Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Contact Area : 30μ'' min.Gold
To:
RJ45 Tab up over USB3.1 Gen1 stack
2017/4/6
Through Hole
Customer P/N:
RUP-ZZ-0062UDE P/N:
10/100/1000 Base-T
RUP17041-00Update Date
A
Approved
Revision
Checked
Spec No.
Prepared
Description:
LED:L-Green/Orange;R-Yellow
Spec No. : RUP17041-00 RUP-ZZ-00621. MECHANICAL DIMENSION
1.1 Product Dimension
www.ude-corp.com
General Tolerance : X.X :X.XX :Unit: mm
- 1 -2017/4/6
± 0.38± 0.20
Spec No. : RUP17041-00 RUP-ZZ-00621.2 Recommended PCB Layout
Component Side of Board
All dimension tolerances are ±0.05mm unless otherwise specified
Table1
X--Forbid; O--OK; NA--Not Applicable.
www.ude-corp.com2017/4/6 - 2 -
Inner layer O
Layout Layer
Bottom side
Trace compo-nent
Groun-ding
Component side X X O X
NA O NA O
O O O O O X O
TestPoint Via Hole PTH NPTH
X O
X O
X
Spec No. : RUP17041-00 RUP-ZZ-00621.3 Recommended Panel Cutout
1.4 Packing Information
40 pcs finished goods per tray
5 trays(200 pcs finished goods) per inner box
4 Inner boxes(800 pcs finished goods) per master carton
www.ude-corp.com2017/4/6 - 3 -
Spec No. : RUP17041-00 RUP-ZZ-00621.5
- All dimensions follow :
FCC subpart F, 68,500, Figure (C)(2)(i) & (C)(2)(ii) & (C)(3)(i)
IEC 60603-7
- All plugs must be meeting the requirements of plug Go & No-Go gauge.
Gauge follow : FCC subpart F, 68,500, Figure (C)(4)(i) & (C)(5)(i)
- There must be no damage to Housing and Locking Latch.
- There must be no nicks and cuts in cable.
- Durability : 750 cycles generally
www.ude-corp.com- 4 -
Standard RJ45 Plug Specification
2017/4/6
Spec No. : RUP17041-00 RUP-ZZ-00621.6
www.ude-corp.com
- All dimensions follow : Universal Serial Bus 3.0 Specification, Revision 1.0. Figure 5-2. USB 3.0 Standard Plug-A interface dimensions - Non-dimensions geometry for reference only, subjece to change. - Drawing for mating interface dimensions only. Views may not show realistic manufacturing condition.
2017/4/6 - 5 -
Standard USB 3.0 Plug Specification
Spec No. : RUP17041-00 RUP-ZZ-00622. REQUIREMENTS
2.1 Design and Construction
2.2 Material2.2.1 Terminal Parts (Underplating : 50μ" min. Nickel overall)
2.2.1.1 RJ Terminal : Phosphor Bronze, Thickness=0.30mmFinish : Contact Area : 30μ" min. Gold Solder Tail : 100μ" min. Matte Tin
2.2.1.2 USB 2.0 Terminal :Phosphor Bronze, Thickness=0.25mmFinish : Contact Area : 30μ" min. Gold Solder Tail : 100μ" min. Matte Tin
2.2.1.3 USB 3.1 Terminal : Brass, Thickness=0.25mmFinish : Contact Area : 30μ" min. Gold Solder Tail : 100μ" min. Matte Tin
2.2.1.4 Input Terminal : Brass, Thickness=0.35mmFinish : 100μ" min. Matte Tin
2.2.1.5 Case Terminal : CP Wire, Diameter=0.40mmFinish : 100μ" min. Matte Tin
2.2.1.6 LED Terminal : Brass, Thickness=0.35mmFinish : 100μ" min. Matte Tin
2.2.2 Plastic Parts <UL94V-0>2.2.2.1 RJ Housing : PBT, Black 2.2.2.2 Spacer : PBT, Black 2.2.2.3 Case : PF2A5-151J,Black 2.2.2.4 USB Housing : PA9T, Blue(300C)2.2.2.5 USB Back Cover : PA9T, Blue(300C)
2.2.3 Shield Parts2.2.3.1 Front Shield : Stainless Steel, Thickness=0.25mm, unplating2.2.3.2 Back Shield : Stainless Steel, Thickness=0.20mm, Pre-soldering
www.ude-corp.com
Product shall be of design, construction and physical dimensions specifiedon applicable.
