Tiger Controls Equipment Co.,Ltd. - TL..-..BC-S.12 Series 2-port / 3 … · 2015. 3. 25. · Tiger Controls Equipment Co., Ltd Tel: 0086-429-6879888 Fax: 0086-429-6796222 Http:

Tiger Controls Equipment Co., Ltd

Tel: 0086-429-6879888 Fax: 0086-429-6796222 Http:// www.tiger-control.com Email: [email protected]

2-port / 3-port ValvesFemale Threaded,PN16/PN25

TL..-..BC-S.12 Series

Valve body material: stainless steel

DN15...DN80 （chilled/hot water） DN15...DN50(steam)

Kvs:1.9...66m3/h

Standard of female threaded connection: ISO 7/1

Can be fitted with electric actuators: TC/TR...-D..-.12 ，TC/TR...-X..-.12

1

This kind of valve body is suitable for HVAC system, air conditioning, and refrigeration system.

Chilled water

Anti-freeze water

Refrigerant

（R12、R22、R134a、R202）

Glycol

Hydrazine

Phosphate

Low temperature hot water

High temperature hot water

Saturated steam(≤150℃ or ≤0.1MPa)

Saturated steam(≤0.69MPa)

Overheated steam(≤180℃)

Note: when medium temperature in valve is below 0℃ (R12, R22, R134a, R202, glycol), the stem of the valve should

be protected by electric heating cover(Type: THOT-1) to avoid frosting and icing.

-25℃~150℃

(Chilled/hot water valve)

2℃~180℃

(Steam valve)

Application

Datasheet No.:

TL-01

Type2-port

Type 3-port

Caliber(in.)

DN(mm)

Kvs(m3/h)

Stroke(mm)

ActuatorRecommended

2-port △pmax (Mpa)

3-port △pmax (Mpa)

TL15-2VBC-S.12 TL15-3VBC-S.12 1/2" 15 1.9 10 500N ≤1.60 ≤0.50TL20-2VBC-S.12 TL20-3VBC-S.12 3/4" 20 4.4 10 500N ≤1.10 ≤0.50TL25-2VBC-S.12 TL25-3VBC-S.12 1" 25 8 15 500N ≤0.70 ≤0.40TL32-2VBC-S.12 TL32-3VBC-S.12 1-1/4" 32 10 20 500N ≤0.40 ≤0.35TL40-2VBC-S.12 TL40-3VBC-S.12 1-1/2" 40 20 20 500N ≤0.25 ≤0.30TL50-2VBC-S.12 TL50-3VBC-S.12 2" 50 32 20 1000N ≤0.30 ≤0.30TL65-2VBC-S.12 TL65-3VBC-S.12 2-1/2" 65 50 20 1000N ≤1.60 ≤0.25TL80-2VBC-S.12 TL80-3VBC-S.12 3" 80 66 20 1000N ≤1.60 ≤0.25Note:(3-port female threaded stainless valve)DN15~DN80 3-port valve are all mixing , if you need diverting ones, please exchange A and AB according to plate on the valve.

Type Summary

Chilled/hotwater valves

(-25...+150℃)

Steam valves

(2...+180℃)

Actuator Overview

Valve Flow Characteristic

Type

2-portCaliber

(in.)DN

(mm)Kvs

(m3/h)Stroke(mm)

ActuatorRecommended

△pmax (Mpa)

TL15-2SBC-S.12 1/2" 15 1.9 10 500N ≤1.60TL20-2SBC-S.12 3/4" 20 4.4 10 500N ≤1.10TL25-2SBC-S.12 1" 25 8 15 1000N ≤1.20TL32-2SBC-S.12 1-1/4" 32 10 20 1000N ≤0.80TL40-2SBC-S.12 1-1/2" 40 20 20 1800N ≤1.20TL50-2SBC-S.12 2" 50 32 20 1800N ≤0.75

Notes: DN= Nominal diameterKvs= Nominal flow coefficient, which refer to the flow when medium (Density=1g/cm3) go through the full open control valve, whose differential pressure at two ends of valve is 0.1Mpa.Type instruction:e.g.TL**-2VBC-S.121. L: Female threaded2. **: Caliber3. Medium: V: water -25℃~150℃; S: steam 2~180℃4. Valve Body: B: stainless steel5. Pressure: C: PN16 D: PN256. .12: Tiger Controls' standard interface

