toll-plaza-boq-p-04

8/20/2019 toll-plaza-boq-p-04

1/27

Package-4

Item Description Unit Quantity Rate (Rs.) Amount (Rs.)

101 Clearing & Grubbing SM 2,500.00

104 Compaction of Natural Ground SM 2,500.00

106a Excavation of Unsuitable Common Material CM 50.00

108aFormation of Embankment from road way

Excavation in common materialCM 142.00

108cFormation of Embankment from Borrow

Excavation in common materialCM 300.00

109a Sub-grade preparation in earth cut SM 3,300.00

Bill No-01: EARTH WORKS

TOTAL (Rs.)

CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)

AT KM-320BILL OF QUANTITIES


2/27

Package-4

Item Description Unit Quantity RATE (Rs.) Amount(Rs.)

201 Grainular Sub base CM 1,785.00

202 Aggregate Base Course CM 1,161.00

203a Asphaltic Base course Class-A CM 700.00

209a Breaking of existing Road pavement CM 1,770.00

TOTAL (Rs.)


AT KM-320

BILL OF QUANTITIES

Bill No-02: SUB BASE & BASE COURSE


3/27

Package-4

Item Description Unit Quantity Rate (Rs.) Amount (Rs.)

302aCut-Back Asphaltic for Bituminious

Prime coatSM 3,615.00

303aCut-Back Asphaltic for Bituminious Tack

coatSM 3,500.00

304 b Double SurfaceTreatmentin Shoulder SM 1,733.00

305bAsphaltic Concrete Wearing Course

Class-BCM 173.00

TOTAL (Rs.)


AT KM-320

BILL OF QUANTITIES

Bill No .03: SURFACE COURSE & PAVEMENT


4/27

Package-4

Item Description Unit Quantity RATE (Rs.) Amount (Rs.)

107a Structural Excavation CM 50.00

107d Grainular Back fill CM 70.00

107e Common Back fill CM 150.00

401a1iiConcrete class-A1 (on ground) for rigid

pavement and barrier.CM 1,320.00

401bConcrete Class-B for drain & protection

workCM 6.00

401f Lean Concrete CM 625.00

404aReinforcement as per AASHTO M-31 Grade-

40Ton 2.00

404bReinforcement as per AASHTO M-31 Grade-

60Ton 14.00

410 Brickwork for manhole crash barrier etc CM 33.00

TOTAL (Rs.)



Bill No .04: RIGID PAVEMENT & DRAIN


5/27

Package-4

Item Description Unit Quantity RATE (Rs.) Amount (Rs.)

601diPrecast Reinforce Concrete Kerb new jersey

barrier for median (double face)M 100.00

SP-601diPrecast Reinforce Concrete Kerb new jersey

barrier for median (one face)M 107.00

601dii

Precast Kerb in Concrete Class-A1 of size

450x150mm including concrete bedding &

hauching.

M 967.00

604a Metal Guard Rail M 145.00

604d Steel Post of Metal Guard Rail M 55.00

607a Traffic Road Sign Category 1 Each 4.00

607b Traffic Road Sign Category 2 Each 4.00

607c Traffic Road Sign Category 3(a) Each 4.00

607e Traffic Road Sign Category 3(c) sm 10.00

608h1Pavement Marking in reflectorized CR Paint

150mmM 1,250.00

609cReflecting Pavement studs raised profile type

single sidedEach 900.00

NSI-1Providing and placing of RCC pipe 228mm diafor drainage complete with all respect as per

drawings.

M 240.00

NSI-2Apply 03 coats plastic emulsion paint as

specified.SM 2,700.00

NSI-3Providing and placing plastic Drums with

sand in position as per drawings.Each 465.00

NSI-4Providing and placing soft wooden blocks

(0.3x0.3x0.3m) in position.Each 151.00

NSI-5Providing and placing polythene sheet under

rigid pavement.SM 4,183.00

NSI-6

Providing and placing 60mm thick tuff tiles

paving or equal for foothpath and parking

area near building.

SM 500.00

NSI-7

providing all the material as per Drawings &

specifications and making of expension joints

as instruction of engineer in-charge.

M 320.00

NSI-8

providing all the material as per Drawings &

specifications and making of construction

joints all as instruction of engineer in-

charge.

M 300.00

TOTAL (Rs.)



Bill No .05: ANICILLARY WORKS


6/27


7/27

Concrete (1:2:4) Class 'C' Cylindrical Compressive Strength f'c=

3000 psi excluding steel and its bending but including shuttering

centering and its binding as per drawing and specifications and

as directed by Project Manager.

i. Footing Cu m 73.12

ii. Column Cu m 45.41

v. Coping Concrete 3" thick over Parapet Wall as shown in

drawing.Cu m 20.47

vi: RCC Roof Beams Cu m 33.97

vii: RCC Roof Slab Cu m 63.20

viii. RCC Iintel/Sill beam, Jamb column in doors /windows, Pea

rock Concrete Grout (f'c= 3000 psi) in external walls of the building Cu m 67.94

ix. RCC stairs Cu m 9.23

Providing Reinforcement Steel (Grade-60) including cutting,

bending.

Placing and binding wire.

i. Footing

ii. Column

iii. Plinth beam

iv. Brick Masonry

vi. Roof Beam

viii. Roof Slab

ix. Mumty Slab

x. RCC lintel/Sill beam/Jamb columns

ix. RCC Stairs

6a

Bitumen coating 2 coats of Bitumen 0.41b/ft2 (0.21b/ft2 per coat

of 40/60 grade) allbuild surface of foundations, Plinth beam sides

exposed to earth, top suface of Plinth beam and Column exposed

to earth f ill in approved manner and as directed by Project

Manager.

Sq m 450.00

6b

Providing and lying 1-1/2" Class C cast in Situ using Find sand

mixed with any approved water proofing agent Sq m 100.00

Stone Soling

Providing, Laying, compacting and blocking 4" thick 'Stone soling

With 2" down gauge gradedStone Blastwith Stone dust filling and

finesand aggregates Overprelaidand precompacted fill, backfillas

per specification. (provided for separately).

i. Under Floors Cu m 45.87

8

i) Vapour Barrier

Providing and Laying of Polythene Sheet 500 gauge (0.005")

thick prime quality laid over stone soling for Flooring Plinth

Protection and ramp as per Specification and as Approved by the

Engineer.

