 4" 432 136Carbon Steel to ASTM 216 Grade WCB 6" 559 290

8" 660 49010" 788 70312" 838 953

Cast Steel

GLOBE VALVES



Figure number: D4 1/4" 44 0.23PN20 BS 5154 SERIES B 3/8" 44 0.22Bronze globe valve 1/2" 55 0.31Metal disc, Screwed bonnet 3/4" 63 0.42Female threaded ends to BS 21 or NPT 1" 77 0.711/4" to 2” BS 21 versions kitemarked 11/4" 91 1.12

11/2" 98 1.502" 118 2.48

Figure number: D7 1/4" 52 0.50PN32 BS 5154 SERIES B 3/8" 52 0.49Bronze globe valve 1/2" 62 0.73Renewable disc, Union bonnet 3/4" 74 1.09Female threaded ends to BS 21 or NPT 1" 90 1.741/4" to 3” BS 21 versions kitemarked 11/4" 100 2.44

11/2" 115 3.322" 136 5.5421/2" 184 10.903" 210 16.40

Figure number: D14 1/4" 52 0.39PN32* BS 5154 SERIES A 3/8" 52 0.38Bronze globe valve 1/2" 62 0.54Metal disc, Screwed bonnet 3/4" 74 0.65Female threaded ends to BS 21 or NPT 1" 90 0.90

11/4" 100 1.5811/2" 115 2.06

*21/2" & 3" rated PN25 2 136 3.3121/2" 166 5.903" 190 10.30

Figure number: D15 1/4" 52 0.40PN32* BS 5154 SERIES B 3/8" 52 0.39Bronze globe valve 1/2" 62 0.54Renewable disc, Screwed bonnet 3/4" 74 0.65Female threaded ends to BS 21 or NPT 1" 90 0.811/4" to 3” BS 21 versions kitemarked 11/4" 100 1.55

11/2" 115 2.01*21/2" & 3" rated PN25 2 136 3.08

21/2" 166 6.103" 190 10.50

Figure number: D16 1/4" 52 0.33PN32* BS 5154 SERIES A 3/8" 52 0.31Bronze globe valve 1/2" 62 0.80Renewable disc, Screwed bonnet 3/4" 74 1.24Stainless steel seat and disc 1 90 1.50Female threaded ends to BS 21 or NPT 11/4" 100 1.70

11/2" 115 2.16*21/2" & 3" rated PN25 2 136 3.67

Figure number: D46 1/4" 59 0.56PN40 BS 5154 SERIES A 3/8" 59 0.55Bronze globe valve 1/2" 68 0.80Renewable disc, Union bonnet 3/4" 81 1.24Stainless steel seat and disc 1" 95 1.82Female threaded ends to BS 21 or NPT 11/4" 108 2.73

11/2" 121 3.782" 146 6.03

Figure number: D52 1/2" 75 1.00PN64 Bronze globe valve 3/4" 89 1.51Renewable disc, Union bonnet 1" 105 2.25Stainless steel seat and disc 11/4" 121 3.59Female threaded ends to BS 21 or NPT 11/2" 133 5.05

2" 162 8.50

Bronze (Threaded)

GLOBE VALVES



Figure number: D71 1/8" 29 0.13PN32 BS 5154 SERIES B 1/4" 39 0.15Bronze needle globe valve 3/8" 45 0.21Straight pattern, Screwed bonnet 1/2" 51 0.29Female threaded ends to BS 21 or NPT 3/4" 58 0.46

Figure number: D72 1/8" - 0.13PN32 BS 5154 SERIES B 1/4" - 0.15Bronze needle globe valve 3/8" - 0.21Angle pattern, Screwed bonnet 1/2" - 0.29Female threaded ends to BS 21 or NPT 3/4" - 0.46

Bronze (Threaded)


Figure number: DM6 15mm 80 1.24PN16 BS 5154 SERIES B 20mm 90 1.76Bronze globe valve 25mm 100 2.30Renewable disc, Screwed bonnet 32mm 110 2.82Flanged ends to BS EN 1092-3 40mm 120 5.22

50mm 135 5.71

Figure number: DM11 15mm 108 1.71PN25 BS 5154 SERIES B 20mm 117 2.18Bronze globe valve 25mm 127 3.29Renewable disc, Union bonnet* 32mm 146 4.93Flanged ends to BS EN 1092-3 40mm 159 6.28

50mm 190 9.7465mm 216 16.20

*sizes 65mm & 80mm Bolted bonnet 80mm 254 21.60

Bronze (Flanged - Metric)


Figure number: D10 1/2" 108 1.76Class 150 BS 5154 SERIES B 3/4" 117 1.95Bronze globe valve 1" 127 3.20Renewable disc, Union bonnet* 11/4" 146 4.54Flanged ends to ANSI 150 11/2" 159 6.12

2" 190 8.6721/2" 216 14.90

*sizes 21/2" & 3" Bolted bonnet 3" 254 20.10

Bronze (Flanged - ANSI)

GLOBE VALVES


Diagram Description Size Face to Face Weight(mm) (Kg)

Figure number: FM369 50mm 203 24.2PN16 Cast Iron globe valve to BSEN 13789 65mm 216 29.0Bronze trim, Outside screw and yoke 80mm 241 36.9Flanged ends to BSEN 1092-2 PN16 100mm 292 56.0

125mm 330 72.3150mm 356 98.8

Figure number: F372 2" 203 23.1Class 125 Cast Iron globe valve to BS 5152 21/2" 216 27.2Bronze trim, Outside screw and yoke 3" 241 34.5Flanged ends to ANSI 125 4" 292 54.4

5" 330 70.86" 356 95.3

Cast Iron (Flanged)


