To whom it may concern.

In the past, gauges sold by TE connectivity for checking of the associated hand tools have been specified and sourced in various countries. The manufacture of gauges is often controlled by country specific standards and therefore the actual tolerances of the gauges reflects the appropriate standard of the source country. In certain instances, the country specific standard may mean that the actual gauge dimensions vary slightly from those specified in the relevant instruction sheets. In general, such gauges tend to have smaller tolerances than the instruction sheets require.

In order to avoid any possible confusion that may result from this slight variance, TE connectivity has now adopted new standardized gauge part numbers. These new part numbers avoid this country specific variability and provide dimensional conformance with the instruction sheets. These new gauge part numbers supersede and replace all previous part numbers.

TE connectivity has no reason to believe that use of the existing gauges will cause any lack of functionality or performance of the terminals applied by our tools.

A cross reference list of all new gauges is attached.

Data Sheet

Revised 5/18/2017 Page 1 of 29

Gauge to Hand Tool cross reference Data Sheet

45175 Pneumatic Head 69010525441-2 Wire Plug Gauge 16-14 AWG Crimp Chamber

45062-3 Hand Tool - TERMASHIELD Ferrule525440-2 Insulation Plug Gauge Primary Conductor insulation range .033-.059

45063-3 Hand Tool - TERMASHIELD Ferrule1-525443-7 Insulation Plug Gauge Ins Range .059-.085

45064-3 Hand Tool - TERMASHIELD Ferrule1-525443-3 Insulation Plug Gauge Ins Range .085-.095

45065-3 Hand Tool - TERMASHIELD Ferrule1-525443-6 Insulation Plug Gauge Ins Range .095-.115

45066-3 Hand Tool - TERMASHIELD Ferrule1-525440-0 Wire Plug Gauge (BNC) Braid Crimp

45098 CERTI-CRIMP SAHT525440-9 Insulation Plug Gauge 22-14 AWG

45099 Straight Action Double Action Hand Tool525447-7 Wire Plug Gauge 24-20 AWG (RED)

45158-2 Hand Tool - TERMASHIELD Ferrule1-525443-4 Insulation Plug Gauge Ins Range .245-.270

45216 Double Action Hand Tool1-525442-7 Wire Plug Gauge 22-14 AWG

45219-2 Double Action Hand Tool5-525442-6 Plug Gauge 22-10

45238-2 Die-set - TERMASHIELD Ferrule Tool1-525443-2 Insulation Plug Gauge Ins Range .130-.145

45239-2 Hand Tool - TERMASHIELD Ferrule1-525440-1 Insulation Plug Gauge Ins Range .145-.184 (White)

Revised 5/18/2017 Page 2 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

45240-2 Hand Tool - TERMASHIELD Ferrule1-525443-5 Insulation Plug Gauge Ins Range .184-.220

45241-2 Hand Tool - TERMASHIELD Ferrule1-525443-8 Insulation Plug Gauge Ins Range .220-.245