Sq m 483.87

First Class burnt brick masonry Work with cementsand mortar i/c

curlng etc comp1ete in aII respecti) 9" thick Wall with 1:4 cement sand mortar with deep stuck

Pointing (Ironed Joint by using 10mm round bar to create half

grout neck) both horizontally and vertically only on outer wall

surface of the building as per drawing and as approvd by the

Project Manager

Cu m 128.56

ii). 9" thick Wall with 1:4 cement sand mortar in ordinary finishCu m 13.50

iii). 4.5" thick Wall with 1;4 cement sand mortar in ordinary finish.Cu m 15.43

Plaster, 1/2 inch thick on Walls Columns Ceiling inclluidig floating

coat unde plaster.

i. On internal and External walls/columns with 1:4 cement sand

morterSq m 527.43

ii. On Ceiling/Column with 1:3 cement sand mortar Sq m 463.21

7

9

10

5

Tons 28.20

4


8/27

i ii . Providing applying Aluminium Wire Mesh under Plaster

including

Corner Beads.

Sq m 55.00

Painting:

i) Internal (plastic emulsion paint) 3 coats from reputed

manufacturer as per spcification in approved mannerSq m 527.43

ii) Internal (Enamel paint) 3 coats from reputed manufacturer as

per spcification in approved mannerSq m 79.50

iii) External (eeather shield paint) 3 coats from reputed

manufacturer as per spcification in approved mannerSq m 272.88

Celling Work

i. P/F Plaster of Paris concrete/gola (4"x5") as per specifications

including nailing/screwing as aproved by the Engineer. Mtr 27.72

Floor Ffriishing

i. Providlng and layingof prime quality 8-9mm thick 16 "x 16'' full

bodyPorcelienTilesfor flooring over3/4'thick i:2 .Cement sand

morter bed with approved Porcelain Bonding materia I and

floating coat of cement and as per speifications and approved

by the Project Manager.

a . 16" x.16' Pre- Polished

Sq m 401.71

ii. Providing andlaying of prime quality,local, make, 5mm thick or

more glazed ceramic tiles for Bathroom Flooring as per

speifications and as approved by the Engineer.Sq m 35.00

iii. Providing and fixing of prime quality pakistani,3/4"thick pre-

polished Travera/Botesena or equivalent Marble Slab 24" Wide x

4' long over bed of 3/4" thick 1:2 Cement sand mortar with

floatirig coat of cement including making ground edge (bull nose)

to marble, grinding, pol ishing, fil ling the joint complete in all

respect as shown in drawing and as approved by the Engineer.

Sq m 4.50

Skirting

i. Porcelain tiles for skirtirig:

Providing and layig 8-9mm thick Pre polished 5"-6" wide"x 16"long Porcelain tile for skirting as shawn in drawing with

approved quality tile bonding material as per specifications and

as approved by the Project Manager.

Sq m 26.37

ii. Marble tiles for skirting:

Providing and laying of prime quality 1/2" thick 6"x12" Pre

Polished Marble tile (Pakistan parlino or equvalent) for skirting

with1:2cement sandmortar asshown indrawings in approved

manner as per specifications i/c finishing etc. complete in all

respects and as approved by the Engineer.

Sq m 1.65

15

Ceramic tile for dado(bathroom walls):

Approved prime quality, local make, 5mm thick or higher ceramic

tiles for

dado or skirtingas shown in drawing as per specifications and

as approved by the Engineer.

Sq m 47.50

16

Roofing

P / L roofing comprising of single layer of tiles 9"x4 1/2"x1 1/2"

(225 x113x40 mm) grouted in 1:3 cement sand mortar with water

proofing agentlaid over 1"mud plaster without Bhoosa, over 3" to

2" earth, over polythyne ,over 1" high density thermopore (Poly

Urethene) sheet (tongue and grove),over polythyene over 2

coats of hot bitumen priming coat over RCC Slab complete in all

respect as shown in drawing and as approved by the Project

Manager.

Sq m 453.08

11

12

13

14


9/27

17

Doors Frame:

Vi) Providing and fixing of 1-1/2" thick single leaf Wooden

solid pannaled/patrened door having Deodar wooden framing

1 1/8" thick with 6" Widetop rail, 6" wide middle railand 9" wide

bottom rail with 5mm thick pressed teak ply With

impression/design on both side i/c 1-1/2 x 3/8" deodar wood

lipping allaround theshutter,with9" botom rail ,8 " wide lock rail

& 6" Wide topraili/c brass hinges (4 Nos.),all fitting. frenchpolish

3 coats and door handles, imported handle lock and tower bolt

etc. complete in allrespectas shown indawing as approved bythe

Project Manager.

Sq m 72.00

Windows

Providing and fixing of glazed AIuminum Windows of anodised

bronze (15 micron) colour partly fixed and partly sliding using

deluxesectionshaving frame size of 100mm x20mm (4"x3/4")and

leaf frame sections of 50mm x 20mm (2"x3/4"), all of 16mm

thickness including 5mm thick imported reflected glass with

rubber gasket usingapproved standard latches, . hardware, etcas

shown in drawing and as Approved by the Engineer

ii. 2Panel Mercury glass with matel insect screen with aluminium

frame.Sq m 33.26

19

Ventilators Providing and fixing

Aliminium Ventilator of top huged anodized (15 micron) bronze

having frame size 100mm wide x 20mm high x 1.6mm thick

sections including 5mm thick imported solar reflective tinted glass

withrubber gasket using approved standard latches, hardware etc

as shown in drawing and as Approved by the Engineer.

Sq m 9.00

20

Security Grill Providing and fixing of Security Gri ll in window

including 1/2"x1" steel tube frame having 1/8" wall thickness

anchored to walls with 1/4" dia concrete anchors 1/2"x1/2"steel

bars vertical and horizental weided to steel tube frame as shown

on drawing i/c painting 3 coats complete in all respect and as

approved by the Project Manager.

Sq m 33.26

Carpentry in Kitchen Provinding and fixing in position KitchenWooden Cabinets Consisting of 1-1/2"x1-1/2"thick Deodar wood

frame with 3/4" thick both sides laminated Vinboard boxing

selves,shutters with best quality fittings, all

hardware,nails,handles, hinges, complete in all respects as per

design and drawing and as approved by the Engineer

i- Wall Mount Cabinets Sq m 15.92

ii- Under Counter Cabinets Sq m 6.89

i ii (c)- Providing and laying of 1" thick Marble slab on Kitchen

Counter as Shown in DrawingSq m 5.00

i) Providing and fixing of Collapsible Security Gate (Scissor Type)

made of 2"x3/8" steel bar at top vertical steel channal

3/4"x1/2"x1/2"x1/8" at 4" c/c (approximately) steel flat crosses

5/8" with best quality roller at top of 1-1/2" diameter run on top

steel bar and 1-1/2"x1-1/2"x3/16"angle at each side anchored to

substrate including three hold fast per side steel pins and spacers

,12"long handle,locking arrangment inside andout side, 3 coats of

painting of black japan cnemeled, complete in all respects as

shown in drawing and approved by Project Manager.

