RE

MS

MIN

I P

RE

SS

AC

C

1800 4 ANCRA www.ancraaustralia.com

POM_December 2016_Mini Press ACC

REMS MINI PRESS ACC

SECURE CRIMPING IN SECONDS. PEX UP TO Ø 40mm. COPPER/SS UP TO Ø 32mm. AUTOMATIC LOCKING OF PRESSING TONGS.

The Rems Mini Press ACC is a universal, super light handy electric tool with automatic circuit control for producing pipe pressing joints for all common pressfitting systems. This powerful tool comes with both battery and corded operation. It is capable of pipe pressing PEX joints Ø 10–40 mm and Copper/SS joints Ø 10–32 mm.

There is also a complete range of REMS Mini pressing tongs for all common pressfitting systems such as:

The solution for secure crimping of PEX piping (up to 40mm) and COPPER & STAINLESS STEEL piping (up to 32mm)

ACCESSORIES The REMS Mini Press ACC has an assortment of REMS pressing tongs Mini for all common pressfitting systems.

ANCRA OFFICES

VICTORIA (H/OFFICE): Phone: 03 9587 6700 NEW SOUTH WALES: Phone: 02 9604 8000 QUEENSLAND: Phone: 07 3217 9175 WESTERN AUSTRALIA: Phone: 08 9358 2773

ACCESSORIES:REMS pressing tongs/Mini pressing ringsREMS cropping tongs MiniREMS Mini Press ACC drive unit, without battery 578001Battery Li-Ion 14.4 V, 1.5 AhBattery Li-Ion 14.4 V, 3.0 AhRapid charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 WVoltage supply Li-Ion 230 V/14.4 V for mains operation 230 V instead of battery Li-Ion 14.4 V.Steel case with inlayREMS cordless LED lamp

Supply format of REMS Mini Press ACC Basic Pack:• Cordless radial press with automatic circuit control for producing

pipe pressing joints PEX: Ø 10–40mm. Copper/SS: Ø 10–32mm.• Swivelling pressing tongs seat with automatic locking. • Electro-hydraulic drive with powerful battery motor 14,4 V, 380 W,• Robust planetary gear• Eccentric reciprocating pump and compact high power hydraulic

system. Safety tip switch.• Integrated LED work light• Battery Li-Ion 14,4 V, 1.5 Ah, rapid charger Li-Ion/Ni-Cd 230 V

or 110 V, 50 – 60 Hz, 65 W. • Sturdy steel case.

126

with automatic circuit controland charging status check

REMS Mini-Press ACC Cordless radial press with automatic circuit control

German Quality ProductGerman Quality Product

Universal, super handy electric tool with automatic circuit control for producing pipe pressing joints for all common pressfi tting systems. For battery and corded operation.Pipe pressing joints Ø 10 – 40 mm 7 Ø ⅜ – 1 ¼Complete range of REMS pressing tongs Mini for all common pressfi tting systems, see page 128 – 142.

REMS Mini-Press ACC – universal up to Ø 40 mm.Super light, super small, super handy. With automatic circuit control. Secure crimping inseconds. Automatic locking of the pressing tongs. Pressing tongs for all common systemsComplete assortment of REMS pressing tongs Mini for all common pressfi tting systems (page 128 – 142). Highly durable pressing tongs made of forged, tenacious, specially hardened special steel. Pressing contours of REMS pressing tongs are system-specifi c and correspond to the respective pressfi tting system. Thus perfect system-conformity, safe press jointing. Very compact design and low weight of the REMS Mini pressing tongs due to special arrangement of the pressing tongs connection (Patent EP 1 952 948). Recesses in the pressing jaws for safe guidance of the connecting plate for offset-free pressing (Patent EP 2 347 862).DesignSuper light, super small, super handy. Drive unit with battery only 2.4 kg. Drive unit with pressing tongs V 22 only 33 cm long. Works anywhere, free-hand, overhead, also in particularly tight areas. Optimum weight distribution for single-hand oper-ation. Ergonomically designed housing. Integrated LED work light for illuminating the work place. Swivelling pressing tongs seat. Secure seating of pressing tongs by automatic locking. For battery and corded operation. Electronic charging status check with fl at battery protection and charging status indicator with 2-coloured LED.