45433 Die-set - Hydraulic Head Open (Shank Die)1-525441-3 Wire Plug Gauge 2 AWG

45436 Die-set - Hydraulic Head Open (Shank Die)1-525441-4 Wire Plug Gauge 1/0 AWG

45439 Die-set - Hydraulic Head Open (Shank Die)2-525441-1 Wire Plug Gauge 2/0 AWG

45442 Die-set - Hydraulic Head Open (Shank Die)525441-7 Wire Plug Gauge 3/0 AWG

45445 Die-set - Hydraulic Head Open (Shank Die)4-525441-4 Wire Plug Gauge 4/0 AWG (RED)

45575-1 Double Action Hand Tool525442-8 Wire Plug Gauge 16-14 AWG Crimp Chamber

525449-9 Insulation Plug Gauge 16-14 AWG

45730 Straight Action Double Action Hand Tool4-525441-7 Wire Plug Gauge 26-24 AWG

525440-1 Insulation Plug Gauge 26-24 AWG

46073 Straight Action Double Action Hand Tool1-525442-2 Wire Plug Gauge 24-20 AWG

1-525442-3 Insulation Plug Gauge 24-20 AWG

46121 Double Action Hand Tool2-525442-0 Wire Plug Gauge 26-22 AWG

525446-8 Insulation Slip Gauge AWG 22-16

Revised 5/18/2017 Page 3 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

46145 Die-Indenter - Shank Die 690971-525441-5 Wire Plug Gauge 8 AWG

46146 Die-Nest - Shank Die 690971-525441-5 Wire Plug Gauge 8 AWG

46222 Double Action Hand Tool2-525442-0 Wire Plug Gauge 26-22 AWG

46256 Double Action Hand Tool525446-6 Insulation Slip Gauge 22 AWG

46282 Pneumatic Head 69010525442-7 Wire Plug Gauge 22-16 AWG

525446-6 Insulation Slip Gauge 22 AWG

46284 Pneumatic Head 69010525442-8 Wire Plug Gauge 16-14 AWG Crimp Chamber

46447 Double Action Hand Tool525441-1 Wire Plug Gauge 12-10 AWG Crimp Chamber

525441-2 Wire Plug Gauge 16-14 AWG Crimp Chamber

525441-3 Wire Plug Gauge 22-16 AWG Crimp Chamber

46467 Straight Action Double Action Hand Tool1-525441-1 Wire Plug Gauge 22-20 AWG

525440-3 Insulation Plug Gauge 22-20 AWG

46468 Straight Action Double Action Hand Tool1-525440-2 Insulation Plug Gauge 22-20 / 18-16 AWG

525441-3 Wire Plug Gauge 22-16 AWG Crimp Chamber

46469 Straight Action Double Action Hand Tool1-525440-3 Insulation Plug Gauge 14 AWG

2-525441-4 Wire Plug Gauge 14 AWG

Revised 5/18/2017 Page 4 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

46470 Straight Action Double Action Hand Tool1-525440-4 Insulation Plug Gauge 12-10 AWG

2-525441-6 Wire Plug Gauge 12-10 AWG Crimp Chamber

46673 Double Action Hand Tool525441-2 Wire Plug Gauge 16-14 AWG Crimp Chamber

525446-8 Insulation Slip Gauge AWG 22-16

46673-1 Double Action Hand Tool525441-2 Wire Plug Gauge 16-14 AWG Crimp Chamber

525446-8 Insulation Slip Gauge AWG 22-16

46988 Double Action Hand Tool1-525446-4 Insulation Plug Gauge 16-14 AWG Crimp Chamber

2-525441-5 Wire Plug Gauge 16-14 AWG

47236-1 Die-set - Hydraulic Head Closed (Shank Die)2-525442-9 Wire Plug Gauge 8 AWG (Red)