Sq m 19.20

ii) Providing and fixing of Hinged Security Gate Consist of1-1/2"x1-

1/2"1/8" steel bar at top, middle and bottom, vertical steel flat 1-

1/2"x1/4" at 3" c/c (approximately) steel flat crosses 1-

1/2"x1/4"includingthree holdfast per side 12' long handle, locking

arrangement inside andout side,3 coats of painting of blackjapan

cnemeled, complete in all respects as shown in drawing and

approved by Project Manager.

Sq m 39.35

TOTAL (Rs.)

18

21

22


10/27

Package-4

Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)

1

Water Closet , English, prime quality, in vitreous china clay,

Large size with Porcelain P-trap, plastic body low level 12,

liters flushing cistern, Ball type non corrosive siphon valve,

flush handle , PVC drain pipe all in prime quality local make

as approved by the Project Manager

Nos 3.00

2

Water Closet , Pakistan Orissa, prime quality, in

vitreous china clay, Large size with Porcelain P-trap,

plastic body low level 12, liters flushing clstern, Ball

type non corrosive siphon valve, flush handle , PVC

drain pipe all in prime quality local make as approved

by the Project Manager

Nos 6.00

UPVC Pipe for waste and sewage Internal drainage

including Vents with cap, properly laid jointed

Including branches bends, Ys, tees, fitting, clamps,

specials, cutting in floors, walls and making good,

extra painting ion pipe to match the color of the

building testing, complete in all respect.

110mm Pipe Mtr 95.00

73 mm Pipe Mtr 20.00

Provideing, laying, cutting, jointing, testing and

dislnfecting PPRC pipeline in trenches/walls, with

socket joints, all pipe specials using PPRC Pipe of DIN

8077 & 8078 rating PN 20 complete in all respects,with specials and valves

50mm pipe Mtr 25.00

40mm Pipe Mtr 80.00

25mm Pipe Mtr 90.00

Providing, laying, cutting, jointing, testing and

disinfecting PPRC pipeline in trenches, with socket

joints, using G.l. Pipe of B.S.S. 1387-1967 complete

in all respects, with specials and valves (Medium

Quality)

25mm Pipe Mtr 35.00

5

Gully trap with RCC cover, Cement Concrete chamber

size 6''x 8''x6'' deep in smooth finish Inside & outside,

with 3’’ cast Icon P trapNos 4.00

Providing and Fix ing Wash hand basin with pedestal in

approve color prime quality including angle iron bracket set

waste pipe, waste coupl ing complete in all respects as

Approved by the Engineer Accessories for Wash Hand Basin

are:

Nos 10.00

i . Water Mixer of Faucet for basin/sink complete in all

respectNos 11.00

ii. Connecting Pipe Nos 22.00

7

Providing and fixing of best, quality imported Looking Glass

5mm thick including cost of fi tt ing as Approved by the

Engineer

Sq m 6.75

BILL OF QUANTITIES

3

4

6


AT KM-320

Bill No. 06B - PLUMBING WORKS


11/27

Providing andFixing of Approved prime Quality plastic body

Bath Room Accessories Including cast of fitting as

Approved by the Engineer including follow:

i. Towel Rail Nos 5.00

ii. Soap Dish Nos 5.00

iii. Tissue Paper Holder Nos 9.00

9

Providing and Fixing PVT floor trap 4''x3'' with concrete

chamber al l around and 4' ' PVT grating complete in all

respects as Approved by the Project ManagerNos 17.00

Providing and Fix ing brass valves with wheel/handle,

threaded ends all in premium quality local make in internal

as follows:

50mm dia Nos 2.00

40mm dia Nos 2.00

25mm dia Nos 2.00

Providing and fixing of good quality non return valve with

male and female ends

50mm dia Nos 2.00

12

Providing and fixing of plastic body prime quality Muslim

Shower including PVT flexible pipe and CP/Powder coated

Double Bib Cock as Approved by the EngineerNos 9.00

13

Providing and fixing of good quality CP/Powder Coated1/2''

Double Bib Cock as Approved prime quality as Approved by

the Engineer

Nos 9.00

14Providing and fixing 1/2'' dia CP/Powder Coated prime

quality as Approved by the EngineerNos 22.00

15

Providing and fixing of steel body prime quality showers

Roes including detachable l id pipe as Approved by the

Engineer

Nos 3.00

16

Providing and Fixing approved quality stainless steel sink

33'' x 18' ' Pak made complete with angle iron brackets fix

into walls ,1/2' ' chromium plated sink faucet , 1-1/4' '

chromium plated brass waste coupling, unions and PVTdrain pipe, complete in all respect and Approved by the

Engineer

Nos 1.00

17

Providing and Fixing of prime quality Gas Burn with Triple

Burner stainless steel body with all fixture, PVC gas piping

work upto specified location in kitchen, complete in all

respect and as Approved by the Engineer

Nos 1.00

18

Providing and Fixing of 110mm Dia PVC Class-D Rain Water

Down pipe with shoe , bends in Ducts including clamps, hold

fast as required with the provision of clean out, complete in

all respect and Approved by the Engineer

Mtr 30.00

19

Providing and fixing of foot drain including making gutter

and perforated drain covet as shown on drawing Nos 6.00

11

TOTAL (Rs.)

8

10


12/27

Package-4Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)

16030t Supply and wiring for light & fand with 3x1.5mm sq single core, PVC

insulated stranded copper conductor wire in 20mm (3/4") dia PVC

conduit recessed in the wall of column, roof etcirequired complete

in all respects as approved by the Engineer (Beta Polo Conduit /

Pakistan, New Age, Fast Cable)

Point 67.00

16030s Supply and wiring for circuit with 2x2.5mm sq, PVC insulated

300/500 voltage grade single core stranded copper conductor wire

directly from DB in 20mm (3/4") dia PVC donduit including 1x1.5mm

sq cable as ECC recessed in the wall column and roof atc as required

complete all in respects as Approved by the Engineer, (Beta Polo

Conduit / Pakistan, New Age, Fast Cable)

Point 14.00

16030x Supply and wiring for light sockets with 2x2.5mm sq + 1x1.5mm sq

PVC, insulated 300/500 voltage grade single core stranded copper

conductor wire directly from DB in 25mm (1") dia PVC donduit

recessed in the wall column and roof atc as required complete all in

respects (Beta Polo Conduit / Pakistan, New Age, Fast Cable)

Point 16.00

16030y Supply and wiring for power sockets with 2x4mm sq + 1x2.5mm sq

PVC, insulated 300/500 voltage grade single core copper conductor

wire directly from DB in 25mm (1") dia PVC donduit recessed in the

wall column and roof atc as required complete all in respects (Beta

Polo Conduit / Pakistan, New Age, Fast Cable)

Point 14.00

16030x Supply and wiring for switch sockets to sockets with 2x2.5mm sq +

1x1.5mm sq PVC, insulated 300/500 voltage grade single core

stranded copper conductor wire directly from DB in 20mm (3/4")

dia PVC donduit recessed in the wall column and roof atc as

required complete all in respects.