Type Rating Force

Actual ForceOperatingVoltage

Control Signal Manual Running speed

TC500-X24-S.12 500N 500N~700N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.85s/mm (50Hz)TC500-D24-S.12 500N 500N~700N 24VAC 3-position Yes 3.85s/mm (50Hz)TC1000-X24-S.12 1000N 1000N~1200N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.85s/mm (50Hz)TC1000-D24-S.12 1000N 1000N~1200N 24VAC 3-position Yes 3.85s/mm (50Hz)TR1800-X24-S.12 1800N 1800N~2000N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.13s/mm (50Hz)TR1800-D24-S.12 1800N 1800N~2000N 24VAC 3-position Yes 3.13s/mm (50Hz)TR3000-X24-S.12 3000N 3000N~3500N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.13s/mm (50Hz)TR3000-D24-S.12 3000N 3000N~3500N 24VAC 3-position Yes 3.13s/mm (50Hz)Notes: 1. Operating voltage is available for 220V/24VAC, which must be noted when ordering, the type should be changed from "24" to "220". For example, change "TC500-X24-S.12" to "TC500-X220-S.12". 2. 10K feedback function can be selected when actuator is 3-position type, which must be noted when ordering, the type should be changed from"S" to "SF10K". For example, change "TC500-X24-S.12" to "TC500-X24-SF10K.12". 3. SPDT feedback function also can be selected when actuator is 3-position type, which must be noted when ordering, the type should be changed from"S" to "SF2". For example, change "TC500-X24-S.12" to "TC500-X24-SF2.12". 4. S means manual function.5. The actual running time depends on the actual valve stroke.

2Tiger Controls Equipment Co., Ltd


medium flow100%

control signal 100%

equal-linear curve

medium flow100%

control signal 100%

equal-percentage curve

The valve and actuator can be easily assembled without special tool and adjustment. See specification for installation details.

3

Machanical DesignFlow direction of medium

Medium flow relationship

Mounting with actuator

Mounting with pipe

Plate on the valve

Flow direction:valve stem retracts:valve stem extends:

A to ABflow increasesflow decreases

A,B to ABflow of A increases, B decreasesflow of A decreases, B increases

AB to A,Bflow of A increases, B decreasesflow of A decreases, B increases

2-port 3-port mixing 3-port diverting DN15~DN80 DN15~DN80 DN15~DN80

2-port 3-port mixing 3-port diverting DN15~DN80 DN15~DN80 DN15~DN80

2. Valve can be installed in the water supply pipe or return water pipe (priority selection). Besides, filter and check valve are recommended to be installed. When the medium is steam, install draw off valve in the pipe can remove the condensed water, or it will effect the life of valve.



Kvs

△P: Differential pressure when control valve is full open (unit: kPa)

V: Rating flow at the △P (unit: m3/h)

Kvs = Nominal flow coefficient, which refer to the flow when medium (Density=1g/cm3) go through the full open

control valve, whose differential pressure at two ends of valve is 0.1Mpa.

Relationship between Differential Pressure and Flow

1.valve should be installed according to marked direction.

2-port 3-port diverting valve 3-port diverting valve DN15~DN80 DN15~DN80 DN15~DN80

Note: The 2-port valve closes when the stem extends.

MountingOrientation

Commissioning

Maintenance

Technical Data

Operating Data

Material

4

Commission the valve only if the actuator has been mounted correctly.

Permissible Pressure

Standard of female threaded

connection

Leakage rate

Permissible media

Water valve

（-25℃~150℃）

Steam valve

（2℃~+180℃）

Permissible pressure

Stroke

Valve body

Valve core

Stem

Seal ring

Sealing structure

PN16

ISO 7/1

0.02% Kvs

Chilled water, Anti-freeze water, Refrigerant(R12、R22、R134a、

R202),Glycol, Hydrazine, Phosphate, Low and high temperature hot

water, Saturated steam（≤150℃ or ≤0.1MPa）

Saturated steam(≤0.69MPa), Overheated steam(≤180℃)

1.6Mpa(1600Kpa, 16bar)

10mm(DN15-DN20),15mm(DN25),20mm(DN32-DN80)

Stainless steel

Stainless steel

Stainless steel

Teflon

V model sealing gland + stainless steel spring auto-compensation

Medium is chilled/hot water Medium is steam

Downward installation is forbidden Any installation position is OK

When doing service work on the valve / actuator:

1. Close the pump and turn off the power supply.

2. Close the shut-off valve, exhaust water in the pipe to reduce the pressure inside pipes. Make water

pipe(hot water) cool down naturally.

3. Dismantle electric wires from wiring terminals.

Notice:When we do the pipe pressure testing and flshing,the valve body should be in a state of full open.