47304 Double Action Hand Tool2-525442-0 Wire Plug Gauge 26-22 AWG

525446-8 Insulation Slip Gauge AWG 22-16

47386 Double Action Hand Tool525442-7 Wire Plug Gauge 22-16 AWG

525446-8 Insulation Slip Gauge AWG 22-16

47386-4 Double Action Hand Tool525442-7 Wire Plug Gauge 22-16 AWG

525446-8 Insulation Slip Gauge AWG 22-16

47386-5 Double Action Hand Tool525442-7 Wire Plug Gauge 22-16 AWG

525446-8 Insulation Slip Gauge AWG 22-16

Revised 5/18/2017 Page 5 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

47387 Double Action Hand Tool525442-8 Wire Plug Gauge 16-14 AWG Crimp Chamber

525446-7 Insulation Slip Gauge 14 AWG

47387-7 Double Action Hand Tool525442-8 Wire Plug Gauge 16-14 AWG Crimp Chamber

525446-7 Insulation Slip Gauge 14 AWG

47516 Pneumatic Head 69005525442-7 Wire Plug Gauge 22-16 AWG

47518 Pneumatic Head 69010525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

47807-1 Die-set - C-Head SAHT525446-7 Insulation Slip Gauge 14 AWG

47808 Die-set - C-Head SAHT - HD525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

47808-5 Die-set - C-Head SAHT - HD525446-9 Insulation Slip Gauge 12-10 AWG

47808-6 Die-set - C-Head SAHT - HD525446-9 Insulation Slip Gauge 12-10 AWG

47820 Die-set - Hydraulic Hand tool 59974-12-525442-9 Wire Plug Gauge 8 AWG (Red)

47821 Die-set - Hydraulic Hand tool 59974-13-525442-3 Wire Plug Gauge 6-8 AWG

47822 Die-set - Hydraulic Hand tool 59974-13-525442-4 Wire Plug Gauge 4-8 AWG

47823 Die-set - hydraulic Hand tool 59974-13-525442-7 Wire Plug Gauge 2 AWG (RED)

Revised 5/18/2017 Page 6 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

47824 Die-set - Hydraulic Head Closed (Shank Die)525447-1 Wire Plug Gauge

47825 Die-set - Hydraulic Head Closed (Shank Die)525447-2 Wire Plug Gauge 2/0 AWG (YELLOW)

47907-1 Double Action Hand Tool1-525442-9 Wire Plug Gauge 24-20 AWG

525446-6 Insulation Slip Gauge 22 AWG

47915 Die-set - Hydraulic Head Closed (Shank Die)525447-3 Wire Plug Gauge 3/0 AWG (RED)

47918 Die-set - Hydraulic Head Closed (Shank Die)525447-4 Wire Plug Gauge 4/0 AWG (RED)

48087 Double Action Hand Tool3-525442-1 Wire Plug Gauge 22-14 AWG (PURPLE)

48127 Die-Indenter - Shank Die3-525441-0 Wire Plug Gauge 4 AWG

3-525441-2 Wire Plug Gauge 6 AWG

3-525441-3 Wire Plug Gauge 2 AWG

48127-1 Die-Indenter - Shank Die3-525441-0 Wire Plug Gauge 4 AWG

3-525441-2 Wire Plug Gauge 6 AWG

3-525441-3 Wire Plug Gauge 2 AWG

48128 Die-Nest - Shank Die3-525441-2 Wire Plug Gauge 6 AWG

48128-1 Die-Nest - Shank Die3-525441-2 Wire Plug Gauge 6 AWG

48129 Die-Nest - Shank Die3-525441-0 Wire Plug Gauge 4 AWG

Revised 5/18/2017 Page 7 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

48129-1 Die-Nest - Shank Die3-525441-0 Wire Plug Gauge 4 AWG

48130 Die-Nest - Shank Die3-525441-3 Wire Plug Gauge 2 AWG

48130-1 Die-Nest - Shank Die3-525441-3 Wire Plug Gauge 2 AWG

48131 Die-Indenter - Shank Die3-525441-1 Wire Plug Gauge 1/0 AWG

48131-1 Die-Indenter - Shank Die3-525441-1 Wire Plug Gauge 1/0 AWG

48132 Die-Nest - Shank Die3-525441-1 Wire Plug Gauge 1/0 AWG

48132-1 Die-Nest - Shank Die3-525441-1 Wire Plug Gauge 1/0 AWG

48172 Pneumatic Head 690155-525441-0 Wire Plug Gauge 6 W

48173 Pneumatic Head 690155-525441-1 Wire Plug Gauge 4 W

48174 Pneumatic Head 690152-525441-7 Wire Plug Gauge

48183 Pneumatic Head 690155-525441-2 Wire Plug Gauge 1/0 W

48412 Pneumatic Head 690151-525441-5 Wire Plug Gauge 8 AWG

48507 Die-Indenter - Shank Die 690672-525441-0 Wire Plug Gauge 3/0 AWG

5-525441-5 Wire Plug Gauge 4 W

48509 Die-Nest - Shank Die 690675-525441-5 Wire Plug Gauge 4 W

Revised 5/18/2017 Page 8 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

48510 Die-Nest - Shank Die 690672-525441-0 Wire Plug Gauge 3/0 AWG

48518-2 Double Action Hand Tool2-525442-0 Wire Plug Gauge 26-22 AWG

525446-8 Insulation Slip Gauge AWG 22-16

48752-1 Die-set - Hydraulic Hand tool 59974-11-525449-0 Insulation Plug Gauge 8 AWG

2-525442-9 Wire Plug Gauge 8 AWG (Red)

48753-1 Die-set - Hydraulic Hand tool 59974-13-525442-0 Wire Plug Gauge 6 AWG (BLUE)

525449-1 Insulation Plug Gauge 6 AWG

48754-1 Die-set - Hydraulic Hand tool 59974-13-525442-6 Wire Plug Gauge

525449-2 Insulation Plug Gauge

48755-1 Die-set - Hydraulic Hand tool 59974-13-525442-7 Wire Plug Gauge 2 AWG (RED)

525449-3 Insulation Plug Gauge 2 AWG

48756-1 Die-set - Hydraulic Head Closed (Shank Die)523763-4 Wire Plug Gauge 1/0 AWG

48757-1 Die-set - Hydraulic Head Closed (Shank Die)523763-7 Wire Plug Gauge AWG 2/0

48759-1 Die-set - Hydraulic Head Closed (Shank Die)525447-4 Wire Plug Gauge 4/0 AWG (RED)

48858-1 Die-set - Hydraulic Head Closed (Shank Die)2-525442-9 Wire Plug Gauge 8 AWG (Red)

48859-1 Die-set - Hydraulic Head Closed (Shank Die)3-525442-0 Wire Plug Gauge 6 AWG (BLUE)

Revised 5/18/2017 Page 9 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

48860-1 Die-set - Hydraulic Head Closed (Shank Die)3-525442-4 Wire Plug Gauge 4-8 AWG

525449-8 Insulation Plug Gauge 4 AWG

48861-1 Die-set - Hydraulic Head Closed (Shank Die)3-525442-7 Wire Plug Gauge 2 AWG (RED)

525449-7 Insulation Plug Gauge 2 AWG

49935 Double Action Hand Tool525441-4 Wire Plug Gauge 22-16 AWG Crimp Chamber

525441-5 Wire Plug Gauge 16-14 AWG Crimp Chamber

525441-6 Wire Plug Gauge 12-10 AWG Crimp Chamber

49956 Pneumatic Head 690151-525441-5 Wire Plug Gauge 8 AWG

49975 Double Action Hand Tool2-525441-9 Wire Plug Gauge 16-14 AWG

58079-3 Tetra-Crimp Hand Tool4-525442-3 Plug Gauge 22-20 AWG

4-525442-4 Plug Gauge 18 AWG

58080-3 Tetra-Crimp Hand Tool4-525442-7 Plug Gauge 16 AWG

4-525442-8 Plug Gauge 14 AWG

58212-1 Die-set - C-Head SAHT525444-1 Plug Gauge Ferrule (Braid Crimp)

525444-2 Plug Gauge Centre Contact (Braid Crimp)

58305-1 T-Head Hand Tool525447-7 Wire Plug Gauge 24-20 AWG (RED)