Figure number: F254 1/2" 71 0.74PN64 Malleable Iron globe valve 3/4" 84 1.14Renewable disc, Screwed bonnet 1" 99 1.71Stainless steel seat, Nickel alloy disc 11/4" 112 2.67Female threaded ends NPT 11/2" 125 3.63

2" 152 5.74

Malleable Iron (Threaded)


Figure number: 143XU 2" 203 24Class 150 Carbon Steel Globe Valve to BS 1873 21/2" 216 32Outside screw and yoke 3" 241 41Bolted bonnet 4" 292 65Carbon Steel to ASTM 216 Grade WCB 6" 419 112

8" 495 17810" 622 27512" 699 409

Figure number: 151XU 2" 267 34Class 300 Carbon Steel Globe Valve to BS 1873 21/2" 292 45Outside screw and yoke 3" 318 60Bolted Bonnet 4" 356 95Carbon Steel to ASTM 216 Grade WCB 6" 445 200

8" 559 31510" 622 45812" 711 500

Figure number: 171XU 2" 292 40Class 600 Cast Steel Globe Valve to BS 1873 21/2" 330 57Outside screw and yoke 3" 356 73Bolted Bonnet 4" 432 123Carbon Steel to ASTM 216 Grade WCB 6" 559 250

8" 660 454

Cast Steel

CHECK VALVES



Figure number: F201 1/2" 70.1 0.43PN64 Malleable Iron swing check valve 3/4" 83.3 0.65Regrindable disc and seat, screwed cap 1" 102.9 1.11Female threaded ends NPT 11/4" 120.4 1.30

11/2" 137.2 2.612" 168.1 4.51

Malleable Iron


Figure number: D138 3/8" 48 0.19PN25 BS 5154 SERIES B 1/2" 58 0.32Bronze swing check valve 3/4" 66 0.43Metal disk, screwed cap 1" 80 0.61Kitemarked to BS 5154 11/4" 89 1.01Female threaded ends to BS 21 or NPT 11/2" 95 1.34

2" 108 2.1221/2" 155 4.083" 190 5.76

Figure number: D140 1/2" 58 0.33PN25 BS 5154 SERIES B 3/4" 66 0.43Bronze swing check valve 1" 80 0.63Resilient disk, screwed cap 11/4" 89 1.01Kitemarked to BS 5154 11/2" 95 1.34Female threaded ends to BS 21 or NPT 2" 108 2.12

21/2" 153 4.203" 188 6.02

Figure number: D104 1/2" 55 0.24PN20 BS 5154 SERIES B 3/4" 63 0.35Bronze lift check valve 1" 77 0.60Metal disk, screwed cap 11/4" 91 0.97Female threaded ends to BS 21 or NPT 11/2" 98 1.26

2" 118 2.09

Figure number: D116 1/4" 59 0.37PN32 BS 5154 SERIES B 3/8" 59 0.36Bronze lift check valve 1/2" 68 0.51Renewable disc, Union cap 3/4" 81 0.85Female threaded ends to BS 21 or NPT 1" 95 1.32

11/4" 108 1.9711/2" 121 2.652" 146 4.4421/2" 184 9.003" 210 13.60

Figure number: D142 1/4" 54 0.26PN32 BS 5154 SERIES A 3/8" 54 0.25Bronze swing check valve 1/2" 62 0.39Regrindable disc, screwed cap 3/4" 76 0.62Female threaded ends to BS 21 or NPT 1" 94 1.07

11/4" 110 1.6511/2" 126 2.562" 152 4.0521/2" 186 6.403" 218 9.30

Bronze

CHECK VALVES



Figure number: FM450 50mm 43 1.3PN16 Cast Iron wafer check valve 65mm 46 1.8Bronze trim 80mm 49 2.6Fits between BSEN 1092-2 PN10/16 flanges 100mm 56 4.7BS 10 Table D or E and ANSI 125 flanges 125mm 64 7.0

150mm 70 9.8200mm 71 15.0250mm 76 20.0300mm 83 30.0

Figure number: FM451 50mm 43 1.3PN16 Cast Iron wafer check valve 65mm 46 1.8Bronze trim, Resilient seated 80mm 49 2.6Fits between BSEN 1092-2 PN10/16 flanges 100mm 56 4.7BS 10 Table D or E and ANSI 125 flanges 125mm 64 7.0

150mm 70 9.8200mm 71 15.0250mm 76 20.0300mm 83 30.0

Figure number: FM453 50mm 54 1.8PN16 Cast Iron Double door wafer check valve 65mm 54 2.4to BS EN 12334 80mm 57 3.2Suitable for fitting between flanges confoming to 100mm 64 4.8BS EN 1092-2 PN16 BS10 Tabled or E and ANSI 125 125mm 70 7.3flanges 150mm 76 10.1

200mm 95 14.2250mm 108 23.6300mm 143 37.6350mm 184 60400mm 191 77450mm 203 99500mm 213 115600mm 222 231.5

Figure number: FM455 50mm 54 2.5PN25 Cast Iron Double door wafer check valve 65mm 54 3.5to BS EN 12334 80mm 57 4.5Stainless steel disc, EPDM seat 100mm 64 8.0Suitable for fitting between flanges conforming 125mm 70 10.0to BSEN 1092-2 PN25 150mm 76 13.0

200mm 95 28.0250mm 108 45.0300mm 143 68.0

Figure number: FM469 50mm 203 11.3PN16 Cast Iron swing check valve 65mm 216 15.6to BSEN 12334 80mm 241 19.3Bronze trim, Resilient seated 100mm 292 26.6Flanged ends to BSEN 1092-2 PN16 125mm 330 44.0

150mm 356 55.5200mm 495 119.0250mm 622 175.0300mm 698 263.0

Figure number: FM492 50mm 203 11.3PN16 Cast Iron swing check valve 65mm 216 15.6to BSEN 12334 80mm 241 19.3Bronze trim 100mm 292 26.6Flanged ends to BSEN 1092-2 PN16 125mm 330 44.0