This operation can not only protect the internal parts of valve body, but also prevent pipe from blocking.



refer to <Dimensions>

refer to <Dimensions>

Dimension

Weight

Dimension/Weight

Dimension Figure

2-port

3-port

Type 2-port

Type 3-port DN L1

mm2-port L3

mm3-port L3’

mm H1mm

H2mm

Hmm

(500N/1000N)

2-port weight

Kg

3-port weight

Kg

TL15-2VBC-S.12 TL15-3VBC-S.12 15 80 38 49 18 95 248 1 0.8

TL20-2VBC-S.12 TL20-3VBC-S.12 20 80 40 51 21 98 251 1.1 1.1

TL25-2VBC-S.12 TL25-3VBC-S.12 25 100 44 55 24 101 254 1.5 1.6

TL32-2VBC-S.12 TL32-3VBC-S.12 32 103 47 62 30 107 260 1.8 1.8

TL40-2VBC-S.12 TL40-3VBC-S.12 40 122 52 71 36 113 266 2.3 2.3

TL50-2VBC-S.12 TL50-3VBC-S.12 50 138 65 85 41 118 271 3.4 3.3

TL65-2VBC-S.12 TL65-3VBC-S.12 65 160 77 100 51 128 281 5.2 6.0

TL80-2VBC-S.12 TL80-3VBC-S.12 80 180 87 115 58 135 288 6.8 7.1

Remark:1.The weight of the steam valve is the same as the water valve.

5Tiger Controls Equipment Co., Ltd


6

BAS valve bodySeries TC500... TC1000... TR1800...

Nominal stroke 22mm 22mm 44mm

Nominal output force 500N 1000N 1800N

Basic application Type

● HVAC TC500.../ TC1000...

TR1800.../ TR3000...

3-position, 24VAC 3-position TC500-D24-S.12 TC1000-D24-S.12 TR1800-D24-S.12

proportional, 24VAC 0(2)...10VDC , 0(4)...20mA TC500-X24-S.12 TC1000-X24-S.12 TR1800-X24-S.12

3-position, 220VAC 3-position TC500-D220-S.12 TC1000-D220-S.12 TR1800-D220-S.12

proportional, 220VAC 0(2)...10V,DC 0(4)...20mA

TC500-X220-S.12 TC1000-X220-S.12 TR1800-X220-S.12

3-position,10K resistance(24VAC / 220VAC) 3-position TC500-D24-SF10K.12/

TC500-D220-SF10K.12TC1000-D24-SF10K.12/TC1000-D220-SF10K.12

TR1800-D24-SF10K.12/TR1800-D220-SF10K.12

3 position,2 SPDT feedback(24VAC /220VAC) 3-position TC500-D24-SF2.12/

TC500-D220-SF2.12TC1000-D24-SF2.12/TC1000-D220-SF2.12

TR1800-D24-SF2.12/TR1800-D220-SF2.12

Valve body Type DN StrokeFlow

paremeter Kvs

△Ps △Ps △Ps

[mm] [mm] [m3/h] [MPa] [MPa] [MPa]

PN

16, medium

temperature -25 ℃

~ 150℃

Female threaded water

valve

TL15-2VBC-S.12 DN15 10 1.9 1.60

TL20-2VBC-S.12 DN20 10 4.4 1.10

TL25-2VBC-S.12 DN25 15 8 0.70

TL32-2VBC-S.12 DN32 20 10 0.40

TL40-2VBC-S.12 DN40 20 20 0.25

TL50-2VBC-S.12 DN50 20 32 0.30 0.60

TL65-2VBC-S.12 DN65 20 50 1.60 1.60

TL80-2VBC-S.12 DN80 20 66 1.60 1.60

2 ℃ ~ 180

℃

Female threaded steam

valve

TL15-2SBC-S.12 DN15 10 1.9 1.60

TL20-2SBC-S.12 DN20 10 4.4 1.10

TL25-2SBC-S.12 DN25 15 8 1.20

TL32-2SBC-S.12 DN32 20 10 0.80

TL40-2SBC-S.12 DN40 20 20 1.20

TL50-2SBC-S.12 DN50 20 32 0.75

PN

16,medium

temperature,-25

℃ ~ 150

℃

Female threaded water

valve

TL15-3VBC-S.12 DN15 10 1.9 0.50

TL20-3VBC-S.12 DN20 10 4.4 0.50

TL25-3VBC-S.12 DN25 15 8 0.40

TL32-3VBC-S.12 DN32 20 10 0.35

TL40-3VBC-S.12 DN40 20 20 0.30

TL50-3VBC-S.12 DN50 20 32 0.30 0.60

TL65-3VBC-S.12 DN65 20 50 0.25 0.50

TL80-3VBC-S.12 DN80 20 66 0.25 0.50

Notes:1.Kvs calculating software: log in website---www.tiger-control.com for online version. Download versions for Android and Apple users are available.2.PN25 is avaliable, please change the type from "C" to "D" when you place an order. eg: TF150-2VGD-S.12.3.Please choose accessory: THOT-1 heating cover to protect the valve stem from freezing if the meduim is glycol or other low-temperature medium.4.If the steam valves need Fail-safe function, please add accessory---TUPS-24 (Uninterruptible Power Supply). TUPS-24 will provide the control signal to shut off the valve when power fails in the system. For more information, please refer to the technical literature on website www.tiger-control.com or ask local agents for help.



