Thermal Fire Pipe Sleeve - Stormflame · 2020. 10. 14. · Sleeves have also been tested in walls, for plastic pipes, leaving 25mm exposed for connection to standard pipe insulation

intumescent.comT: 01329 841 416 : F: 01329 841 417 : E: [email protected]

Intumescent.com : Unit 9 , The I.O Centre, Stephenson Road, Segensworth, Fareham, PO15 5RU.

www.intumescent.com

Thermal Fire Pipe SleeveProduct Data Sheet

CE Marked | Suitable for fire protecting a wide range of plastic and metal pipes | Tested to BS476 | Tested to BS EN 1366-3. Up to 2 Hours Fire Rating | Acoustic Tested to BSEN ISO 140-3 & BSEN ISO 717.

ETA - 14-0117 | CE-2812-CPR-0555 | Revision 10 - 17th February 2021

intumescent.com

T: 01329 841 416 : F: 01329 841 417 : E: [email protected] Intumescent.com : Unit 9 , The I.O Centre, Stephenson Road,

Segensworth, Fareham, PO15 5RUwww.intumescent.com

Thermal Fire Pipe SleeveCE Marked | ETA - 14-0117 | CE-2812-CPR-0555

Highlights

• CE Marked.• Suitable for fire protecting a wide range of

plastic and metal pipes.• Tested to BS476.• Tested to BS EN 1366-3.• Up to 2 Hours Fire Rating.• Acoustic Tested to BSEN ISO 140-3 and BSEN

ISO 717.• Maintains thermal insulation for the pipe.• For use through a wide range of fire partition• walls and floors.• Allows for thermal movement of pipe.• No additional metal sleeving or lining out of the• partition aperture required.• Cost effective, can be cut to length

About the Thermal Fire Pipe Sleeve Product

A high percentage of the steel, copper and plastic pipes found in commercial and domestic buildings will penetrate through fire rated constructions such as ceilings, floors and walls. Once a hole is made in a fire rated construction for the passage of pipes or services the integrity of the compartment is compromised. To solve this problem we have developed the Thermal Fire Pipe Sleeve, which reinstates the fire rating of the construction and prevents fire spreading from one compartment to another. It also protects copper pipes from cement erosion.

The Thermal Fire Pipe Sleeve is a cost effective product for the fire stopping of pipe penetrations, e.g. plumbing pipe and metallic pipes, whilst maintaining similar thermal and acoustic properties as standard mineral fibre insulation. These properties ensure compliance to water bye laws and building regulations for cold and hot water pipes and heating systems.

In a fire situation the sleeve expands to fill the available space between the pipe and the penetration. In the case of plastic pipes the sleeve will crush and close off the pipe forming a solid char and preventing

the passage of fire and smoke to the adjacent compartment. Tested in Plasterboard Partition, Mineral Fibre Batt, Solid Walls and Floors.

tel:01329841416mailto:sales%40intumescent.com?subject=http://www.astroflame.com

intumescent.com




Technical Information

Tested on the following pipe sizes to BS 476 and BS EN 1366-3 for up to 2 hours.

BS 476

COPPER Pipe Size 12mm - 160mm 120 mins

STAINLESS STEEL Pipe Size 15mm - 160mm 120 mins

MILD STEEL Pipe Size 15mm - 165mm 120 mins

CAST IRON Pipe Size 15mm- 160mm 120 mins

PVC Pipe Size 55mm- 110mm 120 mins

PVC Pipe Size 160mm 90 mins

POLYBUTYLENE Pipe Size 12mm - 28mm 120 mins

HDPE Pipe Size 15mm - 160mm 120 mins

EN 1366-3

METAL Pipe Size 15mm - 158mm EI 120 Wall

METAL Pipe Size 159mm E120 EI30 Wall

PVC Pipe Size 43mm - 160mm EI 120 min wall & floor

HDPE Pipe Size 40mm - 110mm 120 min wall & floor

HDPE Pipe Size 160mm EI 90 wall / EI 120 floor

All sleeves have been tested with a 25mm nominal wall thickness. Sleeves have been tested cut flush to the wall for metal pipes only and floor for metal and plastic pipes. Sleeves have also been tested in walls, for plastic pipes, leaving 25mm exposed for connection to standard pipe insulation.