150mm 356 55.5200mm 495 119.0250mm 622 175.0300mm 698 263.0

Cast Iron

NEW

NEW

CHECK VALVES



Figure number: F491 2" 203 11.3Class 100 Cast Iron swing check valve 21/2" 216 15.6to BS 4090 3" 241 19.3Bronze trim 4" 292 26.6Flanged to BS 10 table D or E 5" 330 44.0

6" 356 55.58" 495 119.0

Figure number: F493 2" 203 11.3Class 125 Cast Iron swing check valve 21/2" 216 15.6to BS 5153 3" 241 19.3Bronze trim 4" 292 26.6Flanged to ANSI 125 5" 330 44.0

6" 356 55.58" 495 119.010" 622 175.012" 698 263.0

Cast Iron


Figure number: 147XU 2" 203 15Class 150 Carbon Steel Check Valve to BS 1868 21/2" 216 26Swing check valve, Bolted cap 3" 241 27Carbon Steel to ASTM 216 Grade WCB 4" 292 42

6" 356 758" 495 12510" 622 20012" 699 30914" 787 43216" 864 55718" 978 77320" 978 84124" 1295 1318

Figure number: 159XU 2" 267 21Class 300 Carbon Steel Check Valve to BS 1868 21/2" 292 30Swing check valve, Bolted cap 3" 318 39Carbon Steel to ASTM 216 Grade WCB 4" 356 70

6" 445 1268" 533 19110" 622 29112" 711 45514" 838 70516" 864 77318" 978 100020" 1118 127324" 1346 1660

Figure number: 175XU 2" 292 28Class 600 Cast Steel Swing Check Valve to 21/2" 330 38BS 1868, Bolted cap 3" 356 52Carbon Steel to ASTM 216 Grade WCB 4" 432 87

6" 559 2258" 660 35410" 787 63512" 838 794

Cast Steel

BALL VALVES



Figure number: D171A 1/4" 45.3 0.15PN25 DZR ball valve, lever operated 3/8" 45.3 0.14PTFE seats and stem seal 1/2" 58.5 0.21Female threaded ends to BSEN 10226 Taper 3/4" 67 0.30or ANSI B1.20.1 1" 80.5 0.51WRAS Listed 11/4" 94.5 0.89

11/2" 102.5 1.29Extension stems, Lockshields or T-handles 2" 122.5 2.24can be fitted to Crane ball valves on request

Figure number: D171AC 15mm 66.5 0.21PN16 DZR ball valve, lever operated 22mm 80 0.37PTFE seats and stem seal 28mm 92.5 0.61Compression ends to BS EN 1254-2 35mm 104.5 1.00WRAS Listed 42mm 122 1.55

54mm 141 2.54Extension stems, Lockshields or T-handlescan be fitted to Crane ball valves on request

DZR


Figure number: D191 1/4" 48 0.13PN25 Brass ball valve, lever operated 3/8" 48 0.13PTFE seats and stem seal 1/2" 56 0.25Female threaded ends to BSEN 10226 Taper 3/4" 67 0.35or NPT 1" 77 0.591/4"-2" British Gas certified 11/4" 92 0.89

11/2" 103 1.342" 122 2.04

Extension stems, Lockshields or T-handles 21/2" 153 3.96can be fitted to Crane ball valves on request 3" 179 5.89

4" 212 9.35

Brass

NEW

NEW

BALL VALVES



Figure number: D171 1/4" 46 0.15PN25 Bronze ball valve, lever operated 3/8" 46 0.15PTFE seats and stem seal 1/2" 57 0.22Female threaded ends to BSEN 10226 Taper 3/4" 67 0.45or NPT 1" 77 0.69WRAS listed 11/4" 91 1.12

11/2" 103 1.67Extension stems, Lockshields or T-handles 2" 122 2.93can be fitted to Crane ball valves on request 21/2" 153 4.98

3" 179 8.75

Figure number: D171C 15mm 80 0.27PN16 Bronze ball valve, lever operated 22mm 84 0.51PTFE seats and stem seal 28mm 95 0.78Compression ends 35mm 111 1.19WRAS listed 42mm 124 1.82

54mm 149 3.28Extension stems, Lockshields or T-handlescan be fitted to Crane ball valves on request

Figure number: D171MHUPN25 Bronze ball valve, Lever operated 1/2" 104 0.27Male x hose union outlet 3/4" 124 0.55WRAS listed 1" 147 0.88Male threaded ends to BSEN 10226 Taper

Figure number: D171MHULSPN25 Bronze ball valve, Lockshield operated 1/2" 104 0.31Male x hose union outlet 3/4" 124 0.58WRAS listed 1" 147 0.90Male threaded ends to BSEN 10226 Taper

Bronze

BUTTERFLY VALVES



Figure number: F611 50mm 44 3PN16 Semi Lugged Butterfly valve 65mm 48 4to EN 593 80mm 48 5Aluminium Bronze disc, Nitrile liner 100mm 54 7-10 to 90 Deg C 125mm 57 8Lever operated (lockable) 150mm 57 9Fits between BSEN 1092-2 PN10/16 flanges 200mm 63 15and ANSI 125 flanges

Figure number: F612 50mm 44 7PN16 Semi Lugged Butterfly valve 65mm 48 8to EN 593 80mm 48 9Aluminium Bronze disc, Nitrile liner 100mm 54 10-10 to 90 Deg C 125mm 57 17Gearbox operated 150mm 57 18Fits between BSEN 1092-2 PN10/16 flanges 200mm 63 25sizes 350mm to 600mm PN16 only 250mm 70 31sizes 50-300mm fit between 300mm 79 44ANSI 125 flanges 350mm 79 60