2-port / 3-port valvesFlanged,PN16/PN25/PN40

TF...-..GC-S.12 Series

Valve body material: ductile iron

DN15...DN400

Kvs:2...2200m3/h

Below DN80 of 3-port valve, the valve core only mixing type (reversal when diverting occasion)

Above DN80 of 3-port valve, the valve core have both mixing type and diverting type

Standard of flanged connection: ISO 7005-2

Can be fitted with electric actuators: TC/TR...-D.-.12, TC/TR...-X..-.12

7

This kind of valve body is suitable for HVAC system, air conditioning, and refrigeration system.

Chilled water

Anti-freeze water

Refrigerant

（R12、R22、R134a、R202）

Glycol

Hydrazine

Phosphate

Low temperature hot water

High temperature hot water

Saturated steam(≤150℃ or ≤0.1MPa)

Saturated steam(≤0.89MPa)

Overheated steam(≤180℃)

High-temperature steam(≤200℃)

Super-High-temperature steam(≤450℃)

Notes: when medium temperature in valve below 0℃ (R12, R22, R134a, R202, glycol), the stem of the valve should be protected by electric heating cover(Type: THOT-1) to avoid frosting and icing.

-25℃~150℃

(Chilled/hot water

valve) 2℃~180℃

(Steam valve)

Application

Medium

Datasheet No.:

TF-01

2℃~220℃

(High-Temp.

Steam valve)

2℃~450℃

(Super-High-Temp.

Steam valve)



Type2-port

Type 3-port

Caliber(in.)

DN(mm)

Kvs(m3/h)

Stroke(mm)

ActuatorRecommended

2-port△pmax (Mpa)

3-port△pmax (Mpa)

TF15-2VGC-S.12 TF15-3VGC-S.12 1/2" 15 2 20 500N ≤1.60 ≤0.80TF20-2VGC-S.12 TF20-3VGC-S.12 3/4" 20 3 20 500N ≤1.10 ≤0.80TF25-2VGC-S.12 TF25-3VGC-S.12 1" 25 5 20 500N ≤0.70 ≤0.80TF32-2VGC-S.12 TF32-3VGC-S.12 1 1/4" 32 8 20 500N ≤0.40 ≤0.80TF40-2VGC-S.12 TF40-3VGC-S.12 1 1/2" 40 20 20 500N ≤0.25 ≤0.80TF50-2VGC-S.12 TF50-3VGC-S.12 2" 50 31 20 1000N ≤0.30 ≤0.30TF65-2VGC-S.12 TF65-3VGC-S.12 2 1/2" 65 50 20 1800N ≤0.45 ≤0.45

TF80-2VGC-S.12 TF80-3VGC-HS.12TF80-3VGC-FS.12 3" 80 80 20 1800N ≤0.30 ≤0.27






TF300-2VGC-Y.12 TF300-3VGC-HY.12TF300-3VGC-FY.12 12" 300 1200 100 16000N ≤1.60 ≤0.25



Notes: (3-port ductile iron flanged valve)

1. DN15~DN65 3-port valve are all mixing, if you need diverting ones, please exchange A and AB according to plate on the valve.2. DN80~DN400, the valve core have both mixing type and diverting type. Please note it when ordering, "HS" means mixing, "FS" means diverting.3. Attention: DN80~DN400 medium flow relationship are opposite between mixing and diverting valve.

Type Summary

Chilled/hotwater valves

(-25...+150℃)

Steam valves

(2...+180℃)

8

Type2-port

Caliber(in.)

DN(mm)

Kvs(m3/h)

Stroke(mm)

ActuatorRecommended

2-port△Ps(Mpa)