58545-1 Die-set - SDE (shoulder)4-525441-9 Wire Plug Gauge 22-16 AWG

Revised 5/18/2017 Page 10 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

58545-3 Die-set - SDE Electric Terminator4-525441-9 Wire Plug Gauge 22-16 AWG

58545-4 Die-set - SDE 626 Adaptor4-525441-9 Wire Plug Gauge 22-16 AWG

59118 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

59170 T-Head Hand Tool2-525446-1 Insulation Slip Gauge 22-16 AWG

2-525446-2 Insulation Slip Gauge 16-14 AWG

525442-7 Wire Plug Gauge 22-16 AWG

59239-4 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

525446-9 Insulation Slip Gauge 12-10 AWG

59239-8 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

525446-9 Insulation Slip Gauge 12-10 AWG

59250 T-Head Hand Tool2-525446-1 Insulation Slip Gauge 22-16 AWG

2-525446-2 Insulation Slip Gauge 16-14 AWG

525442-7 Wire Plug Gauge 22-16 AWG

525442-8 Wire Plug Gauge 16-14 AWG Crimp Chamber

59275 T-Head Hand Tool1-525442-9 Wire Plug Gauge 24-20 AWG

2-525442-0 Wire Plug Gauge 26-22 AWG

2-525446-3 Insulation Plug Gauge 26-22 / 24-20 AWG

Revised 5/18/2017 Page 11 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

59282 CERTI-SEAL Hand Tool4-525442-2 Wire Plug Gauge AWG 16-14

5-525442-3 Insulation Plug Gauge 16-14 AWG

59287 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

59287-2 Heavy Head Hand Tool525446-9 Insulation Slip Gauge 12-10 AWG

59294 Heavy Head Hand Tool2-525441-5 Wire Plug Gauge 16-14 AWG

59300 T-Head Hand Tool1-525442-9 Wire Plug Gauge 24-20 AWG

59461 Heavy Head Hand Tool1-525446-5 Insulation Plug Gauge 12-10 AWG

2-525441-8 Wire Plug Gauge 12-10 AWG

59489 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

59824-1 Tetra-Crimp Hand Tool525449-4 Insulation Plug Gauge 22-16 AWG

525449-5 Insulation Plug Gauge 16-14 AWG

525449-6 Insulation Plug Gauge 12-10 AWG

59877-1 Die-set - Hydraulic Head Closed (Shank Die)2-525443-5 Insulation Plug Gauge 3/0

5-525441-3 Wire Plug Gauge 2/0 W

Revised 5/18/2017 Page 12 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

59975-1 Hydraulic Hand Tool - SOLISTRAND1-525441-6 Wire Plug Gauge 4 AWG

1-525441-7 Wire Plug Gauge 2 AWG

1-525441-8 Wire Plug Gauge 6 AWG

1-525441-9 Wire Plug Gauge 8 AWG

59993-1 Die-set - C-Head SAHT - HD1-525442-8 Wire Plug Gauge Centre Contact

525443-5 Plug Gauge Ferrule

68006 Die-set - Hydraulic Head Closed (Shank Die)1-525448-7 Insulation Plug Gauge 8/10

5-525441-4 Wire Plug Gauge 8 W

68007 Die-set - Hydraulic Head Closed (Shank Die)1-525443-0 Insulation Plug Gauge 8/6 AWG

2-525441-3 Wire Plug Gauge 8/6 AWG

68008 Die-set - Hydraulic Head Closed (Shank Die)525441-8 Wire Plug Gauge 4 AWG

525443-8 Insulation Plug Gauge 6/4 AWG

68009 Die-set - Hydraulic Head Closed (Shank Die)525441-9 Wire Plug Gauge 2 AWG

525443-6 Insulation Plug Gauge

68010 Die-set - Hydraulic Head Closed (Shank Die)1-525441-0 Wire Plug Gauge 1/0 AWG

525443-7 Insulation Plug Gauge

68010-1 Die-set - Hydraulic Head Closed (Shank Die)1-525441-0 Wire Plug Gauge 1/0 AWG

525443-7 Insulation Plug Gauge

68011-1 Die-set - Hydraulic Head Closed (Shank Die)2-525441-2 Wire Plug Gauge 2/1 AWG

525443-9 Insulation Plug Gauge 2/1 AWG

Revised 5/18/2017 Page 13 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

68049 Die-set - Hydraulic Head Open (Shank Die)3-525442-8 Wire Plug Gauge 3/0 AWG

525447-8 Wire Plug Gauge 3/0 AWG

68050 Die-set - Hydraulic Head Open (Shank Die H'Duty)4-525442-0 Wire Plug Gauge 4/0 AWG

525447-9 Wire Plug Gauge 4/0 AWG

69140-1 Straight Action Double Action Hand Tool1-525443-9 Insulation Plug Gauge (BNC) Braid Crimp

69140-2 Straight Action Double Action Hand Tool2-525443-0 Insulation Plug Gauge (BNC) Braid Crimp