400mm 89 93450mm 108 112500mm 113 156600mm 156 251

Figure number: F614 50mm 44 3PN16 Fully Lugged Butterfly valve 65mm 48 4to EN 593 80mm 48 6Aluminium Bronze disc, Nitrile liner 100mm 54 12-10 to 90 Deg C 125mm 57 13Lever operated (lockable) 150mm 57 14Fits between BSEN 1092-2 PN16 flanges 200mm 63 22

Figure number: F615 50mm 44 7PN16 Fully Lugged Butterfly valve 65mm 48 8to EN 593 80mm 48 10Aluminium Bronze disc, Nitrile liner 100mm 54 16-10 to 90 Deg C 125mm 57 25Gearbox operated 150mm 57 26Fits between BSEN 1092-2 PN16 flanges 200mm 63 34

250mm 70 43300mm 79 57350mm 79 88400mm 89 124450mm 108 165500mm 113 225600mm 156 313

Nitrile Liner

Crane Butterfly valves are also available to suit ANSI 125 end connections. Consult Crane for details.

BUTTERFLY VALVES



Figure number: F621 50mm 43 2.0PN16 Semi Lugged Butterfly valve to EN593 65mm 46 2.7Aluminium Bronze disc, EPDM liner 80mm 46 3.3(WRAS listed) -10 up to 100 Deg C 100mm 52 5.1Lever operated (lockable) 125mm 56 6.1Fits between BSEN 1092-2 PN6/10/16 flanges 150mm 56 8.8

200mm 60 12.9

Figure number: F622 50mm 43 3.0PN16 Semi Lugged* Butterfly valve to EN593 65mm 46 3.7Aluminium Bronze disc, EPDM liner 80mm 46 4.3WRAS listed to 300mm -10 to 100 Deg C 100mm 52 5.9Gearbox operated 125mm 56 7.1Fits between BSEN 1092-2 PN6/10/16 flanges 150mm 56 10.8sizes 250 & 300mm PN10/16 and 200mm 60 14.9350 to 600mm PN16 250mm 68 26.4

300mm 78 40.0350mm 78 73.0400mm 102 92.0450mm 114 138.0

* sizes 250mm to 600mm are wafer pattern 500mm 127 179.0600mm 154 260.0

Figure number: F624 50mm 43 2.95PN16 Fully Lugged Butterfly valve to EN593 65mm 46 3.50Aluminium Bronze disc, EPDM liner 80mm 46 5.00(WRAS listed) -10 to 100 Deg C 100mm 52 6.20Lever operated (Lockable) 125mm 56 9.50Fits between BSEN 1092-2 PN16 flanges 150mm 56 12.00

200mm 60 26.00

Figure number: F625 50mm 43 3.95PN16 Fully Lugged Butterfly valve to EN593 65mm 46 4.50Aluminium Bronze disc, EPDM liner 80mm 46 6.00(WRAS listed up to 300mm) -10 to 100 Deg C 100mm 52 7.00Gearbox operated 125mm 56 10.50Fits between BSEN 1092-2 PN16 flanges 150mm 56 18.00

200mm 60 35.00250mm 68 49.00300mm 78 56.00350mm 78 85.00400mm 102 116.00450mm 114 163.00500mm 127 203.00600mm 154 280.00

EPDM Liner – WRAS Listed


BUTTERFLY VALVES



Figure number: F626 50mm 44 3PN16 Semi Lugged Butterfly valve to EN593 65mm 48 4Aluminium Bronze disc, EPDM liner 80mm 48 5(High temperature) -10 to 130 Deg C 100mm 54 7Lever operated (lockable) 125mm 57 8Fits between BSEN 1092-2 PN10/16 flanges 150mm 57 9and ANSI 125 flanges 200mm 63 15

Figure number: F627 50mm 44 7PN16 Semi Lugged Butterfly valve to EN593 65mm 48 8Aluminium Bronze disc, EPDM liner 80mm 48 9(High temperature) -10 to 130 Deg C 100mm 54 10Gearbox operated 125mm 57 17Fits between BSEN 1092-2 PN10/16 flanges 150mm 57 18sizes 350-600mm PN16 only 200mm 63 25sizes 50-300mm fit between ANSI 125 flanges 250mm 70 31

300mm 79 44350mm 79 60400mm 89 93450mm 108 112500mm 133 156600mm 156 251

Figure number: F628 50mm 44 3PN16 Fully Lugged Butterfly valve to EN593 65mm 48 4Aluminium Bronze disc, EPDM liner 80mm 48 6(High temperature) -10 to 130 Deg C 100mm 54 12Lever operated (lockable) 125mm 57 13Fits between BSEN 1092-2 PN16 flanges 150mm 57 14

200mm 63 22

Figure number: F629 50mm 44 7PN16 Fully Lugged Butterfly valve to EN593 65mm 48 8Aluminium Bronze disc, EPDM liner 80mm 48 10(High temperature) -10 to 130 Deg C 100mm 54 16Gearbox operated 125mm 57 25Fits between BSEN 1092-2 PN16 flanges 150mm 57 26

200mm 63 34250mm 70 43300mm 79 57350mm 79 88400mm 89 124450mm 108 165500mm 113 225600mm 156 313

EPDM Liner – High Temperature


STATIC BALANCING VALVES



Figure number: D901 1/2" 57 0.26DZR Flow measurement device to 3/4" 58 0.31PN25 (Max temp 120°C) 1" 66 0.39Threaded Female inlet & Male outlet 11/4" 72 0.51BSEN 10226 11/2" 72 0.52Size 1/2" includes complimentary copper 2" 82 0.81to iron adapterFitted with two insertion test points 1/2" 57 0.26Figure number: D902As D901 but designed for low flow applications