Point 26.00

16030z Supply and wiring for Ari conditioning power soecket of 1x2.5mm sq

PVC, insulated 300/500 voltage grade single core stranded copper

conductor wire directly from DB in 25mm (1") dia PVC donduit

recessed in the wall column and roof atc as required complete all in

respects as approved by Engineer. (Beta Polo Conduit / Pakistan,

New Age, Fast Cable).

Point 8.00

Supply and wiring of 4 core PVC / PVC / CU, calbe of 600/1000 V

graded in all kinds of existing or given prelaid, pvc conduit in

approved manner as shown in drawing complete in all respects, as

approved by the Engineer.

i) 4 Core 120mm² PVC / PVC / CU cable Mtr 53.34

ii) 4 Core 35mm² PVC / PVC / CU cable Mtr 71.62

Iii) 4 Core 25mm² PVC / PVC / CU cable Mtr 114.29

iv) 4 Core 16mm² PVC / PVC / CU cable Mtr 109.11

v) 4 Core 10mm² PVC / PVC / CU cable Mtr 45.11

Supply and wiring of single core PVC cable 450/750 Volts grade in

prelaid pvc conduit as ECC with power calbe in approved manner as

shown in drawing complete in all respects, as approved by the

Engineer. (Pakistan, New Age, Fast)

i) 1x6mm sq Mtr 137.15

ii) 1x4mm sq Mtr 106.37

iii) 1x2.5mm sq Mtr 109.11


Bill No. 06 C - ELECTRICAL WORKS

AT KM-320

BILL OF QUANTITIES

The rate for all BOQ item shall include providing, construting, fabricating, fixing, executing, applying, as applicable and additionally as otherwise stated against the

specific items shall include all materials, labor, efforts, plant and equipment, complete in all respects, as per drawings, approved shop drawings, specifications, as

per NEC, NFPA 70 & NEMA, various applicable stipulations, miscellaneous details, as per instruction and as directed by the Engineer. All sampels shall be procured

and provided by the contractor at his own cost for approval by the Engineer.

16030d

16030d


13/27

Providing and laying PVC conduit conforming to BS-6099 and BS-

3506 including excuation back filling, pull boxes, spection boxes,

tees, bends, crosses, using accessoties for proper sealing joints, in

roof slabs, walls and under floors for power calbes including cutting

in wall and floors as required, back filling and making good the cut

cavities with cement sand mortar all in approved manner as shown

or drawings, complete in all respect as approved by the Engineer

(Beta Polo)

i) 100mm dia Mtr 45.72

ii) 50mm dia Mtr 104.24

iii) 40mm dia Mtr 257.54

iv) 25mm dia Mtr 99.06

Supply, installation and connecting of gang, switches one or two

way with plastic back box including wall cutting, fixing etc, and

making good complete in all respect as approved by the Engineer

(Clipsal, Legrand)

ii) 2 gang 1 way light controll switch Each 6.00

iii) 3 gang 1 way light controll switch Each 5.00

iv) 4 gang 1 way light controll switch Each 8.00

v) 5 gang 1 way light controll switch Each 4.00

vi) 6 gang 1 way light controll switch Each 14.00

16020h Supply, insta llat ion, connecting and testing prime quali ty fan

dimmer with switch with plasti c /pvc back box complete in al l

respects as approved by the engineer (Clipsal, Legrand) Nos 21.00

16020c Supply, insta llat ion and fix ing 13, Amps provcarbonate f lame

retardant 3 pin, Mulitpurpose swithch, socket unit with fancy gang

plate fixed on die fabricated power coated metal board recessed in

wall or comumn including connectinos as required (Vivace intl

socket Clipsal make), complete in all respects

Nos 43.00

16020c Supply, insta llat ion and fix ing 15, Amps provcarbonate f lame

retardant 3 pin, swithch, socket unit with fancy gang plate fixed on

die fabricated power coated metal board recessed in wall or

comumn including connectinos as required (Vivace intl socketClipsal make), complete in all respects

Nos 21.00

16050c Supply, installation, connecting and testing of fluorescent tube light

fitting fixture, 4' length with frame diffuser, electronic ballast ande

28 watts fluorescent TLStuberod cool day light lamp as Phlips TMS

215 Slimline complete in all respects as Approvec by the Engineer,

(Philips pierlite, Osram)

Nos 16.00

16050c Supply, installation, connecting and testing of fluorescent tube light

fitting fixture, 4' length, complete with frame diffuser, electronic

ballast ande 2x8 watts fluorescent TLS tube rod cool day light lamp

as Phlips TMS 225 Slimline complete in all respects as Approvec by

the Engineer, (Philips pierlite, Osram)

Nos 6.00

16050c Supply, installation, connecting and testing of 2'x2' fluorescent tube

light fitting fixture, complete with electronicballast ande4x18 watts

fluorescent TLS tube rod cool day light complete in all respects asApprovec by the Engineer.

Nos 8.00

16050e Supply, installation, connecting and testing of 1x23W recessed typy

Energy Saver Down Light wi th Bakeli te lamp holder ref lector

(Imported) fitting complete with 1x23 watts CFL lamp as per Philips

Cat, No. FBH 145/1x18 W PLC, complete in all respects as required

as Approvec by the Engineer.

Nos 44.00

16050d Supply, installation, connecting and testing of 1x23 W head lamp

holder, reflector (Imported) fitting complete with 1x23 watts CFL

lamp complete in all respects as required as Approvec by the

Engineer. (Philips, Plerite, Osram)

Nos 12.00

16040b

16020b


14/27

16050d Supply, installation, connecting and testing of water proof light IP54

complete with electronic ballast, splash profcasing and 1x36 watts

flurescent tube rod complete in allrespects as required as Approvec

by the Engineer. (Philips, Plerite, Osram)

Nos 9.00

16060e Supply, installation, connecting and testing of 56'sweep ceiling fand

with ceiling rose ceiling hook, fan box, matching GI pipefor suitable

hight wiring upto termination point complete in all respects as

Approvec by the Engineer. (GFC, Climax, Royal)

Nos 13.00

Supply, installation, connecting and testing of electric exhaust fan

including metal , louvers, ON / OFF swithc, calbe, complete in all

respects as Approvec by the Engineer. (GFC, Climax, Royal)

iii) 12" Metal Body Nos 9.00

iv) 18" Metal Body Nos 1.00

16060d Supply, installation, connecting and testing of 450m (18") sweep

wall bracket fanwith blades, housingregualtor & pulling cordswitch

fitted on wall or column with GI clip ncluding connection as required

complete in all respect as approved by the Engineer.

