111

LEXMARK BLACK CARTRIDGE Lexmark: 150C, 1000, 1020 1100, 2030, 2050, 2055, 2070, 3000, 3100, 3200, 4076, 5000, 5700, 5770, 7000, 7200, 7200v, X63, X70, X73, X80, X83, X84, X85, X85 Pro, X125, X4250, X4270, Z11, Z12, Z22, Z31, Z32, Z42, Z43, Z44, Z45, Z45se, Z51, Z52, Z53, Z54, Z54se, Z82, Z700, Z703, Z705, Z706, Z708, Z715, F4270, P700, P704, P706, P707, P3120, P3140, P3150. Optracolor:

40, 45. Medley: 4c, 4x, 4sx. Execjet: II, IIC. OKI: 2010. Compaq SmartJet: C20, IJ200, IJ600, 300, 600, 700, 900, 1200, Xerox: 365, 365c,470, 470cx, 480cx, 490, 570, 155C, XJ8C, XJ9C, XK35, XK-35c, XK-50, XK-50cx, C20, CW470, NC-20,

XI-470. Canon 710, Brother: 810, 840 BT: 50, 55, 60, 65, 300 Sharp WinWrite: 100, 150C, Samsung.

1. Enlarge the filling hole sufficiently to accept the steel filling tube using the screw provided.(See diagram above). IMPORTANT: DO NOT REMOVE TOP.2. Fill syringe with ink, insert the steel filling tube into the filling hole and push downwards into thecentre of the sponge. 3. SLOWLY inject ink, when the ink overflows from filling hole cartridge is full. Stop injecting inkimmediately. DO NOT reseal filling hole.IMPORTANT: Clean syringe with water and dry.4. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure noleakage and give the ink time to fully saturate the sponge. IMPORTANT: DO NOT LEAVE ON TISSUE.5. Install cartridge and run a priming cycle. (When installing the cartridge the printer may ask if the cartridge is NEW or OLD cartridge.click on NEW to reset the printer)

IMPORTANT: For best results, refill whilst ink still remains in cartridge.Empty cartridges should be refilled immediately.

The Lid Colour of the Cartridge Can

Change Depending On Model Type.

Print HeadPrinted Circuit

Filling Hole

112

LEXMARK COLOUR & PHOTOLexmark: 150C, 1000, 1020 1100, 2030, 2050, 2055, 2070, 3000, 3100, 3200, 4076, 5000, 5700, 5770, 7000, 7200, 7200v, X63, X70, X73, X80, X83, X84, X85, X85 Pro, X125, X4250, X4270, Z11, Z12, Z22, Z31, Z32, Z42, Z43, Z44, Z45, Z45se, Z51, Z52, Z53, Z54, Z54se, Z82, Z700, Z703, Z705, Z706, Z708, Z715, F4270, P700, P704, P706, P707, P3120, P3140, P3150. Optracolor:

40, 45. Medley: 4c, 4x, 4sx. Execjet: II, IIC. OKI: 2010. Compaq Smartjet: C20, IJ200, IJ600, 300, 600, 700, 900, 1200, Xerox: 365, 365c,470, 470cx, 480cx, 490, 570, 155C, XJ8C, XJ9C, XK35, XK-35c, XK-50, XK-50cx, C20, CW470, NC-20,

XI-470. Canon 710, Brother: 810, 840 BT: 50, 55, 60, 65, 300 Sharp WinWrite: 100, 150C, Samsung.

1. The filler holes are located under the coloured top of the cartridge. This top needs to be removed before filling. Use a penknife or Stanley knife to break the seal by carefully scoring around all four edges of seal. (Colour & Photo cartridge only)2. Assemble syringe and steel filling tube and fill with appropriate colour ink.3. Insert the steel filling tube into the appropriate filling hole. (See diagram above).Push downwards into the centre of the sponge.IMPORTANT: Cartridge contains a sponge and a slight resistance may be felt. 4. SLOWLY inject ink. When ink overflows from filling hole or starts to leak from print heads, cartridge is full. Stop injecting immediately. Blot printer head with tissue before continuing to fill next colour.IMPORTANT: Clean syringe with water and dry before refilling next colour.5. After refilling reseal the top. The best way to secure the top is to stick tape from one side, over the top and down the opposite side.6. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure no leakage and give the ink time to fully saturate the sponge. IMPORTANT: DO NOT LEAVE ON TISSUE.7. Install cartridge and run a priming cycle. (When installing the cartridge the printer may ask if the cartridge is a NEW or OLD cartridge. click on NEW to reset the printer)

IMPORTANT: For best results, refill whilst ink still remains in cartridge.Empty cartridges should be refilled immediately.

Print Head

Light CyanFilling Holes

BlackFilling Holes

Light Magenta Filling Holes

YellowFilling Holes

The Lid on Colour & Photo Cartridges Can Change Depending On

Model Type.

Carefully score around the seal of the cartridge lid with a sharp knife

Print Head

Magenta Filling Holes

CyanFilling Holes

113

Print Head

Colour Cartridge With Lid Removed

Magenta Filling Holes

YellowFilling Holes

CyanFilling Holes

Carefully Lever the cartridge lid with a sharp knife i.e. Pen

knife.

LEXMARKLexmark: Z55, Z55se, Z65, Z65n, Z65p, X5100, X5130, X5150,

X5190, X6150, X6170, X6190Pro. Dell: 740, 940, 960.