Figure number: DM900 20mm 18 0.7PN 25 (Max temp 120°C) 25mm 18 0.8Stainless Steel Flow measurement device 32mm 18 1.0Wafer pattern to fit between 40mm 18 1.1BSEN 1092-2 PN10/16 Flanges 50mm 18 1.4Fitted with two insertion test points 65mm 18 1.5

80mm 18 1.8100mm 18 2.2

* larger sizes available please consult Crane 125mm 18 2.6150mm 18 3.0200mm 18 4.4250mm 18 5.7300mm* 18 7.1

Flow Measurement Devices

Double Regulating Valves


Figure number: D921 WRAS listed 1/2" 87 0.65Bronze double regulating valve to 3/4" 96 0.72BS 7350 PN25 (Max temp 120°C) 1" 100 0.91Threaded Female BSEN 10226 or NPT 11/4" 114 1.10

11/2" 125 1.442" 146 1.90

Figure number: D923 WRAS listedAs D921 but designed for low flow 1/2" 87 0.65applications

Figure number: DM921 65mm 290 15.8PN16 Ductile Iron double regulating 80mm 310 19.5globe type valve to BS 7350 100mm 350 28.0Flanged to BSEN 1092-2 PN16 125mm 400 37.5

150mm 480 50.5200mm 600 123.0250mm 730 192.0300mm 850 251.0

Figure number: DM925G 50mm 43 8.6PN16 Cast Iron double regulating fully 65mm 46 9.1lugged butterfly valve to BSEN 593 80mm 46 11.8Al. Bronze disk and EPDM liner 100mm 52 17.2Gearbox operated 125mm 56 18.1Fits between BSEN 1092-2 PN16 Flanges 150mm 56 19.5

200mm 60 29.5250mm 68 39.9

Lever version DM925L 300mm 78 54.9

Figure number: DM975G 50mm 43.0 10.0PN25 Ductile Iron double regulating fully lugged 65mm 45.0 10.8butterfly valve to BSEN 593 80mm 46.0 11.0Stainless steel disc and EPDM liner 100mm 51.5 13.0Gearbox operated 125mm 56.0 16.0For use with PN25 flanges 150mm 56.5 18.5

200mm 60.0 29.8250mm 68.5 40.0300mm 79.5 53.0




Figure number: D981P 1/2" 87 0.41PN16 Bronze commissioning set 3/4" 96 0.45(Max temp 120°C)Threaded Female BSP or NPTFitted with two insertion test points

Figure number: D983P 1/2" 87 0.41As D981 but designed for low flowapplications

Figure number: D984P 1/2" 87 0.41As D981 but designed for ultra low flowapplications

Motobalance Fixed Orifice Double Regulating Valve(Commissioning Set)


Figure number: D931 1/2" 87 0.65PN25 Bronze commissioning set to BS 7350 3/4" 96 0.72(Max temp 120°C) 1" 100 0.91Threaded Female BSEN 10226 or NPT 11/4" 114 1.10Fitted with two insertion test points 11/2" 125 1.44WRAS listed 2" 146 1.90

Figure number: D933 1/2" 87 0.65As D931 but designed for low flowapplicationsWRAS listed

Figure number: D934 1/2" 87 0.65As D931 but designed for ultra low flowapplicationsWRAS listed

Figure number: DM941 65mm 290 16.3PN16 Ductile Iron double regulating globe type 80mm 310 20.0valve to BS 7350 (Max temp 120°C) 100mm 350 28.5with integral fixed orifice 125mm 400 38.0Flanged to BSEN 1092-2 PN16 150mm 480 51.0Fitted with two insertion test points 200mm 600 124.0Figure number: DA941 250mm 730 194.0Flanged to ANSI 125 300mm 850 254.0

Figure number: DM950G 50mm 158 19.7PN16 Cast Iron butterfly valve 65mm 161 20.8commissioning set 80mm 171 23.4Al. Bronze disk and EPDM liner 100mm 181 32.5(Max temp 120°C) 125mm 190 38.4Double regulating gearbox operated 150mm 232 47.1Flanged to BSEN 1092-2 PN16 200mm 287 67.8

250mm 345 89.2Lever version DM950L 300mm 404 124.2

350mm 451 166.5400mm 511 180.0

Fixed Orifice Double Regulating Valve(Commissioning Set)




Figure number: DM931 65mm 290 15.8PN16 Ductile Iron variable orifice 80mm 310 19.5double regulating valve to BS 7350 100mm 350 28.0(Max temp 120°C) 125mm 400 37.5Flanged to BSEN 1092-2 PN16 150mm 480 50.5Fitted with two insertion test points 200mm 600 123.0

250mm 730 192.0Figure number: DA931 Flanged ANSI 125 300mm 850 251.0

Variable Orifice Double Regulating Valve


Figure number: P82 1/4" - -Insertion test point for MTHW

Figure number: P83 1/4" - -Extension tube for use on insulated systems.

Figure number: P84 1/4" - -Insertion test point, pack of 10

Compression ends D921, D923, D931, D933, D934, D981P, D983P, D984P, whenconnecting to copper pipe in accordance with BSEN1057 table 4. (R250 Half Hard Copper).

