GSM/GPRS/GPS TRACKER

MANUAL

Preface

Thank you for purchasing the tracker. This manual shows how to operate the devicesmoothly and correctly. Make sure to read this manual carefully before using thisproduct. Please note that specification and information are subject to changes withoutprior notice in this manual. Any change will be integrated in the latest release. Themanufacturer assumes no responsibility for any errors or omissions in this document.

1．SummaryWorking Based on existing GSM/GPRS network and GPS satellites, this product can

locate and monitor any remote targets by SMS or internet.

第 1 页

2．Introduction

3． LED Indication 3.1 Red LED（GSM signal indicator） Status Meaning

Slow flasing GPS signal has been acquired successfullyQuickly flashing GSM signal was searching Continuously in dark Power off or the gps was sleeping

3.2 Blue LED (GPS signal indicator）

第 2 页

Status MeaningSlow flashing GPS signal has been acquired successfullyLong bright GPS signal was searching Continuously in dark GPS stops working/ the gps was sleeping

4. Wiring

5. PlacementThe terminal should be placed under cover. It is recommended to ask professionalcompanyes to install the terminal for you

6.SIM card installation6.3.1 Make sure the Simcard is 2G and open GPRS function6.3.2 Make sure that there is no call transfer and call display is on, and PIN code off.

第 3 页

The SMS message must in Text format, can’t be identified for PDU format.

7.parameter

Name ParameterDimensions 97mm * 57mm * 19mmCommunicationnetwork

GSM/GPRS

GSM frequency GSM 850/900/1800/1900 MHzGPS chip G-TOPGSM chip MTKGPS sensitivity -159dBmGPS positioningaccuracy

5-30m

Voltage DC 12~36VCurrent <80mAStandby current <10mAStorageTemperature

-40°C to +85°C

Operatingtemperature

-20°C to +65°C

Humidity 5%--95% non-condensing

8.Operating Instructions （default password is 0000.）

8.1 Set up the administrator

the command SMS: #710#phone number# pass word##For example：#710#13588888888#0000##When you sending successfully, all the alarm messages will be send to adminstratornumber .

8.2 Change the Password

The command SMS: #770#new password#User password##When you sending successfully, it will reply “770CONFIG OK” when the pass word iswrong; it will reply “770PASSWORD ER”If you fogot the password you can sending the command SMS:#901##

8.3 Read the parameter

The command SMS: #901##

第 4 页

When you sending successfully you will get the sms include the administrator number、password and the IMEI.

8.4 The interval of gps data

The command SMS: # 730# time # data groups # User password ##For example: #730#20#2#0000##When you sending successfully ,the terminal will stored the gps data every 20seconds,when the data groups amounts to the 2times, that will send out to the server

8.5 Set up the APN

The command SMS: #802#apn #apn user name#apn password# User password ##example 1: the APN is internet, not user name and passwored Command: #802#internet###0000##example 2: the APN is internet , the APN user name:guet passwrod:a1234Command: #802#internet#guest#a1234#0000##When you sending successfully, it will reply “802CONFIG OK” when the pass word iswrong; it will reply “802PASSWORD ER”

Note: The default APN is CMNET.

8.6 Geo-fence alarm

The command SMS: # 751 # fence radius # sampling interval # longitude #latitude # user password ##For example: #751#500#5#22.5442N#113.91E#0000##After the setup is successful, the setting mobile phone will receive a piece of config okcommand. Then, when the ward leaves this area, the terminal will send the alarminginformation of being out of the fence to the center number. The alarm sms is :

#354923033045862##0#000#OUT#1#v#113.3454E52.67850000.##Note: Send 9860000 reply of longitude and latitude this standard

8.7 Reading Geo-fence information

The command SMS: # 752 # user password ## When you sending successfully, the terminal will read the data of the module fenceworking status and return message to the sending mobile phone. For example: #752#0000##Return: #open:1#lat:11456.209400#lng:2233.470100#distance:500#time:5#status:2Where, open: 1 indicates fence open; Open: 0 indicates fence closed; lat:11456.209400, latitude; lng: 2233.470100; longitude; distance: 500; fence radius; time: 5 sampling interval; status: 2 , terminal has obtained valid satellite data, fence works normally; status: 1; fence open, but there are no valid satellite data have been received; status: 0, no electronic fence is set.

8.8 close the Geo-fence

The command SMS: #760 # user password ##

第 5 页

Example: #760#0000##When you sending successfully, it will reply “760CONFIG OK”, all the Geo-fencewill be cancelled. when the pass word is wrong; it will reply “760PASSWORD ER”

8.9 Alarm format

Send command:#720#Warning way1-2#User password##1. Warning way1：Dial-up alarm2. Warning way2：Message alarm （default）When you sending successfully, it will reply “720CONFIG OK”

8.10 Cable cut-off Alarm

When the terminal cable is cut off, the cable cut-off alarm will be activated. Theterminal will send the alarm to the adminstrator , the SMS alarm: power was cut off !

9.Control circuit:

9.1 Fuel cut

The command: 222+password Example: 2220000When you sending successfully,the terminal will reply the SMS to you : RF2 OK. Thenthe device will be cut off the fuel.

9.2 Resume supporting the fuel

The command: 232+password Example: 2320000 When you sending successfully,the terminal will reply the SMS to you : RF2 OFF. Thenthe device will was supply the fuel .

10 Real time tracking10.1 SMS tracking (1)666+userpasswordExample:6660000.Send this SMS command to the terminal, it will reply latest longitude and latitudeinformation.(2)986+userpasswordExample:9860000. Send this SMS command to the terminal, it will reply the Google maps linkIf GPS is not located at all, the terminal will reply: 34592303105400 Can not get a valid location!

10.2 Real time tracking ( platform server)The terminal will send position information to the platform server timely. Users can

check the position on the platform.

第 6 页