TF15-2SGC-S.12 1/2" 15 2 20 1800N ≤1.60TF20-2SGC-S.12 3/4" 20 3 20 1800N ≤1.60TF25-2SGC-S.12 1" 25 5 20 1800N ≤1.60TF32-2SGC-S.12 1 1/4" 32 8 20 1800N ≤1.60TF40-2SGC-S.12 1 1/2" 40 20 20 1800N ≤1.60TF50-2SGC-S.12 2" 50 31 20 1800N ≤1.60TF65-2SGC-S.12 2 1/2" 65 50 20 1800N ≤1.60TF80-2SGC-S.12 3" 80 80 20 1800N ≤1.60TF100-2SGC-S.12 4' 100 125 40 3000N ≤1.60TF125-2SGC-S.12 5" 125 200 40 3000N ≤1.60TF150-2SGC-S.12 6" 150 300 40 3000N ≤1.60TF200-2SGC-S.12 8" 200 520 40 5000N ≤1.60TF250-2SGC-S.12 10" 250 750 40 5000N ≤1.60TF300-2SGC-Y.12 12" 300 1200 100 16000N ≤1.60TF350-2SGC-Y.12 14" 350 1800 100 16000N ≤1.60TF400-2SGC-Y.12 16" 400 2200 100 16000N ≤1.60

Note:1.If medium temperature is low,pls select accessory:THOT-1 electric heating cover to protect valve stem from freezing2. If power reset function is needed for steam valve, pls select TUPS-24, it can provide control signal for valve closing when the system is power off.3. PN25 valve is selectable, just change the type from C to D,e.g. TF150-2VGD-S.124. 450℃ super high temperature valve is selectable, caliber:DN15~DN400 e.g.:2 port DN150 super high temperature valve type: TF150-2PGC-S.12

Type Instruction: eg: TF**-2VGC-S.121. F: Flanged2. **: Caliber3. Medium: V: water -25℃~150℃ S: steam 2℃~180℃ A: high-temp. steam 2℃~220℃ P: super-high-temp. steam 2℃~450℃4. Valve Body: G: ductile iron5. Pressure: C: PN16; D: PN256. .12: Tiger Controls' standard interface



Kvs

△P: Differential pressure when control valve is full open (unit: kPa)

V: Rating flow at the △P (unit: m3/h)

Kvs = Nominal flow coefficient, which refer to the flow when medium (Density=1g/cm3) go through the full open control valve,

whose differential pressure at two ends of valve is 0.1Mpa.

9

medium flow100%

control signal 100%

equal-linear curve

medium flow100%

control signal 100%

equal-percentage curve

Valve Flow Characteristic

Type Rating Force

Actual ForceOperatingVoltage

Control Signal Manual Running speed

TC500-X24-S.12 500N 500N~700N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.85s/mm (50Hz)TC500-D24-S.12 500N 500N~700N 24VAC 3-position Yes 3.85s/mm (50Hz)TC1000-X24-S.12 1000N 1000N~1200N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.85s/mm (50Hz)TC1000-D24-S.12 1000N 1000N~1200N 24VAC 3-position Yes 3.85s/mm (50Hz)TR1800-X24-S.12 1800N 1800N~2000N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.13s/mm (50Hz)TR1800-D24-S.12 1800N 1800N~2000N 24VAC 3-position Yes 3.13s/mm (50Hz)TR3000-X24-S.12 3000N 3000N~3500N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.13s/mm (50Hz)TR3000-D24-S.12 3000N 3000N~3500N 24VAC 3-position Yes 3.13s/mm (50Hz)TR5000-X24-S.12 5000N 4500N~5500N 24VAC 0(2)~10V, 0(4)~20mA Yes 3.13s/mm (50Hz)TR5000-D24-S.12 5000N 4500N~5500N 24VAC 3-position Yes 3.13s/mm (50Hz)TR16000-XD220-S.12 16000N 16000N~16500N 220VAC 0(2)~10V, 0(4)~20mA Yes 1s/mm (50Hz)

Notes: 1. Operating voltage is available for 220V, which must be noted when ordering, the type should be changed from "24" to "220". For example, change "TC500-X24-S.12" to "TC500-X220-S.12". 2. 10K feedback function can be selected when actuator is 3-position type, which must be noted when ordering, the type should be changed from"S" to "SF10K". For example, change "TC500-X24-S.12" to "TC500-X24-SF10K.12". 3. SPDT feedback function also can be selected when actuator is 3-position type, which must be noted when ordering, the type should be changed from"S" to "SF2". For example, change "TC500-X24-S.12" to "TC500-X24-SF2.12". 4. S means manual function.5. The actual running time depends on the actual valve stroke.

Actuator Overview



Relationship between Differential Pressure and Flow

Mechanical Design

Flow direction

Medium flow relationship

Mounting with actuator

Mounting with pipe

2. Valve can be installed in the water supply pipe or return water pipe (priority selection). Besides, filter

and check valve are recommended to be installed. When the medium is steam, install draw off valve in

the pipe can remove the condensed water, or it will effect the life of valve.