1/2” (15mm) Kit = Part No 0JG91118S 3/4” (22mm) Kit = Part No 0JG9119T

Balancing Valve Accessories

P83

P82P84

STRAINERS



Figure number: D295 1/2" 74.5 0.27PN25 Bronze Y Type strainer 3/4" 86.5 0.43Stainless steel perforated screen 0.75mm 1" 108 0.79Stainless steel perforated screen 0.75mm 11/4" 122 1.1Female threaded ends to BSEN 10226 or NPT 11/2" 135 1.58WRAS Listed 2" 163 2.55

Figure number: D297 1/2" 71 0.38PN32 Bronze Y Type strainer 3/4" 86 0.63Stainless steel perforated screen 0.75mm 1" 101 0.96Female threaded ends to BSEN 10226 or NPT 11/4" 134 1.81WRAS Listed 11/2" 148 2.43

2" 176 4.13

Figure number: D298 1/2" 58 0.18PN16 Bronze Y Type strainer 3/4" 70 0.29Stainless steel perforated screen 0.75mm 1" 88 0.39Female threaded ends to BSEN 10226 or NPT 11/4" 96 0.68WRAS Listed 11/2" 107 0.93

2" 126 1.5

Bronze


Figure number: FM276 50mm 226 13.0PN16 Cast Iron Y Type strainer 65mm 290 23.0Stainless steel perforated screen 1.5mm 80mm 306 30.0Flanged ends to BSEN 1092-2 PN16 100mm 350 43.0Drilled bosses and cap 125mm 399 71.0*Sizes 350 to 600mm available 150mm 480 93.0on request 200mm 600 161.0

250mm 686 266.0300mm 757 397.0

Figure number: F277 2" 152 13ANSI 125 Cast Iron Y Type strainer 21/2" 178 23Stainless steel perforated screen 1.5mm 3" 191 30Drilled bosses and cap 4" 229 43Flanged ends to ANSI Class 125 5" 254 71

6" 279 938" 342 16110" 406 26612" 483 397

Cast Iron

*< 300mm = Group 2 gases (including steam)Group 1 and 2 liquids

> 300mm = Group 1 and 2 liquids only

NEW

NEW

STRAINERS



Figure number: FM278 50mm 230 12.0PN25 Ductile Iron Y Type strainer 65mm 273 25.0Stainless steel perforated screen 1.6mm 80mm 295 33.0Flanged ends to BSEN 1092-2 PN25 100mm 352 43.0

125mm 416 73.0150mm 470 97.0200mm 543 164.0250mm 660 270.0300mm 770 400.0

Ductile Iron


Figure number: F273 1/2" 74 0.37PN64 Malleable Iron Y Type strainer 3/4" 89 0.54Stainless steel perforated screen 0.75mm 1" 104 0.92Female threaded ends to BSEN 10226 11/4" 137 1.55

11/2" 150 2.222" 178 4.17

Malleable Iron

*< 300mm = Group 2 gases (including steam)Group 1 and 2 liquids

> 300mm = Group 1 and 2 liquids only

RADIATOR VALVES


DIAGRAM DESCRIPTION SIZE WEIGHT(Kg)

Figure number: D885 15mm -PN10 Angle pattern TRV and Wheel Head valve body 22mm -

Figure number: D886 15mm -PN10 Straight pattern TRV and Wheel Head valve body 22mm -

Figure number: T80 - -Wheel Head - -

Figure number: T90 - -TRV Head - -

D885 Angle Body and T90 TRV Head 15mm 0.35022mm 0.519

D886 Straight Body and T90 TRV Head 15mm 0.39122mm 0.580

D885 Angle Body and T80 Wheel Head 15mm 0.35022mm 0.519

D886 Straight Body and T80 Wheel Head 15mm 0.39122mm 0.580

TRV & Wheel Head Connected to Common Valve Body.Chrome Plated Finish

RADIATOR VALVES



Figure number: D887 15mm 0.232PN10 Angle pattern Lockshield valve 22mm 0.387

Figure number: D888 15mm 0.273PN10 Straight pattern Lockshield valve 22mm 0.455

Lockshield Valves. Chrome Plated Finish


Figure number: D889 RS2 2m -Remote sensing TRV sensor

Figure number: D889 RS8 8m -Remote sensing TRV sensor

Figure number: D889 RT2 2m -Remote adjusting TRV transmitter

Figure number: D889 RT8 8m -Remote adjusting TRV transmitter

Sensors & Transmitters


Figure number: T70 15mm -Nut and olive 22mm -

Figure number: T95 - -90o Elbow - -

Figure number: T100 - -Tamper proof ring - -

Accessories

DRAIN COCKS



Figure number: D340 1/2" - 0.13PN10 Bronze Drain tap - Lockshield 3/4" - 0.35Threaded Male BS 21 Taper 1" - 0.59WRAS listed

Figure number: D341 1/2" - 0.12PN10 Bronze Drain tap 3/4" - 0.34Threaded Male BS 21 Taper 1" - 0.58WRAS listed

Figure number: D344 1/2" 114 0.45PN10 Bronze Draw off cock taper plug type 3/4" 136 0.70Gland sealed 1" 150 1.20Threaded Female BS 21 Taper 11/4" 170 2.01

11/2" 204 2.612" 240 4.14

Figure number: D344.1/2 1/2" 125 0.48PN10 Bronze Draw off cock taper plug type 3/4" 145 0.73Gland sealed 1" 165 1.23Threaded Male BS 21 Taper 11/4" 185 2.10

11/2" 220 2.752" 250 4.31

Figure number: D171MHUPN25 Bronze ball valve, Lever operated 1/2" 104 0.27Male x hose union outlet 3/4" 124 0.55WRAS listed 1" 147 0.88Male threaded ends to BSEN 10226 Taper

Figure number: D171MHULSPN25 Bronze ball valve, Lockshield operated 1/2" 104 0.31Male x hose union outlet 3/4" 124 0.58WRAS listed 1" 147 0.90Male threaded ends to BSEN 10226 Taper

Drain Cocks

THERMAL BALANCING VALVES



Figure number: D1880 15mm 0.70PN16 Bronze MultiTherm valve 20mm 0.90for circuits greater than 10m length 25mm 1.20