69150-1 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

69151-1 Double Action Hand Tool525446-8 Insulation Slip Gauge AWG 22-16

69211-1 Die-set - Hydraulic Head Open (Shank Die)2-525442-8 Wire Plug Gauge

69212-1 Die-set - Hydraulic Head Open (Shank Die)1-525447-2 Wire Plug Gauge

69213-1 Die-set - Hydraulic Head Open (Shank Die)1-525447-3 Wire Plug Gauge

69214-1 Die-set - Hydraulic Head Open (Shank Die)1-525447-4 Wire Plug Gauge

69215-1 Die-set - Hydraulic Head Open (Shank Die)1-525447-5 Wire Plug Gauge

69216 Die-set - Hydraulic Head Open (Shank Die)1-525441-5 Wire Plug Gauge 8 AWG

69217 Die-set - Hydraulic Head Open (Shank Die)1-525441-2 Wire Plug Gauge 6 AWG

Revised 5/18/2017 Page 14 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

69218 Die-set - Hydraulic Head Open (Shank Die)3-525441-4 Wire Plug Gauge 4 AWG

69254-1 Die-set - Hydraulic Head Open (Shank Die)1-525447-6 Wire Plug Gauge

69260-1 CERTI-CRIMP SAHT525440-8 Insulation Plug Gauge Die Colour Code; Green

69272-1 CERTI-CRIMP SAHT525440-8 Insulation Plug Gauge Die Colour Code; Green

525448-6 Wire Plug Gauge Die Colour Code Orange

525448-7 Wire Plug Gauge Die Colour Code White

69322-1 Heavy Head Hand Tool1-525447-0 Plug Gauge

69339 Heavy Head Hand Tool4-525441-8 Wire Plug Gauge 8 AWG

69342 Die-set - C-Head SAHT1-525442-9 Wire Plug Gauge 24-20 AWG

69344 Die-set - C-Head SAHT2-525442-0 Wire Plug Gauge 26-22 AWG

69352 Heavy Head Hand Tool1-525447-1 Plug Gauge 22-18 AWG

2-525443-3 Wire Plug Gauge 22-18 AWG

69354-1 Heavy Head Hand Tool1-525441-5 Wire Plug Gauge 8 AWG

69355 Heavy Head Hand Tool1-525441-5 Wire Plug Gauge 8 AWG

69363 Double Action Hand Tool1-525441-1 Wire Plug Gauge 22-20 AWG

4-525441-5 Plug Gauge - Wire

Revised 5/18/2017 Page 15 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

69376-1 Straight Action Double Action Hand Tool525440-7 Insulation Plug Gauge Centre Contact

69454 Double Action Hand Tool525446-8 Insulation Slip Gauge AWG 22-16

69477-1 Double Action Hand Tool525448-1 Plug Gauge Ferrule Crimping Chamber (BNC)

69493 Die-set - C-Head SAHT525440-7 Insulation Plug Gauge Centre Contact

69656-1 Straight Action Double Action Hand Tool525447-6 Wire Plug Gauge Core Wire Crimp (COAX)

69656-2 Straight Action Double Action Hand Tool525447-6 Wire Plug Gauge Core Wire Crimp (COAX)

69656-8 Straight Action Double Action Hand Tool525447-6 Wire Plug Gauge Core Wire Crimp (COAX)

69656-9 Straight Action Double Action Hand Tool525447-6 Wire Plug Gauge Core Wire Crimp (COAX)

69731 Die-set - C-Head SAHT2-525442-2 Wire Plug Gauge 26-24 AWG Crimp Chamber

69732 Die-set - C-Head SAHT2-525442-3 Wire Plug Gauge 22-20 AWG Crimp Chamber

69733 Die-set - C-Head SAHT2-525442-4 Wire Plug Gauge 18-16 AWG Crimp Chamber

69734 Die-set - C-Head SAHT2-525442-5 Wire Plug Gauge 14 AWG Crimp Chamber

525446-7 Insulation Slip Gauge 14 AWG

Revised 5/18/2017 Page 16 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

69735 Die-set - C-Head SAHT - HD2-525442-6 Wire Plug Gauge

525446-9 Insulation Slip Gauge 12-10 AWG

69763 Die-set - Hydraulic Hand tool 59974-1525447-5 Wire Plug Gauge (Colour code red)

90009-8 Double Action Hand Tool523763-1 Wire Plug Gauge

90015 Double Action Hand Tool2-525442-0 Wire Plug Gauge 26-22 AWG

2-525446-5 Insulation Plug Gauge 26 / 24-22 AWG

90016 Double Action Hand Tool3-525442-2 Wire Plug Gauge 20-16 AWG

90035-3 Double Action Hand Tool2-525442-1 Wire Plug Gauge 22-18 AWG

2-525446-4 Insulation Plug Gauge 22-18 AWG

90093 Straight Action Double Action Hand Tool525447-7 Wire Plug Gauge 24-20 AWG (RED)

90120 Double Action Hand Tool525445-3 Wire Plug Gauge 14-12 AWG Crimp Chamber

525445-4 Wire Plug Gauge 10 AWG Crimp Chamber

90246-1 Heavy Head Hand Tool3-525442-5 Wire Plug Gauge 14-12 AWG

90276-2 Heavy Head Hand Tool2-525442-7 Wire Plug Gauge 10 AWG Crimp Chamber

525446-9 Insulation Slip Gauge 12-10 AWG

90391-3 Tetra-Crimp Hand Tool4-525442-9 Plug Gauge 16-14 AWG

Revised 5/18/2017 Page 17 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

169404 Die-set - CERTI-LOK1-525442-0 Wire Plug Gauge 22-18 AWG Crimp Chamber

525442-8 Wire Plug Gauge 16-14 AWG Crimp Chamber

525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

169409 Die-set - CERTI-LOK525441-4 Wire Plug Gauge 22-16 AWG Crimp Chamber

525441-5 Wire Plug Gauge 16-14 AWG Crimp Chamber

525441-6 Wire Plug Gauge 12-10 AWG Crimp Chamber

169485 Double Action Hand Tool2-525442-0 Wire Plug Gauge 26-22 AWG

525446-8 Insulation Slip Gauge AWG 22-16

169490 Die-set - CERTI-LOK525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

220009-1 Double Action Hand Tool4-525442-5 Wire Plug Gauge, center contact

4-525442-6 Wire Plug Gauge, ferrule

220015-1 Heavy Head Hand Tool2-525443-1 Insulation Plug Gauge

523763-2 Insulation Plug Gauge

523763-3 Plug Gauge

525443-1 Braid Dies Plug Gauge

220015-2 Heavy Head Hand Tool2-525443-4 Braid Dies Plug Gauge

523763-2 Insulation Plug Gauge

523763-3 Plug Gauge

525443-2 Braid Dies Plug Gauge

220015-3 Heavy Head Hand Tool523763-2 Insulation Plug Gauge

523763-3 Plug Gauge

525443-3 Braid Dies Plug Gauge

Revised 5/18/2017 Page 18 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

220015-4 Heavy Head Hand Tool523763-2 Insulation Plug Gauge

523763-3 Plug Gauge

525443-1 Braid Dies Plug Gauge

220015-5 Heavy Head Hand Tool523763-2 Insulation Plug Gauge

523763-3 Plug Gauge

525443-4 Braid Dies Plug Gauge

220015-6 Heavy Head Hand Tool2-525443-4 Braid Dies Plug Gauge

523763-2 Insulation Plug Gauge

523763-3 Plug Gauge

525443-2 Braid Dies Plug Gauge

220045-2 Double Action Hand Tool525440-4 Insulation Plug Gauge Centre Contact

525440-5 Insulation Plug Gauge Braid Section

525440-6 Insulation Plug Gauge Braid Gap Section

220061-1 Double Action Hand Tool1-525448-0 Plug Gauge Braid Gap Crimp B

1-525448-1 Plug Gauge Braid Crimp A

1-525448-2 Plug Gauge Braid Gap Crimp A

525448-9 Plug Gauge Braid Crimp B

220062-1 Die-set - C-Head SAHT525440-4 Insulation Plug Gauge Centre Contact

525440-5 Insulation Plug Gauge Braid Section

525440-6 Insulation Plug Gauge Braid Gap Section

Revised 5/18/2017 Page 19 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

220066-1 Double Action Hand Tool525448-2 Plug Gauge "A" Crimping Chamber

525448-3 Plug Gauge "B" Crimping Chamber

525448-4 Plug Gauge "C" Crimping Chamber

220066-2 Double Action Hand Tool5-525442-0 Plug Gauge Center Contact Crimp

5-525442-1 Plug Gauge Center Contact Crimp

5-525442-2 Plug Gauge Center Contact Crimp

220141-1 Double Action Hand Tool1-525448-3 Insulation Plug Gauge Braid Crimp

1-525448-4 Insulation Plug Gauge Braid Crimp

523763-8 Plug Gauge Center Conductor Crimp

220141-2 Double Action Hand Tool1-525448-3 Insulation Plug Gauge Braid Crimp

1-525448-5 Insulation Plug Gauge Braid Crimp

523763-8 Plug Gauge Center Conductor Crimp

220189-3 Die-set - SDE (shoulder)2-525443-6 Insulation Plug Gauge FERRULE

5-525442-4 Plug Gauge CENTER

300583 Pneumatic Head 690102-525441-9 Wire Plug Gauge 16-14 AWG

314948-1 Die-set - Hydraulic Head Closed (Shank Die)4-525441-6 Wire Plug Gauge 3/0 W

523763-6 Insulation Plug Gauge 3/0 W

314964-1 Die-set - Hydraulic Head Closed (Shank Die)525443-9 Insulation Plug Gauge 2/1 AWG

5-525441-7 Wire Plug Gauge 1/0

Revised 5/18/2017 Page 20 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

476268 Double Action Hand Tool525442-7 Wire Plug Gauge 22-16 AWG

525446-8 Insulation Slip Gauge AWG 22-16

476407 Straight Action Double Action Hand Tool525440-7 Insulation Plug Gauge Centre Contact

476408 Straight Action Double Action Hand Tool525440-7 Insulation Plug Gauge Centre Contact

476409 Die-set - C-Head SAHT525440-7 Insulation Plug Gauge Centre Contact

476410 Die-set - C-Head SAHT525440-7 Insulation Plug Gauge Centre Contact

525448-5 Plug Gauge Insulation Crimp (BNC)

477321 Pneumatic Head 69010525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

477323-2 Double Action Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

482861-1 Double Action Hand Tool525442-7 Wire Plug Gauge 22-16 AWG

482930-1 Double Action Hand Tool2-525442-0 Wire Plug Gauge 26-22 AWG

483295-1 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

484364-1 Heavy Head Hand Tool525442-2 Wire Plug Gauge 18 AWG Crimp Chamber (2 Dots Orange)

Revised 5/18/2017 Page 21 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

525690 Double Action Hand Tool2-525446-6 Insulation Plug Gauge 20-18

525442-7 Wire Plug Gauge 22-16 AWG

525691 Double Action Hand Tool1-525446-6 Insulation Plug Gauge 16-14 AWG (Blue dot - code 2)

525442-8 Wire Plug Gauge 16-14 AWG Crimp Chamber

525692 Heavy Head Hand Tool525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

525446-9 Insulation Slip Gauge 12-10 AWG

525693 Double Action Hand Tool525441-4 Wire Plug Gauge 22-16 AWG Crimp Chamber

525441-5 Wire Plug Gauge 16-14 AWG Crimp Chamber

525441-6 Wire Plug Gauge 12-10 AWG Crimp Chamber

543424-1 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

543424-2 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

543424-3 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

543424-4 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

543424-5 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

543424-6 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

543424-7 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

Revised 5/18/2017 Page 22 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

543424-8 Die-set - Ferrule Crimping Tool1-525448-6 Insulation Plug Gauge Braid Crimp

574573 Double Action Hand Tool525441-4 Wire Plug Gauge 22-16 AWG Crimp Chamber

525441-5 Wire Plug Gauge 16-14 AWG Crimp Chamber

525441-6 Wire Plug Gauge 12-10 AWG Crimp Chamber

576711 Die-set - C-Head SAHT525442-1 Wire Plug Gauge

525446-1 Insulation Slip Gauge 24-22 AWG Crimp Chamber

576714 Die-set - C-Head SAHT525442-3 Wire Plug Gauge 16 AWG Crimp Chamber (1 Dot Orange)

525446-4 Insulation Slip Gauge 18-16 AWG Crimp Chamber

576715 Die-set - C-Head SAHT525442-2 Wire Plug Gauge 18 AWG Crimp Chamber (2 Dots Orange)

525446-4 Insulation Slip Gauge 18-16 AWG Crimp Chamber

576716 Die-set - C-Head SAHT - HD525442-4 Wire Plug Gauge 14 AWG

525446-3 Insulation Slip Gauge 14-12 AWG

576720 Die-set - C-Head SAHT525442-1 Wire Plug Gauge

525446-2 Insulation Slip Gauge 20 AWG Crimp Chamber

576723 Die-set - C-Head SAHT - HD525442-6 Wire Plug Gauge 10 AWG

525446-5 Insulation Slip Gauge 10 AWG

Revised 5/18/2017 Page 23 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

576742 Die-set - C-Head SAHT - HD525442-5 Wire Plug Gauge 12 AWG

525446-3 Insulation Slip Gauge 14-12 AWG

576778 Heavy Head Hand Tool525442-1 Wire Plug Gauge

525446-1 Insulation Slip Gauge 24-22 AWG Crimp Chamber

576779 Heavy Head Hand Tool525442-1 Wire Plug Gauge

525446-2 Insulation Slip Gauge 20 AWG Crimp Chamber

576780 Heavy Head Hand Tool525442-2 Wire Plug Gauge 18 AWG Crimp Chamber (2 Dots Orange)

525446-4 Insulation Slip Gauge 18-16 AWG Crimp Chamber

576781 Heavy Head Hand Tool525442-3 Wire Plug Gauge 16 AWG Crimp Chamber (1 Dot Orange)

525446-4 Insulation Slip Gauge 18-16 AWG Crimp Chamber

576782 Heavy Head Hand Tool525442-4 Wire Plug Gauge 14 AWG

525446-3 Insulation Slip Gauge 14-12 AWG

576783 Heavy Head Hand Tool525442-5 Wire Plug Gauge 12 AWG

525446-3 Insulation Slip Gauge 14-12 AWG

576784 Heavy Head Hand Tool525442-6 Wire Plug Gauge 10 AWG

525446-5 Insulation Slip Gauge 10 AWG

601967-1 AF8601968-1 Plug Gauge - DMC G125

Revised 5/18/2017 Page 24 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

679300-1 626 Pneumatic Crimping Head (Large Tool Holder)2-525446-7 Insulation Plug Gauge 12-10

525442-9 Wire Plug Gauge 12-10 AWG Crimp Chamber

734535-1 SAHT (Wezag)1-525442-4 Wire Plug Gauge 24-20 AWG

1-525446-0 Insulation Slip Gauge 24-22 AWG Crimp Chamber

1-525446-1 Insulation Slip Gauge 20 AWG Crimp Chamber

734536-1 SAHT (Wezag)1-525442-5 Wire Plug Gauge 18-16 AWG Crimp Chamber

1-525442-6 Wire Plug Gauge 14 AWG Crimp Chamber

1-525446-2 Insulation Slip Gauge 18-16 AWG Crimp Chamber

1-525446-3 Insulation Slip Gauge 14 AWG Crimp Chamber

825508-5 CRIMPAC CG341465 Plug Gauge - GO / NOGO

904395-1 626 Pneumatic Crimping Head (Large Tool Holder)2-525442-9 Wire Plug Gauge 8 AWG (Red)

1490406-1 'U' Die Assy (14 ton)3-525442-7 Wire Plug Gauge 2 AWG (RED)

1490413-1 'U' Die Nest3-525441-5 Wire Plug Gauge 8 AWG

1490413-2 'U' Die Nest3-525441-2 Wire Plug Gauge 6 AWG

1490413-3 'U' Die Nest3-525441-0 Wire Plug Gauge 4 AWG

1490413-4 'U' Die Nest3-525441-3 Wire Plug Gauge 2 AWG

Revised 5/18/2017 Page 25 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

1490413-5 'U' Die Nest3-525441-1 Wire Plug Gauge 1/0 AWG

1490413-6 'U' Die Nest4-525441-0 Wire Plug Gauge 2/0 AWG

1490413-7 'U' Die Nest4-525441-2 Wire Plug Gauge 3/0 AWG

1490413-8 'U' Die Nest4-525441-3 Wire Plug Gauge 4/0 AWG

1490413-9 'U' Die Nest3-525441-6 Wire Plug Gauge 8 AWG

1-1490413- 'U' Die Nest3-525441-7 Wire Plug Gauge 6 AWG (Heavy duty & 90˚ bend terminals)

1-1490413- 'U' Die Nest3-525441-8 Wire Plug Gauge 4 AWG (Heavy duty & 90˚ bend terminals)

1-1490413- 'U' Die Nest3-525441-9 Wire Plug Gauge 2 AWG

1-1490413- 'U' Die Nest4-525441-1 Wire Plug Gauge 1/0 AWG (Heavy duty & 90˚ bend terminals)

1-1490413- 'U' Die Nest3-525441-5 Wire Plug Gauge 8 AWG

1-1490413- 'U' Die Nest3-525441-2 Wire Plug Gauge 6 AWG

1-1490413- 'U' Die Nest3-525441-0 Wire Plug Gauge 4 AWG

1-1490413- 'U' Die Nest3-525441-3 Wire Plug Gauge 2 AWG

Revised 5/18/2017 Page 26 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

1-1490413- 'U' Die Nest3-525441-1 Wire Plug Gauge 1/0 AWG

1-1490413- 'U' Die Nest4-525441-0 Wire Plug Gauge 2/0 AWG

2-1490413- 'U' Die Nest4-525441-2 Wire Plug Gauge 3/0 AWG

2-1490413- 'U' Die Nest4-525441-3 Wire Plug Gauge 4/0 AWG

1490414-1 'U' Die Indenter3-525441-5 Wire Plug Gauge 8 AWG

1490414-2 'U' Die Indenter3-525441-0 Wire Plug Gauge 4 AWG

3-525441-2 Wire Plug Gauge 6 AWG

3-525441-3 Wire Plug Gauge 2 AWG

3-525441-6 Wire Plug Gauge 8 AWG

3-525441-7 Wire Plug Gauge 6 AWG (Heavy duty & 90˚ bend terminals)

3-525441-8 Wire Plug Gauge 4 AWG (Heavy duty & 90˚ bend terminals)

1490414-3 'U' Die Indenter3-525441-1 Wire Plug Gauge 1/0 AWG

3-525441-9 Wire Plug Gauge 2 AWG

4-525441-0 Wire Plug Gauge 2/0 AWG

4-525441-1 Wire Plug Gauge 1/0 AWG (Heavy duty & 90˚ bend terminals)

4-525441-2 Wire Plug Gauge 3/0 AWG

4-525441-3 Wire Plug Gauge 4/0 AWG

Revised 5/18/2017 Page 27 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

1490597-1 'U' Die Assy2-525442-9 Wire Plug Gauge 8 AWG (Red)

1490598-1 'U' Die Assy3-525442-0 Wire Plug Gauge 6 AWG (BLUE)

1490599-1 'U' Die Assy3-525442-4 Wire Plug Gauge 4-8 AWG

1490700-1 'U' Die Assy (14 ton)525447-1 Wire Plug Gauge

1901000-1 Dies for Battery Tool Kit - 4 Ton Latch Head3-525441-2 Wire Plug Gauge 6 AWG

1901000-2 Dies for Battery Tool Kit - 4 Ton Latch Head3-525441-0 Wire Plug Gauge 4 AWG

1901000-3 Dies for Battery Tool Kit - 4 Ton Latch Head3-525441-3 Wire Plug Gauge 2 AWG

1901001-1 Dies for Battery Tool Kit - 4 Ton Latch Head3-525441-5 Wire Plug Gauge 8 AWG

1901002-1 Dies for Battery Tool Kit - 4 Ton Latch Head3-525441-0 Wire Plug Gauge 4 AWG

3-525441-2 Wire Plug Gauge 6 AWG

3-525441-3 Wire Plug Gauge 2 AWG

1901002-2 Dies for Battery Tool Kit - 4 Ton Latch Head3-525441-5 Wire Plug Gauge 8 AWG

1901600-1 CERTI-CRIMP II SAHT - Long Handle525442-2 Wire Plug Gauge 18 AWG Crimp Chamber (2 Dots Orange)

525442-3 Wire Plug Gauge 16 AWG Crimp Chamber (1 Dot Orange)

525446-4 Insulation Slip Gauge 18-16 AWG Crimp Chamber

Revised 5/18/2017 Page 28 of 29A certificate of calibration is included with each gauge supplied

Gauge to Hand Tool cross reference Data Sheet

1901600-2 CERTI-CRIMP II SAHT - Short Handle525442-2 Wire Plug Gauge 18 AWG Crimp Chamber (2 Dots Orange)

525442-3 Wire Plug Gauge 16 AWG Crimp Chamber (1 Dot Orange)

525446-4 Insulation Slip Gauge 18-16 AWG Crimp Chamber

1901611-1 CERTI-CRIMP II SAHT - Long Handle525442-1 Wire Plug Gauge

525446-1 Insulation Slip Gauge 24-22 AWG Crimp Chamber

525446-2 Insulation Slip Gauge 20 AWG Crimp Chamber

1901611-2 CERTI-CRIMP II SAHT - Short Handle525442-1 Wire Plug Gauge

525446-1 Insulation Slip Gauge 24-22 AWG Crimp Chamber

525446-2 Insulation Slip Gauge 20 AWG Crimp Chamber

1901657-1 'U' Die Indenter3-525441-5 Wire Plug Gauge 8 AWG

1901657-2 'U' Die Indenter3-525441-0 Wire Plug Gauge 4 AWG

3-525441-2 Wire Plug Gauge 6 AWG

3-525441-3 Wire Plug Gauge 2 AWG

1901657-3 'U' Die Indenter3-525441-1 Wire Plug Gauge 1/0 AWG

4-525441-0 Wire Plug Gauge 2/0 AWG

4-525441-2 Wire Plug Gauge 3/0 AWG

4-525441-3 Wire Plug Gauge 4/0 AWG

1976441-1 Die-set - Hydraulic Head Closed (Shank Die)2-525441-2 Wire Plug Gauge 2/1 AWG

525443-9 Insulation Plug Gauge 2/1 AWG

Revised 5/18/2017 Page 29 of 29A certificate of calibration is included with each gauge supplied