10



flow direction:valve retracts:valve extends:

flow direction:valve retracts:valve extends:

2-portDN15~DN400

3-port mixingDN15~DN65

3-port diverting DN15~DN65

A,B to ABflow increasesflow decreases

A,B to ABA port flow increases,B port decreasesA port flow decreases,B port increases

AB to A,BA port flow increases,B port decreasesA port flow decreases,B port increases

3-port mixing DN15~DN65

3-port diverting DN15~DN65

A,B to ABA port flow increases,B port decreasesA port flow decreases,B port increases

AB to A,BA port flow increases,B port decreasesA port flow decreases,B port increases

The valve and actuator can be easily assembled without special tool and adjustment. See specification for installation details.

3-port mixing connection/valve DN15~DN65 /DN80~DN400

3-port diverting connection/valve DN15~DN65 /DN80~DN400

1.valve should be installed according to marked direction.

2-port DN15~DN400

2-port 3-port mixing connecting 3-port diverting connecting 3-port diverting valve DN15~DN400 DN15~DN65 DN15~DN65 DN80~DN400 3-port mixing valve DN80~DN400

Note: The 2-port valve closes when the stem extends.

MountingOrientation

Commissioning

Maintenance

Technical data

Operating Data

Material

11

Commission the valve only if the actuator has been mounted correctly.

Permissible Pressure

Standard of flanged connection

Leakage rate

Permissible media

Water valve

（-25℃~150℃）

Steam valve

（2℃~+180℃）

High-temp. Steam valve

Super-high-temp. Steam valve

Permissible pressure

Stroke

Valve body

Valve core

Stem

Seal ring

Sealing structure

PN16, PN25, PN40 are optional

ISO 7005-2

0.02% Kvs

Chilled water

Refrigerant（R12、R22、R134a、R202）

Glycol,Hydrazine,Phosphate,low and high temperatur hot water

Saturated steam（≤150℃ or ≤0.1MPa）

Saturated steam（≤0.89MPa),Overheated steam（≤180℃）

High-temperature steam(≤220℃)

Super-High-temperature steam(≤450℃)

1.6Mpa, 2.5Mpa, 4.0Mpa

20mm(DN15~DN80), 40mm(DN100~DN250)

Ductile iron

stainless steel

Stainless steel

Teflon

V model sealing gland + stainless steel spring auto-compensation auto-compensation (≤220℃ valve)

V model sealing gland + stainless steel spring auto-compensation+metal exhaust bellows(≤450℃ valve)

When doing service work on the valve / actuator:

1. Close the pump and turn off the power supply.

2. Close the shut-off valve, exhaust water in the pipe to reduce the pressure inside pipes. Make water

pipe(hot water) cool down naturally.

3. Dismantle electric wires from wiring terminals.

Remark: Valve should be fully open when doing the pipe pressure test and pipe flushing.

Medium is chilled/hot water Medium is steam

Downwards installation is forbidden Random Orientation is suitable



Dimensions

12

2-port 3-port

DN Bmm

Dmm

D2mm

D4mm

Kmm

L1mm

L2mm

2-portL3mm

3-portL3'mm

H1 H22-portweight

Kg

3-portweight

Kg

H-1mm

H-2mm

H-3mm

H-4mm

15 14 95 4-14 46 65 130 65 70 106 31 107 3.7 5.5 371 526 586 /20 16 105 4-14 56 75 150 75 70 106 31 107 4.3 5.5 371 526 586 /25 16 115 4-14 65 85 160 80 75 111 36 112 5.4 6.5 376 531 591 /32 18 140 4-18 76 100 180 90 80 121 45 121 7.7 9.4 385 540 600 /40 18 150 4-18 84 110 200 100 82 122 50 126 9.2 11.0 390 545 605 /50 20 165 4-18 99 125 230 115 98 136 60 136 12.5 14.8 400 555 615 /65 20 185 4-18 118 145 290 145 112 156 90 166 18.5 22.5 430 585 645 /80 22 200 8-18 132 160 310 155 130 185 120 196 25.0 28.8 460 615 675 /

1002-port

23 220 8-18 156 180 350 175150 - 136 212

35.6 40.6 /631 691 /

3-port - 202 162 238 657 717

125 24 250 8-18 184 210 400 200 175 240 157 233 50.6 55.4 / 652 712 /150 25 285 8-22 211 240 480 240 200 270 171 247 71.5 76.3 / 666 726 /200 26 340 12-22 266 295 500 250 236 320 263 339 112.7 125.6 / 758 818 /250 31 405 12-26 319 355 600 300 290 400 315 391 202 230.0 / 810 870 /