Figure number: D1882 - -Universal drain valve - -

Figure number: D1883 - -Universal thermometer - -

Figure number: D1884 - -Universal insulation shell - -

Figure number: D1885 - -Universal thermal sensor - -

Figure number: D1886 15mm -Optional mapress ends 20mm -

25mm -

Figure number: D1887 15mm -Optional mepla ends 20mm -

25mm -

Figure number: D1888 1/2" -Optional male bsp 3/4" -

1" -

Figure number: D1889 - -Copper tails - -

MultiTherm Automatic Circulation Regulating Valve


Figure Number: D1890 15mm 0.40PN16 Bronze valvefor circuits less than 10m length

EtaTherm Automatic Circulation Regulating Valve

THERMAL BALANCING VALVES



Figure Number: D1088 1/2" 0.50PN16 steelvalve with integral filters and 3/4" 0.60check valves

Figure Number: D1089 1/2" 0.65PN16 steel valve with additional 3/4" 0.75isolation ball valves and MX tail pieces

Thermostatic Mixing Valves


Figure Number: D1892 15mm 0.30PN16 provides system temperature validation 20mm 0.40

25mm 0.50

MultiTee Temperature Monitoring Pocket& Thermometer

To streamline this selection process we have developedsoftware that allows all variables to be considered andbest valve options selected. The selection programme isused by Crane Sales/Technical staff to input customer

information throughout the designprocess and ensure that theoptimum design is achieved.

The outputs from the selectionsoftware are used by Consultants,Contractors, CommissioningEngineers, and our own Productionteam, ensuring consistencythroughout the whole process.

COMMPAC


CommPac ManifoldCommissioning System

CommPac Selection Programme

On large projects, significant time andcost can be eliminated by enablingcommissioning at convenient locations.Ends of corridors, or accessible cupboardscan be used, which would also eliminatedisruption to occupiers duringmaintenance works.

The CommPac is an exceptionally efficient, practical and versatile system:-

Dimensions & Weights

Maximum pressure 16 bar. Temperature rating -10 to 100ºC

• Up to six terminals can be served from a singleCommPac unit.

• All units are custom built to suit site specification.

• All site connections can be made without the need toaccess the internal components.

• CommPac is suitable for variable flow or constant flowsystems.

• All connections are BSPT Female, enabling standard pipeor specialist adapters to be used.

• Fan coil units can be flushed, vented and balancedwithout the time-consuming ‘looping out’ procedure.This can be carried out by one commissioningengineer instead of a team.

• A single strainer serves all circuits, eliminating theneed for individual strainers.

• All systems can be flushed through the uniqueDominator ‘H’ body.

• The single DPCV maintains constant differentialpressure between manifolds.

CommPac modules are built to suit individual project designrequirements. Correct selection of balancing valves anddifferential pressure control valves is essential to ensurecomfort control andsystem efficiency. Flowrates, Pipe sizes, Pipematerials, and Pipelosses all have to becalculated to ensurethat each CommPacmodule contains thecorrect combination ofproducts to achievethe best results.

OUTLETS LENGH HEIGHT WIDTH WEIGHT& INLETS (mm) (mm) (mm) (kg)

6x6 1120 250 290 40

5x5 1120 250 290 38

4x4 880 250 290 36

3x3 880 250 290 34

2x2 640 250 290 30

Material Specifications

PART MATERIAL

H - Body Bronze (Z3000)

Strainer Bronze (D297)

Manifolds Bronze

Isolation Valves DZR Brass (D171A)

Regulation Valves Bronze (D931 or D981)

Benefits for Design Engineers

• minimal design involvement• all the necessary components supplied as one testedunit

• no risk of a component being omitted from a system atinstallation

• known performance of the entire unit• saves time, reduces specification risks and providesmaximum value to the client


Dimensions & Weights

ITEM DESCRIPTION MATERIAL

1 Bypass Valve Bronze to BSEN 1982CC491K

2 ProBalance valve (D931) Refer to ProBalance literature

3 D297 strainer Bronze to BSEN 1982CC491K

4 Union Brass to BSEN 12165CW617N

5 P84 test point DZR to BSEN 12164CW602N

6 Drain cock DZR to BSEN 12164 CW602N

Dominator Z3000Flow Management System for Fan Coil Units

Specification

The unique bypass valve unit comprises two T-ported ballvalves allowing easy back flushing, forward flushing andisolation. The position of the T-handle gives clearindication of flow/bypass mode. Designed around 3/4”full bore ball for optimum flow, can be adapted to 1/2”,3/4” and 1” end connections. Simple attachment toexisting hangers. The strainer unit has an integral draincock and pressure test point enabling measurement ofpressure drop across load and allowing for flushing ofstrainer and coil without need to remove basket.

Application

The Z3000 is a prefabricated unit combining the essentialcontrol components and connecting pipework associatedwith fan coils, into one compact, fully assembled unitready for simple and fast on-site connection.

The Dominator is compact and lightweight

• The complete unit is factory tested• Integrated union joints allow for custom alignment• 80mm supply/return centres allow for ease of lagging• Ease of installation

The unique bypass valve unit comprising twoT-ported ball valves

• Allows easy back flushing, forward flushing and isolation• The position of the T-handle gives clear indication offlow/bypass mode

• Designed around 3/4” full bore ball for optimum flow• Can be adapted to 1/2”, 3/4” and 1” end connections• Simple attachment to existing hangers

The strainer unit has an integral drain cockand pressure test point

• Enabling measurement of pressure drop across load• Allowing for flushing of strainer and coil without needto remove basket

Benefits for Installing Contractors

• significant reduction in site labour and nstallation costs• fast connection of one complete assembly• standardised components with guaranteed testedperformance

• less purchase orders, minimal administration• simple on-site connection

Threaded BSEN10226 formerly BS21 (ISO 7) for Two Unit System

Pressure/temperature ratings

Maximum temperature 120ºc

TEMPERATURE ºC -10 TO 100 110 120

PRESSURE (BAR) 16.0 160.0 16.0

DOMINATOR Z3000

DOMINATOR Z3000


The Dominator range comprises two series:

• Z3000 series features the Crane ProBalance FixedOrifice Double Regulating valve D931.