Pressing operation by touch-control with ACCFor reliable service, operating and functional safety. Automatic retraction after completion of pressing operation (automatic circuit control).

DriveEnormous thrust and pressing force for fast and perfect press jointing. Powerful electro-hydraulic drive with powerful battery motor 14,4 V, 380 W output, robust planetary gear, eccentric reciprocating pump and compact high power hydraulic system. Safety tip switch.

Battery or mains operationLi-Ion PLUS technology. Highly resistant Li-Ion 14.4 V battery with 1.5 or 3.0 Ah capacity for long service life. Powerful and light. Li-Ion 14.4 V, 3.0 Ah battery for approx. 330 pressings Viega Profi press DN 15 per battery charge. Total discharge and overload protection with single cell monitoring. Temperature monitoring during the charging process. Operating temperature range –10 to +60 °C. No memory effect for maximum battery power. Rapid charger for short charging times. Li-Ion 230 V/14.4 V voltage supply for mains operation 230 V instead of Li-Ion battery 14.4 V, as accessory.

Supply formatREMS Mini-Press ACC Basic-Pack. Cordless radial press with automatic circuit control for producing pipe pressing joints Ø 10–40 mm, Ø ⅜ – 1 ¼". For operating with REMS pressing tongs Mini. Swivelling pressing tongs seat with automatic locking. Electro-hydraulic drive with powerful battery motor 14,4 V, 380 W, obust planetary gear, eccentric reciprocating pump and compact high power hydraulic system, Safety tip switch. Integrated LED work light. Battery Li-Ion 14,4 V, 1.5 Ah, rapid charger Li-Ion/Ni-Cd 230 V or 110 V, 50 – 60 Hz, 65 W. In sturdy steel case.

Art.-No.578012 R220

Other voltages on request.

AccessoriesAccessories

Description Art.-No.REMS pressing tongs Mini/pressing rings see page 128 – 142.REMS cropping tongs Mini for threaded rods see page 143.REMS Mini-Press ACC drive unit, without battery 578001 R14

Battery Li-Ion 14.4 V, 1.5 Ah 571545 R14

Battery Li-Ion 14.4 V, 3.0 Ah 571555 R14

Rapid charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W 571560 R220

Voltage supply Li-Ion 230 V/14.4 V for mains operation 230 V instead of battery Li-Ion 14.4 V. 571565 R220

Steel case with inlay 578290 R

REMS cordless LED lamp see page 95 175200 R

Patent EP 1 952 948Patent EP 2 347 862

< 33 cm (V 22)

FORZA CRIMP WATER = K TONGS FORZA CRIMP GAS = K TONGS FORZA COPPER PRESS = VAU TONGS STESSO CRIMP = U TONGS BUSHPEX = TH MINI CRIMP PLUS = K TONGS DUOPEX WATER = TH TONGS DUOPEX GAS = TH TONGS K1 GAS = K TONGS K2 WATER = K TONGS FLOWPEX = TH MINI WATER PEX = U TONGS GAS PEX = U TONGS COPPER CRIMP = VAU TONGS TRADEPEX CRIMP = K TONGS

The Rems Mini-Press is every plumbers’ dream. Versatile, durable and built for the tough Australian climate, it’s the perfect partner for every plumber. German made, the Rems Mini-Press is a unique radial pressing tool because it will use different Rems tongs for different systems. No longer does a plumber need have multiple tools! Simply change the tongs in the Rems Mini-Press depending on what system you’ll be crimping. For example, crimping Kempress copper and needing to swap over to Auspex? No issue. A quick change of Rems VAU-tongs to K-tongs will have you saving time and money.The Mini Press is super light, super small and super handy. Its drive unit with battery weighs only 2.4 kg. The drive unit with pressing tongs V22 is only 33cm long. It works anywhere, free-hand, overhead, also in very tight areas. There is optimum weight distribution for single-hand operation and ergonomically designed housing. The integrated LED work light is for illuminating the work place. Swivelling pressing tongs seat allow great flexibility when working and the secure seating of pressing tongs by automatic locking allows you to keep your mind on the job at hand!. For battery and corded operation. Electronic charging status check with flat battery protection and charging status indicator with 2-coloured LED.