Nos 9.00

16110 Tubewell

Providing and construction of Tube Wll with dia boring installed

with S" dia SM 14 guage blind pipe, steel strainer. The space

between boring wall and MS pipe sahll be fil led with coarse sand

1/8" min and 3/8" max in size. The tube well shall be installed with

4" dia 1.5 K.W submercible pump 1" dia GI / HDPE pipe (PE.63)

suction pipeas pe rrequirement with respect to ground water, table

Electricl Fanel including Circuit breaker, U/OVT relay and plugs PF

improvement panel, Soecket RCC pump shade / cover complete in

all respect and as per the approval of the Engineer. The length of

stainer will depend upon the ground water table and water bearing

starta with a minmum 50 ft length. Submercible pump is suppored

by 8mm steel insulated wire power cable shall be wraped water

proof tape as shown in drawing SB GOLDEN PUMPS)

Mtr 38.10

16110 Providing , fixing, connecting and testing of (as per manufacturerrecommendations) AC single phase pumping set 2HP rating 220

volts, 50 cycles electric motor with centrifugal pump compatible

withmotor suction and discharge 1" x 1" coupled ona comportbase

plat. Foundaton bolts 1" dia GI piping connections and required

bends, sockets tees, unions etc, gate valve, check valve non-return

valve foot valve and strainer at UGT sump level a per drawing ,

Electrical Panel including Ciruit bradker, U / OVT relay and plulgs,

sockets PF improvement panel RCC pump shade / cover, complete

in all respect and as approved by the Engineer ( KSB, GOLDEN

PUMPS)

Job 1.00

Distrubution Boards

16060d


15/27

16070 Supply, installation, connecting and testing of Main, panel board

consisting of 14 SWG M.S powder coated indoor floor mounted and

sui table foundation compelte with al l internal wir ing, tags ,

identification labels, TPN&E copper, bus bards, gransparent plastic

sheet armoured glands lockable covers, cable brass glands where

reqired consisting as follows additinally conforming / complying

with details as shown on drawings complete in all respect as

approved by the engineer (ABB, MG GE or Eqv)Incoming

01 No. 200 Amps T.P 35 KVA MCCB ADJUSTABLE circuit breaker

(ABB or equivalent)

03 Nos - Indication Lamp

01 No - Voltage Selector Switch

01 No - Volt meter (Digital) 7 Point

01 No - Current Selector Switch

01 No - Current Meter (Digital ) 5 Point

06 Nos - 2 Amps Fuses

Out Going

01 No. 100 Amps TP RC25KA MCCB

01 No. 16 Amps DP RC 15 KA MCB

01 No - 25 Amps TP RC255KA MCB

01 No - 63 Amps TP RC25KA MCCB

02 No - 30 Amps TP RC25KA MCCB

Suitable Common Copper Bus BarNatural and Earth Bus Bars

Nos 1.00

16070 Supply, installation, connecting and testing of distribution board

(Building DB) consi sting of 16 SWG M.S Powder coated indoor

recessed tyupe mounting front door access complete with al l

interval wiring tags indentification lables, TPN&E copper bus bards

transparent plastic sheet,lockable, covers, cable brass glands where

required consisting as follows additionally conforming / complying

with detail s as shown on drawings, complete in all respect as

approved by the Eng ineer (ABB, MG, GE or Fqv)complete in al l

respect as approved by the engineer (ABB, MG GE or Eqv)

Incoming

01 No - 100 Amps T.P MCCB 25 K circuit breaker

03 Nos - Indicatio Lamp

01 No - Volt Meter (Digital) 7 Points

01 No - Volt Selector switch

03 Nos - Vuses

Out Going

Nos and ratng S.P of MCB circut breaker

09 Nos - 06 Amps SP MCB RC10KA


09 Nos - 16 Amps SP MCB RC10 KA


Suitalbe Common Copper Bus Bar

Natureal and Earth connector

Nos 1.00


16/27


(Genset Room) consisting of 16 SWG M.S Powder coated indoor

recessed type mounting front dooraccess complete with allinterval

wiring tags indentificatino lables, lockable covers, ccalbe brass

glands where required TPN&E copper bus bards transparent plastic

sheet, consisting as follows additionally conforming / complying

with detail s as shown on drawings, complete in all respect as

approved by the Engineer (ABB, MG, GE or Fqv)

Incoming

01 No - 20Amps DP MCB 15Ka ciruit breaker



01 No - Volt Selector swithc

03 Nos - fuses

Out Going

Nos and ating S.P of MCB circuit breaker

01 Nos - 06 Amps SP MCB RC10 KA

01 No. - 10 Amps SP MCB RC10KA


Suitable Common Copper Bus Bar

Natural and Earth connector

Nos 1.00


(INTERCHANGE FLOOD LIGHT) consisting of 14 SWG M.S Powder

coated indoor recessed type mounted and suitable foundation,

weather proof IP54 including front door access complete with all

internal wi ring tags indenti fi cation lables , Photo censor and

mounting bracket of Photo sensor for Auto Switching of l ights,

nagnetic contracors, Fuses, TPN&E copper bus bards transparent

plastic sheet, lockable covers, cable brass galnds where required

consisting as fol lows additionally conforming / complying with

details as shown on drawings, complete in all respect as approved

by the Engineer (ABB, MG, GE or Fqv)

Incoming

01 No - 20Amps Three POLE MCCB 15Ka ciruit breaker



01 No - Volt Selector switch03 Nos - fuses

01 No - Photo light sensor for auto light swithces

Out Going


01 Nos - Magnetic Contractor 25A

01 No. -




Nos 1.00


17/27

16070 Supply,installation, connectingand testing of distribution board (DB

ROAD LIGHT) cons is ting of 14 SWG M.S Powder coated indoor

recessed type mountedand suitable foundation,weather proof IP54

including front door access complete with all internal wiring tags

indentification lables, Photo censor and mounting bracket of Photo

sensor for Auto Switching of l ights, nagnetic contracors, Fuses,

TPN&E copper bus bards transparent plastic sheet, lockable covers,

cable brass galnds where required consisting as follows additionally

conforming / complying with details as shown on drawings,

complete in all respect as approved by the Engineer (ABB, MG, GE

or Fqv)

Incoming





03 Nos - fuses


Out Going





Nos 1.00


(CANOPY LIGHTS) consisting of 14 SWG M.S Powder coated indoor









or Fqv)

Incoming





03 Nos - fuses


Out Going



05 No

01 Nos. 16 Amps SP MCB RC10KA




Nos 1.00


18/27


(TOLL BOTH DB) consisting of 14 SWG M.S Powder coated indoor









or Fqv)

Incoming





03 Nos - fuses

Out Going



05 No


02 Nos. 16 Amps SP MCB RC10KA01 Nos - 20 Amps SP CMB RC10KA



Nos 4.00

Grounding Work

16090 Supply, installation connection, boring / excavation and testing to

less than 1 ohmof earthing set with 20mm dia 3 meter long copper

rodencased in 3" dia pvc pipelowerede and burreed inground in4"

dia boring in all type of soil to water table at required depth, plated

connected with 1x70 mm sq HDBC bare cu-conductor from

grounding rod to earth lest copper bar as earth connecting point,

the remaining cavity around the copper rod shall be fil led with

gournding enhancement compound packed hard all around the

copper rod for MDB grounding pole l ight gounding and lighting

protection gounding complee in all respect as approved byt the

engineer.