• Z3900 series features the Crane MotoBalance FixedOrifice Double Regulating valve D981P, suitable foruse with actuator.

Both series provide versions for heated and chilled watersystems and combinations with and without drains andstrainers.The versions for chilled water systems includeextension stems (EXS) on the ball valve T-handles toallow for lagging. The Z3000 series also includes low flowand ultra low flow versions.

Z3000 Series comprises the three variants as shown below.

This series utilises the Crane ProBalance Valves D931, D933 or D934 depending on flow rate required.

All selections are made by Crane and each unit is tagged with individual fan coil ref nos to assist contractors with siteassembly. Extension stems are fitted to isolation ball valves for chilled water services.

Z3900 Series comprises the three variants as shown below.

This series utilises the Crane MotoBalance Valves D981P, D983P or D984P depending on flow rate required.

The MotoBalance offers on/off or modulating control with equal percentage characteristics.

All selections are made by Crane and each unit is tagged with individual fan coil ref nos to assist contractors with siteassembly. Extension stems are fitted to isolation ball valves for chilled water services.

Z3000 with ProBalanceincludes drain and strainer

Z3010 with ProBalancewithout drain and strainer

Z3020 with ProBalanceincluding drain but without strainer

Z3000 with MotoBalanceincludes drain and strainer

Z3910 with MotoBalancewithout drain and strainer

Z3920 with MotoBalanceincluding drain but without strainer


D10 13

D104 15

D1088 32

D1089 32

D116 15

D138 15

D14 12

D140 15

D142 15

D15 12

D151 6

D151A 6

D151X 7

D155C 6

D156 8

D159 7

D16 12

D160 8

D161 8

D162 8

D166 7

D171 19

D171A 18

D171AC 18

D171C 19

D171MHU 19/30

D171MHULS 19/30

D180 7

D1880 31

D1882 31

D1883 31

D1884 31

D1885 31

D1886 31

D1887 31

D1888 31

D1889 31

D1890 31

D1892 32

D185AT 7

D191 18

D201 27

D202 27

D203 27

D235 7

D237 6

D237A 6

D255C 6

D295 26

D297 26

D298 26

D340 30

D341 30

D344 30

D344.1/2 30

D4 12

D46 12

D52 12

D7 12

D71 13

D72 13

D885 28

D886 28

D887 29

D888 29

D889 29

D901 23

D902 23

D921 23

D923 23

D931 24

D933 24

D934 24

D981P 24

D983P 24

D984P 24

DA931 24

DA941 24

DM11 13

DM160 8

DM161 8

DM6 13

DM900 23

DM921 23

DM925G 23

DM975G 23

DM931 25

DM941 24

DM950G 24

DM960 24

F174 10

F179 10

F182 10

F183 11

F201 15

F254 14

F273 27

F277 26

F372 14

F491 17

F493 17

F52 9

F53 9

F54 9

F58 10

F59 10

F611 20

F612 20

F614 20

F615 20

F621 21

F622 21

F624 21

F625 21

F626 22

F627 22

F628 22

F629 22

F84 10

FM124 9

FM125 9

FM276 26

FM278 27

FM369 14

FM450 16

FM451 16

FM453 16

FM455 16

FM469 16

FM492 16

FM52 9

FM57 9

FM63 9

FM82 10

P82 25

P83 25

P84 25

T70 29

T80 28

T90 28

T95 29

T100 25

47XU-F 11

33XU-F 11

76XU-F 11

143XU 14

151XU 14

171XU 14

147XU 17

159XU 17

175XU 17

Dominator 34

CommPac 33

Index of Figure Numbers

FIG NO. PAGE FIG NO. PAGE FIG NO. PAGEFIG NO. PAGE

37CRANE FLUID SYSTEMS TOTAL PRODUCT CATALOGUE

Pipe Fittings Summary

Hexagon Bush Hexagon Nipple Hexagon NippleReducing

Beaded Plug Solid Plain Plug Hollow

140* 144* 145* 146 147

Plain Plug Solid Countersunk Plug Backnut ParallelThread to BS 2779

Elbow M & F Elbow

148* 149* 150* 151* 152*

45˚ Elbow 45˚ M & F Elbow Tee M & F Tee Cross

155 156 161* 163 171*

Socket ParallelThread to BS 2779

Socket Taper Thread Socket Reducing Eccentric Socket Cap

176* 177 179* 180 185*

Male Bend M & F Bend Bend Twin Elbow Pitcher Tee

191 192 193 197 199

Return Bend Round Flange Union Flat Seat Union Spherical SeatIron to Iron

M & F Union SphericalSeat Iron to Iron

213 233 241 256* 257

Elbow Union SphericalSeat Iron to Iron

M & F Elbow UnionSpherical SeatIron to Iron

Union Spherical SeatBronze to Iron

M & F Union SphericalSeat Bronze to Iron

Elbow Union SphericalSeat Bronze to Iron

261 262 271 272 276

M & F Elbow UnionSpherical SeatBronze to Iron

Union Spherical SeatBronze to Bronze

Union Self Aligning(SA)

*Available in Bronze

277 289 290

CRANE HOUSE, EPSILON TERRACEWEST ROAD, IPSWICHSUFFOLK IP3 9FJ

TELEPHONE: +44 (0)1473 277300FAX: +44 (0)1473 277301EMAIL: [email protected]

www.cranefs.com CFS_TPC_06_2009

The Company reserve the right to amend any product without notice.

FM311ISO 9001

www.cranebsu.com

Documents

total valve