300

2-port

28 460 12-26 370 410 700 350

330 - 357 485

/ / / / /

13393-portMixing - 457 347 475 1329

3-portDiverting - 457 410 538 1392

350 46 520 16-26 429 470 788 394 400 520 437 565 / / / / / 1419400 48 580 16-30 480 525 912 456 420 595 487 615 / / / / / 1469



actu

ator

DN Bmm

Dmm

D2mm

D4mm

Kmm

L1mm

L2mm

2-portL3mm

3-portL3'mm

H1 H22-portweight

Kg

3-portweight

Kg

H-1mm

H-2mm

H-3mm

H-4mm

15 14 95 4-14 46 65 130 65 70 106 31 107 3.7 5.5 371 526 586 /20 16 105 4-14 56 75 150 75 70 106 31 107 4.3 5.5 371 526 586 /25 16 115 4-14 65 85 160 80 75 111 36 112 5.4 6.5 376 531 591 /32 18 140 4-18 76 100 180 90 80 121 45 121 7.7 9.4 385 540 600 /40 18 150 4-18 84 110 200 100 82 122 50 126 9.2 11.0 390 545 605 /50 20 165 4-18 99 125 230 115 98 136 60 136 12.5 14.8 400 555 615 /65 20 185 8-18 118 145 290 145 112 156 90 166 18.5 22.5 430 585 645 /80 22 200 8-18 132 160 310 155 130 185 120 196 25.0 28.8 460 615 675 /

1002-port

23 235 8-22 156 190 350 175150 - 136 212

35.6 40.6 /631 691 /

3-port - 202 162 238 657 717

125 24 270 8-26 184 220 400 200 175 240 157 233 50.6 55.4 / 652 712 /150 25 300 8-26 211 250 480 240 200 270 171 247 71.5 76.3 / 666 726 /200 26 360 12-26 274 310 500 250 236 320 263 339 112.7 125.6 / 758 818 /250 31 425 12-30 330 370 600 300 290 400 315 391 202 230.0 / 810 870 /

300

2-port

28 485 16-30 389 430 700 350

330 - 357 485

/ / / / /

13393-portMixing - 457 347 475 1329

3-portDiverting - 457 410 538 1392

350 46 555 16-33 448 490 788 394 400 520 437 565 / / / / / 1419400 48 620 16-36 503 550 912 456 422 595 487 615 / / / / / 1469

Note:B: thickness of flange D: excircle diameter of flange D2: quantity and diameter of bolt hole on flange D4: outer diameter of sealing surface K: bolt hole center line diameter L1: distance of left and right flange endL3: distance from 2-port flange center line to valve bottom L3': distance from 3-port flange center line to down flange end

H-1: distance from left and right flange center line to head of 500N, 1000N actuatorH-2: distance from left and right flange center line to head of 1800N, 3000N, 5000N actuator (without manual device)H-3: distance from left and right flange center line to head of 1800N, 3000N, 5000N actuator (with manual device)H-4: distance from left and right flange center line to head of 16000N actuator (with manual device)

BAS valve bodySeries TC500... TC1000... TR1800... TR3000... TR5000... TR16000...Nominal stroke 22mm 22mm 44mm 44mm 44mm 110mm

Nominal output force 500N 1000N 1800N 3000N 5000N 16000N

Basic application

● HVAC TC500.../ TC1000...

TR1800.../ TR3000...

TR5000...

TR16000...

3-position, 24VAC 3-position TC500-D24-S.12 TC1000-D24-S.12 TR1800-D24-S.12 TR3000-D24-S.12 TR5000-D24-S.12 -

proportional, 24VAC 0(2)...10VDC , 0(4)...20mA

TC500-X24-S.12 TC1000-X24-S.12 TR1800-X24-S.12 TR3000-X24-S.12 TR5000-X24-S.12 -

3-position, 220VAC 3-position TC500-D220-S.12 TC1000-D220-S.12 TR1800-D220-S.12 TR3000-D220-S.12 TR5000-D220-S.12 TR16000-XD220-S.12

proportional, 220VAC 0(2)...10VDC , 0(4)...20mA TC500-X220-S.12 TC1000-X220-S.12 TR1800-X220-S.12 TR3000-X220-S.12 TR5000-X220-S.12 TR16000-XD220-S.12

3-position,10K resistance(24VAC / 220VAC) 3-position TC500-D24-SF10K.12/

TC500-D220-SF10K.12TC1000-D24-SF10K.12/TC1000-D220-SF10K.12

TR1800-D24-SF10K.12/TR1800-D220-SF10K.12

TR3000-D24-SF10K.12/TR3000-D220-SF10K.12

TR5000-D24-SF10K.12/TR5000-D220-SF10K.12 -

3 position,2 SPDT feedback(24VAC /220VAC) 3-position TC500-D24-SF2.12/

TC500-D220-SF2.12TC1000-D24-SF2.12/TC1000-D220-SF2.12

TR1800-D24-SF2.12/TR1800-D220-SF2.12

TR3000-D24-SF2.12/TR3000-D220-SF2.12

TR5000-D24-SF2.12/TR5000-D220-SF2.12 -

Valve body Type DN StrokeFlow

parameterKvs

△Ps △Ps △Ps △Ps △Ps △Ps

[mm] [mm] [m3/h] [MPa] [MPa] [MPa] [MPa] [mPa] [MPa]