The Thermal Fire Pipe Sleeve is simple to install, easy to cut and one sleeve can replace two collars. For metal pipes the sleeve may also be fitted flush to the wall for a clean line solution.


intumescent.com




Pipe Material Diameter Blockwork WallSolid Floor

Mineral batt (BS only)

Plasterboard Wall

COPPER Pipe Size 15mm - 160mm • • •

CAST IRON Pipe Size 15mm - 160mm • •

MILD STEEL Pipe Size 15mm - 160mm • • •

STAINLESS STEEL Pipe Size 15mm - 160mm • • •

POLYBUTYLENE Pipe Size 12mm • • • •

POLYBUTYLENE Pipe Size 28mm • • • •

PVC Pipe Size 55mm - 110mm • • • •

PVC Pipe Size 160mm • • •

PVC-U Pipe Size 15mm - 160mm • • •

HDPE Pipe Size 15mm - 160mm •* • •*

* HDPE 160mm limited to EI90

For specific details of approved pipe materials, pipe thickness and substrates check with intumescent.com Technical Team


intumescent.com




Product Size Availability

Product Code Product Description DiameterAFIPS17/2E Thermal Fire Pipe Sleeve 17mm 17mm AFIPS21/2E Thermal Fire Pipe Sleeve 21mm 21mm AFIPS27/2E Thermal Fire Pipe Sleeve 27mm 27mm AFIPS34/2E Thermal Fire Pipe Sleeve 34mm 34mm AFIPS42/2E Thermal Fire Pipe Sleeve 42mm 42mm AFIPS48/2E Thermal Fire Pipe Sleeve 48mm 48mm AFIPS54/2E Thermal Fire Pipe Sleeve 54mm 54mm AFIPS60/2E Thermal Fire Pipe Sleeve 60mm 60mm AFIPS67/2E Thermal Fire Pipe Sleeve 67mm 67mm AFIPS76/2E Thermal Fire Pipe Sleeve 76mm 76mm AFIPS80/2E Thermal Fire Pipe Sleeve 80mm 80mm AFIPS89/2E Thermal Fire Pipe Sleeve 89mm 89mm AFIPS102/2E Thermal Fire Pipe Sleeve 102mm 102mm AFIPS108/2E Thermal Fire Pipe Sleeve 108mm 108mmAFIPS114/2E Thermal Fire Pipe Sleeve 114mm 114mmAFIPS127/2E Thermal Fire Pipe Sleeve 127mm 127mmAFIPS140/2E Thermal Fire Pipe Sleeve 140mm 140mmAFIPS159/2E Thermal Fire Pipe Sleeve 159mm 159mmAFIPS169/2E Thermal Fire Pipe Sleeve 169mm 169mm

The Thermal Fire Pipe Sleeve is 300mm in length, Wall thickness 25mm.

Fire Test and Assessment Reports

• CE Marked• BS476.• BS EN 1366-3• Acoustically Tested in plasterboard to BS EN ISO 140-3 and BS EN ISO 717:1977• Includes Uncapped/Uncapped testing (u/u) only on Astro Thermal Fire PS+ please contact us for details on

this product


intumescent.com




Orders can be placed securely from our online shop please go to www.intumescent.com For any help or general advise please contact the team: Tel: 01329 841 416 Fax: 01329 841 417 Email: [email protected]

How to order

Please refer to the ETA sheet for fields of application for this product. For further information on installation requirements please refer to the pipe manufacturer data and wall specification to ensure the compatibility of this product, if in doubt please contact the technical team with services and wall specification on: Tel: 01329 841 416 Fax: 01329 841 417 Email: [email protected]

Installation

Please see Safety Data sheet (SDS) - This can be requested from our sales team: Tel: 01329 841 416 Fax: 01329 841 417 Email: [email protected]

Health and Safety

As part of our policy of ongoing improvements, we reserve the right to modify, alter or change product specifications without giving notice. Product illustrations are representations only. All information contained in this document is provided for guidance only, and as Intumescent.com (Part of the Stormflame Group) has no control over the specific application or installation methods of the products, or of the prevailing site conditions, no warranties expressed or implied are intended to be given as to the actual performance of the products mentioned or referred to, and no liability whatsoever will be accepted for any loss, damage or injury arising from the use of the information given of products mentioned or referred to herein.

The above information to the best of our knowledge is true and accurate and based upon current test data and is supplied for your guidance only. Customers should satisfy themselves to the suitability of the product based on the products limitation of applications and that the product is fit for purpose for their intended use and no guarantee is given or implied since the conditions of actual use are beyond our control. Intumescent.com (Part of the Stormflame Group), disclaim any liability for loss, damage or other expense arising from the use of information, data or products mentioned or referred to and reserve the right to change any details or specifications without notice. If you are in any doubt as to the suitability of this product for your intended application please contact our technical team on 01329 841 416 or email [email protected] and we will contact you.
tel:01329841416mailto:sales%40intumescent.com?subject=http://www.astroflame.comhttp://www.intumescent.comtel:01329841416mailto:sales%40intumescent.com?subject=tel:01329841416mailto:sales%40intumescent.com?subject=tel:01329841416mailto:sales%40intumescent.com?subject=

Documents

Thermal Fire Pipe Sleeve - Stormflame · 2020. 10. 14. · Sleeves have also been tested in walls, for plastic pipes, leaving 25mm exposed for connection to standard pipe insulation