Job 3.00

16090 Supply, insta llation 12" long 2", wide 1/2" thick (12"x2"x1/2")

copper bus bar as earth connecting point (ECP). The (E.P) shall be

complete with insulator, washers, nuts, bolts, mounting installation

and operational accessories as per technical specificaiton and as per

site requirement complete in all resepct as approved by the

engineer.

Job 3.00

16090 Supply, installation and wiringof singlecore1x70mmsq PVC copper

wire 600/1000 volts grade in prelaid pvc conduit from ECP to MDB

as ECC conductor in approved manner as shown in drawing

complete in all resepct as approved by the engineer (Pakistan, New

Age, Fast Cable).

Mtr 21.33

16090 Supply and construction of 2ftx2ft and 2ftdeepbrick Masonryhandhole to cover earthing GI pipe tee i/c comented door, inside 1:4

plaster and 1ftx1ft RCC cover flush on floor complete in all respect

as Approved by Engineer.

Job 3.00

16090 Supply and insta llat ion of 1 1/2" x 1/3" copper str ip from top of

building (lighting spike) to ECP earthing point inclading brass saddle

at 1 ft interval, brass screw etc complete complete in all respect as

Approved by Engineer.

Mtr 15.24

16090 Supply and insta llation on top of bui lding 1" dia meter 3ft long

lighting copper rodwithballand five spikes fix on head complete in

all respect as Approved by Engineer.

Job 1.00

Road pole lighting


19/27

16050g Supply and installation of mild steel tubular swaged / welded siliver

enmeled painted road l ight single arm pole of over all length 10

Mtrs hav ing 3 steps and dimension of 150x100x75mm & tube

thickness 6.5.4mm respectively for fixing road light complete with

M.S baseplate having 20mm thickness and 300sqmm long corved

bracket with 800mm radius for mount ing l ight f ixture with al l

required civil works (including PCCfoundaionswherever required as

pe relevant standards and as per instructions) with sui table

precautions for ensuring prevention of watering ressand proper

water proof termination of calbes and wires complee naneatand

satifactory manner complete in all respect as Approved by the

Engineer.

Job 8.00

16050g Supply and installation of mild steel tubular swaged / welded siliver

enmeled painted road light double singlearm pole of over alllength

10 Mtrs having 3 steps and dimension of 150x100x75mm & tube

thickness 6.5.4mm respectively for fixing road light complete with

M.S baseplate having 20mm thickness and 300sqmm long corved

bracket with 800mm radius for mount ing l ight f ixture with al l

required civil works (including PCCfoundaionswherever required as

pe relevant standards and as per instructions) with sui table

precautions for ensuring prevention of watering ressand proper

water proof termination of calbes and wires complee naneatand

satifactory manner complete in all respect as Approved by the

Engineer.

Job 6.00

16050d Supply, fixing and installation of Road lighting luminaire suitalbe on

pole foruse with High PresureSodium Vapour Philips SGP 338SON-

T 250W lamp including housng cum reflector of deep drawin

aluminum powder coated in grey colour outside and all electricla

accessories such as energy efficient copper ballast electronic ingitor

power factor improvement copacitor etc are pre-wired upto to

terminal block and mounted on a specially desinged detachalbe gear

plate. Conformance to IP 54 protection complete in all respect as

Approved by the Engineer.

Job 20.00

16070 Supply and fix ing of function box concelead in foundaton with

lockable cover, dust and wheathe proof gasket

250mmx200mmx150mm deep junction box nominal size of 16 SWG

thick MS sheet cable looping box with the existing pole with MS

clamp made out of 25mmx3mm thick at iron with suitable nuts and

bolts complete with hinged cover and locking screws earth studs

neoperene gasket suitalbe for pole mounted including supply and

fixing one no 6 Amp MCB carrier with base and 4 way + grounding

60 Amp terminal block suitable to receive PVCarmoured cable fixed

on suitable size bakel ite sheet base complete with connection

painting as required complete in all respect as Approved by the

Engineer.

Job 20.00

16040 Supply and fix ing of PVC pipe s leeve 40mm dia Nominal 2.5 mtr

length along the pole or protection of underground cable as

required (vertical length) as required, complete in all respect as

Approved by the Engineer. (Polo Beta)

Job 20.00

16030d Supply, laying, installation, glanding and termination of 3 core 2.5

Sqmm PVC insulated copper flexible cable 13meters in length in

tubular pole glands, nuts bolts, required accesssries for providing

supply to the street lights as required as approved by the Engineer

(Pakistan, New Age, Fast Cable)

Job 10.00


20/27

16030d Supply, laying , glanding, termination, testing and commissoning of

the f lowing sizes of 600/1000V grade PVT insulated and PVT

sheathed armoured copper stranded condulor 4core 16mm.sq

power cable and 6mm.sq coppperd cable as ECC connected to

grounding pit / ECPin prelaid 40mmcnduit ,complete as required as

per specifions as approved by theEngineer (Pakistan, New Age, Fast

Cable)

Mtr 284.97

Toll plaza Canopy & Flood Lighting

16050h Supply & installation of type mild steel tubular swaged/welded Road

l ihgt pole of over all length 9M having 3 sreps and dimension of

150x100x175mm & tube thickness 6-5-4mm respectively for fixing

road light complete with MS baseplate having 20mm thickness and

300sqmm long curved bracket with 800mm fadius for mounting

light fixture with all required civil works (Including PCC foundations

wherever required as per relevat standards and as per Instructions)

with suiablw precaution for ensuring prevention of watering

ressand proper water proof-terminat ion of cables and wires

completed in all stalsfactory manner as approved by the Engineer.

Job 6.00

16050d Supply. Fixing and installation of Road l ighting luminare suitable

onpole for usewith High Pressure Sodlum Vapour Philips Tango 3 T

250W lapm including housing cum reflector of deep drawn

aluminlum, powder coated in grey colour ballas electronic lgnitor,

power factor improvement capacitor etc, are apre wired upto a

terminal block and mounted on a specially designed detachable gear

plate Conformance to P 54 protection complete in all respect as

Approved by the Engineer

Job 10.00

16050d Supply f ixing and Installation of to ll plaza canopy luminaire

rececessed type Philips MPF-932 400wa-ts HPIT Muli, Ballast & lam

including housingcum reflector and allelectrical accessories such as

energy efficient multi bal last, electronic ignitor, power factor

improvement capacitor etc, are p e-wired upto a terminal block and

mounted on a specially designed detachable gear plate

Conf ormance to IP 54 protection complete in all respect as

Approved by The Engineer

Job 8.00

16050h Supply and fixing of GI Bbraketsilver enameled on top the pople for

the installation of the integral flood light luminaire at 9.5 mtr long

pole as rewuired for flood/road lights as requiredJob 6.00

16070 Supply and fix ing of junction box concelaed in foundat ion with

lockable cover ,dust and wheather proof gasket

250mmx200mmx150mm deep junction box nominal size with SWG

thick MS Sheet cable looping box with the existing pole with MS

clamp made out of 25mmx3mm thick flat iron with suitable nuts

and bolts complete with hinged cover and locking screws earth

studs neoprene gasket suitable to receive PVCarmoured cable fixed

on suitable size Baketillte sheet base complete with connection

painting as required, complete in all respect as Approved by The

Engineer.

Job 10.00

16040 Supply and f ixing of pvc pipe sleeve 40 mm dia Nominal 2.5 mtrlength along the pole or protection of underground cable as

required, Complete in all respect as approved by The Engineer (Polo

,Beta)

Job 10.00

Supply, laying , installation , glanding and termination of 3core2.5

sqmm PVC insulated copper flexible cable 10.5mtres in length in

tubular pole glands, nuts, bolts, required accessories for providing

supply to the street lights as required as approved by the Engineer

(Pakistan, New Age, Fast Cable)

Job 10.00

Supply and wiring of single core PVC cable 450/750 Colts grade in

prelaid40mm pvc conduit for flood lights and canopy recessed light

in approved manner as shown in drawing complete in allrespects as

Approved by the Engineer (Pakistan, New Age, Fast)

i) 1 x 6mm sq Mtr 571.47

16030d


21/27

ii) 1 x 4mm sq Mtr 197.20

Tranformer

16010 Design, fabrication, manufactering, supply, installation testing and

commissioning of 200KVA , 11KV/415V outdoor power transformer

including all external radiating tubes, oil filling and drainage vales

lifting lugs etc with all installation and operation accessories and

making oil pit and protection relays ,temperature alarm & devices

and separate two grounding systems for neutral and body ground

with 3mtr copper 'Road' CC foundation as per required design must

tomply all the WAPADA standards and required as per site as per

tender specification and as desired by The Engineer

Job 1.00


commissioning of prime Diesel Generator 100KVA (primary) at 0.8

PF,400voptls, the three phase, 4wire, 50hz at 1500RPM including

AVR along with ElectronicPanel and switches, tool Kit, Day fuel tank

500ltrs and essential piping systems and transportation at site and

separate two grounding systems for neutral and body grounding

with 3mtr copper road as Approved by The Engineer of the

following brands (SDMO france, PERKINS , GUMMINS UK,

MITSUBISHI Japan, CAT UK/USA, F.G. WILLSON UK)

Job 1.00


commissioning of Autoransfer switch panel for Diesel Generator

100KVA Including 75A FOUR POLE MCCB Breaker ,timer relays,

U/OVT relay, Phase failure relay Auto start ,Auto Shutdown system

and transportation at site ,as approved by The Engineer

ABB/MG/SCHCNIDER

Job 1.00


commissioning of Weather Proof and soundproof Canopy (85dB at

1m) Suitable for the above diesel generator set as approved by The

Engineer

Job 1.00

16100 Construction of RCC f oundation with Anti-vibration pad for

replacement of DG set complete in all respect as approved by The

Engineer

Job 1.00

TOTAL (Rs.)


22/27

Package-4

Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)1 Excavation 1n foundation, for external works

including underground wter tank,manhole,septic

tank,pit,etc disposal of unsuitable/surplus

Material in Common Material consisting of

aelion,residual material consisting of gravel,shale

volcanic ashes,loam,sand,clay or any combination

of these material,altered or weather material and

boulders less than one quarter (1/4) cubic meter

volume emended in other material.

Cu m 120.00

2 v) Earth fil ling, backfil ling with selected

excavated material where available with 95%

(AASHTO) COMPACTION (modified proctor)

includind moistening to optimum moister

content with mechanical means in 6" layers from

the natural ground level/excavated level.in plinth,

Columns footings, wall footings and any other

foundations.

v(a). With selected excavated material where

available with 95% (AASHTO) compaction

(modified proctor) including moistening to

optimum moisture content with mechanical

means in 6" layers from the natural ground

level/excavated level.

Cu m 45.00

3 Lean Concrete (1:4:8) Class 'E' Cyllndrical

Compressive Strength f'c=1500 psi. Cu m 3.00

4 Concrete(1:2:4) Class 'C' Cyl indrical Compressive

Strength f' c= 3000 psi excluding steel and its

bending but including shuttering centering and

its binding as per drawing and specifications

and as directed by Project Manager.

Cu m 12.00

5 Concrete (1:1-1/2:3) Class "B" Cylindrical

Compressive Strenth fc=4000 psi(for U/G Water

Tank) excluding steel and its bending but

including shuttering centring and its binding as

per drawing and specifications and as directed byProject Manager.

Cu m 8.00

6 Concrete (1:1:2) Class "A" Cylindrical Compressive

Strenth fc=4500 psi(for rain water disposal line)

excluding steel and its bending but including

shuttering centring and its binding as per drawing

and specif ications and as directed by Project

Manager.

Cu m 60.00

7 Providing Reinforcement Steel (Grade-60)

including cutting bending placing and binding

wire.

Ton 2.00

AT KM-320

BILL OF QUANTITIES


Bill No. 06D - EXTERNAL WORKS


23/27

8 First Class burnt Brick Masonary work with 1:4

Cement Sand Mortar i/c curing etc complete in all

respect.

Cu m 3.00

9 Fixing and laying of 60mm thick Concrete pavers

including 2" sand bedding over prepared base as

per drawings and specificatoins and as per


Sq m 150.00

10 Plaster,1/2 inchthick 1:3CementSandPlaster on

R.C.C Walls / Ceiling / Slab inclluidig floating coat

unde plaster.

Sq m 50.00

11 Plaster and Sealant Water proofing on inside and

out side of Underground Water Tank by Acrylic

Polymer modified cementitious coating brush

applied trowel finished, three coats,including

10mm white aggregate protection cover layer on

inside and covering slurry plaster outside 2-3mm

of minimum thickness,complete in all respect as

per manufactur's instruction and approved by the

Project Manager.