- 6 -2017/4/6
Spec No. : RUP17041-00 RUP-ZZ-00622.3 Operating and Storage Temperature
2.4 RJ45 specifications
Insertion force with the latch depressed :
2.5 USB 3.1 specifications
1A
30mΩ Max.
500Vac @1min
2.6 Performance and Test Description
2.7 Packaging and Packing
www.ude-corp.com
10 N min and 8 N after the specified insertion/extraction
500MΩ min.
0°C to +70°C
Insulation Resistance :
20N max.
- 7 -2017/4/6
All parts shall be packaged and packed to protect against physicaldamage、corrosion and deterioration during shipment and storage.
Extraction force :
Durability :
Locking Force of Plug Latch :
Insertion force :
Storage Temperature :
Durability : 1500 cycles for standard class
20N max.
Operating Temperature :
Contact Resistance:
2500 cycles
50N min. @ 60+/-5 sec
Contact Current Rating:
1000MΩ min.
Product is designed to meet electrical, mechanical and environmentalperformance requirements specified in below table. All tests are performedat ambient environmental conditions per MIL-STD-1344A and EIA-364unless otherwise specified.
-40°C to +85°C
35 N max at a max. rate of 12.5mm per minute
Removal force with the latch depressed :
Insulation Resistance :
Dielectric Withstanding Voltage :
Spec No. : RUP17041-00 RUP-ZZ-00623. ELECTRICAL CHARACTERISTICS @ 25℃
3.1 Schematic
www.ude-corp.com
10μA max.
2017/4/6 - 8 -
Yellow 588 1.7 ~2.6 V
570Ir @Vr=5V
1.7 ~2.6 V 10μA max.10μA max.
605
λp (nm) Vf @If=20mA1.7 ~2.6 V
Emitting ColorGreen
Orange
VCC R1
TD1+ R2
TD1- R3
TD2+ R4
TD2- R5
TD3+ R6
TD3- R7
TD4+ R8
TD4- R9
GND R10
C1 TX1+
C2 TX1-
C3 TX2+
C6 TX2-
C4 TX3+
C5 TX3-
C7 TX4+
C8 TX4-
1:1
1:1
1:1
1:1
75Ω
75Ω
75Ω
75Ω
0.1uF
0.1uF
0.1uF
0.1uF
PHY Side(Input) Cable Side
(RJ45 Output)
2KV,1000pF
Shield
L1
Yellow
L2
L3
L4
OrangeGreen
Spec No. : RUP17041-00 RUP-ZZ-00623.2 Transmitter filter & Receiver filter
Type : Balance low pass 100Ω impedance
Insertion loss :
Return loss :
3.3 Common Mode Rejection
@ 1~100 MHz -30dB min.
3.4 Cross Talk
@ 1~100 MHz -30dB min.
3.5 Inductance @ 100KHz, 0.1V, 8mA DC BIAS
Input (R2-R3), Input(R4-R5), Input (R6-R7), Input(R8-R9): 350 μH min.
3.6 HiPot Test
Input(R2-R3) To 1500Vac 60s or 2250Vdc 60s
Input(R4-R5) To 1500Vac 60s or 2250Vdc 60s
Input(R6-R7) To 1500Vac 60s or 2250Vdc 60s
Input(R8-R9) To 1500Vac 60s or 2250Vdc 60s
www.ude-corp.com
Output(C7-C8) :
load 100Ω
load 100Ω
load 100Ω-16dB min.30~60MHz
60~80MHz -12dB min.
-10dB min.
- 9 -
Output(C1-C2) :
Output(C4-C5) :
80~100MHz
Output(C3-C6) :
2017/4/6
1~100 MHz -1.0dB max.
1~30 MHz -18dB min. load 100Ω
Spec No. : RUP17041-00 RUP-ZZ-00624. DIPPING TEMPERATURE PROFILE
www.ude-corp.com- 10 -2017/4/6
Spec No. : RUP17041-00 RUP-ZZ-00625. Revision History
www.ude-corp.com
A Initial Release . Soil
Operator
2017/4/6 - 11 -
Issue Date Revision Comments
2017/4/6