1. The filler holes are located under the coloured top of the cartridge. This top needs tobe removed before filling. Use a penknife or Stanley knife to break the seal by carefullyscoring around all four edges of seal. (Colour cartridges only).2. Assemble syringe and steel filling tube and fill with appropriate colour ink.3. Insert the steel filling tube into the appropriate filling hole. (See diagram above).Push downwards into the centre of the sponge.IMPORTANT: Cartridge contains a sponge and a slight resistance may be felt. 4. SLOWLY inject ink. When ink overflows from filling hole or starts to leak from printheads, cartridge is full. Stop injecting immediately. Blot printer head with tissue beforecontinuing to fill next colour.IMPORTANT: Clean syringe with water and dry before refilling next colour.5. After refilling reseal the top. The best way to secure the top is to stick tape from one side,over the top and down the opposite side.6. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensureno leakage and give the ink time to fully saturate the sponge. IMPORTANT: DO NOT LEAVE ON TISSUE.7. Install cartridge and run a priming cycle. When installing the cartridge the printermay ask if the cartridge is a NEW or OLD cartridge. click on NEW to reset the printer.

IMPORTANT: For best results, refill whilst ink still remains in cartridge.Empty cartridges should be refilled immediately.

114

LEXMARKLexmark: Z55, Z55se, Z65, Z65n, Z65p, X5100, X5130, X5150,

X5190, X6150, X6170, X6190Pro. Dell: 740, 940, 960.

1. Enlarge the filling hole sufficiently to accept the steel filling tube using the screw provided. IMPORTANT: DO NOT REMOVE TOP.2. Fill syringe with ink, insert the steel filling tube into the filling hole and push downwards into the centre of the sponge. 3. SLOWLY inject ink, when the ink overflows from filling hole cartridge is full. Stop injecting ink immediately. DO NOT reseal filling hole.IMPORTANT: Clean syringe with water and dry.4. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure no leakage and give the ink time to fully saturate the sponge. IMPORTANT: DO NOT LEAVE ON TISSUE.5. Install cartridge and run a priming cycle. (When installing the cartridge the printer may ask if the cartridge is a NEW or OLD cartridge. click on NEW to reset the printer)

IMPORTANT: For best results, refill whilst ink still remains in cartridge.Empty cartridges should be refilled immediately.

Filling Hole

Print Head

115

LEXMARKLexmark: I3, Z13, Z23, Z24, Z25, Z25I, Z33, Z34, Z35, Z513, Z515, Z517,

Z600, Z601, Z604, Z605, Z612, Z615, Z617, X72, X74, X75, X1100, X1130, X1150, X1160, X1170, X1180, X1185, X1190, X2200, X2230, X2250. 4126.

Lexmark Jetprinter: A10. Dell: 720, 920.

1. The filler holes are located under the coloured top of the cartridge. This top needs tobe removed before filling. Use a penknife or Stanley knife to break the seal by carefullyscoring around all four edges of seal. (Colour cartridge only)2. Assemble syringe and steel filling tube and fill with appropriate colour ink.3. Insert the steel filling tube into the appropriate filling hole. (See diagram above). Pushdownwards into the centre of the sponge.IMPORTANT: Cartridge contains a sponge and a slight resistance may be felt. 4. SLOWLY inject ink. When ink overflows from filling hole or starts to leak from printheads, cartridge is full. Stop injecting immediately. Blot printer head with tissue beforecontinuing to fill next colour.IMPORTANT: Clean syringe with water and dry before refilling next colour.5. After refilling reseal the top. The best way to secure the top is to stick tape from one side,over the top and down the opposite side.6. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensureno leakage and give the ink time to fully saturate the sponge.IMPORTANT: DO NOT LEAVE ON TISSUE.7. Install cartridge and run a priming cycle. (When installing the cartridge the printer mayask if the cartridge is NEW or OLD cartridge. click on NEW to reset the printer).

IMPORTANT: For best results, refill whilst ink still remains in cartridge.Empty cartridges should be refilled immediately.

Remove Lid

Print Head

Colour Cartridge With Lid Removed

Yellow Filling Holes

Magenta Filling Holes

CyanFilling Holes

Print Head End

116

Filling Hole

Print Head

LEXMARKLexmark: I3, Z13, Z23, Z24, Z25, Z25I, Z33, Z34, Z35, Z513, Z515, Z517,

Z600, Z601, Z604, Z605, Z612, Z615, Z617, X72, X74, X75, X1100, X1130, X1150, X1160, X1170, X1180, X1185, X1190, X2200, X2230, X2250. 4126.

Lexmark Jetprinter: A10. Dell: 720, 920.

1. Enlarge the filling hole sufficiently to accept the steel filling tube using the screw provided. IMPORTANT - DO NOT REMOVE TOP.2. Fill syringe with ink, insert the steel filling tube into the filling hole and push downwards into the centre of the sponge. 3. SLOWLY inject ink, when the ink overflows from filling hole cartridge is full. Stop injecting ink immediately. DO NOT reseal filling hole.IMPORTANT: Clean syringe with water and dry.4. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure no leakage and give the ink time to fully saturate the sponge.IMPORTANT: DO NOT LEAVE ON TISSUE.5. Install cartridge and run a priming cycle. (When installing the cartridge the printer may ask if the cartridge is NEW or OLD cartridge. click on NEW to reset the printer)

IMPORTANT: For best results, refill whilst ink still remains in cartridge.Empty cartridges should be refilled immediately.

117