Sq m 25.00

12 CI Cover for U/G & Over Head Water Tank

Providing and fixing Alass C-250BS EN:124 (70Kg)

CI Cover 18"x18" with T-shape CI frame with fish

tail anchors embedded in slab and locking

arrangment as shown in drawing complete in all

respect as approved by the Engineer.

Nos 2.00

13 R.C.C. Cover for Manhole Providing and fixing

3"(75mm) thick RCC manhole cover ,22" (550mm)

dia, with tee shaped CI frame of 20"(500mm)

clear i/d (frame weighing 40kg) and fish tail

anchors embedded in slab, complete in all

respect as Approved by the Engineer.

Nos 14.00

14 Testing of under ground water storage tank as

per specifications and as directed by Project

Manager.

Nos 1.00

15 Stone Soling

Providing, Laying, compacting and blocking 4"

thick 'Stone soling With 2" down gauge graded

Stone Blast with Stone dust filling and fine sand

aggregates Over prelaid and precompacted fill,

backfill as per specification. (provided for

separately).

Cu m 15.00

Providing and laying R.C.C. pipe, moulded with

cement concrete 1:1-1/2:3 with apigot socket or

collar joint etc including cost of reinforcement

conforming to B.S.S911 Part I:981,Class

"L" including carriage of pipe from factory to site

of work lowering in trenchs to correct alignment

and grade,jointing,cutting pipes where necessary

finshing and testing, etc,complete in all respect as


12" dia Pipe Mtr 170.00

16


24/27

17 Over-burnt Brick GRAVEL Filling in Soakage pit

Providing,Filling Over burnt brick Gravel Filling in

Soakage pit 3" down gauge graded brick gravel as

per specification complete in all respect as


Cu m 14.00

18 Providing and fixing of 3/8"x6" deep continues

ribbed water stopper in UGWT construction joint

as per drawing and specification.Mtr 12.50

TOTAL (Rs.)


25/27

Package-4

Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)

7.1 P/F & Steel H Column, 14"x14"(57 Kg/ft) M.S.Ton 2.47

7.3 P/F & I Purlins "C" Section 150mm x 55mm

channels & runners.Ton 0.41

7.4 P/F & I 1/2 dia M.S bar 2"x2"x1/4" M.S angle

plate 3x40mm 3/16" M.S.cleat plate Ton 51.08

7.5 P/F & I M.S base plate 20mm thick (650mm x

650mm size)Ton 3.96

7.6 P & G Masterflow524 (nonshrinkage material) &

Gasset plate having 650x650mm foundation. No 1.75

7.7 S & C 20guage C.G.I Sheet including 50mm long

Screws with J Bolts.Sq m 582.75

7.11 S&I Cannopy fascia white acrylic sheet Sq m 99.50

7.14 ii. P/F 2'X2' Matel false celling consisting of

gypsum board panels 10-12 mm with Alumunium

lamination / fail on back side and design on the

front i/c cost of framework of tees angles and

4mm hanging G.I wire, including all wastage and

leveling etc, complete in all respect as approved

by the Project Manager.

LM 582.75

7.15 P & F 24 guage M.S sheet welded with top 16

guage MS Sheet of fascia box.

LM 16.97

AT KM-320

BILL OF QUANTITIES

TOTAL (Rs.)


Bill No. 06 E - STRUCTURE STEEL CANOPY & RELATED WORKS


26/27

Package-4Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)

NSI-1P/F of Aluminum Composite Panel on outer side of

boothSM 24.00

NSI-2 P/F of 2 ply Fiber glass on inner side of toll booth. SM 25.00

NSI-3P/F of Insulation Thermo pore 25 kg / cum in

between ms sheet and fiber glass in toll booth.SM 22.00

NSI-4 P/F of False Ceiling 0.6x0.6 side of toll booth. SM 4.00

NSI-5 P/F of Computer and cash table with Lassani(16mm) 3/4" thick SM 1.00

NSI-6P/F of Ventilator of Aluminum Sliding shutter with

grill in Toll BoothSM 0.23

NSI-7 P/F of 50mm Sqr. 16 swg Frame Pipe for toll booth M 93.00

NSI-8P/F of 100 mm with 8.0 mm wall thickness steel

pipe frame for Toll Booth Protection.M 50.00

NSI-9 P/F of Tempered Glass 5mm thick in toll booth SM 7.00

NSI-10P/F of 10" dia Exhaust fan along with closers and fly

netting.

Each 1.00

NSI-11

P/F of Anchor bolts and nuts 16 mm dia 500 mm

long in concrete foundation for booth protection

pipe.

No 16.00

NSI-12P/F of Rawlplug 12.5 mm th. 150 mm long for booth

protection pipe.No 16.00

NSI-13P/F of steel base plate 250 mm dia 16 mm th. for

booth protection pipe.No 4.00

NSI-14P/F of steel base plate 250x250 mm, 16 mm th. for

booth protection pipe.No 4.00

NSI-15 Application of 3 coats Golden yellow, green & brown

colors as per drawing.SM 43.00

NSI-16

P/F of Crest brand LED Slim Panel Lights in False

ceiling (12 Watts of Toll Booth as per approved

drawing.

No 2.00

NSI-17P/F of Door lock of Toll Booth as per approved

drawing.No 1.00

NSI-18

P/F of Complete Wiring with PVC conduit in Booth

for Exhaust fan, two LED Slim lights, and two

sockets, A/C 1.0 ton etc. as per approved drawing.

No 1.00

NSI-19P/F of Circuit breaker as per requirement. as per

approved drawing.No 3.00


AT KM-320

BILL OF QUANTITIES

BILL.NO: 6F :STANDARD TOLL BOOTHS


27/27

NSI-20

P/F of one three pin socket outlet 15/20 amps point

controlled by one switch wiring complete with pvc

single core cable 4 sq. mm in concealed pvc

conduit including earth wire.Circuit breaker as per

requirement. as per approved drawing.

No 3.00

NSI-21 P/F of Power plug along with accessories. No 1.00

NSI-22

P/I of A/C 1.0 ton ACSON / Mitsubishi or Equal of

MS pipe grill fixed for out door unit complete fitting

with all safety measures and necessary welding

bolts and nuts as required, rubber packing and

other materials. Power plug along with accessories.

No 1.00

NSI-23

P/I circuit wiring from DB to Switch board, wiring

with PVC single core cable 2.5 sq. mm +1.5 mm as

ECC in PVC conduit concealed as per site

requirement. of als.Power plug along with

accessories.

M 25.00

NSI-24Providing of Revolving Chair as per Requirement or

as Directed by the engineer No 1.00

TOTAL (Rs.)

Documents

toll-plaza-boq-p-04