PN

16 , medium

temperature -25

℃ ~ 150

℃

Flanged water valve

(specilized valve for heating)

TF15-2VGC-S.12 DN15 20 2 1.60 1.60TF20-2VGC-S.12 DN20 20 3 1.10 1.60TF25-2VGC-S.12 DN25 20 5 0.70 1.60TF32-2VGC-S.12 DN32 20 8 0.40 1.60TF40-2VGC-S.12 DN40 20 20 0.25 1.60TF50-2VGC-S.12 DN50 20 31 0.30 0.60TF65-2VGC-S.12 DN65 20 50 0.18 0.45TF80-2VGC-S.12 DN80 20 80 0.30 0.45TF100-2VGC-S.12 DN100 40 125 0.28TF125-2VGC-S.12 DN125 40 200 1.60TF150-2VGC-S.12 DN150 40 300 1.60TF200-2VGC-S.12 DN200 40 520 1.60TF250-2VGC-S.12 DN250 40 750 1.60TF300-2VGC-Y.12 DN300 100 1200 1.60TF350-2VGC-Y.12 DN350 100 1800 1.60TF400-2VGC-Y.12 DN400 100 2200 1.60

PN

16 , medium

temperature 2 ℃

~ 180 ℃

Flanged steam valve

(universal valve for heating and

cooling)

TF15-2SGC-S.12 DN15 20 2 1.60 1.60TF20-2SGC-S.12 DN20 20 3 1.10 1.60TF25-2SGC-S.12 DN25 20 5 1.20 1.60TF32-2SGC-S.12 DN32 20 8 0.80 1.60TF40-2SGC-S.12 DN40 20 20 1.60TF50-2SGC-S.12 DN50 20 31 1.60TF65-2SGC-S.12 DN65 20 50 1.60TF80-2SGC-S.12 DN80 20 80 1.60TF100-2SGC-S.12 DN100 40 125 1.60TF125-2SGC-S.12 DN125 40 200 1.60TF150-2SGC-S.12 DN150 40 300 1.60TF200-2SGC-S.12 DN200 40 520 1.60TF250-2SGC-S.12 DN250 40 750 1.60TF300-2SGC-Y.12 DN300 100 1200 1.60TF350-2SGC-Y.12 DN350 100 1800 1.60TF400-2SGC-Y.12 DN400 100 2200 1.60

PN

16, medium

temperature -25 ℃

~ 150 ℃

+

3-way Flanged water valve

(universal valve for heating and

cooling)

TF15-3VGC-S.12 DN15 20 2 0.80 1.60TF20-3VGC-S.12 DN20 20 3 0.80 1.60TF25-3VGC-S.12 DN25 20 5 0.80 1.60TF32-3VGC-S.12 DN32 20 8 0.80 1.60TF40-3VGC-S.12 DN40 20 20 0.80 1.60TF50-3VGC-S.12 DN50 20 31 0.30 0.60TF65-3VGC-S.12 DN65 20 50 0.25 0.45TF80-3VGC-HS(FS).12 DN80 20 80 0.27 0.45TF100-3VGC-HS(FS).12 DN100 40 125 0.20TF125-3VGC-HS(FS).12 DN125 40 200 0.15TF150-3VGC-HS(FS).12 DN150 40 300 0.10TF200-3VGC-HS(FS).12 DN200 40 520 0.08 0.13TF250-3VGC-HS(FS).12 DN250 40 750 0.05 0.08TF300-3VGC-HY(FY).12 DN300 100 1200 0.25TF350-3VGC-HY(FY).12 DN350 100 1800 0.15TF400-3VGC-HY(FY).12 DN400 100 2200 0.10

Note: 1. Our company can provide 450℃ super high temperature steam valve. Caliber: DN15~DN400.e.g.2-port, DN150 super high temperature steam valve type is: TF150-2PGC-S.12.2. HS, HY stands for mixing valve, FS, FY stands for diverting valve.



13

Documents

Tiger Controls Equipment Co.,Ltd. - TL..-..BC-S.12 Series 2-port / 3 … · 2015. 3. 25. · Tiger Controls Equipment Co., Ltd Tel: 0086-429-6879888 Fax: 0086-429-6796222 Http: