Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
TOOLING IDENTIFICATION AND POSITIONING SYSTEMŽ
TIPS
ww
w.w
ila.n
lG
BGB
TIPS
TOOLING IDENTIFICATION AND POSITIONING SYSTEMžWILA’s core activities are aimed at a single mission: To achieve the highest level of productivity for the
press brake user. To achieve this, WILA continuously strives to develop the latest bending technologies and
innovations, resulting in high quality products. The TIPS system is one of the most recent WILA innovations.
The WILA TIPS system is an integrated part of the press brake control system and supports tooling identification and continuous monitoring of
tooling position. In any position in an upper clamping, lower clamping or storage system, tooling can be located and identified. Due to the very
precise recognition of the tools, the TIPS system indicates if the correct tool is being used, if the length of the tool is correct, and what should be
the exact position of the tool in the clamping system. With this detailed information both errors and test bends can be avoided, resulting in a
substantial increase in productivity.
www.wila.nl sales: +31 (0)573 28 98 50
TIPS TOOLING (A)Each New Standardž Premium (special) tool can be equipped with
a TIPS ID-tag (A1). The ID-tag holds an unique serial number which
represents tool specific information (e.g. tooling length, type, max load,
etc.) which is necessary to identify each tool.
Tool with TIPS
TIPS ID-tag
A1
B
C
D
TIPS interconnect board
TIPS communication board
TIPS ID-tag
Press Brake IPC
OEM
WILA
TIPS DIN controller
DIN Power Supply
Clamping System with TIPSTIPS toolA
A1
TIPS Clamping SystemB
DETAIL B SCALE 2 : 1
TIPS ID-tagTIPS toolA
A1
TIPS Clamping SystemB
DETAIL B SCALE 2 : 1
TIPS ID-tag
www.wila.nl sales: +31 (0)573 28 98 50
CUSTOM TIPS CONTROLLER (C)The TIPS DIN controller (C1) module is the center of the TIPS system.
The TIPS DIN Controller is connected to the press brake IPC (D). With
the CAN or Ethernet interface it receives commands from the press
brake IPC and controls the identification and positioning process.
A complex algorithm calculates the tool position from the electrical
field which is read from the clamping system. Commands can be
sent and requested using CAN messages (CAN interface) or TCP/IP
messages (Ethernet interface). In this way, by supporting multiple
interfaces, the TIPS system can be easiliy accessed. Furthermore,
CAN routing supports multiple active channels, therefore multipe
TIPS and even WILA Smart Tool Locator function next to each other!
IPC INTEGRATION (D)The communication between the IPC (D) and the TIPS controller (C) is
based on the IPC making commands to the TIPS controller to make a
scan of the complete system. After this command, the TIPS system will
do a complete scan, and the scan results can be retrieved by the
IPC(identification and position of all tooling in the system). In the IPC
the information is processed and used in several ways. For example to
check the tooling setup.
An important aspect is that the integration of our TIPS system in the
IPC is not part of the TIPS solution. This has to be prepared by the IPC
manufacturer (see blue line).
TIPS CLAMPING SYSTEM (B)Any New Standardž Premium automatic clamping system can be
equipped with the TIPS system up to 4590 mm length.
TIPS electronic communication boards are fitted in the complete
length of the clamping system. By means of a continuously changing
electric field, the TIPS system is able to power the ID-tag and receive
messages. Each TIPS Clamping System is connected to the TIPS DIN
Clamping Switch by a cable.
Tool with TIPS
TIPS ID-tag
A1
B
C
D
TIPS interconnect board
TIPS communication board
TIPS ID-tag
Press Brake IPC
OEM
WILA
TIPS DIN controller
DIN Power Supply
Clamping System with TIPS
ww
w.w
ila.n
l
WILA B.V.
P.O. box 60
NL-7240 AB Lochem
The Netherlands
Phone +31 (0)573 28 98 00
Phone sales +31 (0)573 28 98 50
E-mail: [email protected]
www.wila.nl
PRESS BRAKE PRODUCTIVITY CATALOG
Request a copy of the Press Brake Productivity Catalog
at www.wila.nl
GBG
B
WILA. THE PRESS BRAKE PRODUCTIVITY PEOPLE.
WILA is totally focused on providing a line of products and support
systems to maximize the productivity of your press brakes. For over 80
years, WILA has specialized in Clamping Systems, Crowning Systems and
Tooling and Accessories to reduce set-up time and improve accuracy of
the press brake. Through strong partnerships with the world’s leading
press brake manufacturers, an extensive and trained dealer network, long
experienced regional managers, dedicated application support and
engineering staff, WILA is always close at hand to support your needs.